Instruction/ maintenance manual of the product DE30WGB DeLonghi
Go to page of 28
distributed by DèLonghi Pty Ltd INST ALLA TION and SER VICE INSTRUCTIONS USE and CARE INSTRUCTIONS BUIL T -IN GAS HOBS Models: DE 30 W GB - DE 30 2 G B.
2 Dear Customer , Thank you for having pur chased and given your pr efer ence to our pr oduct. The safety pr ecautions and r ecommendations r eported below ar e for your own safety and that of others. They will also pr ovide a means by which to make full use of the featur es offer ed by your appliance.
3 IMPORT ANT PRECAUTIONS AND RECOMMENDA TIONS FOR USE OF ELECTRICAL APPLIANCES Use of any electrical appliance implies the necessity to follow a series of fundamental rules.
4 INST ALLA TION CAUTION: ■ This appliance must be installed in accor dance with these installation instructions, local gas fitting r egulations, municipal building codes, water supply r egulations, electrical wiring regulations, - Gas Installations and ony other r elevant statutory regulations.
N.B. The connection of the appliance to earth is mandatory . If the installation r equires alterations to the domestic electrical system call a qualified electrician. He should also check that the socket cable section is suitable for the power drawn by the appliance.
6 Figur e 3 Important note: This appliance shall not be used as a space heater , especially if installed in marine craft or caravans. CLEARANCES: Installation clearances and pr otection of combustible surfaces shall comply with the curr ent local regulations e.
7 The installation shall comply with the dimensions in Figur es 3 and 4, bearing in mind that: ■ A partition between the base of the hob and the cupboar d below should be fitted 0 mm below the workbench surface if the cupboar d is to be used for storage.
Figur e 6 Figur e 7 8 3 cm min 3 cm 4 cm S A R Adhesive side G G R R F ASTENING THE COOKTOP Each cooktop is provided with an instal- lation kit including brackets and scr ews for fasten ing the cookto p to ben ches from 30 to 40 mm thick.The kit includes four R bracke ts and four self-thr eading screws S (figs.
GAS SUPPL Y : ■ This appliance is suitable for use with Natural Gas or ULPG . (Check the “gas type” sticker attached to the appliance). ■ For Natural Gas the gas supply must be r egulated to obtain a pressur e of 1 kPa with t burners operating.
5. Check the minimum burner setting by quickly r otating the gas control knob fr om the maximum to the minimum position, the flame must not go out. If adjust- ment is r equired carry out the “minimum burner setting adjustment" pr ocedure described below .
(Note: Gas type sticker and data plate ar e attached to the underside of the base of the appliance.) T ABLE FOR THE CHOICE OF THE INJECTORS Natural Gas ULPG T est Point 1.0 2.75 Pr essure (kPa) Burner Injector Orifice Gas Consumption Injector Orifice Gas Consumption [mm] [MJ/h] [mm] [MJ/h] Semi-rapid 1.
Figur e 11 Figur e 12 12 CONVERSION PROCEDURE (to convert to Natural gas or to ULPG) REPLACING THE INJECTORS The conversion pr ocedure must be carried out only by an authorised person. This appliance is suitable for use with Natural gas or Universal LPG (check the “gas type” sticker attached to the appliance).
Figur e 13 13 MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spr eads to all burner ports when the burner is lit with the gas tap set to the minimum position.
USE and CARE CAUTION: ■ This appliance must be used only for the task it has explicitly been designed for , that is for domestic cooking of foodstuffs. Any other form of usage is to be consider ed as inappropriate and ther efor e dangerous. Do not use this appliance as a space heater .
LIGHTING GAS BURNERS ■ Check that the electricity is switched on to allow spark ignition. ■ Make sur e that all controls ar e turned to zer o. ■ The gas flow to the burner is contr olled by a tap incorporating a safety cut-off valve. If the burner flame should go out for some r eason, the safety valve will automatically stop the gas flow .
LIGHTING GAS BURNERS (FITTED WITH SAFETY CUT -OFF VAL VE) In or der to light the burner , you must: 1 – T urn the knob fig. 1 7 in anti-clockwise dir ection up to the maximum aperture, push in and hold the knob; this will light the gas. If ther e is no mains electrical supply , bring a lighted match close to the burner .
CORRECT USE OF TRIPLE-RING BURNER - DE30W GB model only ■ The flat-bottomed pans ar e to be placed directly onto the pan-support. ■ T o use the WOK you must place the wok stand in the CORRECT position as shown in fig.
Cleaning and Maintenance 18 GENERAL ADVICE ✓ Before you begi n cleaning you must ensure that the hob is switched of f. ✓ It is advisable to clean when the appliance is cold and especially when cleaning the enamelled parts.
ENAMELLED P ARTS ✓ All the enamelled parts must be cleaned with a sponge and soapy water only or other non-abrasive products. ✓ Dry preferably with a soft cloth. ✓ If acid substances such as lemon juice, tomato conserve, vinegar etc. ar e left on the enamel for a long time they will etch it, making it opaque.
IMPORT ANT W ARNING NEVER unscrew the bur ner plate fixing screws (fig. 22). The burner plates can be removed ONL Y by an authorised service agent. Damage to the appliance will occur if not observing this condition and this may result in serious injury to the user .
BURNERS AND GRIDS ✓ These parts can be removed and cleaned with appropriate pr oducts. ✓ After cleaning, the burners and their flame spreaders must be well dried and correctly replaced. ✓ It is very important to check that the bur ner flame spr eader and the cap have been cor - rectly positioned.
CORRECT POSITIONING OF THE SEMIRAPID AND RAPID BURNERS ✓ It is very important to check that the burner flame spreader “F” and the cap “C” have been correctly positioned (see figs. 23 24 and ). They shall be level and must not ro- tate. Failure to do so can cause serious problems.
A B Flame failure probe " T " Ignitor " S " CORRECT POSITIONING OF THE TRIPLE RING BURNER Figur e 26 Figure 27 Figure 28 Figure 29 ✓ The triple rin g burner must be corr ectly posi tioned (see fig. 26 ); the b urner rib s must be fitted in their housing as shown by the arrow .
SERVICE AND MAINTENANCE If the ignition spark fails to ignite or does not light the gas, check the following items befor e calling our Customer Service Centre to obtain the near est Authorised Delonghi Service Agent: ■ Burner is r eassembled and located correctly .
25.
26.
Descriptions and illustrations in this booklet are given as simply indicative. The manufactur er reserves the right, considering the characteristics of the models described here, at any time and without notice, to make eventual necessary modifications for their construction or for commercial needs.
cod. 1103 763 ß 1.
An important point after buying a device DeLonghi DE30WGB (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought DeLonghi DE30WGB yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data DeLonghi DE30WGB - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, DeLonghi DE30WGB you will learn all the available features of the product, as well as information on its operation. The information that you get DeLonghi DE30WGB will certainly help you make a decision on the purchase.
If you already are a holder of DeLonghi DE30WGB, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime DeLonghi DE30WGB.
However, one of the most important roles played by the user manual is to help in solving problems with DeLonghi DE30WGB. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device DeLonghi DE30WGB along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
