
Mini Tower Computer
Desktop Computer
Small Form Factor Computer

HyperTransport™ and Dual-Core Technology
Trusted Platform Module (TPM)
Booting to a USB Device
Enabling Cool 'n' Quiet™ Technology
LegacySelect technology control offers legacy-full, legacy-reduced, or legacy-free solutions based on common platforms, hard-drive images, and help desk procedures. Control is provided to the administrator through system setup, Dell OpenManage™ IT Assistant, or Dell custom factory integration.
LegacySelect allows administrators to electronically activate or deactivate connectors and media devices that include serial and USB connectors, a parallel connector, a floppy drive, PCI slots, and a PS/2 mouse. Connectors and media devices that are deactivated make resources available. You must restart the computer to effect the changes.
Alert Standard Format
ASF is a DMTF management standard that specifies "pre-operating system" or "operating system-absent" alerting techniques. The standard is designed to generate an alert on potential security and fault conditions when the operating system is in a sleep mode or the system is turned off. ASF is designed to supersede previous operating-system-absent alerting technologies.
Your computer supports the following ASF version 1.03 and 2.0 alerts and remote capabilities:
For more information about Dell's ASF implementation, see the ASF User's Guide and the ASF Administrator's Guide, which are available on the Dell Support website at support.dell.com.
IT Assistant configures, manages, and monitors computers and other devices on a corporate network. IT Assistant manages assets, configurations, events (alerts), and security for computers equipped with industry-standard management software. It supports instrumentation that conforms to SNMP, DMI, and CIM industry standards.
Dell OpenManage Client instrumentation, which is based on DMI and CIM, is available for your computer. For information on IT Assistant, see the Dell OpenManage IT Assistant User's Guide available on the Dell Support website at support.dell.com.
Dell OpenManage Client Instrumentation is software that enables remote management programs such as IT Assistant to do the following:
l Access information about your computer, such as how many processors it has and what operating system it is running.
l Monitor the status of your computer, such as listening for thermal alerts from temperature probes or hard-drive failure alerts from storage devices.
l Change the state of your computer, such as updating its BIOS or shutting it down remotely.

A managed system is one that has Dell OpenManage Client Instrumentation set up on a network that uses IT Assistant. For information about Dell OpenManage Client Instrumentation, see the Dell OpenManage Client Instrumentation User's Guide available on the Dell Support website at support.dell.com.
Chassis Intrusion Detection
This feature, if installed and enabled, detects that the chassis was opened and alerts the user. To change the Chassis Intrusion setting:
l On — If the computer cover is opened, the setting changes to Detected, and the following alert message displays during the boot routine at the next
computer start-up:
Alert! Cover was previously removed.
To reset the Detected setting, enter system setup (see Entering System Setup). In the Chassis Intrusion option, press the left- or right-arrow key to select Reset, and then choose On, On-Silent, or Off.
l On-Silent (default setting) — If the computer cover is opened, the setting changes to Detected. No alert message appears during the boot sequence
at the next computer start-up.
l Off — No intrusion monitoring occurs and no messages appear.
Use one of the following methods to secure your computer:
l Use a padlock alone or a padlock and looped security cable with the padlock ring.
A padlock alone prevents the computer from being opened.
A security cable looped around a stationary object is used in conjunction with a padlock to prevent unauthorized movement of the computer.
l Attach a commercially available antitheft device to the security cable slot on the back of the computer.
Antitheft devices usually include a segment of metal-stranded cable with an attached locking device and key. The documentation that comes with the device contains instructions for installing it.

You cannot change or enter a new system password if either of the following two options is displayed:
l Set — A system password is assigned.
l Disabled — The system password is disabled by a jumper setting on the system board.
You can only assign a system password when the following option is displayed:
l Not Set — No system password is assigned and the password jumper on the system board is in the enabled position (the default setting).
The option heading changes to Enter Password, followed by an empty 32-character field in square brackets.
You can use up to 32 characters. To erase a character when entering your password, press or the left-arrow key. The password is not case sensitive.
Certain key combinations are not valid. If you enter one of these combinations, the speaker emits a beep.
As you press each character key (or the spacebar for a blank space), a placeholder appears in the field.
If the new system password is less than 32 characters, the whole field fills with placeholders. Then the option heading changes to Verify Password, followed by another empty 32-character field in square brackets.
The password setting changes to Set.
Password protection takes effect when you restart the computer.
When you start or restart your computer, the following prompt appears on the screen.
If Password Status is set to Locked:
Type the password and press .
If you have assigned an administrator password, the computer accepts your administrator password as an alternate system password.
If you type a wrong or incomplete system password, the following message appears on the screen:
** Incorrect password. **
If you again type an incorrect or incomplete system password, the same message appears on the screen. The third and subsequent times you type an incorrect or incomplete system password, the computer displays the following message:
** Incorrect password. ** Number of unsuccessful password attempts: 3 System halted! Must power down.
Even after your computer is turned off and on, the previous message is displayed each time you type an incorrect or incomplete system password.

If Not Set is displayed, the system password is deleted. If Not Set is not displayed, press , press the left- and right-arrow keys to highlight Save/Exit, and then press to restart the computer and implement your changes. Then repeat steps 3 and 4.
You cannot change or enter a new administrator password if either of the following two options is displayed:
l Set — An administrator password is assigned.
l Disabled — The administrator password is disabled by a jumper setting on the system board.
You can only assign an administrator password when the following option is displayed:
l Not Set — No administrator password is assigned and the password jumper on the system board is in the enabled position (the default setting).
The administrator password can be the same as the system password.
The computer prompts you to type and verify the password. If you enter a character that is not permitted, the computer emits a beep.
After you verify the password, the Admin Password setting changes to Set. The next time you enter system setup, the computer prompts you for the administrator password.
A change to Admin Password becomes effective immediately (no need to restart the computer).
When you enter system setup, the Admin Password option is highlighted, prompting you to type the password (see Entering System Setup).
If you do not type the correct password, the computer lets you view, but not modify, system setup options.

To change an existing administrator password, you must know the administrator password.
The setting changes to Not Set.
To assign a new administrator password, perform the steps in Assigning an Administrator Password.
To reset system and/or administrator passwords, see Clearing Forgotten Passwords.
TPM is a hardware-based security feature that can be used to create and manage computer-generated encryption keys. When combined with security software, the TPM enhances existing network and computer security by enabling features such as file protection capabilities and protected e-mail. The TPM feature is enabled through a system setup option.
a. Restart the computer and press during the Power On Self Test to enter the system setup program. b. Select Security, then select TPM Security and press . c. Under TPM Security, select On. d. Press to exit the setup program. e. If prompted, click Save/Exit. 2. Activate the TPM setup program:
a. Restart the computer and press during the Power On Self Test to enter the system setup program. b. Select Security, then select TPM Activation and press . c. Under TPM Activation, select Activate and press .
Once the process is complete, the computer either restarts automatically or prompts you to restart your computer.
Overview
Use system setup as follows:
l To change the system configuration information after you add, change, or remove any hardware in your computer
l To set or change a user-selectable option such as the user password

l To read the current amount of memory or set the type of hard drive installed
Before you use system setup, it is recommended that you write down the system setup screen information for future reference.
The system setup screen displays current or changeable configuration information for your computer. Information on the screen is divided into four areas: the menu at the top, the main window, the Item Help field on the right, and key functions listed on the bottom.
Options List — This field appears on the left side of the system setup window. The field is a scrollable list containing features that define the configuration of your computer, including installed hardware, power conservation, and security features.
Option Field — This field contains information about each option. In this field you can view your current settings and make changes to your settings.
Scroll up and down the list by using the up- and down-arrow keys. As an option is highlighted, the Option Field displays more information about that option and the option's current and available settings.
Use the right- and left-arrow keys to highlight an option. Press to make that selection active.
Key Functions — This field appears below the Option Field and lists keys and their functions within the active system setup field.
Diskette Drive This option enables or disables the floppy drive. The options are Off, USB, Internal, and Read Only.
Drives

Primary This setting specifies which video controller is primary when there are two video controllers available (PCI, Onboard, Auto, and PEG). This
(Internal default) · Video

selection only matters if there are two video controllers present. When Auto is selected, the add-in video controller will be used.
This setting configures the amount of system memory that is reserved for the integrated video controller. The settings are Auto, 16MB, 32MB, 64MB, 128MB, or Off.
HDD Acoustic Mode (Bypass default) l Bypass — Your computer does not test or change the current acoustics mode setting.
l Quiet — The hard drive operates at its most quiet setting.
l Suggested — The hard drive operates at the level suggested by the drive manufacturer.
l Performance — The hard drive operates at its maximum speed.
Sets time to automatically turn on the computer.
Time is kept in the standard 12-hour format (hours:minutes). Change the startup time by pressing the right- or left-arrow key to increase or

decrease the numbers, or type numbers in both the date and time fields.
You can use this feature, for example, to restart your computer to a USB device, such as a floppy drive, memory key, or CD-RW drive.
If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft Windows desktop, then shut down your computer (see Turning Off Your Computer) and try again.
The Boot Device Menu appears, listing all available boot devices.

The BIOS detects the device and adds the USB device option to the boot menu.
The computer boots to the USB device.
Mini Tower, Desktop, and Small Form Factor Computers


1. Follow the procedures in Before You Begin. 2. If clearing the password on a small form factor computer, remove the hard drive (see Drives). 3. Locate the 2-pin password jumper (PSWD) on the system board, and remove the jumper to clear the password (see Jumper Settings). 4. If clearing the password on a small form factor computer, install the hard drive (see Drives). 5. Replace the computer cover (see Replacing the Computer Cover). 6. Connect your computer and monitor to electrical outlets, and turn them on. 7. After the Microsoft® Windows® desktop appears on your computer, shut down your computer. (see Turning Off Your Computer) 8. Turn off the monitor and disconnect it from the electrical outlet. 9. Disconnect the computer power cable from the electrical outlet, and press the power button to ground the system board. 10. Open the computer cover (see Removing the Computer Cover for mini tower computers, Removing the Computer Cover for desktop computers and Removing the Computer Cover for small form factor computers). 11. Remove the hard drive (Removing a Hard Drive). 12. Locate the 2-pin password jumper on the system board and attach the jumper to reenable the password feature. 13. Replace the hard drive (Installing a Hard Drive). 14. Replace the computer cover (see Replacing the Computer Cover).

a. Locate the password and CMOS jumpers. Password (PSWD) and CMOS (RTC_RST) jumpers are on the system board (see Jumper Settings). b. Remove the password jumper plug from its pins. c. Place the password jumper plug on the RTC_RST pins and wait approximately 5 seconds. d. Remove the jumper plug from the RTC_RST pins and place it back on the password pins. 4. If clearing the CMOS setting on a small from factor computer, install the hard drive (see Installing a Hard Drive). 5. Replace the computer cover (see Replacing the Computer Cover).
HyperTransport technology can increase overall computer performance by removing I/O bottlenecks, increasing system bandwidth, and reducing system latency. A fully integrated DDR memory controller allows a direct connection between the processor and the main memory. Dual-Core is a technology in which two physical computational units exist inside a single processor package, thereby increasing computing efficiency and multi-tasking ability.
While many programs can benefit from HyperTransport and dual-core technology, some programs may have not been optimized for them and may require an update from the software manufacturer. Contact the software manufacturer for updates and information about using HyperTransport or dual-core technology with your software. To determine if your computer is using HyperTransport technology, check the system setup option for HyperTransport under the Performance tab (see System Setup).
Your computer can be set to use less power when you are not working. You control the power usage through the operating system installed on your computer and certain option settings in system setup. These periods of reduced power are called "sleep modes."
l Standby. In this sleep mode, power is reduced or turned off for most components, including the cooling fans. However, system memory remains active.
l Hibernate. This sleep mode reduces power consumption to a minimum by writing all data in system memory to a hard drive and then removing system
power. Waking up from this mode restarts the computer, and the memory contents are restored. Operation then resumes where the computer left off when it entered the hibernation mode.
l Shutdown. This sleep mode removes all power from the computer except a small auxiliary amount. As long as the computer remains connected to an
electrical outlet, it can be automatically or remotely started. For example, the Auto Power On option in system setup allows the computer to automatically start at a specified time. Also, your network administrator can remotely start your computer using a power management event such as Remote Wake Up.
The following table lists the sleep modes and the methods you can use to wake the computer from each mode.

Sleep Mode Wake-Up Methods (Windows XP)
Standby l Press the power button
l Auto power on
l Move or click the mouse
l Type on the keyboard
l USB device activity
l Power management event
Hibernate l Press the power button
l Auto power on
l Power management event
Shutdown l Press the power button
l Auto power on
l Power management event
This section provides an overview of the RAID configuration that you may have selected when you purchased your computer. A number of RAID configurations are available in the computer industry for different types of uses. The Dell mini tower and desktop models of your OptiPlex computer support RAID level 0 and RAID level 1. (RAID support is not available for the small form factor model.) A RAID level 0 configuration is recommended for high-performance programs, while RAID level 1 is recommended for users that desire a high level of data integrity.
The NVIDIA RAID controller on your computer can only create a RAID level configuration using two physical drives. The drives should be the same size to ensure that the larger drive does not contain unallocated (and therefore unusable) space.
Your computer displays information pertaining to your RAID configuration at start-up, before loading the operating system. If RAID is not configured, the message none defined appears under RAID Volumes, followed by a list of the physical drives installed in your computer. If a RAID volume is identified, you can then check the Status field to determine the current state of your RAID configuration. The Status field contains information about the following conditions:
l Normal — Your RAID configuration is functioning properly.
l Degraded — One of your hard drives has failed. The computer is still bootable; however, RAID is not functioning and data is not being copied to the
other drive.
l Rebuild — Following a degraded condition, the computer has detected the replacement/connection of a secondary hard drive and will automatically
restore the RAID configuration the next time the operating system loads.
RAID level 0 uses a storage technique known as data striping to provide a high data-access rate. Data striping is a method of writing consecutive segments, or stripes, of data sequentially across the physical drive(s) to create a large virtual drive. Data striping allows one of the drives to read data while the other drive is searching for and reading the next block.

Another advantage of a RAID level 0 configuration is that it utilizes the full storage capacities of the drives. For example, two 120-GB hard drives combine to provide 240 GB of hard drive space on which to store data.

RAID level 1 uses a data-redundancy storage technique known as mirroring to enhance data integrity. When data is written to the primary drive, the data is also duplicated, or mirrored, on the second drive in the configuration. A RAID level 1 configuration sacrifices high data-access rates for its data redundancy advantages.

If a drive failure occurs, subsequent read and write operations are directed to the surviving drive. A replacement drive can then be rebuilt using the data from the surviving drive.
Your computer can be configured for RAID, even if you did not select a RAID configuration when the computer was purchased. For an explanation of RAID levels and their requirements, see About RAID Configurations. For information on how to install a hard drive, see Installing a Hard Drive for your mini tower computer or Installing a Hard Drive for your desktop computer.
You can use one of two methods to configure RAID hard drive volumes. The first method uses the NVIDIA MediaShield ROM utility and is performed before you install the operating system onto the hard drive. The second method uses NVIDIA MediaShield and is performed after you have installed the operating system and NVIDIA RAID drivers.Both methods require that you set your computer to RAID-enabled mode before you begin.
Hard drives of any size may be used to create a RAID configuration. Ideally, however, the drives should be of equal size to avoid unallocated or unused space. For an explanation of RAID levels and their requirements, see About RAID Configurations. For information on how to install a hard drive, see Installing a Hard Drive for your mini tower computer or Installing a Hard Drive for your desktop computer.

The Define a New Array window appears.
To create a RAID 0 configuration, use the arrow keys to select Striping.
To create a RAID 1 configuration, use the arrow keys to select Mirroring.
The Clear disk data prompt appears.
The Array List window appears.
The Array Detail window appears.
NVIDIA MediaShield allows you to create, view, and manage RAID configurations.
Hard drives of any size may be used to create a RAID configuration using NVIDIA MediaShield. Ideally, however, the drives should be of equal size to avoid unallocated or unused space. For an explanation of RAID levels and their requirements, see About RAID Configurations.
The NVIDIA Create Array Wizard appears and lists the disks that are available for configuration.

The Free Disk Selection window appears.
The Clearing System Data window appears.
The MediaShield RAID management utility window appears and lists the array along with any other installed hard drives.
The NVIDIA Delete Array Wizard appears.
A confirmation screen appears with the name and size of the array that you have marked for deletion.
The MediaShield RAID management utility window appears and lists any remaining arrays along with any other installed hard drives.
NVIDIA MediaShield utilizes a one-step process known as migrating to change the current state of a disk or array without losing any data. If needed, additional hard drives can be added to an existing array, including a single-drive RAID 0 configuration for conversion to a two-drive RAID 0 configuration; however, the capacity of the resulting array must be equal to or greater than the size of the original configuration.
RAID 1 to RAID 1 conversions cannot be performed using the migrating process.

The NVIDIA Convert Array Wizard appears.
The MediaShield RAID management utility window appears and displays the status of the upgrade/migration process along with any other installed hard drives.
If one of the hard drives in a RAID array fails, you can rebuild the array by restoring the data to a replacement drive.
The NVIDIA Rebuild Array Wizard appears.
The MediaShield RAID management utility window appears and displays the status of the rebuild process.
The Cool 'n' Quiet technology controls your computer's processor performance automatically, dynamically adjusting the operating frequency and voltage, according to the task at hand. When an application does not require full performance, significant amounts of power can be saved. performance is designed to still be responsive, with maximum processor performance being delivered when required, and automatic power savings when possible.
Cool 'n' Quiet technology is now enabled.

Replacing the Battery
A coin-cell battery maintains computer configuration, date, and time information. The battery can last several years.
The battery may need replacing if an incorrect time or date is displayed during the boot routine along with a message such as:
Time-of-day not set - please run SETUP program
Invalid configuration information - please run SETUP program
Strike the F1 key to continue, F2 to run the setup utility
To determine whether you need to replace the battery, reenter the time and date in system setup and exit the program to save the information. Turn off your computer and disconnect it from the electrical outlet for a few hours; then reconnect the computer, turn it on, and enter system setup (see Entering System Setup). If the date and time are not correct in system setup, replace the battery.
You can operate your computer without a battery; however, without a battery, the configuration information is erased if the computer is turned off or unplugged from the electrical outlet. In this case, you must enter system setup and reset the configuration options.
To remove the battery:
1. If you have not already done so, make a copy of your configuration information, found in system setup (see System Setup). 2. Follow the procedures in Before You Begin. 3. If you have a Small Form Factor chassis, remove the hard disk drive to access the battery on the system board (see Removing a Hard Drive). 4. Locate the battery socket (see System Board Components for mini tower computers or System Board Components for desktop computers or System Board Components for small form factor computers).
NOTICE: If you pry the battery out of its socket with a blunt object, be careful not to touch the system board with the object. Ensure that the object is inserted between the battery and the socket before you attempt to pry out the battery. Otherwise, you may damage the system board by prying off the socket or by breaking circuit traces on the system board.
a. Support the battery connector by pressing down firmly on the positive side of the connector. b. While supporting the battery connector, press the battery tab away from the positive side of the connector and pry the battery it up out of the securing tabs at the negative side of the connector.
Replacing the Battery · or · or


1 system battery 2 positive side of battery connector 3 battery socket
4 battery socket tab
a. Support the battery connector by pressing down firmly on the positive side of the connector. b. Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector. c. Press the battery straight down into the connector until it snaps into place. 7. If you have a Small Form Factor chassis, install the hard disk drive (see Installing a Hard Drive). 8. Replace the computer cover (see Replacing the Computer Cover). 9. Enter system setup and restore the settings you recorded in step 1 (see Entering System Setup). 10. Properly dispose of the old battery as described in the Product Information Guide.

Turning Off Your Computer
Before Working Inside Your Computer
This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist:
l You have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer.
l You have read the safety information in your Dell™ Product Information Guide.
l A component can be replaced by performing the removal procedure in reverse order.
The procedures in this document may require the following tools:
l Small flat-blade screwdriver
l Flash BIOS update program floppy disk, CD, USB key
a. Save and close any open files, and exit any open programs. b. Click the Start button, and then click Shut Down. c. In the Shut Down Windows window, select Shut down, and then click OK.
The computer turns off after the operating system shutdown process finishes.
If your computer and attached devices did not automatically turn off when you shut down your operating system, turn them off now.
Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.
NOTICE: When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.
Recommended Tools · l Phillips screwdriver

l Remove the mini tower computer cover (see Removing the Computer Cover).
l Remove the desktop computer cover (see Removing the Computer Cover).
l Remove the small form factor computer cover (see Removing the Computer Cover).

Computer, Keyboard, and Monitor
l Use a can of compressed air to remove dust from between the keys on the keyboard.
l To clean your monitor screen, lightly dampen a soft, clean cloth with water. You can also use a special screen-cleaning tissue or solution suitable for the
monitor's antistatic coating.
l Wipe the keyboard, computer, and monitor plastics with a soft cleaning cloth moistened with a solution of three parts water and one part dishwashing
detergent.
Do not soak the cloth or let water drip inside your computer or keyboard.
If your screen cursor skips or moves abnormally, clean the mouse.
1. Clean the outside casing of the mouse with a cloth moistened with a mild cleaning solution. 2. Turn the retainer ring on the underside of your mouse counterclockwise, and then remove the ball. 3. Wipe the ball with a clean, lint-free cloth. 4. Blow carefully into the ball cage or use a can of compressed air to dislodge dust and lint. 5. If the rollers inside the ball cage are dirty, clean the rollers with a cotton swab moistened lightly with isopropyl alcohol. 6. Recenter the rollers in their channels if they are misaligned. Ensure that fluff from the swab is not left on the rollers. 7. Replace the ball and retainer ring, and turn the retainer ring clockwise until it clicks into place.
Clean the outside casing of the mouse with a cloth moistened with a mild cleaning solution.
Mouse · Floppy Drive · CDs and DVDs

Clean your floppy drive using a commercially available cleaning kit. These kits contain pretreated floppy disks to remove contaminants that accumulate during normal operation.
If you notice problems, such as skipping, with the playback quality of your CDs or DVDs, try cleaning the discs.
For stubborn dirt, try using water or a diluted solution of water and mild soap. You can also purchase commercial products that clean discs and provide some protection from dust, fingerprints, and scratches. Cleaning products for CDs are also safe to use on DVDs.

About Your Desktop Computer
Front View

1 USB 2.0 connectors (2)
Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see System Setup for more information about booting to a USB device).
It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
2 LAN indicator light
This light indicates that a local area network (LAN) connection is established.
3 power button Press this button to turn on the computer.
4 Dell badge This badge can be rotated to match the orientation of your computer. To rotate, place fingers around the outside of the badge, press firmly, and turn the badge. You can also rotate the badge using the slot provided near the bottom of the badge.
5 power light The power light illuminates and blinks or remains solid to indicate different operating states:
l No light — The computer is turned off.
l Steady green — The computer is in a normal operating state.
l Blinking green — The computer is in a power-saving mode.
l Blinking or solid amber — See Power Problems.
To exit from a power-saving mode, press the power button or use the keyboard or the mouse if it is configured as a wake device in the Windows Device Manager. For more information about sleep modes and exiting from a power-saving mode, see Power Management.
See System Lights for a description of light codes that can help you troubleshoot problems with your computer.
Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see Diagnostic Lights.
7 hard-drive activity light
This light flickers when the hard drive is being accessed.
Use the headphone connector to attach headphones and most kinds of speakers.
Use the microphone connector to attach a microphone.

10 floppy drive Insert a floppy disk into this drive.
11 optical drive Insert media (if supported) into this drive.

1 card slots Access connectors for any installed PCI and PCI Express cards.
Plug serial, USB, and other devices into the appropriate connectors (see Back-Panel Connectors).
Insert the power cable.
4 voltage selection switch
Your computer is equipped with a manual voltage-selection switch.
To help avoid damaging a computer with a manual voltage selection switch, set the switch for the voltage that most closely matches the AC power available in your location.
Also, ensure that your monitor and attached devices are electrically rated to operate with the AC power available in your location.
5 padlock ring Insert a padlock to lock the computer cover.
6 cover release latch
Allows you to open the computer cover.

Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.
2 link integrity light
l Green — A good connection exists between a 10-Mbps network and
the computer.
l Orange — A good connection exists between a 100-Mbps network
and the computer.
l Yellow — A good connection exists between a 1-Gbps (or 1000-
Mbps) network and the computer.
l Off — The computer is not detecting a physical connection to the
network.
3 network To attach your computer to a network or broadband device, connect one
2 back-panel connectors · 3 power connector · 1 parallel connector

end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached.
On computers with a network connector card, use the connector on the card.
It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.
4 network activity light
Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.
Use the green line-out connector to attach headphones and most speakers with integrated amplifiers.
On computers with a sound card, use the connector on the card.
Use the line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR.
On computers with a sound card, use the connector on the card.
7 USB 2.0 connectors (5)
Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
Plug the cable from your VGA-compatible monitor into the blue connector.
Connect a serial device, such as a handheld device, to the serial port. The default designations are COM1 for serial connector 1 and COM2 for serial connector 2.
For more information, see System Setup Options.


1 drive release latch 2 optical drive 3 power supply
4 chassis intrusion switch (optional) 5 system board 6 card slots
7 heat sink assembly 8 front I/O panel


11 internal USB (USB1) 12 PCI Express x16 connector (SLOT1)



PCI, PCI Express Cards, and PS/2 Serial Port Adapters
Your Dell™ computer supports a PS/2 serial port adapter and provides the following connectors for PCI and PCI Express cards:
l Two low-profile PCI card slots
l One low-profile PCI Express x16 card slot

2. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 3. If you are installing a new card, remove the filler bracket to create a card-slot opening. Then continue with step 5. 4. If you are replacing a card that is already installed in the computer, remove the card (see Removing a PCI Card). If necessary, disconnect any cables connected to the card. Then continue with step 6. 5. Prepare the card for installation.

1 release tab 2 card retention latch 3 card
4 card-edge connector 5 card connector


1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 12. Install any drivers required for the card as described in the card documentation.


1 release tab 2 card retention latch 3 card
4 card-edge connector 5 card connector
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.
a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.


1 riser-card cage 2 handle

1 release tab 2 card retention latch 3 card
4 card-edge connector 5 card connector

a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position.

1 riser-card cage 2 slots 3 riser cards (2)
4 system board connectors (2)
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 18. Install any drivers required for the card as described in the card documentation.
a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.


1 riser-card cage 2 handle
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position.

1 riser-card cage 2 slots 3 riser cards (2)
4 system board connectors (2)

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.
Your computer supports one low-profile PCI Express x16 card. If your computer contains a riser-card cage, you can not install a PCI Express DVI card because the riser-card cage blocks the DVI-card (DVI_HDR) connector on the system board.
If you are replacing a PCI Express card with a different type of PCI Express card, remove the current driver for the card from the operating system. See the documentation that came with the card for information.
2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open. 3. If you are installing a new PCI Express x16 card or DVI-card, remove the filler bracket to create a card-slot opening. Then continue with step 5. 4. If you are replacing a PCI Express x16 card or DVI-card, remove the installed card (see Removing a PCI Express x16 Card or DVI-Card). If necessary, disconnect any cables connected to the card. Then continue with step 6. 5. Prepare the card for installation.

1 release tab 2 card retention latch 3 card
4 card-edge connector 5 card connector


1 PCI Express x16 or DVI card 2 PCI Express x16 card connector

1 PCI Express x16 card 2 DVI card connector 3 PCI Express x16 card connector
1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 13. Install any drivers required for the card as described in the card documentation.
If you are removing a PCI Express x16 card, go to step 5.
If you are removing a DVI card, go to step 6

1 PCI Express x16 card 2 lever 3 securing slot (not all cards)
4 securing tab 5 PCI Express x16 card connector


1 PCI Express x16 DVI-card 2 removal pull tab 3 DVI card connector
4 lever 5 securing slot 6 securing tab
7 PCI Express x16 card connector
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.
a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage up and gently pull on the handle and lift the riser-card cage up and away from the computer.


1 riser-card cage 2 handle
If you are replacing a card that is already installed in the computer, remove the card. If necessary, disconnect any cables connected to the card. Grasp the card by its corners, and ease it out of its connector.
1 release tab 2 card retention latch 3 card
4 card-edge connector 5 card connector


1 PCI Express x16 card 2 PCI Express x16 card connector
a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position.

1 riser-card cage 2 slots 3 riser cards (2)
4 system board connectors (2)
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 15. Install any drivers required for the card as described in the card documentation.

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.

1 riser-card cage 2 handle
1 PCI Express x16 card 2 lever 3 securing slot (not all cards)
4 securing tab 5 PCI Express x16 card connector
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.

a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position.

1 riser-card cage 2 slots 3 riser cards (2)
4 system board connectors (2)
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.

1 release tab 2 adapter retention latch 3 serial-port adapter bracket
4 serial port adapter connector
5 serial port adapter system board connector (PS2/SER2)
1. Follow the procedures in Before You Begin. 2. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 3. Disconnect the PS/2 serial-port cable from the system board (see System Board Components). 4. Grasp the PS/2 serial-port adapter bracket by its top corners, and ease it out of its connector. 5. If you are removing the adapter permanently, install a filler bracket in the empty card-slot opening.
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.

1 riser-card cage 2 handle 3 riser cards (2)
3. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 4. If you are installing a new serial port adapter, remove the filler bracket to create an empty card-slot opening. 5. If you are replacing an adapter that is already installed in the computer, remove the adapter. 6. If necessary, disconnect any cables connected to the adapter. 7. Grasp the serial port adapter by its top corners, and ease it out of its connector. 8. Prepare the serial port adapter for installation.
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position. 14. Connect any disconnected cables. 15. Replace the computer cover (see Replacing the Computer Cover).

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.

1 riser-card cage 2 handle 3 riser cards (2)
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position. 10. Replace the computer cover (see Replacing the Computer Cover). 11. Uninstall the adapter's driver. See the documentation that came with the adapter for instructions.

Processor
Lay the heat sink assembly down on its top, with the thermal grease facing upward.

1 heat sink assembly 2 captive screw housing (2)
Processor


1 processor 2 release lever 3 socket
Leave the release lever extended in the release position so that the socket is ready for the new processor, and go to Installing the Processor.


1 socket and processor pin-1 indicator 2 processor 3 release lever
a. Place the heat sink assembly back onto the heat-sink assembly bracket. b. Rotate the heat sink assembly down towards the computer base and ensure that the two captive screws are properly aligned with the holes in the system board. c. Tighten the two captive screws.

1 heat sink assembly 2 heat-sink assembly bracket 3 captive screw housing (2)
4 processor socket



Your computer supports:
l One SATA hard drive
l One optional floppy drive or media card reader or one second SATA hard drive
l One optional optical (CD or DVD) drive

1 optical drive 2 floppy drive or media card reader or SATA hard drive 3 hard drive
Connect the SATA hard drive to the connector labeled "SATA0." Connect the SATA CD or DVD drives to the connector labeled "SATA1" on the system board. Connect a second optional hard drive to the connector labeled "SATA2." See System Board Components for information about system board connectors.
When you install a drive, you connect two cables—a DC power cable and a data cable—to the back of the drive and to the system board.
1 interface cable connector 2 interface connector
Interface connectors are keyed for correct insertion.
Drives · Serial ATA Connector

Serial ATA Power Connector

1 power cable 2 power input connector
When connecting and disconnecting a SATA data cable, hold the cable by the black connector at each end.



1 drive release latch
Check the documentation that accompanied the drive to verify that the drive is configured for your computer.
a. Remove the inserts. b. Insert the three shoulder screws removed from the insert into the sides of the new drive and tighten them. c. Lift the drive release latch up and insert the new optical device. 4. If you are replacing an existing drive:
a. Follow procedures in Removing an Optical Drive to remove the existing drive. b. Remove the three shoulder screws from the existing drive. c. Insert the three shoulder screws into the sides of the new drive and tighten them.


2 optical drive


1 drive release latch 2 floppy drive
a. Use a small flat-edge screw driver on the back side of the drive-panel insert to gently pop off the insert. b. Remove the four shoulder screws from the drive-panel insert. 2. If you are replacing an existing drive:
Remove the four shoulder screws from the existing drive.



1 floppy drive 2 slot verification number


1 media card reader 2 drive release latch 3 media card reader cable
a. Use a small flat-edge screw driver on the back side of the drive-panel insert to gently pop off the insert. b. Remove the four shoulder screws from the drive-panel insert. 2. If you are replacing an existing media card reader:
Remove the four shoulder screws from the existing media card reader.



1 media card reader 2 shoulder screws (4) 3 media card reader cable
4 shoulder screw slots (2)
3. Remove the optical drive (see Removing an Optical Drive) from the bay and carefully set it aside. 4. Remove the floppy drive, media card reader, or second hard drive, if installed, (see Removing a Floppy Drive, Removing the Media Card Reader, or Removing and Replacing a Second Hard Drive) and carefully set it aside. 5. Squeeze the two plastic securing clips on each side of the hard drive and slide the drive towards the back of the computer.


1 securing clips (2) 2 hard drive

1 hard drive 2 release tabs (2) 3 plastic hard-drive bracket

1 securing tabs (2) 2 drive 3 release tabs (2)
4 plastic hard-drive bracket


1 hard drive 2 slot verification number
6. Replace the floppy drive, media card reader, or second hard drive (see Installing a Floppy Drive, Installing the Media Card Reader, or Removing and Replacing a Second Hard Drive). 7. Replace the optical drive (see Installing an Optical Drive). 8. Check all connectors to be certain that they are properly cabled and firmly seated. 9. Replace the computer cover (see Replacing the Computer Cover). 10. If the drive you just installed is the primary drive, insert a bootable medium into your boot drive. 11. Turn on the computer. 12. Enter system setup and update the appropriate Primary Drive option (0 or 2) (see Entering System Setup). 13. Exit system setup, and reboot the computer. 14. Partition and logically format your drive before you proceed to the next step.
For instructions, see the documentation that came with your operating system.
For instructions, see the documentation that came with your operating system.
For information on RAID configuration, see About RAID Configurations

a. Pull up on the drive release latch and slide the hard drive towards the back of the computer. b. Disconnect the data and power cables from the back of the drive. c. Then, lift up to remove the drive from the computer. 6. To replace the second hard drive:
a. Align the shoulder screws with the screw guides, and slide the drive into the bay until it clicks into place. b. Connect the power and data cables to the back of the drive.


1 data cable 2 hard drive system board connector


Desktop Computer
About Your Computer Finding Information Desktop Computer Desktop Computer (Model # DCNE) Specifications Advanced Features Cleaning Your Computer Reinstalling Drivers and the Operating System Solving Problems Microsoft® Windows® XP and Windows Vista® Features Troubleshooting Tools and Utilities Getting Help Warranty FCC Regulatory Model (U.S. Only) Glossary
Removing and Replacing Parts Before You Begin Removing the Computer Cover Chassis Intrusion Switch I/O Panel Drives PCI, PCI Express Cards, and PS/2 Serial Port Adapters Power Supply Processor Battery Replacing the System Board Memory Replacing the Computer Cover
Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, OptiPlex, Inspiron, Dimension, Latitude, Dell Precision, DellNet, TravelLite, Dell OpenManage, PowerVault, Axim, PowerEdge, PowerConnect, and PowerApp are trademarks of Dell Inc.; AMD, AMD Athlon, AMD Phenom, and combinations thereof, and Cool 'n' Quiet are trademarks of Advanced Micro Devices, Inc; Microsoft and Windows are registered trademarks of Microsoft Corporation; IBM is a registered trademark of International Business Machines Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
March 2008 RP699 Rev. A03

Removing the I/O Panel

1 securing screw 2 I/O panel 3 I/O cable connector
4 I/O connector pull loop
I/O Panel

Replacing the Power Supply

1 power supply 2 release button 3 screws (2)
4 AC power connector
Power Supply





*Use 22-AWG wire instead of 18-AWG wire.







Removing the Computer Cover

1 security cable slot 2 cover release latch 3 padlock ring

Desktop Computer (Model # DCNE) Specifications
Microprocessor type AMD Phenom™ processors
AMD Athlon™ 64 X2 Dual-Core processor
AMD Athlon 64 X2:1-MB L2 dedicated cache
Type 533-, 667-, or 800-MHz DDR2 SDRAM
Memory modules supported 256 MB, 512 MB, 1 GB, or 2 GB non-ECC
Maximum memory 8 GB
Chipset nVidia GeForce 6150LE/Nforce 430
RAID support RAID 0 and RAID 1
Data bus width 64 bits
Address bus width 40 bits
BIOS chip (NVRAM) 8 Mb or 4 Mb

NIC integrated network interface with ASF 1.03 and 2.0 support as defined by DMTF
Capable of 10/100/1000 communication
Type nVidia integrated video (DirectX 9.0c Shader Model 3.0 Graphics Processing Unit) or PCI Express x16 graphics card or DVI graphics card
Type Sigma Tel 9200 CODEC (2.1 Channel Audio)
Stereo conversion 24-bit analog-to-digital; 24-bit digital-to-analog
Drives SATA controller supporting two 3.5-inch devices (two 3.5-inch hard drives supported)
Bus type PCI 2.3 PCI Express 1.0A SATA 1.0A and 2.0 USB 2.0
Bus speed PCI: 133 MB/s PCI Express x16: 40 GB/s bidirectional speed SATA: 1.5 Gbps and 3.0 Gbps USB: 480 Mbps high speed, 12Mbps full speed, 1.2 Mbps low speed
Cards half-length, full-height cards supported with optional riser-card cage
card size low profile
connector size 124 pins
card size low profile
power 25 W maximum
connector size 164 pins (x16)
connector data width (maximum) 16 PCI Express lanes (x16)
Externally accessible one 3.5-inch drive one bay for optical drive or optional second hard drive, supporting up to two 3.5-inch hard drives
Internally accessible one bay for a 1-inch-high hard drive
External connectors:
Serial 9-pin connector; 16550C-compatible
Parallel 25-hole connector (bidirectional)
Video 15-hole VGA connector
Network adapter RJ45 connector

Optional PS/2 with secondary serial port adapter
Optional DVI 36-pin connector
USB two front-panel and five back-panel USB 2.0– compliant connectors
Audio two connectors for line-in and line-out; two front- panel connectors for headphones and microphone
System board connectors:
SATA three 7-pin connectors
Floppy drive 38-pin connector
Serial 24-pin connector for optional second serial port card
PCI 2.3 two 124-pin connectors
Internal USB 10-pin connector
Intrusion switch 3-pin connector
Memory modules four 240-pin connector
Power 12V 4-pin connector
Front panel 40-pin connector
in Microsoft® Windows® XP and Windows Vista®, brings up the Windows Security window; in MS-DOS® mode, restarts (reboots) the computer
or starts embedded system setup (during system start- up only)
starts the RAID setup menu if RAID is turned on in the system setup program
or displays a boot device menu that allows the user to enter a device for a single boot (during system start- up only) as well as options to run hard-drive and system diagnostics
Power control front panel — push button
Power light green light. Blinking green indicates a sleep mode; solid green indicates a power-on state.
amber light. Blinking amber indicates a problem with an installed device; solid amber indicates an internal power problem (see Power Problems).
Hard-drive access light front panel — green
Link light front panel — solid green light indicates network connection
Link integrity light (on integrated network adapter) rear panel — green light for 10-Mb operation; orange light for 100-Mb operation; yellow light for a 1000-Mb (1-Gb) operation
Activity light (on integrated network adapter) rear panel — yellow blinking light
Diagnostic lights front panel — Four lights on the front panel. See Diagnostic Lights.
Standby power light AUX_PWR on the system board
DC power supply:


Voltage manual selection power supplies — 90 to 135 V at 50/60 Hz; 180 to 265 V at 50/60 Hz
Operating 0.25 G at 3 to 200 Hz at 0.5 octave/min
Storage 0.5 G at 3 to 200 Hz at 1 octave/min
Operating bottom half-sine pulse with a change in velocity of 50.8 cm/sec (20 inches/sec)
Storage 27-G faired square wave with a velocity change of 508 cm/sec (200 inches/sec)
Operating –15.2 to 3048 m (–50 to 10,000 ft)
Storage –15.2 to 10,668 m (–50 to 35,000 ft)
Airborne contaminant level G2 or lower as defined by ISA-S71.04-1985

Speaker
Installing a Speaker
Speaker

The following information is provided on the device or devices covered in this document in compliance with the FCC regulations:
l Company name:
Dell Inc. Worldwide Regulatory Compliance & Environmental Affairs One Dell Way Round Rock, TX 78682 USA 512-338-4400

What Are You Looking For?
l A diagnostic program for my computer
l Drivers for my computer
l My device documentation
l Desktop System Software (DSS)
Documentation and drivers are already installed on your computer. You can use the Drivers and Utilities media to reinstall drivers (see Reinstalling Drivers and Utilities) or to run the Dell Diagnostics (see Dell Diagnostics).

Readme files may be included on your media to provide last-minute updates about technical changes to your computer or advanced technical-reference material for technicians or experienced users.
l How to set up my computer
l Basic troubleshooting information
l How to run the Dell Diagnostics
l Error codes and diagnostic lights
l Tools and utilities
l Additional information about setting up my computer
l How to troubleshoot and solve problems
l How to remove and install parts

l Terms and Conditions (U.S. only)

l End User License Agreement
l Service Tag and Express Service Code
l Microsoft Windows License Label

located on your computer.
Your computer's Service Tag contains both a Service Tag number and an Express Service Code.
l Use the Service Tag to identify your computer when you use
support.dell.com or contact support.
l Enter the Express Service Code to direct your call when contacting support.
Use the product key on the Microsoft Windows License Label if you need to reinstall your operating system.

l Use the product key on the License Label if you need to reinstall your
operating system.
l Solutions — Troubleshooting hints and tips, articles from
technicians, online courses, and frequently asked questions
l Community — Online discussion with other Dell customers
l Upgrades — Upgrade information for components, such as
memory, the hard drive, and the operating system
l Customer Care — Contact information, service call and order
status, warranty, and repair information
l Service and support — Service call status and support history,
service contract, online discussions with technical support
l Dell Technical Update Service — Proactive e-mail notification of
software and hardware updates for your computer
l Reference — Computer documentation, details on my computer
configuration, product specifications, and white papers
l Downloads — Certified drivers, patches, and software updates
l Desktop System Software (DSS)— If you reinstall the operating
system for your computer, you should also reinstall the DSS utility. DSS provides critical updates for your operating system and support for Dell™ 3.5-inch USB floppy drives, AMD™ processors, optical drives, and USB devices. DSS is necessary for correct operation of your Dell computer. The software automatically detects your computer and operating system and installs the updates appropriate for your configuration.
To download Desktop System Software:

l Software upgrades and troubleshooting hints — Frequently asked
questions, hot topics, and general health of your computing environment
Dell Support 3 is an automated upgrade and notification system installed on your computer. This support provides real-time health scans of your computing environment, software updates, and relevant self-support information. Access Dell
Support 3 from the icon in the taskbar.
l How to find information about my computer and its components
l How to connect to the Internet
l How to add user accounts for different people
l How to transfer files and settings from another computer
The Windows Welcome Center automatically appears when you use the computer for the first time. You can choose to have it appear every time you start your computer by placing a check in the Run at startup checkbox. Another method of
accessing the Welcome Center is to click the Windows Vista Start button , and then click Welcome Center.
l How to use Microsoft Windows XP or Windows Vista®
l How to work with programs and files
l How to personalize my desktop
Microsoft Windows XP:
Microsoft Windows Vista:
l Remote help with troubleshooting my computer DellConnect™ Service and Support
Dell associates can diagnose and repair your computer remotely over a broadband connection. To learn more and get started with DellConnect, go to support.dell.com and click Revolutionary remote help—DellConnect.
l How to reinstall my operating system Operating System Media
The operating system is already installed on your computer. To reinstall your operating system, use the Operating System media. See Reinstalling Microsoft® Windows Vista® and Windows® XP.
After you reinstall your operating system, use the optional Drivers and Utilities media to reinstall drivers for the devices that came with your computer.

Your operating system product key label is located on your computer.

Problems With Your Order
Returning Items for Warranty Repair or Credit
When prompted by Dell's automated telephone system, enter your Express Service Code to route the call directly to the proper support personnel. If you do not have an Express Service Code, open the Dell Accessories folder, double-click the Express Service Code icon, and follow the directions.
For instructions on using the support service, see Support Service.
You can access Dell Support at support.dell.com. Select your region on the WELCOME TO DELL SUPPORT page, and fill in the requested details to access help tools and information.
You can contact Dell electronically using the following addresses:
l World Wide Web
www.dell.com/ap/ (Asian/Pacific countries only)
www.dell.com/jp (Japan only)
www.euro.dell.com (Europe only)
www.dell.com/la/ (Latin American and Caribbean countries)
www.dell.ca (Canada only)
l Anonymous file transfer protocol (FTP)
ftp.dell.com/
Log in as user: anonymous, and use your e-mail address as your password.
l Electronic Support Service
mobile_support@us.dell.com
support@us.dell.com

la-techsupport@dell.com (Latin America and Caribbean countries only)
apsupport@dell.com (Asian/Pacific countries only)
support.jp.dell.com (Japan only)
support.euro.dell.com (Europe only)
l Electronic Quote Service
apmarketing@dell.com (Asian/Pacific countries only)
sales_canada@dell.com (Canada only)
Dell's automated support service—AutoTech—provides recorded answers to the questions most frequently asked by Dell customers about their portable and desktop computers.
When you call AutoTech, use your touch-tone telephone to select the subjects that correspond to your questions.
The AutoTech service is available 24 hours a day, 7 days a week. You can also access this service through the support service. For the telephone number to call for your region, see Contacting Dell.
To check on the status of any Dell™ products that you have ordered, you can go to support.dell.com, or you can call the automated order-status service. A recording prompts you for the information needed to locate and report on your order. For the telephone number to call for your region, see Contacting Dell.
Dell's support service is available 24 hours a day, 7 days a week, to answer your questions about Dell hardware. Our support staff uses computer-based diagnostics to provide fast, accurate answers.
To contact Dell's support service, see Obtaining Assistance and then call the number for your country as listed in Contacting Dell.
If you have a problem with your order, such as missing parts, wrong parts, or incorrect billing, contact Dell for customer assistance. Have your invoice or packing slip handy when you call. For the telephone number to call for your region, see Contacting Dell.
If you need information about additional products available from Dell, or if you would like to place an order, visit the Dell website at www.dell.com. For the telephone number to call for your region or to speak to a sales specialist, see Contacting Dell.
Prepare all items being returned, whether for repair or credit, as follows:
For the telephone number to call for your region, see Contacting Dell.
2. Include a copy of the invoice and a letter describing the reason for the return. 3. Include a copy of the Diagnostics Checklist (see Diagnostics Checklist), indicating the tests that you have run and any error messages reported by the Dell Diagnostics (see Dell Diagnostics). 4. Include any accessories that belong with the item(s) being returned (power cables, software floppy disks, guides, and so on) if the return is for credit. 5. Pack the equipment to be returned in the original (or equivalent) packing materials.
You are responsible for paying shipping expenses. You are also responsible for insuring any product returned, and you assume the risk of loss during shipment to Dell. Collect On Delivery (C.O.D.) packages are not accepted.

Returns that are missing any of the preceding requirements will be refused at Dell's receiving dock and returned to you.
Remember to fill out the Diagnostics Checklist (see Diagnostics Checklist). If possible, turn on your computer before you call Dell for assistance and call from a telephone at or near the computer. You may be asked to type some commands at the keyboard, relay detailed information during operations, or try other troubleshooting steps possible only at the computer itself. Ensure that the computer documentation is available.
Name:
Date:
Address:
Phone number:
Service Tag (bar code on the back or bottom of the computer):
Express Service Code:
Return Material Authorization Number (if provided by Dell support technician):
Operating system and version:
Devices:
Expansion cards:
Are you connected to a network? Yes No
Network, version, and network adapter:
Programs and versions:
See your operating system documentation to determine the contents of the system's start-up files. If the computer is connected to a printer, print each file. Otherwise, record the contents of each file before calling Dell.
Error message, beep code, or diagnostic code:
Description of problem and troubleshooting procedures you performed:
For customers in the United States, call 800-WWW-DELL (800-999-3355).
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
Diagnostics Checklist

Terms in this Glossary are provided for informational purposes only and may or may not describe features included with your particular computer.
AC — alternating current — The form of electricity that powers your computer when you plug the AC adapter power cable in to an electrical outlet.
ACPI — advanced configuration and power interface — A power management specification that enables Microsoft® Windows® operating systems to put a computer in standby or hibernate mode to conserve the amount of electrical power allocated to each device attached to the computer.
AGP — accelerated graphics port — A dedicated graphics port that allows system memory to be used for video-related tasks. AGP delivers a smooth, true-color video image because of the faster interface between the video circuitry and the computer memory.
AHCI — Advanced Host Controller Interface — An interface for a SATA hard drive Host Controller which allows the storage driver to enable technologies such as Native Command Queuing (NCQ) and hot plug.
ALS — ambient light sensor — A feature that helps to control display brightness.
antivirus software — A program designed to identify, quarantine, and/or delete viruses from your computer.
ASF — alert standards format — A standard to define a mechanism for reporting hardware and software alerts to a management console. ASF is designed to be platform- and operating system-independent.
battery life span — The length of time (years) during which a portable computer battery is able to be depleted and recharged.
battery operating time — The length of time (minutes or hours) that a portable computer battery powers the computer.
BIOS — basic input/output system — A program (or utility) that serves as an interface between the computer hardware and the operating system. Unless you understand what effect these settings have on the computer, do not change them. Also referred to as system setup.
bit — The smallest unit of data interpreted by your computer.
Bluetooth® wireless technology — A wireless technology standard for short-range (9 m [29 feet]) networking devices that allows for enabled devices to automatically recognize each other.
boot sequence — Specifies the order of the devices from which the computer attempts to boot.
bootable media — A disk that you can use to start your computer. In case your hard drive is damaged or your computer has a virus, ensure that you always have a bootable DVD, CD, or floppy disk available. Your Drivers and Utilities media.
bps — bits per second — The standard unit for measuring data transmission speed.
BTU — British thermal unit — A measurement of heat output.
bus — A communication pathway between the components in your computer.
bus speed — The speed, given in MHz, that indicates how fast a bus can transfer information.
byte — The basic data unit used by your computer. A byte is usually equal to 8 bits.
C — Celsius — A temperature measurement scale where 0° is the freezing point and 100° is the boiling point of water.
cache — A special high-speed storage mechanism which can be either a reserved section of main memory or an independent high-speed storage device. The cache enhances the efficiency of many processor operations.
L1 cache — Primary cache stored inside the processor.
L2 cache — Secondary cache which can either be external to the processor or incorporated into the processor architecture.
carnet — An international customs document that facilitates temporary imports into foreign countries. Also known as a merchandise passport.
CD-R — CD recordable — A recordable version of a CD. Data can be recorded only once onto a CD-R. Once recorded, the data cannot be erased or written over.
CD-RW — CD rewritable — A rewritable version of a CD. Data can be written to a CD-RW disc, and then erased and written over (rewritten).
CD-RW drive — A drive that can read CDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs. You can write to CD-RW discs multiple times,

but you can write to CD-R discs only once.
CD-RW/DVD drive — A drive, sometimes referred to as a combo drive, that can read CDs and DVDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs. You can write to CD-RW discs multiple times, but you can write to CD-R discs only once.
clock speed — The speed, given in MHz, that indicates how fast computer components that are connected to the system bus operate.
COA — Certificate of Authenticity — The Windows alpha-numeric code located on a sticker on your computer. Also referred to as the Product Key or Product ID.
Control Panel — A Windows utility that allows you to modify operating system and hardware settings, such as display settings.
controller — A chip that controls the transfer of data between the processor and memory or between the processor and devices.
CRIMM — continuity rambus in-line memory module — A special module that has no memory chips and is used to fill unused RIMM slots.
cursor — The marker on a display or screen that shows where the next keyboard, touch pad, or mouse action will occur. It often is a blinking solid line, an underline character, or a small arrow.
DDR SDRAM — double-data-rate SDRAM — A type of SDRAM that doubles the data burst cycle, improving system performance.
DDR2 SDRAM — double-data-rate 2 SDRAM — A type of DDR SDRAM that uses a 4-bit prefetch and other architectural changes to boost memory speed to over 400 MHz.
device — Hardware such as a disk drive, printer, or keyboard that is installed in or connected to your computer.
device driver — See driver.
DIMM — dual in-line memory module — A circuit board with memory chips that connects to a memory module on the system board.
DIN connector — A round, six-pin connector that conforms to DIN (Deutsche Industrie-Norm) standards; it is typically used to connect PS/2 keyboard or mouse cable connectors.
disk striping — A technique for spreading data over multiple disk drives. Disk striping can speed up operations that retrieve data from disk storage. Computers that use disk striping generally allow the user to select the data unit size or stripe width.
DMA — direct memory access — A channel that allows certain types of data transfer between RAM and a device to bypass the processor.
docking device — See APR.
DMTF — Distributed Management Task Force — A consortium of hardware and software companies who develop management standards for distributed desktop, network, enterprise, and Internet environments.
domain — A group of computers, programs, and devices on a network that are administered as a unit with common rules and procedures for use by a specific group of users. A user logs on to the domain to gain access to the resources.
DRAM — dynamic random-access memory — Memory that stores information in integrated circuits containing capacitors.
driver — Software that allows the operating system to control a device such as a printer. Many devices do not work properly if the correct driver is not installed in the computer.
DSL — Digital Subscriber Line — A technology that provides a constant, high-speed Internet connection through an analog telephone line.
dual-core — A technology in which two physical computational units exist inside a single processor package, thereby increasing computing efficiency and multi- tasking ability.
dual display mode — A display setting that allows you to use a second monitor as an extension of your display. Also referred to as extended display mode.
DVD-R — DVD recordable — A recordable version of a DVD. Data can be recorded only once onto a DVD-R. Once recorded, the data cannot be erased or written over.
DVD+RW — DVD rewritable — A rewritable version of a DVD. Data can be written to a DVD+RW disc, and then erased and written over (rewritten). (DVD+RW technology is different from DVD-RW technology.)
DVD+RW drive — drive that can read DVDs and most CD media and write to DVD+RW (rewritable DVDs) discs.
DVI — digital video interface — A standard for digital transmission between a computer and a digital video display.
ECC — error checking and correction — A type of memory that includes special circuitry for testing the accuracy of data as it passes in and out of memory.
ECP — extended capabilities port — A parallel connector design that provides improved bidirectional data transmission. Similar to EPP, ECP uses direct memory access to transfer data and often improves performance.
EIDE — enhanced integrated device electronics — An improved version of the IDE interface for hard drives and CD drives.
EMI — electromagnetic interference — Electrical interference caused by electromagnetic radiation.

ENERGY STAR® — Environmental Protection Agency requirements that decrease the overall consumption of electricity.
EPP — enhanced parallel port — A parallel connector design that provides bidirectional data transmission.
ESD — electrostatic discharge — A rapid discharge of static electricity. ESD can damage integrated circuits found in computer and communications equipment.
expansion card — A circuit board that installs in an expansion slot on the system board in some computers, expanding the capabilities of the computer. Examples include video, modem, and sound cards.
expansion slot — A connector on the system board (in some computers) where you insert an expansion card, connecting it to the system bus.
ExpressCard — A removable I/O card adhering to the PCMCIA standard. Modems and network adapters are common types of ExpressCards. ExpressCards support both the PCI Express and USB 2.0 standard.
Express Service Code — A numeric code located on a sticker on your Dell™ computer. Use the Express Service Code when contacting Dell for assistance. Express Service Code service may not be available in some countries.
extended display mode — A display setting that allows you to use a second monitor as an extension of your display. Also referred to as dual display mode.
extended PC Card — A PC Card that extends beyond the edge of the PC Card slot when installed.
Fahrenheit — A temperature measurement scale where 32° is the freezing point and 212° is the boiling point of water.
FBD — fully-buffered DIMM — A DIMM with DDR2 DRAM chips and an Advanced Memory Buffer (AMB) that speeds communication between the DDR2 SDRAM chips and the system.
FCC — Federal Communications Commission — A U.S. agency responsible for enforcing communications-related regulations that state how much radiation computers and other electronic equipment can emit.
fingerprint reader — A strip sensor that uses your unique fingerprint to authenticate your user identity to help secure your computer.
folder — A term used to describe space on a disk or drive where files are organized and grouped. Files in a folder can be viewed and ordered in various ways, such as alphabetically, by date, and by size.
format — The process that prepares a drive or disk for file storage. When a drive or disk is formatted, the existing information on it is lost.
FSB — front side bus — The data path and physical interface between the processor and RAM.
FTP — file transfer protocol — A standard Internet protocol used to exchange files between computers connected to the Internet.
G — gravity — A measurement of weight and force.
GB — gigabyte — A measurement of data storage that equals 1024 MB (1,073,741,824 bytes). When used to refer to hard drive storage, the term is often rounded to 1,000,000,000 bytes.
GHz — gigahertz — A measurement of frequency that equals one thousand million Hz, or one thousand MHz. The speeds for computer processors, buses, and interfaces are often measured in GHz.
graphics mode — A video mode that can be defined as x horizontal pixels by y vertical pixels by z colors. Graphics modes can display an unlimited variety of shapes and fonts.
GUI — graphical user interface — Software that interacts with the user by means of menus, windows, and icons. Most programs that operate on the Windows operating systems are GUIs.
hard drive — A drive that reads and writes data on a hard disk. The terms hard drive and hard disk are often used interchangeably.
heat sink — A metal plate on some processors that helps dissipate heat.
hibernate mode — A power management mode that saves everything in memory to a reserved space on the hard drive and then turns off the computer. When you restart the computer, the memory information that was saved to the hard drive is automatically restored.
HTTP — hypertext transfer protocol — A protocol for exchanging files between computers connected to the Internet.
HyperTransport — HyperTransport is an AMD™ technology that can increase overall computer performance by removing bottlenecks, increasing system bandwidth, and reducing system latency.
Hz — hertz — A unit of frequency measurement that equals 1 cycle per second. Computers and electronic devices are often measured in kilohertz (kHz), megahertz (MHz), gigahertz (GHz), or terahertz (THz).

IC — integrated circuit — A semiconductor wafer, or chip, on which thousands or millions of tiny electronic components are fabricated for use in computer, audio, and video equipment.
IDE — integrated device electronics — An interface for mass storage devices in which the controller is integrated into the hard drive or CD drive.
IEEE 1394 — Institute of Electrical and Electronics Engineers, Inc. — A high-performance serial bus used to connect IEEE 1394-compatible devices, such as digital cameras and DVD players, to the computer.
infrared sensor — A port that allows you to transfer data between the computer and infrared-compatible devices without using a cable connection.
integrated — Usually refers to components that are physically located on the computer's system board. Also referred to as built-in.
I/O — input/output — An operation or device that enters and extracts data from your computer. Keyboards and printers are I/O devices.
I/O address — An address in RAM that is associated with a specific device (such as a serial connector, parallel connector, or expansion slot) and allows the processor to communicate with that device.
IrDA — Infrared Data Association — The organization that creates international standards for infrared communications.
IRQ — interrupt request — An electronic pathway assigned to a specific device so that the device can communicate with the processor. Each device connection must be assigned an IRQ. Although two devices can share the same IRQ assignment, you cannot operate both devices simultaneously.
ISP — Internet service provider — A company that allows you to access its host server to connect directly to the Internet, send and receive e-mail, and access websites. The ISP typically provides you with a software package, user name, and access phone numbers for a fee.
Kb — kilobit — A unit of data that equals 1024 bits. A measurement of the capacity of memory integrated circuits.
KB — kilobyte — A unit of data that equals 1024 bytes but is often referred to as 1000 bytes.
key combination — A command requiring you to press multiple keys at the same time.
kHz — kilohertz — A measurement of frequency that equals 1000 Hz.
LAN — local area network — A computer network covering a small area. A LAN usually is confined to a building or a few nearby buildings. A LAN can be connected to another LAN over any distance through telephone lines and radio waves to form a wide area network (WAN).
LCD — liquid crystal display — The technology used by portable computer and flat-panel displays.
LED — light-emitting diode — An electronic component that emits light to indicate the status of the computer.
local bus — A data bus that provides a fast throughput for devices to the processor.
LPT — line print terminal — The designation for a parallel connection to a printer or other parallel device.
Mb — megabit — A measurement of memory chip capacity that equals 1024 Kb.
Mbps — megabits per second — One million bits per second. This measurement is typically used for transmission speeds for networks and modems.
MB — megabyte — A measurement of data storage that equals 1,048,576 bytes. 1 MB equals 1024 KB. When used to refer to hard drive storage, the term is often rounded to 1,000,000 bytes.
MB/sec — megabytes per second — One million bytes per second. This measurement is typically used for data transfer ratings.
media bay — A bay that supports devices such as optical drives, a second battery, or a Dell TravelLite™ module.
memory — A temporary data storage area inside your computer. Because the data in memory is not permanent, it is recommended that you frequently save your files while you are working on them, and always save your files before you shut down the computer. Your computer can contain several different forms of memory, such as RAM, ROM, and video memory. Frequently, the word memory is used as a synonym for RAM.
memory address — A specific location where data is temporarily stored in RAM.
memory mapping — The process by which the computer assigns memory addresses to physical locations at start-up. Devices and software can then identify information that the processor can access.
memory module — A small circuit board containing memory chips, which connects to the system board.
MHz — megahertz — A measure of frequency that equals 1 million cycles per second. The speeds for computer processors, buses, and interfaces are often measured in MHz.

Mini PCI — A standard for integrated peripheral devices with an emphasis on communications such as modems and NICs. A Mini PCI card is a small external card that is functionally equivalent to a standard PCI expansion card.
Mini-Card — A small card designed for integrated peripherals, such as communication NICs. The Mini-Card is functionally equivalent to a standard PCI expansion card.
modem — A device that allows your computer to communicate with other computers over analog telephone lines. Three types of modems include: external, PC Card, and internal. You typically use your modem to connect to the Internet and exchange e-mail.
module bay — See media bay.
MP — megapixel — A measure of image resolution used for digital cameras.
ms — millisecond — A measure of time that equals one thousandth of a second. Access times of storage devices are often measured in ms.
network adapter — A chip that provides network capabilities. A computer may include a network adapter on its system board, or it may contain a PC Card with an adapter on it. A network adapter is also referred to as a NIC (network interface controller).
NIC — See network adapter.
notification area — The section of the Windows taskbar that contains icons for providing quick access to programs and computer functions, such as the clock, volume control, and print status. Also referred to as system tray.
ns — nanosecond — A measure of time that equals one billionth of a second.
NVRAM — nonvolatile random access memory — A type of memory that stores data when the computer is turned off or loses its external power source. NVRAM is used for maintaining computer configuration information such as date, time, and other system setup options that you can set.
optical drive — A drive that uses optical technology to read or write data from CDs, DVDs, or DVD+RWs. Example of optical drives include CD drives, DVD drives, CD-RW drives, and CD-RW/DVD combo drives.
parallel connector — An I/O port often used to connect a parallel printer to your computer. Also referred to as an LPT port.
partition — A physical storage area on a hard drive that is assigned to one or more logical storage areas known as logical drives. Each partition can contain multiple logical drives.
PC Card — A removable I/O card adhering to the PCMCIA standard. Modems and network adapters are common types of PC Cards.
PCI — peripheral component interconnect — PCI is a local bus that supports 32-and 64-bit data paths, providing a high-speed data path between the processor and devices such as video, drives, and networks.
PCI Express — A modification to the PCI interface that boosts the data transfer rate between the processor and the devices attached to it. PCI Express can transfer data at speeds from 250 MB/sec to 4 GB/sec. If the PCI Express chip set and the device are capable of different speeds, they will operate at the slower speed.
PCMCIA — Personal Computer Memory Card International Association — The organization that establishes standards for PC Cards.
PIO — programmed input/output — A method of transferring data between two devices through the processor as part of the data path.
pixel — A single point on a display screen. Pixels are arranged in rows and columns to create an image. A video resolution, such as 800 x 600, is expressed as the number of pixels across by the number of pixels up and down.
Plug-and-Play — The ability of the computer to automatically configure devices. Plug and Play provides automatic installation, configuration, and compatibility with existing hardware if the BIOS, operating system, and all devices are Plug and Play compliant.
POST — power-on self-test — Diagnostics programs, loaded automatically by the BIOS, that perform basic tests on the major computer components, such as memory, hard drives, and video. If no problems are detected during POST, the computer continues the start-up.
processor — A computer chip that interprets and executes program instructions. Sometimes the processor is referred to as the CPU (central processing unit).
PS/2 — personal system/2 — A type of connector for attaching a PS/2-compatible keyboard, mouse, or keypad.
PXE — pre-boot execution environment — A WfM (Wired for Management) standard that allows networked computers that do not have an operating system to be configured and started remotely.
RAID — redundant array of independent disks — A method of providing data redundancy. Some common implementations of RAID include RAID 0, RAID 1, RAID 5, RAID 10, and RAID 50.

RAM — random-access memory — The primary temporary storage area for program instructions and data. Any information stored in RAM is lost when you shut down your computer.
readme file — A text file included with a software package or hardware product. Typically, readme files provide installation information and describe new product enhancements or corrections that have not yet been documented.
read-only — Data and/or files you can view but cannot edit or delete. A file can have read-only status if:
¡ It resides on a physically write-protected floppy disk, CD, or DVD.
¡ It is located on a network in a directory and the system administrator has assigned rights only to specific individuals.
refresh rate — The frequency, measured in Hz, at which your screen's horizontal lines are recharged (sometimes also referred to as its vertical frequency). The higher the refresh rate, the less video flicker can be seen by the human eye.
resolution — The sharpness and clarity of an image produced by a printer or displayed on a monitor. The higher the resolution, the sharper the image.
RFI — radio frequency interference — Interference that is generated at typical radio frequencies, in the range of 10 kHz to 100,000 MHz. Radio frequencies are at the lower end of the electromagnetic frequency spectrum and are more likely to have interference than the higher frequency radiations, such as infrared and light.
ROM — read-only memory — Memory that stores data and programs that cannot be deleted or written to by the computer. ROM, unlike RAM, retains its contents after you shut down your computer. Some programs essential to the operation of your computer reside in ROM.
RPM — revolutions per minute — The number of rotations that occur per minute. Hard drive speed is often measured in rpm.
RTC — real time clock — Battery-powered clock on the system board that keeps the date and time after you shut down the computer.
RTCRST — real-time clock reset — A jumper on the system board of some computers that can often be used for troubleshooting problems.
SAS — serial attached SCSI — A faster, serial version of the SCSI interface (as opposed to the original SCSI parallel architecture).
SATA — serial ATA — A faster, serial version of the ATA (IDE) interface.
ScanDisk — A Microsoft utility that checks files, folders, and the hard disk's surface for errors. ScanDisk often runs when you restart the computer after it has stopped responding.
SCSI — small computer system interface — A high-speed interface used to connect devices to a computer, such as hard drives, CD drives, printers, and scanners. The SCSI can connect many devices using a single controller. Each device is accessed by an individual identification number on the SCSI controller bus.
SDRAM — synchronous dynamic random-access memory — A type of DRAM that is synchronized with the optimal clock speed of the processor.
serial connector — An I/O port often used to connect devices such as a handheld digital device or digital camera to your computer.
Service Tag — A bar code label on your computer that identifies your computer when you access Dell Support at support.dell.com or when you call Dell for customer service or technical support.
setup program — A program that is used to install and configure hardware and software. The setup.exe or install.exe program comes with most Windows software packages. Setup program differs from system setup.
shortcut — An icon that provides quick access to frequently used programs, files, folders, and drives. When you place a shortcut on your Windows desktop and double-click the icon, you can open its corresponding folder or file without having to find it first. Shortcut icons do not change the location of files. If you delete a shortcut, the original file is not affected. Also, you can rename a shortcut icon.
SIM — Subscriber Identity Module — A SIM card contains a microchip that encrypts voice and data transmissions. SIM cards can be used in phones or portable computers.
smart card — A card that is embedded with a processor and a memory chip. Smart cards can be used to authenticate a user on computers equipped for smart cards.
S/PDIF — Sony/Philips Digital Interface — An audio transfer file format that allows the transfer of audio from one file to another without converting it to and from an analog format, which could degrade the quality of the file.
standby mode — A power management mode that shuts down all unnecessary computer operations to save energy.
Strike Zone™ — Reinforced area of the platform base that protects the hard drive by acting as a dampening device when a computer experiences resonating shock or is dropped (whether the computer is on or off).
surge protectors — Prevent voltage spikes, such as those that may occur during an electrical storm, from entering the computer through the electrical outlet. Surge protectors do not protect against lightning strikes or against brownouts, which occur when the voltage drops more than 20 percent below the normal AC-line voltage level.
Network connections cannot be protected by surge protectors. Always disconnect the network cable from the network connector during electrical storms.
SVGA — super-video graphics array — A video standard for video cards and controllers. Typical SVGA resolutions are 800 x 600 and 1024 x 768.
The number of colors and resolution that a program displays depends on the capabilities of the monitor, the video controller and its drivers, and the amount of video memory installed in the computer.
S-video TV-out — A connector used to attach a TV or digital audio device to the computer.
SXGA — super-extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1280 x 1024.

SXGA+ — super-extended graphics array plus — A video standard for video cards and controllers that supports resolutions up to 1400 x 1050.
system board — The main circuit board in your computer. Also known as the motherboard.
system setup — A utility that serves as an interface between the computer hardware and the operating system. System setup allows you to configure user- selectable options in the BIOS, such as date and time or system password. Unless you understand what effect the settings have on the computer, do not change the settings for this program.
TAPI — telephony application programming interface — Enables Windows programs to operate with a wide variety of telephony devices, including voice, data, fax, and video.
text editor — A program used to create and edit files that contain only text; for example, Windows Notepad uses a text editor. Text editors do not usually provide word wrap or formatting functionality (the option to underline, change fonts, and so on).
TPM — trusted platform module — A hardware-based security feature that when combined with security software enhances network and computer security by enabling features such as file and e-mail protection.
travel module — A plastic device designed to fit inside the module bay of a portable computer to reduce the weight of the computer.
UMA — unified memory allocation — System memory dynamically allocated to video.
UPS — uninterruptible power supply — A backup power source used when the electrical power fails or drops to an unacceptable voltage level. A UPS keeps a computer running for a limited amount of time when there is no electrical power. UPS systems typically provide surge suppression and may also provide voltage regulation. Small UPS systems provide battery power for a few minutes to enable you to shut down your computer.
USB — universal serial bus — A hardware interface for a low-speed device such as a USB-compatible keyboard, mouse, joystick, scanner, set of speakers, printer, broadband devices (DSL and cable modems), imaging devices, or storage devices. Devices are plugged directly in to a 4-pin socket on your computer or in to a multi-port hub that plugs in to your computer. USB devices can be connected and disconnected while the computer is turned on, and they can also be daisy-chained together.
UTP — unshielded twisted pair — Describes a type of cable used in most telephone networks and some computer networks. Pairs of unshielded wires are twisted to protect against electromagnetic interference, rather than relying on a metal sheath around each pair of wires to protect against interference.
UXGA — ultra extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1600 x 1200.
video controller — The circuitry on a video card or on the system board (in computers with an integrated video controller) that provides the video capabilities—in combination with the monitor—for your computer.
video memory — Memory that consists of memory chips dedicated to video functions. Video memory is usually faster than system memory. The amount of video memory installed primarily influences the number of colors that a program can display.
video mode — A mode that describes how text and graphics are displayed on a monitor. Graphics-based software, such as Windows operating systems, displays in video modes that can be defined as x horizontal pixels by y vertical pixels by z colors. Character-based software, such as text editors, displays in video modes that can be defined as x columns by y rows of characters.
video resolution — See resolution.
virus — A program that is designed to inconvenience you or to destroy data stored on your computer. A virus program moves from one computer to another through an infected disk, software downloaded from the Internet, or e-mail attachments. When an infected program starts, its embedded virus also starts.
A common type of virus is a boot virus, which is stored in the boot sectors of a floppy disk. If the floppy disk is left in the drive when the computer is shut down and then turned on, the computer is infected when it reads the boot sectors of the floppy disk expecting to find the operating system. If the computer is infected, the boot virus may replicate itself onto all the floppy disks that are read or written in that computer until the virus is eradicated.
V — volt — The measurement of electric potential or electromotive force. One V appears across a resistance of 1 ohm when a current of 1 ampere flows through that resistance.
W — watt — The measurement of electrical power. One W is 1 ampere of current flowing at 1 volt.
WHr — watt-hour — A unit of measure commonly used to indicate the approximate capacity of a battery. For example, a 66-WHr battery can supply 66 W of power for 1 hour or 33 W for 2 hours.
wallpaper — The background pattern or picture on the Windows desktop. Change your wallpaper through the Windows Control Panel. You can also scan in your favorite picture and make it wallpaper.
WLAN — wireless local area network. A series of interconnected computers that communicate with each other over the air waves using access points or wireless routers to provide Internet access.

write-protected — Files or media that cannot be changed. Use write-protection when you want to protect data from being changed or destroyed. To write- protect a 3.5-inch floppy disk, slide its write-protect tab to the open position.
WWAN — wireless wide area network. A wireless high-speed data network using cellular technology and covering a much larger geographic area than WLAN.
WXGA — wide-aspect extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1280 x 800.
XGA — extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1024 x 768.
ZIF — zero insertion force — A type of socket or connector that allows a computer chip to be installed or removed with no stress applied to either the chip or its socket.
Zip — A popular data compression format. Files that have been compressed with the Zip format are called Zip files and usually have a filename extension of .zip. A special kind of zipped file is a self-extracting file, which has a filename extension of .exe. You can unzip a self-extracting file by double-clicking it.
Zip drive — A high-capacity floppy drive developed by Iomega Corporation that uses 3.5-inch removable disks called Zip disks. Zip disks are slightly larger than regular floppy disks, about twice as thick, and hold up to 100 MB of data.

Addressing Memory With 4-GB or Greater Configurations (32-bit Operating Systems Only)
Your computer supports non-ECC DDR2 memory only. For more information on the type of memory supported by your computer, see the "Memory" section of the specifications for your computer:
l Mini Tower Computer (Model #DCSM) Specifications
l Desktop Computer (Model # DCNE) Specifications
l Small Form Factor Computer (Model # DCCY) Specifications
Dual-channel DDR2 memory modules should be installed in pairs of matched memory size. If the DDR2 memory modules are not installed with the same amount of memory in each channel, the computer will continue to operate, but with a slight reduction in performance. See the label in the upper-right corner of the module to determine the module's capacity.

The recommended memory configurations are:
l A pair of matched memory modules installed in connectors DIMM1 and DIMM2
l A memory module installed in connector DIMM1
l A pair of matched memory modules installed in connectors DIMM1 and DIMM2 and another matched pair installed in connectors DIMM3 and DIMM4
Be sure to install a single memory module in DIMM1, the connector closest to the edge of the system board, before you install modules in the other connectors.

A matched pair of memory modules in connectors DIMM1 and DIMM2 (white securing clips)
B matched pair of memory modules in connectors DIMM3 and DIMM4 (black securing clips).

This computer supports a maximum of 8 GB of memory. Current 32-bit operating systems, such as Microsoft® Windows® XP, can use a maximum of 4 GB of address space; however, the amount of memory available to the operating system is less than that installed. Certain components within the computer require address space in the 4-GB range. Any address space reserved for these components cannot be used by computer memory.
The following components require memory address space:
l Integrated PCI devices, such as network connectors and SCSI controllers
l PCI Express cards (if applicable)
At start-up, the BIOS identifies the components that require address space. The BIOS dynamically calculates the amount of reserved address space required. The BIOS then subtracts the reserved address space from 4 GB to determine the amount of usable space.
l If the total installed computer memory is less than the usable address space, all installed computer memory is available for use only by the operating
system.
l If the total installed computer memory is equal to or greater than the usable address space, a portion of installed memory is not available for use by
the operating system.
NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. If possible, do not pair an original memory module with a new memory module. Otherwise, your computer may not start properly. You should install your original memory modules in pairs either in connectors DIMM1 and DIMM2 or connectors DIMM3 and DIMM4.
l a desktop computer: remove the optical drive (see Removing an Optical Drive).
l a small form factor computer: first remove the optical drive (see Removing an Optical Drive)then remove the floppy drive or Media Card Reader.
(see Removing a Floppy Drive or Media Card Reader). 3. Carefully press out the securing clip at each end of the memory module connector.

1 securing clip (2) 2 memory module
l a desktop computer: replace the optical drive (see Installing an Optical Drive).
l a small form factor computer: first replace the floppy drive or media card reader (see Installing a Floppy Drive or Media Card Reader) and then
replace the optical drive (see Installing an Optical Drive). 6. Replace the computer cover (see Replacing the Computer Cover).

l a desktop computer: remove the optical drive (see Removing an Optical Drive).
l a small form factor computer: first remove the optical drive (see Removing an Optical Drive) and then remove the floppy drive or media card
reader (see Removing a Floppy Drive or Media Card Reader). 3. Press out the securing clip at each end of the memory module connector.

1 memory connector closest to processor 2 connector 3 securing clips (2)

1 cutouts (2) 2 memory module 3 notch
If you insert the module correctly, the securing clips snap into the cutouts at each end of the module.
4 crossbar


l a desktop computer: replace the optical drive (see Installing an Optical Drive).
l a small form factor computer: first replace the floppy drive or media card reader (see Installing a Floppy Drive or Media Card Reader) and then
replace the optical drive (see Installing an Optical Drive). 7. Replace the computer cover (see Replacing the Computer Cover). 8. The computer detects that the new memory does not match the existing configuration information and generates the following message:
The amount of system memory has changed. Strike the F1 key to continue, F2 to run the setup utility
The computer should have changed the value of System Memory to reflect the newly installed memory. Verify the new total. If it is correct, skip to step 11.
10. If the memory total is incorrect, turn off and disconnect your computer and devices from their electrical outlets. Open the computer cover and check the installed memory modules to ensure that they are seated properly in their sockets. Then repeat steps 7, 8, and 9. 11. When the System Memory total is correct, press to exit system setup. 12. Run the Dell Diagnostics (see Dell Diagnostics) to verify that the memory modules are operating properly.

PCI, PCI Express Cards, and PS/2 Serial Port Adapters
Your Dell™ computer supports a PS/2 serial adapter and provides the following connectors for PCI and PCI Express cards.
l Two PCI card slots
l One PCI Express x16 card slot
l One PCI Express x1 card slot

1 card retention latch 2 alignment guide 3 card
4 card-edge connector 5 card connector 6 release tab


1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors). 11. If you installed a network adapter card and want to turn off the integrated network adapter:
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 12. Install any drivers required for the card as described in the card documentation.

1 card retention latch 2 alignment guide 3 card
4 card-edge connector 5 card connector 6 release tab
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer. 11. If you removed an network-adapter card connector:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.
Your computer supports one PCI Express x16 card and one PCI Express x1 card. See System Board Components for the location of the PCI Express card slots.

1 PCI Express x1 card 2 PCI Express x16 card 3 PCI Express x16 DVI card
4 PCI Express x1 card slot 5 PCI Express x16 card slot 6 PCI Express x16 DVI card slot
If you are replacing a card, uninstall the driver for the existing card. See the documentation that came with the card for instructions.
1 card retention latch 2 alignment guide 3 card
4 card-edge connector 5 card connector 6 release tab
If necessary, disconnect any cables connected to the card. Then continue with step 6.
See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your computer.


1 PCI Express x1 card 2 PCI Express x1 card connector
1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
See the documentation for the card for information about the card's cable connections.
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup. b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer. Back-Panel Connectors. 12. If you installed a network adapter card and want to turn off the integrated network adapter:
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup. b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 13. Install any drivers required for the card as described in the card documentation.

1 card retention latch 2 alignment guide 3 card
4 card-edge connector 5 card connector 6 release tab
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.


1 PCI Express x16 card 2 PCI Express x16 card connector

1 PCI Express x16 card 2 DVI-card connector 3 PCI Express x16 card connector
1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 11. Install any drivers required for the card as described in the card documentation.
If you are removing a PCI Express x16 card, go to step 5.
If you are removing a DVI-card, go to step 6

1 PCI Express x16 card 2 lever 3 securing slot
4 securing tab 5 PCI Express x16 card connector


1 PCI Express x16 DVI-card 2 removal pull tab 3 DVI-card connector
4 lever 5 securing slot 6 securing tab
7 PCI Express x16 card connector
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.


1 card retention latch 2 alignment guide
1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
Before you close the card retention mechanism, ensure that:
l The tops of all adapters and filler brackets are flush with the alignment bar.
l The notch in the top of the adapter or filler bracket fits around the alignment guide.
l Close the card retention latch and gently press until it snaps into place.

1 card retention latch 2 alignment guide
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.

Processor
Lay the heat sink assembly down on its top, with the thermal grease facing upward.

1 heat sink assembly 2 captive screw housings (2)
Processor


1 processor 2 release lever 3 socket
Leave the release lever extended in the release position so that the socket is ready for the new processor and go to Installing the Processor.


1 socket and processor pin-1 indicator 2 processor 3 release lever
a. Place the heat sink assembly back onto the heat-sink assembly bracket. b. Rotate the heat sink assembly down towards the computer base and ensure that the two captive screws are properly aligned with the holes in the system board. c. Tighten the two captive screws.

1 heat sink assembly 2 heat-sink assembly bracket 3 captive screw housing (2)
4 processor socket


Drives
Your computer supports:
l Two SATA (Serial ATA) hard drives
l One optional floppy drive or Media Card Reader
l Two optical drives

1 optical drive 2 floppy drive or media card reader 3 hard drive
Connect SATA hard drives to the connectors labeled "SATA0" or "SATA1." Connect SATA CD or DVD drives to the connectors labeled "SATA2" or "SATA3" on the system board (see System Board Components for information about mini tower system board connectors).
When you install a drive, you connect two cables—a DC power cable and a data cable—to the back of the drive and to the system board.
1 interface cable connector 2 interface connector
Drives · Serial ATA Connector

Interface connectors are keyed for correct insertion.
Serial ATA Power Connector

1 power cable 2 power input connector
When connecting and disconnecting a SATA data cable, hold the cable by the black connector at each end.


1 hard-drive cable 2 hard-drive cable on system board 3 power cable

1 hard drive 2 release tabs (2)
a. Remove the bracket from the existing drive by gently spreading the plastic hard-bracket and removing the hard drive. b. Install the replacement drive into the bracket by inserting the drive into the bracket so that the bracket alignment tabs snaps into the mounting holes on the new drive.


1 hard drive 2 hard-drive bracket

1 hard drive 2 hard drive mounting holes 3 hard-drive bracket
4 bracket alignment tabs

5. Connect the power and hard-drive cables to the drive. 6. Check all connectors to be certain that they are properly cabled and firmly seated. 7. Replace the computer cover (see Replacing the Computer Cover). 8. If the drive you just installed is the primary drive, insert a bootable medium into your boot drive. See the documentation that came with the drive for instructions on installing any software required for drive operation. 9. Enter system setup and update the appropriate Primary Drive option (0 or 1) (see Entering System Setup). 10. Exit system setup, and reboot the computer.

See the documentation for your operating system for instructions.
1. Check the documentation for the drive to verify that it is configured for your computer. 2. Follow the procedures in Before You Begin. 3. Remove the plastic hard-drive bracket from the inside of the hard-drive bay by squeezing the release tabs and gently pulling the bracket up and out of the bay. 4. Install the new drive into the bracket by inserting the drive into the bracket so that the bracket alignment tabs snaps into the mounting holes on the new drive.

1 hard drive 2 hard drive mounting holes 3 hard-drive bracket
4 bracket alignment tabs



1 hard-drive data cable
2 hard-drivedata cable on system board
3 hard-drive power cable
If you are installing a new floppy drive, media card reader, or optical drive instead of replacing a drive, remove the drive-panel inserts.


1 drive panel 2 release tab 3 drive-panel insert

1 optical-drive panel insert
2 floppy-drive/media card reader panel insert
3 holder for shoulder screws
The drive panel only fits one way.


1. Follow the procedures in Before You Begin. 2. Remove the drive panel by sliding the drive release latch in the direction indicated on the latch to open the panel. Then remove it from the hinges. 3. Disconnect the power and floppy-drive cables from the back of the floppy drive. 4. Slide the drive release latch in the direction indicated on the latch until the floppy drive is released; while holding the latch open, slide the drive out of the computer.

1 floppy drive 2 drive release latch



1 floppy drive 2 shoulder screws (4) 3 shoulder screw slots (2)

1 power cable 2 floppy-drive data cable
3 floppy-drive connector on system board (DSKT)

1. Follow the procedures in Before You Begin. 2. Remove the drive panel by sliding the drive release latch in the direction indicated on the latch to open the panel. Then remove it from the hinges. 3. Disconnect the media card reader cable from the back of the media card reader. 4. Slide the drive release latch in the direction indicated on the latch until the media card reader is released; while holding the latch open, slide the device out of the computer.

1 media card reader 2 media card reader cable 3 drive release latch
1. If you are replacing a media card reader, remove the shoulder screws from the existing device and attach the screws to the replacement device. 2. If you are installing a new media card reader, remove the drive-panel insert (see Drive-Panel Inserts) for your new device, remove the shoulder screws from the inside of the drive-panel insert and attach the screws to the new device. 3. Align the shoulder screws on the media card reader with the shoulder screw slots, and gently slide the device into the bay until it clicks into place. 4. Attach the media card reader cable to the media card reader. 5. Connect the media card reader cable to the USB1 connector on the system board (see System Board Components for the connector location).

1 media card reader 2 shoulder screws (4) 3 shoulder screw slots (2)
4 media card reader cable

1. Follow the procedures in Before You Begin. 2. Remove the drive panel by sliding the drive release latch in the direction indicated on the latch to open the panel. Then remove it from the hinges. 3. Disconnect the power and optical drive cables from the back of the drive. 4. Slide the drive release latch in the direction indicated on the latch until the optical drive is released; while holding the latch open, slide the drive out of the computer.

1 optical drive 2 drive release latch



1 optical drive 2 shoulder screws (3) 3 shoulder screw slots (2)

1 power cable 2 optical drive cable 3 optical drive connector (SATA)
See the documentation that accompanied the drive and controller card to verify that the configuration is correct for your computer. Change any settings necessary for correct configuration.
7. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 8. Install the drive panel to the front of the computer. The drive panel only fits one way (see Drive-Panel Inserts). 9. Replace the computer cover (see Replacing the Computer Cover). 10. Update your configuration information in system setup (see System Setup) by setting the appropriate Drive option (0 or 1) under Drives. 11. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics).



Mini Tower Computer
About Your Computer Finding Information Mini Tower Computer Mini Tower Computer (Model # DCSM) Specifications Advanced Features Cleaning Your Computer Reinstalling Drivers and the Operating System Solving Problems Microsoft® Windows® XP and Windows Vista® Features Troubleshooting Tools and Utilities Getting Help Warranty FCC Regulatory Model (U.S. Only) Glossary
Removing and Replacing Parts Before You Begin Removing the Computer Cover Chassis Intrusion Switch I/O Panel Drives PCI, PCI Express Cards, and PS/2 Serial Port Adapters Power Supply Processor Battery Replacing the System Board Memory Replacing the Computer Cover
Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, OptiPlex, Inspiron, Dimension, Latitude, Dell Precision, DellNet, TravelLite, Dell OpenManage, PowerVault, Axim, PowerEdge, PowerConnect, and PowerApp are trademarks of Dell Inc.; AMD, AMD Athlon, AMD Phenom, and combinations thereof, and Cool 'n' Quiet are trademarks of Advanced Micro Devices, Inc; Microsoft and Windows are registered trademarks of Microsoft Corporation; IBM is a registered trademark of International Business Machines Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
March 2008 RP699 Rev. A03

I/O Panel
Removing the I/O Panel

1 I/O panel release button 2 securing screw 3 I/O panel
4 I/O cable connector 5 pull-loop
To replace the I/O panel, follow the removal procedure in the reverse order.
I/O Panel



Power Supply
Replacing the Power Supply

1 release button 2 power supply 3 screws (4)
4 AC power connector
Power Supply










Removing the Computer Cover

1 security cable slot 2 cover release latch 3 padlock ring

Mini Tower Computer (Model #DCSM) Specifications
Microprocessor type AMD Phenom™ processors
AMD Athlon™ 64 X2 Dual-Core processor
AMD Athlon 64 X2:1-MB L2 dedicated cache
Type 533-, 667-, or 800-MHz DDR2 SDRAM
Memory modules supported 256 MB, 512 MB, 1 GB, or 2 GB non-ECC
Maximum memory 8 GB
Chipset nVidia GeForce 6150LE/Nforce 430
RAID support RAID 0 and RAID 1
Data bus width 64 bits
Address bus width 40 bits
BIOS chip (NVRAM) 8 Mb or 4 Mb
NIC support for Atmel 1-Mb and 2-Mb EEPROM

Capable of 10/100/1000 communication
Type nVidia integrated video (DirectX 9.0c Shader Model 3.0 Graphics Processing Unit) or PCI Express x16 graphics card or DVI graphics card
Type Sigma Tel 9200 CODEC (2.1 Channel Audio)
Stereo conversion 24-bit analog-to-digital; 24-bit digital-to-analog
Drives two SATA controllers supporting two devices each, including two 3.5-inch hard drives
Bus type PCI 2.3 PCI Express 1.0A SATA 1.0A and 2.0 USB 2.0
Bus speed PCI: 133 MB/s PCI Express x16: 40 GB/s bidirectional speed PCI Express x1: 2.5 Gbps SATA: 1.5 Gbps and 3.0 Gbps USB: 480-Mbps high speed, 12-Mbps full speed, 1.2- Mbps low speed
connector size 124 pins
PCI Express:
connectors one x1 and one x16
power 10 W (x1) and 75 W (x16) maximum
connector size 36 pins (x1) and 164 pins (x16)
connector data width (maximum) one PCI Express lane (x1) and 16 PCI Express lanes (x16)
Externally accessible two 3.5-inch drive bays, including support for up to two 3.5-inch hard drives two 5.25-inch drive bays
Internally accessible two bays for 1-inch-high hard drives
External connectors:
Serial 9-pin connector; 16550C-compatible
Parallel 25-hole connector (bidirectional)
Video 15-hole VGA connector
Optional DVI 36-pin connector
Network adapter RJ45 connector
Optional PS/2 with secondary serial port adapter

USB two front-panel and five back-panel USB 2.0– compliant connectors
Audio two connectors for line-in and line-out; two front- panel connectors for headphones and microphone
System board connectors:
SATA four 7-pin connectors
Floppy drive 34-pin connector
Serial 24-pin connector for optional second serial port card
PCI 2.3 two 124-pin connectors
Internal USB 10-pin connector
Intrusion switch 3-pin connector
Memory modules four 240-pin connector
Power 12V 4-pin connector
Front panel 40-pin connector
in Microsoft® Windows® XP and Windows Vista®, brings up the Windows Security window. If in MS- DOS® mode, restarts (reboots) the computer.
or starts embedded system setup (during start-up only)
or displays a boot device menu that allows the user to enter a device for a single boot (during start-up only) as well as options to run hard-drive and system diagnostics
starts the RAID setup menu if RAID is turned on in the system setup program
disables computer password at start-up (after correct password is entered)
Power control front of chassis - push button
Power light (within the power button) green light — Blinking green indicates sleep mode; solid green indicates power-on state.
amber light — Blinking amber indicates a problem with an installed device; solid amber indicates an internal power problem (see Power Problems).
Hard-drive access light front panel - green
Link light (on front panel) front panel - solid green light indicates network connection
Link integrity light (on integrated network adapter) rear panel - green light for 10-Mb operation; orange light for 100-Mb operation; yellow light for a 1000-Mb (1-Gb) operation
Activity light (on integrated network adapter) rear panel - yellow blinking light
Diagnostic lights front panel - four lights on the front panel. See Diagnostic Lights.
Standby power light AUX_PWR on the system board
DC power supply:
Heat dissipation 1040.7 BTU/hr maximum
Voltage manual selection power supplies—90 to 135 V at 50/60 Hz; 180 to 265 V at 50/60 Hz
Backup battery 3-V CR2032 lithium coin cell


Operating 0.25 G at 3 to 200 Hz at 0.5 octave/min
Storage 0.5 G at 3 to 200 Hz at 1 octave/min
Operating bottom half-sine pulse with a change in velocity of 50.8 cm/sec (20 inches/sec)
Storage 27-G faired square wave with a velocity change of 508 cm/sec (200 inches/sec)
Operating –15.2 to 3048 m (–50 to 10,000 ft)
Storage –15.2 to 10,668 m (–50 to 35,000 ft)
Airborne contaminant level G2 or lower as defined by ISA-S71.04-1985

Speaker
Installing a Speaker

Speaker



Transferring Information to a New Computer
User Accounts and Fast User Switching
Setting Up a Home and Office Network
You can use your operating system "wizards" to help you transfer files and other data from one computer to another—for example, from an old computer to a new computer. For instructions, see the following section that corresponds to the operating system that your computer is running.
Follow the instructions provided on the screen by the Windows Easy Transfer wizard.
The Microsoft Windows XP operating system provides the Files and Settings Transfer Wizard to move data from a source computer to a new computer. You can transfer data, such as:
You can transfer the data to the new computer over a network or serial connection, or you can store it on removable media, such as a writable CD, for transfer to the new computer.
NOTE: You can transfer information from an old computer to a new computer by directly connecting a serial cable to the input/output (I/O) ports of the two computers. To transfer data over a serial connection, you must access the Network Connections utility from the Control Panel and perform additional configuration steps, such as setting up an advanced connection and designating the host computer and the guest computer. For instructions on setting up a direct cable connection between two computers, see Microsoft Knowledge Base Article #305621, titled How to Set Up a Direct Cable Connection Between Two Computers in Windows XP. This information may not be available in certain countries.
For transferring information to a new computer, you must run the Files and Settings Transfer Wizard. You can use the optional Operating System media for this process or you can create a wizard disk with the Files and Settings Transfer Wizard.
To prepare a new computer for the file transfer:
1. Open the Files and Settings Transfer Wizard: click Start® All Programs® Accessories® System Tools® Files and Settings Transfer Wizard. 2. When the Files and Settings Transfer Wizard welcome screen appears, click Next. 3. On the Which computer is this? screen, click New Computer® Next. 4. On the Do you have a Windows XP CD? screen, click I will use the wizard from the Windows XP CD® Next. 5. When the Now go to your old computer screen appears, go to your old or source computer. Do not click Next at this time.
To copy data from the old computer:

1. On the old computer, insert the Windows XP Operating System media. 2. On the Welcome to Microsoft Windows XP screen, click Perform additional tasks. 3. Under What do you want to do?, click Transfer files and settings® Next. 4. On the Which computer is this? screen, click Old Computer® Next. 5. On the Select a transfer method screen, click the transfer method you prefer. 6. On the What do you want to transfer? screen, select the items you want to transfer and click Next.
After the information has been copied, the Completing the Collection Phase screen appears.
To transfer data to the new computer:
The wizard reads the collected files and settings and applies them to your new computer.
When all of the settings and files have been applied, the Finished screen appears.
To run the Files and Settings Transfer Wizard without the Operating System media, you must create a wizard disk that will allow you to create a backup image file to removable media.
To create a wizard disk, use your new computer with Windows XP and perform the following steps:
1. Open the Files and Settings Transfer Wizard: click Start® All Programs® Accessories® System Tools® Files and Settings Transfer Wizard. 2. When the Files and Settings Transfer Wizard welcome screen appears, click Next. 3. On the Which computer is this? screen, click New Computer® Next. 4. On the Do you have a Windows XP CD? screen, click I want to create a Wizard Disk in the following drive® Next. 5. Insert the removable media, such as a writable CD, and click OK. 6. When the disk creation completes and the Now go to your old computer message appears, do not click Next. 7. Go to the old computer.
To copy data from the old computer:
1. On the old computer, insert the wizard disk. 2. Click Start® Run. 3. In the Open field on the Run window, browse to the path for fastwiz (on the appropriate removable media) and click OK. 4. On the Files and Settings Transfer Wizard welcome screen, click Next. 5. On the Which computer is this? screen, click Old Computer® Next. 6. On the Select a transfer method screen, click the transfer method you prefer. 7. On the What do you want to transfer? screen, select the items you want to transfer and click Next.
After the information has been copied, the Completing the Collection Phase screen appears.

To transfer data to the new computer:
The wizard reads the collected files and settings and applies them to your new computer.
When all of the settings and files have been applied, the Finished screen appears.
My Old Computer To My New Dell™ Computer Using the Microsoft® Windows® XP Operating System?).
Adding User Accounts
After the operating system is installed, the administrator or a user with administrator rights can create additional user accounts.
If the User Account Control dialog box appears, click Continue or type an administrator password and click Submit.
The new account name appears in the User Accounts window.
l Computer administrator — You can change all computer settings.
l Limited — You can change only your own personal settings, such as your password. You cannot install programs or use the Internet.

Fast User Switching allows multiple users to access one computer without requiring the previous user to log off.
The current user's name and picture appear on the Start menu.
The user's name and picture now appear in the Start menu.
When you use Fast User Switching, programs that previous users were using remain running in the background, which might decrease your computer's response time. Also, multimedia programs, such as games and DVD software, might not work with Fast User Switching. For more information, see the Windows Help and Support Center.
Connecting to a Network Adapter
Insert the cable until it clicks into place, and then gently pull it to ensure that it is secure.


1 network adapter connector 2 network device 3 network cable
4 network adapter connector on computer
The Microsoft® Windows® XP operating system provides a Network Setup Wizard to guide you through the process of sharing files, printers, or an Internet connection between computers in a home or small office.

Gently pull the power cables toward you so that they do not get caught underneath the drives.
a. Align the bottom of the cover with the hinge tabs located along the bottom edge of the computer. b. Using the hinge tabs as leverage, rotate the cover downward until it snaps into place.

c. Ensure that the cover is seated correctly before moving the computer.
After you remove and replace the cover, the chassis intrusion detector, if installed and enabled, causes the following message to appear on the screen at the next computer start-up:
ALERT! Cover was previously removed.

PCI, PCI Express Cards, and PS/2 Serial Port Adapters
Your Dell™ computer supports a PS/2 serial port adapter and provides the following connectors for PCI and PCI Express cards:
l One low-profile PCI card slot
l One low-profile PCI Express x16 card slot

1 release tab 2 card retention latch 3 card
4 card-edge connector 5 card connector


1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
l The tops of all cards and filler brackets are flush with the alignment guide
l The notch in the top of the card or filler bracket fits around the alignment guide
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 13. Install any drivers required for the card as described in the card documentation.


1 release tab 2 card retention latch 3 card
4 card-edge connector 5 card connector
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.
Your computer supports one low-profile PCI Express x16 card.
If you are replacing a PCI Express card with a different type of PCI Express card, remove the current driver for the card from the operating system. See the documentation that came with the card for information.

2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open. 3. If you are installing a new PCI Express x16 card or DVI card, remove the filler bracket to create a card- slot opening. Then continue with step 5. 4. If you are replacing a PCI Express x16 card or DVI card, remove the card (see Removing a PCI Express x16 Card or DVI Card). If necessary, disconnect any cables connected to the card. Then continue with step 6. 5. Prepare the card for installation.
1 PCI Express x16 card 2 PCI Express x16 card connector
1 PCI Express x16 DVI-card 2 DVI card connector 3 PCI Express x16 card connector


1 fully seated card 2 not fully seated card 3 bracket within slot
4 bracket caught outside of slot
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).
a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 13. Install any drivers required for the card as described in the card documentation.
If you are removing a PCI Express x16 card, go to step 5.
If you are removing a DVI card, go to step 6


1 PCI Express x16 card 2 lever 3 securing slot (not all cards)
4 securing tab 5 PCI Express x16 card connector

1 PCI Express x16 DVI-card 2 removal pull tab 3 DVI card connector
4 lever 5 securing slot 6 securing tab
7 PCI Express x16 card connector
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.
a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.
l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.

1 release tab 2 adapter retention latch 3 serial port adapter bracket
4 serial port adapter connector
5 serial port adapter system board connector (PS2/SER2)

l The tops of all cards and filler brackets are flush with the alignment bar.
l The notch in the top of the card or filler bracket fits around the alignment guide.

Processor

1 heat sink assembly 2 captive screws in housing (2)
Processor


1 processor 2 release lever 3 socket
Leave the release lever extended in the release position so that the socket is ready for the new processor, and go to Installing the Processor.


1 socket and processor pin-1 indicator 2 processor 3 release lever
a. Place the heat sink assembly back onto the heat-sink assembly bracket. b. Rotate the heat sink assembly down towards the computer base and ensure that the two captive screws are properly aligned with the holes in the system board c. Tighten the two captive screws.

1 heat sink assembly 2 heat-sink assembly bracket 3 captive screw in housing (2)
4 processor socket



Removing the Computer Cover
1. Follow the procedures in Before You Begin. 2. If you have installed a padlock through the padlock ring on the back panel, remove the padlock. 3. Locate the cover release latch shown in the illustration. Then, slide the release latch back as you lift the cover. 4. Grip the sides of the computer cover and pivot the cover up using the bottom hinges as leverage points. 5. Remove the cover from the hinge tabs and set it aside on a soft nonabrasive surface.

1 security cable slot 2 cover release latch 3 computer cover

Your computer supports:
l One SATA hard drive
l One floppy drive or Media Card Reader
l One SATA optical drive

1 FlexBay for floppy drive or Media Card Reader 2 optical drive 3 hard drive
When you install a drive, you connect two cables—a DC power cable and a data cable—to the back of the drive.

1 interface cable connector 2 interface connector
Interface connectors are keyed for correct insertion.
Drives · Serial ATA Connector

Serial ATA Power Connector
1 power cable 2 power input connector
When connecting and disconnecting a SATA data cable, hold the cable by the black connector at each end.
1. If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. 2. Check the documentation for the drive to verify that it is configured for your computer. 3. Follow the procedures in Before You Begin. 4. Lay the computer on its side so that the system board is on the bottom of the inside of the computer. 5. Press in on the two blue securing tabs on each side of the drive and slide the drive up and out of the computer.


1 securing tabs (2) 2 hard drive

1 power cable 2 SATA data cable 3 fan cable


1 release tabs (2) 2 drive 3 hard drive bracket

1 power cable 2 SATA data cable 3 fan cable

1 release tabs (2) 2 hard drive
7. Check all connectors to be certain that they are properly cabled and firmly seated. 8. Replace the computer cover (see Replacing the Computer Cover). 9. If the drive you just installed is the primary drive, insert bootable media into your boot drive. 10. Turn on the computer. 11. Enter system setup (see Entering System Setup) and update the appropriate Primary Drive option (0 or 2). 12. Exit system setup, and reboot the computer. 13. Partition and logically format your drive before you proceed to the next step.
For instructions, see the documentation that came with your operating system.
For instructions, see the documentation that came with your operating system.

a. Lift the release tab on the back panel of the fan. b. Rotate the fan in the opposite direction from that indicated by the arrow on the back panel of the fan. c. Lift to remove the fan and its back panel from the hard-drive bracket.

1 fan release tab 2 fan with fan back panel 3 power cable
a. Turn the fan upside-down, so that its backing faces up and align the triangle on the fan's back panel with the corresponding triangle on the back of the hard-drive bracket. b. Rotate the fan and its backing in the direction of the arrow on the fan's back panel. 6. Install the hard drive (see Installing a Hard Drive).
4 hard-drive bracket


1 drive release latch 2 optical drive

1 optical drive 2 data cable 3 power cable

1 optical drive 2 data cable 3 power cable


5. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 6. Replace the computer cover (see Replacing the Computer Cover). 7. See the documentation that came with the drive for instructions on installing any software required for drive operation. 8. Enter system setup and select the appropriate Drive option (see Entering System Setup). 9. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics).


1 cable release tab 2 data cable edge connector

1 Media Card Reader data cable


1 floppy drive or Media Card Reader 2 screws (3) 3 bracket rails (3)
l Installing a new floppy drive or Media Card Reader, remove the drive panel insert
l Replacing a drive, remove the floppy drive or Media Card Reader (see Floppy Drive and Media Card Reader).
l A floppy drive: insert the data cable into the cable release tab on the floppy drive and press down on the tab until it clicks to lock it in place.
l A Media Card Reader: insert the cable into the connector on the Media Card Reader.
l A floppy drive: insert the data cable into the connector on the system board.

1 cable release tab 2 floppy drive data cable edge connector
l A Media Card Reader: remove the hard drive (see Removing a Hard Drive) and connect the cable to the system board connector labeled "USB1
(see System Board Components).


1 media card reader data cable
See the documentation that came with the drive for instructions on installing any software required for drive operation.

Small Form Factor Computer
About Your Computer Finding Information Small Form Factor Computer Small Form Factor Computer (Model # DCCY) Specifications Advanced Features Cleaning Your Computer Reinstalling Drivers and the Operating System Solving Problems Microsoft® Windows® XP and Windows Vista® Features Troubleshooting Tools and Utilities Getting Help Warranty FCC Regulatory Model (U.S. Only) Glossary
Removing and Replacing Parts Before You Begin Removing the Computer Cover Chassis Intrusion Switch I/O Panel Drives PCI, PCI Express Cards, and PS/2 Serial Port Adapters Power Supply Processor Battery Replacing the System Board Memory Replacing the Computer Cover
Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, OptiPlex, Inspiron, Dimension, Latitude, Dell Precision, DellNet, TravelLite, Dell OpenManage, PowerVault, Axim, PowerEdge, PowerConnect, and PowerApp are trademarks of Dell Inc.; AMD, AMD Athlon, AMD Phenom, and combinations thereof, and Cool 'n' Quiet are trademarks of Advanced Micro Devices, Inc; Microsoft and Windows are registered trademarks of Microsoft Corporation; IBM is a registered trademark of International Business Machines Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
March 2008 RP699 Rev. A03

I/O Panel
Removing the I/O Panel
a. Disconnect the fan connector. b. Disconnect the fan control cable. c. Press the tab that secures the fan to the interior base of the computer and lift the fan from the computer; set the fan aside in the chassis.

1 fan control ribbon cable 2 fan release tab 3 fan cable
I/O Panel


1 fan cable connector 2 air temperature sensor cable 3 I/O cable connector
4 screw 5 I/O panel

Power Supply
Replacing the Power Supply

1 power supply 2 screw
6. Slide the power supply toward the front of the computer approximately 1 inch. 7. Lift the power supply up and out of the computer. 8. Slide the replacement power supply into place. 9. Replace the screws that secure the power supply to the back of the computer chassis. 10. Reconnect the DC power cables to the system board and drives (see System Board Components for connector locations). 11. Replace the floppy drive or Media Card Reader (see Installing a Floppy Drive or Media Card Reader).
Power Supply










Small Form Factor Computer (Model # DCCY) Specifications
Microprocessor type AMD Phenom™ processors
AMD Athlon™ 64 X2 Dual-Core processor
AMD Athlon 64 X2:1-MB L2 dedicated cache
Type 667- or 800-MHz DDR2 SDRAM
Memory modules supported 256 MB, 512 MB, 1 GB, or 2 GB non-ECC
Maximum memory 8 GB
Chipset nVidia GeForce 6150LE/NForce 430
Data bus width 64 bits
Address bus width 40 bits
BIOS chip (NVRAM) 8 Mb or 4 Mb
NIC integrated network interface with ASF 1.03 and 2.0 support as defined by DMTF
Capable of 10/100/1000 communication


Type nVidia integrated video (DirectX 9.0c Shader Model 3.0 Graphics Processing Unit), PCI Express x16 graphics card, or DVI graphics card.
Bus type PCI 2.3 PCI Express 1.0A SATA 1.0A and 2.0 USB 2.0
PCI Express x16: 40 GB/s bidirectional speed SATA: 1.5 Gbps and 3.0 Gbps USB: 480-Mbps high speed, 12-Mbps full speed, 1.2- Mbps low speed
connector data width (maximum) 16 PCI Express lanes (x16)
Externally accessible one 3.5-inch drive one bay for slim optical drive
Internally accessible one bay for a 1-inch-high hard drive

USB two front-panel and five back-panel USB 2.0– compliant connectors
Audio two connectors for line-in and line-out; two front- panel connectors for headphones and microphone
System board connectors:
SATA two 7-pin connectors
Floppy drive 38-pin connector
Serial 24-pin connector for optional second serial port card
Fan two 5-pin connector fans
PCI 2.3 124-pin connector
Internal USB 10-pin connector
Intrusion switch 3-pin connector
Memory modules four 240-pin connectors
Power 12V 4-pin connector
Front panel 40-pin connector
in Microsoft® Windows® XP and Windows Vista, brings up the Windows Security window; in MS-DOS® mode, restarts (reboots) the computer
or starts embedded system setup (during system start- up only)
or displays a boot device menu that allows the user to enter a device for a single boot (during system start- up only) as well as options to run hard-drive and system diagnostics
Power control front of chassis - push button
Power light (within the power button) green light — Blinking green indicates a sleep mode; solid green indicates a power-on state.
amber light — Blinking amber indicates a problem with an installed device; solid amber indicates an internal power problem (see Power Problems).
Hard-drive access light front panel - green
Link light front panel - solid green light indicates network connection
Link integrity light (on integrated network adapter) rear panel - green light for 10-Mb operation; orange light for 100-Mb operation; yellow light for a 1000-Mb (1-Gb) operation
Activity light (on integrated network adapter) rear panel - yellow blinking light
Diagnostic lights front panel - four lights. See Diagnostic Lights.
Standby power light AUX_PWR on the system board
DC power supply:
Heat dissipation 938.85 BTU/hr maximum
Voltage manual selection power supplies — 90 to 135 V at 50/60 Hz; 180 to 265 V at 50/60 Hz
Backup battery 3-V CR2032 lithium coin cell
Height 9.26 cm (3.65 inches)
Width 31.37 cm (12.35 inches)
Depth 34.03 cm (13.40 inches)

Weight 7.4 kg (16.4 lb)
Temperature:
Operating 10° to 35°C (50° to 95°F)
Storage –40° to 65°C (–40° to 149°F)
Relative humidity 20% to 80% (noncondensing)
Maximum vibration:
Operating 0.25 G at 3 to 200 Hz at 0.5 octave/min
Storage 0.5 G at 3 to 200 Hz at 1 octave/min
Maximum shock:
Operating bottom half-sine pulse with a change in velocity of 50.8 cm/sec (20 inches/sec)
Storage 27-G faired square wave with a velocity change of 508 cm/sec (200 inches/sec)
Altitude:
Operating –15.2 to 3048 m (–50 to 10,000 ft)
Storage –15.2 to 10,668 m (–50 to 35,000 ft)
Airborne contaminant level G2 or lower as defined by ISA-S71.04-1985
Environmental

Speaker
Installing a Speaker
Speaker

About Your Small Form Factor Computer
Front View

1 USB 2.0 connectors (2)
Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see System Setup for more information about booting to a USB device).
It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
2 power button Press to turn on the computer.
3 Dell badge This badge can be rotated to match the orientation of your computer. To rotate, place fingers around the outside of the badge, press firmly, and turn the badge. You can also rotate the badge using the slot provided near the bottom of the badge.
4 hard drive activity light
This light flickers when the hard drive is being accessed.
Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see Diagnostic Lights.
6 LAN indicator light
This light indicates that a LAN (local area network) connection is established.
7 power light The power light illuminates and blinks or remains solid to indicate different operating states:
l No light — The computer is turned off.
l Steady green — The computer is in a normal operating state.
l Blinking green — The computer is in a power-saving mode.
l Blinking or solid amber — See Power Problems.
To exit from a power-saving mode, press the power button or use the keyboard or the mouse if it is configured as a wake device in the Windows Device Manager. For more information about sleep modes and exiting from a power-saving mode, see Power Management.
See System Lights for a description of light codes that can help you troubleshoot problems with your computer.
Use the headphone connector to attach headphones and most kinds of speakers.
9 microphone Use the microphone connector to attach a microphone.
Inside Your Computer · 5 diagnostic lights · 8 headphone connector

10 3.5-inch drive bay
Can contain an optional slimline floppy drive or optional slimline media card reader.
11 optical drive Insert a slimline media (if supported) into this drive.

1 card slots Access connectors for any installed PCI and PCI Express cards.
Plug serial, USB, and other devices into the appropriate connectors (see Back-Panel Connectors).
Insert the power cable.
4 voltage selection switch
Your computer is equipped with a manual voltage-selection switch. To help avoid damaging a computer with a manual voltage selection switch, set the switch for the voltage that most closely matches the AC power available in your location.
Also, ensure that your monitor and attached devices are electrically rated to operate with the AC power available in your location.
5 padlock ring Insert a padlock to lock the computer cover.
6 cover release latch
Allows you to open the computer cover.

Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.
2 link integrity light
l Green — A good connection exists between a 10-Mbps network and
the computer.
l Orange — A good connection exists between a 100-Mbps network
and the computer.
l Yellow — A good connection exists between a 1-Gbps (or 1000-
Mbps) network and the computer.
l Off — The computer is not detecting a physical connection to the
network.
3 network adapter connector
To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the

network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached.
On computers with a network connector card, use the connector on the card.
It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.
4 network activity light
Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.
Use the green line-out connector to attach headphones and most speakers with integrated amplifiers.
On computers with a sound card, use the connector on the card.
Use the line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR.
On computers with a sound card, use the connector on the card.
7 USB 2.0 connectors (5)
Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
Plug the cable from your VGA-compatible monitor into the blue connector.
Connect a serial device, such as a handheld device, to the serial port. The default designations are COM1 for serial connector 1 and COM2 for serial connector 2.
For more information, see System Setup Options.


1 drive-release latch 2 optical drive 3 power supply
4 chassis intrusion switch (optional) 5 hard drive 6 card slots (2)
7 system board 8 heat sink assembly


10 CMOS reset jumper (RTCRST) 11 battery socket (BATTERY)
13 standby (AUX_PWR_LED) 14 PCI Express x16 connector (SLOT1)

19 Optional DVI-card connector (DVI_HDR)
20 speaker connector (INT_SPKR)

Restoring Your Operating System
Reinstalling Microsoft® Windows Vista® and Windows® XP
What Is a Driver?
A driver is a program that controls a device such as a printer, mouse, or keyboard. All devices require a driver program.
A driver acts like a translator between the device and any other programs that use the device. Each device has its own set of specialized commands that only its driver recognizes.
Dell ships your computer to you with required drivers already installed—no further installation or configuration is needed.
Many drivers, such as the keyboard driver, come with your Microsoft Windows operating system. You may need to install drivers if you:
l Upgrade your operating system.
l Reinstall your operating system.
l Connect or install a new device.
If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver.
If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver.
Scroll down the list to see if any device has an exclamation point (a yellow circle with a [!]) on the device icon.
If an exclamation point is next to the device name, you may need to reinstall the driver or install a new driver (see Reinstalling Drivers and Utilities).
Drivers · Windows Vista · Windows XP

If an exclamation point is next to the device name, you may need to reinstall the driver or install a new driver.
If a problem occurs on your computer after you install or update a driver, use Windows Device Driver Rollback to replace the driver with the previously installed version.
If Device Driver Rollback does not resolve the problem, then use System Restore (see Restoring Your Operating System) to return your computer to the operating state that existed before you installed the new driver.
If a problem occurs on your computer after you install or update a driver, use Windows XP Device Driver Rollback to replace the driver with the previously installed version.
If Device Driver Rollback does not resolve the problem, then use System Restore (see Enabling System Restore), to return your computer to the operating state that existed before you installed the new driver.
If using Device Driver Rollback or System Restore does not resolve your problem, (see Restoring Your Operating System), then reinstall the driver from the Drivers and Utilities media.
Windows Vista

In most cases, the CD/DVD starts running automatically. If it does not, start Windows Explorer, click your CD/DVD drive directory to display the CD/DVD contents, and then double-click the autorcd.exe file. The first time that you run the CD/DVD, it might prompt you to install setup files. Click OK, and follow the instructions on the screen to continue.
A link or links appear(s) for the specific drivers and utilities used by your computer.
If no Install button is present, automatic installation is not an option. For installation instructions, either see the appropriate instructions in the following subsections, or click Extract, follow the extracting instructions, and then read the readme file.
If instructed to navigate to the driver files, click the CD/DVD directory on the driver information window to display the files associated with that driver.
After extracting the driver files to your hard drive as described in the previous section, do the following:
3. Double-click the type of device for which you are installing the driver (for example, Audio or Video). 4. Double-click the name of the device for which you are installing the driver. 5. Click Driver® Update Driver® Browse my computer for driver software. 6. Click Browse and browse to the location to which you previously copied the driver files. 7. When the name of the appropriate driver appears, click the name of the driver® OK® Next. 8. Click Finish and restart your computer.
If this is your first time to use the Drivers and Utilities media, the Installation window opens to inform you that the media will begin the installation. Click OK and respond to the installation program prompts to complete the installation.
The Drivers and Utilities media scans your computer's hardware and operating system and then displays a list of device drivers for your system configuration.

To view a list of all available drivers for your computer, click Drivers in the Topic drop-down menu.
To access the help files on the Drivers and Utilities media, click the question mark button or the Help link at the top of the screen.
The Microsoft Windows operating system provides System Restore to allow you to return your computer to an earlier operating state (without affecting data files) if changes to the hardware, software, or other system settings have left the computer in an undesirable operating state. See the Windows Help and Support Center for information on using System Restore.
In the event that System Restore did not resolve the issue, you may undo the last system restore.
Creating a Restore Point

The Select a Restore Point screen provides a calendar that allows you to see and select restore points. All calendar dates with available restore points appear in boldface type.
If a calendar date has only one restore point, then that restore point is automatically selected. If two or more restore points are available, click the restore point that you prefer.
The Restoration Complete screen appears after System Restore finishes collecting data and then the computer restarts.
To change the restore point, you can either repeat the steps using a different restore point, or you can undo the restoration.
The System Restore screen appears and the computer restarts.
If you reinstall Windows XP with less than 200 MB of free hard-disk space available, System Restore is automatically disabled. To see if System Restore is enabled:
The reinstallation process can take 1 to 2 hours to complete. After you reinstall the operating system, you must also reinstall the device drivers, virus protection program, and other software.
When the DELL logo appears, press immediately.
Windows Vista

If you are considering reinstalling the Windows XP operating system to correct a problem with a newly installed driver, first try using Windows XP Device Driver Rollback (see Using Windows XP Device Driver Rollback). If Device Driver Rollback does not resolve the problem, then use System Restore (see Restoring Your Operating System) to return your operating system to the operating state it was in before you installed the new device driver.
To reinstall Windows XP, you need the following items:
l Dell™ Operating System media
l Dell Drivers and Utilities media
To reinstall Windows XP, perform all the steps in the following sections in the order in which they are listed.
The reinstallation process can take 1 to 2 hours to complete. After you reinstall the operating system, you must also reinstall the device drivers, virus protection program, and other software.
If the operating system logo appears, wait until you see the Windows desktop, and then shut down the computer and try again.
1. When the Windows XP Setup screen appears, press to select To set up Windows now. 2. Read the information on the Microsoft Windows Licensing Agreement screen, and press to accept the license agreement. 3. If your computer already has Windows XP installed and you want to recover your current Windows XP data, type r to select the repair option, and remove the media. 4. If you want to install a new copy of Windows XP, press to select that option.
Windows XP

The Windows XP Setup screen appears, and the operating system begins to copy files and install the devices. The computer automatically restarts multiple times.
6. When the Regional and Language Options screen appears, select the settings for your location and click Next. 7. Enter your name and organization (optional) in the Personalize Your Software screen, and click Next. 8. At the Computer Name and Administrator Password window, enter a name for your computer (or accept the one provided) and a password, and click Next. 9. If the Modem Dialing Information screen appears, enter the requested information and click Next. 10. Enter the date, time, and time zone in the Date and Time Settings window, and click Next. 11. If the Networking Settings screen appears, click Typical and click Next. 12. If you are reinstalling Windows XP Professional and you are prompted to provide further information regarding your network configuration, enter your selections. If you are unsure of your settings, accept the default selections.
Windows XP installs the operating system components and configures the computer. The computer automatically restarts.
13. When the Welcome to Microsoft screen appears, click Next. 14. When the How will this computer connect to the Internet? message appears, click Skip. 15. When the Ready to register with Microsoft? screen appears, select No, not at this time and click Next. 16. When the Who will use this computer? screen appears, you can enter up to five users. 17. Click Next. 18. Click Finish to complete the setup, and remove the media. 19. Reinstall the appropriate drivers with the Drivers and Utilities media. 20. Reinstall your virus protection software. 21. Reinstall your programs.

E-Mail, Modem, and Internet Problems
Serial or Parallel Device Problems
Lockups and Software Problems
Sound and Speaker Problems
Media Card Reader Problems
Video and Monitor Problems
Follow these tips when you troubleshoot your computer:
l If you added or removed a part before the problem started, review the installation procedures and ensure that the part is correctly installed.
l If a peripheral device does not work, ensure that the device is properly connected.
l If an error message appears on the screen, write down the exact message. This message may help technical support personnel diagnose and fix the
problem(s).
l If an error message occurs in a program, see the program's documentation.
Fill out the Diagnostics Checklist as you complete these checks.
Replace the battery — If you have to repeatedly reset time and date information after turning on the computer, or if an incorrect time or date displays during start-up, replace the battery (see Replacing the Battery). If the battery still does not work properly, contact Dell (see Contacting Dell).
Fill out the Diagnostics Checklist as you complete these checks.
Check the card seating and cable —
For instructions on which cables should be attached to specific connectors on a card, see the card's documentation.

turn them on.
Test the graphics card —
If your primary hard drive is connected to a drive controller card leave the drive controller card installed in the computer.
Test the cards —
1. Turn off the computer and devices, disconnect them from their electrical outlets, wait 10 to 20 seconds, and then remove the computer cover (see Removing the Computer Cover for mini tower computers, or Removing the Computer Cover for desktop computers). 2. Reinstall one of the cards that you removed previously (see PCI, PCI Express Cards, and PS/2 Serial Port Adapters for mini tower computers, or Installing a PCI Card for desktop computers). 3. Close the computer cover, (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on. 4. Run the Dell Diagnostics (see Dell Diagnostics). 5. If any of the tests fail, the card you just reinstalled is faulty and needs to be replaced. 6. Repeat this process until you have reinstalled all cards.
Fill out the Diagnostics Checklist as you complete these checks.
Test the drive —
l Insert another floppy disk, CD, or DVD to eliminate the possibility that the original one is defective.
l Insert bootable media and restart the computer.
Clean the drive or disk — See CDs and DVDs.
Check the cable connections
Check for Software and Hardware Conflicts — See Resolving Software and Hardware Incompatibilities.
Run the Dell Diagnostics — See Dell Diagnostics.
Adjust the Windows volume control —

l Click the speaker icon in the lower-right corner of your screen.
l Ensure that the volume is turned up by clicking the slidebar and dragging it up.
l Ensure that the sound is not muted by clicking any boxes that are checked.
Check the speakers and subwoofer — See Sound and Speaker Problems.
Close other programs — The Optical-RW drive must receive a steady stream of data when writing. If the stream is interrupted, an error occurs. Try closing all programs before you write to the Optical-RW.
Turn off Standby mode in Windows before writing to a Optical-RW disc — See your computer documentation for information on Power Management modes (see Power Management).
Run Check Disk —
Run the Modem Helper diagnostics — Click the Start button, point to All Programs, and then click Modem Helper. Follow the instructions on the screen to identify and resolve modem problems. (Modem Helper is not available on all computers.)
Verify that the modem is communicating with Windows —
If all commands receive responses, the modem is operating properly.
Ensure that you are connected to the Internet — Ensure that you have subscribed to an Internet provider. With the Outlook Express e- mail program open, click File. If Work Offline has a checkmark next to it, click the checkmark to remove it and connect to the Internet. For help, contact your Internet service provider.

Check the keyboard cable —
l Ensure that the keyboard cable is firmly connected to the computer.
l Shut down the computer, reconnect the keyboard cable as shown in the Quick Reference Guide for your computer, and then restart the
computer.
l Check the cable connector for bent or broken pins and for damaged or frayed cables. Straighten bent pins.
l Remove keyboard extension cables and connect the keyboard directly to the computer.
Test the keyboard — Connect a properly working keyboard to the computer, and try using the keyboard. If the new keyboard works, the original keyboard is faulty.
Run the Dell Diagnostics — See Dell Diagnostics.
Check for software and hardware conflicts — See Resolving Software and Hardware Incompatibilities.
Check the cable connections — Ensure that the card fan cable is connected firmly to the card fan connector on the system board (see System Board Components for mini tower computers, and System Board Components for desktop computers).
Check the Diagnostic Lights — See Diagnostic Lights.
Ensure that the power cable is firmly connected to the computer and to the electrical outlet
Turn the computer off — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Then restart your computer.

End the program —
Check the software documentation — If necessary, uninstall and then reinstall the program.
Turn the computer off — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Then restart your computer.
Check the software documentation or contact the software manufacturer for troubleshooting information —
l Ensure that the program is compatible with the operating system installed on your computer.
l Ensure that your computer meets the minimum hardware requirements needed to run the software. See the software documentation
for information.
l Ensure that the program is installed and configured properly.
l Verify that the device drivers do not conflict with the program.
l If necessary, uninstall and then reinstall the program.
Back up your files immediately
Use a virus-scanning program to check the hard drive, floppy disks, or CDs
Save and close any open files or programs and shut down your computer through the Start menu
Run the Dell Diagnostics — If all tests run successfully, the error condition is related to a software problem (see Dell Diagnostics).
No drive letter is assigned —
When Microsoft Windows XP detects the media card reader, the device is automatically assigned a drive letter as the next logical drive after all other physical drives in the system. If the next logical drive after the physical drives is mapped to a network drive, Windows XP does not automatically assign a drive letter to the media card reader.
To manually assign a drive for the media card reader:

FlexBay device is Disabled —
There is a FlexBay disable option in the BIOS setup that appears only when the FlexBay device is installed. If the FlexBay device is physically installed, but it is not running, check to see if it is enabled in the BIOS setup.
Fill out the Diagnostics Checklist as you complete these checks.
If you receive an insufficient memory message —
l Save and close any open files and exit any open programs you are not using to see if that resolves the problem.
l See the software documentation for minimum memory requirements. If necessary, install additional memory.
l Reseat the memory modules to ensure that your computer is successfully communicating with the memory.
l Run the Dell Diagnostics (see Dell Diagnostics).
If you experience other memory problems —
l Reseat the memory modules to ensure that your computer is successfully communicating with the memory.
l Ensure that you are following the memory installation guidelines.
l Run the Dell Diagnostics (see Dell Diagnostics).
Check the mouse cable —
Restart the computer —
Test the mouse — Connect a properly working mouse to the computer, and try using the mouse. If the new mouse works, the original mouse is faulty.
Check the mouse settings —
If you are using a PS/2 mouse

Reinstall the mouse driver — See Reinstalling Drivers and Utilities.
Run the Dell Diagnostics —
l See Dell Diagnostics.
Check for software and hardware conflicts —
l See Resolving Software and Hardware Incompatibilities.
Fill out the Diagnostics Checklist as you complete these checks.
Check the network cable connector — Ensure that the network cable is firmly inserted into both the network connector on the back of the computer and the network jack.
Check the network lights on the front or back of the computer depending on system chassis type. — No connection speed light indicates that no network communication exists. Replace the network cable.
Restart the computer and log on to the network again
Check your network settings — Contact your network administrator or the person who set up your network to verify that your network settings are correct and that the network is functioning.
Check for software and hardware conflicts —
l See Resolving Software and Hardware Incompatibilities.
Fill out the Diagnostics Checklist as you complete these checks.
If the power light is green and the computer is not responding — See Diagnostic Lights
If the power light is blinking green — The computer is in standby mode. Press a key on the keyboard or move the mouse to resume normal operation.
If the power light is off — The computer is either turned off or is not receiving power.
l Reseat the power cable into both the power connector on the back of the computer and the electrical outlet.
l If the computer is plugged into a power strip, ensure that the power strip is plugged into an electrical outlet and that the power strip
is turned on. Also bypass power protection devices, power strips, and power extension cables to verify that the computer turns on

properly.
l Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
l Ensure that the main power cable and front panel cable are securely connected to the system board.
If the power light is amber and green or steady amber — A device might be malfunctioning or incorrectly installed.
l Remove and then reinstall the memory modules (see Memory).
l Remove and then reinstall any cards.
l Remove and then reinstall the graphics card, if applicable.
If the power light is blinking amber —
The computer is receiving electrical power, but an internal power problem might exist.
l Ensure that the voltage selection switch is set to match the AC power at your location (if applicable).
l Ensure that the processor power cable is securely connected to the system board.
Eliminate interference — Some possible causes of interference are:
l Power, keyboard, and mouse extension cables
l Too many devices on a power strip
l Multiple power strips connected to the same electrical outlet
Fill out the Diagnostics Checklist as you complete these checks.
Check the printer documentation — See the printer documentation for setup and troubleshooting information.
Ensure that the printer is turned on
Check the printer cable connections —
l See the printer documentation for cable connection information.
l Ensure that the printer cables are securely connected to the printer and the computer.
Test the electrical outlet —
Ensure that the electrical outlet is working by testing it with another device, such as a lamp. —
Verify that the printer is recognized by Windows —
If the printer is listed, right-click the printer icon.
Reinstall the printer driver — See the printer documentation for instructions.

To restore the computer's system settings to their default values —
If you wait too long and the Microsoft® Windows® logo appears, continue to wait until you see the Windows desktop. Then shut down your computer through the Start menu and try again.
Fill out the Diagnostics Checklist as you complete these checks.
Check the option setting — See the device's documentation for the recommended settings. Then enter system setup (see System Setup) and ensure that the Serial Port #1 setting (or the Serial Port #2 settings if you have an optional serial port adapter installed) or the LPT Port Mode setting matches the recommended settings.
Run the Dell Diagnostics — See Dell Diagnostics.
Fill out the Diagnostics Checklist as you complete these checks.
Check the speaker cable connections — Ensure that the speakers are connected as shown on the setup diagram supplied with the speakers. If you purchased an audio card, ensure that the speakers are connected to the card.
Ensure that the subwoofer and the speakers are turned on — See the setup diagram supplied with the speakers. If your speakers have volume controls, adjust the volume, bass, or treble to eliminate distortion.
Adjust the Windows volume control — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted.
Disconnect headphones from the headphone connector — Sound from the speakers is automatically disabled when headphones are connected to the computer's front-panel headphone connector.
Test the electrical outlet — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
Enable digital mode — Your speakers do not work if the CD drive is operating in analog mode.

Eliminate possible interference — Turn off nearby fans, fluorescent lights, or halogen lamps to check for interference.
Run the speaker diagnostics
Reinstall the audio driver — See Drivers.
Check the device option setting — Enter system setup (see System Setup) and ensure that the Audio Controller option is set to On. Exit system setup and restart your computer.
Run the Dell Diagnostics — See Dell Diagnostics.
Check for software and hardware conflicts — See Resolving Software and Hardware Incompatibilities.
Check the headphone cable connection — Ensure that the headphone cable is securely inserted into the headphone connector.
Disable digital mode — Your headphones do not work if the CD drive is operating in digital mode.
Adjust the Windows volume control — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted.
Fill out the Diagnostics Checklist as you complete these checks.
Check the monitor cable connection —
l If you purchased a graphics card, ensure that the monitor is connected to the card.
l Ensure that your monitor is properly connected (see the Quick Reference Guide that came with your computer).
l If you are using a video extension cable and removing the cable solves the problem, the cable is defective.
l Swap the computer and monitor power cables to determine if the power cable is defective.
l Check the connector for bent or broken pins. (It is normal for monitor cable connectors to have missing pins.)
Check the monitor power light — If the power light is off, firmly press the button to ensure that the monitor is turned on. If the power light is lit or blinking, the monitor has power. If the power light is blinking, press a key on the keyboard or move the mouse.

Test the electrical outlet — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
Test the monitor — Connect a properly working monitor to the computer, and try using the monitor. If the new monitor works, the original monitor is faulty.
Check the diagnostic lights — See Diagnostic Lights.
Check the card setting — Enter system setup (see System Setup) and ensure that Primary Video option is set correctly. Exit system setup and restart your computer.
Run the monitor self-test — Check the monitor documentation for more information.
Check the monitor settings — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing (degaussing) the monitor, and running the monitor self-test.
Move the subwoofer away from the monitor — If your speaker system includes a subwoofer, ensure that the subwoofer is at least 60 cm (2 ft) away from the monitor.
Move the monitor away from external power sources — Fans, fluorescent lights, halogen lamps, and other electrical devices can cause the screen image to appear "shaky." Turn off nearby devices to check for interference.
Adjust the Windows display settings —

Removing the Chassis Intrusion Switch
Replacing the Chassis Intrusion Switch
Resetting the Chassis Intrusion Detector




If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Then shut down your computer and try again.



Removing the System Board: Mini Tower, Desktop, and Small Form Factor Computers
l Mini Tower System Board Screws
l Desktop System Board Screws
l Small Form Factor System Board Screws

1 mini tower system board 2 screws (8)


1 desktop system board 2 screws (8)

1 small form factor system board 2 screws (6)
Place the system board assembly that you just removed next to the replacement system board to ensure it is identical.



Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, OptiPlex, Inspiron, Dimension, Latitude, Dell Precision, DellNet, TravelLite, Dell OpenManage, PowerVault, Axim, PowerEdge, PowerConnect, and PowerApp are trademarks of Dell Inc.; AMD, AMD Athlon, AMD Phenom, and combinations thereof, and Cool 'n' Quiet are trademarks of Advanced Micro Devices, Inc; Microsoft and Windows are registered trademarks of Microsoft Corporation; IBM is a registered trademark of International Business Machines Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
March 2008 RP699 Rev. A03

About Your Mini Tower Computer
Front View

1 optical drive (optional)
Insert media (if supported) into this drive.
2 Flexbay drive Can contain an optional floppy drive or an optional media card reader.
3 USB 2.0 connectors (2)
Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see System Setup for more information on booting to a USB device).
It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
4 LAN indicator light
This light indicates that a local area network (LAN) connection is established.
Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see Diagnostic Lights.
6 power button Press this button to turn on the computer.
7 power light The power light illuminates and blinks or remains solid to indicate different operating modes:
l No light — The computer is turned off.
l Steady green — The computer is in a normal operating state.
l Blinking green — The computer is in a power-saving mode.
Inside Your Computer · 5 diagnostic lights


l Blinking or solid amber — See Power Problems.
To exit from a power-saving mode, press the power button or use the keyboard or the mouse if it is configured as a wake device in the Windows Device Manager. For more information about sleep modes and exiting from a power-saving mode, see Power Management.
See System Lights for a description of light codes that can help you troubleshoot problems with your computer.
This light flickers when the hard drive is being accessed.
Use the headphone connector to attach headphones and most kinds of speakers.

1 cover release latch
This latch allows you to open the computer cover.
2 padlock ring Insert a padlock to lock the computer cover.
3 voltage selection switch
Your computer is equipped with a manual voltage-selection switch.
To help avoid damaging a computer with a manual voltage selection switch, set the switch for the voltage that most closely matches the AC power available in your location.
Also, ensure that your monitor and attached devices are electrically rated to operate with the AC power available in your location.
Insert the power cable.
Plug serial, USB, and other devices into the appropriate connectors. See Back-Panel Connectors.
6 card slots Access connectors for any installed PCI and PCI Express cards.
4 power connector · 5 back-panel connectors


Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.
2 link integrity light
l Green — A good connection exists between a 10-Mbps network and
the computer.
l Orange — A good connection exists between a 100-Mbps network
and the computer.
l Yellow — A good connection exists between a 1-Gbps (or 1000-
Mbps) network and the computer.
l Off — The computer is not detecting a physical connection to the
network.
3 network adapter connector
To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached.
On computers with a network connector card, use the connector on the card.
It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.
4 network activity light
Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.
Use the green line-out connector to attach headphones and most speakers with integrated amplifiers.
On computers with a sound card, use the connector on the card.
Use the line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR.
On computers with a sound card, use the connector on the card.
7 USB 2.0 connectors (5)
Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
Plug the cable from your VGA-compatible monitor into the blue connector.
Connect a serial device, such as a handheld device, to the serial port. The default designations are COM1 for serial connector 1 and COM2 for serial connector 2.
For more information, see System Setup Options.


1 optical drive 2 floppy drive 3 power supply
4 chassis intrusion switch (optional) 5 system board 6 heat sink assembly


2 processor socket (CPU) 3 memory module connectors (DIMM_1, DIMM_2, DIMM_3, DIMM_4)
7 front-panel connector 8 power connector 9 intrusion switch connector
7 hard drive



Resolving Software and Hardware Incompatibilities
If you experience a problem with your computer, perform the checks in this section and run the Dell Diagnostics before you contact Dell (see Contacting Dell) for technical assistance.
It is recommended that you print these procedures before you begin.
Enter system setup, review your computer's configuration information, and ensure that the device you want to test displays in system setup and is active (see Entering System Setup).
Start the Dell Diagnostics from either your hard drive or from the Drivers and Utilities media.
The Dell Diagnostics is located on a hidden diagnostic utility partition on your hard drive.
If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Then shut down your computer and try again.
When the DELL™ logo appears, press immediately.
If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop. Then shut down your computer and try again.

3. When the boot device list appears, highlight IDE CD-ROM Device and press . 4. Select the IDE CD-ROM Device option from the CD boot menu. 5. Select the Boot from CD-ROM option from the menu that appears. 6. Type 1 to start the Drivers and Utilities media menu. 7. Type 2 to start the Dell Diagnostics. 8. Select Run the 32 Bit Dell Diagnostics from the numbered list. If multiple versions are listed, select the version appropriate for your computer. 9. When the Dell Diagnostics Main Menu appears, select the test you want to run.

Express Test Performs a quick test of devices. This test typically takes 10 to 20 minutes and requires no interaction on your part. Run Express Test first to
Performs a thorough check of devices. This test typically takes an hour or more and requires you to answer questions periodically.
Custom Test Tests a specific device. You can customize the tests you want to run.
Lists the most common symptoms encountered and allows you to select a test based on the symptom of the problem you are having.
If you cannot resolve the error condition, contact Dell (see Contacting Dell).
Results Displays the results of the test and any error conditions encountered.
Errors Displays error conditions encountered, error codes, and the problem description.
Help Describes the test and may indicate requirements for running the test.
Configuration Displays your hardware configuration for the selected device.
The Dell Diagnostics obtains configuration information for all devices from system setup, memory, and various internal tests, and it displays the information in the device list in the left pane of the screen. The device list may not display the names of all the components installed on your computer or all devices attached to your computer.
Parameters Allows you to customize the test by changing the test settings.
Your power button light and hard-drive light may indicate a computer problem.

Solid green Power is on, and the computer is operating normally. On the desktop computer, a solid green light indicates a network connection.
Tab · Function

Blinking green The computer is in a power-saving mode (Microsoft® Windows® XP).
Press the power button, move the mouse, or press a key on the keyboard to wake the computer.
Blinks green several times and then turns off
A configuration error exists. Check the diagnostic lights to see if the specific problem is identified.
Solid yellow The Dell Diagnostics is running a test, or a device on the system board may be faulty or incorrectly installed.
If the Dell Diagnostics is running, allow the testing to complete.
If the computer does not boot, contact Dell for technical assistance.
Blinking yellow A power supply or system board failure has occurred. See Power Problems.
Solid green and a beep code during POST
A problem was detected while the BIOS was executing. See Beep Codes for instructions on diagnosing the beep code. Also, check the diagnostic lights to see if the specific problem is identified.
Solid green power light and no beep code and no video during POST
The monitor or the graphics card may be faulty or incorrectly installed.
Check the diagnostic lights to see if the specific problem is identified (see Video and Monitor Problems).
Solid green power light and no beep code but the computer locks up during POST
An integrated system board device may be faulty. Check the diagnostic lights to see if the specific problem is identified. If the problem is not identified, contact Dell for technical assistance.
To help you troubleshoot a problem, your computer has four lights labeled "1," "2," "3," and "4" on the front panel. The lights can be off or green. When the computer starts normally, the patterns or codes on the lights change as the boot process completes. If the POST portion of system boot completes successfully, all four lights display solid green. If the computer malfunctions during the POST process, the pattern displayed on the LEDs may help identify where in the process the computer halted.
The computer is in a normal off condition, or a possible pre-BIOS failure has occurred.
Plug the computer into a working electrical outlet and press the power button.
The diagnostic lights are not lit after the computer successfully boots to the operating system.
A possible BIOS failure has occurred; the computer is in the recovery mode.
Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer.
A possible processor failure has occurred. Reinstall the processor and restart the computer.
Memory modules are detected, but a memory failure has occurred.
l If you have one memory module installed, reinstall it and restart the computer (see
Memory for instructions on how to remove and install memory modules).
l If you have two or more memory modules installed, remove the modules, reinstall one
module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error.
l If available, install properly working memory of the same type into your computer.
l If the problem persists, contact Dell.
A possible graphics card failure has occurred.
l If the computer has a graphics card, remove the card, reinstall it, and then restart the
computer.
l If the problem still exists, install a graphics card that you know works and restart the
computer.
l If the problem persists or the computer has integrated graphics, contact Dell.
A possible floppy or hard drive failure has occurred.
Reseat all power and data cables and restart the computer.
A possible USB failure has occurred. Reinstall all USB devices, check cable connections, and then restart the computer.
No memory modules are detected. l If you have one memory module installed, reinstall it and restart the computer (see
Memory for instructions on how to remove and install memory modules).
l If you have two or more memory modules installed, remove the modules, reinstall one
module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error.
l If available, install properly working memory of the same type into your computer.
l If the problem persists, contact Dell.
Light Pattern · Problem Description · Suggested Resolution

Memory modules are detected, but a memory configuration or compatibility error exists.
l Ensure that no special memory module/memory connector placement requirements
exist (see Memory).
l Verify that the memory modules that you are installing are compatible with your
computer.
l If the problem persists, contact Dell.
A failure has occurred.
l Ensure that the cables are properly connected to the system board from the hard
drive, and optical drive.
l Check the computer message that appears on your monitor screen.
This pattern also displays when you enter system setup and may not indicate a problem (see Entering System Setup).
l If the problem persists, contact Dell.
After POST is complete, all four diagnostic lights turn green briefly before turning off to indicate normal operating condition.
None.
Your computer might emit a series of beeps during start-up if the monitor cannot display errors or problems. This series of beeps, called a beep code, identifies a problem. One possible beep code consists of one long beep and then two short beeps. This beep code tells you that the computer encountered a memory test failure.
If your computer beeps during start-up:

1 long, 2 short Memory test failure (bad memory during memory sizing)
Fill out the Diagnostics Checklist as you complete these checks (see Diagnostics Checklist).
If the message is not listed, see the documentation for the operating system or the program that was running when the message appeared.
A filename cannot contain any of the following characters: \ / : * ? " < > | — Do not use these characters in filenames.
A required .DLL file was not found — The program that you are trying to open is missing an essential file. To remove and then reinstall the program:
Alert! Previous attempts at booting this system have failed at checkpoint [nnnn]. For help in resolving this problem, please note this checkpoint and contact Dell Technical Support — Contact Dell (see Contacting Dell) and report the checkpoint code (nnnn) to the support technician.
Alert! Air temperature sensor not detected — For any computer type except the ultra small form factor computer, ensure that all cables are securely fastened to the I/O panel and to the system board and reboot your computer. If this does not resolve the problem or if you have an ultra small form factor computer, contact Dell (see Contacting Dell).
Attachment failed to respond — See Drive Problems.

Bad command or file name — Ensure that you spelled the command correctly, put spaces in the proper place, and used the correct pathname.
Bad error-correction code (ECC) on disk read — See Drive Problems.
Controller has failed — See Drive Problems.
Data error — See Drive Problems.
Decreasing available memory —
See Lockups and Software Problems.
Diskette drive 0 seek failure — See Drive Problems.
Diskette read failure —
See Drive Problems.
Diskette subsystem reset failed — Run the Dell Diagnostics (see Dell Diagnostics).
Diskette write protected — Slide the write-protect notch on the floppy disk to the open position.
Drive not ready — Put a floppy disk in the drive.
Gate A20 failure —
See Lockups and Software Problems.
Hard-disk configuration error —
Hard-disk controller failure —
Hard-disk drive failure —
Hard-disk drive failure —
See Drive Problems.
Insert bootable media — Insert a bootable floppy disk or CD.
Invalid configuration information - please run SETUP program — Enter system setup and correct the computer configuration information (see Entering System Setup).
Keyboard failure — See Keyboard Problems.
Memory address line failure at address, read value expecting value — See Lockups and Software Problems.
Memory allocation error —

Memory data line failure at address, read value expecting value —
Memory double word logic failure at address, read value expecting value —
Memory odd/even logic failure at address, read value expecting value —
Memory write/read failure at address, read value expecting value —
Memory size in CMOS invalid —
See Lockups and Software Problems.
No boot device available —
l If the floppy drive is your boot device, ensure that a bootable floppy disk is in the drive.
l If the hard drive is your boot device, ensure that the cables are connected and that the drive is installed properly and partitioned as a
boot device.
l Enter system setup and ensure that the boot sequence information is correct (see Entering System Setup).
No boot sector on hard-disk drive — Enter system setup and ensure that the computer configuration information for the hard drive is correct (see Entering System Setup).
No timer tick interrupt — Run the Dell Diagnostics (see Dell Diagnostics).
Non-system disk or disk error — Replace the floppy disk with one that has a bootable operating system or remove the floppy disk from drive A and restart the computer.
Not a boot diskette — Insert a bootable floppy disk and restart your computer.
Not enough memory or resources. Close some programs and try again — Close all windows and open the program that you want to use. In some cases, you might have to restart your computer to restore computer resources. If so, run the program that you want to use first.
Operating system not found — Contact Dell (see Contacting Dell).
Plug and Play Configuration Error —
Requested sector not found —
See Drive Problems.
Sector not found —
l Run the Windows error-checking utility to check the file structure on the floppy disk or hard drive. See Windows Help for instructions.
l If a large number of sectors are defective, back up the data (if possible), and then reformat the floppy disk or hard drive.
Seek error — See Drive Problems.
Read fault — · Reset failed —

Shutdown failure — Run the Dell Diagnostics (see Dell Diagnostics).
Time-of-day clock stopped —
Time-of-day not set-please run the System Setup program —
Enter system setup (see Entering System Setup) and correct the date or time. If the problem persists, replace the battery (see Replacing the Battery).
Timer chip counter 2 failed — Run the Dell Diagnostics (see Dell Diagnostics).
Unexpected interrupt in protected mode — Run the Dell Diagnostics (see Dell Diagnostics).
If no replacement drive is immediately available and the drive is not the only bootable drive, enter system setup (see Entering System Setup) and change the appropriate drive setting to None. Then remove the drive from the computer.
Write fault on selected drive —
See Drive Problems.
<drive letter>:\ is not accessible. The device is not ready — The selected drive cannot read its medium. Depending on its medium type, insert a floppy, CD, DVD, or Zip disk into the drive and try again.
If a device is either not detected during the operating system setup or is detected but incorrectly configured, you can use Device Manager or the Hardware Troubleshooter to resolve the incompatibility.
To resolve incompatibilities using Device Manager:
Incorrectly configured devices are indicated by a yellow exclamation point [!] or a red X if the device has been disabled.
The Device status area in the Properties window reports the devices that need to be re-configured.
To resolve incompatibilities using the Windows XP Hardware Troubleshooter:
Write fault —


Dell Inc. ("Dell") manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry-standard practices. For information about the Dell warranty for your computer, see the Product Information Guide or separate paper warranty document that shipped with your computer.
Pages referenced in this manual — manufacturer, support and downloads.
What the fault codes shown on the display mean and how to clear them.
| Code | Meaning | Fix | |
|---|---|---|---|
| 1 short | F12 key pressed | p.212 |
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| The computer is in a normal off condition, or a possible pre-BIOS failure has occurred. The diagnostic lights are not lit after the computer successfully boots to the operating system. | Plug the computer into a working electrical outlet and press the power button. | p.211 | |
| A possible BIOS failure has occurred; the computer is in the recovery mode. | Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer. | p.211 | |
| A possible processor failure has occurred. | Reinstall the processor and restart the computer. | p.211 | |
| Memory modules are detected, but a memory failure has occurred. | l If you have one memory module installed, reinstall it and restart the computer (see Memory for instructions on how to remove and install memory modules). l If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error. l If available, install properly working memory of the same type into your computer. l If the problem persists, contact Dell. | p.211 | |
| A possible graphics card failure has occurred. | l If the computer has a graphics card, remove the card, reinstall it, and then restart the computer. l If the problem still exists, install a graphics card that you know works and restart the computer. l If the problem persists or the computer has integrated graphics, contact Dell. | p.211 | |
| A possible floppy or hard drive failure has occurred. | Reseat all power and data cables and restart the computer. | p.211 | |
| A possible USB failure has occurred. | Reinstall all USB devices, check cable connections, and then restart the computer. | p.211 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.