
Operator's Guide
MP8640 Projecteur multimédia Guide de l'opérateur
MP8640 Multimedia-Projektor Benutzerhandbuch
Proyector de Multimedia MP8640 Manual del Usuario
MP8640 Proiettore Multimediale Manuale dell'operatore
MP8640 Bruksanvisning for multimediaprojektor
MP8640 Multimedia Projector Gebruiksaanwijzing



INTENDED USE
Before operating the machine, please read the entire manual thoroughly. The 3M™ Multimedia Projector 8640 was designed, built and tested for use indoors, using 3M™ brand lamps and nominal local voltages. The use of other replacement lamps, outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.
minor or moderate injury. It may also be used to alert against unsafe practices.
The information contained in this manual will help you operate and maintain your 3M MP8640 Multimedia Projector.

THANK YOU FOR CHOOSING 3M
Thank you for choosing 3M Multimedia Projector equipment. This product has been produced in accordance with 3M's highest quality and safety standards to ensure smooth and trouble free use in the years to come.
For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations and training sessions.
3M warrants this product against any defects in material and workmanship, under normal usage and storage, for a period of one year from date of purchase. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, 3M's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).
To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects. In the USA call 1-800-328-1371 for warranty or repair service.
THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS. 3M SHALL NOT BE LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUENTIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT.
FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to comply with the limits for a Class "A" computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference.
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.
Video signal cables: Double shielded coaxial cables (FCC shield cable) must be used and the outer shield must be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.
Video inputs: The input signal amplitude must not exceed the specified level.
IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple© Computer, Inc. Microsoft and Windows 95 are registered trademarks, and Windows and Windows for Work Groups are trademarks of the Microsoft Corporation. All other products are trademarks or registered trademarks of their respective companies. Toshiba is a registered trademark of Toshiba Corporation.

1.1 Contents of Shipping Box
The 3M™ MP8640 Multimedia Projector is shipped with the necessary cables required for standard VCR, PC, MAC™ II or laptop computer connections. Carefully unpack and verify that you have all of the items shown below in Figure 1.1.

VGA Cable (15-15 pin M/M) 3-Conductor Video/Audio Cable
Adapter with dip switch
Video Cable (S-Video mini DIN4-pin)
110V – US 220V – UK, Europe
Figure 1.1 Inventory of Shipping Box
The shipping carton contains the items illustrated in Figure 1.1. In addition, the following items are also included, but not shown here. If any of these items are missing, please contact your place of purchase.
After you have unpacked the MP8640 system and identified all the parts, you are ready to set up the projector.

2.1 Machine Characteristics
The MP8640 Multimedia Projector integrates metal halide lamp and polysilicon LCD display technology into a single unit. It accepts input from two different computer sources and two video/audio sources and projects a bright, super crisp image. Switching your presentation from a computer input to a video input, and then back to a computer input simply requires the push of a button on the remote control keypad or control panel keypad.
The MP8640 Multimedia Projector offers the following features:


STANDBY / ON button Power ON/OFF button. OFF sets the unit in standby mode.
MUTE button.
ZOOM button Adjusts picture size.
Cooling fan (inside) Remote control sensor Lens
FOCUS button Adjusts focus.
RESET button Resets unit to factory settings.
INPUT button To select the input source. Each time this button is pressed, the input source is changed in sequence as shown below. RGB1 RGB2 VIDEO1 VIDEO2
VIDEO input terminal S-VIDEO input terminal VIDEO input terminal AUDIO L/R input terminal
RGB input terminal RGB input terminal AUDIO input terminal
RGB output terminal RGB output terminal AUDIO output terminal
MAIN POWER switch Main power ON/OFF switch.
(RGB/VIDEO) Stereo mini jack
CONTROL terminal D-sub 15pin terminal AC IN socket Connect the provided power cord.

VCR with S-VHS out Laptop Computer
VCR or Laser Disc
The MP8640 must be powered down when making connections. The mouse emulation may not work if the unit is not powered down before the mouse cable connections are made.
2.3.1 Apple™ Desktop Mouse - The Macintosh operating system should recognize the MP8640 as a mouse without any drivers being loaded.
Virtual Mouse for PCs - Setting up for most personal computers (IBM™ compatible). When setting up the virtual mouse function on the projector, the following must be done, if the operating system fails to recognize the projector as a mouse:
Windows™ 3.1 - From "Program Manager" click "Main"; then click "Windows Setup", (make note of what the current mouse driver is); Click "Options"; then "Change Systems Settings". Choose "Mouse". It should be listed as "Microsoft or IBM PS/2".
For some laptop computers you may need to disable the internal pointing device (IPD). This is done through the BIOS level set up of the particular machine, or it could be listed in a "Utilities" program group, i.e., "Toshiba Utilities™," or "Thinkpad Utilities™."
AC In Socket · Desktop Computer


STICK SWITCH If Menu is on screen, stick switch controls movement within menu. If Menu is not displayed, stick switch is used for mouse emulation, i.e. left mouse button and cursor movement.
STANDBY / ON button Power ON/OFF button. OFF sets the unit in standby mode.
RESET / RIGHT button If Menu is on screen, button resets menu to factory default settings. If Menu is not displayed, button is used for mouse emulation, i.e. right mouse button.
ZOOM button Adjusts picture size.
TIMER ON / OFF button Displays or removes TIMER. When the blank screen is displayed, TIMER can not be displayed.
MENU ON / OFF button Displays or removes the on-screen menus.
FOCUS button Adjusts focus.
VOLUME button Adjusts volume.
BLANK ON / OFF button Blanks the screen. Pull down or left on stick switch to reveal screen.
MUTE button Disables sound.
POSITION button Hold this button and move stick switch to adjust vertical and horizontal image position.
INPUT SELECT buttons Selects the input source.
How to insert batteries: Insert the provided batteries (AA or R6P) into the remote control transmitter.

3.1 Installation
Example of the Multimedia projector and screen installation. Determine picture size and projection distance as illustrated below.

24" 48" 71" 119"
endpoints you should verify with your unit that the image is the proper size at the proper distance.


Example on-screen display


1 Hold the STANDBY/ON button for 3-5 seconds.
2 Turn the MAIN POWER switch of the projector off.
3 Close the lens shutter.
4 Disconnect cables.

4.1 Menu
1, 2

RESET
1 Press the MENU ( ) buttons on projector or remote control MENU button.

√ Highlight SETUP option.
S E T U P I N P U T I M A G E O P T .
VOL B R I CON SHA COL T I N
DEFAULT CANCEL
√ To reset a single item from SETUP menu

Adjust the projection position using the foot adjusters at the bottom of the projector.
unlock ← → lock
4.2.1 Lift up the projector, unlock the foot adjusters. 4.2.2 Adjust a viewing angle, and then lock the foot adjusters. 4.2.3 For fine adjustments, rotate the foot adjusters.
If the foot adjusters do not lock completely, turn the foot adjusters slightly before locking.
Foot adjusters

The menu SETUP is used to adjust the image and to move the image position.
RGB signal input Video signal input


BRIGHT (BRIGHTNESS)
CONTRAST
SHARPNESS
COLOR
TINT
V.POSIT (V.POSITION)
Moves the picture up or down.
Moves the picture left or right.
Decreases the picture flicker
Widens or Narrows the horizontal size of picture
R=stronger Red; N=Normal; B=stronger Blue

The menu INPUT is used to select the input source.
S E T U P I N P U T I M A G E O P T .

RGB1
Selects the RGB 1 terminal.
Selects the RGB 2 terminal.
Selects the VIDEO 1 terminal.
SYSTEM Selects the video signal format.
Selects the VIDEO 2 terminal.
Selects the TEST PATTERN. (Start up screen).
The IMAGE menu is used to alter the image.
S E T U P I N P U T I M A G E O P T .
S E T U P I N P U T I M A G E O P T .
M I R R O R
S E T U P I N P U T I M A G E O P T .
S E T U P I N P U T I M A G E O P T .
WHITE BLUE BLACK
R E V E A L
FAST
MEDIUM
SLOW
Selection · Description


S E T U P I N P U T I M A G E O P T .
Inverts the picture horizontally or vertically.
H : INVERT Inverts the picture horizontally. V : INTERT Inverts the picture vertically. H&V: INVERT Inverts the picture horizontally and vertically.
BLANK
Selects the blank color.
Selects reveal speed. Note: For XGA inputs, "REVEAL" does not work.
See chart below.
Turn off the on-screen message.
640 X 480 Normal Displays in 640x480 window centered on screen. Large Expands 640x480 to full 800x600 screen.
800 X 600 Normal Displays full 800x600. Large Not available.
1024 X 768 Normal Compresses 1024x786 to 800x600 screen. Large Displays 800x600 "window" into 1024x768. This window can be moved with H and V Position or by holding position button and moving the stick switch.
Video Normal Displays video in a 640x480 window centered on screen. Large Expands video to fill 800x600 screen
Selection · Description

The OPT. menu allows you to control communication function.
S E T U P I N P U T I M A G E O P T .
COM. SPEED COM. BITS TIMER LANGUAGE AUTO OFF STARTUP
S E T U P I N P U T I M A G E O P T .
S E T U P I N P U T I M A G E O P T .
1200 2400 4800 9600 19200
S E T U P I N P U T I M A G E O P T .
S E T U P I N P U T I M A G E O P T .
ENGLISH FRANCAIS DEUTSCH ESPANOL ITALIANO NORSK NEDERLANDS
10 min. TIMER
S E T U P I N P U T I M A G E O P T .
0 min. STOP AUTO OFF
COM. SPEED
Selects the data speed of transmission. (For mouse emulation-1200)
Selects the data format of transmission. 7N1... 7 data-bits, No parity, 1 stop bit. (For mouse emulation-7N1) 8N1... 8 data-bits, No parity, 1 stop bit.
TIMER
Sets the timer (in minutes).
Selects the language on-screen menu. (English, French, German, Spanish, Italian, Norwegian, Dutch)
AUTO OFF
Selects how long projector will stay on, if no input is detected. Select 0 to disable this function.
Enable/Disable Startup Screen.
(bps) · Selection · Description

5.1 Connection to the Video Signal Terminal
Luminance signal 1.0Vp-p, 75 Ω termination Chrominance signal 0.286Vp-p (burst signal), 75 Ω termination
1.0Vp-p, 75Ω termination
200mVrms, 20 kΩ below (MAX 3.0Vp-p)
S VIDEO input (Mini DIN4 pin)
1. S-VIDEO input terminal 2. RCA jack (composite) input terminal
5.2 Connection to the RGB Signal Terminal
a. Input signal / Output signal
Analog 0.7Vp-p 75 Ω termination (Positive polarity)
TTL level (Positive/negative polarity)
TTL level (Positive/negative polarity)
200mVrms, 20k Ω below (MAX 3.0Vp-p)
0 ∼ 200mVrms, 1k Ω
N.C
N.C
N.C
N.C
N.C D-sub 15pin (Male)

VGA-1 (IBM™ compatible)
VGA-2 (IBM™ compatible)
VGA-3 (IBM™ compatible)
Macintosh™ 13 inch mode
VESA 72 Hz standards
Macintosh™ 16 inch mode
Projector is compatible with 13 inch mode and 16 inch mode. Set all dip switches OFF except those indicated in the chart. For example:
MAC 13" mode = switch 1, 5 and 6 are ON MAC 16" mode = switch 2, 5 and 6 are ON
(Example of 16 inch mode)

(1) While the projector and computer are turned OFF, connect the projector and the mouse terminal of
computer using an appropriate cable. (PS/2, Serial or ADB)
(2) Turn ON the projector.
(3) Turn ON the computer.
(4) Select the correct mouse driver for the application. See computer's User Manual for this procedure.
ADB mouse
ADB port D-sub 15pin (Female)
PS/2 port · D-sub 15pin (Female)


This cable is used to directly control the projector without using the Remote Control or Operator's Panel.

6.1 Cleaning the Air Filter
a) Turn off the MAIN POWER switch of the projector and pull out power cord. Let cool for 20 minutes.
b) Remove the air filter from the bottom of projector. Unscrew two retaining screws and pull down and
out on the handle to free air cleaner door. Carefully lift up and out on filter door.

Remove the air filter
c) Clean the air filter using a vacuum cleaner. If dirt is still present, wipe the air filter with a cloth moistened with water and wipe with a dry lint-free cloth.
d) After filter dries completely, re-install the air filter.
NO SIGNAL IS DETECTED: The projector is not detecting a signal. SYNC IS OUT OF RANGE: The horizontal frequency of the input signal exceeds the range of the projector, or it cannot be displayed. CHANGE THE LAMP: Change when the lamp message appears on the screen. See Section 6.3 for more information.
b) Indicator Display. The ON indicator, LAMP indicator and TEMP indicator will light or blink in the
following cases:
Cool projector by power off for 20 minutes.
Ensure filter is closed.
Temperature inside too high
Let projector cool 20 minutes. Check air flow and filter.
Cooling fan not operating
*When the LAMP indicator lights or blinks, turn the power off. If the problem persists, contact your dealer.

If there is a need to determine the lamp operation hours, follow these steps:
a) While the projector is running, press and hold the timer button on the remote control for 3 seconds.
b) The operating time of the lamp will be displayed. If the operating hours are greater than 1,900 the
"CHANGE THE LAMP" message will appear. If the hours are greater than 1,980 the following message will appear, "POWER WILL SHUT OFF IN 20 HOURS" The number of hours left until shut down will decrease until 0 hour is reached, then power will be turned off.
c) To reset the timer, press the reset button and select 0 (or CANCEL). The "CHANGE THE LAMP" message will not come up if the timer is reset.
Warning: Always turn off and unplug projector when
changing lamp. Warning: Lamp and adjacent metal parts become

extremely hot and can cause severe burns to your fingers. Allow the projector to cool for at least 30 minutes before replacing the lamp.
6.3.1 Remove lamp access door: The lamp access door is located on the bottom of the machine on the right side. Use a flathead screwdriver to unscrew the cover retaining screws and gently open the cover and set it aside..
6.3.2 Retaining screws: Use a standard screwdriver to unscrew the lamp module retaining screws.


6.3.3 Remove lamp module: Grasp the lamp module with the one hand and the projector body opening with the other hand. Apply pressure to the projector body as you slide the lamp out.

6.3.4 Insert lamp module: Carefully insert the new lamp module. Ensure that it is fully seated.

Tighten the lamp module retaining screws to secure the lamp module in place.
Insert the hinge tabs on the left side of the lamp access door, then close and tighten the retaining screws to secure the door.
Check the following table before asking for service. If a solution cannot be found, consult dealer.
Power cannot be turned on.
No picture and sound
Sound is heard with no picture
Picture is displayed with no sound
Color is weak and tint is incorrect
Picture is not clear
LAMP indicator lights red.
TEMP indicator lights red.
LAMP indicator blinks red.

7.1 Specifications
3 beam poly-silicon LCD
1.3 inches (33 mm)
480,000 pixels (V600 × H800) per panel. 1.44 million pixels total with 3 panels.
Metal halide lamp 260W
2W and 2W (stereo)
AC100 ∼ 120V, 5A / AC220 ∼ 240V, 2.2A (Universal)
32° ∼ 95°F (0° ~ 35°C)
16.3" (W) × 5.9" (H) × 12.0" (D) 414 mm (W) x 150 mm (H) x 305 mm (D)
18 lbs. (8.1 kg)
video signal input terminal
RGB input/output signal terminal
78-6969-8425-7 26-1011-8852-7 78-8118-3304-1 78-8118-3303-3 26-1011-3421-6 78-1011-3308-2 26-1011-3419-0 78-8118-3306-6 78-8118-3315-7 78-8118-3313-2 78-8118-3314-0 78-8118-3312-4 (not included with basic packout)


Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada from 7:30 a.m. to 5:30 p.m. (CST) or visit our Internet Website.

Printed on 50% recycled wastepaper,
3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
3M Canada P.O. Box 5757 London, Ontario N6A 4T1
3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico
3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France
Litho in USA © 3M 1997 78-6970-7912-3
including 10% post-consumer
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Power cannot be turned on. | •The Main power is not turned on. •The power cord is disconnected. | •Turn the MAIN POWER switch on. •Insert the power cord into an AC socket. | p.25 |
| No picture and sound | •The setting of the input source is not correct. •RGB/Video/Audio wiring to projector is not correct. | •Set the correct input using the input select button of the projector or the remote control. •Connect the cable correctly. | p.25 |
| Sound is heard with no picture | •RGB/Video wiring to projector is not correct. •The brightness is set fully to dark. | • Connect the cable correctly. •Press the MENU button and increase BRIGHTNESS. | p.25 |
| Picture is displayed with no sound | •Audio wiring to projector is not correct. •The volume is set to minimum. •The unit is muted. | • Connect the cable correctly. • Press the VOL button and increase VOLUME. • Press the MUTE button. | p.25 |
| Color is weak and tint is incorrect | • The color and tint have been adjusted incorrectly. | • Adjust the color and tint correctly. | p.25 |
| Picture is dark | •The brightness and contrast has been adjusted incorrectly. •The lamp needs to be replaced. | •Adjust the brightness and contrast correctly. •Replace the lamp with a new one. | p.25 |
| Picture is not clear | • Projector is out of focus. | • Adjust the focus. | p.25 |
| LAMP indicator lights red. | • Lamp will not ignite. | • Turn off power and let cool for 20 minutes, then restart. • If problem persists call your dealer. | p.25 |
| TEMP indicator lights red. | • Temperature inside projector is too hot. | • Do not block the ventilation holes. • Clean air filter | p.25 |
| LAMP indicator blinks red. | • Air filter door on bottom of case is open. | • Ensure air filter door is closed. | p.25 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.