Instruction/ maintenance manual of the product 1000XT Flymo
Go to page of 9
IMPOR T ANT INFORMA TION Read before use & retain for future reference For all customer enquiries or for replacement parts, contact:- ☎ ☎ 0870 609 1901 www .
Carton Contents IMPOR T ANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY P AR TS ARE MISSING CONT ACT :- Husqvarna Outdoor Products Customer Service Department direct:- T elephone : 0870 609 1901 Fax : 0870 609 1902 Safety General 1.
3. Do not use the product if the electric cables are damaged or worn. 4. Immediately disconnect from the mains electricity sup- ply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical sup- ply has been disconnected.
Switch Handle and Handle T ube Assembly (A), (B) & (C) 1. Loosen the four bolts on the Handle Clamp (A) . 2. Insert the Switch Handle and the Steady Handle into the holes at the side of the Handle Clamp (B1 Right Handed) (B2 Left Handed) - using the Hex Drive T ool to turn the switch handle (B3) 3.
J1 J2 Assembly Instructions cont’ Line Feed • WARNING • W ear eye protection. Do not lean over the trimmer whilst trimming, objects may be thrown by the cutting line. Do not allow cutting head to rest on the gr ound. Do not overload your trimmer .
Cutting Head T o replace nylon line. For your convenience it is recommended you buy spool and line complete. Nylon line only is also available. Both are available from Husqvarna Outdoor Products stockists. T o fit spool and line complete: 1. Remove the Cap (Q1) and Spool Holder (Q2) 2.
Maintenance X W • WARNING Disconnect from the mains electricity sup- ply , before attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard.
Fault Finding Chart WARNING Disconnect from the mains electricity supply befor e attempting any maintenance or adjustment. F AUL T CHECK ACTION Is the line fed out and visible? Has line been removed from cleat? Remove cap and spool, free line and re-fit spool and cap.
5107683-02 Husqvarna Outdoor Products Aycliffe Industrial Park NEWTON A YCLIFFE Co.Durham DL5 6UP ENGLAND T elephone - 0870 609 1901 Fax - 0870 609 1902 Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
An important point after buying a device Flymo 1000XT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Flymo 1000XT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Flymo 1000XT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Flymo 1000XT you will learn all the available features of the product, as well as information on its operation. The information that you get Flymo 1000XT will certainly help you make a decision on the purchase.
If you already are a holder of Flymo 1000XT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Flymo 1000XT.
However, one of the most important roles played by the user manual is to help in solving problems with Flymo 1000XT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Flymo 1000XT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
