Instruction/ maintenance manual of the product IP DSLAM Ericsson
Go to page of 20
EDN312 Installation Guide Ethernet DSL Access IP DSLAM.
EDN312 Installation Guide Ethernet DSL Access IP DSLAM . ii 1/1531-HSD 101 41 Uen A 2004-01-30 Copyright Ericsson AB - 2004 All Rights Reserved Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner.
. 1/1531-HSD 101 41 Uen A 2004 -01-30 iii Contents 1 Introduction 1 1.1 Revision History 1 2 Environmental and Space Requirements 2 3 Cabling 4 3.1 Cabling of Subscriber Lines 4 3.1.1 Cabling Lines 4 3.1.2 Wiring EDGE Connectors 5 3.2 Cabling of Ethernet Connections 8 4 Mounting the IP DSLAM 9 5 Verifying the Installation 10 5.
.
Introduction 1/1531-HSD 101 41 Uen A 2004 -01-30 1 1 Introduction This guide describes how to install t he Ethernet DSL Access (EDA) IP DSLAM EDN312. The guide is intended for installation and maintenance personnel. An overview of the installation process of a complete Access Domain is described in the Access Domain Installation Guid e .
Environmental and Space Requirements 2 1/1531-HSD 101 41 Uen A 2004 -01-30 2 Environmental and Space Requirements The 12-line IP DSLAM (EDN312) complies with the following standards regarding storage, transportation and operation. The operation category is also designated stationary in-use at weather-protected locations.
Environmental and Space Requirements 1/1531-HSD 101 41 Uen A 2004 -01-30 3 The distance between the IP DSLAMs must be at least 20 mm so that an IP DSLAM can be dismounted without interfering with the adjacent IP DSLAMs.
Cabling 4 1/1531-HSD 101 41 Uen A 2004 -01-30 3 Cabling 3.1 Cabling of Subscriber Lines Before the IP DSLAM is mounted the connections between the Line MDF and the Exchange MDF have to be rewired. The wires are disconnected, and then reconnected through typically a Broadband MDF and the EDA System according to planning.
Cabling 1/1531-HSD 101 41 Uen A 2004 -01-30 5 3.1.2 Wiring EDGE Connectors It is recommended to follow the “Best practice” wiring procedure when wiring the EDGE connectors. The EDGE connector can be mounted by using a Tool Kit. The kit consists of a wiring bracket-tool and an LSA+ inserter-tool.
Cabling 6 1/1531-HSD 101 41 Uen A 2004 -01-30 Figure 4 Mounting the EDGE Connectors Strip approximately 20 cm off the new cable and tie it up with a cable tie to the existing cable as illustrated in Figure 5 on page 7. Alternatively, make a loop around the cable guide.
Cabling 1/1531-HSD 101 41 Uen A 2004 -01-30 7 Figure 5 Tie Up the New cable Connect and cut the wires (one action using the KRONE LSA+ Insertion- Tool S, see Figure 6 on page 7) by placing the Insertion tool above the slit (place the cutting end towards the connector’s center), and firmly press towards the connector.
Cabling 8 1/1531-HSD 101 41 Uen A 2004 -01-30 Figure 7 Tie Up and Label the EDGE Connectors 3.2 Cabling of Ethernet Connections The EDN312 IP DSLAM is connected to the network with cat.
Mounting the IP DSLAM 1/1531-HSD 101 41 Uen A 2004 -01-30 9 4 Mounting the IP DSLAM The illustration below shows how to mount the EDN312 after the subscri ber lines, exchange lines through the EDGE connector have been pulled. The EDGE connector is removed from the bracket-tool and inserted in the rear of the IP DSLAM.
Verifying the Installation 10 1/1531-HSD 101 41 Uen A 2004 -01-30 5 Verifying the Installation The purpose of the verification is to ensure the following: • No errors in the rewiring of the subscrib.
Verifying the Installation 1/1531-HSD 101 41 Uen A 2004 -01-30 11 5.2 V erification with the Local Craft T ool The LCT can be used without a connection to PEM or to any backbone network as described in section sect ion Error! Reference source not found.
Verifying the Installation 12 1/1531-HSD 101 41 Uen A 2004 -01-30 2. Copy 24 configuration files with line configurations from the LCT tool to the ECN320 flash disk. 3. Restart the embedded IP DSLAMs by using the Command Line Interface (CLI) 4. Test the ADSL lines by connecting a CPE modem to each line one at a time.
Verifying the Installation 1/1531-HSD 101 41 Uen A 2004 -01-30 13 This method is similar to activating real subscribe rs. In order to use this method the following preconditions have to be fulfilled: .
Reference List 14 1/1531-HSD 101 41 Uen A 2004-01-30 Reference List System Overview, 1/1551-HSC 901 26/4, Ericsson AB 2004 PEM User’s Guide, 1553-AOM 901 018/3, Ericsson AB 2004 EDN312 User’s Guid.
.
Ericsson AB Ericsson AB - 2004 All Rights Reserved www.ericsson.com 1/1531-HSD 101 41 Uen A 20 04-01-30.
An important point after buying a device Ericsson IP DSLAM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ericsson IP DSLAM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ericsson IP DSLAM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ericsson IP DSLAM you will learn all the available features of the product, as well as information on its operation. The information that you get Ericsson IP DSLAM will certainly help you make a decision on the purchase.
If you already are a holder of Ericsson IP DSLAM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ericsson IP DSLAM.
However, one of the most important roles played by the user manual is to help in solving problems with Ericsson IP DSLAM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ericsson IP DSLAM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
