Instruction/ maintenance manual of the product S2000 Field Controls
Go to page of 16
MODELS S2000 AND S2020 FOR GAS OR OIL FORCED AIR FURNACES, HEA T PUMPS AND ELECTRIC FURNACES has been designed to be simple to Install, Operate and Maintain. Read this manual before you install the Humidifier . Parts included in the Steam Humidifier package ar e: 1.
SIMPLIFIED INST ALLA TION INSTRUCTIONS DET AILED INST ALLA TION INSTRUCTIONS 1. Insulate the water reservoir . See figure 3. 2. Select the mounting location on the duct and tape on the mounting template. 3. Drill the (8) 1/8" mountings holes. 4. Cut out the humidifier opening in the duct.
6. W A TER SUPPL Y - Required Criteria 9. WIRING THE STEAM HUMIDIFIER 7. M O U N T I N G T H E S T E A M H U M I D I F I E R 8. STEAM OPERA TION - Required Criteria A. W A TER SUPPL Y USING THE SADDLE V AL VE FURNISHED WITH UNIT . Important! See page 14.
Typi ca l Furnace S2000 & S2020 Humidifier Low V oltage T erminal Block G1 R G2 H H Heat only Thermostat W R G W R Heat Only System and Steam Humidifier with standard dry contact Humidistat Dry Contact Humidistat A A FIG. 6 Factory Jumper will stay in place unless a field installed Air Proving Device is used.
8 . 0 0 ” 6 . 00 ” 7.50” 8 . 2 5 ” 1 0 . 5 0 ” 1 1 . 6 0 ” the room needed to install the unit in a certain location. The data can also be used to determine the minimum duct size the Steam Humidifier can be inserted into. The Steam Humidifier should not obstruct more than 25% of the cross sectional area of the selected duct.
F o r R e p l a c e m e n t P a r t s C a l l ( 8 0 0 ) 4 4 6 - 3 1 1 0 0 9 0 2 1 A 0 1 1 8 U . S . P A T E N T N U M B E R 5 7 5 8 0 1 8 s e r i a l n u m b e r E w c 3 8 5 H i g h w a y 3 3 , E n g l i s h t o w n , N J 0 7 7 2 6 C O N T R O L S , I N C .
It is recommended that humidistat settings of 30-45% not be exceeded. If condensation is noticed on windows during very cold outside temperatures, the humidistat setting should be lowered.
INITIAL ST AR T -UP * SEQUENCE OF OPERA TION * SER VICE “LED” INDICA TORS 1 1. ST AR T -UP & OPERA TING SEQUENCE Once the Steam Humidifier has been installed and the w a t e r, d r a i n , h u m i d i s t a t a n d b l o w e r i n t e r l o c k connections completed, the humidifier may be started.
14. SERVICE INDICA T ORS Seven LED lamps provided on the front panel indicate the functional status of the humidifier as shown in Figure 7 below . 9 A. L. M. N. O. B. C. D. E. F . G. H. I. J. K. Unplug the power cord from the 120 volt source for S2000 (240 volt for S2020) and allow the water to cool for at least 30 minutes prior to removal.
10 A. G. B. C. D. E. F . The green "Power" light does not blink off and on. 1. The S2000 is not connected to an active 120 V AC 15 Amp power source. (S2020, 240 V AC, 10 AMP). 2. Call the T echnical Support Hotline. The "HEA TER" LED does not illuminate.
SERVICE AND REPLACEMENT P ARTS 11 ITEM 1 120 VOL T HEA TER A SSEMBL Y 240 VOL T HEA TER A SSEMBL Y 24 VOL T SOLENOID V AL VE A SSEMBL Y W A TER LEVEL PROBE A SSEMBL Y THERMISTOR PROBE A SSEMBL Y CIRCU.
Figure 18 12 DRAIN COCK V AL VE "T" ADAPTER, 1/4" NPT OVERFLOW TUBE, .50 ID x 6" LG. BARBED TEE, 1/4-18 NPT TO ½ " JUMPER WIRE, 20GA. X 1.50" LONG MOLEX PLUG BLACK WIRES 18GA. X 18" LONG SOLENOID V AL VE, 24/60 V AC 2 63 0 A irp o rt Ro a d K in s t on , N C 28 5 04 P H : 2 52 .
Smart Digital Humidistat Installation and Owner's Manual The 072000 is a digital humidifier control that can automatically adjust the indoor humidity set point as the outside air t em p e r a tu r e c h an g e s . T h is i n t e ll i g e n t control will maintain accurate humidity levels and a more comfortable indoor environment.
Z100 A SSEMBL Y INST ALL A TION INSTRUCTIONS & OWNER'S MANUAL Z100 REPL ACEMENT INSTRUCTIONS ELECTRONIC STEAM POWER HUMIDIFIERS MODEL # S2000 AND S2020 APPLICA TION NOTE AN 131 C o p yr igh t © 2 0 1 1 Fi e ld Co n trols A l l Ri g h t s Rese rved .
APPLICA TION NOTE P ART # 2009 AN 151 SC100 - P AR T # 2009 DECORA TIVE COVER S2000/S2020 STEAM HUMIDIFIER SC100 Installation Instructions P/ N 09 0 3 76 A0 15 1 R EV.
16 Model Number:____________________Serial Number:____________________Date Code:_____________________ Date Purchased:_________________________________________________________________________________ D.
An important point after buying a device Field Controls S2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Field Controls S2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Field Controls S2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Field Controls S2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Field Controls S2000 will certainly help you make a decision on the purchase.
If you already are a holder of Field Controls S2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Field Controls S2000.
However, one of the most important roles played by the user manual is to help in solving problems with Field Controls S2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Field Controls S2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
