Instruction/ maintenance manual of the product RMC-KFA210T Dyna-Glo
Go to page of 28
CFM RMC INTERNA TIONAL 3501 W . HOW ARD ST ., SKOKIE, IL 60076 1-800-527-4948 POR T ABLE FORCED AIR HEA TERS “USER’S MANUAL” Before the first use of this heater , please read this USER’S MANUAL very carefully .
1 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! DANGER - IMPROPER USE OF THIS HEATER CAN RESULT IN SERIOUS INJURY OR DEATH FROM BURNS, FIRE, EXPLOSION, ELECTRICAL SHOCK AND/OR CARBON MONOXIDE POISONING. W ARNINGS: 1. RISK OF INDOOR AIR POLLUTION! • Use this heater only in well ventilated areas.
2 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! ITEM P AGE # PRECAUTIONS - SAFETY GUIDE 1 1. INTRODUCTION 2 2. FEA TURES 2 3. UNP ACKING AND ASSEMBL Y 4 4. KEROSENE (1-K OR NO. 1 FUEL OIL) 6 5. OVER VIEW OF HEA TER DESIGN 7 6. FUELING YOUR HEA TER 8 7.
3 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! Figure 2. RMC-KFA120T / RMC-KFA170T MODELS Figure 2. RMC-KFA210T MODEL Hot Air Outlet Handle Upper Shell Lower Shell Fuel Gauge Side Cover Power/R.
4 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! Figure 5. RMC-KFA120T / RMC-KFA170T / RMC-KFA210T MODELS Handle Screws Wheels Split pin And Flat W asher Screws And Nuts Handle Wheel Support Frame Axle 3. UNP ACKING AND ASSEMBL Y 1. REMOVE THE HEATER AND ALL PACKING MATERIALS FROM THE BOX.
5 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 2. ASSEMBLY A. For RMC-KFA45T/RMC-KFA65T Models only (Figure 6) Tools Required • Medium Phillips Screwdriver 1. Align the holes on the upper shell with the 2 mounting holes on the handle as shown in Figure 6.
6 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! Screw Air Inlet Axle Split pin Flat W asher Wheel Nut Wheel Support Frame Fuel T ank Flange Hot Air Outlet Handle Extended Hub 4. KEROSENE (1-K) It is EXTREMELY IMPORTANT for the proper operation of this heater that you use the correct grade of kerosene.
7 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 5. OVER VIEW OF HEA TERS DESIGN Fuel System: This heater is equipped with an electric air pump that forces air through the air line connected to the fuel intake and then through a nozzle in the burner head.
8 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 6. FUELING YOUR HEA TER NEVER FILL THE HEATER FUEL TANK IN THE LIVING SPACE: FILL THE TANK OUTDOORS. DO NOT OVERFILL YOUR HEATER AND BE SURE HEATER IS LEVELED. IMPORTANT NOTICE REGARDING FIRST IGNITION OF HEATER: The first time you light the heater, it should be done outdoors .
9 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! Figure 10 TO STOP HEATER 1. Turn switch to “OFF” and unplug power cord. TO RESTART HEATER 1.Wait 10 seconds after stopping heater. 2. Repeat steps under to start heater . 8. LONG TERM ST ORAGE OF YOUR HEA TER 1.
C.) AIR OUTPUT FIL TER, LINT FIL TER REPLACE EVERY 500 HOURS OF OPERATION OR ONCE A YEAR. - Remove upper shell and fan guard (See page 9). - Remove end filter cover screws using medium phillips screwdriver. - Remove end filter cover. - Replace air output and lint filter.
11 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! Figure 15. Figure 14. F .) SP ARK PLUG CLEAN AND REGAP EVERY 600 HOURS OPERATION OR REPLACE AS NEEDED. (For RMC-KFA 45T/65T/120T/170T Models Only) - Remove upper shell (See page 9). - Remove fan (See page 10).
12 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! (For RMC-KFA 210T Models Only) - Remove upper shell (See page 9). - Remove fan (See page 10). - Remove ignitor wire from spark plug. - Remove spark plug from bracket-spark using medium phillips screwdriver.
13 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! H .) FUEL FIL TER CLEAN OR REPLACE TWICE A HEATING SEASON OR AS NEEDED. (For RMC-KFA 45T/65T/120T/170T Models Only) - Remove side cover screws using medium phillips screwdriver. - Remove side cover.
14 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! I) FUEL VALVE ( For RMC-KFA210T Model only) - Remove side cover screws using medium phillips screwdriver (See page 13). - Remove upper shell (See page 9). - Remove fan (See page 10). - Pull fuel line (lower and upper) off the fuel valve fittings (See figure 21).
15 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! I .) PUMP PRESSURE ADJUSTMENT - Remove pressure gauge plug from end filter cover. - Install accessory pressure gauge. - Start heater (See Operation, page 8) Allow motor to reach full speed - Adjust pressure (Using a flat blade screwdriver) Turn relief valve to right to increase pressure.
16 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 10 . TROUBLE SHOOTING GUIDE Heater ignites but MAIN PCB 1. Wrong pump pressure 1. See Pump Pressure Adjustment, assembly shuts heater off after page 15. a short period of time. 2. Dirty Air Output, Air Intake 2.
17 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 11 . WIRING DIAGRAM A) WIRING DIAGRAM (RMC-KFA45T / RMC-KFA65T) B) WIRING DIAGRAM (RMC-KFA120T).
18 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 11 . WIRING DIAGRAM C) WIRING DIAGRAM (RMC-KFA170T) D) WIRING DIAGRAM (RMC-KFA210T).
19 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 12 . SPECIFICA TIONS RMC-KFA45T / RMC-KFA65T RMC-KFA120T / RMC-KFA170T / RMC-KFA210T 24.75" 39" 20.5" KF A120T KF A170T KF A210T 23" 19" 33.5" H D W MODEL RMC-KFA45T RMC-KFA65T RMC-KFA120T RMC-KFA170T RMC-KFA210T BTU/Hr .
NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 13 . EXPLODED P AR TS DRA WING (RMC-KF A45T/65T/120T/170T Models Only) NOTE: SPECIFY MODEL NUMBER AND PART NUMBER WHEN ORDERING PARTS.
21 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 13 . EXPLODED P AR TS DRA WING (RMC-KF A 210T Model Only) 34 35 Fuel Valve Assembly 17 31 32 27 28 24 27-1 25 21 18 26 21 23 14-4 14-2 14-5 14-1 .
22 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 14 . P AR TS LIST (RMC-KF A 45T/65T/120T/170T Models Only) KEY NO. DESCRIPTION PART NO. RMC-KFA45T RMC-KFA65T RMC-KFA120T RMC-KFA170T 1 Fuel Tank.
KEY NO. DESCRIPTION PART NO. RMC-KFA45T RMC-KFA65T RMC-KFA120T RMC-KFA170T 22-6 Rotor Kit FA1000 FA1000 FA1000 FA1000 22-7 Blade See 22-6 See 22-6 See 22-6 See 22-6 22-8 End Pump Cover 3531-0008-00 35.
24 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 14 . P AR TS LIST (RMC-KF A 210T Model Only) KEY No. P AR T No. RMC-KF A210T DESCRIPTION 2151-0001-00 2156-0001-00 2155-0001-00 2151-0003-00 3980.
25 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! ACCESSORIES Air Pressure Gauge F A1010 (all models) Thermostat F A1012 (all models) FOR TECHNICAL ASSIST ANCE SEE YOUR LOCAL RET AILER OR CONT ACT US A T : Phone: 1-800-527-4948 KEY No. P AR T No.
1 2 1 2 3 5 9 6 7 8 4 NEVER LEA VE THE HEA TER UNA TTENDED WHILE BURNING! 14 . P AR TS LIST (WHEELS AND HANDLE) 1) RMC-KF A45T/65T MODELS 2) RMC-KF A120T/170T/210T MODEL KEY NO. DESCRIPTION PART NO. RMC-KFA45T RMC-KFA65T QTY 1 Handle 3231-0073-00 3231-0073-00 1 2 Screw 4319-0015-00 4319-0015-00 2 KEY NO.
4221 - 0059- 00 07/03 Rev. 00 EDITION 2003.
An important point after buying a device Dyna-Glo RMC-KFA210T (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dyna-Glo RMC-KFA210T yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dyna-Glo RMC-KFA210T - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dyna-Glo RMC-KFA210T you will learn all the available features of the product, as well as information on its operation. The information that you get Dyna-Glo RMC-KFA210T will certainly help you make a decision on the purchase.
If you already are a holder of Dyna-Glo RMC-KFA210T, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dyna-Glo RMC-KFA210T.
However, one of the most important roles played by the user manual is to help in solving problems with Dyna-Glo RMC-KFA210T. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dyna-Glo RMC-KFA210T along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
