Instruction/ maintenance manual of the product 34942G Electrolux
Go to page of 28
34942G Gas hob Operating Instructions GB.
2 Important Safety Information Y ou MUST r ead these warnings car efully befor e installing or us ing the hob. If you need assistance, contact our Customer Care Department on 087 05 350 350 Installation This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards.
3 When using the hob for a long period of time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water . Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use.
4 Contents Important Safety Information .................................................................... 2 Instructions for the User .............................................................................. 6 Description of the Hob ..........
5 This appliance is manufactured accor ding to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition.
6 1. Hob T op 2. Rapid Burner 3. Semi-rapid Burners 4 . Triple-cr own Burner 5. Auxiliary Burner 6. Control knob for back left burner (semi-rapid) 7. Control knob for back right burner (semi-r apid) 8. Control knob for front right burner (auxiliary) 9 .
7 Operation Burner minimum m aximum diameter diameter Triple-crown (ultra-rapid) 160 mm 260 mm Lar ge (r apid ) 160 mm 240 mm Medium (semi-rapid) 120 mm 220 mm Small (auxiliary) 80 mm 160 mm As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering.
8 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed mor e easily than if it is left to cool.
9 Something Not Working? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre.
10 Service and Spar e Part s When you contact the Service Centre, they will need the following information: 1. Y our name, address and post code. 2. Y our telephone number 3. Clear and concise details of the fault 4 . The model and the serial number (see rating label on the back of this instruction booklet) 5.
11 Guarantee Conditions Standar d guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG- Electrolux appliance or any part thereof is proved t.
12 OVERALL DIMENSIONS Width: 860 mm Depth: 500 mm Height: 8 8 m m Weight: 1 6 K g CUT OUT DIMENSIONS Width: 830 mm Depth: 470 mm Thickness: 3 0 m m SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) .
13 Burner Dia. Tap By-pass 1/100 mm Auxiliary 28 Semi-rapid 32 Rapid 40 Triple-Crown 5 6 Aeration adjustment none BURNER RAPID S E M I-RAPID AUXILIARY T R IP L E (large) ( m edium) ( small) CROWN POSITION MA X MI N MA X M IN M AX MI N MA X MI N NOMINAL THERMAL POWER (kW) 3 .
14 Important safety r equir ements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B .
15 CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standar ds.
16 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 On the end of the shaft, which includes the G 1/2" threaded elbow , adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Scr ew the parts together without using excessive force.
17 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboar d or drawer If the hob is to be installed above a cupboard or dr awer it will be necessary to fit a heat resistant boar d below the base of the hob on the underside of the work surface.
18 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 12 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated.
19 Building in Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in or der to prevent spillage near the hob seeping into the cabinet below .
20 Electrical connection s Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
21 P ermanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the requir ed load in compliance with the curr ent electric regulations.
22 Fault Finding Preliminary Electrical Sy stems Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check.
23 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on ý (Ohms) x 1 scale and adjust zero if necessary . — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 ý (Ohm), check all earth wires for continuity and all contacts are clean and tight.
24 Check gas supply at burner Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ig.
25 Commis sioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedur e below . 1) T urn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
26 Conver sion fr om Natur al Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit.
27.
35690-3001 03 /05 Grafiche MDM - Forlì From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use.
An important point after buying a device Electrolux 34942G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux 34942G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux 34942G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux 34942G you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux 34942G will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux 34942G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux 34942G.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux 34942G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux 34942G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
