

Personal Series
USE AND CARE MANUAL

PRODUCT USAGE GUIDE
CC4-2 Sheet capacity*: 5 Shred type: Confetti Shred size: 5/32" x 2" Entry width: 9-1/2" Recommended use: 10-20 shredding passes per day Maximum running time: 5-7 min. on/15 minutes off
*Sheet capacity measured with 20 lb., 8-1/2" x 11" paper with the shredder operating at rated voltage. Different paper weights, humidity, and electrical currents will affect capacity.
Customer Service: 1-800-955-0959

PARTS OF THE SHREDDER
¥ NEVER insert hands or fingers into paper entry as
serious personal injury may result. ¥ THIS MACHINE IS NOT A TOY. Keep children and
pets away from shredder AT ALL TIMES as serious injury may result. Always unplug shredder when not in use. ¥ Keep loose objects (jewelry, ties, long hair) away
from shredder. These items and others like them may cause serious injury if they accidentally fall into the paper entry.
¥ Confetti cut shredders contain sharp edges on the
A. Paper entry B. Basket C. Red LED D. Auto-start sensor
E. Power switch F. Shredder head
underside of the machine. Use caution when posi- tioning the shredder head onto the basket. ¥ Do not exceed recommended sheet capacity. ¥ Do not shred plastic, continuous forms, adhesive
labels, transparencies, glossy paper, newsprint, or cardboard. ¥ This personal shredder is intended for paper only.
Do not attempt to shred paper clips or other hard materials (except staples). ¥ Do not place shredder near or over a heat source or
water. ¥ Always turn off and unplug unit before moving or
cleaning and when not in use. ¥ Do not insert aerosol cleaners into or around the
This shredder contains sharp edges on the underside of the shredder head. Use caution when positioning the shredder head onto the basket.
shredder. Some agents may combust, causing seri- ous injury. ¥ Never use flammable synthetic oil, petroleum- based
or aerosol lubricants to oil the cutting blades. Some agents may combust, causing serious injury. Use only a recommended oil in a non-aerosol con- tainer. See "MAINTENANCE." ¥ Do not use this product if it or the cord has been
damaged in any way. ¥ Do not open the cover for any reason. Doing so can
expose you to dangerous voltages and will void your warranty. Power Cord Care ¥ Place power cord in an easily accessible position,
because it is the main disconnect switch. ¥ Do not place machine where adults, children or ani-
mals may walk on the cord. ¥ Do not rest anything on the power cord. ¥ If an extension cord is used, be sure that all prod-
ucts plugged into the extension cord do not exceed the extension cord ampere rating.
®

Cool-Down Cycle This shredder is protected with a special safety feature which prevents the motor from overheating with exten- sive use. When shredding is attempted beyond the machine's maximum running time, the shredder will automatically shut off its motor until it has cooled to an acceptable operating level. This is nor- mal and the shredder will return to operation after the cool-down or "off" period. See "Product Usage Guide" on front panel for maximum running time and related cooling "off" time.
This product features an auto-start sensor. This sensor will turn on the cut- ting blades whenever anything is inserted into the paper entry (while the power switch is in the AUTO position). For the safety of pets and children, we rec- ommend always moving the power switch to OFF and unplugging whenever the shredder is unattended or not in use.
Clearing a Jam If the shredder sheet capacity is exceeded or paper is not put in straight, a jam may result. See "Product Usage Guide" on front panel for maximum sheet capacity for your shredder. To clear a jam: 1. Move the power switch to the REVERSE (R) posi- tion. (NOTE: If waste basket is full, empty it before clearing jam.) The shredder will reverse the paper to clear the jam. 2. If the shredder jams in reverse, move the power switch to AUTO (I) and allow to run for about five seconds. If jam does not clear, move power switch to REVERSE (R) again and allow to run for about five seconds. Repeat this procedure until the jam is cleared. If necessary, use care to grasp the paper carefully and pull out to clear the jam. 3. Once the jam is cleared, move the power switch to AUTO (I) for continued shredding or OFF (O) if shredding is complete.
Do not attempt to shred paper clips or other hard materials (except staples) with this machine. Extensive use of paper clips or other hard materials will result in damage to the cutting sys- tem and will void the manufacturer's warranty. 3. Be sure power switch is in OFF (O) position. Plug shredder into proper power supply outlet. 4. Move power switch to AUTO (I) position. To clear the cutting blades, the shredder will "run" for about 1 second immediately after switching to AUTO (I). When the unit is turned on and in standby mode, the shredder is ready to be fed paper through the paper entry. (See "TROUBLESHOOTING" if red LED is lit.)
NEVER insert hands or fingers into paper entry as serious personal injury may result.
Do not exceed recommended sheet capacity (see "Product Usage Guide" on front cover of this manual). 5. Slide paper straight into paper entry until the shred- der automatically begins shredding. The shredder automatically stops a few seconds
MAINTENANCE Confetti cut shredders require regular (monthly) oiling of the cutting blades to maintain proper operation. Failure to oil the blades regularly could result in reduced sheet capacity performance, excessive noise during operation, paper jams and possibly shredder failure. We recommend using only Powershred Lubricant #35250 (available by contacting Fellowes) or a veg- etable-based oil (such as corn or canola) in a non- aerosol container with an extension nozzle.
after shredding is complete. Continue shredding as desired to a MAXIMUM
shredding time of 5-7 minutes. At this time, the machine MUST be allowed to "cool down" for a MINIMUM of 15 minutes. (See "Cool-Down Cycle" for more information.) If the shredder jams or shuts off before the maxi-
Never use flammable synthetic oil, petroleum- based, or aerosol lubri- cants to oil the cutting blades. Some agents may com- bust, causing serious injury.
mum shredding time, see "Clearing a Jam" section for further instructions. 6. Move power switch to OFF (O) position when shredding is complete. 7. Unplug power cord from outlet whenever shredder is unattended or not in use. 8. Check basket to see if it is full. If full, remove shred- der head and empty basket contents. Replace shredder head onto basket.
To oil the cutting blades: 1. From the top of the shredder, squeeze the recom- mended lubricant across the full width of the blades. 2. Move the power switch to AUTO (I) position and allow the blades to run at least 3 seconds. 3. Move the power switch to REVERSE (R) position and allow it to run for at least 3 seconds. 4. Repeat steps 2-3 above at least 3 times.

Australia Benelux Canada France Germany Italy Japan Poland United Kingdom
Tullamarine, Vic Vianen, NL Markham, Ont. Rennes, I-V Garbsen, Han. Camerano, AN Tokyo Warsaw Doncaster, S. Yorks.
© 2001 Fellowes Printed in China. Form No. 30117
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.