EN
Dell logo
Official user manual

Dell DCDO

252 pages·5.3 MB·Fan·PDF·ENDEITNLJA
Dell DCDO
Table of Contents 27 sections Quick Reference Guide · Contents · Finding Information · Setting Up Your Computer · … ShowHide
Page 1 of the Dell DCDO user manual — Dell Precision™ T7400 Quick Reference Guide
Page 1 · click to enlarge
Page 1

Dell Precision™ T7400 Quick Reference Guide

w w w. d e l l . c o m | s u p p o r t . d e l l . c o m

Model DCDO

Page 2 of the Dell DCDO user manual — CAUTION: A CAUTION indicates a potential for property damage, personal injury,
Page 2 · click to enlarge
Page 2

Notes, Notices, and Cautions

your computer.

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

Information in this document is subject to change without notice. © 2007 Dell Inc. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and Dell Precision are trademarks of Dell Inc.; Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

September 2007 P/N YT561 Rev. A00

Model DCDO

Page 5 of the Dell DCDO user manual — Finding Information
Page 5 · click to enlarge
Page 5

Finding Information

computer. Some features or media may not be available in certain countries.

What Are You Looking For? Find It Here

  • A diagnostic program for my computer

Drivers and Utilities Disc

  • Drivers for my computer
  • My device documentation

Documentation and drivers are already installed on your computer. You can use the Drivers and Utilities disc to reinstall drivers (see "Reinstalling Drivers and Utilities" in your User’s Guide) and to run the Dell™ Diagnostics (see "Dell Diagnostics" on page 33).

  • Desktop System Software (DSS)
Dell DCDO — Finding Information diagram (page 5)
Fig. 1 · Finding Information

Dell Precision™ User’s Guide

  • How to remove and replace parts
  • Specifications

Microsoft® Windows® XP and Microsoft Windows Vista™ Help and Support Center

  • How to configure system settings

1 Click Start→ Help and Support→ Dell User and System Guides→ System Guides.

  • How to troubleshoot and solve problems

2 Click the User’s Guide for your computer.

Page 6 of the Dell DCDO user manual — Finding Information
Page 6 · click to enlarge
Page 6

What Are You Looking For? Find It Here

  • Warranty information

Dell™ Product Information Guide

  • Terms and Conditions (U.S. only)
Dell DCDO — Finding Information diagram (page 6)
Fig. 2 · Finding Information
  • Safety instructions
  • Regulatory information
  • Ergonomics information
  • End User License Agreement
  • Service Tag and Express Service Code

Service Tag and Microsoft Windows Product Key

  • Microsoft ® Windows ® Product Key

These labels are located on your computer:

  • Use the Service Tag to identify your computer when you use support.<a href="http://dell.com" rel="nofollow noopener" target="_blank">dell.com</a> or contact Dell support.
  • Enter the Express Service Code to direct your call when contacting Dell support.
Dell DCDO — Finding Information diagram (page 6)
Fig. 3 · Finding Information
Page 7 of the Dell DCDO user manual — Finding Information
Page 7 · click to enlarge
Page 7

What Are You Looking For? Find It Here

  • Solutions — Troubleshooting hints and tips, articles from technicians, online courses, and frequently asked questions

Dell Support Website — support.dell.com

  • Community — Online discussion with other Dell customers
  • Upgrades — Upgrade information for components, such as the memory, hard drive, and operating system
  • Customer Care — Contact information, service call and order status, and warranty and repair information
  • Service and support — Service call status, support history, service contract, and online discussions with support
  • Dell Technical Update Service — Proactive e-mail notification of software and hardware updates for your computer
  • Reference — Computer documentation, details on my computer configuration, product specifications, and white papers
  • Downloads — Certified drivers, patches, and software updates
  • Desktop System Software (DSS) — If you reinstall the operating system for your computer, you should also reinstall the DSS utility. DSS automatically detects your computer and operating system and installs the updates appropriate for your configuration, providing critical updates for your operating system and support for processors, optical drives, USB devices, for example. DSS is necessary for correct operation of your Dell computer.

To download Desktop System Software:

1 Go to support.dell.com, select your country/region, and then click Drivers & Downloads.

2 Click Select Model or Enter a Tag, make the appropriate selections or enter the appropriate information for your computer, and then click Confirm.

3 Scroll down to System and Configuration Utilities→ Desktop System Software, and then click Download Now.

Page 8 of the Dell DCDO user manual — Finding Information
Page 8 · click to enlarge
Page 8

What Are You Looking For? Find It Here

  • How to use Windows XP

Windows Help and Support Center

1 Click Start→ Help and Support.

  • How to use Windows Vista

2 Type a word or phrase that describes your problem and click the arrow icon.

  • How to work with programs and files
  • How to personalize my desktop

3 Click the topic that describes your problem.

4 Follow the instructions on the screen.

  • How to reinstall my operating system Operating System Disc

The operating system is already installed on your computer. To reinstall your operating system, use the Operating System disc that came with your computer (see "Restoring Your Operating System" in your User’s Guide).

Dell DCDO — Finding Information diagram (page 8)
Fig. 4 · Finding Information

After you reinstall your operating system, use the optional Drivers and Utilities disc to reinstall drivers for the devices that came with your computer.

Your operating system product key label is located on your computer.

Page 9 of the Dell DCDO user manual — Switching From Tower to Desktop Orientation
Page 9 · click to enlarge
Page 9

What Are You Looking For? Find It Here

  • How to use Linux

Dell Supported Linux Sites

  • E-mail discussions with users of Dell Precision products and the Linux operating system
  • linux.<a href="http://dell.com" rel="nofollow noopener" target="_blank">dell.com</a>
  • <a href="http://lists.us" rel="nofollow noopener" target="_blank">lists.us</a>.<a href="http://dell.com/mailman/listinfo/linuxprecision" rel="nofollow noopener" target="_blank">dell.com/mailman/listinfo/linuxprecision</a>
  • Additional information regarding Linux and my Dell Precision computer

Setting Up Your Computer

Changing Between Tower and Desktop Orientations

must use an optional kit available from Dell. See "Product Information" in your User’s Guide for more details on ordering from Dell.

the desktop computer.

1 Follow the procedures in "Before You Begin" in your User’s Guide.

2 Remove the computer cover (see "Removing the Computer Cover" in your User’s Guide).

3 Remove the front panel (see "Removing the Front Panel" in your User’s Guide).

4 Remove the drive panel and prepare the drive panel by adding or removing inserts, as needed (see "Drive Panels" in your User’s Guide).

Switching From Tower to Desktop Orientation

1 Remove all installed floppy drives or media card readers by following the steps in "Removing a Floppy Drive or Media Card Reader (Tower Computer)" in your User’s Guide, and then reinstall a single floppy drive or media card reader by following the steps in "Installing a Floppy Drive or Media Card Reader (Desktop Computer)" in your User’s Guide.

2 Remove all installed optical drives by following the steps in "Removing an Optical Drive (Tower Computer)" in your User’s Guide, and then reinstall the drives by following the steps in "Installing an Optical Drive (Desktop Computer)" in your User’s Guide.

Page 10 of the Dell DCDO user manual — Installing Your Computer in an Enclosure
Page 10 · click to enlarge
Page 10

Switching From Desktop to Tower Orientation

1 Remove the floppy drive or media card reader (if installed) by following the steps in "Removing a Floppy Drive or a Media Card Reader (Desktop Computer)" in your User’s Guide, and then reinstall the floppy drive or media card reader by following the steps in "Installing a Floppy Drive or Media Card Reader (Tower Computer)" in your User’s Guide.

2 Remove all installed optical drives by following the steps in "Removing an Optical Drive (Desktop Computer)" in your User’s Guide, and reinstall the drives by following the steps in "Installing an Optical Drive (Tower Computer)" in your User’s Guide.

Installing Your Computer in an Enclosure

Installing your computer in an enclosure can restrict airflow, can cause your computer to overheat, and may impact your computer’s performance. Follow the guidelines below when installing your computer in an enclosure.

ambient operating temperature. The ambient room temperature must be a consideration when installing your computer in an enclosure. For details about your computer’s specifications, see "Specifications" in your User’s Guide.

Page 11 of the Dell DCDO user manual — Installing Your Computer in an Enclosure
Page 11 · click to enlarge
Page 11
  • Leave 10.2 cm (4 in) minimum clearance on all vented sides of the computer to permit the airflow required for proper ventilation.
Dell DCDO — Installing Your Computer in an Enclosure diagram (page 11)
Fig. 5 · Installing Your Computer in an Enclosure
  • If your computer is installed in a corner on or under a desk, leave 5.1 cm (2 in) minimum clearance from the back of the computer to the wall to permit the airflow required for proper ventilation.
  • If your enclosure has doors, ensure that they allow at least 30 percent airflow through the enclosure (front and back).
Page 12 of the Dell DCDO user manual — Installing Your Computer in an Enclosure
Page 12 · click to enlarge
Page 12
  • Do not install your computer in an enclosure that does not allow airflow. Restricting the airflow can cause your computer to overheat and may impact your computer’s performance .
Dell DCDO — Installing Your Computer in an Enclosure diagram (page 12)
Fig. 6 · Installing Your Computer in an Enclosure
Page 13 of the Dell DCDO user manual — Microsoft Windows XP
Page 13 · click to enlarge
Page 13

Transferring Information to a New Computer

You can use your operating system wizards to help you transfer files and other data from one computer to another computer.

Microsoft Windows XP

The Microsoft Windows XP operating system provides the Files and Settings Transfer Wizard to transfer data, such as:

  • E-mail messages
  • Toolbar settings
  • Window sizes
  • Internet bookmarks

You can transfer data from one computer to another computer over a network or serial connection, or by storing the data on removable media, such as a writable CD or DVD.

connecting a serial cable to the input/output (I/O) ports of the two computers. To transfer data over a serial connection, you must use the Network Connections utility in the Control Panel to perform additional configuration steps, such as setting up an advanced connection and designating the host computer and the guest computer.

For instructions on setting up a direct cable connection between two computers, see Microsoft Knowledge Base Article #305621, titled How to Set Up a Direct Cable Connection Between Two Computers in Windows XP. This information may not be available in certain countries.

Using the Files and Settings Transfer Wizard requires the Operating System disc that came with your computer or a wizard disk, which the wizard can create for you.

document #154781 (What Are The Different Methods To Transfer Files From My Old Computer To My New Dell™ Computer Using the Microsoft Windows XP Operating System?).

certain countries.

Page 14 of the Dell DCDO user manual — TRANSFER DATA TO THE DESTINATION COMPUTER —
Page 14 · click to enlarge
Page 14

Files and Settings Transfer Wizard (With the Operating System Disc)

which data is to be transferred as the old computer, and designates the destination computer to which the data is going to be transferred as the new computer.

PREPARE THE DESTINATION COMPUTER FOR THE FILE TRANSFER —

1 Click Start→ All Programs→ Accessories→ System Tools→ Files and Settings Transfer Wizard.

2 Under Which computer is this?, click New computer, and then click Next.

3 Under Do you have a Windows XP CD?, click I will use the wizard from the Windows XP CD, and then click Next.

4 Review the information under Now go to your old computer, and then go to the source computer. Do not click Next.

COPY DATA FROM THE SOURCE COMPUTER —

1 Insert the Windows XP Operating System disc into the source computer.

The Welcome to Microsoft Windows XP screen appears.

2 Click Perform additional tasks.

3 Under What do you want to do?, click Transfer files and settings.

The Files and Settings Transfer Wizard window appears.

4 Click Next.

5 Under Which computer is this?, click Old Computer, and then click Next.

6 Under Select a transfer method, click the transfer method of your choice, and then click Next.

7 Under What do you want to transfer?, click to select the data you want to transfer, and then click Next.

The selected data is copied and the Completing the Collection Phase screen appears.

8 Click Finish.

TRANSFER DATA TO THE DESTINATION COMPUTER —

1 Go to the destination computer.

2 Under Now go to your old computer, click Next.

Page 15 of the Dell DCDO user manual — COPY DATA FROM THE SOURCE COMPUTER —
Page 15 · click to enlarge
Page 15

3 Under Where are the files and settings?, click to select the method you chose for transferring your settings and files, and then click Next.

The wizard reads the collected files and settings and applies them to the destination computer. When the transfer is complete, the Finished screen appears.

4 Click Finished, and then restart the computer.

Files and Settings Transfer Wizard (Without the Operating System Disc)

To run the Files and Settings Transfer Wizard without the Operating System disc, you must create a wizard disk. The wizard disk allows you to create a backup image file on removable media.

which data is to be transferred as the old computer, and designates the destination computer to which the data is going to be transferred as the new computer.

CREATE A WIZARD DISK —

1 On the destination computer, click Start→ All Programs→ Accessories→ System Tools→ Files and Settings Transfer Wizard.

2 Under Which computer is this?, click New computer, and then click Next.

3 Under Do you have a Windows XP CD?, click I want to create a Wizard Disk in the following drive, and then click Next.

4 Insert a writable CD or DVD, and then click OK.

5 Review the information under Now go to your old computer, and then go to the source computer. Do not click Next.

COPY DATA FROM THE SOURCE COMPUTER —

1 Insert the wizard disk into the source computer.

2 Click Start→ Run.

3 Click Browse... and navigate to fastwiz on the wizard disk, and then click OK.

4 Under Which computer is this?, click Old Computer, and then click Next.

5 Under Select a transfer method, click the transfer method of your choice, and then click Next.

Page 16 of the Dell DCDO user manual — Power Protection Devices
Page 16 · click to enlarge
Page 16

6 Under What do you want to transfer?, click to select the data you want to transfer, and then click Next.

The selected data is copied and the Completing the Collection Phase screen appears.

7 Click Finish.

TRANSFER DATA TO THE DESTINATION COMPUTER —

1 Go to the destination computer.

2 Under Now go to your old computer, click Next.

3 Under Where are the files and settings?, click to select the method you chose for transferring your settings and files, and then click Next.

The wizard reads the collected files and settings and applies them to the destination computer. When the transfer is complete, the Finished screen appears.

4 Click Finished, and then restart the computer.

Microsoft Windows Vista

1 Click the Windows Vista Start button , and then click Transfer files and settings→ Start Windows Easy Transfer.

2 In the User Account Control dialog box, click Continue.

3 Click Start a new transfer or Continue a transfer in progress.

Follow the instructions provided on the screen by the Windows Easy Transfer wizard.

Power Protection Devices

Several devices are available to protect against power fluctuations and failures:

  • Surge protectors
  • Line conditioners
  • Uninterruptible power supplies (UPS)
Page 17 of the Dell DCDO user manual — Uninterruptible Power Supplies
Page 17 · click to enlarge
Page 17

Surge Protectors

Surge protectors and power strips equipped with surge protection help prevent damage to your computer from voltage spikes that can occur during electrical storms or after power interruptions. Some surge protector manufacturers include warranty coverage for certain types of damage. Carefully read the device warranty when choosing a surge protector and compare joule ratings to determine the relative effectiveness of different devices. A device with a higher joule rating offers more protection.

interruptions caused by nearby lightning strikes. When lightning occurs in your area, disconnect the telephone line from the telephone wall jack and disconnect your computer from the electrical outlet.

Many surge protectors have a telephone jack for modem protection. See the surge protector documentation for modem connection instructions.

network cable from the network wall jack during electrical storms.

Line Conditioners

Line conditioners are designed to maintain AC voltage at a fairly constant level.

Uninterruptible Power Supplies

data loss or file damage.

a UPS. Connect other devices, such as a printer, to a separate power strip that provides surge protection.

A UPS protects against power fluctuations and interruptions. UPS devices contain a battery that provides temporary power to connected devices when AC power is interrupted. The battery charges while AC power is available. See the UPS manufacturer documentation for information on battery operating time and to ensure that the device is approved by Underwriters Laboratories (UL).

Page 18 of the Dell DCDO user manual — Front View (Tower Orientation)
Page 18 · click to enlarge
Page 18

About Your Computer

Front View (Tower Orientation)

Dell DCDO — Front View (Tower Orientation) diagram (page 18)
Fig. 7 · Front View (Tower Orientation)

1–3 5.25-inch drive bays

Can hold a CD/DVD drive, or a media card reader, floppy drive, or a SATA hard drive in a 5.25-inch drive bay carrier. The hard-drive carrier is only for use in the 5.25-inch drive bays. The floppy-drive/media card reader and hard-drive carriers are not interchangeable.

Page 19 of the Dell DCDO user manual — About Your Computer
Page 19 · click to enlarge
Page 19

4 5.25-inch drive bay with special 3.5-inch drive panel plate

Can hold a CD/DVD drive, or a media card reader, a floppy drive, or a SATA hard drive in a 5.25-inch drive bay carrier. The drive-panel plate shown here is only for use with a floppy drive or media card reader; you can install the plate in front of any of the four 5.25-inch drive bays. For more information, see "Drive Panels" in your User’s Guide. The hard-drive carrier is only for use in the 5.25-inch drive bays. The floppy-drive/media card reader and hard-drive carriers are not interchangeable.

5 hard-drive activity light

The hard drive light is on when the computer reads data from or writes data to the hard drive. The light might also be on when a device such as your CD drive is operating.

6 IEEE 1394 connector

Use the IEEE 1394 connector for high-speed data devices such as digital video cameras and external storage devices.

7 USB 2.0 connectors (2)

Use the front USB connectors for devices that you connect occasionally, such as flash memory keys, cameras, or bootable USB devices. Dell recommends that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

8 power button, power light

Press the power button to turn on the computer. The light in the center of this button indicates the power state. For more information, see "Controls and Lights" in your User’s Guide. NOTE: To avoid losing data, do not use the power button to turn off the computer. Instead, perform an operating system shutdown.

9 Dell badge You can rotate the Dell badge so that "Dell" is read horizontally, depending on whether you use the desktop or tower orientation.

Use the headphone connector to attach headphones.

Use the microphone connector to attach a personal computer microphone for voice or musical input into a sound or telephony program.

12 diagnostic lights (4)

Use these lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see "Diagnostic Lights" in your User’s Guide.

13 network link light The network link light is on when a good connection exists between a 10-Mbps, 100-Mbps, or 1000-Mbps (or 1-Gbps) network and the computer.

10 headphone connector · 11 microphone connector

Page 20 of the Dell DCDO user manual — Back View (Tower Orientation)
Page 20 · click to enlarge
Page 20

Back View (Tower Orientation)

Dell DCDO — Back View (Tower Orientation) diagram (page 20)
Fig. 8 · Back View (Tower Orientation)

1 power connector Connect the power cable.

2 card slots Slots 2–6 support full-length cards, including one PCI, two PCI Express 2.0 x16, and two PCI-X slots. Slots 1 and 7 support half-length cards, including one PCI Express x8 (wired as x4) and one PCI-X slot.

3 back panel connectors

Plug USB, audio, and other devices into the appropriate connector (see "Back Panel Connectors" on page 21 for more information).

can cause serious thermal problems.

Page 21 of the Dell DCDO user manual — Back Panel Connectors
Page 21 · click to enlarge
Page 21

Back Panel Connectors

1 2 3 4 5 6 7 8

Dell DCDO — Back Panel Connectors diagram (page 21)
Fig. 9 · Back Panel Connectors

1 parallel connector Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.

2 mouse connector Plug a standard PS/2 mouse into the green mouse connector. Turn off the computer and any attached devices before you connect a mouse to the computer. If you have a USB mouse, plug it into a USB connector.

3 IEEE 1394 connector

Use the IEEE 1394 connector for high-speed data devices such as digital video cameras and external storage devices.

4 line-in connector Use the blue line-in connector to attach a playback device such as an MP3 player, CD drive, or VCR. On computers with a sound card, use the connector on the card.

5 line-out connector Use the green line-out connector to attach headphones and most speakers with integrated amplifiers. On computers with a sound card, use the connector on the card.

11 10 9

Page 22 of the Dell DCDO user manual — Back Panel Connectors
Page 22 · click to enlarge
Page 22

6 link integrity light Green — A good connection exists between a 10-Mbps network and the computer. Orange — A good connection exists between a 100-Mbps network and the computer. Yellow — A good connection exists between a 1000-Mbps (or 1-Gbps) network and the computer. Off — The computer is not detecting a physical connection to the network.

7 network adapter connector

To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on your computer. A click indicates that the network cable has been securely attached. Do not plug a telephone cable into the network connector. On computers with an additional network connector card, use the connectors on the card and on the back of the computer when setting up multiple network connections (such as a separate intra- and extranet). It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.

8 network activity light

Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.

9 USB 2.0 connectors (5)

It is recommended that you use the front USB connectors for devices that you connect occasionally, such as flash memory keys, cameras, or bootable USB devices. Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

If you have a standard PS/2 keyboard, plug it into the purple keyboard connector. If you have a USB keyboard, plug it into a USB connector.

11 serial connectors (2)

Connect a serial device, such as a handheld device, to the serial port. If necessary, the address for this port can be modified through the system setup program (see "System Setup" in you User’s Guide).

10 keyboard connector

Page 23 of the Dell DCDO user manual — Mouse (Non-Optical)
Page 23 · click to enlarge
Page 23

Cleaning Your Computer

Computer, Keyboard, and Monitor

CAUTION: Before you clean your computer, disconnect the computer from the

electrical outlet. Clean your computer with a soft cloth dampened with water. Do not use liquid or aerosol cleaners, which may contain flammable substances.

  • Use a vacuum cleaner with a brush attachment to gently remove dust from the slots and holes on your computer and from between the keys on the keyboard.

may damage the antiglare coating.

  • To clean your monitor screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the monitor’s antistatic coating.
  • Wipe the keyboard, computer, and plastic part of the monitor with a soft cleaning cloth moistened with water.

Do not soak the cloth or let water drip inside your computer or keyboard.

Mouse (Non-Optical)

1 Turn the retainer ring on the underside of your mouse counterclockwise, and then remove the ball.

2 Wipe the ball with a clean, lint-free cloth.

3 Blow carefully into the ball cage to dislodge dust and lint.

4 Clean the rollers inside the ball cage with a cotton swab moistened lightly with isopropyl alcohol.

5 Recenter the rollers in their channels, as needed. Ensure that fluff from the swab is not left on the rollers.

6 Replace the ball and retainer ring, and then turn the retainer ring clockwise until it clicks into place.

Page 24 of the Dell DCDO user manual — Power Lights
Page 24 · click to enlarge
Page 24

Floppy Drive

misaligned and prevent the drive from operating.

Clean your floppy drive using a commercially available cleaning kit. These kits contain pretreated floppy disks to remove contaminants that accumulate during normal operation.

CDs and DVDs

follow the instructions that come with the compressed air. Never touch the lens in the drive.

1 Hold the disc by its outer edge. You can also touch the inside edge of the center hole.

the disc.

2 With a soft, lint-free cloth, gently wipe the bottom of the disc (the unlabeled side) in a straight line from the center to the outer edge of the disc.

For stubborn dirt, try using water or a diluted solution of water and mild soap. You can also purchase commercial products that clean discs and provide some protection from dust, fingerprints, and scratches. Cleaning products for CDs are safe to use on DVDs.

Troubleshooting Tools

Power Lights

The power button light located on the front of the computer illuminates and blinks or remains solid to indicate different states:

  • If the power light is green and the computer is not responding, "Diagnostic Lights" on page 26.
  • If the power light is blinking green, the computer is in standby mode. Press a key on the keyboard, move the mouse, or press the power button to resume normal operation.
Page 25 of the Dell DCDO user manual — Floppy Drive
Page 25 · click to enlarge
Page 25
  • If the power light is off, the computer is either turned off or is not receiving power.

– Reseat the power cable into both the power connector on the back of the computer and the electrical outlet.

– If the computer is plugged into a power strip, ensure that the power strip is plugged into an electrical outlet and that the power strip is turned on.

– Bypass power protection devices, power strips, and power extension cables to verify that the computer turns on properly.

– Ensure that the electrical outlet is working by testing it with another device, such as a lamp.

– Ensure that the main power cable and front panel cable are securely connected to the system board (see "System Board Components" in your User’s Guide).

  • If the power light is blinking amber, the computer is receiving electrical power, but an internal power problem might exist.

– Ensure that the voltage selection switch is set to match the AC power at your location, if applicable.

– Ensure that the processor power cable is securely connected to the system board (see "System Board Components" in your User’s Guide).

  • If the power light is steady amber, a device may be malfunctioning or incorrectly installed.

– Remove and then reinstall the memory modules (see "Removing the Front Panel" in your User’s Guide).

– Remove and then reinstall any cards (see "Cards" in your User’s Guide).

  • Eliminate interference. Some possible causes of interference are:

– Power, keyboard, and mouse extension cables

– Too many devices on a power strip

– Multiple power strips connected to the same electrical outlet

Page 26 of the Dell DCDO user manual — Diagnostic Light Codes During POST
Page 26 · click to enlarge
Page 26

Diagnostic Lights

To help troubleshoot a problem, your computer has four lights labeled 1, 2, 3, and 4 on the front panel (see "Front View (Tower Orientation)" on page 18). When the computer starts normally, the lights flash, and then turn off. If the computer malfunctions, use the sequence of the lights to help identify the problem.

the operating system.

Diagnostic Light Codes During POST

Light Pattern Problem Description Suggested Resolution

The computer is in a normal off condition or a possible pre-BIOS failure has occurred.

Plug the computer into a working electrical outlet and press the power button.

A possible BIOS failure has occurred; the computer is in the recovery mode.

  • Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer.
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

A possible processor failure has occurred.

  • Reseat the processor (see "Processor" in your User’s Guide ).
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).
Page 27 of the Dell DCDO user manual — Diagnostic Lights
Page 27 · click to enlarge
Page 27

Light Pattern Problem Description Suggested Resolution

Memory modules are detected, but a memory failure has occurred.

  • If two or more memory modules are installed, remove the modules (see "Memory" in your User’s Guide ), reinstall one module, and then restart the computer. If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error.
  • If available, install working memory of the same type into your computer (see "Memory" in your User’s Guide ).
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

A possible graphics card failure has occurred.

  • Reseat any installed graphics cards (see "Cards" in your User’s Guide ).
  • If available, install a working graphics card into your computer.
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

A possible floppy or hard drive failure has occurred.

  • Reseat all power and data cables and restart the computer.
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

A possible USB failure has occurred.

  • Reinstall all USB devices, check cable connections, and then restart the computer.
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).
Page 28 of the Dell DCDO user manual — Diagnostic Lights
Page 28 · click to enlarge
Page 28

Light Pattern Problem Description Suggested Resolution

No memory modules are detected.

  • If two or more memory modules are installed, remove the modules (see "Memory" in your User’s Guide ), reinstall one module, and then restart the computer. If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error.
  • If available, install working memory of the same type into your computer (see "Memory" in your User’s Guide ).
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

System board failure has occurred.

Contact Dell (see "Contacting Dell" in your User’s Guide).

Memory modules are detected, but a memory configuration or compatibility error exists.

  • Ensure that no special requirements for memory module/connector placement exist (see "Memory" in your User’s Guide ).
  • Ensure that the memory you are using is supported by your computer (see "Memory" in your User’s Guide ).
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

A possible system board resource and/or hardware failure has occurred.

  • Perform the procedures in "Restoring Your Operating System" in your User’s Guide .
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).
Page 29 of the Dell DCDO user manual — Diagnostic Lights
Page 29 · click to enlarge
Page 29

Light Pattern Problem Description Suggested Resolution

A possible expansion card failure has occurred.

1 Determine if a conflict exists by removing an expansion card (not a graphics card) and restarting the computer (see "Cards" in your User’s Guide).

2 If the problem persists, reinstall the card you removed, and then remove a different card and restart the computer.

3 Repeat this process for each expansion card installed. If the computer starts normally, troubleshoot the last card removed from the computer for resource conflicts (see "Restoring Your Operating System" in your User’s Guide).

4 If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide).

Another failure has occurred.

  • Ensure that all hard drive and CD/DVD drive cables are properly connected to the system board (see "System Board Components" in your User’s Guide ).
  • If there is an error message on the screen identifying a problem with a device (such as the floppy drive or hard drive), check the device to make sure it is functioning properly.
  • If the operating system is attempting to boot from a device (such as the floppy drive or CD/DVD drive), check the system setup program (see "System Setup" in your User’s Guide ) to ensure the boot sequence is correct for the devices installed on your computer.
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).
Page 30 of the Dell DCDO user manual — Beep Codes
Page 30 · click to enlarge
Page 30

Beep Codes

Your computer may emit a series of beeps during start up. The series of beeps is called a beep code and can be used to help identify a problem with your computer.

If your computer emits a series of beeps during start-up:

1 Write down the beep code.

2 Run the Dell Diagnostics to identify the cause (see "Dell Diagnostics" on page 33).

2 short, 1 long BIOS checksum error

1 long, 3 short, 2 short Memory error

1 short F12 key pressed

Code (repetitive short beeps)

1 BIOS checksum failure. Possible motherboard failure.

Contact Dell (see "Contacting Dell" in your User’s Guide).

2 No memory modules are detected.

  • If two or more memory modules are installed, remove the modules (see "Memory" in your User’s Guide ), reinstall one module, and then restart the computer. If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error.
  • If available, install working memory of the same type into your computer (see "Memory" in your User’s Guide ).
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

3 Possible motherboard failure.

Contact Dell (see "Contacting Dell" in your User’s Guide).

Code Cause · Description Suggested Remedy

Page 31 of the Dell DCDO user manual — System Messages
Page 31 · click to enlarge
Page 31

Code (repetitive short beeps)

4 RAM Read/Write failure.

  • Ensure that no special requirements for memory module/connector placement exist (see "Memory" in your User’s Guide ).
  • Ensure that the memory you are using is supported by your computer (see "Memory" in your User’s Guide ).
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

5 Real time clock failure. Possible battery failure or motherboard failure.

  • Replace the battery (see "Replacing the Battery" in your User’s Guide ).
  • If the problem persists, contact Dell (see "Contacting Dell" in your User’s Guide ).

6 Video BIOS Test Failure.

Dell (see "Contacting Dell" in your User’s Guide).

System Messages

documentation for either the operating system or the program that was running when the message appeared.

ALERT! PREVIOUS ATTEMPTS AT BOOTING THIS SYSTEM HAVE FAILED AT

CHECKPOINT [NNNN]. FOR HELP IN RESOLVING THIS PROBLEM, PLEASE NOTE THIS

CHECKPOINT AND CONTACT DELL TECHNICAL SUPPORT — The computer failed to complete the boot routine three consecutive times for the same error (see "Contacting Dell" in your User’s Guide for assistance).

CMOS CHECKSUM ERROR — Possible motherboard failure or the real-time clock battery charge is low. Replace the battery (see "Replacing the Battery" or "Contacting Dell" in your User’s Guide for assistance).

CPU FAN FAILURE — CPU fan failure. Replace the CPU fan (see "Removing the Processor" in your User’s Guide).

FLOPPY DISKETTE SEEK FAILURE — A cable may be loose, or the computer configuration information may not match the hardware configuration. Check cable connections (see "Contacting Dell" in your User’s Guide for assistance).

Description Suggested Remedy

Page 32 of the Dell DCDO user manual — Hardware Troubleshooter
Page 32 · click to enlarge
Page 32

DISKETTE READ FAILURE — The floppy disk may be defective or a cable may be loose. Replace the floppy disk and/or check for a loose cable connection.

HARD-DISK READ FAILURE — Possible hard drive failure during hard-drive boot test (see "Contacting Dell" in your User’s Guide for assistance).

KEYBOARD FAILURE — Keyboard failure or the keyboard cable is loose (see "Keyboard Problems" in your User’s Guide).

NO BOOT DEVICE AVAILABLE — The system cannot detect a bootable device or partition.

  • If the floppy drive is your boot device, ensure that the cables are connected and that a bootable floppy disk is in the drive.
  • If the hard drive is your boot device, ensure that the cables are connected and that the drive is installed properly and partitioned as a boot device.
  • Enter the system setup program and ensure that the boot sequence information is correct (see "Entering System Setup" in your User’s Guide ).

NO TIMER TICK INTERRUPT — System board failure or a chip on the system board might be malfunctioning (see "Contacting Dell" in your User’s Guide for assistance).

NON-SYSTEM DISK OR DISK ERROR — Replace the floppy disk with one that has a bootable operating system or remove the floppy disk from drive A and restart the computer.

NOT A BOOT DISKETTE — Insert a bootable floppy disk and restart your computer.

A PARAMETER HAS EXCEEDED ITS NORMAL OPERATING RANGE. DELL RECOMMENDS

THAT YOU BACK UP YOUR DATA REGULARLY. A PARAMETER OUT OF RANGE MAY OR

MAY NOT INDICATE A POTENTIAL HARD DRIVE PROBLEM — S.M.A.R.T error, possible HDD failure. This feature can be enabled or disabled in BIOS setup.

Hardware Troubleshooter

If a device is either not detected during the operating system setup or is detected, but incorrectly configured, you can use the Hardware Troubleshooter to resolve the incompatibility.

Windows XP:

1 Click Start→ Help and Support. 2 Type hardware troubleshooter in the search field and press to start the search. 3 In the Fix a Problem section, click Hardware Troubleshooter. 4 In the Hardware Troubleshooter list, select the option that best describes the problem and click Next to follow the remaining troubleshooting steps.

Page 33 of the Dell DCDO user manual — Starting the Dell Diagnostics From Your Hard Drive
Page 33 · click to enlarge
Page 33

Windows Vista:

1 Click the Windows Vista start button , and click Help and Support.

2 Type hardware troubleshooter in the search field and press to start the search.

3 In the search results, select the option that best describes the problem and follow the remaining troubleshooting steps.

Dell Diagnostics

When to Use the Dell Diagnostics

If you experience a problem with your computer, perform the checks in "Lockups and Software Problems" (see "Troubleshooting" in your User’s Guide) and run the Dell Diagnostics before you contact Dell for assistance.

You can run the Dell Diagnostics from your hard drive or from the Drivers and Utilities disc.

See "System Setup" in your User’s Guide to review your computer’s configuration information, and ensure that the device that you want to test displays in the system setup program and is active.

Starting the Dell Diagnostics From Your Hard Drive

The Dell Diagnostics is located on a separate diagnostic utility partition on your hard drive.

your User’s Guide.

1 Turn on (or restart) your computer.

Page 34 of the Dell DCDO user manual — Starting the Dell Diagnostics From the Drivers and Utilities Disc
Page 34 · click to enlarge
Page 34

2 When the DELL logo appears, press immediately.

periods of time. To avoid possible keyboard failure, press and release in even intervals to open the Boot Device Menu.

partition has been found, run the Dell Diagnostics from your Drivers and Utilities disc (see "Starting the Dell Diagnostics From the Drivers and Utilities Disc" on page 34).

If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft Windows desktop, and then shut down your computer and try again.

3 At the Boot Device Menu, use the up- and down-arrow keys or press the appropriate number on the keyboard to highlight Boot to Utility Partition, and then press .

boot only. Upon restart, the computer boots according to the boot sequence specified in the system setup program.

4 At the Dell Diagnostics Main Menu, left-click with the mouse, or press and then , to select the test you want to run (see "Dell Diagnostics Main Menu" on page 35).

appear and follow the instructions on the screen.

5 After all tests have completed, close the test window to return to the Dell Diagnostics Main Menu.

6 Close the Main Menu window to exit the Dell Diagnostics and restart the computer.

Starting the Dell Diagnostics From the Drivers and Utilities Disc

1 Turn on your computer.

2 Press the eject button on the front of the optical drive to open the drive tray.

3 Place the Drivers and Utilities disc in the center of the drive tray, and then press the eject button or gently push on the tray to close it.

4 Restart the computer.

Page 35 of the Dell DCDO user manual — Dell Diagnostics Main Menu
Page 35 · click to enlarge
Page 35

5 When the DELL logo appears, press immediately.

for extended periods of time. To avoid possible keyboard failure, press and release in even intervals until the Boot Device Menu appears.

If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft Windows desktop, and then shut down your computer and try again.

6 At the Boot Device Menu, use the up- and down-arrow keys or press the appropriate number on the keyboard to highlight Onboard or USB CD-ROM, and then press .

boot only. Upon restart, the computer boots according to the boot sequence specified in the system setup program.

7 Press to select the Dell Diagnostics.

8 At the Dell Diagnostics Menu, press to select the Dell Diagnostics.

9 At the Dell Diagnostics Main Menu, left-click with the mouse, or press and then , to select the test you want to run (see "Dell Diagnostics Main Menu" on page 35).

appear and follow the instructions on the screen.

10 After all tests have completed, close the test window to return to the Dell Diagnostics Main Menu.

11 Remove the Drivers and Utilities disc, close the Main Menu window to exit the Dell Diagnostics, and then restart the computer.

Dell Diagnostics Main Menu

The following tests can be run from the Dell Diagnostics Main Menu:

Express Test Performs a quick test of system devices. The test typically takes 10 to 20 minutes and requires no interaction on your part. Run Express Test first to increase the possibility of tracing the problem quickly.

Option Function

Page 36 of the Dell DCDO user manual — Dell Diagnostics
Page 36 · click to enlarge
Page 36

Extended Test Performs a thorough check of system devices. The test typically takes an hour or more and periodically requires your input to answer specific questions.

Custom Test Tests a specific device in the system and can be used to customize the tests you want to run.

Symptom Tree Lists a number of common symptoms and allows you to select a test based on the symptom of the problem you are having.

For any problem encountered during a test, a message appears with an error code and a description of the problem. Write down the error code and problem description exactly as it appears and follow the instructions on the screen. If you cannot resolve the problem, contact Dell (see "Contacting Dell" in your User’s Guide).

When contacting Dell support, have your Service Tag ready.

The following tabs provide additional information for tests run from the Custom Test or Symptom Tree option:

Results Displays the results of the test and any error conditions encountered.

Errors Displays error conditions encountered, error codes, and the problem description.

Help Describes the test and any requirements for running the test.

Displays the hardware configuration for the selected device.

The Dell Diagnostics obtains configuration information for all devices from the system setup program, memory, and various internal tests, and it displays the information in the device list in the left pane of the screen. NOTE: The device list may not display the names of all the components installed on your computer or all devices attached to your computer.

Allows you to customize the test, if applicable, by changing the test settings.

Show 6 more labels / short text on this page
Option Function · Tab Function · Configuration · (Custom Test only) · Parameters · (Custom Test only)
Page 37 of the Dell DCDO user manual — Drive Problems
Page 37 · click to enlarge
Page 37

Troubleshooting

Follow these tips when you troubleshoot your computer:

  • If you added or removed a part before the problem started, review the installation procedures and ensure that the part is correctly installed.
  • If a peripheral device does not work, ensure that the device is properly connected.
  • If an error message appears on the screen, write down the exact message. This message may help support personnel diagnose and fix the problem(s).
  • If an error message occurs in a program, see the program’s documentation.

view, so they may not apply if you set your Dell™ computer to the Windows Classic view.

Battery Problems

installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.

REPLACE THE BATTERY — If you have to repeatedly reset time and date information after turning on the computer, or if an incorrect time or date displays during start-up, replace the battery (see "Replacing the Battery" in your User’s Guide). If the battery still does not work properly, contact Dell (see "Contacting Dell" in your User’s Guide).

Drive Problems

ENSURE THAT MICROSOFT WINDOWS RECOGNIZES THE DRIVE —

Windows XP:

  • Click Start and click My Computer .

Windows Vista:

  • Click Start and click Computer .

If the drive is not listed, perform a full scan with your antivirus software to check for and remove viruses. Viruses can sometimes prevent Windows from recognizing the drive.

Page 38 of the Dell DCDO user manual — Hard Drive Problems
Page 38 · click to enlarge
Page 38

T EST THE DRIVE —

  • Insert another disc to eliminate the possibility that the original drive is defective.
  • Insert a bootable floppy disk and restart the computer.

CLEAN THE DRIVE OR DISK — See "Cleaning Your Computer" on page 23.

C HECK THE CABLE CONNECTIONS

RUN THE HARDWARE TROUBLESHOOTER — See "Restoring Your Operating System" in your User’s Guide.

RUN THE DELL DIAGNOSTICS — See "Dell Diagnostics" on page 33.

Optical Drive Problems

does not indicate a defect in the drive or the disc.

DVD titles work in all DVD drives.

A DJUST THE W INDOWS VOLUME CONTROL —

  • Click the speaker icon in the lower-right corner of your screen.
  • Ensure that the volume is turned up by clicking the slidebar and dragging it up.
  • Ensure that the sound is not muted by clicking any boxes that are checked.

CHECK THE SPEAKERS AND SUBWOOFER — See "Sound and Speaker Problems" on page 49.

Problems Writing to an Optical Drive

CLOSE OTHER PROGRAMS — The optical drive must receive a steady stream of data during the writing process. If the stream is interrupted, an error occurs. Try closing all programs before you write to the optical.

TURN OFF STANDBY MODE IN WINDOWS BEFORE WRITING TO A DISC — Search for the keyword standby in Windows Help and Support for information on power management modes.

Hard Drive Problems

R UN C HECK D ISK —

Windows XP:

1 Click Start and click My Computer.

2 Right-click Local Disk C:.

3 Click Properties→ Tools→ Check Now.

4 Click Scan for and attempt recovery of bad sectors and click Start.

Page 39 of the Dell DCDO user manual — E-Mail, Modem, and Internet Problems
Page 39 · click to enlarge
Page 39

Windows Vista:

1 Click Start and click Computer.

2 Right-click Local Disk C:.

3 Click Properties→ Tools→ Check Now.

The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to continue the desired action.

4 Follow the instructions on the screen.

E-Mail, Modem, and Internet Problems

operate while it is connected to a digital telephone network.

(see "Back Panel Connectors" in your User’s Guide).

CHECK THE MICROSOFT OUTLOOK EXPRESS SECURITY SETTINGS — If you cannot open your e-mail attachments:

1 In Outlook Express, click Tools→ Options→ Security.

2 Click Do not allow attachments to remove the check mark, as needed.

CHECK THE TELEPHONE LINE CONNECTION CHECK THE TELEPHONE JACK CONNECT THE MODEM DIRECTLY TO THE TELEPHONE WALL JACK USE A DIFFERENT TELEPHONE LINE —

  • Verify that the telephone line is connected to the jack on the modem (the jack has either a green label or a connector-shaped icon next to it).
  • Ensure that you hear a click when you insert the telephone line connector into the modem.
  • Disconnect the telephone line from the modem and connect it to a telephone; then listen for a dial tone.
  • If you have other telephone devices sharing the line, such as an answering machine, fax machine, surge protector, or line splitter, bypass them and use the telephone to connect the modem directly to the telephone wall jack. If you are using a line that is 3 meters (10 feet) or more in length, try a shorter line.
Page 40 of the Dell DCDO user manual — Error Messages
Page 40 · click to enlarge
Page 40

RUN THE MODEM DIAGNOSTIC TOOL —

Windows XP:

1 Click Start→ All Programs→ Modem Helper.

2 Follow the instructions on the screen to identify and resolve modem problems. Modem Helper is not available on certain computers.

Windows Vista:

1 Click Start → All Programs→ Modem Diagnostic Tool.

2 Follow the instructions on the screen to identify and resolve modem problems. Modem diagnostics are not available on all computers.

VERIFY THAT THE MODEM IS COMMUNICATING WITH WINDOWS —

Windows XP:

1 Click Start→ Control Panel→ Printers and Other Hardware→ Phone and Modem Options→ Modems.

2 Click the COM port for your modem, and then click Properties→ Diagnostics→ Query Modem to verify that the modem is communicating with Windows.

If all commands receive responses, the modem is operating properly.

Windows Vista:

1 Click Start → Control Panel→ Hardware and Sound→ Phone and Modem Options→ Modems.

2 Click the COM port for your modem, and then click Properties→ Diagnostics→ Query Modem to verify that the modem is communicating with Windows.

If all commands receive responses, the modem is operating properly.

ENSURE THAT YOU ARE CONNECTED TO THE INTERNET — Ensure that you have subscribed to an Internet provider. With the Outlook Express e-mail program open, click File. If Work Offline has a check mark next to it, click the check mark to remove it and connect to the Internet. For help, contact your Internet service provider.

Error Messages

If the error message is not listed, see the documentation for the operating system or the program that was running when the message appeared.

A FILENAME CANNOT CONTAIN ANY OF THE FOLLOWING CHARACTERS: \ / : * ? “ < > | — Do not use these characters in filenames.

Page 41 of the Dell DCDO user manual — IEEE 1394 Device Problems
Page 41 · click to enlarge
Page 41

A REQUIRED .DLL FILE WAS NOT FOUND — The program that you are trying to open is missing an essential file. To remove and then reinstall the program:

Windows XP:

1 Click Start→ Control Panel→ Add or Remove Programs→ Programs and Features.

2 Select the program you want to remove.

3 Click Uninstall.

4 See the program documentation for installation instructions.

Windows Vista:

1 Click Start → Control Panel→ Programs→ Programs and Features.

2 Select the program you want to remove.

3 Click Uninstall.

4 See the program documentation for installation instructions.

drive letter :\ IS NOT ACCESSIBLE. THE DEVICE IS NOT READY — The drive cannot read the disk. Insert a disk into the drive and try again.

INSERT BOOTABLE MEDIA — Insert a bootable floppy disk, CD, or DVD.

NON-SYSTEM DISK ERROR — Remove the floppy disk from the floppy drive and restart your computer.

NOT ENOUGH MEMORY OR RESOURCES. CLOSE SOME PROGRAMS AND TRY

AGAIN — Close all windows and open the program that you want to use. In some cases, you may have to restart your computer to restore computer resources. If so, run the program that you want to use first.

OPERATING SYSTEM NOT FOUND — Contact Dell (see "Contacting Dell" in your User’s Guide).

IEEE 1394 Device Problems

ENSURE THAT THE CABLE FOR THE IEEE 1394 DEVICE IS PROPERLY INSERTED INTO

THE DEVICE AND INTO THE CONNECTOR ON THE COMPUTER

ENSURE THAT THE IEEE 1394 DEVICE IS ENABLED IN SYSTEM SETUP — See "System Setup Options" in your User’s Guide.

ENSURE THAT THE IEEE 1394 DEVICE IS RECOGNIZED BY WINDOWS —

Windows XP:

1 Click Start and click Control Panel.

2 Under Pick a Category, click Performance and Maintenance→ System→ System Properties→ Hardware→ Device Manager.

Page 42 of the Dell DCDO user manual — THE ELECTRICAL OUTLET
Page 42 · click to enlarge
Page 42

Windows Vista:

1 Click Start → Control Panel→ Hardware and Sound.

2 Click Device Manager.

If your IEEE 1394 device is listed, Windows recognizes the device.

ENSURE THAT THE IEEE 1394 CARD IS PROPERLY SEATED

ENSURE THAT THE IEEE 1394 CABLE IS CONNECTED SECURELY TO THE SYSTEM

BOARD CONNECTOR AND THE CONNECTOR ON THE FRONT I/O PANEL

IF YOU HAVE PROBLEMS WITH A DELL IEEE 1394 DEVICE — Contact Dell (see "Contacting Dell" in your User’s Guide).

IF YOU HAVE PROBLEMS WITH AN IEEE 1394 DEVICE NOT PROVIDED BY DELL —

Contact the IEEE 1394 device manufacturer.

Keyboard Problems

C HECK THE KEYBOARD CABLE —

  • Ensure that the keyboard cable is firmly connected to the computer.
  • Shut down the computer (see "Turning Off Your Computer" in your User’s Guide ), reconnect the keyboard cable as shown on the setup diagram for your computer, and then restart the computer.
  • Ensure that the cable is not damaged or frayed and check cable connectors for bent or broken pins. Straighten any bent pins.
  • Remove any keyboard extension cables and connect the keyboard directly to the computer.

TEST THE KEYBOARD — Connect a properly working keyboard to the computer, and then try using the keyboard.

RUN THE HARDWARE TROUBLESHOOTER — See "Restoring Your Operating System" in your User’s Guide.

Lockups and Software Problems

The computer does not start up

CHECK THE DIAGNOSTIC LIGHTS — See "Diagnostic Lights" on page 26.

ENSURE THAT THE POWER CABLE IS FIRMLY CONNECTED TO THE COMPUTER AND TO

THE ELECTRICAL OUTLET

Page 43 of the Dell DCDO user manual — E ND THE PROGRAM —
Page 43 · click to enlarge
Page 43

The computer stops responding

TURN THE COMPUTER OFF — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds (until the computer turns off), and then restart your computer.

A program stops responding

E ND THE PROGRAM —

1 Press simultaneously to access the Task Manager.

2 Click the Applications tab.

3 Click to select the program that is no longer responding.

4 Click End Task.

A program crashes repeatedly

a floppy disk, CD, or DVD.

CHECK THE SOFTWARE DOCUMENTATION — If necessary, uninstall and then reinstall the program.

A program is designed for an earlier Windows operating system

RUN THE PROGRAM COMPATIBILITY WIZARD —

Windows XP:

The Program Compatibility Wizard configures a program so that it runs in an environment similar to non-Windows XP operating system environments.

1 Click Start→ All Programs→ Accessories→ Program Compatibility Wizard→ Next.

2 Follow the instructions on the screen.

Windows Vista:

The Program Compatibility Wizard configures a program so that it runs in an environment similar to non-Windows Vista operating system environments.

1 Click Start → Control Panel→ Programs→ Use an older program with this version of Windows.

2 In the welcome screen, click Next.

3 Follow the instructions on the screen.

Page 44 of the Dell DCDO user manual — I F YOU EXPERIENCE OTHER MEMORY PROBLEMS —
Page 44 · click to enlarge
Page 44

A solid blue screen appears

TURN THE COMPUTER OFF — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds (until the computer turns off), and then restart your computer.

CHECK THE SOFTWARE DOCUMENTATION OR CONTACT THE SOFTWARE

MANUFACTURER FOR TROUBLESHOOTING INFORMATION —

  • Ensure that the program is compatible with the operating system installed on your computer.
  • Ensure that your computer meets the minimum hardware requirements needed to run the software. See the software documentation for information.
  • Ensure that the program is installed and configured properly.
  • Verify that the device drivers do not conflict with the program.
  • If necessary, uninstall and then reinstall the program.

B ACK UP YOUR FILES IMMEDIATELY

USE A VIRUS-SCANNING PROGRAM TO CHECK THE HARD DRIVE, FLOPPY DISKS, CDS, OR DVDS

SAVE AND CLOSE ANY OPEN FILES OR PROGRAMS AND SHUT DOWN YOUR

COMPUTER THROUGH THE S TART MENU

Memory Problems

IF YOU RECEIVE AN INSUFFICIENT MEMORY MESSAGE —

  • Save and close any open files and exit any open programs you are not using to see if that resolves the problem.
  • See the software documentation for minimum memory requirements. If necessary, install additional memory (see "Installing a Memory Module" in your User’s Guide ).
  • Reseat the memory modules (see "Removing the Front Panel" in your User’s Guide ) to ensure that your computer is successfully communicating with the memory.
  • Run the Dell Diagnostics (see "Dell Diagnostics" on page 33).

I F YOU EXPERIENCE OTHER MEMORY PROBLEMS —

  • Reseat the memory modules (see "Removing the Front Panel" in your User’s Guide ) to ensure that your computer is successfully communicating with the memory.

Other software problems

Page 45 of the Dell DCDO user manual — C HECK THE MOUSE SETTINGS —
Page 45 · click to enlarge
Page 45
  • Ensure that you are following the memory installation guidelines (see "Installing a Memory Module" in your User’s Guide ).
  • Ensure that the memory you are using is supported by your computer. For more information about the type of memory supported by your computer, see "Removing the Front Panel" in your User’s Guide .
  • Run the Dell Diagnostics (see "Dell Diagnostics" on page 33).

Mouse Problems

C HECK THE MOUSE CABLE —

  • Ensure that the cable is not damaged or frayed and check cable connectors for bent or broken pins. Straighten any bent pins.
  • Remove any mouse extension cables, and connect the mouse directly to the computer.
  • Verify that the mouse cable is connected as shown on the setup diagram for your computer.

R ESTART THE COMPUTER —

1 Simultaneously press to display the Start menu.

2 Press , press the up- and down-arrow keys to highlight Shut down or Turn Off, and then press .

3 After the computer turns off, reconnect the mouse cable as shown on the setup diagram.

4 Turn on the computer.

TEST THE MOUSE — Connect a properly working mouse to the computer, and then try using the mouse.

C HECK THE MOUSE SETTINGS —

Windows XP:

1 Click Start→ Control Panel→ Mouse.

2 Adjust the settings as needed.

Windows Vista:

1 Click Start → Control Panel→ Hardware and Sound→ Mouse.

2 Adjust the settings as needed.

REINSTALL THE MOUSE DRIVER — See "Drivers" in your User’s Guide.

RUN THE HARDWARE TROUBLESHOOTER — See "Restoring Your Operating System" in your User’s Guide.

Page 46 of the Dell DCDO user manual — Power Problems
Page 46 · click to enlarge
Page 46

Network Problems

CHECK THE NETWORK LIGHT ON THE FRONT OF THE COMPUTER — If the link integrity light is off (see "Controls and Lights" in your User’s Guide), no network communication is occurring. Replace the network cable.

CHECK THE NETWORK CABLE CONNECTOR — Ensure that the network cable is firmly inserted into the network connector on the back of the computer and the network jack.

RESTART THE COMPUTER AND ATTEMPT TO LOG ON TO THE NETWORK AGAIN

CHECK YOUR NETWORK SETTINGS — Contact your network administrator or the person who set up your network to verify that your network settings are correct and that the network is functioning.

RUN THE HARDWARE TROUBLESHOOTER — See "Restoring Your Operating System" in your User’s Guide.

Power Problems

IF THE POWER LIGHT IS GREEN AND THE COMPUTER IS NOT RESPONDING — See "Diagnostic Lights" on page 26.

IF THE POWER LIGHT IS BLINKING GREEN — The computer is in standby mode. Press a key on the keyboard, move the mouse, or press the power button to resume normal operation.

IF THE POWER LIGHT IS OFF — The computer is either turned off or is not receiving power.

  • Reseat the power cable in the power connector on the back of the computer and the electrical outlet.
  • Bypass power strips, power extension cables, and other power protection devices to verify that the computer turns on properly.
  • Ensure that any power strips being used are plugged into an electrical outlet and are turned on.
  • Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
  • Ensure that the main power cable and front panel cable are securely connected to the system board (see "System Board Components" in your User’s Guide ).
Page 47 of the Dell DCDO user manual — E NSURE THAT THE PRINTER IS TURNED ON
Page 47 · click to enlarge
Page 47

IF THE POWER LIGHT IS BLINKING AMBER — The computer is receiving electrical power, but an internal power problem may exist.

  • Ensure that the voltage selection switch is set to match the AC power at your location (if applicable).
  • Ensure that all components and cables are properly installed and securely connected to the system board (see "System Board Components" in your User’s Guide ).

IF THE POWER LIGHT IS STEADY AMBER — A device may be malfunctioning or incorrectly installed.

  • Remove and then reinstall all memory modules (see "Removing the Front Panel" in your User’s Guide ).
  • Remove and then reinstall any expansion cards, including graphics cards (see "Cards" in your User’s Guide ).

ELIMINATE INTERFERENCE — Some possible causes of interference are:

  • Power, keyboard, and mouse extension cables
  • Too many devices connected to the same power strip
  • Multiple power strips connected to the same electrical outlet

Printer Problems

manufacturer.

CHECK THE PRINTER DOCUMENTATION — See the printer documentation for setup and troubleshooting information.

E NSURE THAT THE PRINTER IS TURNED ON

C HECK THE PRINTER CABLE CONNECTIONS —

  • See the printer documentation for cable connection information.
  • Ensure that the printer cables are securely connected to the printer and the computer.

TEST THE ELECTRICAL OUTLET — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.

VERIFY THAT THE PRINTER IS RECOGNIZED BY WINDOWS —

Windows XP:

1 Click Start→ Control Panel→ Printers and Other Hardware→ View installed printers or fax printers.

2 If the printer is listed, right-click the printer icon.

Page 48 of the Dell DCDO user manual — C HECK THE CABLE CONNECTIONS —
Page 48 · click to enlarge
Page 48

3 Click Properties→ Ports. For a parallel printer, ensure that the Print to the following port(s): setting is LPT1 (Printer Port). For a USB printer, ensure that the Print to the following port(s): setting is USB.

Windows Vista:

1 Click Start → Control Panel→ Hardware and Sound→ Printer.

2 If the printer is listed, right-click the printer icon.

3 Click Properties, and then click Ports.

4 Adjust the settings, as needed.

REINSTALL THE PRINTER DRIVER — See the printer documentation for information on reinstalling the printer driver.

Scanner Problems

manufacturer.

CHECK THE SCANNER DOCUMENTATION — See the scanner documentation for setup and troubleshooting information.

UNLOCK THE SCANNER — Ensure that your scanner is unlocked (if the scanner has a locking tab or button).

RESTART THE COMPUTER AND TRY THE SCANNER AGAIN

C HECK THE CABLE CONNECTIONS —

  • See the scanner documentation for information on cable connections.
  • Ensure that the scanner cables are securely connected to the scanner and the computer.

VERIFY THAT THE SCANNER IS RECOGNIZED BY MICROSOFT WINDOWS —

Windows XP:

1 Click Start→ Control Panel→ Printers and Other Hardware→ Scanners and Cameras.

2 If your scanner is listed, Windows recognizes the scanner.

Windows Vista:

1 Click Start → Control Panel→ Hardware and Sound→ Scanners and Cameras.

2 If the scanner is listed, Windows recognizes the scanner.

REINSTALL THE SCANNER DRIVER — See the scanner documentation for instructions.

Page 49 of the Dell DCDO user manual — R UN THE SPEAKER DIAGNOSTICS
Page 49 · click to enlarge
Page 49

Sound and Speaker Problems

No sound from speakers

volume setting. Always check to ensure that the volume on the media player(s) has not been turned down or off.

CHECK THE SPEAKER CABLE CONNECTIONS — Ensure that the speakers are connected as shown on the setup diagram supplied with the speakers. If you purchased a sound card, ensure that the speakers are connected to the card.

ENSURE THAT THE SUBWOOFER AND THE SPEAKERS ARE TURNED ON — See the setup diagram supplied with the speakers. If your speakers have volume controls, adjust the volume, bass, or treble to eliminate distortion.

ADJUST THE WINDOWS VOLUME CONTROL — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted.

DISCONNECT HEADPHONES FROM THE HEADPHONE CONNECTOR — Sound from the speakers is automatically disabled when headphones are connected to the computer’s front-panel headphone connector.

TEST THE ELECTRICAL OUTLET — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.

ELIMINATE POSSIBLE INTERFERENCE — Turn off nearby fans, fluorescent lights, or halogen lamps to check for interference.

R UN THE SPEAKER DIAGNOSTICS

REINSTALL THE SOUND DRIVER — See "Drivers" in your User’s Guide.

RUN THE HARDWARE TROUBLESHOOTER — See "Restoring Your Operating System" in your User’s Guide.

No sound from headphones

CHECK THE HEADPHONE CABLE CONNECTION — Ensure that the headphone cable is securely inserted into the headphone connector (see "About Your Computer" in your User’s Guide).

ADJUST THE WINDOWS VOLUME CONTROL — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted.

Page 50 of the Dell DCDO user manual — C HECK THE MONITOR POWER LIGHT —
Page 50 · click to enlarge
Page 50

Video and Monitor Problems

removal of the card is not necessary when installing additional graphics cards; however, the card is required for troubleshooting purposes. If you remove the card, store it in a safe and secure location. For information about your graphics card, go to support.dell.com.

The screen is blank

C HECK THE MONITOR CABLE CONNECTION —

  • Ensure that the monitor cable is connected to the correct graphics card (for dual graphics card configurations).
  • If you are using a DVI-to-VGA adapter, ensure that the adapter is correctly attached to the graphics card and monitor.
  • Ensure that the monitor cable is connected as shown on the setup diagram for your computer.
  • Remove any video extension cables and connect the monitor directly to the computer.
  • Swap the computer and monitor power cables to determine if the monitor’s power cable is defective.
  • Check the connectors for bent or broken pins (it is normal for monitor cable connectors to have missing pins).

C HECK THE MONITOR POWER LIGHT —

  • If the power light is lit or blinking, the monitor has power.
  • If the power light is off, firmly press the button to ensure that the monitor is turned on.
  • If the power light is blinking, press a key on the keyboard or move the mouse to resume normal operation.

TEST THE ELECTRICAL OUTLET — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.

CHECK THE DIAGNOSTIC LIGHTS — See "Diagnostic Lights" on page 26.

Page 51 of the Dell DCDO user manual — INTERFERENCE
Page 51 · click to enlarge
Page 51

The screen is difficult to read

C HECK THE MONITOR CABLE CONNECTION —

  • Ensure that the monitor cable is connected to the correct graphics card (for dual graphics card configurations).
  • If you are using the optional DVI-to-VGA adapter, ensure that the adapter is correctly attached to the graphics card and monitor.
  • Ensure that the monitor cable is connected as shown on the setup diagram for your computer.
  • Remove any video extension cables and connect the monitor directly to the computer.
  • Swap the computer and monitor power cables to determine if the monitor’s power cable is defective.
  • Check the connectors for bent or broken pins (it is normal for monitor cable connectors to have missing pins).

C HECK THE MONITOR POWER LIGHT —

  • If the power light is lit or blinking, the monitor has power.
  • If the power light is off, firmly press the button to ensure that the monitor is turned on.
  • If the power light is blinking, press a key on the keyboard or move the mouse to resume normal operation.

TEST THE ELECTRICAL OUTLET — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.

CHECK THE DIAGNOSTIC LIGHTS — See "Diagnostic Lights" on page 26.

CHECK THE MONITOR SETTINGS — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing (degaussing) the monitor, and running the monitor self-test.

MOVE THE SUBWOOFER AWAY FROM THE MONITOR — If your speaker system includes a subwoofer, ensure that the subwoofer is positioned at least 60 centimeters (2 feet) away from the monitor.

MOVE THE MONITOR AWAY FROM EXTERNAL POWER SOURCES — Fans, fluorescent lights, halogen lamps, and other electrical devices can cause the screen image to appear shaky. Turn off nearby devices to check for interference.

ROTATE THE MONITOR TO ELIMINATE SUNLIGHT GLARE AND POSSIBLE

INTERFERENCE

Page 52 of the Dell DCDO user manual — A DJUST THE W INDOWS DISPLAY SETTINGS —
Page 52 · click to enlarge
Page 52

A DJUST THE W INDOWS DISPLAY SETTINGS —

Windows XP:

1 Click Start→ Control Panel→ Appearance and Themes.

2 Click the area you want to change or click the Display icon.

3 Try different settings for Color quality and Screen resolution.

Windows Vista:

1 Click Start → Control Panel→ Hardware and Sound→ Personalization→ Display Settings.

2 Adjust Resolution and Colors settings, as needed.

3D image quality is poor

CHECK THE GRAPHICS CARD POWER CABLE CONNECTION — Ensure that the power cable for the graphics card(s) is correctly attached to the card.

CHECK THE MONITOR SETTINGS — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing (degaussing) the monitor, and running the monitor self-test.

Only part of the screen is readable

TURN ON THE COMPUTER AND THE MONITOR AND ADJUST THE MONITOR

BRIGHTNESS AND CONTRAST CONTROLS — If the monitor works, the graphics card(s) may be defective. Contact Dell (see "Contacting Dell" in your User’s Guide).

Page 59 of the Dell DCDO user manual — Dell Precision™ T7400 Guide de référence rapide
Page 59 · click to enlarge
Page 59

Dell Precision™ T7400 Guide de référence rapide

w w w. d e l l . c o m | s u p p o r t . d e l l . c o m

Modèle DCDO

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Dell DCDO

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Dell DCDO

Be the first to ask — other owners or our team will answer.

Original document

Dell DCDO manual PDF

252 pages·5.3 MB·Fan·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…