Instruction/ maintenance manual of the product 42-122-xx Extron electronic
Go to page of 28
A VT rac ® International/Universal Models Floor -mount Raceway with Modular AAP Connectivity for A/V , Data, and Power Installation Guide 68-1562-01 Rev .
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock.
Intr oduction A VT rac • Introduction 1 This manual describes the A VT rac ® components and provides instructions for installation. Low-profile Raceway System A VT rac is a low-profile raceway system designed to safely and discretely run power , data, and A/V cables from a wall to a table, podium, or other furniture.
Kit Contents A VT rac • Kit Contents 2 Box 1 The A VT rac Kit is shipped in two boxes. Box 1 • contains the track and ramp components. Box 2 • contains the connectivity box, the conduit and accessory components. Check the contents of each box to ensure all items are present.
Kit Contents A VT rac • Kit Contents 3 Box 2 Check the contents of each box to ensure all items are present. Checklist for contents of box 2 Connectivity box (1) with 6/32" nut (1) to secure AC power module 9.
Befor e Getting Started A VT rac • Before Getting Started 4 A VT rac can be installed before new carpeting is fitted or retr ofitted under pre-existing carpet. It can also be installed in new construction before the wall and carpeting is in place.
A VT rac • Before Getting Started 5 Conference Room AV Tr ac Cable Cub by MediaLink Controller Room Considerations Determine the A/V requir ements for the room. Extr on provides a complete range of AAPs that can be purchased separately to provide fully customizable central connectivity .
Befor e Getting Started, cont’d A VT rac • Before Getting Started 6 Almost everything you need to install your A VT rac system has been included. Y ou will need some basic tools and materials depending on the facility and requir ements. Y ou can visit www .
Installation A VT rac • Installation 7 Step 1: Floor By this point you must have decided exactly where the A VT rac will be installed, checked the contents of the kit, and gathered the tools that you will need. Extron r ecommends consulting a carpeting expert before r emoving the carpet.
Installation A VT rac • Installation 8 Step 2: W all Cut cable access hole in wall 2-2 Using a drill, box cutters and/or a saw , cut a 4" W x 1½" H (10.
Installation A VT rac • Installation 9 Step 3: T rack Measure and cut track 10.00" (25.4 cm) Connectivity (AAP) Box Rubber Strip Aluminum Cover T rac k 7'-2 " (2.184 m) 9.36" (23.77 cm) 8'-0 " (2.438 m) End Ramp Side Ramp Cut aluminum base track 3-1 Measure and cut the track pieces to the desir ed length.
Installation A VT rac • Installation 10 Step 3: T rack, cont’d Pre-drill holes to secur e connectivity box End Plate End Plate Co ve r Mounting Holes The end of the Connectivity Box with three mounting holes fa ces back to wa rds the track. 3-3 Remove the cover panel and end plates from the connectivity box.
A VT rac • Installation 11 Drill a 5/32 ” x 1 1/2” deep hole into concrete. Supplied Masonry Screws Drill into concrete and scr ew down track Screw side ramps to floor 3-6 W ith the provided masonry screws, secur e the track and ramps to the floor .
Installation A VT rac • Installation 12 Step 4: Connectivity Box By this point, the base track, side ramps and end ramps must be securely fastened to the floor .
Installation A VT rac • Installation 13 Step 5: Power Module (F) (D) (E) Receptacles for the AC power modules are available in Australian (F), universal (J), central European (D), and Fr ench (E) models. The Australian and Universal models are pr ovided with 24' of metal conduit, without wires (CO models).
Installation A VT rac • Installation 14 Step 5: Power Module cont’d 5-2 The AC power module must be positioned under the triple AAP socket that is closest to the track. Seat the power module on the stud in the connectivity box. Slide the power module side tabs into the slots on the side of the connectivity box.
Installation A VT rac • Installation 15 Step 6: AAPs At this point, the track, ramps and connectivitly box must all be securely in place, and the AC power module must be attached to the connectivity box and connected to an AC junction box.
Installation A VT rac • Installation 16 Step 7: Finishing Up At this point, the track and connectivity box must be secured to the floor , the electrical power must be connected, and the AAP sockets must be populated.
A VT rac • Installation 17 7-4 Glue or tape the carpet to the floor and side ramps. Refit carpet 7-5 Using the provided template, trim the wall baseboard to fit snugly ar ound the track.
Installation A VT rac • Installation 18 Step 7: Finishing up cont’d The installed A VT rac safely and discretely runs power , data, and A/V cables from a wall to a table, podium, or other furniture.
Refer ence Material A VT rac • Reference Material 19 Specifications General Power (pass-through) ................... 250 V AC, 50/60 Hz, 10 A (max.) Mounting options T rack system (track and ramps) Mountable on base flooring, beneath the finished carpet Connectivity box .
Refer ence Material, A VT rac • Reference Material 20 cont’d Connectivity box TOP VIEW End Ramp Side Ramp Aluminum T rack Connectivity (AAP) Box 9.36” (23.77 cm) 18.72” (47.55 cm) 10.00” (25.4 cm) 8’-0” (2.438 m) 2.68” (6.8 cm) AVTrac 480R 3.
A VT rac • Reference Material 21 SIDE VIEW TO P VIEW END VIEW 4.91" (12.47 cm) 3.55" (9.02 cm) 10.00" (25.4 cm) 10.00" (25.4 cm) 4.
Refer ence Material, A VT rac • Reference Material 22 cont’d Earth/Ground Live/Hot Phase/Active Neutral The Extron Universal AC Outlet allows a number of different AC plugs to be used in the A VT rac ™ , HSA, and Cable Cubby ™ devices.
A VT rac • Reference Material 23 Please consult the Extron W eb site (www .Extron.com) or catalog for a complete description of each item. T rack Accessories Accessory Part Number A VT rac 4 ' .
Refer ence Material, A VT rac • Reference Material 24 cont’d.
Extr on’ s W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of three years fr om the date of purchase.
A VT rac • Quick Installation Checklist Ex tron US A - We st Headquar te rs + 800 .6 33 .9 87 6 Insid e U S A / C anad a On ly +1 .7 14 .4 91 .1 50 0 +1 .7 14 .4 91 .1 51 7 FA X Ex tron US A - Eas t + 800 .6 33 .9 87 6 Insid e U S A / C anad a On ly +1 .
An important point after buying a device Extron electronic 42-122-xx (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Extron electronic 42-122-xx yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Extron electronic 42-122-xx - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Extron electronic 42-122-xx you will learn all the available features of the product, as well as information on its operation. The information that you get Extron electronic 42-122-xx will certainly help you make a decision on the purchase.
If you already are a holder of Extron electronic 42-122-xx, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Extron electronic 42-122-xx.
However, one of the most important roles played by the user manual is to help in solving problems with Extron electronic 42-122-xx. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Extron electronic 42-122-xx along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
