

Operator’s Guide
MP7630B/MP7730B Projecteur personnel Guide de l’opérateur
MP7630B/MP7730B Personal Projektor - Benutzerhandbuch
MP7630B/MP7730B Guía del Usuario del Proyector Personal
MP7630B/MP7730B Guida dell’operatore per il Proiettore personale
MP7630B/MP7730B Bruksanvisning för Personlig projektor
MP7630B/MP7730B Personal Projector - Gebruiksaanwijzing






Before operating the machine, please read the entire manual thoroughly. The 3M Personal Projector MP7630B/ MP7730B was designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, operation in environments containing heavy cigarette smoke or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It may also be used to alert against unsafe practices.
Note - Used to emphasize important conditions or details.

The following safety labels are used on or within the MP7630B/MP7730B projector to alert you to items or areas requiring your attention.
HIGH VOLTAGE / HIGH TEMPERATURE / HIGH PRESSURE WHEN REPLACING THE LAMP, TURN OFF THE PROJECTOR AND PULL OUT THE CORD FROM THE RECEPTACLE BEFORE REPLACING THE LAMP. WAIT UNTIL THE LAMP BECOMES COOL (MINIMUM 45 MINUTES). TOUCHING THE LAMP WHEN IT IS HOT MAY CAUSE A BURN ON YOUR HAND. HIGH PRESSURE LAMP WHEN HOT MAY EXPLODE IF IMPROPERLY HANDLED. REFER TO USER'S GUIDE.
HAUTE TENSION / HAUTE TEMPERATURE / HAUTE PRESSION ETEIGNEZ LE PROJECTEUR ET DÉBRANCHEZ LE CORDON D'ALIMENTATION DE LA PRISE AVANT DE REMPLACER L'AMPOULE. LAISSEZ REFROIDIR L'AMPOULE (U MOIN 45 MINUTES) AVANT DE LA RETIRER. POUR NE PAS VOUS BRULER LES MAINS. EN CAS DE MAUVAISES MANIPULATION LES AMPOULES HAUTE PRESSION RISQUENT D'EXPLOSER QUAND ELLE SONT CHAUDES. CONSULTEZ LE MODE D'EMPLOI.
HOHSPANNUNG / HOCH TEMPERATUR / HOCHDRUCK BEIM AUSWECHSELN DER GLÜHLAMPE DEN PROJEKTOR AUSSCHALTEN UND NETZKABEL AUS DER WANDSTECKDOSE ABZIEHEN, VOR DEM AUSWECHSELN DER GLÜHLAMPE WARTEN, BIS SICH DIE LAMPE ABGEKÜHLT HAT (MINDERSTENS 45 MINUTEN) DARAUF ACHTEN. DAB DIE HEIBE GLÜHLAMPE NICHT BERÜHRT WIRD DA DIES VERBRENNUNGEN VERURSACHEN KANN. BEI UNSACHGEMÄSSER BEHANDLUNG KANN DIE UNTER HOEHM DRUCK STEHENDE BIRNE EXPLODIEREN SICH AUF DIE BEDIENUNGSANLEITUNG BEZIEHEN.
EXIT
FREEZE BLANK
ALTO VOLTAGGIO / ALTA TEMPERATURA / ALTA PRESSION SE SI DEVE SOSTITUIRE LA LAMPADA, SPEGNERE IL PROIETTORE ED ESTRARRE LA SPINA DEL CAVO DI ALIMENTAZIONE DALLA PRESA DELLA RETE ELETTRICA PRIMA DI SOSTITUIRE LA LAMPADA. ASPETTARE CHE SI RAFFREDDI (ALMENO 45 MINUTI) A TOCCARE LA LAMPADA QUANDO È CALDA SI CORRE IL RISCHIO DI SCOTTARSI LA MANO. CONSULTARE LE ISTRUZIONI PER L'USO.
R-CLICK
DRAG
+ MAGNIFY -
+ VOLUME -
RETURN
MUTE
CH UP CH DOWN REVERSE
ALTO VOLTAJE / ALTA TEMPERATURA / ALTA PRESION PARA REEMPLAZAR LA LÁMPARA, APAGUE EL PROYECTOR Y RETIRE EL CABLE DE ALIMENTACION DEL TOMACORRIENTE ANTES DE REEMPLAZAR LA LÁMPARA. ESPERE HASTA QUE LA LÁMPARA SE ENFRIE (ALMENOS 45 MINUTOS) SI TOCA LA LÁMPARA CUANDO ESTÁ CALIENTE, PUEDE QUEMARLE LAS MANOS. LA LÁMPARA ES ALTA PRESION CUANDO ESTÁ CALIENTE. PUEDE EXPLOTAR SI NO ES MANIPULADA DEBIDAMENTE. CONSULTE LA GUÍA DEL USUARIO.
WARNING / AVERTISSEMENT / VORSICHT / PRECAUCION
RISK OF ELECTRIC SHOCK - DO NOT OPEN. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
POUR PRÉVENTIR DE TOUT CHOC ÉLECTRIQUE, NE PAS OUVRIR L'APPAREIL. AUCUNE PIÈCE INTERNE N'EST CHANGEABLE PAR L'UTILISATEUR. POUR LA MAINTENANCE, SE REFÉRÉR AU PERSONNEL QUALIFIÉ.
PARA PREVENTIR DESCARGAS ELECTRICAS, NO ABRIR LA TAPA, NI MANIPULAR EN SU INTERIOR SI NO ES POR PERSONAL CUALIFICADO.
Apparatet mä kun tilkoples jordef stikkontakt.
Laite on liitettävä suojakesketimpistorasiaan, jos se on liitetty lanjaan johdinverkoon.
APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG NÄR DEN ANSLUTS TILL ETT NÄTVERK.
Made in / Fabrique au / Hecho en - Taiwan

In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a bandwidth of 110 to 230 volts ± 10 volts, but could fail if power drops or surges of ±10 volts occur. In these high-risk areas, it is recommended to install a power stabilizer unit. Caution
The information contained in this manual will help you operate and maintain your 3M™ MP7630B/MP7730B Personal Projector.
+/-

Thank you for choosing 3M multimedia projection equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come.
For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations, and training sessions.
Limited Warranty 3M warrants this product against any defects in material and workmanship, under normal usage and storage, for a period of two years from date of purchase. Exclusion to Warranty: The lamps are considered a consumable item and are warrantied for 90 days or 180 hours, whichever occurs first. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, 3M’s only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects. In the USA call 1-800-328-1371 for warranty or repair service. Limitation Of Liability THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3M SHALL NOT BE LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUEN- TIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT. Important: The above warranty shall be void if the customer fails to operate product in accordance with 3M’s written instructions. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. FCC STATEMENT - CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can by determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. Instructions to Users: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that following conditions are met. The cables (power cord, RGB cable and other cables) may have to be used with the core set to the projector side. Use the cables which are included with the projector or specified.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTICE: This Class B digital apparatus complies with Canadian ICES-003. Pour les utilisateurs au Canada AVIS: Cet appareil numérique de la Clase B est conforme à la norme NMB-003 du Canada.
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements. Video Signal Cables: Double shielded coaxial cables (FCC shield cable) must be used, and the outer shield must be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation. Video Inputs: The input signal amplitude must not exceed the specified level. Patents, Trademarks & Copyrights IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple Computer, Inc. Microsoft and Windows 95 and Windows 98 are registered trademarks, and Windows and Windows for Workgroups are trademarks of the Microsoft Corporation. Toshiba is a registered trademark of Toshiba Corporation. All other products are trademarks or registered trademarks of their respective companies.
Core

The 3M™ MP7630B/MP7730B Personal Projector is shipped with the necessary cables required for standard VCR, PC, Macintosh™ or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Power Cords VGA US, UK, Europe Cable MP7630B/MP7730B
PS/2 Mouse Adapter Cable
Serial Mouse Adapter Cable
ADB Mouse Adapter Cable
MP7630B/MP7730B
MP7630
DLP A TEXAS INSTRUMENTS PRODUCT
© 3M IPC May 2000 Rev. B
A TEXAS INSTRUME NTS PRO DUCT
78-6970-9035-1 Acrobat® Reader copyright © 1987-1996 Adobe Systems Incorporated. All rights reserved. Adobe and Acrobat are trademarks of Adobe Systems Incorporated which may be registered in certain jurisdictions.
Ch Up Ch Down Reverse
A TEXAS INSTRUMENTS PRODUCT
3M Austin Center A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
MP7630 Product Safety Guide
Acrobat® Reader copyright
© 1987-1996 Adobe Systems
Incorporated. All rights
reserved. Adobe and Acrobat
are trademarks of Adobe
Systems Incorporated which may
be registered in certain jurisdictions.
DLP A TEXAS INSTRUMENTS PRODUCT
Visual Systems Division 3M Austin Center A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
MP7630/7730 Operator’s Guide
© 3M IPC May 2000 Rev. B 78-6970-9035-1
MP7630B/MP7730B Personal Projector Quick Start Guide
Ch Up Ch DownReverse
Visual Systems Division
3M Austin Center
6801 River Place Blvd.
Austin, TX 78726-9000
© 3M IPC May 2000
Rev. B
78-6970-9035-1 Acrobat® Reader copyright
© 1987-1996 Adobe Systems
Incorporated. All rights
reserved. Adobe and Acrobat
are trademarks of Adobe
Systems Incorporated which may
be registered in certain jurisdictions.
MP7630
DLP A TEXAS IN
DLP A TEXAS INSTRUME NTS PRO DUCT
MP7630B/MP7730B Personal Projector Quick Start Guide
Sourc Stand Las Menu Freeze Blan
Ch Up Ch Do Reve Add/Er Scan 12 456 7809
D
DLP A TEX INST NTS DUC
DLP A TEXAS INSTRUMENTS PRODUCT
MP7630 Product Safety Guide
Visual 3M A ustin C A145- 6801 R Austin
© 3M Rev 78-69 Acrobat® R © 1987-19 Incorporat reserved. A are tradem Systems In be register
MP7630 Product Safety Guide
D
3 MP7630 Multimedia Projector QuickStart
A TEXAS INSTRUMENTS PRODUCT
(CD-ROM)
Optional Accessories
Video Module (RCA with tuner) (1)
Video Module (SCART without tuner) (1)
Note: For more information on the Optional Video Module and its functions, please see the Optional Video Module section of this manual.
Note: Save the shipping box and packing materials in the event the MP7630B/MP7730B should require shipping to a 3M Service Center for repair.
After you have unpacked the MP7630B/MP7730B and identified all the parts, you are ready to set up the projector.
Please read this guide thoroughly before operating your new projector.
Be sure to check our web site (www.3m.com/meetings) regularly for updates and supplemental information. On the CD-ROM, you can link directly to the web site by clicking here or on “3M Innovation” in the lower right corner of the Main Menu.



The MP7630B/MP7730B Personal Projector integrates ultra-high bright lamp and TI™ DLP™ technology into a single unit.
The MP7630B/MP7730B Personal Projector offers the following features:
The MP7630B/MP7730B Personal Projector offers the following optional features:
Note: The brightness of your machine will vary depending on the ambient room conditions and contrast/
brightness settings.
The External Control Pad is located on top of the projector, near the back end.
The Infrared Remote Receivers allow the projector to accept signals from the remote control. For best results, be sure to aim the control toward the sensors, without any obstructions between the two, and at a distance no greater than 4 meters (13 feet).
The Menu button will display the menu system onscreen. Press Menu again to access the sub-menus.
The Keystone buttons help correct keystone distortion of a projected image. The Keystone + button corrects distortion in the upper part of the image. The - Keystone corrects it in the lower part. When you are viewing the onscreen menus, the Keystone buttons help navigate among choices and settings in the sub-menus.
Press the Auto button to automatically adjust a projected image on screen. When you are viewing the onscreen menus, press Auto to go back to the Main Menu. Press Auto again to exit the menu system.
The Lamp Status Indicator will blink or light up when the lamp needs service, cooling or replacement. See page 34 for more detailed information.
When the projector is turned on, the Standby/On Indicator will blink during warm-up and lamp ignition, then stay green to indicate the projector is ready for use.
Press the Standby/On Button to turn the projector on or off.

Source Press button to change input source.
Standby/On Press STANDBY/ON button to begin projection mode (lamp on). To turn lamp off, press STANDBY/ON, then select YES on Shutdown screen. Select NO to continue running.
Laser Press button to turn on the Laser Pointer
Exit Press button to exit menu screens.
Menu Selection Arrows Press buttons to change between the four menus.
Menu Press to display the menu screen.
Freeze Press button to turn the freeze image function ON/OFF.
Blank Press button to turn the screen blanking function ON/OFF.
L-Click Press for left mouse button function, Mouse Mode. Press for select function, Menu Mode.
Disk Pad Operate for normal mouse functions, Mouse Mode, to select function, Menu Mode.
R-CLICK
DRAG
R-Click Press for right mouse button function, Mouse Mode.
Drag In mouse mode, press button to hold, reposition and drop an object on the screen. To MAGNIFY an area, press MAGNIFY button then press the DRAG button and change the magnifying position by moving the Disk Pad.
+ VOLUME -
RETURN
MUTE
Volume Press (+) to increase or (-) to decrease speaker volume.
Magnify Press (+) to increase or (-) to decrease the size of the displayed image.
Mute Press button to turn the mute function (speaker sound) ON/OFF.
Return Press button to return to last menu or command.
Reverse* Press to go back to previous channel.
Scan* Scans channels which have good reception.
Channel Up and Down*
Press button to increase the channel number.
Add/Erase* Add favorite channels/Erase channels which were previously added.
Press button to decrease the channel number.
* Note: These features are for use only with the optional video module.
+/-

The remote control sensor is located near the back of the projector. The distance between the sensor and the remote control unit must be shorter than 4 meters (13 feet).
Freeze The image will be frozen when the Freeze button is pressed. A “Pause” icon appears at the lower right of the screen for three seconds during the freeze function. A “Play” icon appears at the lower right of the screen for three seconds when the freeze function is released. To release the freeze function, press the Freeze button or Source button (when the input source is switched over during display).
“Pause” icon “Play” icon
Mute Pressing the Mute button will mute the sound. A text box saying “Mute” appears at the lower right of the screen. Press Mute button again or Volume + or - button to release the function.
Volume Press the Volume + or - button to adjust the loudness. The volume slide bar will disappear three seconds after the last adjustment is made.
Magnify By pressing Magnify +, the center of the picture can be magnified, doubling in size. When the button is pressed again, the picture is further magnified, up to four times the original size. By pressing Magnify -, the size of the image is reduced to half its size. When the button is pressed again, the picture is further reduced until it is restored to the original size. To return to the normal display mode, press the Return button. (This function can be used in combination with the Freeze function.)
Magnify button Magnify icon

Laser Press this button to generate the laser beam that functions as a red pointer on the screen.
Disk Pad If the PS/2 (ADB) mouse cable is connected with the PC Notebook or Mac PowerBook mouse port, the Disk Pad can take over the Notebook or PowerBook mouse function. When the Magnify func- tion is activated, use the Disk Pad to move around the display areas. Note: The mouse function is not available when the Magnify function is turned on.
R-Click, L-Click These two keys are used when the mouse function is activated after the PS/2 port is connected. They act as the right (R) and left (L) buttons of a computer mouse.
L-Click button R-Click button
Drag This button toggles between ON and OFF for the drag function of the remote mouse.
Blank Press this button to activate or release the Blank function. Blank makes the screen go blank.

Place the projector at the required distance from the screen according to the desired picture size (see the table below).

For your own customized screen chart, please click here (on the CD-ROM) or visit our Projector to Screen Calculator on the 3M web site (www.3m.com/meetings/screen/7630_calc.html).
Keystoning is when the projected image is noticeably wider on either the top or bottom. There are two ways to correct this:


It only takes a few minutes to connect the 3M™ Personal Projector MP7630B/MP7730B to your computer, VCR, or other device.



The general cable links the projector to the proper mouse adapter cable for your computer.
Male Mini-DIN Female Mini-DIN
Apple™ Desktop Mouse The Macintosh operating system should recognize the MP7630B/MP7730B as a mouse without any drivers being loaded.
VirtualMouse for PC Computer For IBM™ compatible computers, set the operating systems to Serial Mouse or PS/2 Mouse to recognize projec- tor as the mouse pointer device.
To set mouse driver information:
b) Windows™ 3.1 From Program Manager
Note: For proper mouse operation, always turn the projector power on first and power up the computer. For some laptop computers, you may need to disable the internal pointing device (IPD). This is done through the BIOS level set-up of the particular machine, or it could be listed in a “Utilities” program group, i.e., “Toshiba Utilities ™ ,” or “Thinkpad Features ™ .”
General cable


Note: Make all cable connections and line hookups with the power off.
The 2-prong adapter with ground is used with older U.S. electrical outlets that only support 2-prong power cord plugs.
ground lead MUST be securely fastened to the ground screw on the outlet.
Plug the 2-prong adapter into the bottom socket of the eletrical outlet. Hook the end of the ground lead firmly around the neck of the outlet’s ground screw. Tighten the screw, if necessary, to hold the ground in place. Then plug the power cord into the adapter.
Note: If you have the Optional Video Module attached to the unit, press the Source button on the remote to select the source of the signal to be projected onto the screen. The selected signal input is displayed at the top right of the screen. The display will show the last selected input source before power was turned off. (For more information, please refer to the Optional Video Module section of this manual.)


00:01:00 00:00:00 00:00:30
00:01:30
Power

Do not unplug power cord before pressing the Standby/On button. After the Standby/On button is pressed, the fan rotates for about 90 seconds to cool the projector. Caution

Press Menu on the remote control or external control pad, and the main menu will display on the screen. Press Menu again to enter page items, and press Keystone buttons to select sub-menus. The main menu will go off automatically if there is no further action from user for 10 seconds. Press the Auto button to leave the current sub-menu, and press Auto again to leave the main menu.
U N E M
}
R A B
T U O Y A L s u n e M y a l p s i D s u n e M e g a m I s u n e M l o rt n o C u n e M e c r u o S
(only with Video Module)
e zi S o t u A
e g a u g n a L
e n o ts y e K
t u o h ti W
e s a h P la t n o zir o H
r o rri M
l a n o it p O
s s e n t h gir B
c n y S la t n o zir o H
k n al B
) elb a cilp p a t o n (
o e d i V
ts a rt n o C
e l u d o M
n oitis o P la t n o zir o H
ff O o t u A
e c n ala B r olo C
n oitis o P la citr e V
t e s e R
e zi S o t u A
e g a u g n a L
e c r u o S
e n o ts y e K
c a M r o C P
e s a h P la t n o zir o H
r o rri M
e m ulo V
s s e n t h gir B
l a n o it p O
c n y S la t n o zir o H
k n al B
elb e r T
ts a rt n o C
o e d i V
n oitis o P la t n o zir o H
ff O o t u A
s s a B
e l u d o M
s s e n p r a h S
n oitis o P la citr e V
t e s e R
e t u M
e g a u g n a L
e c r u o S
o e d i V
e n o ts y e K
t u p n I
r o rri M
e m ulo V
s s e n t h gir B
s s e n p r a h S
k n al B
elb e r T
l a n o it p O
ts a rt n o C
oit a R e g a m I
o e d i V
ff O o t u A
s s a B
e c n ala B r olo C
m e ts y S
e l u d o M
t e s e R
e t u M
h ti w · t ni T · h ti w











Auto Will automatically adjust projected image.
Language English (En) French (Fr) Deutsch (De) Italian (It) Español (Es) Portuguese (Po) Simplified Chinese ( )
Will invert image to display properly according to position of projector.
Vertically Inverted) (Rear-screen projection, ceiling mounted)

Will turn off the power in 60 minutes.
00:00:00 00:60:00
Will reset the lamp hours after lamp is changed.

The Optional Video Module makes it possible to hook the MP7630B/MP7730B to a laser disc, VCR, or other video devices. Two versions will be available: an NTSC Package (with RCA connectors and television tuner), and a PAL package (with a SCART connector and no television tuner).

Back of projector without Optional Video Module

Back of projector with PAL SCART Module Top view of video module



Power down the projector before connecting the Optional Video Module or any other device. Failure to do so may cause serious damage.

Pressing the Source button on the remote control or the projector will cycle between these choices of input signals: RGB (computer), Video (composite video from a VCR), S-Video, and Tuner. The projector will then search for the selected type of signal until it is found or switched to another type.

The MP7630B/MP7730B can receive over 100 television channels. In Tuner mode (TV and CATV), press the Scan button on the remote control to view all available television channels. The message “DO YOU REALLY WANT TO SCAN? YES NO” will appear onscreen. Press either the left or right arrow buttons on the remote to reach Yes or No, then press the Menu button to enter the selected answer. The message “TUNER IS SCANNING NOW” will display for a few seconds, and then the scanned channels will appear for a few seconds each.
Scan button Left and Right buttons

This menu is only available when the input signal is from Video, S-Video, TV or CATV.

Less More
Tint
Red Green (Source is video or S-video)
4:3 (Normal) 16:9 (Video)
System
Auto PAL-M PAL-N SECAM




in the local CATV system.
Yes No
After the “START SCANNING?” dialog box prompt, use the Channel Up/Down buttons to select “Yes” or “No.” Press Return button to set.
Function (Must be performed with remote control unit)
Channel Select Press the channel number button user wants to select (for example, 12), then press Return button to set.
Channel Up/Down Go up and down through channels by pressing the Channel Up/Down buttons. The channel number will appear in the lower right corner of the screen. If there is no further action for three seconds, the channel number display will disappear automatically.
Scan Press the Scan button for two seconds to begin scanning TV channels.
Add/Erase Press the Add/Erase button for two seconds to add or erase the channel. To delete channels from memory, press the button to erase the channel. A “Channel Erased” message will display. Users can also add channels to memory by pressing the button after selecting it. A “Channel Added” message will display.
Reverse Press the Reverse button to toggle between the previous and current channels.


RED WHT YEL
RED WHT
VCR
Laser Disc Cable Box

Use and Replacement of Lamp
The projector lamp has a normal operating time of approximately 1200 to 1500 hours, called the lamp life. During the normal lamp life, the picture will be bright and the colors clear. If the lamp is used beyond the normal lamp life, the picture will become dark and the colors poor. Always replace lamps with new ones. Using an old lamp in the projector could cause a malfunction. When the power is turned on, the LAMP indicator will light up red or a message will be displayed to indicate when it is time to replace the lamp. Consult your dealer.
Lamp Exceed Service Hours — When this LED lights red continuously, it is warning you that the lamp has exceeded 1500 service hours. Replace the projection lamp immediately.
PLEASE CHANGE A NEW LAMP AND RESET THE TIMER— The lamp has been operated for 1400 hours.
PLEASE CHANGE A NEW LAMP, THE POWER WILL TURN OFF AFTER 20 HOURS — The lamp has been operated for 1480 hours, and the power will turn off after 20 more hours.
PLEASE CHANGE A NEW LAMP — The lamp has been operated for more than 1500 hours, and the power will turn off automatically after 10 minutes.
All of these messages will not display for more than 3 minutes, but each message will be dis- played whenever you turn on the lamp again.
Lamp is not well attached — When the LED blinks rapidly, it indicates that the lamp is not attached properly.
Temperature is too high — When the projector’s internal temperature is too hot to operate safely, the LED blinks slowly for one minute and the lamp goes off automatically.
If the LED light is off, it means that the projector’s lamp and temperature are operating under normal conditions.
The LAMP indicator will light if the lamp becomes too hot. Turn off the power and let the projector cool for 45 minutes. Turn on. If the LAMP indicator still lights up red, please contact your dealer.

power cord before changing lamp.
1. Turn the main power switch off and disconnect the power cord from the outlet. 2. Loosen screw and remove the lamp cover. If the lamp is hot, avoid burns by waiting 45 minutes until lamp has cooled. 3. Loosen two screws designated by arrows below. (It is strongly recommended to use a magnetic- headed screwdriver, if possible. Pull the handle to remove lamp housing. If the screws are not loosened completely, they could damage your fingers. Do not insert your hand into the box after the lamp is removed. If the optical parts inside are touched by hand, it could cause color unevenness, etc. 4. Replace the lamp with the new one, insert into projector, and tighten the screws. Firmly tighten the lamp screws. Loose screws may cause a bad connection, which may result in a malfunction. 5. Re-install the lamp cover and tighten the screw. Do not turn on the power with lamp cover removed. Whenever the lamp has been replaced, reset the total operation time of the lamp. Do not reset if the lamp was not replaced, as this could cause breakage.

Note: For maximum lamp life, do not shock, handle or scratch the lamp glass when it is hot. Also, do not use an old or previously used lamp as a replacement lamp.


When ordering a lamp, use the part number that references the projector model number.
Note: To determine projector model number, look at the bottom cover label only.

r e b m u N l e d o M r o t c e j o r P r e b m u N tr a P p m a L
0 3 7 7 P M 1 - 6 3 0 9 - 9 6 9 6 - 8 7
B 0 3 7 7 P M 9 - 7 9 2 9 - 9 6 9 6 - 8 7


Please do the following within 10 minutes from turning power on if you replace the lamp after 1500 hours.

2, Press - Keystone + to display the lamp usage on the bottom of the screen. Press again to select “Reset.”

S M E L B O R P S N O I T U L O S
.t elni C A e h t o t ni d r o c r e w o p e h t g ul P .t elni r e w o p e h t o t ni d r o c r e w o p e h t g ul P . n o k c a b ti g nin r u t e r o f e b r o tc ejo r p e h t ff o g nin r u t r e tf a s e t u ni m 2 tia W
.tc ejo r p o t e c r u o s t u p ni r e p o r p e h t d e tc ele s e v a h u o y t a h t k c e h C .ylr e p o r p d e tc e n n o c e r a s elb a c lla t a h t e r u s n E .ts a rt n o c d n a s s e n t h gir b e h t ts ujd A . p a c s n el e h t e v o m e R
E R U T C I P O N
N O E R A U Q S T ' N S I E G A M I
. n e e r c s e h t o t elg n a sti e v o r p m i o t tin u e h t n oitis o p e R ? n oitc n u f e n o ts y e k e h t g nis u d e tc e rr o c ylr e p o r p t e sff o la citr e v e h t sI
R O L O C R O O P. m e ts y s o e div tc e rr o c e h t tc ele S . n oit a r u t a s d n a ,ts a rt n o c ,s s e n t h gir b e h t ts ujd A
.s u c o f e h t ts ujd A . n e e r c s e h t o t elg n a sti e v o r p m i o t tin u e h t n oitis o p e R e h t nih ti w si n e e r c s e h t d n a tin u e h t n e e w t e b e c n a tsid e h t t a h t e r u s n E .s n el e h t f o e g n a r t n e m ts ujd a
D E R R U L B S I E G A M I
.s e n o w e n h ti w s eir e tt a b e h t e c alp e R .tin u e h t d n a lo rt n o c e t o m e r e h t n e e w t e b s elc a ts b o o n e r a e r e h t e r u s e k a M .tin u e h t f o )t e e f 3 1 ( s r e t e m 4 nih ti w lo rt n o c e t o m e r e t a r e p O . d a p lo rt n o c e h t n o r e vie c e r e h t s k c olb g nih t o n e r u s e k a M
L O R T N O C E T O M E R
K R O W T ' N S E O D
. e c r u o s t u p ni oid u a m o rf n oitc e n n o c elb a c oid u a e h t k c e h C . e c r u o s oid u a e h t ts ujd A . n o tt u b ) + ( E M U L O V s s e r P . n o tt u b E T U M s s e r P

d e y a l p s i D e g a s s e M ) e l b a c il p p a fi , n o it u l o S d n a ( g n i n a e M
G N I H C R A E S.la n gis t u p ni yfit n e dit o n n a c r o tc ejo r P
, D E T C E T E D L A N G I S T U P N I
E G A M I O T U A G N I T A V I T C A.la n gis t u p ni d eifit n e di s a h r o tc ejo r P
E G N A R F O T U O S I C N Y S e h t f o e g n a r e h t s d e e c x e y c n e u q e rfla t n o zir o h s'la n gis t u p ni e h T
.s'r o tc ejo r p
D N A P M A L E H T E G N A H C
e b o t s d e e n d n a s r u o h 0 0 2 1 r e v o r o f d e t a r e p o n e e b s a h p m al e h T
R E M I T P M A L E H T T E S E R
. n o o s d e c alp e r
, P M A L E H T E G N A H C
ff o t u h s lli w r e w o p e h t d n a s r u o h 9 7 4 1 r o f d e t a r e p o n e e b s a h p m al e h T
F F O N R U T L L I W R E W O P E H T
. elbis s o p s a n o o s s a p m al e h t e c alp e R .s r u o h e r o m 0 2 r e tf a
. S R U O H 0 2 R E T F A
! P M A L E H T E G N A H C
lli w r e w o P .s r u o h 0 0 5 1 r e v o r o f d e t a r e p o n e e b s a h p m al e h T
) d e r g nit h gil D E L h ti w , g nik nilb (
.yle t aid e m m i p m al e h t e c alp e R .s e t u ni m 0 1 niff o t u h s ylla cit a m o t u a

Description Part Number
Power Cord (EU) DY-0205-1354-4 Power Cord (US) DY-0205-1356-9 Power Cord (UK) DY-0205-1355-1 Adapter, PS/2 Mouse 78-8118-8395-4 Adapter, ADB (Apple Desktop Bus) Mouse 78-8118-8397-0 Adapter, Serial Mouse 78-8118-8396-2 General Cable 78-8118-8394-7 VGA Cable 78-8118-3401-5 Mac Adapter (switchable) 78-8118-3308-2 150W Lamp 78-6969-9036-1 Remote Control 78-8118-8398-8 Soft-side Carrying Case 78-6969-9034-6 Lens Cover 78-8118-8399-6
Description Part Number
NTSC Optional Video Module (RCA with Tuner) 78-6969-9038-7 PAL Optional Video Module (SCART) 78-6969-9104-7 3-Conductor Video/Audio Cable 78-8118-3234-0 Stereo Mini-Jack Cable 78-8118-8290-7 S-Video Cable 78-8118-3538-1 SCART-RCA Adapter DY-0205-1011-0
For product information, product assistance, service information, or to order accessories, please contact 3M Customer Service at the following number:
The contents of this manual are subject to revision without prior notice.
3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual.
Reproduction of this manual in any form without prior permission is strictly prohibited.
3M will replace the manual if any pages are missing or collated incorrectly.

Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M.
Warranty and Limited Remedy. This product will be free from defects in material and manufacture for a period of two years from the date of purchase. Exclusion to Warranty: The lamps are considered a consumable item and are warrantied for 90 days or 180 hours, whichever occurs first. 3M MAKES NO OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Limitation of Liability. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted.
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we’re the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
3M Canada P.O. Box 5757 London, Ontario N6A 4T1
3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico
3M Europe Boulevard de l’Oise 95006 Cerge Pontoise Cedex France
Litho in USA Copyright © 2001 3M IPC.
All Rights Reserved 78-6970-9063-3 Rev. A
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| NO POWER | Plug the power cord into the AC inlet. Plug the power cord into the power inlet. Wait 2 minutes after turning off the projector before turning it back on. | p.33 | |
| NO PICTURE | Check that you have selected the proper input source to project. Ensure that all cables are connected properly. Adjust the brightness and contrast. Remove the lens cap. | p.33 | |
| IMAGE ISN'T SQUARE ON SCREEN | Reposition the unit to improve its angle to the screen. Is the vertical offset properly corrected using the keystone function? | p.33 | |
| POOR COLOR | Select the correct video system. Adjust the brightness, contrast, and saturation. | p.33 | |
| IMAGE IS BLURRED | Adjust the focus. Reposition the unit to improve its angle to the screen. Ensure that the distance between the unit and the screen is within the adjustment range of the lens. | p.33 | |
| REMOTE CONTROL DOESN'T WORK | Replace the batteries with new ones. Make sure there are no obstacles between the remote control and the unit. Operate remote control within 4 meters (13 feet) of the unit. Make sure nothing blocks the receiver on the control pad. | p.33 | |
| NO SOUND | Check the audio cable connection from audio input source. Adjust the audio source. Press VOLUME (+) button. Press MUTE button. | p.33 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.