
Operator's Guide


Before operating this machine, please read the Operator’s Guide and Product Safety Guide thoroughly. The 3M™ Multimedia Projectors are designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, or different voltages have not been tested and could damage the projector peripheral equipment and/or create a potentially unsafe operating condition. 3M Multimedia projectors are designed to operate in a normal office environment.
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the projector.
void the product warranty.


This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.
FEATURES
PREPARATIONS Your projector should come with the items shown below. Check to make sure that all the items are included. Contact your dealer if anything is missing.

MP8765 Projecteur multimedia - Guide de Securite de Produit MP8765 Multimedia-Projektor - Sicherheitsanleitung des Gerats MP8765 Proyector de Multimedia - Guía de Seguridad del Producto MP8765 Proiettore Multimediale - Guida di Sicurezza del Prodotto MP8765 Multimedia Projector - Veiligheidgids op Product MP8765 Projector dos Multimedia - Guia da Seguranca de Produto MP8765 Multimedia Projektør- Bruksabvisning for Produktsakerhets


Connect your computer, VCR and/or other devices you will be using to the projector.
(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.


ON/OFF Switch 14

STANDBY/ON 14
RGB 15
RGB SEARCH
AUTO 19
ASPECT
AUTO BLANK
ASPECT 22
BLANK 22
PAGE UP VOLUME MAGNIFY
HOME
VOLUME 17
ON
MAGNIFY 21
END MUTE PAGE DOWN
FRANÇAIS T
OFF
MUTE 17
KEYSTONE FREEZE
FREEZE 21
KEYSTONE 20
KEYBOARD 24
MENU POSITION
POSITION 18
MENU 23
cursor buttons
ENTER
, , , 23
ESC RESET
RESET 2
ESC 23
ENTER 23

You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection. The adjustment range of the elevator feet is 0 to 9 degrees.
2 Raise or lower the projector to the desired height and then release the elevator buttons When you release the elevator buttons, the elevator feet will lock into position.
3 As necessary, you can also finely adjust the height of the projector by twisting the elevator feet by hand

Refer to the illustrations and tables below to determine the screen size and projection distance.
The values shown in the table are calculated for a full size screen
(MP7650: 800x600 pixels / MP7750: 1024x768 pixels). a:Distance from the projector to the screen (±10%) b:Distance from the lens center to the bottom of the screen (±10%) c:Distance from the lens center to the top of the screen (±10%)
Top view
If 4:3 aspect ratio
The screen
Top view
If 16:9 aspect ratio

Devices You Can Connect to the Projector (Refer to this section for planning your device configuration to use for your presentation.)
Display monitors 12

Laptop computers 10
VCRs 11
Desktop computers 10

Refer to the table below to find out which projector port and cable to use for connecting a given device. Use this table for determining which cables to prepare.





CR/ RR CB/ PB Y
CR/ RR CB/ PB Y
Desktop computer

MOUSE cable


CR/ RR CB/ PB Y
If using a component video connection
If using an audio/video connection
Connecting to a VCR

CR/ RR CB/ PB Y
COMPONENT cable

Connecting to a Display Monitor
1 RGB IN 2
AUDIO IN
R L / (MONO) VIDEO IN
S-VIDEO IN
A
CR/ RR CB/ PB Y
RGB OUT CONTROL
USB
A
RGB OUT RGB IN
Display monitor
RGB cable

Putting batteries into the remote control unit

1 Remove the battery cover Slide back and remove the battery cover in the direction of the arrow.
Close the battery cover Replace the battery cover in the direction of the arrow and snap it back into place.

approximately 3 meters approximately 3 meters


Precautions Connect all devices to be used to the projector prior to turning on the power. 12 8 ~
1 Make sure that the power cord is firmly and correctly connected to the projector and outlet
RGB SEARCH
ASPECT
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
2 Turn on the projector's power Set the power switch to [ | ] (ON). The projector will go to STANDBY mode and the POWER indicator will light to solid orange.
OFF
KEYSTONE FREEZE
Control panel
LANP
TENP
POWER
STANDBY/ON INPUT KEYSTONE RESET
STANDBY/ON INPUT KEYSTONE RESET
LANP TENP POWER
LANP TENP POWER
KEYSTONE RESET

NOTE
4 Remove the lens cap The picture is projected.
power switch · POWER indicator

Using the projector's control panel
If selecting RGB input Press the RGB button Press this button to toggle between the devices connected to RGB IN 1 and 2. As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2. Select the signal you wish to project.
Press the INPUT button As illustrated below, each time you press the INPUT button, the projector switches between its input signal ports. Select the signal you wish to project.
RGB
RGB IN 1 RGB IN 2
RGB IN 1 RGB IN 2 VIDEO IN
If selecting video input Press the VIDEO button Press this button to toggle between the devices connected to VIDEO IN, S- VIDEO IN and COMPONENT VIDEO. As illustrated below, each time you press the VIDEO button, the projector switches between VIDEO IN, S-VIDEO IN and COMPONENT VIDEO. Select the signal you wish to project.
VIDEO IN S-VIDEO IN
COMPONENT VIDEO
6 Use the zoom ring to adjust the screen size
7 Use the focus ring to focus the picture

1 Press the STANDBY/ON button (control panel or remote control) The message "Power off?" will appear on the screen for approximately 5 seconds.
RGB SEARCH
STANDBY/ON
ASPECT
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
OFF
2 Press the STANDBY/ON button again (control panel or remote control) Press the STANDBY/ON button again while the "Power off?" message is visible. The projector lamp goes off and starts cooling down. The POWER indicator blinks orange while the lamp cools down. (Pressing the STANDBY/ON button while the POWER indicator is blinking orange has no effect.) The system goes into the STANDBY mode after cooling down and the POWER indicator stops blinking orange and then lights to solid orange.
MENU POSITION
ENTER
ESC RESET
STANDBY/ON
Control panel
3 Check that the POWER indicator stops blinking and lights to solid orange. Switch the power switch to [O] (OFF).
TENP
POWER
STANDBY/ON INPUT KEYSTONE RESET
STANDBY/ON INPUT KEYSTONE RESET
LANP TENP POWER

LANP TENP POWER
4 Confirm that the POWER indicator has gone off and then attach the lens cap. When the projector has completed powering down, the POWER indicator will go off.
power switch · POWER indicator

STANDBY/ON 1 Press the VOLUME button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume.
RGB SEARCH
ASPECT
AUTO BLANK
VOLUME VOLUME
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
OFF
KEYSTONE FREEZE
2 Press the , buttons to adjust the volume Press the VOLUME button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)
ENTER
ESC RESET
VOLUME
Press this to increase the volume
Press this to decrease the volume
1 Press the MUTE button As illustrated on the right, a dialog will appear on the screen indicating that you have muted the sound. Press the VOLUME button to close the dialog. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.) Press the MUTE button again to restore the sound.
RGB SEARCH
ASPECT
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
OFF
KEYSTONE FREEZE
VOLUME
MENU POSITION
MUTE MUTE
ENTER
ESC RESET

1 Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position.
STANDBY/ON
ASPECT
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
POSITION
OFF
KEYSTONE FREEZE
POSITION
MENU POSITION
ENTER
2 Use the , , , buttons to adjust the position When you want to initialize the position, press the RESET button during adjustment. Press the POSITION button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.) This function is only available for RGB IN 1/2 input.

RGB SEARCH
STANDBY/ON
ASPECT
AUTO BLANK
Automatic Adjustment for RGB Input
PAGE UP VOLUME MAGNIFY
HOME
ON
Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE) and horizontal size (H. SIZE) are automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting.
OFF
KEYSTONE FREEZE
MENU POSITION
ENTER
ESC RESET
Automatic Adjustment for Video Input
The signal type best suited for the respective input signal is selected automatically. This feature is available only if VIDEO is set to AUTO in the INPUT menu.
The automatic adjustment operation requires approximately 10 seconds. Also, please

1 Press the KEYSTONE button As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion.
STANDBY/ON
RGB SEARCH
ASPECT
AUTO BLANK
KEYSTONE
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
OFF
KEYSTONE FREEZE
2 Use the , buttons to select the direction of distortion to correct ( / )
ENTER
ESC RESET
3 Use the , buttons to correct the distortion Press the KEYSTONE button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)

1 Press the MAGNIFY (ON) button The projector enters MAGNIFY mode.
ON
STANDBY/ON
RGB SEARCH
ASPECT
AUTO BLANK
2 Press the POSITION button, then use the , , , buttons to select the area to enlarge and then press the POSITION button again to confirm your selection
HOME
ON
END MUTE PAGE DOWN
OFF
KEYSTONE FREEZE
POSITION POSITION
MENU POSITION
ENTER
ESC RESET
3 Press the , buttons to zoom in and out of the selected area. Press the MAGNIFY (OFF) button to exit MAGNIFY mode and restore the screen to normal. (The projector will also automatically exit MAGNIFY mode if there is a change in the input signal's state.)
The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.
1 Press the FREEZE button The [II] icon appears and the screen will freeze at the current image. Press the FREEZE button again and the [ ] appears as the projector exits FREEZE mode.
HOME
ON
END MUTE PAGE DOWN
OFF
▲
KEYSTONE FREEZE
MENU POSITION
NOTE

1 Press the SEARCH button When you press the SEARCH button, the projector begins searching for input signals. If it detects an input signal, the search will cease and the projector will project the detected signal. If the projector is unable to find an input signal at any of its ports, it will return to the state it was in prior to the search.
RGB SEARCH
ASPECT
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
OFF
SEARCH RGB IN 1 RGB IN 2 VIDEO IN
KEYSTONE FREEZE
S-VIDEO IN COMPONENT VIDEO
SELECTING THE ASPECT RATIO
1 Press the ASPECT button
STANDBY/ON
RGB SEARCH
ASPECT
ASPECT
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
RGB IN 1, RGB IN 2, COMPONENT VIDEO (HDTV signals : 1125i (1035i/1080i), 750p)
KEYSTONE FREEZE
4:3 16:9
VIDEO IN, S-VIDEO IN, COMPONENT VIDEO (Non-HDTV signals : 525i, 525p,625i)
MENU POSITION
4:3 16:9 SMALL
ENTER
ESC RESET
TEMPORARILY BLANKING THE SCREEN
Press the BLANK button The input signal screen is shut off, and a blank screen appears. You can set the blank screen using the menu (from the SCREEN menu, select BLANK). Press the BLANK button again to remove the blank screen, and return to the input signal screen.
RGB SEARCH
ASPECT
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
OFF
KEYSTONE FREEZE
BLANK
MENU POSITION

1 Press the MENU button The menu display appears on the screen. The projector has the following menus: MAIN, PICTURE 1, PICTURE 2, INPUT, SCREEN, and OPTION. Select a menu using the / buttons. The current settings of the items that can be manipulated via the selected menu appear.
STANDBY/ON
RGB SEARCH
ASPECT
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
OFF
KEYSTONE FREEZE
2 Select a menu using the / buttons, then press the or ENTER button. The display of the selected menu appears. [ex. Adjusting SHARPNESS] Use the / buttons to select PICTURE 1, then press the or ENTER button.
ENTER
ESC RESET
MENU
MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT
–1 +1 –1 +1 –1
: SELECT
3 Select an item using the / buttons, then press the or ENTER button. The operation display of the selected item appears. To adjust a numerical value, press the or ENTER button again to switch to the single menu (small display showing only the operation display area). [ex. Adjusting SHARPNESS] Use the / buttons to select SHARPNESS, then press the or ENTER button.
MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
COLOR BAL R COLOR BAL B
SHARPNESS
COLOR
TINT
ENTER
: SELECT
4 Press the / buttons to adjust the level. Press the MENU button to hide the menu and finish your operation. Alternatively, press the or ESC button to return to the previous display. [ex. Adjusting SHARPNESS] Use the / buttons to adjust the SHARPNESS.

This device has 6 separate menus: MAIN, PICTURE 1, PICTURE 2, INPUT, SCREEN, OPTION. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.
button. Menu selection : Choose a menu name using the
MENU
button, and press the button or the ENTER button. Item selection : Choose an item using the
button, and press the button or the ENTER button. Return menu to last previous screen: Press the button or the ESC button. Execution of settings and/or adjustments: Operate by using the
button. (For further details, read the explanation for each separate menu.) Initialization of settings and/or adjustments: During operation, press the RESET button.
(Note that items whose functions are performed simultaneously with the operation of clock phase, language selection, automatic adjustment, etc., cannot be initialized.) End menu operations: Press the MENU button, or do not perform any operation for
several seconds.
MAIN Menu
MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
BRIGHT CONTRAST ASPECT PICT. POSIT. GAMMA MIRROR LANGUAGE
With the MAIN menu, the seven items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.

16:9 At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input: 4:3
SMALL • The SMALL picture may not be displayed correctly with certain input signals.

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT
With the PICTURE 1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.
PICTURE1 Menu

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
V POSITION H POSITION H PHASE H SIZE OVER SCAN
With the PICTURE 2 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.
PICTURE2 Menu

Small • If the horizontal size adjustment is excessive, the image may not be displayed correctly. In such a case, initialize H SIZE with the RESET button.
SMALL • It is recommended to select SMALL to avoid flicker at the lower part of the picture.

INPUT Menu
MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
AUTO VIDEO HDTV SYNC ON G
EXECUTE
With the INPUT menu, the four items shown in the Table below can be performed. With inputting of RGB IN 1 and RGB IN 2 signals, the horizontal and vertical frequencies of the signals will be displayed on the initial screen of the INPUT menu. Perform each operation in accordance with the instructions in the Table.
INPUT Menu
Item Description
Select Mode of Signal Type (for VIDEO/S-VIDEO): AUTO
PAL
SECAM
NTSC4.43
1035i • If the selected HDTV mode is incompatible with the input signal, the picture may be distorted.
TURN OFF Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode allows reception of SYNC on G. • In the SYNC ON G mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and turn SYNC ON G off, and then reconnect the signal.

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
BLANK START UP MyScreen MyScreen Size MyScreen Lock
With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.
Item Description
. . The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the “Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)). MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s). Option screens: Various colored non-patterned (plain) screens displayed within the Menus. • The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color screen several minutes after being displayed.
BLANK
TURN OFF The START UP Screen may be voluntarily selected. The START UP Screen is displayed when no signal has been inputted, or when spec signals are being inputted. MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s). TURN OFF: A non-patterned (plain) blue color screen. • The MyScreen and the ORIGINAL Screen will each change to the BLANK Screen several minutes after being displayed.
START UP
Registration of MyScreen: When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen and the START UP Screen is displayed. When operations are performed in accordance with this Menu, one can “cut” and register desired screens from among the received images within the display. 1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the picture becomes static (no longer moves), and a frame for picture cutting, as well as the message that follows below, appear. Please press the button when the screen you want to register is currently being displayed. 2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET) button will eliminate the static state of the picture, and operations can be performed again from operation 1. The frame can be moved using the
buttons. After designating the screen you want to register, pressing the ENTER button will initiate screen registration. The registration process takes approximately 1 minute to complete. 3. When the registration has been completed, the screen of the registered MyScreen, plus the message, “MyScreen registration is finished,” will be displayed for several seconds, after which the operation is terminated.
FULL
Invalidation of MyScreen registration function: TURN ON
TURN OFF When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in this way, one can prohibit rewrites (“writeovers”) of the MyScreen.
MyScreen ORIGNAL

OPTION Menu
MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
VOLUME AUTO OFF WHISPER LAMP TIME FILTER TIME
With the OPTION menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.
OPTION Menu
Item Description
(DISABLE: 0 min.) The system automatically enters the standby mode if no signal is received within the set time. This function is inactive when DISABLE (0 min.) is selected.
Short (Min. 1 min.)
WHISPER When WHISPER is selected the WHISPER mode is activated. In the WHISPER mode, acoustic noise and screen brightness are reduced.
Refer to FILTER TIME: This function displays the total time the air-filter has been used since new. Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]: Depress the RESET button for at least 3 seconds while lamp time is being displayed. The reset menu will then appear. After you replace the filter, select RESET on the menu with the button. DEFAULT
Low

You can use the remote control as a simplified mouse or keyboard.
STANDBY/ON
1. Turn off the projector and PC power, and connect the projector’s CONTROL terminal to the computer via the mouse cable. 2. If a USB cable is connected, disconnect it. If a USB cable is connected, the USB control function is given priority, and mouse control from the CONTROL terminal will not function. 3. Turn on the projector power, then the computer. The functions in the table below can be controlled. If you have difficulty with control, restart the computer (either from the software or by pressing the restart button).
AUTO BLANK
PAGE UP VOLUME MAGNIFY
HOME
ON
END MUTE PAGE DOWN
OFF
KEYSTONE FREEZE
Available Functions Remote Control Operation
Move Pointer Use buttons
Left click with mouse Press ENTER button
Right click with mouse Press RESET button
USB Mouse/Keyboard Control
Available Functions Remote Control Operation
Move Pointer Use buttons
Left click with mouse Press ENTER button
Right click with mouse Press RESET button
Press keyboard’s HOME key Press HOME button
Press keyboard’s END key Press END button
Press keyboard’s PAGE UP key Press PAGE UP button
Press keyboard’s PAGE DOWN key Press PAGE DOWN button
Press keyboard’s ESC key Press ESC button

Before replacing the lamp, check the serial number of your separately sold replacement lamp bulb (78-6969-9599-8 for MP7650 / 78-6969-9635-0 for MP7750), then contact your local dealer. Before replacing the lamp, turn off the power, and unplug the power cord, then wait at least 45 minutes, in order to ensure that the lamp is properly cooled. Removing the lamp bulb while it is still hot could cause burns, or cause the lamp bulb to burst.


All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" and "Regarding the Indicator Lamps" for details.)
1 Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes, and prepare a new lamp.
5 Insert the new lamp, and tighten the 1 screw firmly to lock it in place • Also steadily push the opposite side of the screwed side of the lamp into the unit.
2 After making sure that the projector has cooled adequately, slowly flip over the projector, so that the bottom is facing up
6 Replace the lamp cover, and tighten the 2 screws firmly to lock it in place
4 Unscrew the 1 screw, and slowly pull out the lamp by the handle • Be careful not to touch the inside of the lamp case.
8 Turn on the projector power, and using the menu, reset the lamp timer • To reset the lamp timer, from the OPTION menu, select LAMP TIME.
Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power
ON again. If the LAMP indicator is still red, replace the lamp.


The air filter should be cleaned about every 100 hours. If the LAMP indicator and TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned. (See "Related Messages" and "Regarding the Indicator Lamps" for details.)

2 Apply a vacuum cleaner to the top of the air filter cover to clean the air filter
3 Turn on the projector, and use the menu to reset the filter timer • To reset the air filter timer, from the OPTION menu, select FILTER TIME.

Replacing the air filter
If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please contact your local dealer, after confirming the serial number of your separately sold replacement air filter (78-8118-9055-3).
1 Turn off the projector, and unplug the power cord. Prepare a new air filter (one specified for your projector)
3 Insert the new filter, and replace the filter cover
4 Turn on the projector power, and using the menu, reset the filter timer • To reset the lamp timer, from the OPTION menu, select FILTER TIME.

Caring for the inside of the projector : In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years. Never try to care for the inside of the unit yourself. Doing so is dangerous.
Caring for the lens : Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand.
Caring for the cabinet and remote control transmitter : Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

Related Messages
When the unit's power is ON, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below.
CHANGE THE LAMP AFTER REPLACING LAMP,
Lamp usage time is approaching 2,000 hours. (Note 2) Preparation of a new lamp, and an early lamp change, is recommended. After you have changed the lamp, please be sure to reset the lamp timer.
RESET THE LAMP TIMER.
Lamp usage time is approaching 2,000 hours. A lamp change within
hours is recommended. (Note 2) When lamp usage reaches 2,000 hours, the power will automatically be turned OFF. Please change the lamp by referring to “THE LAMP” in Vol.1 (Basic). After you have changed the lamp, please be sure to reset the lamp timer.
AFTER
hr.
As lamp use has reached 2,000 hours, the power will soon be automatically turned OFF. (Note 2) Please immediately turn the power OFF, and follow the instructions in the “THE LAMP” section of the separate booklet, Vol.1 (Basic). After you have changed the lamp, please be sure to reset the lamp timer.
RESET THE LAMP TIMER. THE POWER WILL TURN OFF
AFTER 0 hr.
A note of precaution when cleaning the air filter. After cleaning the filter, operate FILTER TIME of the OPTION Menu, and perform reset of the filter timer.
RESET THE FILTER TIMER.
There is no input signal. Please confirm the signal input connection, and the status of the signal source.
ON
The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please confirm the specs for this unit or the signal source specs.
ON
NOTES
reappeared every time the power is turned ON. Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of
usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped with an automatic shut-down function, such that the power will automatically be turned OFF when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this unit.

Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the Table below. Please respond in accordance with the instructions within the Table.
LAMP indicator
TEMP indicator Description
(Not lighted) The STANDBY mode is set
Flashing of the green lamp Turned OFF Turned OFF The unit is warming up. Please wait.
The green lamp is lighted Turned OFF Turned OFF The unit is in an ON state. Ordinary operations may be performed.
Flashing of the orange lamp Turned OFF Turned OFF The unit is cooling down. Please wait.
The unit is cooling down. Please wait. A certain error has been detected. Wait until the POWER indicator lamp has finished flashing, and then perform the proper response measure using the item descriptions below as reference.
red lamp - -
The lamp does not light. There is a possibility that the interior portion has become heated. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please confirm whether or not there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please change the lamp.
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed (attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.
The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please make confirmation that no foreign matter has become caught in the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please confirm whether or not there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.
The red lamp is
The red lamp is
There is a possibility that the interior portion has become overcooled. Please use the unit within the usage temperature parameters (0°C to 35°C). After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.
with the red lamp
This is a notification that it is time to clean the filter.
After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform
with the red lamp
reset of the FILTER TIME.
When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF, and the indicator lamps may also be turned OFF. Press the “
” (power OFF) side of the main power switch, and wait for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently
cooled down.

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.
The main power source is not ON. Turn on the main power.
3, 14 The electrical power cord is not plugged in. Correctly connect the power cord.
Be sure to press the “O” (power OFF) side of the main power switch, and leave this OFF for approximately 20 minutes. After the unit has sufficiently cooled down, turn ON the power source.
Power does not come ON
The main power source has been interrupted during operation, such as by a power outage (blackout), etc.
The input changeover settings are mismatched.
Select the input signal, and correct the settings. 15
No sound or pictures are outputted
No signal is being inputted. Correctly connect the connection cord. 10, 11
The electrical wiring to this unit is not correctly connected. Correctly connect the connection cord. 10, 11
Pictures are displayed, but no sounds are heard
The volume setting has been set at (or adjusted to) an extremely low level. Adjust the VOLUME setting to a higher level. 17
The MUTE mode is the current setting. Press the MUTE button to release (change) the MUTE mode setting. 17
The electrical wiring to this unit is not correctly connected. Correctly connect the connection cord. 10, 11
Sounds are heard, but no pictures are displayed
The brightness setting has been set at (or adjusted to) an extremely low level.
Adjust the BRIGHT setting to a brighter level. 24
The lens cap has not been removed. Remove the lens cap. 14
Colors have a faded- out appearance Color tone is poor
Perform picture adjustments by changing the COLOR BAL R, the COLOR BAL B, and/or the TINT settings, etc.
Color depth setting or color tone setting
The brightness setting and/or contrast setting has not been properly adjusted.
Perform picture adjustments by changing the BRIGHT and/or CONTRAST settings, etc. 24
The WHISPER mode is the current setting.
Change (by releasing) from the WHISPER mode. 28
Lamp is approaching the end of its product lifetime.
Exchange the old lamp with a new lamp. 30, 31
Either the FOCUS setting or the H PHASE is not properly adjusted. Adjust the FOCUS and H PHASE settings. 15, 25
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.
Page(s) · Pictures appear dark · Pictures appear blurry

Product name Liquid crystal projector
Panel size 1.8 cm (0.7 type)
Drive system TFT active matrix
480,000 pixels (800 horizontal x600 vertical) MP7750
786,432 pixels (1024 horizontal x 768 vertical)
Lens Zoom lens F=1.7 ~ 1.9 f=21.7 ~ 26.1 mm
Lamp 150 W UHB
Speaker 1.0W
Power supply AC100 ~ 120V, 2.7A / AC220 ~ 240V, 1.3A
Temperature range 0 ~ 35°C (Operating)
Size 295 (W) x 87.5 (H) x237 (D) mm
Weight (mass) 2.7 kg
RGB Terminal RGB IN(1, 2) 2 VIDEO Terminal VIDEO IN 1 S-VIDEO IN 1 COMPONENT VIDEO
AUDIO Terminal AUDIO IN(R, L) 1 OUT Terminal RGB OUT 1 CONTROL Terminal CONTROL 1 USB 1
(Y, CB/PB,CR/PR) 1
77.5 217.5

UHB Lamp, 150W (for MP7650) 78-6969-9599-8 UHB Lamp, 150W (for MP7750) 78-6969-9635-0 Air Filter Assy 78-8118-9055-3 Power Cord (US) 78-8118-8102-4 Power Cord (UK) 78-8118-8101-6 Power Cord (Europe) 78-8118-8103-2 VGA Cable 78-8118-8708-8 RCA Video/Audio Cable 78-8118-3234-0
RCA Component Cable w/core 78-8118-9056-1 USB cable 78-8118-9057-9 Remote Control 78-8118-9054-6 Soft Carrying Case 78-6969-9203-7
Ceiling Mount 78-6969-9611-1 Adjustable Height Suspension 78-6969-9564-2 Shipping Case 78-6969-9035-3 S-Video Cable 78-8118-3238-1 Mouse Cable (PS/2) 78-8118-8105-7 Mouse Cable (Serial) 78-8118-8107-3 Mouse Cable (ADB) 78-8118-8106-5 RS-232C Cable 78-8118-3312-4 Mac Adapter 78-8118-3308-2
Please order these parts through your dealer, or contact 3M Customer Service at the following number:
In U.S. or Canada : 1-800-328-1371 In other locations, contact your local 3M sales office.


S-VIDEO
D-sub 15-pin Shrink Mini Din 4-pin
Pin No Signal Pin No Signal
1 Video input Red 9 -
2 Video input Green 10 Ground 3 Video input Blue 11 - 4 -
12 RGB IN [1]: SDA (DDC) 5 Ground RGB IN [2]: - 6 Ground Red RGB OUT : - 7 Ground Green 13 H. sync./ Composite sync. 8 Ground Blue 14 Vertical sync
signal Terminal Specification
Video: Analog 0.7Vp-p, 75Ω terminator (positive) H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level D-sub 15-pin shrink jack
RGB signal input RGB IN
VIDEO IN 1.0Vp-p, 75Ω terminator, RCA jack
0.300Vp-p (PAL/SECAM, burst signal),75Ω terminator Mini DIN 4-pin jack
Y 1.0 Vp-p, 75 Ω Terminator (Positive)
CB/PB 0.7 Vp-p, 75 Ω Terminator (Positive)
CR/PR 0.7 Vp-p, 75 Ω Terminator (Positive)
Audio signal input AUDIO IN
200mVrms, 50 kΩ (max. 3.0Vp-p) RCA jack
TECHNICAL
Video: Analog 0.7Vp-p, 75Ω output impedance (positive) H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level D-sub 15-pin shrink jack
Signal output RGB OUT

Display mode
H × V fH (kHz) fV (Hz) Rating Signal mode
MP7650 MP7750
720 × 400 37.9 85.0 VESA TEXT Zoom in Zoom in
640 × 480 31.5 59.9 VESA VGA (60Hz) Zoom in Zoom in
640 × 480 35.0 66.7 Mac13"mode Zoom in Zoom in
640 × 480 37.9 72.8 VESA VGA (72Hz) Zoom in Zoom in
640 × 480 37.5 75.0 VESA VGA (75Hz) Zoom in Zoom in
640 × 480 43.3 85.0 VESA VGA (85Hz) Zoom in Zoom in
800 × 600 35.2 56.3 VESA SVGA (56Hz) Zoom in
800 × 600 37.9 60.3 VESA SVGA (60Hz) Zoom in
800 × 600 48.1 72.2 VESA SVGA (72Hz) Zoom in
800 × 600 46.9 75.0 VESA SVGA (75Hz) Zoom in
800 × 600 53.7 85.1 VESA SVGA (85Hz) Zoom in
832 × 624 49.7 74.5 Mac16"mode Zoom out Zoom in
1024 × 768 48.4 60.0 VESA XGA (60Hz) Zoom out
1024 × 768 56.5 70.1 VESA XGA (70Hz) Zoom out
1024 × 768 60.0 75.0 VESA XGA (75Hz) Zoom out
1024 × 768 68.7 85.0 VESA XGA (85Hz) Zoom out
1152 × 864 67.5 75.0 VESA SXGA (75Hz) Zoom out Zoom out
1280 × 960 60.0 60.0 VESA SXGA (60Hz) Zoom out Zoom out
1280 × 1024 64.0 60.0 VESA SXGA (60Hz) Zoom out Zoom out
1280 × 1024 80.0 75.0 VESA SXGA (75Hz) Zoom out Zoom out
1280 × 1024 91.2 85.0 VESA SXGA (85Hz) Zoom out Zoom out
1600 × 1200 75.0 60.0 VESA UXGA (60Hz) Zoom out Zoom out


The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu.
Display interval c Back porch b

a b c d TEXT 2.0 3.0 20.3 1.0
a b c d TEXT 3 42 400 1

Projector Computer
GND +5V (POWER ON) DATA
CONTROL Terminal
Mouse jack Mini DIN 4-pin
D-sub 15-pin shrink jack
RTS
+5V
GND
Serial Mouse
Projector Computer
CD RD TD DTR GND DSR
CONTROL Terminal
Mouse jack D-sub 9-pin
D-sub 15-pin shrink jack
SEL0
CTS RTS RTS
10 9 8 7
2 1 4 3
TD
USB Mouse

Projector Computer
CLK DATA
CONTROL Terminal
GND +5V CLK
Mouse jack Mini DIN 6-pin
SEL0
D-sub 15-pin shrink jack
RTS
+5V
GND


(1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and after the computer has started up, turn on the
D-sub 9-pin Projector Computer

Control jack D-sub 15-pin shrink jack
1 Protocol Consist of header (7 bytes) + command data (6 bytes).
2 Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low : Lower byte of CRC flag for command data. CRC_high : Upper byte of CRC flag for command data.
Command data chart


RS-232C jack

Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)
+‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command) (1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +
setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command) (1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+
type (2 bytes) +‘00H’+‘00H’) to the projector. (2) The projector changes the specified setting to the default value. (3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command) (1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+
type (2 bytes) +‘00H’+‘00H’) to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+
type (2 bytes) +‘00H’ + ‘00H’) to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.
When a command sent by the projector cannot be understood by the computer When the command sent by the projector cannot be understood, the error command ‘15H’ is returned by the computer. Some times, the projector ignores RS-232C commands during other works. If the error command ‘15H’ is returned, please send the same command again.
When data sent by the projector cannot be practice When the command sent by the projector cannot be practiced, the the error code ‘1cH’ +‘xxxxH’ is returned. When the data length is greater than indicated by the data length code, the projector will ignore the excess data code. Conversely, when the data length is shorter than indicated by the data length code, an error code will be returned to the projector.

Names Operation type Header
CRC Action Type Setting code
Blue BE EF 03 06 00 CB D3 01 00 00 30 03 00
White BE EF 03 06 00 6B D0 01 00 00 30 05 00
Black BE EF 03 06 00 9B D0 01 00 00 30 06 00
MyScreen BE EF 03 06 00 FB CA 01 00 00 30 20 00
ORIGNAL BE EF 03 06 00 FB E2 01 00 00 30 40 00
Get BE EF 03 06 00 08 D3 02 00 00 30 00 00
Normal BE EF 03 06 00 C7 D2 01 00 01 30 00 00
H Inverse BE EF 03 06 00 57 D3 01 00 01 30 01 00
V lnverse BE EF 03 06 00 A7 D3 01 00 01 30 02 00
H&V Inverse BE EF 03 06 00 37 D2 01 00 01 30 03 00
Get BE EF 03 06 00 F4 D2 02 00 01 30 00 00
Normal BE EF 03 06 00 83 D2 01 00 02 30 00 00
Freeze BE EF 03 06 00 13 D3 01 00 02 30 01 00
Get BE EF 03 06 00 B0 D2 02 00 02 30 00 00
ORIGNAL BE EF 03 06 00 0B D2 01 00 04 30 00 00
OFF BE EF 03 06 00 9B D3 01 00 04 30 01 00
MyScreen BE EF 03 06 00 CB CB 01 00 04 30 20 00
Get BE EF 03 06 00 38 D2 02 00 04 30 00 00
English BE EF 03 06 00 F7 D3 01 00 05 30 00 00
Français BE EF 03 06 00 67 D2 01 00 05 30 01 00
Deutsch BE EF 03 06 00 97 D2 01 00 05 30 02 00
Español BE EF 03 06 00 07 D3 01 00 05 30 03 00
Italiano BE EF 03 06 00 37 D1 01 00 05 30 04 00
Norsk BE EF 03 06 00 A7 D0 01 00 05 30 05 00
Nederlands BE EF 03 06 00 57 D0 01 00 05 30 06 00
Português BE EF 03 06 00 C7 D1 01 00 05 30 07 00
BE EF 03 06 00 37 D4 01 00 05 30 08 00
BE EF 03 06 00 A7 D5 01 00 05 30 09 00
BE EF 03 06 00 57 D5 01 00 05 30 0A 00
Get BE EF 03 06 00 C4 D3 02 00 05 30 00 00
Get BE EF 03 06 00 7C D2 02 00 07 30 00 00
Increment BE EF 03 06 00 1A D2 04 00 07 30 00 00
Decrement BE EF 03 06 00 CB D3 05 00 07 30 00 00
Get BE EF 03 06 00 08 86 02 00 10 31 00 00
Increment BE EF 03 06 00 6E 86 04 00 10 31 00 00
Decrement BE EF 03 06 00 BF 87 05 00 10 31 00 00
Reset Execute BE EF 03 06 00 58 D3 06 00 00 70 00 00
Contrast Reset Execute BE EF 03 06 00 A4 D2 06 00 01 70 00 00
V.Position
Reset Execute BE EF 03 06 00 E0 D2 06 00 02 70 00 00

Names Operation type Header
CRC Action Type Setting code
H.Position Reset Execute BE EF 03 06 00 IC D3 06 00 03 70 00 00
H.Size Reset Execute BE EF 03 06 00 68 D2 06 00 04 70 00 00
R Reset Execute BE EF 03 06 00 94 D3 06 00 05 70 00 00
B Reset Execute BE EF 03 06 00 D0 D3 06 00 06 70 00 00
Sharpness Reset Execute BE EF 03 06 00 C4 D0 06 00 09 70 00 00
Color Reset Execute BE EF 03 06 00 80 D0 06 00 0A 70 00 00
Tint Reset Execute BE EF 03 06 00 7C D1 06 00 0B 70 00 00
Keystone_V Reset Execute BE EF 03 06 00 08 D0 06 00 0C 70 00 00
Keystone_H Reset Execute BE EF 03 06 00 98 D8 06 00 20 70 00 00
Auto Adjust Execute BE EF 03 06 00 91 D0 06 00 0A 20 00 00
Lamp Time Reset Execute BE EF 03 06 00 58 DC 06 00 30 70 00 00
Filter Time Reset Execute BE EF 03 06 00 98 C6 06 00 40 70 00 00
off BE EF 03 06 00 FB D8 01 00 20 30 00 00
on BE EF 03 06 00 6B D9 01 00 20 30 01 00
Get BE EF 03 06 00 C8 D8 02 00 20 30 00 00
BE EF 03 06 00 D9 D8 02 00 20 60 00 00
(Example of Return) 00 00 01 00 02 00 03 00 (Normal) (Cover-error) (Fan-error) (Lamp-error)
04 00 05 00 06 00 07 00 0800 (Temp-error) (Air flow-error) (Lamp-Time-over) (Cool-error) (Filter-Error)
Set OFF BE EF 03 06 00 2A D3 01 00 00 60 00 00 ON BE EF 03 06 00 BA D2 01 00 00 60 01 00
Get BE EF 03 06 00 19 D3 02 00 00 60 00 00
RGB1 BE EF 03 06 00 FE D2 01 00 00 20 00 00
RGB2 BE EF 03 06 00 3E D0 01 00 00 20 04 00
Video BE EF 03 06 00 6E D3 01 00 00 20 01 00
SVideo BE EF 03 06 00 9E D3 01 00 00 20 02 00
Component BE EF 03 06 00 AE D1 01 00 00 20 05 00
Get BE EF 03 06 00 CD D2 02 00 00 20 00 00
Get BE EF 03 06 00 31 D3 02 00 01 20 00 00
Increment BE EF 03 06 00 57 D3 04 00 01 20 00 00
Decrement BE EF 03 06 00 86 D2 05 00 01 20 00 00
Normal BE EF 03 06 00 46 D3 01 00 02 20 00 00
Mute BE EF 03 06 00 D6 D2 01 00 02 20 01 00
Get BE EF 03 06 00 75 D3 02 00 02 20 00 00
Get BE EF 03 06 00 89 D2 02 00 03 20 00 00
Increment BE EF 03 06 00 EF D2 04 00 03 20 00 00
Decrement BE EF 03 06 00 3E D3 05 00 03 20 00 00

Names Operation type Header
CRC Action Type Setting code
Get BE EF 03 06 00 FD D3 02 00 04 20 00 00
Increment BE EF 03 06 00 9B D3 04 00 04 20 00 00
Decrement BE EF 03 06 00 4A D2 05 00 04 20 00 00
Get BE EF 03 06 00 01 D2 02 00 05 20 00 00
Increment BE EF 03 06 00 67 D2 04 00 05 20 00 00
Decrement BE EF 03 06 00 B6 D3 05 00 05 20 00 00
Get BE EF 03 06 00 45 D2 02 00 06 20 00 00
Increment BE EF 03 06 00 23 D2 04 00 06 20 00 00
Decrement BE EF 03 06 00 F2 D3 05 00 06 20 00 00
Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00
Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00
Decrement BE EF 03 06 00 0E D2 05 00 07 20 00 00
Get BE EF 03 06 00 E9 D0 02 00 0B 20 00 00
Increment BE EF 03 06 00 8F D0 04 00 0B 20 00 00
Decrement BE EF 03 06 00 5E D1 05 00 0B 20 00 00
4:3 BE EF 03 06 00 9E D0 01 00 08 20 00 00
16:9 BE EF 03 06 00 0E D1 01 00 08 20 01 00
Small BE EF 03 06 00 FE D1 01 00 08 20 02 00
Get BE EF 03 06 00 AD D0 02 00 08 20 00 00
Default BE EF 03 06 00 62 D1 01 00 09 20 00 00
Bottom BE EF 03 06 00 F2 D0 01 00 09 20 01 00
Top BE EF 03 06 00 02 D0 01 00 09 20 02 00
Get BE EF 03 06 00 51 D1 02 00 09 20 00 00
Get BE EF 03 06 00 0D 83 02 00 00 21 00 00
V.Position
Increment BE EF 03 06 00 6B 83 04 00 00 21 00 00
Decrement BE EF 03 06 00 BA 82 05 00 00 21 00 00
Get BE EF 03 06 00 F1 82 02 00 01 21 00 00
H.Position
Increment BE EF 03 06 00 97 82 04 00 01 21 00 00
Decrement BE EF 03 06 00 46 83 05 00 01 21 00 00
Get BE EF 03 06 00 B5 82 02 00 02 21 00 00
H.Size
Increment BE EF 03 06 00 D3 82 04 00 02 21 00 00
Decrement BE EF 03 06 00 02 83 05 00 02 21 00 00
Get BE EF 03 06 00 49 83 02 00 03 21 00 00 Increment BE EF 03 06 00 2F 83 04 00 03 21 00 00 Decrement BE EF 03 06 00 FE 82 05 00 03 21 00 00
H.Phase
Get BE EF 03 06 00 F1 72 02 00 01 22 00 00
Increment BE EF 03 06 00 97 72 04 00 01 22 00 00
Decrement BE EF 03 06 00 46 73 05 00 01 22 00 00
Get BE EF 03 06 00 B5 72 02 00 02 22 00 00
Increment BE EF 03 06 00 D3 72 04 00 02 22 00 00
Decrement BE EF 03 06 00 02 73 05 00 02 22 00 00

Names Operation type Header
CRC Action Type Setting code
Get BE EF 03 06 00 49 73 02 00 03 22 00 00
Increment BE EF 03 06 00 2F 73 04 00 03 22 00 00
Decrement BE EF 03 06 00 FE 72 05 00 03 22 00 00
Auto BE EF 03 06 00 9E 75 01 00 00 22 0A 00
NTSC BE EF 03 06 00 FE 71 01 00 00 22 04 00
PAL BE EF 03 06 00 6E 70 01 00 00 22 05 00
SECAM BE EF 03 06 00 6E 75 01 00 00 22 09 00
NTSC 4.43 BE EF 03 06 00 5E 72 01 00 00 22 02 00
M-PAL BE EF 03 06 00 FE 74 01 00 00 22 08 00
N-PAL BE EF 03 06 00 0E 71 01 00 00 22 07 00
Get BE EF 03 06 00 0D 73 02 00 00 22 00 00
1080i BE EF 03 06 00 F2 73 01 00 05 22 00 00
1035i BE EF 03 06 00 62 72 01 00 05 22 01 00
Get BE EF 03 06 00 C1 73 02 00 05 22 00 00
off BE EF 03 06 00 CB D0 01 00 08 30 01 00
on BE EF 03 06 00 5B D1 01 00 08 30 00 00
Get BE EF 03 06 00 68 D1 02 00 08 30 00 00
NORMAL BE EF 03 06 00 3B 23 01 00 00 33 00 00
WHISPER BE EF 03 06 00 AB 22 01 00 00 33 01 00
Get BE EF 03 06 00 08 23 02 00 00 33 00 00
NORMAL BE EF 03 06 00 C7 F0 01 00 A1 30 00 00
CINEMA BE EF 03 06 00 57 F1 01 00 A1 30 01 00
DYNAMIC BE EF 03 06 00 A7 F1 01 00 A1 30 02 00
Get BE EF 03 06 00 F4 F0 02 00 A1 30 00 00
Large BE EF 03 06 00 C2 71 01 00 09 22 02 00
Middle BE EF 03 06 00 32 71 01 00 09 22 01 00
Small BE EF 03 06 00 A2 70 01 00 09 22 00 00
Get BE EF 03 06 00 91 70 02 00 09 22 00 00
Full BE EF 03 06 00 43 D6 01 00 12 30 00 00
X1 BE EF 03 06 00 D3 D7 01 00 12 30 01 00
Get BE EF 03 06 00 70 D6 02 00 12 30 03 00
off BE EF 03 06 00 3B EF 01 00 C0 30 00 00
on BE EF 03 06 00 AB EE 01 00 C0 30 01 00
Get BE EF 03 06 00 08 EF 02 00 C0 30 00 00
Lamp Time Get BE EF 03 06 00 C2 FF 02 00 90 10 00 00
Filter Time Get BE EF 03 06 00 C2 F0 02 00 A0 10 00 00

Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
3M Canada P.O. Box 5757 London, Ontario N6A 4T1
3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico
3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France
© 3M 2002 78-6970-9154-0 Rev. A
Litho in Japan
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.