Instruction/ maintenance manual of the product ED335 EverFocus
Go to page of 18
1/3” CCD Indoo r 3-Axis Dual V oltage T rue Day/Night IR Dome Came ra Operation Instructions Model No. ED335 Please read this manual first for correct installation and operation. This manual should be re t ained for fu tur e reference. The information in this manual wa s current when published.
1 PRODUCT OVER VIEW ED335 is a new design IR Dome camera from Everfo c us. It incorporates breakthrough DSP technolog y to provide brilliant color images in well lit environmen ts.
2 Power supply pigtail Video test cable Accessory pack #2 containing t wo flush mounting clips DIMENSIONS.
3 SPECIFICA TIONS Pickup Device 1/3” SONY Super HAD CCD Video Format NTSC or P AL Scanning System NTSC: 525 TV lines, 60 fields/sec; P AL: 625 TV lines, 50 fields/sec. Picture Element 768 x 494 (NTSC); 752 x 582 (P AL) Horizontal Resolution 520 TV Lines Sensitivity 0 Lux (IR LED on) 0.
4 MAJOR P AR TS: NAMES AND FUNCTIONS Front View Side View 2. IR LEDs 4. Light sensor 1. Outer Base 6. Focus Adjust 8. Video Output 9. Power Input 3. Lens 5.
5 Back V iew 1. Base The camera unit sets in the dome base, when it is s hipp ed from the factory . This base is used for surface mounting, and is discarded fo r fl ush mounting. 2. IR LEDs 3. Lens The included vari-focal, DC iris lens allows manual adjustment of the field of view (zoom & focus).
6 7. Zoom Ring T o adjust the viewing angle, loosen t he zoom ri ng knob. T urn the ring toward <W> to Zoom out or <T> to Zoom in as necessary , and re-tighten when the a djustment is complete. 8. Video Output Please connect to the BNC connecto r of the cable from the DVR or monitor .
7 3-AXIS GIMBAL BRAC KET The 3-axis gimbal enables installers to easily moun t the camera on a wall or ceiling and then using the built in tilt and dual axis 180° twist, to adjust the viewing a n gle to the desired direction.
8 INST A LLA T I ON An ED335 camera may be mount ed in two ways: surface mount and flush mount. Select the one that meets your needs. Installation - Surface Mount 1. Paste the drilling template on the ceiling or wall. P le ase refer to the drilling template belo w .
9 4. Remove dome cover (4 captive hex head screws); re m ove inner base from outer base (4 Phillips head screws – retain these for later re-assembly). 5. Pull the cables to be connected to power and video ca bles into the outer base from the ceiling or wa ll.
10 7. Attach power and video cables from source to c ables from camera and push exce s s wire back into hole. 8. Insert inner base into outer base and se c ure using the 4 Phillips removed in the earlier step . Preposition camera so it is facing approximately in the desired direction.
11 10. Once the camera view is as desired, attach the cover to oute r base with the captive hex head screws..
12 Installation - Flush Mount 1. Paste the drilling template on the ceiling or wall. P le ase refer to the drilling template belo w . 2. Use the appropriate tool to drill the OUTER holes; carefully cut a lo ng the dashed circle to create a clearance hole for the inner base unit.
13 5. Unscrew the 4 Philips screws (retain f or future use) to detach the inner base from the o uter base. Set aside the outer base. 6. Screw the 2 spring tabs in the orientation shown t o the slots at both sides of the inner base using the 4 Philips head screws provided.
14 7. Atta c h power and video cables from source to cab les from camera and push excess wire ba ck i nto hole. Fold the spring tabs up. 8. Preposition camera so it is facing approximate ly in the desired direction. 9. Push the entire inner base into ceiling while holding the spring tabs with both hands.
15 10. The spring tabs will open automatically to support the camera against the ceiling. 1 1. Use the long Phillips pan head screws (x4) provided to screw the base to the ceiling.
16 12. Attach video test cable to test point on rear of camera modu le . Aim and focus the ca mera. Remove test cable. 13. Screw the cover back to the base with capt ive hex head screws.
17 Headquarters Of fice 12F, No.79 Sec. 1 Shin-Tai W u Road, Hsi-Chi, Taipei , Taiwan Tel: +886-2-26 982334 Fax: +886-2-2 6982380 Beijing office Room 609,T echnology Trade Bui lding.
An important point after buying a device EverFocus ED335 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought EverFocus ED335 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data EverFocus ED335 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, EverFocus ED335 you will learn all the available features of the product, as well as information on its operation. The information that you get EverFocus ED335 will certainly help you make a decision on the purchase.
If you already are a holder of EverFocus ED335, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime EverFocus ED335.
However, one of the most important roles played by the user manual is to help in solving problems with EverFocus ED335. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device EverFocus ED335 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
