Instruction/ maintenance manual of the product MHVFB10LP Enerco
Go to page of 16
Installation instructions and Owner’s Manual 1 ENER CO GR O UP , INC., 4 560 W . 1 60 TH ST ., CLEVELAND, OHIO 4 4 1 3 5 · 2 1 6-9 1 6-3 000 W ARNING: If the information in this manual is not followed exactly , a fire or explosion may result causing property damage, personal injury , or loss of life.
2 Installation instructions and Owner’s Manual This appliance may be installed in an aftermarket* permanently manufactured (mobile) home, where not prohibited by local codes.This appliance is only for use with the type of gas indicated on the rating plate.
Installation instructions and Owner’s Manual 3 Product Features Figure 1 SAFETY DEVICE This heater has a pilot with an Oxygen Depletion Sensor (ODS) safety shut off system. The ODS/pilot shuts off the heater if there is not enough fresh air . IGNITION SYSTEM PIEZO: MHVFB10LP – The heater is equipped with a piezo manual ignitor .
4 Installation instructions and Owner’s Manual 1. Find the volume of the space by multiplying room length x width x height. Example: S pace size 18ft (length) x 18f t. (width) x 8f t. (height) = 2592 If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the sp ace.
Installation instructions and Owner’s Manual 5 Code NFP A 54/ ANSI Z223.1, Section 5.3, Air for Com- bustion and V entilation for required size of ventilation grills or ducts.
6 Installation instructions and Owner’s Manual Figure 5 Removing Front Panel of Heater 1. Remove three screws on bottom front of front panel. 2. Pull bottom of front panel forward, then down (see figure 6) Figure 6 Attaching Mounting Bracket to W all Use holes on each end of mounting bracket to attach bracket to wall.
Installation instructions and Owner’s Manual 7 1. Locate two horizontal slots on back pane of heater (see figure 19). 2. Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket. Figure 9 Installing Bottom Mounting Screws 1.
8 Installation instructions and Owner’s Manual run correctly . IMPORT ANT : Hold pressure regulator with wrench when connecting it to gas piping and/or fittings. CHECKING GAS CONNECTIONS W ARNING: T est all gas piping and connections for leaks after inst alling or servicing.
Installation instructions and Owner’s Manual 9 Figure 13 Figure 14 FOR YOUR SAFETY READ BEFORE LIGHTING W ARNING: If you do not follow these instructions exactly , a fire or explosion may result causing property damage, personal injury or loss of life.
10 Installation instructions and Owner’s Manual Figure 16 CAUTION: Do not try to adjust heating level by using equipment shutoff valve. W ARNING: When running heater, set control knob at “LO” or “HI” locked positions.
Installation instructions and Owner’s Manual 11 Make sure grille guard is in place before running heater . If screen or grille guard is removed for servicing it must be replaced prior to operating the heater . W ARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.
12 Installation instructions and Owner’s Manual TROUBLESHOOTING NOTE: All troubleshooting items are listed in order of operation and likely occurrence. W ARNING: Only a qualified service person should service and repair heater . CAUTION: Never use a wire needle, or similar object to clean ODS/pilot.
Installation instructions and Owner’s Manual 13 TROUBLESHOOTING W ARNING: If you smell gas: • Shut off gas supply • Do not try to light any appliance • Do not touch any electrical switch; do not use any phone in your building • Immediately call you gas supplier from a neighbor’s phone.
14 Installation instructions and Owner’s Manual REPLACEMENT P ARTS Note: use only original replacement parts. This will protect you warranty coverage for parts replaced under warranty . P ARTS UNDER W ARRANTY Contact authorized dealer from whom you pur- chased this product.
Installation instructions and Owner’s Manual 15 ITEM P A R T N O . DESCRIPTION QTY . MHVFB10LP 1 70300 Cabinet assembly 1 1-1 70595 Cabinet T op Panel 1 1-2 70592 Cabinet Right Panel 1 1-3 70593 Cab.
16 Installation instructions and Owner’s Manual ENER CO GR OUP , INC., 4 560 W . 1 60TH ST., CLEVELAND, OHIO 44 1 3 5 216-881-5500 T oll Fr ee Number 1-800-2 5 1-000 1 www .mrhea ter .com Mr . Heater is a r egistered tr ademarks of Ener co Gr oup, Inc.
An important point after buying a device Enerco MHVFB10LP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enerco MHVFB10LP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enerco MHVFB10LP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enerco MHVFB10LP you will learn all the available features of the product, as well as information on its operation. The information that you get Enerco MHVFB10LP will certainly help you make a decision on the purchase.
If you already are a holder of Enerco MHVFB10LP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enerco MHVFB10LP.
However, one of the most important roles played by the user manual is to help in solving problems with Enerco MHVFB10LP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enerco MHVFB10LP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
