Instruction/ maintenance manual of the product 8D0095 Digicom
Go to page of 9
http://www .digicom.it User's Guide rev. 1.0 05/2000 HDSL.
HDSL INDEX - DECLARA TION CE OF CONFORMITY I INDEX INTRODUCTION III PRE F ACE III 1 . GENERAL 1.1 1.1 . DESCRIPTION 1.1 1.2 . FRONT P ANE L VIEW 1.1 1.3 . REAR P ANE L VIEW 1.2 1.3.1 . LINE CONNEC T OR PIN 1.2 1.3.2 . G.703 120 OHM CONNEC T OR PIN 1.2 2 .
HDSL PREF ACE III INTRODUCTION Digicom’s HDSL modems uses the HDSL technology (High-bit-rate Digital Subscriber Line) that allows very high transfer speeds (2 Mbps) over leased lines. It is possible to connect Digicom’s HDSL modems either over 2 wires and 4 wires lines.
HDSL GENERAL 1.1 1. GENERAL 1.1. DESCRIPTION TX RX G.703/V35 MASTER TX RX G.703/V35 SLAVE HDSL line 2/4 wires R HIGH SPEED MODEM K1 K2 /G703 T/SLV P LOC M REM PW LIN LIN V35 MS LOO ALM AL HDSL R HIGH .
HDSL GENERAL 1.2 1.3. REAR P ANEL VIEW TX RX G703 75 Ω 120 / 75 Ω G703 120 Ω V.35 LINE CONFIG PWR Picture 3 Name Function PWR Power supply CONFIG 9pin female connector for device configuration LINE HDSL line connector RJ1 1 4 contacts G.703 120 ohm G.
HDSL INST ALLA TION 1.1 2. INST ALLA TION l Remove the two HDSL modems from the package and check they are OK. l Using the “SetHDSL” program, configure one of the two modems as Slave. l Connect the HDSL lines between the modems (RJ1 1 connector). l Power on the modems that will connect using the factory configuration (default): V .
HDSL INST ALLA TION 1.2 NOTE: For further and complete information on the “SetHDSL”, please refer to the program help on line..
HDSL INST ALLA TION 1.3 Interface speed “N” Line speed f or each couple Line speed [Kbit/s] Time Slot of wire (4 wires) (2 wires) [Kbit/s] [Kbit/s] 64 1 272 272 128 2 272 272 192 3 272 272 256 4 2.
21010 Cardano al Campo V A via A. V olta 39.
An important point after buying a device Digicom 8D0095 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Digicom 8D0095 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Digicom 8D0095 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Digicom 8D0095 you will learn all the available features of the product, as well as information on its operation. The information that you get Digicom 8D0095 will certainly help you make a decision on the purchase.
If you already are a holder of Digicom 8D0095, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Digicom 8D0095.
However, one of the most important roles played by the user manual is to help in solving problems with Digicom 8D0095. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Digicom 8D0095 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
