EN
Dell logo
Official user manual

Dell Desktop Computer (DCCY)

217 pages·6.7 MB·Fan·PDF·ENDEFRITNLJA
Dell Desktop Computer (DCCY)
Table of Contents 80 sections Dell™ OptiPlex™ 740 User's Guide · Mini Tower Computer · Desktop Computer · Small Form Factor Computer · … ShowHide
Dell™ OptiPlex™ 740 User's Guidep.1Mini Tower Computerp.1Desktop Computerp.1Small Form Factor Computerp.1Advanced Featuresp.2Dell™ OptiPlex™ 740 Systems User's Guidep.2LegacySelect Technology Controlp.2Manageabilityp.2Alert Standard Formatp.2Dell OpenManage™ IT Assistantp.2Dell OpenManage Client Instrumentationp.2Securityp.3Chassis Intrusion Detectionp.3Option Settingsp.3Padlock Ring and Security Cable Slotp.3Password Protectionp.3System Passwordp.3Assigning a System Passwordp.4Typing Your System Passwordp.4Deleting or Changing an Existing System Passwordp.5Administrator Passwordp.5Assigning an Administrator Passwordp.5Operating Your Computer With an Administrator Password Enabledp.5Deleting or Changing an Existing Administrator Passwordp.5Disabling a Forgotten Password and Setting a New Passwordp.6Trusted Platform Module (TPM)p.6Enabling the TPM Featurep.6System Setupp.6Overviewp.6Entering System Setupp.7System Setup Screenp.7System Setup Optionsp.7Changing Boot Sequence for the Current Bootp.10Changing Boot Sequence for Future Bootsp.11Booting to a USB Devicep.11Memory Keyp.11Floppy Drivep.11Jumper Settingsp.11Mini Tower, Desktop, and Small Form Factor Computersp.11Clearing Forgotten Passwordsp.12Clearing CMOS Settingsp.13HyperTransport™ and Dual -Core Technologyp.13Power Managementp.13About RAID Configurationsp.14Verifying That RAID Is Workingp.14RAID Level 0 Configurationp.14RAID Level 1 Configurationp.15Configuring Your Hard Drives for RAIDp.15Setting Your Computer to RAID-Enabled Modep.15Using the NVIDIA MediaShield ROM Utilityp.15Using NVIDIA MediaShieldp.16Creating a RAID Arrayp.16Deleting a RAID Arrayp.17Converting From One RAID Configuration to Another RAID Configurationp.17Rebuilding a RAID Configurationp.18Enabling Cool 'n' Quiet™ Technologyp.18Batteryp.19Replacing the Batteryp.19Before You Beginp.21Recommended Toolsp.21Turning Off Your Computerp.21Before Working Inside Your Computerp.21Cleaning Your Computerp.23Computer, Keyboard, and Monitorp.23Mousep.23Cleaning a Non-Optical Mousep.23Cleaning an Optical Mousep.23CDs and DVDsp.24About Your Desktop Computerp.25Front Viewp.25Back Viewp.26Back-Panel Connectorsp.26Inside Your Computerp.27System Board Componentsp.28PCI, PCI Express Cards, and PS/2 Serial Port Adaptersp.30PCI Cardsp.30Installing a PCI Cardp.30Removing a PCI Cardp.31Installing a PCI Card in the Riser-Card Cagep.32Removing a PCI Card From the Riser-Card Cagep.34
Page 1 of the Dell Desktop Computer (DCCY) user manual — Dell™ OptiPlex™ 740 User's Guide
Page 1 · click to enlarge
Page 1

Dell™ OptiPlex™ 740 User's Guide

Mini Tower Computer

Desktop Computer

Small Form Factor Computer

Page 2 of the Dell Desktop Computer (DCCY) user manual — Dell OpenManage Client Instrumentation
Page 2 · click to enlarge
Page 2

Advanced Features

Dell™ OptiPlex™ 740 Systems User's Guide

HyperTransport™ and Dual-Core Technology

Trusted Platform Module (TPM)

Booting to a USB Device

Enabling Cool 'n' Quiet™ Technology

LegacySelect Technology Control

LegacySelect technology control offers legacy-full, legacy-reduced, or legacy-free solutions based on common platforms, hard-drive images, and help desk procedures. Control is provided to the administrator through system setup, Dell OpenManage™ IT Assistant, or Dell custom factory integration.

LegacySelect allows administrators to electronically activate or deactivate connectors and media devices that include serial and USB connectors, a parallel connector, a floppy drive, PCI slots, and a PS/2 mouse. Connectors and media devices that are deactivated make resources available. You must restart the computer to effect the changes.

Manageability

Alert Standard Format

ASF is a DMTF management standard that specifies "pre-operating system" or "operating system-absent" alerting techniques. The standard is designed to generate an alert on potential security and fault conditions when the operating system is in a sleep mode or the system is turned off. ASF is designed to supersede previous operating-system-absent alerting technologies.

Your computer supports the following ASF version 1.03 and 2.0 alerts and remote capabilities:

AlertDescription Chassis: Chassis Intrusion – Physical Security Violation/Chassis Intrusion – Physical Security Violation Event ClearedThe computer chassis with the chassis intrusion feature installed and enabled has been opened or the chassis intrusion alert has been cleared. CPU: Emergency Shutdown EventThe processor temperature is too hot and the power supply has shut down. Cooling Device: Generic Critical Fan Failure/Generic Critical Fan Failure ClearedThe fan speed (rpm) is out of limits or the fan speed (rpm) problem has been resolved. Temperature: Generic Critical Temperature Problem/Generic Critical Temperature Problem ClearedThe computer temperature is out of limits or the computer temperature problem has been resolved. Battery LowThe system battery has reached a voltage of 2.2 V or lower.

For more information about Dell's ASF implementation, see the ASF User's Guide and the ASF Administrator's Guide, which are available on the Dell Support website at support.dell.com.

Dell OpenManage™ IT Assistant

IT Assistant configures, manages, and monitors computers and other devices on a corporate network. IT Assistant manages assets, configurations, events (alerts), and security for computers equipped with industry-standard management software. It supports instrumentation that conforms to SNMP, DMI, and CIM industry standards.

Dell OpenManage Client instrumentation, which is based on DMI and CIM, is available for your computer. For information on IT Assistant, see the Dell OpenManage IT Assistant User's Guide available on the Dell Support website at support.dell.com.

Dell OpenManage Client Instrumentation

Dell OpenManage Client Instrumentation is software that enables remote management programs such as IT Assistant to do the following:

l Access information about your computer, such as how many processors it has and what operating system it is running.

l Monitor the status of your computer, such as listening for thermal alerts from temperature probes or hard-drive failure alerts from storage devices.

l Change the state of your computer, such as updating its BIOS or shutting it down remotely.

Show 10 more labels / short text on this page
LegacySelect Technology Control · Jumper Settings · Manageability · Clearing Forgotten Passwords · Security · Clearing CMOS Settings · Password Protection · Power Management · System Setup · About RAID Configurations
Page 3 of the Dell Desktop Computer (DCCY) user manual — System Password
Page 3 · click to enlarge
Page 3

A managed system is one that has Dell OpenManage Client Instrumentation set up on a network that uses IT Assistant. For information about Dell OpenManage Client Instrumentation, see the Dell OpenManage Client Instrumentation User's Guide available on the Dell Support website at support.dell.com.

Security

Chassis Intrusion Detection

This feature, if installed and enabled, detects that the chassis was opened and alerts the user. To change the Chassis Intrusion setting:

1. Enter system setup (see Entering System Setup). 2. Press the down-arrow key to move to the Security option. 3. Press to access the Security option's pop-up menu. 4. Press the down-arrow key to move to the Chassis Intrusion setting. 5. Press to select an option setting. 6. Press again after you update the option setting. 7. Exit and save system setup.

Option Settings

l On — If the computer cover is opened, the setting changes to Detected, and the following alert message displays during the boot routine at the next

computer start-up:

Alert! Cover was previously removed.

To reset the Detected setting, enter system setup (see Entering System Setup). In the Chassis Intrusion option, press the left- or right-arrow key to select Reset, and then choose On, On-Silent, or Off.

l On-Silent (default setting) — If the computer cover is opened, the setting changes to Detected. No alert message appears during the boot sequence

at the next computer start-up.

l Off — No intrusion monitoring occurs and no messages appear.

Padlock Ring and Security Cable Slot

Use one of the following methods to secure your computer:

l Use a padlock alone or a padlock and looped security cable with the padlock ring.

A padlock alone prevents the computer from being opened.

A security cable looped around a stationary object is used in conjunction with a padlock to prevent unauthorized movement of the computer.

l Attach a commercially available antitheft device to the security cable slot on the back of the computer.

Antitheft devices usually include a segment of metal-stranded cable with an attached locking device and key. The documentation that comes with the device contains instructions for installing it.

Password Protection

System Password

Page 4 of the Dell Desktop Computer (DCCY) user manual — Typing Your System Password
Page 4 · click to enlarge
Page 4

Option Settings

You cannot change or enter a new system password if either of the following two options is displayed:

l Set — A system password is assigned.

l Disabled — The system password is disabled by a jumper setting on the system board.

You can only assign a system password when the following option is displayed:

l Not Set — No system password is assigned and the password jumper on the system board is in the enabled position (the default setting).

Assigning a System Password

1. Enter system setup and verify that Password Status is set to Unlocked . 2. Highlight System Password , and then press the leftor right-arrow key.

The option heading changes to Enter Password, followed by an empty 32-character field in square brackets.

3. Type your new system password.

You can use up to 32 characters. To erase a character when entering your password, press or the left-arrow key. The password is not case sensitive.

Certain key combinations are not valid. If you enter one of these combinations, the speaker emits a beep.

As you press each character key (or the spacebar for a blank space), a placeholder appears in the field.

4. Press .

If the new system password is less than 32 characters, the whole field fills with placeholders. Then the option heading changes to Verify Password, followed by another empty 32-character field in square brackets.

5. To confirm your password, type it a second time and press .

The password setting changes to Set.

6. Exit system setup.

Password protection takes effect when you restart the computer.

Typing Your System Password

When you start or restart your computer, the following prompt appears on the screen.

If Password Status is set to Locked:

Type the password and press .

If you have assigned an administrator password, the computer accepts your administrator password as an alternate system password.

If you type a wrong or incomplete system password, the following message appears on the screen:

** Incorrect password. **

If you again type an incorrect or incomplete system password, the same message appears on the screen. The third and subsequent times you type an incorrect or incomplete system password, the computer displays the following message:

** Incorrect password. ** Number of unsuccessful password attempts: 3 System halted! Must power down.

Even after your computer is turned off and on, the previous message is displayed each time you type an incorrect or incomplete system password.

Page 5 of the Dell Desktop Computer (DCCY) user manual — Deleting or Changing an Existing Administrator Password
Page 5 · click to enlarge
Page 5

Deleting or Changing an Existing System Password

1. Enter system setup (see Entering System Setup). 2. Highlight System Password and press . 3. When prompted, type the system password. 4. Press twice to clear the existing system password. The setting changes to Not Set .

If Not Set is displayed, the system password is deleted. If Not Set is not displayed, press , press the left- and right-arrow keys to highlight Save/Exit, and then press to restart the computer and implement your changes. Then repeat steps 3 and 4.

5. To assign a new password, follow the procedure in Assigning a System Password . 6. Exit system setup.

Administrator Password

Option Settings

You cannot change or enter a new administrator password if either of the following two options is displayed:

l Set — An administrator password is assigned.

l Disabled — The administrator password is disabled by a jumper setting on the system board.

You can only assign an administrator password when the following option is displayed:

l Not Set — No administrator password is assigned and the password jumper on the system board is in the enabled position (the default setting).

Assigning an Administrator Password

The administrator password can be the same as the system password.

1. Enter system setup and verify that Admin Password is set to Not Set (see Entering System Setup ). 2. Highlight Admin Password and press the leftor right-arrow key.

The computer prompts you to type and verify the password. If you enter a character that is not permitted, the computer emits a beep.

3. Type and then verify the password.

After you verify the password, the Admin Password setting changes to Set. The next time you enter system setup, the computer prompts you for the administrator password.

4. Exit system setup.

A change to Admin Password becomes effective immediately (no need to restart the computer).

Operating Your Computer With an Administrator Password Enabled

When you enter system setup, the Admin Password option is highlighted, prompting you to type the password (see Entering System Setup).

If you do not type the correct password, the computer lets you view, but not modify, system setup options.

Deleting or Changing an Existing Administrator Password

Page 6 of the Dell Desktop Computer (DCCY) user manual — System Setup
Page 6 · click to enlarge
Page 6

To change an existing administrator password, you must know the administrator password.

1. Enter system setup (see Entering System Setup ). 2. Type the administrator password at the prompt. 3. Highlight Admin Password and press the leftor right-arrow key to delete the existing administrator password.

The setting changes to Not Set.

To assign a new administrator password, perform the steps in Assigning an Administrator Password.

4. Exit system setup.

Disabling a Forgotten Password and Setting a New Password

To reset system and/or administrator passwords, see Clearing Forgotten Passwords.

Trusted Platform Module (TPM)

TPM is a hardware-based security feature that can be used to create and manage computer-generated encryption keys. When combined with security software, the TPM enhances existing network and computer security by enabling features such as file protection capabilities and protected e-mail. The TPM feature is enabled through a system setup option.

Enabling the TPM Feature

1. Enable the TPM software:

a. Restart the computer and press during the Power On Self Test to enter the system setup program. b. Select Security, then select TPM Security and press . c. Under TPM Security, select On. d. Press to exit the setup program. e. If prompted, click Save/Exit. 2. Activate the TPM setup program:

a. Restart the computer and press during the Power On Self Test to enter the system setup program. b. Select Security, then select TPM Activation and press . c. Under TPM Activation, select Activate and press .

Once the process is complete, the computer either restarts automatically or prompts you to restart your computer.

System Setup

Overview

Use system setup as follows:

l To change the system configuration information after you add, change, or remove any hardware in your computer

l To set or change a user-selectable option such as the user password

Page 7 of the Dell Desktop Computer (DCCY) user manual — System Setup Options
Page 7 · click to enlarge
Page 7

l To read the current amount of memory or set the type of hard drive installed

Before you use system setup, it is recommended that you write down the system setup screen information for future reference.

Entering System Setup

1. Turn on (or restart) your computer. 2. When the blue DELL™ logo is displayed, you must watch for the F2 prompt to appear. 3. Once this F2 prompt appears, press immediately.
4. If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft ® Windows ® desktop, then, shut down your computer (see Turning Off Your Computer ) and try again.

System Setup Screen

The system setup screen displays current or changeable configuration information for your computer. Information on the screen is divided into four areas: the menu at the top, the main window, the Item Help field on the right, and key functions listed on the bottom.

Options List — This field appears on the left side of the system setup window. The field is a scrollable list containing features that define the configuration of your computer, including installed hardware, power conservation, and security features.

Option Field — This field contains information about each option. In this field you can view your current settings and make changes to your settings.

Scroll up and down the list by using the up- and down-arrow keys. As an option is highlighted, the Option Field displays more information about that option and the option's current and available settings.

Use the right- and left-arrow keys to highlight an option. Press to make that selection active.

Key Functions — This field appears below the Option Field and lists keys and their functions within the active system setup field.

System Setup Options

System System InfoLists the computer name, BIOS Version, Service Tag, Express Service Code, (if applicable), and the Asset Tag. None of these fields can be modified. Processor InfoIdentifies the CPU type, processor clock speed, bus speed, clock speed, and L2 cache size. States whether the processor is multiple-core capable and whether it supports 64-bit technology. Memory InfoLists the type, size, speed, and channel mode (dual or single) of installed memory. PCI InfoIdentifies any installed PCI or PCI Express cards. Date/TimeDisplays current date and time settings. Boot SequenceThe computer attempts to boot from the sequence of devices specified in this list. HDD Boot SequenceLists the order that the BIOS will search the available hard drives in the system.

Diskette Drive This option enables or disables the floppy drive. The options are Off, USB, Internal, and Read Only.

Drives

Page 8 of the Dell Desktop Computer (DCCY) user manual — Entering System Setup
Page 8 · click to enlarge
Page 8
SATA 0 through SATA nIdentifies and enables and disables the drives attached to the SATA connectors on the system board and lists the capacities for the hard drives. NOTE: These options appear as SATA 0 through SATA 3 for the mini tower, SATA 0 through SATA 2 for the desktop, and SATA 0 and SATA1 for the small form factor. External SATAIdentifies and enables and disables the drives attached to the eSATA connector on the system board and lists the capacities for the hard drives. SATA Operation (RAID Autodetect/AHCI default for mini tower and desktop computers) (AHCI default for small form factor computers)Options for mini tower and desktop computers: l RAID Autodetect/AHCI (RAID if signed drives, otherwise AHCI) l RAID Autodetect/ATA (RAID if signed drives, otherwise ATA) l RAID On (SATA is configured for RAID on every boot) NOTE: When in Autodetect mode, the computer configures the drive as RAID if a RAID signature is detected on the drive. Otherwise the drive will be configured as AHCI or ATA. Options for small form factor computers: l AHCI l ATA SMART Reporting (Off default)This setting determines whether integrated drive errors are reported or not during system startup.
Onboard Devices Integrated NIC (On default)Enables or disables the integrated NIC controller. Settings are Off, On, On w/ PXE, or On w/RPL. When the On w/ PXE or the On w/RPL setting is active, if a boot routine is not available from the network server, the computer attempts to boot from the next device in the boot sequence list. Integrated Audio (On default)Enables or disables the onboard audio controller. USB Controller (On default)Enables or disables the internal USB controller. No Boot enables the controller but disables the ability to boot from a USB device. NOTE: Operating systems with USB support will recognize USB floppy drives regardless of the No Boot setting. USB 0 through 5 (On default)Enables or disables the USB ports on the back of the computer. Front USB Ports (On default)Enables or disables the front USB ports. LPT Port Mode (PS/2 default)Determines the mode of operation of the internal parallel port. AT configures the port for AT compatibility. PS/2 configures the port for PS/2 compatibility. EPP configures the port for the Enhanced Parallel Port bidirectional protocol. ECP configures the port for the Extended Capability Port bidirectional protocol. NOTE: If you set the LPT Port Mode to ECP, the LPT Port DMA appears in the option menu. LPT Port AddressDetermines the address that the built-in parallel port uses. Serial Port #1 (Auto default)Determines how the serial port operates. Auto, the default setting, automatically configures a connector to a particular designation (COM1 or COM3). Serial Port #2 (Auto default)Determines how the serial port operates. Auto, the default setting, automatically configures a connector to a particular designation (COM2 or COM4). PS/2 Mouse PortEnables or disables the integrated legacy PS/2 mouse controller.

Primary This setting specifies which video controller is primary when there are two video controllers available (PCI, Onboard, Auto, and PEG). This

(Internal default) · Video

Page 9 of the Dell Desktop Computer (DCCY) user manual — Entering System Setup
Page 9 · click to enlarge
Page 9

selection only matters if there are two video controllers present. When Auto is selected, the add-in video controller will be used.

This setting configures the amount of system memory that is reserved for the integrated video controller. The settings are Auto, 16MB, 32MB, 64MB, 128MB, or Off.

HDD Acoustic Mode (Bypass default) l Bypass — Your computer does not test or change the current acoustics mode setting.

l Quiet — The hard drive operates at its most quiet setting.

l Suggested — The hard drive operates at the level suggested by the drive manufacturer.

l Performance — The hard drive operates at its maximum speed.

Security Unlock SetupWhen an administrator password is being used, allows the user access to modify system setup settings. Enter the administrator password at the prompt to unlock system setup. If the correct password is not entered here, the user can view but not modify system setup fields. Admin PasswordDisplays the current status of your system setup program's password security feature and allows you to verify and assign a new admin password. System Password (Not Set default)Displays the current status of the system's password security feature and allows a new system password to be assigned and verified. Drive 0-n Password (Not Set default)Displays the current status of the hard drive's password security feature and allows a new hard drive password to be assigned and verified. Password Changes (Unlocked default)Determines the interaction between the System password and the Admin password. Locked prevents a user without a valid Admin password from being able to modify the System password. Unlocked allows a user with a valid System password to modify the system password. Chassis Intrusion (On-Silent default)When enabled and the switch installed, this option alerts the user, during the next computer start-up, that the computer cover has been opened. The settings are On, On-Silent (default setting), and Off. Intrusion AlertAcknowledges and clears a chassis intrusion alert. TPM Security (Off default)Enables or disables the Trusted Platform Module security device. TPM Activation (Deactivate default)Activates or deactivates the Trusted Platform Module security device. The Clear option clears any data stored by a user that has previously activated and used TPM. NOTE: In order to activate Trusted Platform Module, the TPM Security option must be set to On. Non-Execute Disable (On default)Enables or disables Execute Disable memory protection technology.
Power Management AC Recovery (Off default)Determines how the system responds when AC power is re-applied after a power loss. Off commands the system to stay off when the power is re-applied. You must press the front-panel power button before the system turns on. On commands the system to turn on when the power is re-applied. Last commands the system to return to the last power state the system was in just before it was turned off. Auto Power On (Off default)Sets the computer to automatically turn on. Off disables this feature. Everyday turns the computer on every day at the time set in Auto Power Time. Weekdays turns the computer on every day from Monday through Friday at the time set in Auto Power Time. NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector.

Sets time to automatically turn on the computer.

Time is kept in the standard 12-hour format (hours:minutes). Change the startup time by pressing the right- or left-arrow key to increase or

Show 6 more labels / short text on this page
Video · (Auto default) · Video Memory Size · (64MB default) · Performance · Auto Power Time
Page 10 of the Dell Desktop Computer (DCCY) user manual — Changing Boot Sequence for the Current Boot
Page 10 · click to enlarge
Page 10

decrease the numbers, or type numbers in both the date and time fields.

Low Power Mode (On default)When Low Power Mode is selected, remote wakeup events will no longer power up the computer from Hibernate or Off via the onboard network controller. Remote Wake-Up (Off default)This option allows the system to power up when a Network Interface Controller or Remote Wakeup-capable modem receives a wake up signal. On is the default setting. On w/ Boot to NIC will allow the computer to attempt to boot from a network prior to using the boot sequence. NOTE: Normally, the system can be powered up remotely from suspend mode, hibernate mode, or when powered off. When Low Power Mode (in the Power Management menu) is enabled, the system can only be powered up remotely from Suspend. Suspend Mode (S3 default)Sets the computer's suspend mode. The options are S1, a suspend state in which the computer is running in a low-power mode, and S3, a suspend state in which the power is reduced or turned off for many components, however, system memory remains active.
Maintenance Service TagDisplays the service tag for your computer. ASF Mode (On default)This setting controls the ASF functionality. On enables full ASF functionality, Alert Only sends ASF messages on the event or error, and Off disables all ASF functionality. Load DefaultsRestores system setup options to their factory defaults. Event LogAllows you to view the Event Log. Entries are marked R for Read and U for Unread. Mark All Entries Read puts an R to the left of all the entries. Clear Log clears the Event Log.
POST Behavior Fastboot (On default)When enabled, this feature reduces computer startup time by bypassing some compatibility steps. Off does not skip any steps during computer startup. On starts the system more quickly. Numlock Key (On default)Determines the functionality of the numeric keys on the right side of your keyboard. Off commands the right keypad keys to function as arrows. On commands the right keypad keys to function as numbers. POST HotkeysDetermines whether the sign-on screen displays a message stating the keystroke sequence that is required to enter the Setup program or the Quickboot feature. Setup & Boot Menu displays both messages (F2=Setup and F12=Boot Menu). Setup displays the setup message only (F2=Setup). Boot Menu displays the Quickboot message only (F12=Boot Menu). None displays no message. Keyboard ErrorsWhen set to Report (enabled) and an error is detected during POST, the BIOS will display the error message and prompt you to press <F1> to continue or press <F2> to enter system setup. When set to Do Not Report (disabled) and an error is detected during POST, the BIOS will display the error message and continue booting the system.

Changing Boot Sequence for the Current Boot

You can use this feature, for example, to restart your computer to a USB device, such as a floppy drive, memory key, or CD-RW drive.

1. If you are booting to a USB device, connect the USB device to a USB connector (see Front View for mini tower computers, or Front View for desktop computers). 2. Turn on (or restart) your computer. 3. When F2 = Setup, F12 = Boot Menu appears in the upper-right corner of the screen, press .

If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft Windows desktop, then shut down your computer (see Turning Off Your Computer) and try again.

4. Use the arrow keys to select Continue .

The Boot Device Menu appears, listing all available boot devices.

5. Use the arrow keys to select the appropriate device (for the current boot only).
Page 11 of the Dell Desktop Computer (DCCY) user manual — Jumper Settings
Page 11 · click to enlarge
Page 11

Changing Boot Sequence for Future Boots

1. Enter system setup (see Entering System Setup ). 2. Use the leftand right-arrow keys to highlight the Boot menu option, then press to access the menu.
3. Press the upand down-arrow keys to highlight the appropriate Boot Device option ( 1st - 4th Boot Device are available options). 4. Press the upand down-arrow keys to move through the list of devices. 5. Press to select a device to be the 1st , 2nd , 3rd , or 4th Boot Device , (as applicable).

Booting to a USB Device

Memory Key

1. Insert the memory key into a USB port and restart the computer. 2. When F12 = Boot Menu appears in the upper-right corner of the screen, press .

The BIOS detects the device and adds the USB device option to the boot menu.

3. From the boot menu, select the number that appears next to the USB device.

The computer boots to the USB device.

Floppy Drive

1. In system setup, set the Diskette Drive option to USB . 2. Save and exit system setup. 3. Connect the USB floppy drive, insert a bootable floppy, and re-boot the system.

Jumper Settings

Mini Tower, Desktop, and Small Form Factor Computers

Page 12 of the Dell Desktop Computer (DCCY) user manual — Clearing Forgotten Passwords
Page 12 · click to enlarge
Page 12
Dell Desktop Computer (DCCY) — Clearing Forgotten Passwords diagram (page 12)
Fig. 1 · Clearing Forgotten Passwords
JumperSettingDescription PSWDPassword features are enabled (default setting). Password features are disabled. jumpered unjumpered

Clearing Forgotten Passwords

1. Follow the procedures in Before You Begin. 2. If clearing the password on a small form factor computer, remove the hard drive (see Drives). 3. Locate the 2-pin password jumper (PSWD) on the system board, and remove the jumper to clear the password (see Jumper Settings). 4. If clearing the password on a small form factor computer, install the hard drive (see Drives). 5. Replace the computer cover (see Replacing the Computer Cover). 6. Connect your computer and monitor to electrical outlets, and turn them on. 7. After the Microsoft® Windows® desktop appears on your computer, shut down your computer. (see Turning Off Your Computer) 8. Turn off the monitor and disconnect it from the electrical outlet. 9. Disconnect the computer power cable from the electrical outlet, and press the power button to ground the system board. 10. Open the computer cover (see Removing the Computer Cover for mini tower computers, Removing the Computer Cover for desktop computers and Removing the Computer Cover for small form factor computers). 11. Remove the hard drive (Removing a Hard Drive). 12. Locate the 2-pin password jumper on the system board and attach the jumper to reenable the password feature. 13. Replace the hard drive (Installing a Hard Drive). 14. Replace the computer cover (see Replacing the Computer Cover).

Page 13 of the Dell Desktop Computer (DCCY) user manual — Power Management
Page 13 · click to enlarge
Page 13
15. Connect your computer and devices to electrical outlets, and turn them on.
16. Assign a new system and/or administrator password.

Clearing CMOS Settings

1. Follow the procedures in Before You Begin .
2. If clearing the CMOS setting on a small form factor computer, remove the hard drive (see Removing a Hard Drive ). 3. Reset the current CMOS settings:

a. Locate the password and CMOS jumpers. Password (PSWD) and CMOS (RTC_RST) jumpers are on the system board (see Jumper Settings). b. Remove the password jumper plug from its pins. c. Place the password jumper plug on the RTC_RST pins and wait approximately 5 seconds. d. Remove the jumper plug from the RTC_RST pins and place it back on the password pins. 4. If clearing the CMOS setting on a small from factor computer, install the hard drive (see Installing a Hard Drive). 5. Replace the computer cover (see Replacing the Computer Cover).

6. Connect your computer and devices to electrical outlets, and turn them on.

HyperTransport™ and Dual -Core Technology

HyperTransport technology can increase overall computer performance by removing I/O bottlenecks, increasing system bandwidth, and reducing system latency. A fully integrated DDR memory controller allows a direct connection between the processor and the main memory. Dual-Core is a technology in which two physical computational units exist inside a single processor package, thereby increasing computing efficiency and multi-tasking ability.

While many programs can benefit from HyperTransport and dual-core technology, some programs may have not been optimized for them and may require an update from the software manufacturer. Contact the software manufacturer for updates and information about using HyperTransport or dual-core technology with your software. To determine if your computer is using HyperTransport technology, check the system setup option for HyperTransport under the Performance tab (see System Setup).

Power Management

Your computer can be set to use less power when you are not working. You control the power usage through the operating system installed on your computer and certain option settings in system setup. These periods of reduced power are called "sleep modes."

l Standby. In this sleep mode, power is reduced or turned off for most components, including the cooling fans. However, system memory remains active.

l Hibernate. This sleep mode reduces power consumption to a minimum by writing all data in system memory to a hard drive and then removing system

power. Waking up from this mode restarts the computer, and the memory contents are restored. Operation then resumes where the computer left off when it entered the hibernation mode.

l Shutdown. This sleep mode removes all power from the computer except a small auxiliary amount. As long as the computer remains connected to an

electrical outlet, it can be automatically or remotely started. For example, the Auto Power On option in system setup allows the computer to automatically start at a specified time. Also, your network administrator can remotely start your computer using a power management event such as Remote Wake Up.

The following table lists the sleep modes and the methods you can use to wake the computer from each mode.

Page 14 of the Dell Desktop Computer (DCCY) user manual — RAID Level 0 Configuration
Page 14 · click to enlarge
Page 14

Sleep Mode Wake-Up Methods (Windows XP)

Standby l Press the power button

l Auto power on

l Move or click the mouse

l Type on the keyboard

l USB device activity

l Power management event

Hibernate l Press the power button

l Auto power on

l Power management event

Shutdown l Press the power button

l Auto power on

l Power management event

About RAID Configurations

This section provides an overview of the RAID configuration that you may have selected when you purchased your computer. A number of RAID configurations are available in the computer industry for different types of uses. The Dell mini tower and desktop models of your OptiPlex computer support RAID level 0 and RAID level 1. (RAID support is not available for the small form factor model.) A RAID level 0 configuration is recommended for high-performance programs, while RAID level 1 is recommended for users that desire a high level of data integrity.

The NVIDIA RAID controller on your computer can only create a RAID level configuration using two physical drives. The drives should be the same size to ensure that the larger drive does not contain unallocated (and therefore unusable) space.

Verifying That RAID Is Working

Your computer displays information pertaining to your RAID configuration at start-up, before loading the operating system. If RAID is not configured, the message none defined appears under RAID Volumes, followed by a list of the physical drives installed in your computer. If a RAID volume is identified, you can then check the Status field to determine the current state of your RAID configuration. The Status field contains information about the following conditions:

l Normal — Your RAID configuration is functioning properly.

l Degraded — One of your hard drives has failed. The computer is still bootable; however, RAID is not functioning and data is not being copied to the

other drive.

l Rebuild — Following a degraded condition, the computer has detected the replacement/connection of a secondary hard drive and will automatically

restore the RAID configuration the next time the operating system loads.

RAID Level 0 Configuration

RAID level 0 uses a storage technique known as data striping to provide a high data-access rate. Data striping is a method of writing consecutive segments, or stripes, of data sequentially across the physical drive(s) to create a large virtual drive. Data striping allows one of the drives to read data while the other drive is searching for and reading the next block.

Dell Desktop Computer (DCCY) — RAID Level 0 Configuration diagram (page 14)
Fig. 2 · RAID Level 0 Configuration

Another advantage of a RAID level 0 configuration is that it utilizes the full storage capacities of the drives. For example, two 120-GB hard drives combine to provide 240 GB of hard drive space on which to store data.

Page 15 of the Dell Desktop Computer (DCCY) user manual — Using the NVIDIA MediaShield ROM Utility
Page 15 · click to enlarge
Page 15

RAID Level 1 Configuration

RAID level 1 uses a data-redundancy storage technique known as mirroring to enhance data integrity. When data is written to the primary drive, the data is also duplicated, or mirrored, on the second drive in the configuration. A RAID level 1 configuration sacrifices high data-access rates for its data redundancy advantages.

Dell Desktop Computer (DCCY) — RAID Level 1 Configuration diagram (page 15)
Fig. 3 · RAID Level 1 Configuration

If a drive failure occurs, subsequent read and write operations are directed to the surviving drive. A replacement drive can then be rebuilt using the data from the surviving drive.

Configuring Your Hard Drives for RAID

Your computer can be configured for RAID, even if you did not select a RAID configuration when the computer was purchased. For an explanation of RAID levels and their requirements, see About RAID Configurations. For information on how to install a hard drive, see Installing a Hard Drive for your mini tower computer or Installing a Hard Drive for your desktop computer.

You can use one of two methods to configure RAID hard drive volumes. The first method uses the NVIDIA MediaShield ROM utility and is performed before you install the operating system onto the hard drive. The second method uses NVIDIA MediaShield and is performed after you have installed the operating system and NVIDIA RAID drivers.Both methods require that you set your computer to RAID-enabled mode before you begin.

Setting Your Computer to RAID-Enabled Mode

1. Enter system setup (see Entering System Setup ). 2. Press the upand down-arrow keys to highlight Drives , then press . 3. Press the upand down-arrow keys to highlight the applicable SATA drive, then press . 4. Press the leftand right-arrow keys to highlight RAID On , and then press . Repeat the process, as needed, for each SATA hard drive.
5. Press , press the leftand right-arrow keys to highlight Save/Exit , and then press to exit system setup and resume the boot process.

Using the NVIDIA MediaShield ROM Utility

Hard drives of any size may be used to create a RAID configuration. Ideally, however, the drives should be of equal size to avoid unallocated or unused space. For an explanation of RAID levels and their requirements, see About RAID Configurations. For information on how to install a hard drive, see Installing a Hard Drive for your mini tower computer or Installing a Hard Drive for your desktop computer.

1. Enable RAID for each applicable hard drive on your computer (see Setting Your Computer to RAIDEnabled Mode ). 2. Restart the computer.
Page 16 of the Dell Desktop Computer (DCCY) user manual — Creating a RAID Array
Page 16 · click to enlarge
Page 16
3. Press when prompted to enter the RAID BIOS.

The Define a New Array window appears.

4. Press to navigate to the RAID Mode field.

To create a RAID 0 configuration, use the arrow keys to select Striping.

To create a RAID 1 configuration, use the arrow keys to select Mirroring.

5. Press to navigate to the Free Disks field. 6. Use the upand down-arrow keys to select a hard drive to include in the RAID array and then use the right-arrow key to move the selected drive from the Free Disks field to the Array Disks field. Repeat for each disk you want to include in the RAID array.
7. After assigning the hard drives to an array, press .

The Clear disk data prompt appears.

8. Press to clear all data from the selected drives.

The Array List window appears.

9. To review the details of the array that you set up, use the arrow keys to highlight the array in the Array Detail window and press .

The Array Detail window appears.

10. Press to return to the previous screen. 11. Press to exit the RAID BIOS.

Using NVIDIA MediaShield

NVIDIA MediaShield allows you to create, view, and manage RAID configurations.

Hard drives of any size may be used to create a RAID configuration using NVIDIA MediaShield. Ideally, however, the drives should be of equal size to avoid unallocated or unused space. For an explanation of RAID levels and their requirements, see About RAID Configurations.

Creating a RAID Array

1. Enable RAID on your hard drives (see Setting Your Computer to RAID-Enabled Mode ). 2. After rebooting your computer, launch NVIDIA MediaShield. 3. Click Create under System Tasks .

The NVIDIA Create Array Wizard appears and lists the disks that are available for configuration.

4. Click Next .
Page 17 of the Dell Desktop Computer (DCCY) user manual — Converting From One RAID Configuration to Another RAID Configuration
Page 17 · click to enlarge
Page 17
5. Click Custom , then click Next . 6. Use the drop-down box to select Striping (RAID 0) or Mirroring (RAID 1). 7. Click Next .

The Free Disk Selection window appears.

8. Click to select the drives that will make up the RAID configuration, click Next , and then click Next again.

The Clearing System Data window appears.

9. Click Next . 10. Click Finish to create the RAID configuration.

The MediaShield RAID management utility window appears and lists the array along with any other installed hard drives.

Deleting a RAID Array

1. Launch NVIDIA MediaShield. 2. Click to select the array you want to delete. 3. Click Delete Array in the System Tasks pane.

The NVIDIA Delete Array Wizard appears.

4. Click Next .

A confirmation screen appears with the name and size of the array that you have marked for deletion.

5. Click Finish to delete the RAID configuration.

The MediaShield RAID management utility window appears and lists any remaining arrays along with any other installed hard drives.

Converting From One RAID Configuration to Another RAID Configuration

NVIDIA MediaShield utilizes a one-step process known as migrating to change the current state of a disk or array without losing any data. If needed, additional hard drives can be added to an existing array, including a single-drive RAID 0 configuration for conversion to a two-drive RAID 0 configuration; however, the capacity of the resulting array must be equal to or greater than the size of the original configuration.

RAID 1 to RAID 1 conversions cannot be performed using the migrating process.

1. Launch NVIDIA MediaShield. 2. Click to select the array you want to convert. 3. Click Convert Array in the System Tasks pane.
Page 18 of the Dell Desktop Computer (DCCY) user manual — Enabling Cool 'n' Quiet™ Technology
Page 18 · click to enlarge
Page 18

The NVIDIA Convert Array Wizard appears.

4. Click Next . 5. Under RAID Mode Selection , select Mirroring or Striping from the drop-down menu. 6. Click Next .
7. Under Free Disk Selection , select the hard drive(s) you want to include in the (migrated) array by clicking the checkbox beside it. 8. Click Finish .

The MediaShield RAID management utility window appears and displays the status of the upgrade/migration process along with any other installed hard drives.

Rebuilding a RAID Configuration

If one of the hard drives in a RAID array fails, you can rebuild the array by restoring the data to a replacement drive.

1. Launch NVIDIA MediaShield. 2. Click to select your RAID configuration ( Mirroring ) in the management utility window. 3. Select Rebuild Array in the System Tasks pane.

The NVIDIA Rebuild Array Wizard appears.

4. Click Next . 5. Select the hard drive you want to rebuild by clicking the checkbox beside it. 6. Click Next . 7. Click Finish .

The MediaShield RAID management utility window appears and displays the status of the rebuild process.

Enabling Cool 'n' Quiet™ Technology

The Cool 'n' Quiet technology controls your computer's processor performance automatically, dynamically adjusting the operating frequency and voltage, according to the task at hand. When an application does not require full performance, significant amounts of power can be saved. performance is designed to still be responsive, with maximum processor performance being delivered when required, and automatic power savings when possible.

1. Click on the Start ® Settings ® Control Panel ® Power Options to access the Power Options Properties window. 2. From the Power Schemes tab, click the Power Schemes drop-down menu and select Minimal Power Management and then click OK .

Cool 'n' Quiet technology is now enabled.

Page 19 of the Dell Desktop Computer (DCCY) user manual — Dell™ OptiPlex™ 740 Systems User's Guide
Page 19 · click to enlarge
Page 19

Battery

Dell™ OptiPlex™ 740 Systems User's Guide

Replacing the Battery

A coin-cell battery maintains computer configuration, date, and time information. The battery can last several years.

The battery may need replacing if an incorrect time or date is displayed during the boot routine along with a message such as:

Time-of-day not set - please run SETUP program

Invalid configuration information - please run SETUP program

Strike the F1 key to continue, F2 to run the setup utility

To determine whether you need to replace the battery, reenter the time and date in system setup and exit the program to save the information. Turn off your computer and disconnect it from the electrical outlet for a few hours; then reconnect the computer, turn it on, and enter system setup (see Entering System Setup). If the date and time are not correct in system setup, replace the battery.

You can operate your computer without a battery; however, without a battery, the configuration information is erased if the computer is turned off or unplugged from the electrical outlet. In this case, you must enter system setup and reset the configuration options.

To remove the battery:

1. If you have not already done so, make a copy of your configuration information, found in system setup (see System Setup). 2. Follow the procedures in Before You Begin. 3. If you have a Small Form Factor chassis, remove the hard disk drive to access the battery on the system board (see Removing a Hard Drive). 4. Locate the battery socket (see System Board Components for mini tower computers or System Board Components for desktop computers or System Board Components for small form factor computers).

NOTICE: If you pry the battery out of its socket with a blunt object, be careful not to touch the system board with the object. Ensure that the object is inserted between the battery and the socket before you attempt to pry out the battery. Otherwise, you may damage the system board by prying off the socket or by breaking circuit traces on the system board.

5. Remove the system battery.

a. Support the battery connector by pressing down firmly on the positive side of the connector. b. While supporting the battery connector, press the battery tab away from the positive side of the connector and pry the battery it up out of the securing tabs at the negative side of the connector.

Replacing the Battery · or · or

Page 20 of the Dell Desktop Computer (DCCY) user manual — Battery
Page 20 · click to enlarge
Page 20
Dell Desktop Computer (DCCY) — Battery diagram (page 20)
Fig. 4 · Battery

1 system battery 2 positive side of battery connector 3 battery socket

4 battery socket tab

6. Install the new system battery.

a. Support the battery connector by pressing down firmly on the positive side of the connector. b. Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector. c. Press the battery straight down into the connector until it snaps into place. 7. If you have a Small Form Factor chassis, install the hard disk drive (see Installing a Hard Drive). 8. Replace the computer cover (see Replacing the Computer Cover). 9. Enter system setup and restore the settings you recorded in step 1 (see Entering System Setup). 10. Properly dispose of the old battery as described in the Product Information Guide.

Page 21 of the Dell Desktop Computer (DCCY) user manual — Before Working Inside Your Computer
Page 21 · click to enlarge
Page 21

Before You Begin

Dell™ OptiPlex™ 740 Systems User's Guide

Turning Off Your Computer

Before Working Inside Your Computer

This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist:

l You have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer.

l You have read the safety information in your Dell™ Product Information Guide.

l A component can be replaced by performing the removal procedure in reverse order.

Recommended Tools

The procedures in this document may require the following tools:

l Small flat-blade screwdriver

l Flash BIOS update program floppy disk, CD, USB key

Turning Off Your Computer

1. Shut down the operating system:

a. Save and close any open files, and exit any open programs. b. Click the Start button, and then click Shut Down. c. In the Shut Down Windows window, select Shut down, and then click OK.

The computer turns off after the operating system shutdown process finishes.

2. Ensure that the computer and any attached devices are turned off.

If your computer and attached devices did not automatically turn off when you shut down your operating system, turn them off now.

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.

NOTICE: When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.

1. Turn off your computer.

Recommended Tools · l Phillips screwdriver

Page 22 of the Dell Desktop Computer (DCCY) user manual — Before You Begin
Page 22 · click to enlarge
Page 22
2. Disconnect any telephone or telecommunication lines from the computer. 3. Disconnect your computer and all attached devices from their electrical outlets, and then press the power button to ground the system board. 4. If applicable, remove the computer stand (for instructions, see the documentation that came with the stand).
5. Remove the computer cover:

l Remove the mini tower computer cover (see Removing the Computer Cover).

l Remove the desktop computer cover (see Removing the Computer Cover).

l Remove the small form factor computer cover (see Removing the Computer Cover).

Page 23 of the Dell Desktop Computer (DCCY) user manual — Floppy Drive
Page 23 · click to enlarge
Page 23

Cleaning Your Computer

Dell™ Optiplex™ 740 Systems User's Guide

Computer, Keyboard, and Monitor

Computer, Keyboard, and Monitor

l Use a can of compressed air to remove dust from between the keys on the keyboard.

l To clean your monitor screen, lightly dampen a soft, clean cloth with water. You can also use a special screen-cleaning tissue or solution suitable for the

monitor's antistatic coating.

l Wipe the keyboard, computer, and monitor plastics with a soft cleaning cloth moistened with a solution of three parts water and one part dishwashing

detergent.

Do not soak the cloth or let water drip inside your computer or keyboard.

Mouse

If your screen cursor skips or moves abnormally, clean the mouse.

Cleaning a Non-Optical Mouse

1. Clean the outside casing of the mouse with a cloth moistened with a mild cleaning solution. 2. Turn the retainer ring on the underside of your mouse counterclockwise, and then remove the ball. 3. Wipe the ball with a clean, lint-free cloth. 4. Blow carefully into the ball cage or use a can of compressed air to dislodge dust and lint. 5. If the rollers inside the ball cage are dirty, clean the rollers with a cotton swab moistened lightly with isopropyl alcohol. 6. Recenter the rollers in their channels if they are misaligned. Ensure that fluff from the swab is not left on the rollers. 7. Replace the ball and retainer ring, and turn the retainer ring clockwise until it clicks into place.

Cleaning an Optical Mouse

Clean the outside casing of the mouse with a cloth moistened with a mild cleaning solution.

Floppy Drive

Mouse · Floppy Drive · CDs and DVDs

Page 24 of the Dell Desktop Computer (DCCY) user manual — CDs and DVDs
Page 24 · click to enlarge
Page 24

Clean your floppy drive using a commercially available cleaning kit. These kits contain pretreated floppy disks to remove contaminants that accumulate during normal operation.

CDs and DVDs

If you notice problems, such as skipping, with the playback quality of your CDs or DVDs, try cleaning the discs.

1. Hold the disc by its outer edge. You can also touch the inside edge of the center hole.
2. With a soft, lint-free cloth, gently wipe the bottom of the disc (the unlabeled side) in a straight line from the center to the outer edge of the disc.

For stubborn dirt, try using water or a diluted solution of water and mild soap. You can also purchase commercial products that clean discs and provide some protection from dust, fingerprints, and scratches. Cleaning products for CDs are also safe to use on DVDs.

Page 25 of the Dell Desktop Computer (DCCY) user manual — About Your Desktop Computer
Page 25 · click to enlarge
Page 25

Desktop Computer

Dell™ Optiplex™ 740 Systems User's Guide

About Your Desktop Computer

About Your Desktop Computer

Front View

Dell Desktop Computer (DCCY) — About Your Desktop Computer diagram (page 25)
Fig. 5 · About Your Desktop Computer

1 USB 2.0 connectors (2)

Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see System Setup for more information about booting to a USB device).

It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

2 LAN indicator light

This light indicates that a local area network (LAN) connection is established.

3 power button Press this button to turn on the computer.

4 Dell badge This badge can be rotated to match the orientation of your computer. To rotate, place fingers around the outside of the badge, press firmly, and turn the badge. You can also rotate the badge using the slot provided near the bottom of the badge.

5 power light The power light illuminates and blinks or remains solid to indicate different operating states:

l No light — The computer is turned off.

l Steady green — The computer is in a normal operating state.

l Blinking green — The computer is in a power-saving mode.

l Blinking or solid amber — See Power Problems.

To exit from a power-saving mode, press the power button or use the keyboard or the mouse if it is configured as a wake device in the Windows Device Manager. For more information about sleep modes and exiting from a power-saving mode, see Power Management.

See System Lights for a description of light codes that can help you troubleshoot problems with your computer.

Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see Diagnostic Lights.

7 hard-drive activity light

This light flickers when the hard drive is being accessed.

Use the headphone connector to attach headphones and most kinds of speakers.

Use the microphone connector to attach a microphone.

Show 4 more labels / short text on this page
Inside Your Computer · 6 diagnostic lights · 8 headphone connector · 9 microphone connector
Page 26 of the Dell Desktop Computer (DCCY) user manual — Back-Panel Connectors
Page 26 · click to enlarge
Page 26

10 floppy drive Insert a floppy disk into this drive.

11 optical drive Insert media (if supported) into this drive.

Back View

Dell Desktop Computer (DCCY) — Back View diagram (page 26)
Fig. 6 · Back View

1 card slots Access connectors for any installed PCI and PCI Express cards.

Plug serial, USB, and other devices into the appropriate connectors (see Back-Panel Connectors).

Insert the power cable.

4 voltage selection switch

Your computer is equipped with a manual voltage-selection switch.

To help avoid damaging a computer with a manual voltage selection switch, set the switch for the voltage that most closely matches the AC power available in your location.

Also, ensure that your monitor and attached devices are electrically rated to operate with the AC power available in your location.

5 padlock ring Insert a padlock to lock the computer cover.

6 cover release latch

Allows you to open the computer cover.

Back-Panel Connectors

Dell Desktop Computer (DCCY) — Back-Panel Connectors diagram (page 26)
Fig. 7 · Back-Panel Connectors

Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.

2 link integrity light

l Green — A good connection exists between a 10-Mbps network and

the computer.

l Orange — A good connection exists between a 100-Mbps network

and the computer.

l Yellow — A good connection exists between a 1-Gbps (or 1000-

Mbps) network and the computer.

l Off — The computer is not detecting a physical connection to the

network.

3 network To attach your computer to a network or broadband device, connect one

2 back-panel connectors · 3 power connector · 1 parallel connector

Page 27 of the Dell Desktop Computer (DCCY) user manual — Inside Your Computer
Page 27 · click to enlarge
Page 27

end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached.

On computers with a network connector card, use the connector on the card.

It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.

4 network activity light

Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.

Use the green line-out connector to attach headphones and most speakers with integrated amplifiers.

On computers with a sound card, use the connector on the card.

Use the line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR.

On computers with a sound card, use the connector on the card.

7 USB 2.0 connectors (5)

Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

Plug the cable from your VGA-compatible monitor into the blue connector.

Connect a serial device, such as a handheld device, to the serial port. The default designations are COM1 for serial connector 1 and COM2 for serial connector 2.

For more information, see System Setup Options.

Inside Your Computer

Show 5 more labels / short text on this page
adapter connector · 5 line-out connector · 6 line-in connector · 8 video connector · 9 serial connector
Page 28 of the Dell Desktop Computer (DCCY) user manual — System Board Components
Page 28 · click to enlarge
Page 28
Dell Desktop Computer (DCCY) — System Board Components diagram (page 28)
Fig. 8 · System Board Components

1 drive release latch 2 optical drive 3 power supply

4 chassis intrusion switch (optional) 5 system board 6 card slots

7 heat sink assembly 8 front I/O panel

System Board Components

Dell Desktop Computer (DCCY) — System Board Components diagram (page 28)
Fig. 9 · System Board Components
Dell Desktop Computer (DCCY) — System Board Components diagram (page 28)
Fig. 10 · System Board Components

11 internal USB (USB1) 12 PCI Express x16 connector (SLOT1)

Page 29 of the Dell Desktop Computer (DCCY) user manual — System Board Components
Page 29 · click to enlarge
Page 29
Page 29 of the Dell Desktop Computer (DCCY) user manual — System Board Components
Page 30 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Card
Page 30 · click to enlarge
Page 30

PCI, PCI Express Cards, and PS/2 Serial Port Adapters

PCI, PCI Express Cards, and PS/2 Serial Port Adapters

Your Dell™ computer supports a PS/2 serial port adapter and provides the following connectors for PCI and PCI Express cards:

l Two low-profile PCI card slots

l One low-profile PCI Express x16 card slot

PCI Cards

Dell Desktop Computer (DCCY) — PCI Cards diagram (page 30)
Fig. 11 · PCI Cards

Installing a PCI Card

1. Follow the procedures in Before You Begin .

2. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 3. If you are installing a new card, remove the filler bracket to create a card-slot opening. Then continue with step 5. 4. If you are replacing a card that is already installed in the computer, remove the card (see Removing a PCI Card). If necessary, disconnect any cables connected to the card. Then continue with step 6. 5. Prepare the card for installation.

Dell Desktop Computer (DCCY) — Installing a PCI Card diagram (page 30)
Fig. 12 · Installing a PCI Card

1 release tab 2 card retention latch 3 card

4 card-edge connector 5 card connector

Page 31 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card
Page 31 · click to enlarge
Page 31
6. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.
Dell Desktop Computer (DCCY) — Removing a PCI Card diagram (page 31)
Fig. 13 · Removing a PCI Card

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

7. Secure the card(s) by closing the card retention latch and snapping it into place.
8. Connect any cables that should be attached to the card. 9. Replace the computer cover (see Replacing the Computer Cover ).
10. If you installed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).

11. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 12. Install any drivers required for the card as described in the card documentation.

Removing a PCI Card

1. Follow the procedures in Before You Begin .
2. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 3. If necessary, disconnect any cables connected to the card. 4. Grasp the card by its top corners, and ease it out of its connector.
Page 32 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Card in the Riser-Card Cage
Page 32 · click to enlarge
Page 32
Dell Desktop Computer (DCCY) — Installing a PCI Card in the Riser-Card Cage diagram (page 32)
Fig. 14 · Installing a PCI Card in the Riser-Card Cage

1 release tab 2 card retention latch 3 card

4 card-edge connector 5 card connector

5. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
6. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

7. Secure any remaining card(s) by closing the card retention latch and snapping it into place. 8. Replace the computer cover (see Replacing the Computer Cover ). 9. Uninstall the card's driver. See the documentation that came with the card for instructions. 10. If you removed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.

11. If you removed an network-adapter card connector:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

Installing a PCI Card in the Riser-Card Cage

1. Follow the procedures in Before You Begin . 2. If applicable, remove the card installed in the PCI3 connector on the system board (see Removing a PCI Card ). 3. Remove the riser-card cage:

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.

Page 33 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Card in the Riser-Card Cage
Page 33 · click to enlarge
Page 33
Dell Desktop Computer (DCCY) — Installing a PCI Card in the Riser-Card Cage diagram (page 33)
Fig. 15 · Installing a PCI Card in the Riser-Card Cage

1 riser-card cage 2 handle

4. If you are installing a new card, remove the filler bracket to create an empty card-slot opening. 5. If you are replacing a card that is already installed in the computer, remove the card. 6. If necessary, disconnect any cables connected to the card. 7. Grasp the card by its corners, and ease it out of its connector.
8. Prepare the new card for installation.
9. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position.
Dell Desktop Computer (DCCY) — Installing a PCI Card in the Riser-Card Cage diagram (page 33)
Fig. 16 · Installing a PCI Card in the Riser-Card Cage

1 release tab 2 card retention latch 3 card

4 card-edge connector 5 card connector

10. Insert the card firmly into the card connector on the riser-card cage. 11. Secure the card(s) by closing the card retention latch and snapping it into place. 12. Replace the riser-card cage:
Page 34 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 34 · click to enlarge
Page 34

a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 34)
Fig. 17 · Removing a PCI Card From the Riser-Card Cage

1 riser-card cage 2 slots 3 riser cards (2)

4 system board connectors (2)

13. Reconnect any cables that you removed in step 3 .
14. Connect any cables that should be attached to the card. 15. Replace the computer cover (see Replacing the Computer Cover ). 16. If you installed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).

17. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 18. Install any drivers required for the card as described in the card documentation.

Removing a PCI Card From the Riser-Card Cage

1. Follow the procedures in Before You Begin . 2. Remove the riser-card cage:

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.

Page 35 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 35 · click to enlarge
Page 35
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 35)
Fig. 18 · Removing a PCI Card From the Riser-Card Cage

1 riser-card cage 2 handle

3. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 4. If necessary, disconnect any cables connected to the card. 5. Grasp the card by its top corners, and ease it out of its connector. 6. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
7. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

8. Secure any remaining card(s) by closing the card retention latch and snapping it into place. 9. Replace the riser-card cage:

a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 35)
Fig. 19 · Removing a PCI Card From the Riser-Card Cage

1 riser-card cage 2 slots 3 riser cards (2)

4 system board connectors (2)

10. Replace the computer cover (see Replacing the Computer Cover ).
Page 36 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Express x16 Card or DVI-Card
Page 36 · click to enlarge
Page 36
11. Uninstall the card's driver. See the documentation that came with the card for instructions. 12. If you removed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.

13. If you removed a network-adapter card connector:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

PCI Express and DVI Cards

Your computer supports one low-profile PCI Express x16 card. If your computer contains a riser-card cage, you can not install a PCI Express DVI card because the riser-card cage blocks the DVI-card (DVI_HDR) connector on the system board.

If you are replacing a PCI Express card with a different type of PCI Express card, remove the current driver for the card from the operating system. See the documentation that came with the card for information.

Installing a PCI Express x16 Card or DVI-Card

1. Follow the procedures in Before You Begin .

2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open. 3. If you are installing a new PCI Express x16 card or DVI-card, remove the filler bracket to create a card-slot opening. Then continue with step 5. 4. If you are replacing a PCI Express x16 card or DVI-card, remove the installed card (see Removing a PCI Express x16 Card or DVI-Card). If necessary, disconnect any cables connected to the card. Then continue with step 6. 5. Prepare the card for installation.

Dell Desktop Computer (DCCY) — Installing a PCI Express x16 Card or DVI-Card diagram (page 36)
Fig. 20 · Installing a PCI Express x16 Card or DVI-Card

1 release tab 2 card retention latch 3 card

4 card-edge connector 5 card connector

6. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.
Page 37 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 37 · click to enlarge
Page 37
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 37)
Fig. 21 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x16 or DVI card 2 PCI Express x16 card connector

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 37)
Fig. 22 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x16 card 2 DVI card connector 3 PCI Express x16 card connector

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

7. Connect any cables that should be attached to the card. 8. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

9. Secure the card(s) by closing the card retention latch and snapping it into place. 10. Replace the computer cover (see Replacing the Computer Cover ).
Page 38 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Express x16 Card or DVI-Card
Page 38 · click to enlarge
Page 38
11. If you installed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).

12. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 13. Install any drivers required for the card as described in the card documentation.

Removing a PCI Express x16 Card or DVI-Card

1. Follow the procedures in Before You Begin . 2. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 3. If necessary, disconnect any cables connected to the card. 4. Press the lever with your thumb until you release the securing tab.

If you are removing a PCI Express x16 card, go to step 5.

If you are removing a DVI card, go to step 6

5. While pressing the lever, pull the card up and out of the card connector.
Dell Desktop Computer (DCCY) — Removing a PCI Express x16 Card or DVI-Card diagram (page 38)
Fig. 23 · Removing a PCI Express x16 Card or DVI-Card

1 PCI Express x16 card 2 lever 3 securing slot (not all cards)

4 securing tab 5 PCI Express x16 card connector

6. While pressing the lever, pull the removal pull tab up and remove the card out of the card connector.
Page 39 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Express Card in the Riser-Card Cage
Page 39 · click to enlarge
Page 39
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 39)
Fig. 24 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x16 DVI-card 2 removal pull tab 3 DVI card connector

4 lever 5 securing slot 6 securing tab

7 PCI Express x16 card connector

7. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
8. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

9. Secure any remaining card(s) by closing the card retention latch and snapping it into place.
10. Replace the computer cover (see Replacing the Computer Cover ).
11. Uninstall the card's driver. See the documentation that came with the card for instructions. 12. If you removed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.

13. If you removed a network-adapter card:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

Installing a PCI Express Card in the Riser-Card Cage

1. Follow the procedures in Before You Begin . 2. If applicable, remove the card installed in the PCI3 connector on the system board (see Removing a PCI Card ). 3. Remove the riser-card cage:

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage up and gently pull on the handle and lift the riser-card cage up and away from the computer.

Page 40 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 40 · click to enlarge
Page 40
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 40)
Fig. 25 · Removing a PCI Card From the Riser-Card Cage

1 riser-card cage 2 handle

4. If you are installing a new card, remove the filler bracket to create an empty card-slot opening.

If you are replacing a card that is already installed in the computer, remove the card. If necessary, disconnect any cables connected to the card. Grasp the card by its corners, and ease it out of its connector.

5. Prepare the new card for installation.
6. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position.

1 release tab 2 card retention latch 3 card

4 card-edge connector 5 card connector

7. Insert the card firmly into the card connector on the riser-card cage.
Page 41 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 41 · click to enlarge
Page 41
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 41)
Fig. 26 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x16 card 2 PCI Express x16 card connector

8. Secure the card(s) by closing the card retention latch and snapping it into place. 9. Replace the riser-card cage:

a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 41)
Fig. 27 · Removing a PCI Card From the Riser-Card Cage

1 riser-card cage 2 slots 3 riser cards (2)

4 system board connectors (2)

10. Reconnect any cables that you removed in step 3 . 11. Connect any cables that should be attached to the card. 12. Replace the computer cover (see Replacing the Computer Cover ). 13. If you installed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).

14. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 15. Install any drivers required for the card as described in the card documentation.

Page 42 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Express Card From the Riser-Card Cage
Page 42 · click to enlarge
Page 42

Removing a PCI Express Card From the Riser-Card Cage

1. Follow the procedures in Before You Begin . 2. Remove the riser-card cage:

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.

Dell Desktop Computer (DCCY) — Removing a PCI Express Card From the Riser-Card Cage diagram (page 42)
Fig. 28 · Removing a PCI Express Card From the Riser-Card Cage

1 riser-card cage 2 handle

3. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 4. If necessary, disconnect any cables connected to the card. 5. Press the lever with your thumb until you release the securing tab. 6. While pressing the lever, pull the card up and out of the card connector.

1 PCI Express x16 card 2 lever 3 securing slot (not all cards)

4 securing tab 5 PCI Express x16 card connector

7. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
8. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

9. Secure any remaining card(s) by closing the card retention latch and snapping it into place.
Page 43 of the Dell Desktop Computer (DCCY) user manual — Installing a PS/2 Serial Port Adapter
Page 43 · click to enlarge
Page 43
10. Replace the riser-card cage:

a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 43)
Fig. 29 · Removing a PCI Card From the Riser-Card Cage

1 riser-card cage 2 slots 3 riser cards (2)

4 system board connectors (2)

11. Replace the computer cover (see Replacing the Computer Cover ). 12. Uninstall the card's driver. See the documentation that came with the card for instructions. 13. If you removed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.

14. If you removed a network-adapter card connector:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

PS/2 Serial Port Adapters

Installing a PS/2 Serial Port Adapter

1. Follow the procedures in Before You Begin . 2. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 3. Remove the filler bracket (if applicable).
4. Align the PS/2 serial-port adapter bracket in the retention slot and press down firmly. Ensure that the adapter is fully seated in the slot.
Page 44 of the Dell Desktop Computer (DCCY) user manual — Removing a PS/2 Serial Port Adapter
Page 44 · click to enlarge
Page 44
5. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

6. Secure the card(s) by closing the card retention latch and snapping it into place.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 44)
Fig. 30 · Removing a PCI Card From the Riser-Card Cage

1 release tab 2 adapter retention latch 3 serial-port adapter bracket

4 serial port adapter connector

5 serial port adapter system board connector (PS2/SER2)

7. Connect the adapter cable to the PS/2 serial port adapter connector (PS2/SER2) on the system board (see System Board Components ).
8. Replace the computer cover (see Replacing the Computer Cover ).

Removing a PS/2 Serial Port Adapter

1. Follow the procedures in Before You Begin. 2. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 3. Disconnect the PS/2 serial-port cable from the system board (see System Board Components). 4. Grasp the PS/2 serial-port adapter bracket by its top corners, and ease it out of its connector. 5. If you are removing the adapter permanently, install a filler bracket in the empty card-slot opening.

6. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

7. Secure any remaining card(s) by closing the card retention latch and snapping it into place. 8. Replace the computer cover (see Replacing the Computer Cover ).
Page 45 of the Dell Desktop Computer (DCCY) user manual — Installing a Serial Port Adapter in the Riser-Card Cage
Page 45 · click to enlarge
Page 45

Installing a Serial Port Adapter in the Riser-Card Cage

1. Follow the procedures in Before You Begin . 2. Remove the riser-card cage:

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.

Dell Desktop Computer (DCCY) — Installing a Serial Port Adapter in the Riser-Card Cage diagram (page 45)
Fig. 31 · Installing a Serial Port Adapter in the Riser-Card C…

1 riser-card cage 2 handle 3 riser cards (2)

3. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 4. If you are installing a new serial port adapter, remove the filler bracket to create an empty card-slot opening. 5. If you are replacing an adapter that is already installed in the computer, remove the adapter. 6. If necessary, disconnect any cables connected to the adapter. 7. Grasp the serial port adapter by its top corners, and ease it out of its connector. 8. Prepare the serial port adapter for installation.

9. Align the PS/2 serial-port adapter bracket in the retention slot and press down firmly. Ensure that the adapter is fully seated in the slot. 10. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

11. Secure the card(s) by closing the card retention latch and snapping it into place.
12. Connect the adapter cable to the PS/2 serial port adapter connector (PS2/SER2) on the system board (see System Board Components ). 13. Replace the riser-card cage:

a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position. 14. Connect any disconnected cables. 15. Replace the computer cover (see Replacing the Computer Cover).

Page 46 of the Dell Desktop Computer (DCCY) user manual — Removing a Serial Port Adapter From the Riser-Card Cage
Page 46 · click to enlarge
Page 46
16. Install any drivers required for the serial port adapter.

Removing a Serial Port Adapter From the Riser-Card Cage

1. Follow the procedures in Before You Begin . 2. Remove the riser-card cage:

a. Check any cables connected to cards through the back-panel openings. Disconnect any cables that will not reach the riser-card cage once they are removed from the computer. b. Rotate the riser-card cage handle up and gently pull on the handle and lift the riser-card cage up and away from the computer.

Dell Desktop Computer (DCCY) — Removing a Serial Port Adapter From the Riser-Card Cage diagram (page 46)
Fig. 32 · Removing a Serial Port Adapter From the Riser-Card C…

1 riser-card cage 2 handle 3 riser cards (2)

3. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 4. Disconnect the PS/2 serial-port cable from the system board (see System Board Components ). 5. Grasp the PS/2 serial-port adapter bracket by its top corners, and ease it out of its connector. 6. If you are removing the adapter permanently, install a filler bracket in the empty card-slot opening.
7. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

8. Secure the card(s) by closing the card retention latch and snapping it into place. 9. Replace the riser-card cage:

a. Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place. b. Ensure that the riser-card connectors are fully seated in the connectors on the system board. c. Rotate the riser-card cage handle to the down position. 10. Replace the computer cover (see Replacing the Computer Cover). 11. Uninstall the adapter's driver. See the documentation that came with the adapter for instructions.

Page 47 of the Dell Desktop Computer (DCCY) user manual — Removing the Processor
Page 47 · click to enlarge
Page 47

Dell™ Optiplex™ 740 Systems User's Guide

Processor

Removing the Processor

1. Follow the procedures in Before You Begin . 2. Loosen the captive screw on each side of the heat sink assembly.
3. Rotate the heat sink assembly upward, and remove the assembly from the computer.

Lay the heat sink assembly down on its top, with the thermal grease facing upward.

Dell Desktop Computer (DCCY) — Removing the Processor diagram (page 47)
Fig. 33 · Removing the Processor

1 heat sink assembly 2 captive screw housing (2)

4. Pull the release lever straight up until the processor is released.

Processor

Page 48 of the Dell Desktop Computer (DCCY) user manual — Installing the Processor
Page 48 · click to enlarge
Page 48
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 48)
Fig. 34 · Removing a PCI Card From the Riser-Card Cage

1 processor 2 release lever 3 socket

5. Remove the processor from the socket.

Leave the release lever extended in the release position so that the socket is ready for the new processor, and go to Installing the Processor.

Installing the Processor

1. Follow the procedures in Before You Begin .
2. Unpack the new processor, being careful not to bend any of the processor pins.
3. If the release lever on the socket is not fully extended, move it to that position. 4. Align the pin-1 corners of the processor and socket.
Page 49 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 49 · click to enlarge
Page 49
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 49)
Fig. 35 · Removing a PCI Card From the Riser-Card Cage

1 socket and processor pin-1 indicator 2 processor 3 release lever

5. Set the processor lightly in the socket and ensure that the processor is positioned correctly. 6. While lightly pressing down on the processor, rotate the release lever back toward the system board until it snaps into place, securing the processor. 7. Clean the thermal grease from the bottom of the heat sink.
8. Apply the new thermal grease to the top of the processor. 9. Install the heat sink assembly:

a. Place the heat sink assembly back onto the heat-sink assembly bracket. b. Rotate the heat sink assembly down towards the computer base and ensure that the two captive screws are properly aligned with the holes in the system board. c. Tighten the two captive screws.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 49)
Fig. 36 · Removing a PCI Card From the Riser-Card Cage

1 heat sink assembly 2 heat-sink assembly bracket 3 captive screw housing (2)

10. Replace the computer cover (see Replacing the Computer Cover ).

4 processor socket

Page 50 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 50 · click to enlarge
Page 50
Page 50 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 51 of the Dell Desktop Computer (DCCY) user manual — Power Cable Connectors
Page 51 · click to enlarge
Page 51

Drives

Your computer supports:

l One SATA hard drive

l One optional floppy drive or media card reader or one second SATA hard drive

l One optional optical (CD or DVD) drive

Dell Desktop Computer (DCCY) — Drives diagram (page 51)
Fig. 37 · Drives

1 optical drive 2 floppy drive or media card reader or SATA hard drive 3 hard drive

General Installation Guidelines

Connect the SATA hard drive to the connector labeled "SATA0." Connect the SATA CD or DVD drives to the connector labeled "SATA1" on the system board. Connect a second optional hard drive to the connector labeled "SATA2." See System Board Components for information about system board connectors.

Connecting Drive Cables

When you install a drive, you connect two cables—a DC power cable and a data cable—to the back of the drive and to the system board.

Drive Interface Connectors

1 interface cable connector 2 interface connector

Interface connectors are keyed for correct insertion.

Power Cable Connectors

Drives · Serial ATA Connector

Page 52 of the Dell Desktop Computer (DCCY) user manual — Removing an Optical Drive
Page 52 · click to enlarge
Page 52

Serial ATA Power Connector

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 52)
Fig. 38 · Removing a PCI Card From the Riser-Card Cage

1 power cable 2 power input connector

Connecting and Disconnecting Drive Cables

When connecting and disconnecting a SATA data cable, hold the cable by the black connector at each end.

Dell Desktop Computer (DCCY) — Connecting and Disconnecting Drive Cables diagram (page 52)
Fig. 39 · Connecting and Disconnecting Drive Cables

Optical Drive

Removing an Optical Drive

1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover).
3. Pull up on the drive release latch and slide the drive towards the back of the computer. Then lift up to remove the drive from the computer.
Dell Desktop Computer (DCCY) — Removing an Optical Drive diagram (page 52)
Fig. 40 · Removing an Optical Drive
Page 53 of the Dell Desktop Computer (DCCY) user manual — Installing an Optical Drive
Page 53 · click to enlarge
Page 53

1 drive release latch

4. Disconnect the power and data cables from the back of the drive. 5. If you are not replacing the optical drive at this time, install the optical drive insert by lowering it into the drive bay until it clicks into place. Contact Dell if you need a drive bay insert.

Installing an Optical Drive

1. Unpack the drive and prepare it for installation.

Check the documentation that accompanied the drive to verify that the drive is configured for your computer.

2. Pull up on the drive-release latch and slide the drive towards the back of the computer. Then, lift up to remove the drive from the computer. 3. If you are installing a new drive:

a. Remove the inserts. b. Insert the three shoulder screws removed from the insert into the sides of the new drive and tighten them. c. Lift the drive release latch up and insert the new optical device. 4. If you are replacing an existing drive:

a. Follow procedures in Removing an Optical Drive to remove the existing drive. b. Remove the three shoulder screws from the existing drive. c. Insert the three shoulder screws into the sides of the new drive and tighten them.

Dell Desktop Computer (DCCY) — Installing an Optical Drive diagram (page 53)
Fig. 41 · Installing an Optical Drive
5. Connect the power and data cables to the drive. 6. Align the shoulder screws with the screw guides, and slide the drive into the bay until it clicks into place.
Dell Desktop Computer (DCCY) — Installing an Optical Drive diagram (page 53)
Fig. 42 · Installing an Optical Drive
7. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents.

2 optical drive

Page 54 of the Dell Desktop Computer (DCCY) user manual — Installing a Floppy Drive
Page 54 · click to enlarge
Page 54
8. Replace the computer cover (see Replacing the Computer Cover). 9. Update your configuration information by setting the appropriate Drive option ( 0 or 1 ) under Drives . See Entering System Setup for more information. 10. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics ).

Floppy Drive

Removing a Floppy Drive

1. Follow the procedures in Before You Begin .
2. Remove the optical drive (see Removing an Optical Drive ) and carefully set it aside.
3. Pull up on the drive release latch and slide the floppy drive towards the back of the computer. Then, lift up to remove the drive from the computer.
Dell Desktop Computer (DCCY) — Removing a Floppy Drive diagram (page 54)
Fig. 43 · Removing a Floppy Drive

1 drive release latch 2 floppy drive

4. Disconnect the power and data cables from the back of the floppy drive.

Installing a Floppy Drive

1. If you are installing a new drive:

a. Use a small flat-edge screw driver on the back side of the drive-panel insert to gently pop off the insert. b. Remove the four shoulder screws from the drive-panel insert. 2. If you are replacing an existing drive:

Remove the four shoulder screws from the existing drive.

3. Insert the four shoulder screws into the sides of the new floppy drive and tighten them.
Page 55 of the Dell Desktop Computer (DCCY) user manual — Removing the Media Card Reader
Page 55 · click to enlarge
Page 55
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 55)
Fig. 44 · Removing a PCI Card From the Riser-Card Cage
4. Attach the power and floppy-drive cables to the floppy drive. 5. Connect the floppy drive cable to the DSKT connector on the system board (see System Board Components for the connector locations). 6. Align the shoulder screws with the screw guides, and slide the drive into the bay until it clicks into place.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 55)
Fig. 45 · Removing a PCI Card From the Riser-Card Cage

1 floppy drive 2 slot verification number

7. Replace the optical drive (see Installing an Optical Drive). 8. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 9. Replace the computer cover (see Replacing the Computer Cover ). 10. Enter system setup and set the Diskette Drive option to enable your new floppy drive (see Entering System Setup ). 11. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics ).

Media Card Reader

Removing the Media Card Reader

1. Follow the procedures in Before You Begin .
2. Remove the optical drive (see Removing an Optical Drive ) and carefully set it aside.
Page 56 of the Dell Desktop Computer (DCCY) user manual — Installing the Media Card Reader
Page 56 · click to enlarge
Page 56
3. Pull up on the drive release latch and slide the media card reader towards the back of the computer. Then, lift up to remove the media card reader from the computer. 4. Disconnect the media card reader cable from the back of the media card reader.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 56)
Fig. 46 · Removing a PCI Card From the Riser-Card Cage

1 media card reader 2 drive release latch 3 media card reader cable

Installing the Media Card Reader

1. If you are installing a new media card reader:

a. Use a small flat-edge screw driver on the back side of the drive-panel insert to gently pop off the insert. b. Remove the four shoulder screws from the drive-panel insert. 2. If you are replacing an existing media card reader:

Remove the four shoulder screws from the existing media card reader.

3. Insert the four shoulder screws into the sides of the new media card reader and tighten them.
Dell Desktop Computer (DCCY) — Installing the Media Card Reader diagram (page 56)
Fig. 47 · Installing the Media Card Reader
4. Attach the media card reader cable to the media card reader. 5. Connect the card reader cable to the USB1 connector on the system board (see System Board Components for the connector location). 6. Align the shoulder screws with the screw guides numbered as 2, and slide the media card reader forward into the bay until it clicks into place.
Page 57 of the Dell Desktop Computer (DCCY) user manual — Removing the Hard Drive
Page 57 · click to enlarge
Page 57
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 57)
Fig. 48 · Removing a PCI Card From the Riser-Card Cage

1 media card reader 2 shoulder screws (4) 3 media card reader cable

4 shoulder screw slots (2)

7. Replace the optical drive (see Installing an Optical Drive ). 8. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 9. Replace the computer cover (see Replacing the Computer Cover ). 10. Enter system setup and set the Diskette Drive option to enable your new media card reader (see Entering System Setup ). 11. Verify that your computer works correctly by running theDell Diagnostics (see Dell Diagnostics ).

Hard Drive

Removing the Hard Drive

1. If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. 2. Follow the procedures in Before You Begin .

3. Remove the optical drive (see Removing an Optical Drive) from the bay and carefully set it aside. 4. Remove the floppy drive, media card reader, or second hard drive, if installed, (see Removing a Floppy Drive, Removing the Media Card Reader, or Removing and Replacing a Second Hard Drive) and carefully set it aside. 5. Squeeze the two plastic securing clips on each side of the hard drive and slide the drive towards the back of the computer.

Page 58 of the Dell Desktop Computer (DCCY) user manual — Installing a Hard Drive
Page 58 · click to enlarge
Page 58
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 58)
Fig. 49 · Removing a PCI Card From the Riser-Card Cage

1 securing clips (2) 2 hard drive

6. Lift the drive out of the computer and disconnect the power and hard-drive cables from the drive.

Installing a Hard Drive

1. Unpack the replacement hard drive, and prepare it for installation.
2. If your replacement hard drive does not have the plastic hard-drive bracket attached, remove the bracket from the existing drive by unsnapping it from the drive.
Dell Desktop Computer (DCCY) — Installing a Hard Drive diagram (page 58)
Fig. 50 · Installing a Hard Drive

1 hard drive 2 release tabs (2) 3 plastic hard-drive bracket

3. Attach the bracket to the new drive by aligning the two securing tabs with the mounting holes in the hard drive and then rotating the drive down, snapping it onto the bracket
Dell Desktop Computer (DCCY) — Installing a Hard Drive diagram (page 58)
Fig. 51 · Installing a Hard Drive

1 securing tabs (2) 2 drive 3 release tabs (2)

4 plastic hard-drive bracket

Page 59 of the Dell Desktop Computer (DCCY) user manual — Removing and Replacing a Second Hard Drive
Page 59 · click to enlarge
Page 59
4. Connect the power and data cables to the drive. 5. Locate the correct slot for the drive, and slide the drive into the bay until it clicks into place.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 59)
Fig. 52 · Removing a PCI Card From the Riser-Card Cage

1 hard drive 2 slot verification number

6. Replace the floppy drive, media card reader, or second hard drive (see Installing a Floppy Drive, Installing the Media Card Reader, or Removing and Replacing a Second Hard Drive). 7. Replace the optical drive (see Installing an Optical Drive). 8. Check all connectors to be certain that they are properly cabled and firmly seated. 9. Replace the computer cover (see Replacing the Computer Cover). 10. If the drive you just installed is the primary drive, insert a bootable medium into your boot drive. 11. Turn on the computer. 12. Enter system setup and update the appropriate Primary Drive option (0 or 2) (see Entering System Setup). 13. Exit system setup, and reboot the computer. 14. Partition and logically format your drive before you proceed to the next step.

For instructions, see the documentation that came with your operating system.

15. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics ). 16. Install your operating system on the hard drive.

For instructions, see the documentation that came with your operating system.

Removing and Replacing a Second Hard Drive

For information on RAID configuration, see About RAID Configurations

Page 60 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 60 · click to enlarge
Page 60
1. Check the documentation or the drive to verify that it is configured for your computer. 2. Follow the procedures in Before You Begin. 3. Remove the computer cover (see Removing the Computer Cover). 4. Remove the optical drive (if your configuration has one) (see Removing an Optical Drive ). 5. To remove the second hard drive:

a. Pull up on the drive release latch and slide the hard drive towards the back of the computer. b. Disconnect the data and power cables from the back of the drive. c. Then, lift up to remove the drive from the computer. 6. To replace the second hard drive:

a. Align the shoulder screws with the screw guides, and slide the drive into the bay until it clicks into place. b. Connect the power and data cables to the back of the drive.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 60)
Fig. 53 · Removing a PCI Card From the Riser-Card Cage
7. Ensure that the data cable from the second hard drive remains connected to the SATA1 connector on the system board.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 60)
Fig. 54 · Removing a PCI Card From the Riser-Card Cage

1 data cable 2 hard drive system board connector

8. Replace the optical drive (if your configuration has one). See Installing an Optical Drive . 9. Replace the computer cover (see Replacing the Computer Cover). 10. Turn on the computer.
Page 61 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 61 · click to enlarge
Page 61
11. If you have installed a replacement second hard drive, complete step 12 through step 16 . 12. Enter system setup, and update the SATA port option under the Drives option list (see Entering System Setup ). 13. Exit system setup, and reboot the computer. 14. Partition and logically format your drive.
15. Test the hard drive by running the Dell Diagnostics (see Dell Diagnostics ). 16. Install your operating system on the (new) second hard drive.
Page 62 of the Dell Desktop Computer (DCCY) user manual — Notes, Notices, and Cautions
Page 62 · click to enlarge
Page 62

Dell™ OptiPlex™ 740 User's Guide

Desktop Computer

About Your Computer Finding Information Desktop Computer Desktop Computer (Model # DCNE) Specifications Advanced Features Cleaning Your Computer Reinstalling Drivers and the Operating System Solving Problems Microsoft® Windows® XP and Windows Vista® Features Troubleshooting Tools and Utilities Getting Help Warranty FCC Regulatory Model (U.S. Only) Glossary

Removing and Replacing Parts Before You Begin Removing the Computer Cover Chassis Intrusion Switch I/O Panel Drives PCI, PCI Express Cards, and PS/2 Serial Port Adapters Power Supply Processor Battery Replacing the System Board Memory Replacing the Computer Cover

ModelsDCSM, DCNE, and DCCY

Notes, Notices, and Cautions

Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, OptiPlex, Inspiron, Dimension, Latitude, Dell Precision, DellNet, TravelLite, Dell OpenManage, PowerVault, Axim, PowerEdge, PowerConnect, and PowerApp are trademarks of Dell Inc.; AMD, AMD Athlon, AMD Phenom, and combinations thereof, and Cool 'n' Quiet are trademarks of Advanced Micro Devices, Inc; Microsoft and Windows are registered trademarks of Microsoft Corporation; IBM is a registered trademark of International Business Machines Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

March 2008 RP699 Rev. A03

Page 63 of the Dell Desktop Computer (DCCY) user manual — Replacing the I/O Panel
Page 63 · click to enlarge
Page 63

I/O Panel

Removing the I/O Panel

1. Follow the procedures in Before You Begin . 2. Remove the cable from the I/O panel by pulling on the pull-loop. 3. Remove the screw that secures the I/O panel to the desktop computer.
4. Gently rotate and slide the I/O panel away from the computer.
Dell Desktop Computer (DCCY) — I/O Panel diagram (page 63)
Fig. 55 · I/O Panel

1 securing screw 2 I/O panel 3 I/O cable connector

4 I/O connector pull loop

Replacing the I/O Panel

1. To replace the I/O panel, follow the removal procedures in the reverse order.

I/O Panel

Page 64 of the Dell Desktop Computer (DCCY) user manual — Power Supply
Page 64 · click to enlarge
Page 64

Power Supply

Replacing the Power Supply

1. Follow the procedures in Before You Begin . 2. Disconnect the DC power cables from the system board and the drives.
3. Remove the two screws that attach the power supply to the back of the computer chassis. 4. Remove the optical drive and carefully set it aside (see Removing an Optical Drive). 5. Press the release button located on the floor of the computer chassis.
Dell Desktop Computer (DCCY) — Power Supply diagram (page 64)
Fig. 56 · Power Supply

1 power supply 2 release button 3 screws (2)

4 AC power connector

6. Slide the power supply toward the front of the computer by approximately 1 inch. 7. Lift the power supply up and out of the computer. 8. Slide the replacement power supply into place. 9. Replace the screws that secure the power supply to the back of the computer chassis. 10. Reconnect the DC power cables (see System Board Components for connector locations). 11. Replace the optical drive (see Installing an Optical Drive ).

Power Supply

Page 65 of the Dell Desktop Computer (DCCY) user manual — DC Power Connector P1
Page 65 · click to enlarge
Page 65
12. Replace the computer cover (see Replacing the Computer Cover ). 13. Connect the AC power cable to the AC power connector.

DC Power Connectors

Dell Desktop Computer (DCCY) — DC Power Connectors diagram (page 65)
Fig. 57 · DC Power Connectors

DC Power Connector P1

Dell Desktop Computer (DCCY) — DC Power Connector P1 diagram (page 65)
Fig. 58 · DC Power Connector P1
Dell Desktop Computer (DCCY) — DC Power Connector P1 diagram (page 65)
Fig. 59 · DC Power Connector P1
Page 66 of the Dell Desktop Computer (DCCY) user manual — DC Power Connector P5 and P6
Page 66 · click to enlarge
Page 66

*Use 22-AWG wire instead of 18-AWG wire.

DC Power Connector P2

Dell Desktop Computer (DCCY) — DC Power Connector P2 diagram (page 66)
Fig. 60 · DC Power Connector P2

DC Power Connector P3

Dell Desktop Computer (DCCY) — DC Power Connector P3 diagram (page 66)
Fig. 61 · DC Power Connector P3

DC Power Connector P4

Dell Desktop Computer (DCCY) — DC Power Connector P4 diagram (page 66)
Fig. 62 · DC Power Connector P4

DC Power Connector P5 and P6

Dell Desktop Computer (DCCY) — DC Power Connector P5 and P6 diagram (page 66)
Fig. 63 · DC Power Connector P5 and P6
Page 67 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 67 · click to enlarge
Page 67
Page 67 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 68 of the Dell Desktop Computer (DCCY) user manual — Removing the Computer Cover
Page 68 · click to enlarge
Page 68

Dell™ Optiplex™ 740 Systems User's Guide

Removing the Computer Cover

Removing the Computer Cover

1. Follow the procedures in Before You Begin . 2. If you have installed a padlock through the padlock ring on the back panel, remove the padlock. 3. Locate the cover release latch shown in the illustration. Then, slide the release latch back as you lift the cover.
Dell Desktop Computer (DCCY) — Removing the Computer Cover diagram (page 68)
Fig. 64 · Removing the Computer Cover

1 security cable slot 2 cover release latch 3 padlock ring

4. Grip the sides of the computer cover and pivot the cover up using the hinge tabs as leverage points. 5. Remove the cover from the hinge tabs and set it aside on a soft nonabrasive surface.
Page 69 of the Dell Desktop Computer (DCCY) user manual — Desktop Computer (Model # DCNE) Specifications
Page 69 · click to enlarge
Page 69

Dell™ Optiplex™ 740 Systems User's Guide

Desktop Computer (Model # DCNE) Specifications

Desktop Computer (Model # DCNE) Specifications

Microprocessor type AMD Phenom™ processors

AMD Athlon™ 64 X2 Dual-Core processor

Internal cache AMD Phenom Quad-Core2-MB L2 dedicated cache and 2-MB shared L3 cache
AMD Phenom Triple-Core1.5-MB L2 dedicated cache and 2-MB shared L3 cache
AMD Athlon 64 X22-MB L2 dedicated cache

AMD Athlon 64 X2:1-MB L2 dedicated cache

AMD Athlon1-MB L2 dedicated cache
AMD Athlon512-KB L2 dedicated cache

Type 533-, 667-, or 800-MHz DDR2 SDRAM

Memory modules supported 256 MB, 512 MB, 1 GB, or 2 GB non-ECC

Minimum memory dual-channel512 MB; single-channel: 256 MB

Maximum memory 8 GB

Chipset nVidia GeForce 6150LE/Nforce 430

RAID support RAID 0 and RAID 1

Data bus width 64 bits

Address bus width 40 bits

BIOS chip (NVRAM) 8 Mb or 4 Mb

Show 7 more labels / short text on this page
Microprocessor · AMD Athlon 64 · Memory · Memory connectors 4 · Computer Information · DMA channels eight · Interrupt levels 24
Page 70 of the Dell Desktop Computer (DCCY) user manual — PCI
Page 70 · click to enlarge
Page 70

NIC integrated network interface with ASF 1.03 and 2.0 support as defined by DMTF

Capable of 10/100/1000 communication

Type nVidia integrated video (DirectX 9.0c Shader Model 3.0 Graphics Processing Unit) or PCI Express x16 graphics card or DVI graphics card

Type Sigma Tel 9200 CODEC (2.1 Channel Audio)

Stereo conversion 24-bit analog-to-digital; 24-bit digital-to-analog

Drives SATA controller supporting two 3.5-inch devices (two 3.5-inch hard drives supported)

Bus type PCI 2.3 PCI Express 1.0A SATA 1.0A and 2.0 USB 2.0

Bus speed PCI: 133 MB/s PCI Express x16: 40 GB/s bidirectional speed SATA: 1.5 Gbps and 3.0 Gbps USB: 480 Mbps high speed, 12Mbps full speed, 1.2 Mbps low speed

Cards half-length, full-height cards supported with optional riser-card cage

Defaultno riser-card cage low-profile cards supported

PCI

card size low profile

connector size 124 pins

card size low profile

power 25 W maximum

connector size 164 pins (x16)

connector data width (maximum) 16 PCI Express lanes (x16)

Optionalfull-height PCI Express riser-card cage low-profile and full-height cards supported

Externally accessible one 3.5-inch drive one bay for optical drive or optional second hard drive, supporting up to two 3.5-inch hard drives

Internally accessible one bay for a 1-inch-high hard drive

External connectors:

Serial 9-pin connector; 16550C-compatible

Parallel 25-hole connector (bidirectional)

Video 15-hole VGA connector

Network adapter RJ45 connector

Show 12 more labels / short text on this page
Video · Audio · Controllers · Expansion Bus · connectors two · connector data width · 32 bits · (maximum) · PCI Express · connectors one x16 · Drives · Connectors
Page 71 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 71 · click to enlarge
Page 71

Optional PS/2 with secondary serial port adapter

Optional DVI 36-pin connector

USB two front-panel and five back-panel USB 2.0– compliant connectors

Audio two connectors for line-in and line-out; two front- panel connectors for headphones and microphone

System board connectors:

SATA three 7-pin connectors

Floppy drive 38-pin connector

Serial 24-pin connector for optional second serial port card

PCI 2.3 two 124-pin connectors

Internal USB 10-pin connector

Intrusion switch 3-pin connector

Memory modules four 240-pin connector

Power 12V 4-pin connector

Front panel 40-pin connector

in Microsoft® Windows® XP and Windows Vista®, brings up the Windows Security window; in MS-DOS® mode, restarts (reboots) the computer

or starts embedded system setup (during system start- up only)

starts the RAID setup menu if RAID is turned on in the system setup program

or displays a boot device menu that allows the user to enter a device for a single boot (during system start- up only) as well as options to run hard-drive and system diagnostics

Power control front panel — push button

Power light green light. Blinking green indicates a sleep mode; solid green indicates a power-on state.

amber light. Blinking amber indicates a problem with an installed device; solid amber indicates an internal power problem (see Power Problems).

Hard-drive access light front panel — green

Link light front panel — solid green light indicates network connection

Link integrity light (on integrated network adapter) rear panel — green light for 10-Mb operation; orange light for 100-Mb operation; yellow light for a 1000-Mb (1-Gb) operation

Activity light (on integrated network adapter) rear panel — yellow blinking light

Diagnostic lights front panel — Four lights on the front panel. See Diagnostic Lights.

Standby power light AUX_PWR on the system board

DC power supply:

Show 10 more labels / short text on this page
two 6-pin mini-DINs · Fan 5-pin connector · PCIe-X16 164-pin connector · Speaker 5-pin connector · Power 24-pin connector · Battery 2-pin socket · Key Combinations · Controls and Lights · Power · Wattage 280 W
Page 72 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 72 · click to enlarge
Page 72
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 72)
Fig. 65 · Removing a PCI Card From the Riser-Card Cage

Voltage manual selection power supplies — 90 to 135 V at 50/60 Hz; 180 to 265 V at 50/60 Hz

Operating 0.25 G at 3 to 200 Hz at 0.5 octave/min

Storage 0.5 G at 3 to 200 Hz at 1 octave/min

Operating bottom half-sine pulse with a change in velocity of 50.8 cm/sec (20 inches/sec)

Storage 27-G faired square wave with a velocity change of 508 cm/sec (200 inches/sec)

Operating –15.2 to 3048 m (–50 to 10,000 ft)

Storage –15.2 to 10,668 m (–50 to 35,000 ft)

Airborne contaminant level G2 or lower as defined by ISA-S71.04-1985

Page 73 of the Dell Desktop Computer (DCCY) user manual — Removing a Speaker
Page 73 · click to enlarge
Page 73

Dell™ Optiplex™ 740 Systems User's Guide

Speaker

Installing a Speaker

1. Follow the procedures in Before You Begin . 2. Remove the cover of your computer (see Removing the Computer Cover ). 3. Attach the speaker to the system fan in the chassis of the computer.
4. Connect the cables to the system board. 5. Replace the computer cover. 6. Turn on power to the computer.

Removing a Speaker

1. Follow the procedures in Before You Begin . 2. Remove the cover of your computer (see Removing the Computer Cover ). 3. Disconnect the cables from the system board. 4. Remove the speaker from the system fan in the chassis of the computer.
5. Replace the computer cover. 6. Turn on power to the computer.

Speaker

Page 74 of the Dell Desktop Computer (DCCY) user manual — Dell™ Optiplex™ 740 Systems User's Guide
Page 74 · click to enlarge
Page 74

FCC Regulatory Model (U.S. Only)

Dell™ Optiplex™ 740 Systems User's Guide

The following information is provided on the device or devices covered in this document in compliance with the FCC regulations:

l Product nameDell™ OptiPlex™ 740
l Model numbersDCNE, DCSM, and DCCY

l Company name:

Dell Inc. Worldwide Regulatory Compliance & Environmental Affairs One Dell Way Round Rock, TX 78682 USA 512-338-4400

Page 75 of the Dell Desktop Computer (DCCY) user manual — Service Tag and Microsoft ® Windows ® License
Page 75 · click to enlarge
Page 75

Finding Information

Dell™ Optiplex™ 740 Systems User's Guide

What Are You Looking For?

l A diagnostic program for my computer

Drivers and Utilities Media

l Drivers for my computer

l My device documentation

l Desktop System Software (DSS)

Documentation and drivers are already installed on your computer. You can use the Drivers and Utilities media to reinstall drivers (see Reinstalling Drivers and Utilities) or to run the Dell Diagnostics (see Dell Diagnostics).

Dell Desktop Computer (DCCY) — Drivers and Utilities Media diagram (page 75)
Fig. 66 · Drivers and Utilities Media

Readme files may be included on your media to provide last-minute updates about technical changes to your computer or advanced technical-reference material for technicians or experienced users.

l How to set up my computer

Quick Reference Guide

l Basic troubleshooting information

l How to run the Dell Diagnostics

l Error codes and diagnostic lights

l Tools and utilities

l Additional information about setting up my computer

l How to troubleshoot and solve problems

l How to remove and install parts

Dell Desktop Computer (DCCY) — Quick Reference Guide diagram (page 75)
Fig. 67 · Quick Reference Guide

Dell™ Product Information Guide

l Terms and Conditions (U.S. only)

Dell Desktop Computer (DCCY) — Dell™ Product Information Guide diagram (page 75)
Fig. 68 · Dell™ Product Information Guide

l End User License Agreement

l Service Tag and Express Service Code

Service Tag and Microsoft ® Windows ® License

l Microsoft Windows License Label

Show 5 more labels / short text on this page
Find It Here · l Warranty information · l Safety instructions · l Regulatory information · l Ergonomics information
Page 76 of the Dell Desktop Computer (DCCY) user manual — Dell Support Website — support.dell.com
Page 76 · click to enlarge
Page 76

located on your computer.

Your computer's Service Tag contains both a Service Tag number and an Express Service Code.

l Use the Service Tag to identify your computer when you use

support.dell.com or contact support.

l Enter the Express Service Code to direct your call when contacting support.

Use the product key on the Microsoft Windows License Label if you need to reinstall your operating system.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 76)
Fig. 69 · Removing a PCI Card From the Riser-Card Cage

l Use the product key on the License Label if you need to reinstall your

operating system.

l Solutions — Troubleshooting hints and tips, articles from

Dell Support Website — support.dell.com

technicians, online courses, and frequently asked questions

l Community — Online discussion with other Dell customers

l Upgrades — Upgrade information for components, such as

memory, the hard drive, and the operating system

l Customer Care — Contact information, service call and order

status, warranty, and repair information

l Service and support — Service call status and support history,

service contract, online discussions with technical support

l Dell Technical Update Service — Proactive e-mail notification of

software and hardware updates for your computer

l Reference — Computer documentation, details on my computer

configuration, product specifications, and white papers

l Downloads — Certified drivers, patches, and software updates

l Desktop System Software (DSS)— If you reinstall the operating

system for your computer, you should also reinstall the DSS utility. DSS provides critical updates for your operating system and support for Dell™ 3.5-inch USB floppy drives, AMD™ processors, optical drives, and USB devices. DSS is necessary for correct operation of your Dell computer. The software automatically detects your computer and operating system and installs the updates appropriate for your configuration.

To download Desktop System Software:

1. Go to support.dell.com and click Drivers and Downloads . 2. Click Select Model . 3. Select your product model and click Confirm , or enter a service tag and click Go . 4. Click System Utilities . 5. Click Desktop System Software under Dell - Utility , and click Download Now . 6. Click Run to run the driver, or Save to save the driver to your computer.
Page 77 of the Dell Desktop Computer (DCCY) user manual — Windows Help and Support
Page 77 · click to enlarge
Page 77

l Software upgrades and troubleshooting hints — Frequently asked

Dell Support 3

questions, hot topics, and general health of your computing environment

Dell Support 3 is an automated upgrade and notification system installed on your computer. This support provides real-time health scans of your computing environment, software updates, and relevant self-support information. Access Dell

Support 3 from the icon in the taskbar.

l How to find information about my computer and its components

Windows Welcome Center

l How to connect to the Internet

l How to add user accounts for different people

l How to transfer files and settings from another computer

The Windows Welcome Center automatically appears when you use the computer for the first time. You can choose to have it appear every time you start your computer by placing a check in the Run at startup checkbox. Another method of

accessing the Welcome Center is to click the Windows Vista Start button , and then click Welcome Center.

l How to use Microsoft Windows XP or Windows Vista®

Windows Help and Support

l How to work with programs and files

l How to personalize my desktop

Microsoft Windows XP:

1. Click the Start button and click Help and Support . 2. Either select one of the topics listed, or type a word or phrase that describes your problem into the Search box, click the arrow icon, and then click the topic that describes your problem. 3. Follow the instructions on the screen.

Microsoft Windows Vista:

1. Click the Windows Vista Start button , and then click Help and Support . 2. In Search Help , type a word or phrase that describes your problem, and then press or click the magnifying glass. 3. Click the topic that describes your problem. 4. Follow the instructions on the screen.

l Remote help with troubleshooting my computer DellConnect™ Service and Support

Dell associates can diagnose and repair your computer remotely over a broadband connection. To learn more and get started with DellConnect, go to support.dell.com and click Revolutionary remote help—DellConnect.

l How to reinstall my operating system Operating System Media

The operating system is already installed on your computer. To reinstall your operating system, use the Operating System media. See Reinstalling Microsoft® Windows Vista® and Windows® XP.

After you reinstall your operating system, use the optional Drivers and Utilities media to reinstall drivers for the devices that came with your computer.

Dell Desktop Computer (DCCY) — Windows Help and Support diagram (page 77)
Fig. 70 · Windows Help and Support

Your operating system product key label is located on your computer.

Page 78 of the Dell Desktop Computer (DCCY) user manual — Online Services
Page 78 · click to enlarge
Page 78

Getting Help

Dell™ Optiplex™ 740 Systems User's Guide

Problems With Your Order

Returning Items for Warranty Repair or Credit

Obtaining Assistance

1. Complete the procedures in Before You Begin . 2. Run the Dell Diagnostics (see Dell Diagnostics ). 3. Make a copy of the Diagnostics Checklist (see Diagnostics Checklist ) and fill it out. 4. Use Dell's extensive suite of online services available at Dell Support ( support.dell.com ) for help with installation and troubleshooting procedures. 5. If the preceding steps have not resolved the problem, contact Dell.

When prompted by Dell's automated telephone system, enter your Express Service Code to route the call directly to the proper support personnel. If you do not have an Express Service Code, open the Dell Accessories folder, double-click the Express Service Code icon, and follow the directions.

For instructions on using the support service, see Support Service.

Online Services

You can access Dell Support at support.dell.com. Select your region on the WELCOME TO DELL SUPPORT page, and fill in the requested details to access help tools and information.

You can contact Dell electronically using the following addresses:

l World Wide Web

www.dell.com/

www.dell.com/ap/ (Asian/Pacific countries only)

www.dell.com/jp (Japan only)

www.euro.dell.com (Europe only)

www.dell.com/la/ (Latin American and Caribbean countries)

www.dell.ca (Canada only)

l Anonymous file transfer protocol (FTP)

ftp.dell.com/

Log in as user: anonymous, and use your e-mail address as your password.

l Electronic Support Service

mobile_support@us.dell.com

support@us.dell.com

Show 4 more labels / short text on this page
Obtaining Assistance · Product Information · Before You Call · Contacting Dell
Page 79 of the Dell Desktop Computer (DCCY) user manual — Returning Items for Warranty Repair or Credit
Page 79 · click to enlarge
Page 79

la-techsupport@dell.com (Latin America and Caribbean countries only)

apsupport@dell.com (Asian/Pacific countries only)

support.jp.dell.com (Japan only)

support.euro.dell.com (Europe only)

l Electronic Quote Service

apmarketing@dell.com (Asian/Pacific countries only)

sales_canada@dell.com (Canada only)

AutoTech Service

Dell's automated support service—AutoTech—provides recorded answers to the questions most frequently asked by Dell customers about their portable and desktop computers.

When you call AutoTech, use your touch-tone telephone to select the subjects that correspond to your questions.

The AutoTech service is available 24 hours a day, 7 days a week. You can also access this service through the support service. For the telephone number to call for your region, see Contacting Dell.

Automated Order-Status Service

To check on the status of any Dell™ products that you have ordered, you can go to support.dell.com, or you can call the automated order-status service. A recording prompts you for the information needed to locate and report on your order. For the telephone number to call for your region, see Contacting Dell.

Support Service

Dell's support service is available 24 hours a day, 7 days a week, to answer your questions about Dell hardware. Our support staff uses computer-based diagnostics to provide fast, accurate answers.

To contact Dell's support service, see Obtaining Assistance and then call the number for your country as listed in Contacting Dell.

Problems With Your Order

If you have a problem with your order, such as missing parts, wrong parts, or incorrect billing, contact Dell for customer assistance. Have your invoice or packing slip handy when you call. For the telephone number to call for your region, see Contacting Dell.

Product Information

If you need information about additional products available from Dell, or if you would like to place an order, visit the Dell website at www.dell.com. For the telephone number to call for your region or to speak to a sales specialist, see Contacting Dell.

Returning Items for Warranty Repair or Credit

Prepare all items being returned, whether for repair or credit, as follows:

1. Call Dell to obtain a Return Material Authorization Number, and write it clearly and prominently on the outside of the box.

For the telephone number to call for your region, see Contacting Dell.

2. Include a copy of the invoice and a letter describing the reason for the return. 3. Include a copy of the Diagnostics Checklist (see Diagnostics Checklist), indicating the tests that you have run and any error messages reported by the Dell Diagnostics (see Dell Diagnostics). 4. Include any accessories that belong with the item(s) being returned (power cables, software floppy disks, guides, and so on) if the return is for credit. 5. Pack the equipment to be returned in the original (or equivalent) packing materials.

You are responsible for paying shipping expenses. You are also responsible for insuring any product returned, and you assume the risk of loss during shipment to Dell. Collect On Delivery (C.O.D.) packages are not accepted.

Page 80 of the Dell Desktop Computer (DCCY) user manual — Contacting Dell
Page 80 · click to enlarge
Page 80

Returns that are missing any of the preceding requirements will be refused at Dell's receiving dock and returned to you.

Before You Call

Remember to fill out the Diagnostics Checklist (see Diagnostics Checklist). If possible, turn on your computer before you call Dell for assistance and call from a telephone at or near the computer. You may be asked to type some commands at the keyboard, relay detailed information during operations, or try other troubleshooting steps possible only at the computer itself. Ensure that the computer documentation is available.

Name:

Date:

Address:

Phone number:

Service Tag (bar code on the back or bottom of the computer):

Express Service Code:

Return Material Authorization Number (if provided by Dell support technician):

Operating system and version:

Devices:

Expansion cards:

Are you connected to a network? Yes No

Network, version, and network adapter:

Programs and versions:

See your operating system documentation to determine the contents of the system's start-up files. If the computer is connected to a printer, print each file. Otherwise, record the contents of each file before calling Dell.

Error message, beep code, or diagnostic code:

Description of problem and troubleshooting procedures you performed:

Contacting Dell

For customers in the United States, call 800-WWW-DELL (800-999-3355).

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

1. Visit support.dell.com. 2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page. 3. Click Contact Us on the left side of the page. 4. Select the appropriate service or support link based on your need. 5. Choose the method of contacting Dell that is convenient for you.

Diagnostics Checklist

Page 81 of the Dell Desktop Computer (DCCY) user manual — B
Page 81 · click to enlarge
Page 81

Glossary

Terms in this Glossary are provided for informational purposes only and may or may not describe features included with your particular computer.

A

AC — alternating current — The form of electricity that powers your computer when you plug the AC adapter power cable in to an electrical outlet.

ACPI — advanced configuration and power interface — A power management specification that enables Microsoft® Windows® operating systems to put a computer in standby or hibernate mode to conserve the amount of electrical power allocated to each device attached to the computer.

AGP — accelerated graphics port — A dedicated graphics port that allows system memory to be used for video-related tasks. AGP delivers a smooth, true-color video image because of the faster interface between the video circuitry and the computer memory.

AHCI — Advanced Host Controller Interface — An interface for a SATA hard drive Host Controller which allows the storage driver to enable technologies such as Native Command Queuing (NCQ) and hot plug.

ALS — ambient light sensor — A feature that helps to control display brightness.

antivirus software — A program designed to identify, quarantine, and/or delete viruses from your computer.

ASF — alert standards format — A standard to define a mechanism for reporting hardware and software alerts to a management console. ASF is designed to be platform- and operating system-independent.

B

battery life span — The length of time (years) during which a portable computer battery is able to be depleted and recharged.

battery operating time — The length of time (minutes or hours) that a portable computer battery powers the computer.

BIOS — basic input/output system — A program (or utility) that serves as an interface between the computer hardware and the operating system. Unless you understand what effect these settings have on the computer, do not change them. Also referred to as system setup.

bit — The smallest unit of data interpreted by your computer.

Bluetooth® wireless technology — A wireless technology standard for short-range (9 m [29 feet]) networking devices that allows for enabled devices to automatically recognize each other.

boot sequence — Specifies the order of the devices from which the computer attempts to boot.

bootable media — A disk that you can use to start your computer. In case your hard drive is damaged or your computer has a virus, ensure that you always have a bootable DVD, CD, or floppy disk available. Your Drivers and Utilities media.

bps — bits per second — The standard unit for measuring data transmission speed.

BTU — British thermal unit — A measurement of heat output.

bus — A communication pathway between the components in your computer.

bus speed — The speed, given in MHz, that indicates how fast a bus can transfer information.

byte — The basic data unit used by your computer. A byte is usually equal to 8 bits.

C — Celsius — A temperature measurement scale where 0° is the freezing point and 100° is the boiling point of water.

cache — A special high-speed storage mechanism which can be either a reserved section of main memory or an independent high-speed storage device. The cache enhances the efficiency of many processor operations.

L1 cache — Primary cache stored inside the processor.

L2 cache — Secondary cache which can either be external to the processor or incorporated into the processor architecture.

carnet — An international customs document that facilitates temporary imports into foreign countries. Also known as a merchandise passport.

CD-R — CD recordable — A recordable version of a CD. Data can be recorded only once onto a CD-R. Once recorded, the data cannot be erased or written over.

CD-RW — CD rewritable — A rewritable version of a CD. Data can be written to a CD-RW disc, and then erased and written over (rewritten).

CD-RW drive — A drive that can read CDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs. You can write to CD-RW discs multiple times,

Page 82 of the Dell Desktop Computer (DCCY) user manual — E
Page 82 · click to enlarge
Page 82

but you can write to CD-R discs only once.

CD-RW/DVD drive — A drive, sometimes referred to as a combo drive, that can read CDs and DVDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs. You can write to CD-RW discs multiple times, but you can write to CD-R discs only once.

clock speed — The speed, given in MHz, that indicates how fast computer components that are connected to the system bus operate.

COA — Certificate of Authenticity — The Windows alpha-numeric code located on a sticker on your computer. Also referred to as the Product Key or Product ID.

Control Panel — A Windows utility that allows you to modify operating system and hardware settings, such as display settings.

controller — A chip that controls the transfer of data between the processor and memory or between the processor and devices.

CRIMM — continuity rambus in-line memory module — A special module that has no memory chips and is used to fill unused RIMM slots.

cursor — The marker on a display or screen that shows where the next keyboard, touch pad, or mouse action will occur. It often is a blinking solid line, an underline character, or a small arrow.

D

DDR SDRAM — double-data-rate SDRAM — A type of SDRAM that doubles the data burst cycle, improving system performance.

DDR2 SDRAM — double-data-rate 2 SDRAM — A type of DDR SDRAM that uses a 4-bit prefetch and other architectural changes to boost memory speed to over 400 MHz.

device — Hardware such as a disk drive, printer, or keyboard that is installed in or connected to your computer.

device driver — See driver.

DIMM — dual in-line memory module — A circuit board with memory chips that connects to a memory module on the system board.

DIN connector — A round, six-pin connector that conforms to DIN (Deutsche Industrie-Norm) standards; it is typically used to connect PS/2 keyboard or mouse cable connectors.

disk striping — A technique for spreading data over multiple disk drives. Disk striping can speed up operations that retrieve data from disk storage. Computers that use disk striping generally allow the user to select the data unit size or stripe width.

DMA — direct memory access — A channel that allows certain types of data transfer between RAM and a device to bypass the processor.

docking device — See APR.

DMTF — Distributed Management Task Force — A consortium of hardware and software companies who develop management standards for distributed desktop, network, enterprise, and Internet environments.

domain — A group of computers, programs, and devices on a network that are administered as a unit with common rules and procedures for use by a specific group of users. A user logs on to the domain to gain access to the resources.

DRAM — dynamic random-access memory — Memory that stores information in integrated circuits containing capacitors.

driver — Software that allows the operating system to control a device such as a printer. Many devices do not work properly if the correct driver is not installed in the computer.

DSL — Digital Subscriber Line — A technology that provides a constant, high-speed Internet connection through an analog telephone line.

dual-core — A technology in which two physical computational units exist inside a single processor package, thereby increasing computing efficiency and multi- tasking ability.

dual display mode — A display setting that allows you to use a second monitor as an extension of your display. Also referred to as extended display mode.

DVD-R — DVD recordable — A recordable version of a DVD. Data can be recorded only once onto a DVD-R. Once recorded, the data cannot be erased or written over.

DVD+RW — DVD rewritable — A rewritable version of a DVD. Data can be written to a DVD+RW disc, and then erased and written over (rewritten). (DVD+RW technology is different from DVD-RW technology.)

DVD+RW drive — drive that can read DVDs and most CD media and write to DVD+RW (rewritable DVDs) discs.

DVI — digital video interface — A standard for digital transmission between a computer and a digital video display.

E

ECC — error checking and correction — A type of memory that includes special circuitry for testing the accuracy of data as it passes in and out of memory.

ECP — extended capabilities port — A parallel connector design that provides improved bidirectional data transmission. Similar to EPP, ECP uses direct memory access to transfer data and often improves performance.

EIDE — enhanced integrated device electronics — An improved version of the IDE interface for hard drives and CD drives.

EMI — electromagnetic interference — Electrical interference caused by electromagnetic radiation.

Page 83 of the Dell Desktop Computer (DCCY) user manual — H
Page 83 · click to enlarge
Page 83

ENERGY STAR® — Environmental Protection Agency requirements that decrease the overall consumption of electricity.

EPP — enhanced parallel port — A parallel connector design that provides bidirectional data transmission.

ESD — electrostatic discharge — A rapid discharge of static electricity. ESD can damage integrated circuits found in computer and communications equipment.

expansion card — A circuit board that installs in an expansion slot on the system board in some computers, expanding the capabilities of the computer. Examples include video, modem, and sound cards.

expansion slot — A connector on the system board (in some computers) where you insert an expansion card, connecting it to the system bus.

ExpressCard — A removable I/O card adhering to the PCMCIA standard. Modems and network adapters are common types of ExpressCards. ExpressCards support both the PCI Express and USB 2.0 standard.

Express Service Code — A numeric code located on a sticker on your Dell™ computer. Use the Express Service Code when contacting Dell for assistance. Express Service Code service may not be available in some countries.

extended display mode — A display setting that allows you to use a second monitor as an extension of your display. Also referred to as dual display mode.

extended PC Card — A PC Card that extends beyond the edge of the PC Card slot when installed.

F

Fahrenheit — A temperature measurement scale where 32° is the freezing point and 212° is the boiling point of water.

FBD — fully-buffered DIMM — A DIMM with DDR2 DRAM chips and an Advanced Memory Buffer (AMB) that speeds communication between the DDR2 SDRAM chips and the system.

FCC — Federal Communications Commission — A U.S. agency responsible for enforcing communications-related regulations that state how much radiation computers and other electronic equipment can emit.

fingerprint reader — A strip sensor that uses your unique fingerprint to authenticate your user identity to help secure your computer.

folder — A term used to describe space on a disk or drive where files are organized and grouped. Files in a folder can be viewed and ordered in various ways, such as alphabetically, by date, and by size.

format — The process that prepares a drive or disk for file storage. When a drive or disk is formatted, the existing information on it is lost.

FSB — front side bus — The data path and physical interface between the processor and RAM.

FTP — file transfer protocol — A standard Internet protocol used to exchange files between computers connected to the Internet.

G

G — gravity — A measurement of weight and force.

GB — gigabyte — A measurement of data storage that equals 1024 MB (1,073,741,824 bytes). When used to refer to hard drive storage, the term is often rounded to 1,000,000,000 bytes.

GHz — gigahertz — A measurement of frequency that equals one thousand million Hz, or one thousand MHz. The speeds for computer processors, buses, and interfaces are often measured in GHz.

graphics mode — A video mode that can be defined as x horizontal pixels by y vertical pixels by z colors. Graphics modes can display an unlimited variety of shapes and fonts.

GUI — graphical user interface — Software that interacts with the user by means of menus, windows, and icons. Most programs that operate on the Windows operating systems are GUIs.

H

hard drive — A drive that reads and writes data on a hard disk. The terms hard drive and hard disk are often used interchangeably.

heat sink — A metal plate on some processors that helps dissipate heat.

hibernate mode — A power management mode that saves everything in memory to a reserved space on the hard drive and then turns off the computer. When you restart the computer, the memory information that was saved to the hard drive is automatically restored.

HTTP — hypertext transfer protocol — A protocol for exchanging files between computers connected to the Internet.

HyperTransport — HyperTransport is an AMD™ technology that can increase overall computer performance by removing bottlenecks, increasing system bandwidth, and reducing system latency.

Hz — hertz — A unit of frequency measurement that equals 1 cycle per second. Computers and electronic devices are often measured in kilohertz (kHz), megahertz (MHz), gigahertz (GHz), or terahertz (THz).

Page 84 of the Dell Desktop Computer (DCCY) user manual — M
Page 84 · click to enlarge
Page 84

IC — integrated circuit — A semiconductor wafer, or chip, on which thousands or millions of tiny electronic components are fabricated for use in computer, audio, and video equipment.

IDE — integrated device electronics — An interface for mass storage devices in which the controller is integrated into the hard drive or CD drive.

IEEE 1394 — Institute of Electrical and Electronics Engineers, Inc. — A high-performance serial bus used to connect IEEE 1394-compatible devices, such as digital cameras and DVD players, to the computer.

infrared sensor — A port that allows you to transfer data between the computer and infrared-compatible devices without using a cable connection.

integrated — Usually refers to components that are physically located on the computer's system board. Also referred to as built-in.

I/O — input/output — An operation or device that enters and extracts data from your computer. Keyboards and printers are I/O devices.

I/O address — An address in RAM that is associated with a specific device (such as a serial connector, parallel connector, or expansion slot) and allows the processor to communicate with that device.

IrDA — Infrared Data Association — The organization that creates international standards for infrared communications.

IRQ — interrupt request — An electronic pathway assigned to a specific device so that the device can communicate with the processor. Each device connection must be assigned an IRQ. Although two devices can share the same IRQ assignment, you cannot operate both devices simultaneously.

ISP — Internet service provider — A company that allows you to access its host server to connect directly to the Internet, send and receive e-mail, and access websites. The ISP typically provides you with a software package, user name, and access phone numbers for a fee.

K

Kb — kilobit — A unit of data that equals 1024 bits. A measurement of the capacity of memory integrated circuits.

KB — kilobyte — A unit of data that equals 1024 bytes but is often referred to as 1000 bytes.

key combination — A command requiring you to press multiple keys at the same time.

kHz — kilohertz — A measurement of frequency that equals 1000 Hz.

LAN — local area network — A computer network covering a small area. A LAN usually is confined to a building or a few nearby buildings. A LAN can be connected to another LAN over any distance through telephone lines and radio waves to form a wide area network (WAN).

LCD — liquid crystal display — The technology used by portable computer and flat-panel displays.

LED — light-emitting diode — An electronic component that emits light to indicate the status of the computer.

local bus — A data bus that provides a fast throughput for devices to the processor.

LPT — line print terminal — The designation for a parallel connection to a printer or other parallel device.

M

Mb — megabit — A measurement of memory chip capacity that equals 1024 Kb.

Mbps — megabits per second — One million bits per second. This measurement is typically used for transmission speeds for networks and modems.

MB — megabyte — A measurement of data storage that equals 1,048,576 bytes. 1 MB equals 1024 KB. When used to refer to hard drive storage, the term is often rounded to 1,000,000 bytes.

MB/sec — megabytes per second — One million bytes per second. This measurement is typically used for data transfer ratings.

media bay — A bay that supports devices such as optical drives, a second battery, or a Dell TravelLite™ module.

memory — A temporary data storage area inside your computer. Because the data in memory is not permanent, it is recommended that you frequently save your files while you are working on them, and always save your files before you shut down the computer. Your computer can contain several different forms of memory, such as RAM, ROM, and video memory. Frequently, the word memory is used as a synonym for RAM.

memory address — A specific location where data is temporarily stored in RAM.

memory mapping — The process by which the computer assigns memory addresses to physical locations at start-up. Devices and software can then identify information that the processor can access.

memory module — A small circuit board containing memory chips, which connects to the system board.

MHz — megahertz — A measure of frequency that equals 1 million cycles per second. The speeds for computer processors, buses, and interfaces are often measured in MHz.

Page 85 of the Dell Desktop Computer (DCCY) user manual — R
Page 85 · click to enlarge
Page 85

Mini PCI — A standard for integrated peripheral devices with an emphasis on communications such as modems and NICs. A Mini PCI card is a small external card that is functionally equivalent to a standard PCI expansion card.

Mini-Card — A small card designed for integrated peripherals, such as communication NICs. The Mini-Card is functionally equivalent to a standard PCI expansion card.

modem — A device that allows your computer to communicate with other computers over analog telephone lines. Three types of modems include: external, PC Card, and internal. You typically use your modem to connect to the Internet and exchange e-mail.

module bay — See media bay.

MP — megapixel — A measure of image resolution used for digital cameras.

ms — millisecond — A measure of time that equals one thousandth of a second. Access times of storage devices are often measured in ms.

N

network adapter — A chip that provides network capabilities. A computer may include a network adapter on its system board, or it may contain a PC Card with an adapter on it. A network adapter is also referred to as a NIC (network interface controller).

NIC — See network adapter.

notification area — The section of the Windows taskbar that contains icons for providing quick access to programs and computer functions, such as the clock, volume control, and print status. Also referred to as system tray.

ns — nanosecond — A measure of time that equals one billionth of a second.

NVRAM — nonvolatile random access memory — A type of memory that stores data when the computer is turned off or loses its external power source. NVRAM is used for maintaining computer configuration information such as date, time, and other system setup options that you can set.

O

optical drive — A drive that uses optical technology to read or write data from CDs, DVDs, or DVD+RWs. Example of optical drives include CD drives, DVD drives, CD-RW drives, and CD-RW/DVD combo drives.

P

parallel connector — An I/O port often used to connect a parallel printer to your computer. Also referred to as an LPT port.

partition — A physical storage area on a hard drive that is assigned to one or more logical storage areas known as logical drives. Each partition can contain multiple logical drives.

PC Card — A removable I/O card adhering to the PCMCIA standard. Modems and network adapters are common types of PC Cards.

PCI — peripheral component interconnect — PCI is a local bus that supports 32-and 64-bit data paths, providing a high-speed data path between the processor and devices such as video, drives, and networks.

PCI Express — A modification to the PCI interface that boosts the data transfer rate between the processor and the devices attached to it. PCI Express can transfer data at speeds from 250 MB/sec to 4 GB/sec. If the PCI Express chip set and the device are capable of different speeds, they will operate at the slower speed.

PCMCIA — Personal Computer Memory Card International Association — The organization that establishes standards for PC Cards.

PIO — programmed input/output — A method of transferring data between two devices through the processor as part of the data path.

pixel — A single point on a display screen. Pixels are arranged in rows and columns to create an image. A video resolution, such as 800 x 600, is expressed as the number of pixels across by the number of pixels up and down.

Plug-and-Play — The ability of the computer to automatically configure devices. Plug and Play provides automatic installation, configuration, and compatibility with existing hardware if the BIOS, operating system, and all devices are Plug and Play compliant.

POST — power-on self-test — Diagnostics programs, loaded automatically by the BIOS, that perform basic tests on the major computer components, such as memory, hard drives, and video. If no problems are detected during POST, the computer continues the start-up.

processor — A computer chip that interprets and executes program instructions. Sometimes the processor is referred to as the CPU (central processing unit).

PS/2 — personal system/2 — A type of connector for attaching a PS/2-compatible keyboard, mouse, or keypad.

PXE — pre-boot execution environment — A WfM (Wired for Management) standard that allows networked computers that do not have an operating system to be configured and started remotely.

R

RAID — redundant array of independent disks — A method of providing data redundancy. Some common implementations of RAID include RAID 0, RAID 1, RAID 5, RAID 10, and RAID 50.

Page 86 of the Dell Desktop Computer (DCCY) user manual — S
Page 86 · click to enlarge
Page 86

RAM — random-access memory — The primary temporary storage area for program instructions and data. Any information stored in RAM is lost when you shut down your computer.

readme file — A text file included with a software package or hardware product. Typically, readme files provide installation information and describe new product enhancements or corrections that have not yet been documented.

read-only — Data and/or files you can view but cannot edit or delete. A file can have read-only status if:

¡ It resides on a physically write-protected floppy disk, CD, or DVD.

¡ It is located on a network in a directory and the system administrator has assigned rights only to specific individuals.

refresh rate — The frequency, measured in Hz, at which your screen's horizontal lines are recharged (sometimes also referred to as its vertical frequency). The higher the refresh rate, the less video flicker can be seen by the human eye.

resolution — The sharpness and clarity of an image produced by a printer or displayed on a monitor. The higher the resolution, the sharper the image.

RFI — radio frequency interference — Interference that is generated at typical radio frequencies, in the range of 10 kHz to 100,000 MHz. Radio frequencies are at the lower end of the electromagnetic frequency spectrum and are more likely to have interference than the higher frequency radiations, such as infrared and light.

ROM — read-only memory — Memory that stores data and programs that cannot be deleted or written to by the computer. ROM, unlike RAM, retains its contents after you shut down your computer. Some programs essential to the operation of your computer reside in ROM.

RPM — revolutions per minute — The number of rotations that occur per minute. Hard drive speed is often measured in rpm.

RTC — real time clock — Battery-powered clock on the system board that keeps the date and time after you shut down the computer.

RTCRST — real-time clock reset — A jumper on the system board of some computers that can often be used for troubleshooting problems.

S

SAS — serial attached SCSI — A faster, serial version of the SCSI interface (as opposed to the original SCSI parallel architecture).

SATA — serial ATA — A faster, serial version of the ATA (IDE) interface.

ScanDisk — A Microsoft utility that checks files, folders, and the hard disk's surface for errors. ScanDisk often runs when you restart the computer after it has stopped responding.

SCSI — small computer system interface — A high-speed interface used to connect devices to a computer, such as hard drives, CD drives, printers, and scanners. The SCSI can connect many devices using a single controller. Each device is accessed by an individual identification number on the SCSI controller bus.

SDRAM — synchronous dynamic random-access memory — A type of DRAM that is synchronized with the optimal clock speed of the processor.

serial connector — An I/O port often used to connect devices such as a handheld digital device or digital camera to your computer.

Service Tag — A bar code label on your computer that identifies your computer when you access Dell Support at support.dell.com or when you call Dell for customer service or technical support.

setup program — A program that is used to install and configure hardware and software. The setup.exe or install.exe program comes with most Windows software packages. Setup program differs from system setup.

shortcut — An icon that provides quick access to frequently used programs, files, folders, and drives. When you place a shortcut on your Windows desktop and double-click the icon, you can open its corresponding folder or file without having to find it first. Shortcut icons do not change the location of files. If you delete a shortcut, the original file is not affected. Also, you can rename a shortcut icon.

SIM — Subscriber Identity Module — A SIM card contains a microchip that encrypts voice and data transmissions. SIM cards can be used in phones or portable computers.

smart card — A card that is embedded with a processor and a memory chip. Smart cards can be used to authenticate a user on computers equipped for smart cards.

S/PDIF — Sony/Philips Digital Interface — An audio transfer file format that allows the transfer of audio from one file to another without converting it to and from an analog format, which could degrade the quality of the file.

standby mode — A power management mode that shuts down all unnecessary computer operations to save energy.

Strike Zone™ — Reinforced area of the platform base that protects the hard drive by acting as a dampening device when a computer experiences resonating shock or is dropped (whether the computer is on or off).

surge protectors — Prevent voltage spikes, such as those that may occur during an electrical storm, from entering the computer through the electrical outlet. Surge protectors do not protect against lightning strikes or against brownouts, which occur when the voltage drops more than 20 percent below the normal AC-line voltage level.

Network connections cannot be protected by surge protectors. Always disconnect the network cable from the network connector during electrical storms.

SVGA — super-video graphics array — A video standard for video cards and controllers. Typical SVGA resolutions are 800 x 600 and 1024 x 768.

The number of colors and resolution that a program displays depends on the capabilities of the monitor, the video controller and its drivers, and the amount of video memory installed in the computer.

S-video TV-out — A connector used to attach a TV or digital audio device to the computer.

SXGA — super-extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1280 x 1024.

Page 87 of the Dell Desktop Computer (DCCY) user manual — W
Page 87 · click to enlarge
Page 87

SXGA+ — super-extended graphics array plus — A video standard for video cards and controllers that supports resolutions up to 1400 x 1050.

system board — The main circuit board in your computer. Also known as the motherboard.

system setup — A utility that serves as an interface between the computer hardware and the operating system. System setup allows you to configure user- selectable options in the BIOS, such as date and time or system password. Unless you understand what effect the settings have on the computer, do not change the settings for this program.

T

TAPI — telephony application programming interface — Enables Windows programs to operate with a wide variety of telephony devices, including voice, data, fax, and video.

text editor — A program used to create and edit files that contain only text; for example, Windows Notepad uses a text editor. Text editors do not usually provide word wrap or formatting functionality (the option to underline, change fonts, and so on).

TPM — trusted platform module — A hardware-based security feature that when combined with security software enhances network and computer security by enabling features such as file and e-mail protection.

travel module — A plastic device designed to fit inside the module bay of a portable computer to reduce the weight of the computer.

U

UMA — unified memory allocation — System memory dynamically allocated to video.

UPS — uninterruptible power supply — A backup power source used when the electrical power fails or drops to an unacceptable voltage level. A UPS keeps a computer running for a limited amount of time when there is no electrical power. UPS systems typically provide surge suppression and may also provide voltage regulation. Small UPS systems provide battery power for a few minutes to enable you to shut down your computer.

USB — universal serial bus — A hardware interface for a low-speed device such as a USB-compatible keyboard, mouse, joystick, scanner, set of speakers, printer, broadband devices (DSL and cable modems), imaging devices, or storage devices. Devices are plugged directly in to a 4-pin socket on your computer or in to a multi-port hub that plugs in to your computer. USB devices can be connected and disconnected while the computer is turned on, and they can also be daisy-chained together.

UTP — unshielded twisted pair — Describes a type of cable used in most telephone networks and some computer networks. Pairs of unshielded wires are twisted to protect against electromagnetic interference, rather than relying on a metal sheath around each pair of wires to protect against interference.

UXGA — ultra extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1600 x 1200.

video controller — The circuitry on a video card or on the system board (in computers with an integrated video controller) that provides the video capabilities—in combination with the monitor—for your computer.

video memory — Memory that consists of memory chips dedicated to video functions. Video memory is usually faster than system memory. The amount of video memory installed primarily influences the number of colors that a program can display.

video mode — A mode that describes how text and graphics are displayed on a monitor. Graphics-based software, such as Windows operating systems, displays in video modes that can be defined as x horizontal pixels by y vertical pixels by z colors. Character-based software, such as text editors, displays in video modes that can be defined as x columns by y rows of characters.

video resolution — See resolution.

virus — A program that is designed to inconvenience you or to destroy data stored on your computer. A virus program moves from one computer to another through an infected disk, software downloaded from the Internet, or e-mail attachments. When an infected program starts, its embedded virus also starts.

A common type of virus is a boot virus, which is stored in the boot sectors of a floppy disk. If the floppy disk is left in the drive when the computer is shut down and then turned on, the computer is infected when it reads the boot sectors of the floppy disk expecting to find the operating system. If the computer is infected, the boot virus may replicate itself onto all the floppy disks that are read or written in that computer until the virus is eradicated.

V — volt — The measurement of electric potential or electromotive force. One V appears across a resistance of 1 ohm when a current of 1 ampere flows through that resistance.

W

W — watt — The measurement of electrical power. One W is 1 ampere of current flowing at 1 volt.

WHr — watt-hour — A unit of measure commonly used to indicate the approximate capacity of a battery. For example, a 66-WHr battery can supply 66 W of power for 1 hour or 33 W for 2 hours.

wallpaper — The background pattern or picture on the Windows desktop. Change your wallpaper through the Windows Control Panel. You can also scan in your favorite picture and make it wallpaper.

WLAN — wireless local area network. A series of interconnected computers that communicate with each other over the air waves using access points or wireless routers to provide Internet access.

Page 88 of the Dell Desktop Computer (DCCY) user manual — Z
Page 88 · click to enlarge
Page 88

write-protected — Files or media that cannot be changed. Use write-protection when you want to protect data from being changed or destroyed. To write- protect a 3.5-inch floppy disk, slide its write-protect tab to the open position.

WWAN — wireless wide area network. A wireless high-speed data network using cellular technology and covering a much larger geographic area than WLAN.

WXGA — wide-aspect extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1280 x 800.

XGA — extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1024 x 768.

Z

ZIF — zero insertion force — A type of socket or connector that allows a computer chip to be installed or removed with no stress applied to either the chip or its socket.

Zip — A popular data compression format. Files that have been compressed with the Zip format are called Zip files and usually have a filename extension of .zip. A special kind of zipped file is a self-extracting file, which has a filename extension of .exe. You can unzip a self-extracting file by double-clicking it.

Zip drive — A high-capacity floppy drive developed by Iomega Corporation that uses 3.5-inch removable disks called Zip disks. Zip disks are slightly larger than regular floppy disks, about twice as thick, and hold up to 100 MB of data.

Page 89 of the Dell Desktop Computer (DCCY) user manual — Mini Tower, Desktop, and Small Form Factor Matched Pairs
Page 89 · click to enlarge
Page 89

Memory

Dell™ Optiplex™ 740 Systems User's Guide

Addressing Memory With 4-GB or Greater Configurations (32-bit Operating Systems Only)

Your computer supports non-ECC DDR2 memory only. For more information on the type of memory supported by your computer, see the "Memory" section of the specifications for your computer:

l Mini Tower Computer (Model #DCSM) Specifications

l Desktop Computer (Model # DCNE) Specifications

l Small Form Factor Computer (Model # DCCY) Specifications

DDR2 Memory Overview

Dual-channel DDR2 memory modules should be installed in pairs of matched memory size. If the DDR2 memory modules are not installed with the same amount of memory in each channel, the computer will continue to operate, but with a slight reduction in performance. See the label in the upper-right corner of the module to determine the module's capacity.

Dell Desktop Computer (DCCY) — DDR2 Memory Overview diagram (page 89)
Fig. 71 · DDR2 Memory Overview

The recommended memory configurations are:

l A pair of matched memory modules installed in connectors DIMM1 and DIMM2

l A memory module installed in connector DIMM1

l A pair of matched memory modules installed in connectors DIMM1 and DIMM2 and another matched pair installed in connectors DIMM3 and DIMM4

Be sure to install a single memory module in DIMM1, the connector closest to the edge of the system board, before you install modules in the other connectors.

Mini Tower, Desktop, and Small Form Factor Matched Pairs

Dell Desktop Computer (DCCY) — Mini Tower, Desktop, and Small Form Factor Matched Pairs diagram (page 89)
Fig. 72 · Mini Tower, Desktop, and Small Form Factor Matched P…

A matched pair of memory modules in connectors DIMM1 and DIMM2 (white securing clips)

B matched pair of memory modules in connectors DIMM3 and DIMM4 (black securing clips).

Show 5 more labels / short text on this page
DDR2 Memory Overview · Removing Memory · Installing Memory · or · or
Page 90 of the Dell Desktop Computer (DCCY) user manual — Removing Memory
Page 90 · click to enlarge
Page 90

Addressing Memory With 4-GB or Greater Configurations (32-bit Operating Systems Only)

This computer supports a maximum of 8 GB of memory. Current 32-bit operating systems, such as Microsoft® Windows® XP, can use a maximum of 4 GB of address space; however, the amount of memory available to the operating system is less than that installed. Certain components within the computer require address space in the 4-GB range. Any address space reserved for these components cannot be used by computer memory.

The following components require memory address space:

l Integrated PCI devices, such as network connectors and SCSI controllers

l PCI Express cards (if applicable)

At start-up, the BIOS identifies the components that require address space. The BIOS dynamically calculates the amount of reserved address space required. The BIOS then subtracts the reserved address space from 4 GB to determine the amount of usable space.

l If the total installed computer memory is less than the usable address space, all installed computer memory is available for use only by the operating

system.

l If the total installed computer memory is equal to or greater than the usable address space, a portion of installed memory is not available for use by

the operating system.

Removing Memory

NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. If possible, do not pair an original memory module with a new memory module. Otherwise, your computer may not start properly. You should install your original memory modules in pairs either in connectors DIMM1 and DIMM2 or connectors DIMM3 and DIMM4.

1. Follow the procedures in Before You Begin . 2. If you are using:

l a desktop computer: remove the optical drive (see Removing an Optical Drive).

l a small form factor computer: first remove the optical drive (see Removing an Optical Drive)then remove the floppy drive or Media Card Reader.

(see Removing a Floppy Drive or Media Card Reader). 3. Carefully press out the securing clip at each end of the memory module connector.

Dell Desktop Computer (DCCY) — Removing Memory diagram (page 90)
Fig. 73 · Removing Memory

1 securing clip (2) 2 memory module

4. Remove the memory module. If you are replacing a memory module, see Installing Memory . 5. If you are using:

l a desktop computer: replace the optical drive (see Installing an Optical Drive).

l a small form factor computer: first replace the floppy drive or media card reader (see Installing a Floppy Drive or Media Card Reader) and then

replace the optical drive (see Installing an Optical Drive). 6. Replace the computer cover (see Replacing the Computer Cover).

Show 4 more labels / short text on this page
l System ROM · l APIC(s) · l PCI cards · l Graphics card(s)
Page 91 of the Dell Desktop Computer (DCCY) user manual — Installing Memory
Page 91 · click to enlarge
Page 91

Installing Memory

1. Follow the procedures in Before You Begin . 2. If you are using:

l a desktop computer: remove the optical drive (see Removing an Optical Drive).

l a small form factor computer: first remove the optical drive (see Removing an Optical Drive) and then remove the floppy drive or media card

reader (see Removing a Floppy Drive or Media Card Reader). 3. Press out the securing clip at each end of the memory module connector.

Dell Desktop Computer (DCCY) — Installing Memory diagram (page 91)
Fig. 74 · Installing Memory

1 memory connector closest to processor 2 connector 3 securing clips (2)

4. Align the notch on the bottom of the module with the crossbar in the connector.
Dell Desktop Computer (DCCY) — Installing Memory diagram (page 91)
Fig. 75 · Installing Memory

1 cutouts (2) 2 memory module 3 notch

5. Insert the module into the connector until the module snaps into position.

If you insert the module correctly, the securing clips snap into the cutouts at each end of the module.

4 crossbar

Page 92 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 92 · click to enlarge
Page 92
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 92)
Fig. 76 · Removing a PCI Card From the Riser-Card Cage
6. If you are using:

l a desktop computer: replace the optical drive (see Installing an Optical Drive).

l a small form factor computer: first replace the floppy drive or media card reader (see Installing a Floppy Drive or Media Card Reader) and then

replace the optical drive (see Installing an Optical Drive). 7. Replace the computer cover (see Replacing the Computer Cover). 8. The computer detects that the new memory does not match the existing configuration information and generates the following message:

The amount of system memory has changed. Strike the F1 key to continue, F2 to run the setup utility

9. Press to enter system setup and check the value for System Memory .

The computer should have changed the value of System Memory to reflect the newly installed memory. Verify the new total. If it is correct, skip to step 11.

10. If the memory total is incorrect, turn off and disconnect your computer and devices from their electrical outlets. Open the computer cover and check the installed memory modules to ensure that they are seated properly in their sockets. Then repeat steps 7, 8, and 9. 11. When the System Memory total is correct, press to exit system setup. 12. Run the Dell Diagnostics (see Dell Diagnostics) to verify that the memory modules are operating properly.

Page 93 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Card
Page 93 · click to enlarge
Page 93

PCI, PCI Express Cards, and PS/2 Serial Port Adapters

PCI, PCI Express Cards, and PS/2 Serial Port Adapters

Your Dell™ computer supports a PS/2 serial adapter and provides the following connectors for PCI and PCI Express cards.

l Two PCI card slots

l One PCI Express x16 card slot

l One PCI Express x1 card slot

PCI Cards

Installing a PCI Card

1. Follow the procedures in Before You Begin .
2. Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position.
Dell Desktop Computer (DCCY) — Installing a PCI Card diagram (page 93)
Fig. 77 · Installing a PCI Card

1 card retention latch 2 alignment guide 3 card

4 card-edge connector 5 card connector 6 release tab

3. If you are installing a new card, remove the filler bracket to create a card-slot opening. Then continue with step 5 . 4. If you are replacing a card that is already installed in the computer, remove the card (see Removing a PCI Card ). If necessary, disconnect any cables connected to the card. Then continue with step 6 .
Page 94 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card
Page 94 · click to enlarge
Page 94
5. Prepare the new card for installation.
6. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 94)
Fig. 78 · Removing a PCI Card From the Riser-Card Cage

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

7. Secure the card(s) by closing the card retention latch and snapping it into place.
8. Connect any cables that should be attached to the card. 9. Replace the computer cover (see Replacing the Computer Cover ).
10. If you installed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors). 11. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 12. Install any drivers required for the card as described in the card documentation.

Removing a PCI Card

1. Follow the procedures in Before You Begin 2. Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position.
Page 95 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 95 · click to enlarge
Page 95

1 card retention latch 2 alignment guide 3 card

4 card-edge connector 5 card connector 6 release tab

3. If necessary, disconnect any cables connected to the card. 4. Grasp the card by its top corners, and ease it out of its connector. 5. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
6. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

7. Secure the card(s) by closing the card retention latch and snapping it into place. 8. Replace the computer cover (see Replacing the Computer Cover ). 9. Uninstall the card's driver. See the documentation that came with the card for instructions. 10. If you removed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer. 11. If you removed an network-adapter card connector:

Page 96 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Express x1 Card
Page 96 · click to enlarge
Page 96

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

PCI Express Cards

Your computer supports one PCI Express x16 card and one PCI Express x1 card. See System Board Components for the location of the PCI Express card slots.

Dell Desktop Computer (DCCY) — PCI Express Cards diagram (page 96)
Fig. 79 · PCI Express Cards

1 PCI Express x1 card 2 PCI Express x16 card 3 PCI Express x16 DVI card

4 PCI Express x1 card slot 5 PCI Express x16 card slot 6 PCI Express x16 DVI card slot

If you are replacing a card, uninstall the driver for the existing card. See the documentation that came with the card for instructions.

Installing a PCI Express x1 Card

1. Follow the procedures in Before You Begin .

1 card retention latch 2 alignment guide 3 card

4 card-edge connector 5 card connector 6 release tab

2. Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position. 3. If you are installing a new card, remove the filler bracket to create a card-slot opening. Then continue with step 5 . 4. If you are replacing a card that is already installed in the computer, remove the card (see Removing a PCI Express x1 Card ).

If necessary, disconnect any cables connected to the card. Then continue with step 6.

5. Prepare the new card for installation.

See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your computer.

Page 97 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 97 · click to enlarge
Page 97
6. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 97)
Fig. 80 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x1 card 2 PCI Express x1 card connector

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

7. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

8. Close the card retention latch and gently press until it clicks into place.
9. Connect any cables that should be attached to the card.

See the documentation for the card for information about the card's cable connections.

10. Replace the computer cover (see Replacing the Computer Cover ). 11. If you installed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup. b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer. Back-Panel Connectors. 12. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup. b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 13. Install any drivers required for the card as described in the card documentation.

Page 98 of the Dell Desktop Computer (DCCY) user manual — Installing PCI Express x16 Cards and DVI-Cards
Page 98 · click to enlarge
Page 98

Removing a PCI Express x1 Card

1. Follow the procedures in Before You Begin . 2. Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position.

1 card retention latch 2 alignment guide 3 card

4 card-edge connector 5 card connector 6 release tab

3. If necessary, disconnect any cables connected to the card. 4. Grasp the card by its top corners, and ease it out of its connector. 5. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
6. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

7. Secure the card(s) by closing the card retention latch and snapping it into place. 8. Replace the computer cover (see Replacing the Computer Cover ).

Installing PCI Express x16 Cards and DVI-Cards

1. Follow the procedures in Before You Begin . 2. If you are replacing a PCI Express x16 card, remove the installed card (see Removing PCI Express x16 Cards and DVI-Cards ).
3. Prepare the card for installation.
4. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.
Page 99 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 99 · click to enlarge
Page 99
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 99)
Fig. 81 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x16 card 2 PCI Express x16 card connector

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 99)
Fig. 82 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x16 card 2 DVI-card connector 3 PCI Express x16 card connector

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

5. Connect any cables that should be attached to the card.
6. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

7. Secure the card(s) by closing the card retention latch and snapping it into place. 8. Replace the computer cover (see Replacing the Computer Cover ). 9. If you installed a sound card:
Page 100 of the Dell Desktop Computer (DCCY) user manual — Removing PCI Express x16 Cards and DVI-Cards
Page 100 · click to enlarge
Page 100

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).

10. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 11. Install any drivers required for the card as described in the card documentation.

Removing PCI Express x16 Cards and DVI-Cards

1. Follow the procedures in Before You Begin . 2. Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position. 3. If necessary, disconnect any cables connected to the card. 4. Press the lever with your thumb until you release the securing tab.

If you are removing a PCI Express x16 card, go to step 5.

If you are removing a DVI-card, go to step 6

5. While pressing the lever, pull the card up and out of the card connector.
Dell Desktop Computer (DCCY) — Removing PCI Express x16 Cards and DVI-Cards diagram (page 100)
Fig. 83 · Removing PCI Express x16 Cards and DVI-Cards

1 PCI Express x16 card 2 lever 3 securing slot

4 securing tab 5 PCI Express x16 card connector

6. While pressing the lever, pull the removal pull tab up and remove the card out of the card connector.
Dell Desktop Computer (DCCY) — Removing PCI Express x16 Cards and DVI-Cards diagram (page 100)
Fig. 84 · Removing PCI Express x16 Cards and DVI-Cards
Page 101 of the Dell Desktop Computer (DCCY) user manual — Installing a PS/2 Serial Port Adapter
Page 101 · click to enlarge
Page 101

1 PCI Express x16 DVI-card 2 removal pull tab 3 DVI-card connector

4 lever 5 securing slot 6 securing tab

7 PCI Express x16 card connector

7. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
8. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

9. Secure any remaining card(s) by closing the card retention latch and snapping it into place.
10. Replace the computer cover (see Replacing the Computer Cover ). 11. Uninstall the card's driver. See the documentation that came with the card for instructions. 12. If you removed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.

13. If you removed a network-adapter card connector:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

PS/2 Serial Port Adapters

Installing a PS/2 Serial Port Adapter

1. Follow the procedures in Before You Begin . 2. Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position.
Page 102 of the Dell Desktop Computer (DCCY) user manual — Removing a PS/2 Serial Port Adapter
Page 102 · click to enlarge
Page 102
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 102)
Fig. 85 · Removing a PCI Card From the Riser-Card Cage

1 card retention latch 2 alignment guide

3. Remove the filler bracket (if applicable).
4. Align the PS/2 serial-port adapter bracket in the retention slot and press down firmly. Ensure that the adapter is fully seated in the slot.

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

Before you close the card retention mechanism, ensure that:

l The tops of all adapters and filler brackets are flush with the alignment bar.

l The notch in the top of the adapter or filler bracket fits around the alignment guide.

l Close the card retention latch and gently press until it snaps into place.

6. Connect the adapter cable to the serial port adapter connector (PS2/SER2) on the system board (see System Board Components for connector locations).
7. Replace the computer cover (see Replacing the Computer Cover ).

Removing a PS/2 Serial Port Adapter

Page 103 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 103 · click to enlarge
Page 103
1. Follow the procedures in Before You Begin . 2. Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position.

1 card retention latch 2 alignment guide

3. Disconnect the PS/2 serial adapter cable from the system board (see System Board Components ). 4. If necessary, disconnect any external cables connected to the adapter. 5. Grasp the PS/2 serial-port adapter bracket by its top corners, and ease it out of its retention slot. 6. If you are removing the adapter permanently, install a filler bracket in the empty card-slot opening.
7. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

8. Secure the card(s) by closing the card retention latch and snapping it into place. 9. Replace the computer cover (see Replacing the Computer Cover ).
Page 104 of the Dell Desktop Computer (DCCY) user manual — Removing the Processor
Page 104 · click to enlarge
Page 104

Dell™ Optiplex™ 740 Systems User's Guide

Processor

Removing the Processor

1. Follow the procedures in Before You Begin . 2. Loosen the captive screw on each side of the heat sink assembly.
3. Rotate the heat sink assembly upward, and remove it from the computer.

Lay the heat sink assembly down on its top, with the thermal grease facing upward.

Dell Desktop Computer (DCCY) — Removing the Processor diagram (page 104)
Fig. 86 · Removing the Processor

1 heat sink assembly 2 captive screw housings (2)

4. Pull the release lever straight up until the processor is released.

Processor

Page 105 of the Dell Desktop Computer (DCCY) user manual — Installing the Processor
Page 105 · click to enlarge
Page 105
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 105)
Fig. 87 · Removing a PCI Card From the Riser-Card Cage

1 processor 2 release lever 3 socket

5. Remove the processor from the socket.

Leave the release lever extended in the release position so that the socket is ready for the new processor and go to Installing the Processor.

Installing the Processor

1. Follow the procedures in Before You Begin .
2. Unpack the new processor, being careful not to bend any of the processor pins.
3. If the release lever on the socket is not fully extended, move it to that position. 4. Align the pin-1 corners of the processor and socket.
Page 106 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 106 · click to enlarge
Page 106
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 106)
Fig. 88 · Removing a PCI Card From the Riser-Card Cage

1 socket and processor pin-1 indicator 2 processor 3 release lever

5. Set the processor lightly in the socket and ensure that the processor is positioned correctly. 6. While lightly pressing down on the processor, rotate the release lever back toward the system board until it snaps into place, securing the processor. 7. Clean the thermal grease from the bottom of the heat sink.
8. Apply the new thermal grease to the top of the processor.
9. Install the heat sink assembly:

a. Place the heat sink assembly back onto the heat-sink assembly bracket. b. Rotate the heat sink assembly down towards the computer base and ensure that the two captive screws are properly aligned with the holes in the system board. c. Tighten the two captive screws.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 106)
Fig. 89 · Removing a PCI Card From the Riser-Card Cage

1 heat sink assembly 2 heat-sink assembly bracket 3 captive screw housing (2)

4 processor socket

Page 107 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 107 · click to enlarge
Page 107
10. Replace the computer cover (see Replacing the Computer Cover ).
Page 108 of the Dell Desktop Computer (DCCY) user manual — Drive Interface Connectors
Page 108 · click to enlarge
Page 108

Dell™ Optiplex™ 740 Systems User's Guide

Drives

Your computer supports:

l Two SATA (Serial ATA) hard drives

l One optional floppy drive or Media Card Reader

l Two optical drives

Dell Desktop Computer (DCCY) — Dell™ Optiplex™ 740 Systems User's Guide diagram (page 108)
Fig. 90 · Dell™ Optiplex™ 740 Systems User's Guide

1 optical drive 2 floppy drive or media card reader 3 hard drive

General Installation Guidelines

Connect SATA hard drives to the connectors labeled "SATA0" or "SATA1." Connect SATA CD or DVD drives to the connectors labeled "SATA2" or "SATA3" on the system board (see System Board Components for information about mini tower system board connectors).

Connecting Drive Cables

When you install a drive, you connect two cables—a DC power cable and a data cable—to the back of the drive and to the system board.

Drive Interface Connectors

1 interface cable connector 2 interface connector

Drives · Serial ATA Connector

Page 109 of the Dell Desktop Computer (DCCY) user manual — Removing a Hard Drive
Page 109 · click to enlarge
Page 109

Interface connectors are keyed for correct insertion.

Power Cable Connectors

Serial ATA Power Connector

Dell Desktop Computer (DCCY) — Power Cable Connectors diagram (page 109)
Fig. 91 · Power Cable Connectors

1 power cable 2 power input connector

Connecting and Disconnecting Drive Cables

When connecting and disconnecting a SATA data cable, hold the cable by the black connector at each end.

Hard Drive

Removing a Hard Drive

1. If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. 2. Follow the procedures in Before You Begin . 3. Disconnect the power and hard-drive cables from the drive.
Page 110 of the Dell Desktop Computer (DCCY) user manual — Installing a Hard Drive
Page 110 · click to enlarge
Page 110
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 110)
Fig. 92 · Removing a PCI Card From the Riser-Card Cage

1 hard-drive cable 2 hard-drive cable on system board 3 power cable

4. Press in on the blue release tabs on each side of the drive and slide the drive up and out of the computer.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 110)
Fig. 93 · Removing a PCI Card From the Riser-Card Cage

1 hard drive 2 release tabs (2)

Installing a Hard Drive

1. Unpack the replacement hard drive, and prepare it for installation. 2. Follow the procedures in Before You Begin . 3. If your replacement hard drive does not have the plastic hard-drive bracket attached:

a. Remove the bracket from the existing drive by gently spreading the plastic hard-bracket and removing the hard drive. b. Install the replacement drive into the bracket by inserting the drive into the bracket so that the bracket alignment tabs snaps into the mounting holes on the new drive.

Page 111 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 111 · click to enlarge
Page 111
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 111)
Fig. 94 · Removing a PCI Card From the Riser-Card Cage

1 hard drive 2 hard-drive bracket

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 111)
Fig. 95 · Removing a PCI Card From the Riser-Card Cage

1 hard drive 2 hard drive mounting holes 3 hard-drive bracket

4 bracket alignment tabs

4. Carefully slide the hard drive into the drive bay until it clicks into place.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 111)
Fig. 96 · Removing a PCI Card From the Riser-Card Cage

5. Connect the power and hard-drive cables to the drive. 6. Check all connectors to be certain that they are properly cabled and firmly seated. 7. Replace the computer cover (see Replacing the Computer Cover). 8. If the drive you just installed is the primary drive, insert a bootable medium into your boot drive. See the documentation that came with the drive for instructions on installing any software required for drive operation. 9. Enter system setup and update the appropriate Primary Drive option (0 or 1) (see Entering System Setup). 10. Exit system setup, and reboot the computer.

Page 112 of the Dell Desktop Computer (DCCY) user manual — Adding a Second Hard Drive
Page 112 · click to enlarge
Page 112
11. Partition and logically format your drive before you proceed to the next step.

See the documentation for your operating system for instructions.

12. Test the hard drive by running the Dell Diagnostics (see Dell Diagnostics ). 13. If the drive you just installed is the primary drive, install your operating system on the hard drive.

Adding a Second Hard Drive

1. Check the documentation for the drive to verify that it is configured for your computer. 2. Follow the procedures in Before You Begin. 3. Remove the plastic hard-drive bracket from the inside of the hard-drive bay by squeezing the release tabs and gently pulling the bracket up and out of the bay. 4. Install the new drive into the bracket by inserting the drive into the bracket so that the bracket alignment tabs snaps into the mounting holes on the new drive.

Dell Desktop Computer (DCCY) — Adding a Second Hard Drive diagram (page 112)
Fig. 97 · Adding a Second Hard Drive

1 hard drive 2 hard drive mounting holes 3 hard-drive bracket

4 bracket alignment tabs

5. If necessary, disconnect the power and SATA cables from the hard drive that is currently installed. 6. Carefully slide the new hard drive into the unused bay until it clicks into place. 7. Connect the power and SATA cables to the drives.
Page 113 of the Dell Desktop Computer (DCCY) user manual — Drive-Panel Inserts
Page 113 · click to enlarge
Page 113
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 113)
Fig. 98 · Removing a PCI Card From the Riser-Card Cage
8. Locate and connect a SATA cable to the SATA1 connector on the system board (see System Board Components for mini tower computers).
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 113)
Fig. 99 · Removing a PCI Card From the Riser-Card Cage

1 hard-drive data cable

2 hard-drivedata cable on system board

3 hard-drive power cable

9. Replace the computer cover (see Replacing the Computer Cover ).

Drive-Panel Inserts

If you are installing a new floppy drive, media card reader, or optical drive instead of replacing a drive, remove the drive-panel inserts.

1. Follow the procedures in Before You Begin . 2. Remove the drive panel by sliding the drive release latch in the direction indicated on the latch to open the panel. Then remove it from the hinges.
Page 114 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 114 · click to enlarge
Page 114
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 114)
Fig. 100 · Removing a PCI Card From the Riser-Card Cage

1 drive panel 2 release tab 3 drive-panel insert

3. Select the drive-panel insert in front of the drive bay that you want to use. 4. Gently press the release tab of the insert to remove it from the drive panel.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 114)
Fig. 101 · Removing a PCI Card From the Riser-Card Cage

1 optical-drive panel insert

2 floppy-drive/media card reader panel insert

3 holder for shoulder screws

5. Reattach the drive panel to the front of the computer.

The drive panel only fits one way.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 114)
Fig. 102 · Removing a PCI Card From the Riser-Card Cage
Page 115 of the Dell Desktop Computer (DCCY) user manual — Installing the Floppy Drive
Page 115 · click to enlarge
Page 115

Floppy Drive

Removing the Floppy Drive

1. Follow the procedures in Before You Begin. 2. Remove the drive panel by sliding the drive release latch in the direction indicated on the latch to open the panel. Then remove it from the hinges. 3. Disconnect the power and floppy-drive cables from the back of the floppy drive. 4. Slide the drive release latch in the direction indicated on the latch until the floppy drive is released; while holding the latch open, slide the drive out of the computer.

Dell Desktop Computer (DCCY) — Removing the Floppy Drive diagram (page 115)
Fig. 103 · Removing the Floppy Drive

1 floppy drive 2 drive release latch

Installing the Floppy Drive

1. If you are replacing a floppy drive, remove the shoulder screws from the existing drive and attach the screws to the replacement drive. 2. If you are installing a new floppy drive, remove the drive-panel insert (see Drive-Panel Inserts ) for your new drive, remove the shoulder screws from the inside of the drive-panel insert and attach the screws to the new drive.
Dell Desktop Computer (DCCY) — Installing the Floppy Drive diagram (page 115)
Fig. 104 · Installing the Floppy Drive
3. Align the shoulder screws on the floppy drive with the shoulder screw slots, and gently slide the drive into the bay until it clicks into place.
Page 116 of the Dell Desktop Computer (DCCY) user manual — Removing the Media Card Reader
Page 116 · click to enlarge
Page 116
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 116)
Fig. 105 · Removing a PCI Card From the Riser-Card Cage

1 floppy drive 2 shoulder screws (4) 3 shoulder screw slots (2)

4. Attach the power and floppy-drive data cables to the floppy drive. 5. Connect the floppdrive data cable to the DSKT connector on the system board (see System Board Components for the connector location). 6. Install the drive panel to the front of the computer. The drive panel only fits one way (see Drive-Panel Inserts ).
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 116)
Fig. 106 · Removing a PCI Card From the Riser-Card Cage

1 power cable 2 floppy-drive data cable

3 floppy-drive connector on system board (DSKT)

7. Replace the computer cover (see Replacing the Computer Cover ). 8. Enter system setup and use the Diskette Drive option to enable your new floppy drive (see Entering System Setup ). 9. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics ).

Media Card Reader

Removing the Media Card Reader

Page 117 of the Dell Desktop Computer (DCCY) user manual — Installing the Media Card Reader
Page 117 · click to enlarge
Page 117

1. Follow the procedures in Before You Begin. 2. Remove the drive panel by sliding the drive release latch in the direction indicated on the latch to open the panel. Then remove it from the hinges. 3. Disconnect the media card reader cable from the back of the media card reader. 4. Slide the drive release latch in the direction indicated on the latch until the media card reader is released; while holding the latch open, slide the device out of the computer.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 117)
Fig. 107 · Removing a PCI Card From the Riser-Card Cage

1 media card reader 2 media card reader cable 3 drive release latch

Installing the Media Card Reader

1. If you are replacing a media card reader, remove the shoulder screws from the existing device and attach the screws to the replacement device. 2. If you are installing a new media card reader, remove the drive-panel insert (see Drive-Panel Inserts) for your new device, remove the shoulder screws from the inside of the drive-panel insert and attach the screws to the new device. 3. Align the shoulder screws on the media card reader with the shoulder screw slots, and gently slide the device into the bay until it clicks into place. 4. Attach the media card reader cable to the media card reader. 5. Connect the media card reader cable to the USB1 connector on the system board (see System Board Components for the connector location).

Dell Desktop Computer (DCCY) — Installing the Media Card Reader diagram (page 117)
Fig. 108 · Installing the Media Card Reader

1 media card reader 2 shoulder screws (4) 3 shoulder screw slots (2)

4 media card reader cable

Page 118 of the Dell Desktop Computer (DCCY) user manual — Installing an Optical Drive
Page 118 · click to enlarge
Page 118
6. Install the drive panel to the front of the computer. The drive panel only fits one way (see Drive-Panel Inserts ). 7. Replace the computer cover (see Replacing the Computer Cover ). 8. Enter system setup and use the Diskette Drive option to enable your new media card reader (see Entering System Setup ). 9. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics ).

Optical Drive

Removing an Optical Drive

1. Follow the procedures in Before You Begin. 2. Remove the drive panel by sliding the drive release latch in the direction indicated on the latch to open the panel. Then remove it from the hinges. 3. Disconnect the power and optical drive cables from the back of the drive. 4. Slide the drive release latch in the direction indicated on the latch until the optical drive is released; while holding the latch open, slide the drive out of the computer.

Dell Desktop Computer (DCCY) — Removing an Optical Drive diagram (page 118)
Fig. 109 · Removing an Optical Drive

1 optical drive 2 drive release latch

Installing an Optical Drive

1. Follow the procedures in Before You Begin . 2. If you are replacing a optical drive, remove the shoulder screws from the existing drive and attach the screws to the replacement drive. 3. If you are installing a new optical drive, remove the drive-panel insert for your new drive (see DrivePanel Inserts ), remove the shoulder screws from the inside of the drive-panel insert, and attach the screws to the new drive.
Dell Desktop Computer (DCCY) — Installing an Optical Drive diagram (page 118)
Fig. 110 · Installing an Optical Drive
Page 119 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 119 · click to enlarge
Page 119
4. Align the shoulder screws on the optical drive with the shoulder screw slots, and slide the drive into the bay until it clicks into place.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 119)
Fig. 111 · Removing a PCI Card From the Riser-Card Cage

1 optical drive 2 shoulder screws (3) 3 shoulder screw slots (2)

5. Connect the power and optical drive cables to the drive. 6. Connect the drive cable to SATA2 or SATA3 on the system board (see System Board Components for mini tower computers).
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 119)
Fig. 112 · Removing a PCI Card From the Riser-Card Cage

1 power cable 2 optical drive cable 3 optical drive connector (SATA)

See the documentation that accompanied the drive and controller card to verify that the configuration is correct for your computer. Change any settings necessary for correct configuration.

7. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 8. Install the drive panel to the front of the computer. The drive panel only fits one way (see Drive-Panel Inserts). 9. Replace the computer cover (see Replacing the Computer Cover). 10. Update your configuration information in system setup (see System Setup) by setting the appropriate Drive option (0 or 1) under Drives. 11. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics).

Page 120 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 120 · click to enlarge
Page 120
Page 120 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 121 of the Dell Desktop Computer (DCCY) user manual — Notes, Notices, and Cautions
Page 121 · click to enlarge
Page 121

Dell™ OptiPlex™ 740 User's Guide

Mini Tower Computer

About Your Computer Finding Information Mini Tower Computer Mini Tower Computer (Model # DCSM) Specifications Advanced Features Cleaning Your Computer Reinstalling Drivers and the Operating System Solving Problems Microsoft® Windows® XP and Windows Vista® Features Troubleshooting Tools and Utilities Getting Help Warranty FCC Regulatory Model (U.S. Only) Glossary

Removing and Replacing Parts Before You Begin Removing the Computer Cover Chassis Intrusion Switch I/O Panel Drives PCI, PCI Express Cards, and PS/2 Serial Port Adapters Power Supply Processor Battery Replacing the System Board Memory Replacing the Computer Cover

ModelsDCSM, DCNE, and DCCY

Notes, Notices, and Cautions

Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, OptiPlex, Inspiron, Dimension, Latitude, Dell Precision, DellNet, TravelLite, Dell OpenManage, PowerVault, Axim, PowerEdge, PowerConnect, and PowerApp are trademarks of Dell Inc.; AMD, AMD Athlon, AMD Phenom, and combinations thereof, and Cool 'n' Quiet are trademarks of Advanced Micro Devices, Inc; Microsoft and Windows are registered trademarks of Microsoft Corporation; IBM is a registered trademark of International Business Machines Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

March 2008 RP699 Rev. A03

Page 122 of the Dell Desktop Computer (DCCY) user manual — Replacing the I/O Panel
Page 122 · click to enlarge
Page 122

Dell™ Optiplex™ 740 Systems User's Guide

I/O Panel

Removing the I/O Panel

1. Follow the procedures in Before You Begin .
2. Remove the screw that secures the I/O panel. Press on the release button and slide the card away from the front of the computer. 3. Carefully remove the panel from the computer. 4. Disconnect all of the cables from the I/O panel.
Dell Desktop Computer (DCCY) — Dell™ Optiplex™ 740 Systems User's Guide diagram (page 122)
Fig. 113 · Dell™ Optiplex™ 740 Systems User's Guide

1 I/O panel release button 2 securing screw 3 I/O panel

4 I/O cable connector 5 pull-loop

Replacing the I/O Panel

To replace the I/O panel, follow the removal procedure in the reverse order.

I/O Panel

Page 123 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 123 · click to enlarge
Page 123
Page 123 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 124 of the Dell Desktop Computer (DCCY) user manual — Dell™ Optiplex™ 740 Systems User's Guide
Page 124 · click to enlarge
Page 124

Dell™ Optiplex™ 740 Systems User's Guide

Power Supply

Replacing the Power Supply

1. Follow the procedures in Before You Begin . 2. Disconnect the DC power cables from the system board and the drives.
3. Remove the four screws that attach the power supply to the back of the computer chassis. 4. Press the release button located on the floor of the computer chassis.
Dell Desktop Computer (DCCY) — Dell™ Optiplex™ 740 Systems User's Guide diagram (page 124)
Fig. 114 · Dell™ Optiplex™ 740 Systems User's Guide

1 release button 2 power supply 3 screws (4)

4 AC power connector

5. Slide the power supply toward the front of the computer by approximately 1 inch. 6. Lift the power supply up and out of the computer. 7. Slide the replacement power supply into place. 8. Replace the screws that secure the power supply to the back of the computer chassis.

Power Supply

Page 125 of the Dell Desktop Computer (DCCY) user manual — DC Power Connector P1
Page 125 · click to enlarge
Page 125
9. Reconnect the DC power cables to the system board and drives. 10. Replace the computer cover (see Replacing the Computer Cover ). 11. Connect the AC power cable to the AC power connector.

DC Power Connectors

Dell Desktop Computer (DCCY) — DC Power Connectors diagram (page 125)
Fig. 115 · DC Power Connectors

DC Power Connector P1

Dell Desktop Computer (DCCY) — DC Power Connector P1 diagram (page 125)
Fig. 116 · DC Power Connector P1
Dell Desktop Computer (DCCY) — DC Power Connector P1 diagram (page 125)
Fig. 117 · DC Power Connector P1
Page 126 of the Dell Desktop Computer (DCCY) user manual — DC Power Connector P7
Page 126 · click to enlarge
Page 126
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 126)
Fig. 118 · Removing a PCI Card From the Riser-Card Cage

DC Power Connector P2

Dell Desktop Computer (DCCY) — DC Power Connector P2 diagram (page 126)
Fig. 119 · DC Power Connector P2

DC Power Connectors P3, P5, P8, and P9

Dell Desktop Computer (DCCY) — DC Power Connectors P3, P5, P8, and P9 diagram (page 126)
Fig. 120 · DC Power Connectors P3, P5, P8, and P9

DC Power Connector P7

Dell Desktop Computer (DCCY) — DC Power Connector P7 diagram (page 126)
Fig. 121 · DC Power Connector P7
Page 127 of the Dell Desktop Computer (DCCY) user manual — Removing the Computer Cover
Page 127 · click to enlarge
Page 127

Dell™ Optiplex™ 740 Systems User's Guide

Removing the Computer Cover

Removing the Computer Cover

1. Follow the procedures in Before You Begin . 2. Lay the computer on its side as shown in the illustration. 3. Locate the cover release latch shown in the illustration. Then, slide the release latch back as you lift the cover. 4. Grip the sides of the computer cover and pivot the cover up using the hinge tabs as leverage points. 5. Remove the cover from the hinge tabs and set it aside on a soft nonabrasive surface.
Dell Desktop Computer (DCCY) — Removing the Computer Cover diagram (page 127)
Fig. 122 · Removing the Computer Cover

1 security cable slot 2 cover release latch 3 padlock ring

Page 128 of the Dell Desktop Computer (DCCY) user manual — Mini Tower Computer (Model #DCSM) Specifications
Page 128 · click to enlarge
Page 128

Mini Tower Computer (Model #DCSM) Specifications

Mini Tower Computer (Model #DCSM) Specifications

Microprocessor type AMD Phenom™ processors

AMD Athlon™ 64 X2 Dual-Core processor

Internal cache AMD Phenom Quad-Core2-MB L2 dedicated cache and 2-MB shared L3 cache
AMD Phenom Triple-Core1.5-MB L2 dedicated cache and 2-MB shared L3 cache
AMD Athlon 64 X22-MB L2 dedicated cache

AMD Athlon 64 X2:1-MB L2 dedicated cache

AMD Athlon1-MB L2 dedicated cache
AMD Athlon512-KB L2 dedicated cache

Type 533-, 667-, or 800-MHz DDR2 SDRAM

Memory modules supported 256 MB, 512 MB, 1 GB, or 2 GB non-ECC

Minimum memory dual-channel512 MB single-channel: 256 MB

Maximum memory 8 GB

Chipset nVidia GeForce 6150LE/Nforce 430

RAID support RAID 0 and RAID 1

Data bus width 64 bits

Address bus width 40 bits

BIOS chip (NVRAM) 8 Mb or 4 Mb

NIC support for Atmel 1-Mb and 2-Mb EEPROM

Show 7 more labels / short text on this page
Microprocessor · AMD Athlon 64 · Memory · Memory connectors 4 · Computer Information · DMA channels eight · Interrupt levels 24
Page 129 of the Dell Desktop Computer (DCCY) user manual — PCI:
Page 129 · click to enlarge
Page 129

Capable of 10/100/1000 communication

Type nVidia integrated video (DirectX 9.0c Shader Model 3.0 Graphics Processing Unit) or PCI Express x16 graphics card or DVI graphics card

Type Sigma Tel 9200 CODEC (2.1 Channel Audio)

Stereo conversion 24-bit analog-to-digital; 24-bit digital-to-analog

Drives two SATA controllers supporting two devices each, including two 3.5-inch hard drives

Bus type PCI 2.3 PCI Express 1.0A SATA 1.0A and 2.0 USB 2.0

Bus speed PCI: 133 MB/s PCI Express x16: 40 GB/s bidirectional speed PCI Express x1: 2.5 Gbps SATA: 1.5 Gbps and 3.0 Gbps USB: 480-Mbps high speed, 12-Mbps full speed, 1.2- Mbps low speed

Cardsfull-height cards supported

PCI:

connector size 124 pins

PCI Express:

connectors one x1 and one x16

power 10 W (x1) and 75 W (x16) maximum

connector size 36 pins (x1) and 164 pins (x16)

connector data width (maximum) one PCI Express lane (x1) and 16 PCI Express lanes (x16)

Externally accessible two 3.5-inch drive bays, including support for up to two 3.5-inch hard drives two 5.25-inch drive bays

Internally accessible two bays for 1-inch-high hard drives

External connectors:

Serial 9-pin connector; 16550C-compatible

Parallel 25-hole connector (bidirectional)

Video 15-hole VGA connector

Optional DVI 36-pin connector

Network adapter RJ45 connector

Optional PS/2 with secondary serial port adapter

Show 11 more labels / short text on this page
Video · Audio · Controllers · Expansion Bus · connectors two · connector data width · 32 bits · (maximum) · Drives · Connectors · two 6-pin mini-DINs
Page 130 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 130 · click to enlarge
Page 130

USB two front-panel and five back-panel USB 2.0– compliant connectors

Audio two connectors for line-in and line-out; two front- panel connectors for headphones and microphone

System board connectors:

SATA four 7-pin connectors

Floppy drive 34-pin connector

Serial 24-pin connector for optional second serial port card

PCI 2.3 two 124-pin connectors

Internal USB 10-pin connector

Intrusion switch 3-pin connector

Memory modules four 240-pin connector

Power 12V 4-pin connector

Front panel 40-pin connector

in Microsoft® Windows® XP and Windows Vista®, brings up the Windows Security window. If in MS- DOS® mode, restarts (reboots) the computer.

or starts embedded system setup (during start-up only)

or displays a boot device menu that allows the user to enter a device for a single boot (during start-up only) as well as options to run hard-drive and system diagnostics

starts the RAID setup menu if RAID is turned on in the system setup program

disables computer password at start-up (after correct password is entered)

Power control front of chassis - push button

Power light (within the power button) green light — Blinking green indicates sleep mode; solid green indicates power-on state.

amber light — Blinking amber indicates a problem with an installed device; solid amber indicates an internal power problem (see Power Problems).

Hard-drive access light front panel - green

Link light (on front panel) front panel - solid green light indicates network connection

Link integrity light (on integrated network adapter) rear panel - green light for 10-Mb operation; orange light for 100-Mb operation; yellow light for a 1000-Mb (1-Gb) operation

Activity light (on integrated network adapter) rear panel - yellow blinking light

Diagnostic lights front panel - four lights on the front panel. See Diagnostic Lights.

Standby power light AUX_PWR on the system board

DC power supply:

Heat dissipation 1040.7 BTU/hr maximum

Voltage manual selection power supplies—90 to 135 V at 50/60 Hz; 180 to 265 V at 50/60 Hz

Backup battery 3-V CR2032 lithium coin cell

Show 10 more labels / short text on this page
Fan 5-pin connector · PCIe-x1 36-pin connector · PCIe-x16 164-pin connector · Speaker 5-pin connector · Power 24-pin connector · Battery 2-pin socket · Key Combinations · Controls and Lights · Power · Wattage 305 W
Page 131 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 131 · click to enlarge
Page 131
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 131)
Fig. 123 · Removing a PCI Card From the Riser-Card Cage

Operating 0.25 G at 3 to 200 Hz at 0.5 octave/min

Storage 0.5 G at 3 to 200 Hz at 1 octave/min

Operating bottom half-sine pulse with a change in velocity of 50.8 cm/sec (20 inches/sec)

Storage 27-G faired square wave with a velocity change of 508 cm/sec (200 inches/sec)

Operating –15.2 to 3048 m (–50 to 10,000 ft)

Storage –15.2 to 10,668 m (–50 to 35,000 ft)

Airborne contaminant level G2 or lower as defined by ISA-S71.04-1985

Page 132 of the Dell Desktop Computer (DCCY) user manual — Removing a Speaker
Page 132 · click to enlarge
Page 132

Dell™ Optiplex™ 740 Systems User's Guide

Speaker

Installing a Speaker

1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ). 3. Insert the speaker into the chassis of the computer.
Dell Desktop Computer (DCCY) — Dell™ Optiplex™ 740 Systems User's Guide diagram (page 132)
Fig. 124 · Dell™ Optiplex™ 740 Systems User's Guide
4. Connect the cables to the system board. 5. Replace the computer cover. 6. Turn on power to the computer.

Removing a Speaker

1. Follow the procedures in Before You Begin . 2. Remove the cover of your computer (see Removing the Computer Cover ). 3. Disconnect the cables from the system board.

Speaker

Page 133 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 133 · click to enlarge
Page 133
4. Remove the speaker from the chassis of the computer.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 133)
Fig. 125 · Removing a PCI Card From the Riser-Card Cage
5. Replace the computer cover. 6. Turn on power to the computer.
Page 134 of the Dell Desktop Computer (DCCY) user manual — Running the Files and Settings Transfer Wizard With the Operating System Media
Page 134 · click to enlarge
Page 134

Microsoft ® Windows ® XP and Windows Vista ® Features

Transferring Information to a New Computer

User Accounts and Fast User Switching

Setting Up a Home and Office Network

Transferring Information to a New Computer

You can use your operating system "wizards" to help you transfer files and other data from one computer to another—for example, from an old computer to a new computer. For instructions, see the following section that corresponds to the operating system that your computer is running.

Microsoft Windows Vista ®

1. Click the Windows Vista Start button and then click Transfer files and settings ® Start Windows Easy Transfer. 2. In the User Account Control dialog box, click Continue . 3. Click Start a new transfer or Continue a transfer in progress .

Follow the instructions provided on the screen by the Windows Easy Transfer wizard.

Microsoft ® Windows ® XP

The Microsoft Windows XP operating system provides the Files and Settings Transfer Wizard to move data from a source computer to a new computer. You can transfer data, such as:

You can transfer the data to the new computer over a network or serial connection, or you can store it on removable media, such as a writable CD, for transfer to the new computer.

NOTE: You can transfer information from an old computer to a new computer by directly connecting a serial cable to the input/output (I/O) ports of the two computers. To transfer data over a serial connection, you must access the Network Connections utility from the Control Panel and perform additional configuration steps, such as setting up an advanced connection and designating the host computer and the guest computer. For instructions on setting up a direct cable connection between two computers, see Microsoft Knowledge Base Article #305621, titled How to Set Up a Direct Cable Connection Between Two Computers in Windows XP. This information may not be available in certain countries.

For transferring information to a new computer, you must run the Files and Settings Transfer Wizard. You can use the optional Operating System media for this process or you can create a wizard disk with the Files and Settings Transfer Wizard.

Running the Files and Settings Transfer Wizard With the Operating System Media

To prepare a new computer for the file transfer:

1. Open the Files and Settings Transfer Wizard: click Start® All Programs® Accessories® System Tools® Files and Settings Transfer Wizard. 2. When the Files and Settings Transfer Wizard welcome screen appears, click Next. 3. On the Which computer is this? screen, click New Computer® Next. 4. On the Do you have a Windows XP CD? screen, click I will use the wizard from the Windows XP CD® Next. 5. When the Now go to your old computer screen appears, go to your old or source computer. Do not click Next at this time.

To copy data from the old computer:

Show 4 more labels / short text on this page
l E-mail messages · l Toolbar settings · l Window sizes · l Internet bookmarks
Page 135 of the Dell Desktop Computer (DCCY) user manual — Running the Files and Settings Transfer Wizard Without the Operating System Media
Page 135 · click to enlarge
Page 135

1. On the old computer, insert the Windows XP Operating System media. 2. On the Welcome to Microsoft Windows XP screen, click Perform additional tasks. 3. Under What do you want to do?, click Transfer files and settings® Next. 4. On the Which computer is this? screen, click Old Computer® Next. 5. On the Select a transfer method screen, click the transfer method you prefer. 6. On the What do you want to transfer? screen, select the items you want to transfer and click Next.

After the information has been copied, the Completing the Collection Phase screen appears.

7. Click Finish .

To transfer data to the new computer:

1. On the Now go to your old computer screen on the new computer, click Next . 2. On the Where are the files and settings? screen, select the method you chose for transferring your settings and files and click Next .

The wizard reads the collected files and settings and applies them to your new computer.

When all of the settings and files have been applied, the Finished screen appears.

3. Click Finished and restart the new computer.

Running the Files and Settings Transfer Wizard Without the Operating System Media

To run the Files and Settings Transfer Wizard without the Operating System media, you must create a wizard disk that will allow you to create a backup image file to removable media.

To create a wizard disk, use your new computer with Windows XP and perform the following steps:

1. Open the Files and Settings Transfer Wizard: click Start® All Programs® Accessories® System Tools® Files and Settings Transfer Wizard. 2. When the Files and Settings Transfer Wizard welcome screen appears, click Next. 3. On the Which computer is this? screen, click New Computer® Next. 4. On the Do you have a Windows XP CD? screen, click I want to create a Wizard Disk in the following drive® Next. 5. Insert the removable media, such as a writable CD, and click OK. 6. When the disk creation completes and the Now go to your old computer message appears, do not click Next. 7. Go to the old computer.

To copy data from the old computer:

1. On the old computer, insert the wizard disk. 2. Click Start® Run. 3. In the Open field on the Run window, browse to the path for fastwiz (on the appropriate removable media) and click OK. 4. On the Files and Settings Transfer Wizard welcome screen, click Next. 5. On the Which computer is this? screen, click Old Computer® Next. 6. On the Select a transfer method screen, click the transfer method you prefer. 7. On the What do you want to transfer? screen, select the items you want to transfer and click Next.

After the information has been copied, the Completing the Collection Phase screen appears.

Page 136 of the Dell Desktop Computer (DCCY) user manual — Windows XP
Page 136 · click to enlarge
Page 136
8. Click Finish .

To transfer data to the new computer:

1. On the Now go to your old computer screen on the new computer, click Next . 2. On the Where are the files and settings? screen, select the method you chose for transferring your settings and files and click Next . Follow the instructions on the screen.

The wizard reads the collected files and settings and applies them to your new computer.

When all of the settings and files have been applied, the Finished screen appears.

3. Click Finished and restart the new computer.

My Old Computer To My New Dell™ Computer Using the Microsoft® Windows® XP Operating System?).

User Accounts and Fast User Switching

Adding User Accounts

After the operating system is installed, the administrator or a user with administrator rights can create additional user accounts.

Windows Vista

1. Click the Windows Vista Start button and click Control Panel . 2. Click Add or remove user accounts .

If the User Account Control dialog box appears, click Continue or type an administrator password and click Submit.

3. In the Manage Accounts window, click Create a new account . 4. Type the name you want to use for the new account and click the account type you want. 5. Click Create Account .

The new account name appears in the User Accounts window.

Windows XP

1. Click the Start button and click Control Panel . 2. In the Control Panel window, click User Accounts . 3. Under Pick a task , click Create a new account . 4. Under Name the new account , type the name of the new user and click Next . 5. Under Pick an account type , click one of the following options:

l Computer administrator — You can change all computer settings.

l Limited — You can change only your own personal settings, such as your password. You cannot install programs or use the Internet.

6. Click Create Account .
Page 137 of the Dell Desktop Computer (DCCY) user manual — Setting Up a Home and Office Network
Page 137 · click to enlarge
Page 137

Fast User Switching

Fast User Switching allows multiple users to access one computer without requiring the previous user to log off.

Windows Vista

1. Click the Windows Vista Start button and then click Transfer files and settings ® Start Windows Easy Transfer.

The current user's name and picture appear on the Start menu.

2. Click the right-arrow icon in the lower-right corner of the Start menu. 3. Click Switch User . 4. Click the name of the user account you want to switch to. 5. Enter your password, if applicable. 6. Click the Go arrow. 7. Click Start .

The user's name and picture now appear in the Start menu.

Windows XP

1. Click the Start button and click Log Off . 2. In the Log Off Windows window, click Switch User .

When you use Fast User Switching, programs that previous users were using remain running in the background, which might decrease your computer's response time. Also, multimedia programs, such as games and DVD software, might not work with Fast User Switching. For more information, see the Windows Help and Support Center.

Setting Up a Home and Office Network

Connecting to a Network Adapter

1. Connect the network cable to the network adapter connector on the back of your computer.

Insert the cable until it clicks into place, and then gently pull it to ensure that it is secure.

2. Connect the other end of the network cable to a network device.
Dell Desktop Computer (DCCY) — Setting Up a Home and Office Network diagram (page 137)
Fig. 126 · Setting Up a Home and Office Network
Page 138 of the Dell Desktop Computer (DCCY) user manual — Windows XP
Page 138 · click to enlarge
Page 138

1 network adapter connector 2 network device 3 network cable

4 network adapter connector on computer

Network Setup Wizard

Windows Vista

1. Click the Windows Vista Start button and then click Connect To ® Set up a connection or network . 2. Select an option under Choose a connection option . 3. Click Next , and then follow the instructions in the wizard.

Windows XP

The Microsoft® Windows® XP operating system provides a Network Setup Wizard to guide you through the process of sharing files, printers, or an Internet connection between computers in a home or small office.

1. Click the Start button, point to All Programs ® Accessories ® Communications , and then click Network Setup Wizard . 2. On the Network Setup Wizard welcome screen, click Next . 3. Click Checklist for creating a network .
4. Complete the checklist and required preparations. 5. Return to the Network Setup Wizard and follow the instructions on the screen.
Page 139 of the Dell Desktop Computer (DCCY) user manual — Dell™ Optiplex™ 740 Systems User's Guide
Page 139 · click to enlarge
Page 139

Replacing the Computer Cover

Dell™ Optiplex™ 740 Systems User's Guide

1. Ensure that all cables are connected, and fold cables out of the way.

Gently pull the power cables toward you so that they do not get caught underneath the drives.

2. Ensure that no tools or extra parts are left inside the computer. 3. To replace the cover:

a. Align the bottom of the cover with the hinge tabs located along the bottom edge of the computer. b. Using the hinge tabs as leverage, rotate the cover downward until it snaps into place.

Dell Desktop Computer (DCCY) — Dell™ Optiplex™ 740 Systems User's Guide diagram (page 139)
Fig. 127 · Dell™ Optiplex™ 740 Systems User's Guide

c. Ensure that the cover is seated correctly before moving the computer.

4. Connect your computer and devices to electrical outlets, and turn them on.

After you remove and replace the cover, the chassis intrusion detector, if installed and enabled, causes the following message to appear on the screen at the next computer start-up:

ALERT! Cover was previously removed.

5. Reset the chassis intrusion detector in System Setup by changing Chassis Intrusion to On or OnSilent (see System Setup ).
Page 140 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Card
Page 140 · click to enlarge
Page 140

PCI, PCI Express Cards, and PS/2 Serial Port Adapters

PCI, PCI Express Cards, and PS/2 Serial Port Adapters

Your Dell™ computer supports a PS/2 serial port adapter and provides the following connectors for PCI and PCI Express cards:

l One low-profile PCI card slot

l One low-profile PCI Express x16 card slot

PCI Cards

Installing a PCI Card

1. Follow the procedures in Before You Begin .
2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open.
Dell Desktop Computer (DCCY) — Installing a PCI Card diagram (page 140)
Fig. 128 · Installing a PCI Card

1 release tab 2 card retention latch 3 card

4 card-edge connector 5 card connector

3. If you are installing a new card, remove the filler bracket to create a card-slot opening. Then continue with step 5 . 4. If you are replacing a card that is already installed in the computer, remove the card. If necessary, disconnect any cables connected to the card. Then continue with step 6 . 5. Prepare the card for installation.
Page 141 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card
Page 141 · click to enlarge
Page 141
6. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 141)
Fig. 129 · Removing a PCI Card From the Riser-Card Cage

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

7. Before closing the card retention latch, ensure that:

l The tops of all cards and filler brackets are flush with the alignment guide

l The notch in the top of the card or filler bracket fits around the alignment guide

8. Secure the card(s) by closing the card retention latch and snapping it into place.
9. Connect any cables that should be attached to the card. 10. Replace the computer cover (see Replacing the Computer Cover ).
11. If you installed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).

12. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 13. Install any drivers required for the card as described in the card documentation.

Removing a PCI Card

1. Follow the procedures in Before You Begin .
Page 142 of the Dell Desktop Computer (DCCY) user manual — PCI Express and DVI Cards
Page 142 · click to enlarge
Page 142
2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open. 3. If necessary, disconnect any cables connected to the card. 4. Grasp the card by its top corners, and ease it out of its connector.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 142)
Fig. 130 · Removing a PCI Card From the Riser-Card Cage

1 release tab 2 card retention latch 3 card

4 card-edge connector 5 card connector

5. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
6. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

7. Secure any remaining card(s) by closing the card retention latch and snapping it into place. 8. Replace the computer cover (see Replacing the Computer Cover ). 9. Uninstall the card's driver. See the documentation that came with the card for instructions. 10. If you removed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.

11. If you removed a network-adapter card connector:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

PCI Express and DVI Cards

Your computer supports one low-profile PCI Express x16 card.

If you are replacing a PCI Express card with a different type of PCI Express card, remove the current driver for the card from the operating system. See the documentation that came with the card for information.

Page 143 of the Dell Desktop Computer (DCCY) user manual — Installing a PCI Express x16 Card or DVI Card
Page 143 · click to enlarge
Page 143

Installing a PCI Express x16 Card or DVI Card

1. Follow the procedures in Before You Begin .

2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open. 3. If you are installing a new PCI Express x16 card or DVI card, remove the filler bracket to create a card- slot opening. Then continue with step 5. 4. If you are replacing a PCI Express x16 card or DVI card, remove the card (see Removing a PCI Express x16 Card or DVI Card). If necessary, disconnect any cables connected to the card. Then continue with step 6. 5. Prepare the card for installation.

6. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.

1 PCI Express x16 card 2 PCI Express x16 card connector

1 PCI Express x16 DVI-card 2 DVI card connector 3 PCI Express x16 card connector

Page 144 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Express x16 Card or DVI Card
Page 144 · click to enlarge
Page 144
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 144)
Fig. 131 · Removing a PCI Card From the Riser-Card Cage

1 fully seated card 2 not fully seated card 3 bracket within slot

4 bracket caught outside of slot

7. Connect any cables that should be attached to the card. 8. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

9. Secure the card(s) by closing the card retention latch and snapping it into place. 10. Replace the computer cover (see Replacing the Computer Cover ).
11. If you installed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the line-in connector on the back panel of the computer (see Back-Panel Connectors).

12. If you installed a network adapter card and want to turn off the integrated network adapter:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to Off (see System Setup). b. Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on the back panel of the computer. 13. Install any drivers required for the card as described in the card documentation.

Removing a PCI Express x16 Card or DVI Card

1. Follow the procedures in Before You Begin . 2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open. 3. If necessary, disconnect any cables connected to the card. 4. Press the lever with your thumb until you release the securing tab.

If you are removing a PCI Express x16 card, go to step 5.

If you are removing a DVI card, go to step 6

5. While pressing the lever, pull the card up and out of the card connector.
Page 145 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 145 · click to enlarge
Page 145
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 145)
Fig. 132 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x16 card 2 lever 3 securing slot (not all cards)

4 securing tab 5 PCI Express x16 card connector

6. While pressing the lever, pull the removal pull tab up and remove the card out of the card connector.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 145)
Fig. 133 · Removing a PCI Card From the Riser-Card Cage

1 PCI Express x16 DVI-card 2 removal pull tab 3 DVI card connector

4 lever 5 securing slot 6 securing tab

7 PCI Express x16 card connector

7. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
8. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

9. Secure any remaining card(s) by closing the card retention latch and snapping it into place.
10. Replace the computer cover (see Replacing the Computer Cover ). 11. Uninstall the card's driver. See the documentation that came with the card for instructions. 12. If you removed a sound card:

a. Enter system setup, select Integrated Audio from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect external audio devices to the audio connectors on the back panel of the computer.

Page 146 of the Dell Desktop Computer (DCCY) user manual — Installing a PS/2 Serial Port Adapter
Page 146 · click to enlarge
Page 146
13. If you removed a network-adapter card connector:

a. Enter system setup, select Integrated NIC from the Onboard Devices group, and change the setting to On (see System Setup). b. Connect the network cable to the integrated network connector on the back panel of the computer.

PS/2 Serial Port Adapters

Installing a PS/2 Serial Port Adapter

1. Follow the procedures in Before You Begin . 2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open. 3. Remove the filler bracket (if applicable).
4. Align the PS/2 serial-port adapter bracket in the retention slot and press down firmly. Ensure that the adapter is fully seated in the slot. 5. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

6. Secure the card(s) by closing the card retention latch and snapping it into place.
Dell Desktop Computer (DCCY) — Installing a PS/2 Serial Port Adapter diagram (page 146)
Fig. 134 · Installing a PS/2 Serial Port Adapter

1 release tab 2 adapter retention latch 3 serial port adapter bracket

4 serial port adapter connector

5 serial port adapter system board connector (PS2/SER2)

7. Connect the adapter cable to the PS/2 serial port adapter connector (PS2/SER2) on the system board (see System Board Components ).
8. Replace the computer cover (see Replacing the Computer Cover ).
Page 147 of the Dell Desktop Computer (DCCY) user manual — Removing a PS/2 Serial Port Adapter
Page 147 · click to enlarge
Page 147

Removing a PS/2 Serial Port Adapter

1. Follow the procedures in Before You Begin . 2. Gently lift the release tab on the card retention latch from the inside and pivot the latch open. 3. Disconnect the PS/2 serial port cable from the system board (see System Board Components ). 4. Grasp the PS/2 serial port adapter bracket by its top corners, and ease it out of its connector. 5. If you are removing the adapter permanently, install a filler bracket in the empty card-slot opening.
6. Before you close the card retention mechanism, ensure that:

l The tops of all cards and filler brackets are flush with the alignment bar.

l The notch in the top of the card or filler bracket fits around the alignment guide.

7. Secure any remaining card(s) by closing the card retention latch and snapping it into place. 8. Replace the computer cover (see Replacing the Computer Cover ).
Page 148 of the Dell Desktop Computer (DCCY) user manual — Removing the Processor
Page 148 · click to enlarge
Page 148

Dell™ Optiplex™ 740 Systems User's Guide

Processor

Removing the Processor

1. Follow the procedures in Before You Begin . 2. Remove the hard drive (see Removing a Hard Drive ). 3. If installed, remove the floppy drive cable from the cable routing clips on the heat sink assembly. 4. Loosen the captive screw on each side of the heat sink assembly.
5. Rotate the heat sink assembly upward, and remove the assembly from the computer. Lay the heat sink down on its top, with the thermal grease facing upward.
Dell Desktop Computer (DCCY) — Removing the Processor diagram (page 148)
Fig. 135 · Removing the Processor

1 heat sink assembly 2 captive screws in housing (2)

6. Pull the release lever straight up until the processor is released.

Processor

Page 149 of the Dell Desktop Computer (DCCY) user manual — Installing the Processor
Page 149 · click to enlarge
Page 149
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 149)
Fig. 136 · Removing a PCI Card From the Riser-Card Cage

1 processor 2 release lever 3 socket

7. Remove the processor from the socket.

Leave the release lever extended in the release position so that the socket is ready for the new processor, and go to Installing the Processor.

Installing the Processor

1. Follow the procedures in Before You Begin .
2. Unpack the new processor, being careful not to bend any of the processor pins.
3. If the release lever on the socket is not fully extended, move it to that position. 4. Align the pin-1 corners of the processor and socket.
Page 150 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 150 · click to enlarge
Page 150
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 150)
Fig. 137 · Removing a PCI Card From the Riser-Card Cage

1 socket and processor pin-1 indicator 2 processor 3 release lever

5. Set the processor lightly in the socket and ensure that the processor is positioned correctly. 6. While lightly pressing down on the processor, rotate the release lever back toward the system board until it snaps into place, securing the processor. 7. Clean the thermal grease from the bottom of the heat sink.
8. Apply the new thermal grease to the top of the processor. 9. Install the heat sink assembly:

a. Place the heat sink assembly back onto the heat-sink assembly bracket. b. Rotate the heat sink assembly down towards the computer base and ensure that the two captive screws are properly aligned with the holes in the system board c. Tighten the two captive screws.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 150)
Fig. 138 · Removing a PCI Card From the Riser-Card Cage

1 heat sink assembly 2 heat-sink assembly bracket 3 captive screw in housing (2)

10. Route the floppy drive cable through the cable routing clips on the heat sink assembly. 11. Replace the hard drive (see Installing a Hard Drive ). 12. Replace the computer cover (see Replacing the Computer Cover ).

4 processor socket

Page 151 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 151 · click to enlarge
Page 151
Page 151 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 152 of the Dell Desktop Computer (DCCY) user manual — Removing the Computer Cover
Page 152 · click to enlarge
Page 152

Dell™ Optiplex™ 740 Systems User's Guide

Removing the Computer Cover

Removing the Computer Cover

1. Follow the procedures in Before You Begin. 2. If you have installed a padlock through the padlock ring on the back panel, remove the padlock. 3. Locate the cover release latch shown in the illustration. Then, slide the release latch back as you lift the cover. 4. Grip the sides of the computer cover and pivot the cover up using the bottom hinges as leverage points. 5. Remove the cover from the hinge tabs and set it aside on a soft nonabrasive surface.

Dell Desktop Computer (DCCY) — Removing the Computer Cover diagram (page 152)
Fig. 139 · Removing the Computer Cover

1 security cable slot 2 cover release latch 3 computer cover

Page 153 of the Dell Desktop Computer (DCCY) user manual — Power Cable Connectors
Page 153 · click to enlarge
Page 153

Drives

Your computer supports:

l One SATA hard drive

l One floppy drive or Media Card Reader

l One SATA optical drive

Dell Desktop Computer (DCCY) — Drives diagram (page 153)
Fig. 140 · Drives

1 FlexBay for floppy drive or Media Card Reader 2 optical drive 3 hard drive

General Installation Guidelines

1. Connect a SATA hard drive to the connector labeled "SATA0" on the system board (see System Board Components ). 2. Connect the SATA optical drive to the connector labeled "SATA1" on the system board.

Connecting Drive Cables

When you install a drive, you connect two cables—a DC power cable and a data cable—to the back of the drive.

Drive Interface Connectors

Dell Desktop Computer (DCCY) — Drive Interface Connectors diagram (page 153)
Fig. 141 · Drive Interface Connectors

1 interface cable connector 2 interface connector

Interface connectors are keyed for correct insertion.

Power Cable Connectors

Drives · Serial ATA Connector

Page 154 of the Dell Desktop Computer (DCCY) user manual — Removing a Hard Drive
Page 154 · click to enlarge
Page 154

Serial ATA Power Connector

1 power cable 2 power input connector

Connecting and Disconnecting Drive Cables

When connecting and disconnecting a SATA data cable, hold the cable by the black connector at each end.

Hard Drive

Removing a Hard Drive

1. If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. 2. Check the documentation for the drive to verify that it is configured for your computer. 3. Follow the procedures in Before You Begin. 4. Lay the computer on its side so that the system board is on the bottom of the inside of the computer. 5. Press in on the two blue securing tabs on each side of the drive and slide the drive up and out of the computer.

6. Lift the drive out of the computer, careful not to pull the cables still attached to it.
Page 155 of the Dell Desktop Computer (DCCY) user manual — Installing a Hard Drive
Page 155 · click to enlarge
Page 155
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 155)
Fig. 142 · Removing a PCI Card From the Riser-Card Cage

1 securing tabs (2) 2 hard drive

7. Disconnect the power and data cable from the drive.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 155)
Fig. 143 · Removing a PCI Card From the Riser-Card Cage

1 power cable 2 SATA data cable 3 fan cable

8. Disconnect the hard drive fan from the system board.

Installing a Hard Drive

1. Check the documentation for the drive to verify that it is configured for your computer.
2. Unpack the replacement hard drive, and prepare it for installation. 3. If your replacement hard drive does not have the plastic drive bracket attached, remove the bracket from the existing drive by unsnapping it from the drive.
Dell Desktop Computer (DCCY) — Installing a Hard Drive diagram (page 155)
Fig. 144 · Installing a Hard Drive
Page 156 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 156 · click to enlarge
Page 156

1 release tabs (2) 2 drive 3 hard drive bracket

4. Connect the hard drive fan to the system board (see System Board Components ). 5. Connect the power and data cables to the drive.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 156)
Fig. 145 · Removing a PCI Card From the Riser-Card Cage

1 power cable 2 SATA data cable 3 fan cable

6. Gently position the drive until it clicks into place.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 156)
Fig. 146 · Removing a PCI Card From the Riser-Card Cage

1 release tabs (2) 2 hard drive

7. Check all connectors to be certain that they are properly cabled and firmly seated. 8. Replace the computer cover (see Replacing the Computer Cover). 9. If the drive you just installed is the primary drive, insert bootable media into your boot drive. 10. Turn on the computer. 11. Enter system setup (see Entering System Setup) and update the appropriate Primary Drive option (0 or 2). 12. Exit system setup, and reboot the computer. 13. Partition and logically format your drive before you proceed to the next step.

For instructions, see the documentation that came with your operating system.

14. Test the hard drive by running the Dell Diagnostics (see Dell Diagnostics ). 15. Install your operating system on the hard drive.

For instructions, see the documentation that came with your operating system.

Page 157 of the Dell Desktop Computer (DCCY) user manual — Removing an Optical Drive
Page 157 · click to enlarge
Page 157

Replacing a Hard-Drive Fan

1. Follow the instructions in Before You Begin . 2. Remove the hard drive (see Removing a Hard Drive ). 3. Turn the hard drive upside down, so that the hard-drive fan is visible in the bottom of the drive bracket. 4. To remove the hard-drive fan:

a. Lift the release tab on the back panel of the fan. b. Rotate the fan in the opposite direction from that indicated by the arrow on the back panel of the fan. c. Lift to remove the fan and its back panel from the hard-drive bracket.

Dell Desktop Computer (DCCY) — Replacing a Hard-Drive Fan diagram (page 157)
Fig. 147 · Replacing a Hard-Drive Fan

1 fan release tab 2 fan with fan back panel 3 power cable

5. To replace the hard-drive fan:

a. Turn the fan upside-down, so that its backing faces up and align the triangle on the fan's back panel with the corresponding triangle on the back of the hard-drive bracket. b. Rotate the fan and its backing in the direction of the arrow on the fan's back panel. 6. Install the hard drive (see Installing a Hard Drive).

Optical Drive

Removing an Optical Drive

1. Follow the procedures in Before You Begin . 2. Lay the computer on its side so that the system board is on the bottom of the inside of the computer.
3. Pull up on the drive release latch and slide the drive towards the back of the computer. Then lift up to remove the drive from the computer.

4 hard-drive bracket

Page 158 of the Dell Desktop Computer (DCCY) user manual — Installing an Optical Drive
Page 158 · click to enlarge
Page 158
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 158)
Fig. 148 · Removing a PCI Card From the Riser-Card Cage

1 drive release latch 2 optical drive

4. Disconnect the power and data cable from the back of the drive.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 158)
Fig. 149 · Removing a PCI Card From the Riser-Card Cage

1 optical drive 2 data cable 3 power cable

Installing an Optical Drive

1. Unpack the drive and prepare it for installation. 2. Check the documentation that accompanied the drive to verify that the drive is configured for your computer. 3. Connect the power and data cable to the drive.
Dell Desktop Computer (DCCY) — Installing an Optical Drive diagram (page 158)
Fig. 150 · Installing an Optical Drive

1 optical drive 2 data cable 3 power cable

4. Gently position the drive until it clicks into place.
Page 159 of the Dell Desktop Computer (DCCY) user manual — Removing a Floppy Drive or Media Card Reader
Page 159 · click to enlarge
Page 159
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 159)
Fig. 151 · Removing a PCI Card From the Riser-Card Cage

5. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 6. Replace the computer cover (see Replacing the Computer Cover). 7. See the documentation that came with the drive for instructions on installing any software required for drive operation. 8. Enter system setup and select the appropriate Drive option (see Entering System Setup). 9. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics).

Floppy Drive and Media Card Reader

Removing a Floppy Drive or Media Card Reader

1. Follow the procedures in Before You Begin . 2. Lay the computer on its side so that the system board is on the bottom of the inside of the computer. 3. Remove the optical drive and carefully set it aside (see Optical Drive ).
4. If you are removing a floppy drive, pull up the cable release tab to unlock it. 5. Gently lift the data cable from the floppy data cable edge connector.
Page 160 of the Dell Desktop Computer (DCCY) user manual — Installing a Floppy Drive or Media Card Reader
Page 160 · click to enlarge
Page 160
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 160)
Fig. 152 · Removing a PCI Card From the Riser-Card Cage

1 cable release tab 2 data cable edge connector

6. If you are removing a Media Card Reader, disconnect the data cable. 7. If you are removing the Media Card Reader, remove the hard drive (see Removing a Hard Drive ). 8. Disconnect the data cable from the system board.
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 160)
Fig. 153 · Removing a PCI Card From the Riser-Card Cage

1 Media Card Reader data cable

9. Pull up on the drive release latch and slide the floppy drive or Media Card Reader towards the back of the computer. Then lift up to remove the drive or Media Card Reader from the computer.

Installing a Floppy Drive or Media Card Reader

Page 161 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 161 · click to enlarge
Page 161
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 161)
Fig. 154 · Removing a PCI Card From the Riser-Card Cage

1 floppy drive or Media Card Reader 2 screws (3) 3 bracket rails (3)

1. If you are:

l Installing a new floppy drive or Media Card Reader, remove the drive panel insert

l Replacing a drive, remove the floppy drive or Media Card Reader (see Floppy Drive and Media Card Reader).

2. Align the screws on the drive or Media Card Reader with the bracket slots in the computer, and gently position the drive until it clicks into place. 3. If you are installing:

l A floppy drive: insert the data cable into the cable release tab on the floppy drive and press down on the tab until it clicks to lock it in place.

l A Media Card Reader: insert the cable into the connector on the Media Card Reader.

4. If you are installing:

l A floppy drive: insert the data cable into the connector on the system board.

Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 161)
Fig. 155 · Removing a PCI Card From the Riser-Card Cage

1 cable release tab 2 floppy drive data cable edge connector

l A Media Card Reader: remove the hard drive (see Removing a Hard Drive) and connect the cable to the system board connector labeled "USB1

(see System Board Components).

Page 162 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 162 · click to enlarge
Page 162
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 162)
Fig. 156 · Removing a PCI Card From the Riser-Card Cage

1 media card reader data cable

5. Replace the optical drive (see Optical Drive ). 6. Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 7. Replace the computer cover (see Replacing the Computer Cover ). 8. Enter system setup and use the Diskette Drive option to enable your new floppy drive (see System Setup ).

See the documentation that came with the drive for instructions on installing any software required for drive operation.

9. Verify that your computer works correctly by running the Dell Diagnostics (see Dell Diagnostics ).
Page 163 of the Dell Desktop Computer (DCCY) user manual — Notes, Notices, and Cautions
Page 163 · click to enlarge
Page 163

Dell™ OptiPlex™ 740 User's Guide

Small Form Factor Computer

About Your Computer Finding Information Small Form Factor Computer Small Form Factor Computer (Model # DCCY) Specifications Advanced Features Cleaning Your Computer Reinstalling Drivers and the Operating System Solving Problems Microsoft® Windows® XP and Windows Vista® Features Troubleshooting Tools and Utilities Getting Help Warranty FCC Regulatory Model (U.S. Only) Glossary

Removing and Replacing Parts Before You Begin Removing the Computer Cover Chassis Intrusion Switch I/O Panel Drives PCI, PCI Express Cards, and PS/2 Serial Port Adapters Power Supply Processor Battery Replacing the System Board Memory Replacing the Computer Cover

ModelsDCSM, DCNE, and DCCY

Notes, Notices, and Cautions

Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, OptiPlex, Inspiron, Dimension, Latitude, Dell Precision, DellNet, TravelLite, Dell OpenManage, PowerVault, Axim, PowerEdge, PowerConnect, and PowerApp are trademarks of Dell Inc.; AMD, AMD Athlon, AMD Phenom, and combinations thereof, and Cool 'n' Quiet are trademarks of Advanced Micro Devices, Inc; Microsoft and Windows are registered trademarks of Microsoft Corporation; IBM is a registered trademark of International Business Machines Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

March 2008 RP699 Rev. A03

Page 164 of the Dell Desktop Computer (DCCY) user manual — Dell™ Optiplex™ 740 Systems User's Guide
Page 164 · click to enlarge
Page 164

Dell™ Optiplex™ 740 Systems User's Guide

I/O Panel

Removing the I/O Panel

1. Follow the procedures in Before You Begin . 2. Remove the optical drive and floppy drive or Media Card Reader from the drive bays, if installed (see Drives ). 3. Remove the processor heat sink (see Processor ). 4. Remove the front fan:

a. Disconnect the fan connector. b. Disconnect the fan control cable. c. Press the tab that secures the fan to the interior base of the computer and lift the fan from the computer; set the fan aside in the chassis.

Dell Desktop Computer (DCCY) — Dell™ Optiplex™ 740 Systems User's Guide diagram (page 164)
Fig. 157 · Dell™ Optiplex™ 740 Systems User's Guide

1 fan control ribbon cable 2 fan release tab 3 fan cable

5. Disconnect all cables that are connected to the I/O panel that you can access without removing the I/O panel.

I/O Panel

Page 165 of the Dell Desktop Computer (DCCY) user manual — Replacing the I/O Panel
Page 165 · click to enlarge
Page 165
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 165)
Fig. 158 · Removing a PCI Card From the Riser-Card Cage

1 fan cable connector 2 air temperature sensor cable 3 I/O cable connector

4 screw 5 I/O panel

6. From inside the computer cover, remove the mounting screw that secures the I/O panel to the computer. 7. Ease the I/O panel back and forth to release its circular tabs from the two holes in the chassis that secure it. 8. Remove any remaining cables; note the routing of all cables, so that you can reroute them 9. Remove the I/O panel from the computer.

Replacing the I/O Panel

1. To replace the I/O panel, follow the removal procedures in the reverse order.
Page 166 of the Dell Desktop Computer (DCCY) user manual — Dell™ Optiplex™ 740 Systems User's Guide
Page 166 · click to enlarge
Page 166

Dell™ Optiplex™ 740 Systems User's Guide

Power Supply

Replacing the Power Supply

1. Follow the procedures in Before You Begin . 2. If installed, remove the optical drive (see Removing an Optical Drive ). 3. If installed, remove the floppy drive or Media Card Reader (see Removing a Floppy Drive or Media Card Reader ). 4. Disconnect the DC power cables from the system board and the drives.
5. Remove the three screws that attach the power supply to the computer chassis.
Dell Desktop Computer (DCCY) — Dell™ Optiplex™ 740 Systems User's Guide diagram (page 166)
Fig. 159 · Dell™ Optiplex™ 740 Systems User's Guide

1 power supply 2 screw

6. Slide the power supply toward the front of the computer approximately 1 inch. 7. Lift the power supply up and out of the computer. 8. Slide the replacement power supply into place. 9. Replace the screws that secure the power supply to the back of the computer chassis. 10. Reconnect the DC power cables to the system board and drives (see System Board Components for connector locations). 11. Replace the floppy drive or Media Card Reader (see Installing a Floppy Drive or Media Card Reader).

Power Supply

Page 167 of the Dell Desktop Computer (DCCY) user manual — DC Power Connector P1
Page 167 · click to enlarge
Page 167
12. Replace the optical drive (see Installing an Optical Drive ). 13. Replace the computer cover (see Replacing the Computer Cover ). 14. Connect the AC power cable to the power supply AC power connector.
15. Connect your computer and devices to electrical outlets, and turn them on.

DC Power Connectors

Dell Desktop Computer (DCCY) — DC Power Connectors diagram (page 167)
Fig. 160 · DC Power Connectors

DC Power Connector P1

Dell Desktop Computer (DCCY) — DC Power Connector P1 diagram (page 167)
Fig. 161 · DC Power Connector P1
Dell Desktop Computer (DCCY) — DC Power Connector P1 diagram (page 167)
Fig. 162 · DC Power Connector P1
Page 168 of the Dell Desktop Computer (DCCY) user manual — DC Power Connector P5
Page 168 · click to enlarge
Page 168
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 168)
Fig. 163 · Removing a PCI Card From the Riser-Card Cage

DC Power Connector P2

Dell Desktop Computer (DCCY) — DC Power Connector P2 diagram (page 168)
Fig. 164 · DC Power Connector P2

DC Power Connectors P3

Dell Desktop Computer (DCCY) — DC Power Connectors P3 diagram (page 168)
Fig. 165 · DC Power Connectors P3

DC Power Connector P5

Dell Desktop Computer (DCCY) — DC Power Connector P5 diagram (page 168)
Fig. 166 · DC Power Connector P5
Page 169 of the Dell Desktop Computer (DCCY) user manual — Small Form Factor Computer (Model # DCCY) Specifications
Page 169 · click to enlarge
Page 169

Dell™ Optiplex™ 740 Systems User's Guide

Small Form Factor Computer (Model # DCCY) Specifications

Small Form Factor Computer (Model # DCCY) Specifications

Microprocessor type AMD Phenom™ processors

AMD Athlon™ 64 X2 Dual-Core processor

Internal cache AMD Phenom Quad-Core2-MB L2 dedicated cache and 2-MB shared L3 cache
AMD Phenom Triple-Core1.5-MB L2 dedicated cache and 2-MB shared L3 cache
AMD Athlon 64 X22-MB L2 dedicated cache

AMD Athlon 64 X2:1-MB L2 dedicated cache

AMD Athlon1-MB L2 dedicated cache
AMD Athlon512-KB L2 dedicated cache

Type 667- or 800-MHz DDR2 SDRAM

Memory modules supported 256 MB, 512 MB, 1 GB, or 2 GB non-ECC

Minimum memory dual-channel512 MB; single-channel: 256 MB

Maximum memory 8 GB

Chipset nVidia GeForce 6150LE/NForce 430

Data bus width 64 bits

Address bus width 40 bits

BIOS chip (NVRAM) 8 Mb or 4 Mb

NIC integrated network interface with ASF 1.03 and 2.0 support as defined by DMTF

Capable of 10/100/1000 communication

Show 7 more labels / short text on this page
Microprocessor · AMD Athlon 64 · Memory · Memory connectors 4 · Computer Information · DMA channels eight · Interrupt levels 24
Page 170 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 170 · click to enlarge
Page 170
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 170)
Fig. 167 · Removing a PCI Card From the Riser-Card Cage

Type nVidia integrated video (DirectX 9.0c Shader Model 3.0 Graphics Processing Unit), PCI Express x16 graphics card, or DVI graphics card.

Bus type PCI 2.3 PCI Express 1.0A SATA 1.0A and 2.0 USB 2.0

PCI Express x16: 40 GB/s bidirectional speed SATA: 1.5 Gbps and 3.0 Gbps USB: 480-Mbps high speed, 12-Mbps full speed, 1.2- Mbps low speed

connector data width (maximum) 16 PCI Express lanes (x16)

Externally accessible one 3.5-inch drive one bay for slim optical drive

Internally accessible one bay for a 1-inch-high hard drive

Page 171 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 171 · click to enlarge
Page 171

USB two front-panel and five back-panel USB 2.0– compliant connectors

Audio two connectors for line-in and line-out; two front- panel connectors for headphones and microphone

System board connectors:

SATA two 7-pin connectors

Floppy drive 38-pin connector

Serial 24-pin connector for optional second serial port card

Fan two 5-pin connector fans

PCI 2.3 124-pin connector

Internal USB 10-pin connector

Intrusion switch 3-pin connector

Memory modules four 240-pin connectors

Power 12V 4-pin connector

Front panel 40-pin connector

in Microsoft® Windows® XP and Windows Vista, brings up the Windows Security window; in MS-DOS® mode, restarts (reboots) the computer

or starts embedded system setup (during system start- up only)

or displays a boot device menu that allows the user to enter a device for a single boot (during system start- up only) as well as options to run hard-drive and system diagnostics

Power control front of chassis - push button

Power light (within the power button) green light — Blinking green indicates a sleep mode; solid green indicates a power-on state.

amber light — Blinking amber indicates a problem with an installed device; solid amber indicates an internal power problem (see Power Problems).

Hard-drive access light front panel - green

Link light front panel - solid green light indicates network connection

Link integrity light (on integrated network adapter) rear panel - green light for 10-Mb operation; orange light for 100-Mb operation; yellow light for a 1000-Mb (1-Gb) operation

Activity light (on integrated network adapter) rear panel - yellow blinking light

Diagnostic lights front panel - four lights. See Diagnostic Lights.

Standby power light AUX_PWR on the system board

DC power supply:

Heat dissipation 938.85 BTU/hr maximum

Voltage manual selection power supplies — 90 to 135 V at 50/60 Hz; 180 to 265 V at 50/60 Hz

Backup battery 3-V CR2032 lithium coin cell

Height 9.26 cm (3.65 inches)

Width 31.37 cm (12.35 inches)

Depth 34.03 cm (13.40 inches)

Show 9 more labels / short text on this page
PCIe-X16 164-pin connector · Speaker 5-pin connector · Power 24-pin connector · Battery 2-pin socket · Key Combinations · Controls and Lights · Power · Wattage 275 W · Physical
Page 172 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 172 · click to enlarge
Page 172

Weight 7.4 kg (16.4 lb)

Temperature:

Operating 10° to 35°C (50° to 95°F)

Storage –40° to 65°C (–40° to 149°F)

Relative humidity 20% to 80% (noncondensing)

Maximum vibration:

Operating 0.25 G at 3 to 200 Hz at 0.5 octave/min

Storage 0.5 G at 3 to 200 Hz at 1 octave/min

Maximum shock:

Operating bottom half-sine pulse with a change in velocity of 50.8 cm/sec (20 inches/sec)

Storage 27-G faired square wave with a velocity change of 508 cm/sec (200 inches/sec)

Altitude:

Operating –15.2 to 3048 m (–50 to 10,000 ft)

Storage –15.2 to 10,668 m (–50 to 35,000 ft)

Airborne contaminant level G2 or lower as defined by ISA-S71.04-1985

Environmental

Page 173 of the Dell Desktop Computer (DCCY) user manual — Removing a Speaker
Page 173 · click to enlarge
Page 173

Dell™ Optiplex™ 740 Systems User's Guide

Speaker

Installing a Speaker

1. Follow the procedures in Before You Begin . 2. Remove the cover of your computer (see Removing the Computer Cover ). 3. Attach the speaker to the system fan in the chassis of the computer.
4. Connect the cables to the system board. 5. Replace the computer cover. 6. Turn on power to the computer.

Removing a Speaker

1. Follow the procedures in Before You Begin . 2. Remove the cover of your computer (see Removing the Computer Cover ). 3. Disconnect the cables from the system board. 4. Remove the speaker from the system fan in the chassis of the computer.
5. Replace the computer cover. 6. Turn on power to the computer.

Speaker

Page 174 of the Dell Desktop Computer (DCCY) user manual — About Your Small Form Factor Computer
Page 174 · click to enlarge
Page 174

Small Form Factor Computer

Dell™ Optiplex™ 740 Systems User's Guide

About Your Small Form Factor Computer

About Your Small Form Factor Computer

Front View

Dell Desktop Computer (DCCY) — About Your Small Form Factor Computer diagram (page 174)
Fig. 168 · About Your Small Form Factor Computer

1 USB 2.0 connectors (2)

Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see System Setup for more information about booting to a USB device).

It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

2 power button Press to turn on the computer.

3 Dell badge This badge can be rotated to match the orientation of your computer. To rotate, place fingers around the outside of the badge, press firmly, and turn the badge. You can also rotate the badge using the slot provided near the bottom of the badge.

4 hard drive activity light

This light flickers when the hard drive is being accessed.

Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see Diagnostic Lights.

6 LAN indicator light

This light indicates that a LAN (local area network) connection is established.

7 power light The power light illuminates and blinks or remains solid to indicate different operating states:

l No light — The computer is turned off.

l Steady green — The computer is in a normal operating state.

l Blinking green — The computer is in a power-saving mode.

l Blinking or solid amber — See Power Problems.

To exit from a power-saving mode, press the power button or use the keyboard or the mouse if it is configured as a wake device in the Windows Device Manager. For more information about sleep modes and exiting from a power-saving mode, see Power Management.

See System Lights for a description of light codes that can help you troubleshoot problems with your computer.

Use the headphone connector to attach headphones and most kinds of speakers.

9 microphone Use the microphone connector to attach a microphone.

Inside Your Computer · 5 diagnostic lights · 8 headphone connector

Page 175 of the Dell Desktop Computer (DCCY) user manual — Back-Panel Connectors
Page 175 · click to enlarge
Page 175

10 3.5-inch drive bay

Can contain an optional slimline floppy drive or optional slimline media card reader.

11 optical drive Insert a slimline media (if supported) into this drive.

Back View

Dell Desktop Computer (DCCY) — Back View diagram (page 175)
Fig. 169 · Back View

1 card slots Access connectors for any installed PCI and PCI Express cards.

Plug serial, USB, and other devices into the appropriate connectors (see Back-Panel Connectors).

Insert the power cable.

4 voltage selection switch

Your computer is equipped with a manual voltage-selection switch. To help avoid damaging a computer with a manual voltage selection switch, set the switch for the voltage that most closely matches the AC power available in your location.

Also, ensure that your monitor and attached devices are electrically rated to operate with the AC power available in your location.

5 padlock ring Insert a padlock to lock the computer cover.

6 cover release latch

Allows you to open the computer cover.

Back-Panel Connectors

Dell Desktop Computer (DCCY) — Back-Panel Connectors diagram (page 175)
Fig. 170 · Back-Panel Connectors

Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.

2 link integrity light

l Green — A good connection exists between a 10-Mbps network and

the computer.

l Orange — A good connection exists between a 100-Mbps network

and the computer.

l Yellow — A good connection exists between a 1-Gbps (or 1000-

Mbps) network and the computer.

l Off — The computer is not detecting a physical connection to the

network.

3 network adapter connector

To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the

Show 4 more labels / short text on this page
connector · 2 back-panel connectors · 3 power connector · 1 parallel connector
Page 176 of the Dell Desktop Computer (DCCY) user manual — Inside Your Computer
Page 176 · click to enlarge
Page 176

network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached.

On computers with a network connector card, use the connector on the card.

It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.

4 network activity light

Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.

Use the green line-out connector to attach headphones and most speakers with integrated amplifiers.

On computers with a sound card, use the connector on the card.

Use the line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR.

On computers with a sound card, use the connector on the card.

7 USB 2.0 connectors (5)

Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

Plug the cable from your VGA-compatible monitor into the blue connector.

Connect a serial device, such as a handheld device, to the serial port. The default designations are COM1 for serial connector 1 and COM2 for serial connector 2.

For more information, see System Setup Options.

Inside Your Computer

Show 4 more labels / short text on this page
5 line-out connector · 6 line-in connector · 8 video connector · 9 serial connector
Page 177 of the Dell Desktop Computer (DCCY) user manual — System Board Components
Page 177 · click to enlarge
Page 177
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 177)
Fig. 171 · Removing a PCI Card From the Riser-Card Cage

1 drive-release latch 2 optical drive 3 power supply

4 chassis intrusion switch (optional) 5 hard drive 6 card slots (2)

7 system board 8 heat sink assembly

System Board Components

Dell Desktop Computer (DCCY) — System Board Components diagram (page 177)
Fig. 172 · System Board Components
Dell Desktop Computer (DCCY) — System Board Components diagram (page 177)
Fig. 173 · System Board Components

10 CMOS reset jumper (RTCRST) 11 battery socket (BATTERY)

13 standby (AUX_PWR_LED) 14 PCI Express x16 connector (SLOT1)

Page 178 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 178 · click to enlarge
Page 178

19 Optional DVI-card connector (DVI_HDR)

20 speaker connector (INT_SPKR)

Page 179 of the Dell Desktop Computer (DCCY) user manual — Identifying Drivers
Page 179 · click to enlarge
Page 179

Reinstalling Drivers and the Operating System

Dell™ Optiplex™ 740 Systems User's Guide

Restoring Your Operating System

Reinstalling Microsoft® Windows Vista® and Windows® XP

Drivers

What Is a Driver?

A driver is a program that controls a device such as a printer, mouse, or keyboard. All devices require a driver program.

A driver acts like a translator between the device and any other programs that use the device. Each device has its own set of specialized commands that only its driver recognizes.

Dell ships your computer to you with required drivers already installed—no further installation or configuration is needed.

Many drivers, such as the keyboard driver, come with your Microsoft Windows operating system. You may need to install drivers if you:

l Upgrade your operating system.

l Reinstall your operating system.

l Connect or install a new device.

Identifying Drivers

If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver.

If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver.

1. Click Start , and right-click Computer . 2. Click Properties ® Device Manager .

Scroll down the list to see if any device has an exclamation point (a yellow circle with a [!]) on the device icon.

If an exclamation point is next to the device name, you may need to reinstall the driver or install a new driver (see Reinstalling Drivers and Utilities).

1. Click the Start button and click Control Panel . 2. Under Pick a Category , click Performance and Maintenance . 3. Click System . 4. In the System Properties window, click the Hardware tab. 5. Click Device Manager .

Drivers · Windows Vista · Windows XP

Page 180 of the Dell Desktop Computer (DCCY) user manual — Using the Optional Drivers and Utilities media
Page 180 · click to enlarge
Page 180
6. Scroll down the list to see if any device has an exclamation point (a yellow circle with a [ ! ]) on the device icon.

If an exclamation point is next to the device name, you may need to reinstall the driver or install a new driver.

Reinstalling Drivers and Utilities

Using Windows Vista Device Driver Rollback

If a problem occurs on your computer after you install or update a driver, use Windows Device Driver Rollback to replace the driver with the previously installed version.

1. Click Start , and right-click Computer . 2. Click Properties ® Device Manager .
3. Right-click the device for which the new driver was installed and click Properties . 4. Click the Drivers tab ® Roll Back Driver .

If Device Driver Rollback does not resolve the problem, then use System Restore (see Restoring Your Operating System) to return your computer to the operating state that existed before you installed the new driver.

Using Windows XP Device Driver Rollback

If a problem occurs on your computer after you install or update a driver, use Windows XP Device Driver Rollback to replace the driver with the previously installed version.

1. Click the Start button and click Control Panel . 2. Under Pick a Category , click Performance and Maintenance . 3. Click System . 4. In the System Properties window, click the Hardware tab. 5. Click Device Manager . 6. Right-click the device for which the new driver was installed and click Properties . 7. Click the Drivers tab. 8. Click Roll Back Driver .

If Device Driver Rollback does not resolve the problem, then use System Restore (see Enabling System Restore), to return your computer to the operating state that existed before you installed the new driver.

Using the Optional Drivers and Utilities media

If using Device Driver Rollback or System Restore does not resolve your problem, (see Restoring Your Operating System), then reinstall the driver from the Drivers and Utilities media.

1. Save and close any open files, and exit any open programs.

Windows Vista

Page 181 of the Dell Desktop Computer (DCCY) user manual — Using the Windows XP Drivers and Utilities Media
Page 181 · click to enlarge
Page 181
2. Insert the Drivers and Utilities media.

In most cases, the CD/DVD starts running automatically. If it does not, start Windows Explorer, click your CD/DVD drive directory to display the CD/DVD contents, and then double-click the autorcd.exe file. The first time that you run the CD/DVD, it might prompt you to install setup files. Click OK, and follow the instructions on the screen to continue.

3. From the Language drop-down menu in the toolbar, select your preferred language for the driver or utility (if available). 4. At the welcome screen, click Next and wait for the CD/DVD to complete the hardware scan. 5. To detect other drivers and utilities, under Search Criteria , select the appropriate categories from the System Model , Operating System , and Topic drop-down menus.

A link or links appear(s) for the specific drivers and utilities used by your computer.

6. Click the link of a specific driver or utility to display information about the driver or utility that you want to install. 7. Click the Install button (if present) to begin installing the driver or utility. At the welcome screen, follow the screen prompts to complete the installation. 8. At the welcome screen, follow the screen prompts to complete the installation.

If no Install button is present, automatic installation is not an option. For installation instructions, either see the appropriate instructions in the following subsections, or click Extract, follow the extracting instructions, and then read the readme file.

If instructed to navigate to the driver files, click the CD/DVD directory on the driver information window to display the files associated with that driver.

Manually Reinstalling Drivers for Windows Vista

After extracting the driver files to your hard drive as described in the previous section, do the following:

1. Click Start , and right-click Computer . 2. Click Properties ® Device Manager .

3. Double-click the type of device for which you are installing the driver (for example, Audio or Video). 4. Double-click the name of the device for which you are installing the driver. 5. Click Driver® Update Driver® Browse my computer for driver software. 6. Click Browse and browse to the location to which you previously copied the driver files. 7. When the name of the appropriate driver appears, click the name of the driver® OK® Next. 8. Click Finish and restart your computer.

Using the Windows XP Drivers and Utilities Media

1. Insert the Drivers and Utilities media .

If this is your first time to use the Drivers and Utilities media, the Installation window opens to inform you that the media will begin the installation. Click OK and respond to the installation program prompts to complete the installation.

2. Click Next at the Welcome Dell System Owner screen. 3. Choose the appropriate selections for System Model , Operating System , Device Type , and Topic . 4. Click My Drivers in the Topic drop-down menu.

The Drivers and Utilities media scans your computer's hardware and operating system and then displays a list of device drivers for your system configuration.

5. Click the appropriate driver and follow the instructions to download the driver for your computer.
Page 182 of the Dell Desktop Computer (DCCY) user manual — Restoring the Computer to an Earlier Operating State
Page 182 · click to enlarge
Page 182

To view a list of all available drivers for your computer, click Drivers in the Topic drop-down menu.

To access the help files on the Drivers and Utilities media, click the question mark button or the Help link at the top of the screen.

Restoring Your Operating System

The Microsoft Windows operating system provides System Restore to allow you to return your computer to an earlier operating state (without affecting data files) if changes to the hardware, software, or other system settings have left the computer in an undesirable operating state. See the Windows Help and Support Center for information on using System Restore.

Windows Vista

Starting System Restore

1. Click Start . 2. In the Start Search box, type System Restore and press .
3. Click Next and follow the remaining prompts on the screen.

In the event that System Restore did not resolve the issue, you may undo the last system restore.

Undoing the Last System Restore

1. Click Start . 2. In the Start Search box, type System Restore and press . 3. Click Undo my last restoration and click Next .

Windows XP

Creating a Restore Point

1. Click the Start button and click Help and Support . 2. Click System Restore . 3. Follow the instructions on the screen.

Restoring the Computer to an Earlier Operating State

1. Click the Start button, point to All Programs ® Accessories ® System Tools , and then click System Restore . 2. Ensure that Restore my computer to an earlier time is selected and click Next .
Page 183 of the Dell Desktop Computer (DCCY) user manual — Reinstalling Microsoft ® Windows Vista ® and Windows ® XP
Page 183 · click to enlarge
Page 183
3. Click a calendar date to which you want to restore your computer.

The Select a Restore Point screen provides a calendar that allows you to see and select restore points. All calendar dates with available restore points appear in boldface type.

4. Select a restore point and click Next .

If a calendar date has only one restore point, then that restore point is automatically selected. If two or more restore points are available, click the restore point that you prefer.

5. Click Next .

The Restoration Complete screen appears after System Restore finishes collecting data and then the computer restarts.

6. After the computer restarts, click OK .

To change the restore point, you can either repeat the steps using a different restore point, or you can undo the restoration.

Undoing the Last System Restore

1. Click the Start button, point to All Programs ® Accessories ® System Tools , and then click System Restore . 2. Click Undo my last restoration and click Next . 3. Click Next .

The System Restore screen appears and the computer restarts.

4. After the computer restarts, click OK .

Enabling System Restore

If you reinstall Windows XP with less than 200 MB of free hard-disk space available, System Restore is automatically disabled. To see if System Restore is enabled:

1. Click the Start button and click Control Panel . 2. Click Performance and Maintenance . 3. Click System . 4. Click the System Restore tab. 5. Ensure that Turn off System Restore is unchecked.

Reinstalling Microsoft ® Windows Vista ® and Windows ® XP

The reinstallation process can take 1 to 2 hours to complete. After you reinstall the operating system, you must also reinstall the device drivers, virus protection program, and other software.

1. Save and close any open files and exit any open programs. 2. Insert the Operating System disc. 3. Click Exit if the Install Windows message appears. 4. Restart the computer.

When the DELL logo appears, press immediately.

Windows Vista

Page 184 of the Dell Desktop Computer (DCCY) user manual — Windows XP Setup
Page 184 · click to enlarge
Page 184
5. When the boot device list appears, highlight CD/DVD/CD-RW Drive and press . 6. Press any key to Boot from CD-ROM . 7. Follow the instructions on the screen to complete the installation.

Before You Begin

If you are considering reinstalling the Windows XP operating system to correct a problem with a newly installed driver, first try using Windows XP Device Driver Rollback (see Using Windows XP Device Driver Rollback). If Device Driver Rollback does not resolve the problem, then use System Restore (see Restoring Your Operating System) to return your operating system to the operating state it was in before you installed the new device driver.

To reinstall Windows XP, you need the following items:

l Dell™ Operating System media

l Dell Drivers and Utilities media

To reinstall Windows XP, perform all the steps in the following sections in the order in which they are listed.

The reinstallation process can take 1 to 2 hours to complete. After you reinstall the operating system, you must also reinstall the device drivers, virus protection program, and other software.

Booting From the Operating System Media

1. Save and close any open files and exit any open programs. 2. Insert the Operating System media. Click Exit if Install Windows XP message appears. 3. Restart the computer. 4. Press immediately after the DELL™ logo appears.

If the operating system logo appears, wait until you see the Windows desktop, and then shut down the computer and try again.

5. Press the arrow keys to select CD-ROM , and press . 6. When the Press any key to boot from CD message appears, press any key.

Windows XP Setup

1. When the Windows XP Setup screen appears, press to select To set up Windows now. 2. Read the information on the Microsoft Windows Licensing Agreement screen, and press to accept the license agreement. 3. If your computer already has Windows XP installed and you want to recover your current Windows XP data, type r to select the repair option, and remove the media. 4. If you want to install a new copy of Windows XP, press to select that option.

Windows XP

Page 185 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 185 · click to enlarge
Page 185
5. Press to select the highlighted partition (recommended), and follow the instructions on the screen.

The Windows XP Setup screen appears, and the operating system begins to copy files and install the devices. The computer automatically restarts multiple times.

6. When the Regional and Language Options screen appears, select the settings for your location and click Next. 7. Enter your name and organization (optional) in the Personalize Your Software screen, and click Next. 8. At the Computer Name and Administrator Password window, enter a name for your computer (or accept the one provided) and a password, and click Next. 9. If the Modem Dialing Information screen appears, enter the requested information and click Next. 10. Enter the date, time, and time zone in the Date and Time Settings window, and click Next. 11. If the Networking Settings screen appears, click Typical and click Next. 12. If you are reinstalling Windows XP Professional and you are prompted to provide further information regarding your network configuration, enter your selections. If you are unsure of your settings, accept the default selections.

Windows XP installs the operating system components and configures the computer. The computer automatically restarts.

13. When the Welcome to Microsoft screen appears, click Next. 14. When the How will this computer connect to the Internet? message appears, click Skip. 15. When the Ready to register with Microsoft? screen appears, select No, not at this time and click Next. 16. When the Who will use this computer? screen appears, you can enter up to five users. 17. Click Next. 18. Click Finish to complete the setup, and remove the media. 19. Reinstall the appropriate drivers with the Drivers and Utilities media. 20. Reinstall your virus protection software. 21. Reinstall your programs.

Page 186 of the Dell Desktop Computer (DCCY) user manual — Card Problems
Page 186 · click to enlarge
Page 186

Solving Problems

Dell™ OptiPlex™ 740 Systems User's Guide

E-Mail, Modem, and Internet Problems

Serial or Parallel Device Problems

Lockups and Software Problems

Sound and Speaker Problems

Media Card Reader Problems

Video and Monitor Problems

Troubleshooting Tips

Follow these tips when you troubleshoot your computer:

l If you added or removed a part before the problem started, review the installation procedures and ensure that the part is correctly installed.

l If a peripheral device does not work, ensure that the device is properly connected.

l If an error message appears on the screen, write down the exact message. This message may help technical support personnel diagnose and fix the

problem(s).

l If an error message occurs in a program, see the program's documentation.

Battery Problems

Fill out the Diagnostics Checklist as you complete these checks.

Replace the battery — If you have to repeatedly reset time and date information after turning on the computer, or if an incorrect time or date displays during start-up, replace the battery (see Replacing the Battery). If the battery still does not work properly, contact Dell (see Contacting Dell).

Card Problems

Fill out the Diagnostics Checklist as you complete these checks.

Check the card seating and cable —

1. Turn off the computer and devices, disconnect them from their electrical outlets, wait 10 to 20 seconds, and then remove the computer cover (see Removing the Computer Cover for mini tower computers, or Removing the Computer Cover for desktop computers). 2. Ensure that each card is firmly seated in its connector. Reseat any loose cards. 3. Ensure that all cables are firmly connected to their corresponding connectors on the cards. If any cables appear loose, reconnect them.

For instructions on which cables should be attached to specific connectors on a card, see the card's documentation.

4. Close the computer cover (see Replacing the Computer Cover ), reconnect the computer and devices to electrical outlets, and then
Show 12 more labels / short text on this page
Troubleshooting Tips · Memory Problems · Battery Problems · Mouse Problems · Card Problems · Network Problems · Drive Problems · Power Problems · Printer Problems · Keyboard Problems · Restoring Default Settings · Fan Problems
Page 187 of the Dell Desktop Computer (DCCY) user manual — CD and DVD drive problems
Page 187 · click to enlarge
Page 187

turn them on.

Test the graphics card —

1. Turn off the computer and devices, disconnect them from their electrical outlets, wait 10 to 20 seconds, and then remove the computer cover (see Removing the Computer Cover for mini tower computers, or Removing the Computer Cover for desktop computers). 2. Remove all cards except the graphics card (see PCI, PCI Express Cards, and PS/2 Serial Port Adapters for mini tower computers, or Removing a PCI Card for desktop computers).

If your primary hard drive is connected to a drive controller card leave the drive controller card installed in the computer.

3. Close the computer cover (see Replacing the Computer Cover ), reconnect the computer and devices to electrical outlets, and then turn them on. 4. Run the Dell Diagnostics (see Dell Diagnostics ).

Test the cards —

1. Turn off the computer and devices, disconnect them from their electrical outlets, wait 10 to 20 seconds, and then remove the computer cover (see Removing the Computer Cover for mini tower computers, or Removing the Computer Cover for desktop computers). 2. Reinstall one of the cards that you removed previously (see PCI, PCI Express Cards, and PS/2 Serial Port Adapters for mini tower computers, or Installing a PCI Card for desktop computers). 3. Close the computer cover, (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on. 4. Run the Dell Diagnostics (see Dell Diagnostics). 5. If any of the tests fail, the card you just reinstalled is faulty and needs to be replaced. 6. Repeat this process until you have reinstalled all cards.

Drive Problems

Fill out the Diagnostics Checklist as you complete these checks.

Test the drive —

l Insert another floppy disk, CD, or DVD to eliminate the possibility that the original one is defective.

l Insert bootable media and restart the computer.

Clean the drive or disk — See CDs and DVDs.

Check the cable connections

Check for Software and Hardware Conflicts — See Resolving Software and Hardware Incompatibilities.

Run the Dell Diagnostics — See Dell Diagnostics.

CD and DVD drive problems

Adjust the Windows volume control —

Page 188 of the Dell Desktop Computer (DCCY) user manual — Keyboard Problems
Page 188 · click to enlarge
Page 188

l Click the speaker icon in the lower-right corner of your screen.

l Ensure that the volume is turned up by clicking the slidebar and dragging it up.

l Ensure that the sound is not muted by clicking any boxes that are checked.

Check the speakers and subwoofer — See Sound and Speaker Problems.

Problems writing to an Optical-RW drive

Close other programs — The Optical-RW drive must receive a steady stream of data when writing. If the stream is interrupted, an error occurs. Try closing all programs before you write to the Optical-RW.

Turn off Standby mode in Windows before writing to a Optical-RW disc — See your computer documentation for information on Power Management modes (see Power Management).

Hard drive problems

Run Check Disk —

1. Click the Start button and click My Computer . 2. Right-click Local Disk C: . 3. Click Properties . 4. Click the Tools tab. 5. Under Error-checking , click Check Now . 6. Click Scan for and attempt recovery of bad sectors . 7. Click Start .

E-Mail, Modem, and Internet Problems

Run the Modem Helper diagnostics — Click the Start button, point to All Programs, and then click Modem Helper. Follow the instructions on the screen to identify and resolve modem problems. (Modem Helper is not available on all computers.)

Verify that the modem is communicating with Windows —

1. Click the Start button and click Control Panel . 2. Click Printers and Other Hardware . 3. Click Phone and Modem Options . 4. Click the Modems tab. 5. Click the COM port for your modem. 6. Click Properties , click the Diagnostics tab, and then click Query Modem to verify that the modem is communicating with Windows.

If all commands receive responses, the modem is operating properly.

Ensure that you are connected to the Internet — Ensure that you have subscribed to an Internet provider. With the Outlook Express e- mail program open, click File. If Work Offline has a checkmark next to it, click the checkmark to remove it and connect to the Internet. For help, contact your Internet service provider.

Keyboard Problems

Page 189 of the Dell Desktop Computer (DCCY) user manual — A program stops responding
Page 189 · click to enlarge
Page 189

Check the keyboard cable —

l Ensure that the keyboard cable is firmly connected to the computer.

l Shut down the computer, reconnect the keyboard cable as shown in the Quick Reference Guide for your computer, and then restart the

computer.

l Check the cable connector for bent or broken pins and for damaged or frayed cables. Straighten bent pins.

l Remove keyboard extension cables and connect the keyboard directly to the computer.

Test the keyboard — Connect a properly working keyboard to the computer, and try using the keyboard. If the new keyboard works, the original keyboard is faulty.

Run the Dell Diagnostics — See Dell Diagnostics.

Check for software and hardware conflicts — See Resolving Software and Hardware Incompatibilities.

Fan Problems

Check the cable connections — Ensure that the card fan cable is connected firmly to the card fan connector on the system board (see System Board Components for mini tower computers, and System Board Components for desktop computers).

Lockups and Software Problems

The computer does not start up

Check the Diagnostic Lights — See Diagnostic Lights.

Ensure that the power cable is firmly connected to the computer and to the electrical outlet

The computer stops responding

Turn the computer off — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Then restart your computer.

A program stops responding

Page 190 of the Dell Desktop Computer (DCCY) user manual — Media Card Reader Problems
Page 190 · click to enlarge
Page 190

End the program —

1. Press simultaneously. 2. Click Applications . 3. Click the program that is no longer responding. 4. Click End Task .

A program crashes repeatedly

Check the software documentation — If necessary, uninstall and then reinstall the program.

A solid blue screen appears

Turn the computer off — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Then restart your computer.

Other software problems

Check the software documentation or contact the software manufacturer for troubleshooting information —

l Ensure that the program is compatible with the operating system installed on your computer.

l Ensure that your computer meets the minimum hardware requirements needed to run the software. See the software documentation

for information.

l Ensure that the program is installed and configured properly.

l Verify that the device drivers do not conflict with the program.

l If necessary, uninstall and then reinstall the program.

Back up your files immediately

Use a virus-scanning program to check the hard drive, floppy disks, or CDs

Save and close any open files or programs and shut down your computer through the Start menu

Run the Dell Diagnostics — If all tests run successfully, the error condition is related to a software problem (see Dell Diagnostics).

Media Card Reader Problems

No drive letter is assigned —

When Microsoft Windows XP detects the media card reader, the device is automatically assigned a drive letter as the next logical drive after all other physical drives in the system. If the next logical drive after the physical drives is mapped to a network drive, Windows XP does not automatically assign a drive letter to the media card reader.

To manually assign a drive for the media card reader:

1. Right-click My Computer and select Manage . 2. Select the Disk Management option. 3. Right-click the corresponding drive letter in the right pane that needs to be changed. 4. Select Drive Letter and Paths. 5. From the drop-down list, select the new drive letter assignment for the media card reader. 6. Click OK to confirm your selection.
Page 191 of the Dell Desktop Computer (DCCY) user manual — Mouse Problems
Page 191 · click to enlarge
Page 191

FlexBay device is Disabled —

There is a FlexBay disable option in the BIOS setup that appears only when the FlexBay device is installed. If the FlexBay device is physically installed, but it is not running, check to see if it is enabled in the BIOS setup.

Memory Problems

Fill out the Diagnostics Checklist as you complete these checks.

If you receive an insufficient memory message —

l Save and close any open files and exit any open programs you are not using to see if that resolves the problem.

l See the software documentation for minimum memory requirements. If necessary, install additional memory.

l Reseat the memory modules to ensure that your computer is successfully communicating with the memory.

l Run the Dell Diagnostics (see Dell Diagnostics).

If you experience other memory problems —

l Reseat the memory modules to ensure that your computer is successfully communicating with the memory.

l Ensure that you are following the memory installation guidelines.

l Run the Dell Diagnostics (see Dell Diagnostics).

Mouse Problems

Check the mouse cable —

1. Check the cable connector for bent or broken pins and for damaged or frayed cables. Straighten bent pins. 2. Remove mouse extension cables, if used, and connect the mouse directly to the computer. 3. Shut down the computer, reconnect the mouse cable as shown in the Quick Reference Guide for your computer, and then restart the computer.

Restart the computer —

1. Simultaneously press to display the Start menu. 2. Type u , press the keyboard arrow keys to highlight Shut down or Turn Off , and then press . 3. After the computer turns off, reconnect the mouse cable as shown on the in the Quick Reference Guide for your computer. 4. Start the computer.

Test the mouse — Connect a properly working mouse to the computer, and try using the mouse. If the new mouse works, the original mouse is faulty.

Check the mouse settings —

1. Click the Start button, click Control Panel , and then click Printers and Other Hardware . 2. Click Mouse . 3. Try adjusting the settings.

If you are using a PS/2 mouse

Page 192 of the Dell Desktop Computer (DCCY) user manual — Power Problems
Page 192 · click to enlarge
Page 192
1. Enter system setup and ensure that the Mouse Port option is set to On . 2. Exit system setup and restart the computer.

Reinstall the mouse driver — See Reinstalling Drivers and Utilities.

Run the Dell Diagnostics —

l See Dell Diagnostics.

Check for software and hardware conflicts —

l See Resolving Software and Hardware Incompatibilities.

Network Problems

Fill out the Diagnostics Checklist as you complete these checks.

Check the network cable connector — Ensure that the network cable is firmly inserted into both the network connector on the back of the computer and the network jack.

Check the network lights on the front or back of the computer depending on system chassis type. — No connection speed light indicates that no network communication exists. Replace the network cable.

Restart the computer and log on to the network again

Check your network settings — Contact your network administrator or the person who set up your network to verify that your network settings are correct and that the network is functioning.

Check for software and hardware conflicts —

l See Resolving Software and Hardware Incompatibilities.

Power Problems

Fill out the Diagnostics Checklist as you complete these checks.

If the power light is green and the computer is not responding — See Diagnostic Lights

If the power light is blinking green — The computer is in standby mode. Press a key on the keyboard or move the mouse to resume normal operation.

If the power light is off — The computer is either turned off or is not receiving power.

l Reseat the power cable into both the power connector on the back of the computer and the electrical outlet.

l If the computer is plugged into a power strip, ensure that the power strip is plugged into an electrical outlet and that the power strip

is turned on. Also bypass power protection devices, power strips, and power extension cables to verify that the computer turns on

Page 193 of the Dell Desktop Computer (DCCY) user manual — Printer Problems
Page 193 · click to enlarge
Page 193

properly.

l Ensure that the electrical outlet is working by testing it with another device, such as a lamp.

l Ensure that the main power cable and front panel cable are securely connected to the system board.

If the power light is amber and green or steady amber — A device might be malfunctioning or incorrectly installed.

l Remove and then reinstall the memory modules (see Memory).

l Remove and then reinstall any cards.

l Remove and then reinstall the graphics card, if applicable.

If the power light is blinking amber —

The computer is receiving electrical power, but an internal power problem might exist.

l Ensure that the voltage selection switch is set to match the AC power at your location (if applicable).

l Ensure that the processor power cable is securely connected to the system board.

Eliminate interference — Some possible causes of interference are:

l Power, keyboard, and mouse extension cables

l Too many devices on a power strip

l Multiple power strips connected to the same electrical outlet

Printer Problems

Fill out the Diagnostics Checklist as you complete these checks.

Check the printer documentation — See the printer documentation for setup and troubleshooting information.

Ensure that the printer is turned on

Check the printer cable connections —

l See the printer documentation for cable connection information.

l Ensure that the printer cables are securely connected to the printer and the computer.

Test the electrical outlet —

Ensure that the electrical outlet is working by testing it with another device, such as a lamp. —

Verify that the printer is recognized by Windows —

1. Click the Start button, click Control Panel , and then click Printers and Other Hardware . 2. Click View installed printers or fax printers .

If the printer is listed, right-click the printer icon.

3. Click Properties and click the Ports tab. For a parallel printer, ensure that the Print to the following port(s): setting is LPT1 (Printer Port) . For a USB printer, ensure that the Print to the following port(s): setting is USB .

Reinstall the printer driver — See the printer documentation for instructions.

Page 194 of the Dell Desktop Computer (DCCY) user manual — No sound from speakers
Page 194 · click to enlarge
Page 194

Restoring Default Settings

To restore the computer's system settings to their default values —

1. Turn on or restart your computer. 2. When Press to Enter Setup appears in the upper-right corner of the screen, press immediately.

If you wait too long and the Microsoft® Windows® logo appears, continue to wait until you see the Windows desktop. Then shut down your computer through the Start menu and try again.

3. Under System Management , select the Maintenance option and follow the directions on the screen.

Serial or Parallel Device Problems

Fill out the Diagnostics Checklist as you complete these checks.

Check the option setting — See the device's documentation for the recommended settings. Then enter system setup (see System Setup) and ensure that the Serial Port #1 setting (or the Serial Port #2 settings if you have an optional serial port adapter installed) or the LPT Port Mode setting matches the recommended settings.

Run the Dell Diagnostics — See Dell Diagnostics.

Sound and Speaker Problems

Fill out the Diagnostics Checklist as you complete these checks.

No sound from speakers

Check the speaker cable connections — Ensure that the speakers are connected as shown on the setup diagram supplied with the speakers. If you purchased an audio card, ensure that the speakers are connected to the card.

Ensure that the subwoofer and the speakers are turned on — See the setup diagram supplied with the speakers. If your speakers have volume controls, adjust the volume, bass, or treble to eliminate distortion.

Adjust the Windows volume control — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted.

Disconnect headphones from the headphone connector — Sound from the speakers is automatically disabled when headphones are connected to the computer's front-panel headphone connector.

Test the electrical outlet — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.

Enable digital mode — Your speakers do not work if the CD drive is operating in analog mode.

1. Click the Start button, click Control Panel , and then click Sounds, Speech, and Audio Devices . 2. Click Sounds and Audio Devices .
Page 195 of the Dell Desktop Computer (DCCY) user manual — If the screen is blank
Page 195 · click to enlarge
Page 195
3. Click the Hardware tab. 4. Double-click the name of your CD drive. 5. Click the Properties tab 6. Check the Enable digital CD audio for this CD-ROM device box.

Eliminate possible interference — Turn off nearby fans, fluorescent lights, or halogen lamps to check for interference.

Run the speaker diagnostics

Reinstall the audio driver — See Drivers.

Check the device option setting — Enter system setup (see System Setup) and ensure that the Audio Controller option is set to On. Exit system setup and restart your computer.

Run the Dell Diagnostics — See Dell Diagnostics.

Check for software and hardware conflicts — See Resolving Software and Hardware Incompatibilities.

No sound from headphones

Check the headphone cable connection — Ensure that the headphone cable is securely inserted into the headphone connector.

Disable digital mode — Your headphones do not work if the CD drive is operating in digital mode.

1. Click the Start button, click Control Panel , and then click Sounds, Speech, and Audio Devices . 2. Click Sounds and Audio Devices . 3. Click the Hardware tab. 4. Double-click the name of your CD drive. 5. Click the Properties tab. 6. Uncheck the Enable digital CD audio for this CD-ROM device box.

Adjust the Windows volume control — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted.

Video and Monitor Problems

Fill out the Diagnostics Checklist as you complete these checks.

If the screen is blank

Check the monitor cable connection —

l If you purchased a graphics card, ensure that the monitor is connected to the card.

l Ensure that your monitor is properly connected (see the Quick Reference Guide that came with your computer).

l If you are using a video extension cable and removing the cable solves the problem, the cable is defective.

l Swap the computer and monitor power cables to determine if the power cable is defective.

l Check the connector for bent or broken pins. (It is normal for monitor cable connectors to have missing pins.)

Check the monitor power light — If the power light is off, firmly press the button to ensure that the monitor is turned on. If the power light is lit or blinking, the monitor has power. If the power light is blinking, press a key on the keyboard or move the mouse.

Page 196 of the Dell Desktop Computer (DCCY) user manual — If the screen is difficult to read
Page 196 · click to enlarge
Page 196

Test the electrical outlet — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.

Test the monitor — Connect a properly working monitor to the computer, and try using the monitor. If the new monitor works, the original monitor is faulty.

Check the diagnostic lights — See Diagnostic Lights.

Check the card setting — Enter system setup (see System Setup) and ensure that Primary Video option is set correctly. Exit system setup and restart your computer.

Run the monitor self-test — Check the monitor documentation for more information.

If the screen is difficult to read

Check the monitor settings — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing (degaussing) the monitor, and running the monitor self-test.

Move the subwoofer away from the monitor — If your speaker system includes a subwoofer, ensure that the subwoofer is at least 60 cm (2 ft) away from the monitor.

Move the monitor away from external power sources — Fans, fluorescent lights, halogen lamps, and other electrical devices can cause the screen image to appear "shaky." Turn off nearby devices to check for interference.

Adjust the Windows display settings —

1. Click the Start button, click Control Panel , and then click Appearance and Themes . 2. Click Display and click the Settings tab. 3. Try different settings for Screen resolution and Color quality.
Page 197 of the Dell Desktop Computer (DCCY) user manual — Desktop Computer
Page 197 · click to enlarge
Page 197

Chassis Intrusion Switch

Dell™ Optiplex™ 740 Systems User's Guide

Removing the Chassis Intrusion Switch

Replacing the Chassis Intrusion Switch

Resetting the Chassis Intrusion Detector

Removing the Chassis Intrusion Switch

1. Follow the procedures in Before You Begin . 2. If removing the chassis intrusion switch on a small form factor computer, remove the hard drive (see Drives ). 3. Disconnect the chassis intrusion switch cable from the system board (see System Board Components for mini tower computers or System Board Components for desktop computers or System Board Components for small form factor computers).
4. Slide the chassis intrusion switch out of its slot, and remove the switch and its attached cable from the computer.

Mini Tower Computer

Dell Desktop Computer (DCCY) — Mini Tower Computer diagram (page 197)
Fig. 174 · Mini Tower Computer

Desktop Computer

Page 198 of the Dell Desktop Computer (DCCY) user manual — Resetting the Chassis Intrusion Detector
Page 198 · click to enlarge
Page 198
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 198)
Fig. 175 · Removing a PCI Card From the Riser-Card Cage

Small Form Factor Computer

Dell Desktop Computer (DCCY) — Small Form Factor Computer diagram (page 198)
Fig. 176 · Small Form Factor Computer

Replacing the Chassis Intrusion Switch

1. Gently slide the chassis intrusion switch into its slot and reconnect the cable to the system board. 2. Replace the computer cover (see Replacing the Computer Cover ).

Resetting the Chassis Intrusion Detector

1. Turn on (or restart) your computer. 2. When the blue DELL™ logo appears, press immediately.

If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Then shut down your computer and try again.

3. Select the Chassis Intrusion option and then press the leftor right-arrow key to select Reset . Change the setting to On , On-Silent , or Disabled .
4. Press , press the leftand right-arrow keys to highlight Save/Exit, and then press to restart the computer and implement your changes.
Page 199 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 199 · click to enlarge
Page 199
Page 199 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 200 of the Dell Desktop Computer (DCCY) user manual — Desktop System Board Screws
Page 200 · click to enlarge
Page 200

Replacing the System Board

Dell™ Optiplex™ 740 Systems User's Guide

Removing the System Board: Mini Tower, Desktop, and Small Form Factor Computers

1. Follow the procedures in Before You Begin .
2. Remove any components that restrict access to the system board such as: the (optical drive(s), floppy drive, hard drive, and I/O panel (as applicable). 3. Remove the processor and heat sink assembly:
l Mini Towersee Processor
l Desktopsee Processor
l Small Form Factorsee Processor
4. Disconnect all cables from the system board. 5. Remove the screws from the system board.

l Mini Tower System Board Screws

l Desktop System Board Screws

l Small Form Factor System Board Screws

6. Slide the system board assembly toward the front of the computer, and then lift the board up and away.

Mini Tower System Board Screws

Dell Desktop Computer (DCCY) — Mini Tower System Board Screws diagram (page 200)
Fig. 177 · Mini Tower System Board Screws

1 mini tower system board 2 screws (8)

Desktop System Board Screws

Page 201 of the Dell Desktop Computer (DCCY) user manual — Replacing the System Board: Mini Tower, Desktop, and Small Form Factor Computers
Page 201 · click to enlarge
Page 201
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 201)
Fig. 178 · Removing a PCI Card From the Riser-Card Cage

1 desktop system board 2 screws (8)

Small Form Factor System Board Screws

Dell Desktop Computer (DCCY) — Small Form Factor System Board Screws diagram (page 201)
Fig. 179 · Small Form Factor System Board Screws

1 small form factor system board 2 screws (6)

Place the system board assembly that you just removed next to the replacement system board to ensure it is identical.

Replacing the System Board: Mini Tower, Desktop, and Small Form Factor Computers

1. Gently align the board into the chassis and slide it toward the back of the computer. 2. Using the screws, secure the system board to the chassis. 3. Replace any components and cables that you removed from the system board. 4. Reconnect all cables to their connectors at the back of the computer. 5. Replace the computer cover (see Replacing the Computer Cover ).
Page 202 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 202 · click to enlarge
Page 202
Page 202 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 203 of the Dell Desktop Computer (DCCY) user manual — Dell™ Optiplex™ 740 Systems User's Guide
Page 203 · click to enlarge
Page 203

Dell™ Optiplex™ 740 Systems User's Guide

Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, OptiPlex, Inspiron, Dimension, Latitude, Dell Precision, DellNet, TravelLite, Dell OpenManage, PowerVault, Axim, PowerEdge, PowerConnect, and PowerApp are trademarks of Dell Inc.; AMD, AMD Athlon, AMD Phenom, and combinations thereof, and Cool 'n' Quiet are trademarks of Advanced Micro Devices, Inc; Microsoft and Windows are registered trademarks of Microsoft Corporation; IBM is a registered trademark of International Business Machines Corporation; Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

March 2008 RP699 Rev. A03

Page 204 of the Dell Desktop Computer (DCCY) user manual — About Your Mini Tower Computer
Page 204 · click to enlarge
Page 204

Mini Tower Computer

Dell™ Optiplex™ 740 Systems User's Guide

About Your Mini Tower Computer

About Your Mini Tower Computer

Front View

Dell Desktop Computer (DCCY) — About Your Mini Tower Computer diagram (page 204)
Fig. 180 · About Your Mini Tower Computer

1 optical drive (optional)

Insert media (if supported) into this drive.

2 Flexbay drive Can contain an optional floppy drive or an optional media card reader.

3 USB 2.0 connectors (2)

Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see System Setup for more information on booting to a USB device).

It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

4 LAN indicator light

This light indicates that a local area network (LAN) connection is established.

Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see Diagnostic Lights.

6 power button Press this button to turn on the computer.

7 power light The power light illuminates and blinks or remains solid to indicate different operating modes:

l No light — The computer is turned off.

l Steady green — The computer is in a normal operating state.

l Blinking green — The computer is in a power-saving mode.

Inside Your Computer · 5 diagnostic lights

Page 205 of the Dell Desktop Computer (DCCY) user manual — Back-Panel Connectors
Page 205 · click to enlarge
Page 205
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 205)
Fig. 181 · Removing a PCI Card From the Riser-Card Cage

l Blinking or solid amber — See Power Problems.

To exit from a power-saving mode, press the power button or use the keyboard or the mouse if it is configured as a wake device in the Windows Device Manager. For more information about sleep modes and exiting from a power-saving mode, see Power Management.

See System Lights for a description of light codes that can help you troubleshoot problems with your computer.

This light flickers when the hard drive is being accessed.

Use the headphone connector to attach headphones and most kinds of speakers.

Back View

Dell Desktop Computer (DCCY) — Back View diagram (page 205)
Fig. 182 · Back View

1 cover release latch

This latch allows you to open the computer cover.

2 padlock ring Insert a padlock to lock the computer cover.

3 voltage selection switch

Your computer is equipped with a manual voltage-selection switch.

To help avoid damaging a computer with a manual voltage selection switch, set the switch for the voltage that most closely matches the AC power available in your location.

Also, ensure that your monitor and attached devices are electrically rated to operate with the AC power available in your location.

Insert the power cable.

Plug serial, USB, and other devices into the appropriate connectors. See Back-Panel Connectors.

6 card slots Access connectors for any installed PCI and PCI Express cards.

Back-Panel Connectors

4 power connector · 5 back-panel connectors

Page 206 of the Dell Desktop Computer (DCCY) user manual — Inside Your Computer
Page 206 · click to enlarge
Page 206
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 206)
Fig. 183 · Removing a PCI Card From the Riser-Card Cage

Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.

2 link integrity light

l Green — A good connection exists between a 10-Mbps network and

the computer.

l Orange — A good connection exists between a 100-Mbps network

and the computer.

l Yellow — A good connection exists between a 1-Gbps (or 1000-

Mbps) network and the computer.

l Off — The computer is not detecting a physical connection to the

network.

3 network adapter connector

To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached.

On computers with a network connector card, use the connector on the card.

It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.

4 network activity light

Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.

Use the green line-out connector to attach headphones and most speakers with integrated amplifiers.

On computers with a sound card, use the connector on the card.

Use the line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR.

On computers with a sound card, use the connector on the card.

7 USB 2.0 connectors (5)

Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

Plug the cable from your VGA-compatible monitor into the blue connector.

Connect a serial device, such as a handheld device, to the serial port. The default designations are COM1 for serial connector 1 and COM2 for serial connector 2.

For more information, see System Setup Options.

Inside Your Computer

Show 5 more labels / short text on this page
1 parallel connector · 5 line-out connector · 6 line-in connector · 8 video connector · 9 serial connector
Page 207 of the Dell Desktop Computer (DCCY) user manual — System Board Components
Page 207 · click to enlarge
Page 207
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 207)
Fig. 184 · Removing a PCI Card From the Riser-Card Cage

1 optical drive 2 floppy drive 3 power supply

4 chassis intrusion switch (optional) 5 system board 6 heat sink assembly

System Board Components

Dell Desktop Computer (DCCY) — System Board Components diagram (page 207)
Fig. 185 · System Board Components
Dell Desktop Computer (DCCY) — System Board Components diagram (page 207)
Fig. 186 · System Board Components

2 processor socket (CPU) 3 memory module connectors (DIMM_1, DIMM_2, DIMM_3, DIMM_4)

7 front-panel connector 8 power connector 9 intrusion switch connector

7 hard drive

Page 208 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 208 · click to enlarge
Page 208
Dell Desktop Computer (DCCY) — Removing a PCI Card From the Riser-Card Cage diagram (page 208)
Fig. 187 · Removing a PCI Card From the Riser-Card Cage
Page 209 of the Dell Desktop Computer (DCCY) user manual — Starting the Dell Diagnostics From the Drivers and Utilities Media (Optional)
Page 209 · click to enlarge
Page 209

Troubleshooting Tools and Utilities

Dell™ Optiplex™ 740 Systems User's Guide

Resolving Software and Hardware Incompatibilities

Dell Diagnostics

When to Use the Dell Diagnostics

If you experience a problem with your computer, perform the checks in this section and run the Dell Diagnostics before you contact Dell (see Contacting Dell) for technical assistance.

It is recommended that you print these procedures before you begin.

Enter system setup, review your computer's configuration information, and ensure that the device you want to test displays in system setup and is active (see Entering System Setup).

Start the Dell Diagnostics from either your hard drive or from the Drivers and Utilities media.

Starting the Dell Diagnostics From Your Hard Drive

The Dell Diagnostics is located on a hidden diagnostic utility partition on your hard drive.

1. Shut down the computer. Turn on (or restart) your computer. 2. When the DELL™ logo appears, press immediately.

If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Then shut down your computer and try again.

3. When the boot device list appears, highlight Boot to Utility Partition and press . 4. When the Dell Diagnostics Main Menu appears, select the test you want to run.

Starting the Dell Diagnostics From the Drivers and Utilities Media (Optional)

1. Insert the Drivers and Utilities media . 2. Shut down and restart the computer.

When the DELL™ logo appears, press immediately.

If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop. Then shut down your computer and try again.

Show 5 more labels / short text on this page
Dell Diagnostics · System Lights · Diagnostic Lights · Beep Codes · Error Messages
Page 210 of the Dell Desktop Computer (DCCY) user manual — System Lights
Page 210 · click to enlarge
Page 210

3. When the boot device list appears, highlight IDE CD-ROM Device and press . 4. Select the IDE CD-ROM Device option from the CD boot menu. 5. Select the Boot from CD-ROM option from the menu that appears. 6. Type 1 to start the Drivers and Utilities media menu. 7. Type 2 to start the Dell Diagnostics. 8. Select Run the 32 Bit Dell Diagnostics from the numbered list. If multiple versions are listed, select the version appropriate for your computer. 9. When the Dell Diagnostics Main Menu appears, select the test you want to run.

Dell Diagnostics Main Menu

1. After the Dell Diagnostics loads and the Main Menu screen appears, click the button for the option you want.
Dell Desktop Computer (DCCY) — Dell Diagnostics Main Menu diagram (page 210)
Fig. 188 · Dell Diagnostics Main Menu

Express Test Performs a quick test of devices. This test typically takes 10 to 20 minutes and requires no interaction on your part. Run Express Test first to

Performs a thorough check of devices. This test typically takes an hour or more and requires you to answer questions periodically.

Custom Test Tests a specific device. You can customize the tests you want to run.

Lists the most common symptoms encountered and allows you to select a test based on the symptom of the problem you are having.

2. If a problem is encountered during a test, a message appears with an error code and a description of the problem. Write down the error code and problem description and follow the instructions on the screen.

If you cannot resolve the error condition, contact Dell (see Contacting Dell).

3. If you run a test from the Custom Test or Symptom Tree option, click the applicable tab described in the following table for more information.

Results Displays the results of the test and any error conditions encountered.

Errors Displays error conditions encountered, error codes, and the problem description.

Help Describes the test and may indicate requirements for running the test.

Configuration Displays your hardware configuration for the selected device.

The Dell Diagnostics obtains configuration information for all devices from system setup, memory, and various internal tests, and it displays the information in the device list in the left pane of the screen. The device list may not display the names of all the components installed on your computer or all devices attached to your computer.

Parameters Allows you to customize the test by changing the test settings.

4. When the tests are completed, if you are running the Dell Diagnostics from the Drivers and Utilities media , remove the CD or DVD. 5. When the tests are complete, close Close the test screen to return to the Main Menu screen. To exit the Dell Diagnostics and restart the computer, close the Main Menu screen.

System Lights

Your power button light and hard-drive light may indicate a computer problem.

Dell Desktop Computer (DCCY) — System Lights diagram (page 210)
Fig. 189 · System Lights

Solid green Power is on, and the computer is operating normally. On the desktop computer, a solid green light indicates a network connection.

Tab · Function

Page 211 of the Dell Desktop Computer (DCCY) user manual — Diagnostic Lights
Page 211 · click to enlarge
Page 211

Blinking green The computer is in a power-saving mode (Microsoft® Windows® XP).

Press the power button, move the mouse, or press a key on the keyboard to wake the computer.

Blinks green several times and then turns off

A configuration error exists. Check the diagnostic lights to see if the specific problem is identified.

Solid yellow The Dell Diagnostics is running a test, or a device on the system board may be faulty or incorrectly installed.

If the Dell Diagnostics is running, allow the testing to complete.

If the computer does not boot, contact Dell for technical assistance.

Blinking yellow A power supply or system board failure has occurred. See Power Problems.

Solid green and a beep code during POST

A problem was detected while the BIOS was executing. See Beep Codes for instructions on diagnosing the beep code. Also, check the diagnostic lights to see if the specific problem is identified.

Solid green power light and no beep code and no video during POST

The monitor or the graphics card may be faulty or incorrectly installed.

Check the diagnostic lights to see if the specific problem is identified (see Video and Monitor Problems).

Solid green power light and no beep code but the computer locks up during POST

An integrated system board device may be faulty. Check the diagnostic lights to see if the specific problem is identified. If the problem is not identified, contact Dell for technical assistance.

Diagnostic Lights

To help you troubleshoot a problem, your computer has four lights labeled "1," "2," "3," and "4" on the front panel. The lights can be off or green. When the computer starts normally, the patterns or codes on the lights change as the boot process completes. If the POST portion of system boot completes successfully, all four lights display solid green. If the computer malfunctions during the POST process, the pattern displayed on the LEDs may help identify where in the process the computer halted.

The computer is in a normal off condition, or a possible pre-BIOS failure has occurred.

Plug the computer into a working electrical outlet and press the power button.

The diagnostic lights are not lit after the computer successfully boots to the operating system.

A possible BIOS failure has occurred; the computer is in the recovery mode.

Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer.

A possible processor failure has occurred. Reinstall the processor and restart the computer.

Memory modules are detected, but a memory failure has occurred.

l If you have one memory module installed, reinstall it and restart the computer (see

Memory for instructions on how to remove and install memory modules).

l If you have two or more memory modules installed, remove the modules, reinstall one

module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error.

l If available, install properly working memory of the same type into your computer.

l If the problem persists, contact Dell.

A possible graphics card failure has occurred.

l If the computer has a graphics card, remove the card, reinstall it, and then restart the

computer.

l If the problem still exists, install a graphics card that you know works and restart the

computer.

l If the problem persists or the computer has integrated graphics, contact Dell.

A possible floppy or hard drive failure has occurred.

Reseat all power and data cables and restart the computer.

A possible USB failure has occurred. Reinstall all USB devices, check cable connections, and then restart the computer.

No memory modules are detected. l If you have one memory module installed, reinstall it and restart the computer (see

Memory for instructions on how to remove and install memory modules).

l If you have two or more memory modules installed, remove the modules, reinstall one

module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error.

l If available, install properly working memory of the same type into your computer.

l If the problem persists, contact Dell.

Light Pattern · Problem Description · Suggested Resolution

Page 212 of the Dell Desktop Computer (DCCY) user manual — Error Messages
Page 212 · click to enlarge
Page 212

Memory modules are detected, but a memory configuration or compatibility error exists.

l Ensure that no special memory module/memory connector placement requirements

exist (see Memory).

l Verify that the memory modules that you are installing are compatible with your

computer.

l If the problem persists, contact Dell.

A failure has occurred.

l Ensure that the cables are properly connected to the system board from the hard

drive, and optical drive.

l Check the computer message that appears on your monitor screen.

This pattern also displays when you enter system setup and may not indicate a problem (see Entering System Setup).

l If the problem persists, contact Dell.

After POST is complete, all four diagnostic lights turn green briefly before turning off to indicate normal operating condition.

None.

Beep Codes

Your computer might emit a series of beeps during start-up if the monitor cannot display errors or problems. This series of beeps, called a beep code, identifies a problem. One possible beep code consists of one long beep and then two short beeps. This beep code tells you that the computer encountered a memory test failure.

If your computer beeps during start-up:

1. Write down the beep code on the Diagnostics Checklist (see Diagnostics Checklist ). 2. Run the Dell Diagnostics to identify a more serious cause (see Dell Diagnostics ). 3. Contact Dell for technical assistance (see Contacting Dell ).
Dell Desktop Computer (DCCY) — Beep Codes diagram (page 212)
Fig. 190 · Beep Codes

1 long, 2 short Memory test failure (bad memory during memory sizing)

Error Messages

Fill out the Diagnostics Checklist as you complete these checks (see Diagnostics Checklist).

If the message is not listed, see the documentation for the operating system or the program that was running when the message appeared.

A filename cannot contain any of the following characters: \ / : * ? " < > | — Do not use these characters in filenames.

A required .DLL file was not found — The program that you are trying to open is missing an essential file. To remove and then reinstall the program:

1. Click the Start button, click Control Panel , and then click Add or Remove Programs . 2. Select the program you want to remove. 3. Click the Change or Remove Program icon. 4. See the program documentation for installation instructions.

Alert! Previous attempts at booting this system have failed at checkpoint [nnnn]. For help in resolving this problem, please note this checkpoint and contact Dell Technical Support — Contact Dell (see Contacting Dell) and report the checkpoint code (nnnn) to the support technician.

Alert! Air temperature sensor not detected — For any computer type except the ultra small form factor computer, ensure that all cables are securely fastened to the I/O panel and to the system board and reboot your computer. If this does not resolve the problem or if you have an ultra small form factor computer, contact Dell (see Contacting Dell).

Attachment failed to respond — See Drive Problems.

Page 213 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 213 · click to enlarge
Page 213

Bad command or file name — Ensure that you spelled the command correctly, put spaces in the proper place, and used the correct pathname.

Bad error-correction code (ECC) on disk read — See Drive Problems.

Controller has failed — See Drive Problems.

Data error — See Drive Problems.

Decreasing available memory —

See Lockups and Software Problems.

Diskette drive 0 seek failure — See Drive Problems.

Diskette read failure —

See Drive Problems.

Diskette subsystem reset failed — Run the Dell Diagnostics (see Dell Diagnostics).

Diskette write protected — Slide the write-protect notch on the floppy disk to the open position.

Drive not ready — Put a floppy disk in the drive.

Gate A20 failure —

See Lockups and Software Problems.

Hard-disk configuration error —

Hard-disk controller failure —

Hard-disk drive failure —

Hard-disk drive failure —

See Drive Problems.

Insert bootable media — Insert a bootable floppy disk or CD.

Invalid configuration information - please run SETUP program — Enter system setup and correct the computer configuration information (see Entering System Setup).

Keyboard failure — See Keyboard Problems.

Memory address line failure at address, read value expecting value — See Lockups and Software Problems.

Memory allocation error —

1. Turn off the computer, wait 30 seconds, and then restart the computer. 2. Try to run the program again. 3. If the error message appears again, see the software documentation for additional troubleshooting suggestions.
Page 214 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 214 · click to enlarge
Page 214

Memory data line failure at address, read value expecting value —

Memory double word logic failure at address, read value expecting value —

Memory odd/even logic failure at address, read value expecting value —

Memory write/read failure at address, read value expecting value —

Memory size in CMOS invalid —

See Lockups and Software Problems.

No boot device available —

l If the floppy drive is your boot device, ensure that a bootable floppy disk is in the drive.

l If the hard drive is your boot device, ensure that the cables are connected and that the drive is installed properly and partitioned as a

boot device.

l Enter system setup and ensure that the boot sequence information is correct (see Entering System Setup).

No boot sector on hard-disk drive — Enter system setup and ensure that the computer configuration information for the hard drive is correct (see Entering System Setup).

No timer tick interrupt — Run the Dell Diagnostics (see Dell Diagnostics).

Non-system disk or disk error — Replace the floppy disk with one that has a bootable operating system or remove the floppy disk from drive A and restart the computer.

Not a boot diskette — Insert a bootable floppy disk and restart your computer.

Not enough memory or resources. Close some programs and try again — Close all windows and open the program that you want to use. In some cases, you might have to restart your computer to restore computer resources. If so, run the program that you want to use first.

Operating system not found — Contact Dell (see Contacting Dell).

Plug and Play Configuration Error —

1. Turn your computer off, unplug it from the electrical outlet, and then remove all but one of the cards. 2. Plug in your computer and reboot it. 3. If the message reappears, the installed card might be malfunctioning. If the message does not reappear, turn off the computer and reinsert one of the other cards. 4. Repeat this process until you identify which card is malfunctioning.

Requested sector not found —

See Drive Problems.

Sector not found —

l Run the Windows error-checking utility to check the file structure on the floppy disk or hard drive. See Windows Help for instructions.

l If a large number of sectors are defective, back up the data (if possible), and then reformat the floppy disk or hard drive.

Seek error — See Drive Problems.

Read fault — · Reset failed —

Page 215 of the Dell Desktop Computer (DCCY) user manual — Microsoft ® Windows ® XP
Page 215 · click to enlarge
Page 215

Shutdown failure — Run the Dell Diagnostics (see Dell Diagnostics).

Time-of-day clock stopped —

Time-of-day not set-please run the System Setup program —

Enter system setup (see Entering System Setup) and correct the date or time. If the problem persists, replace the battery (see Replacing the Battery).

Timer chip counter 2 failed — Run the Dell Diagnostics (see Dell Diagnostics).

Unexpected interrupt in protected mode — Run the Dell Diagnostics (see Dell Diagnostics).

If no replacement drive is immediately available and the drive is not the only bootable drive, enter system setup (see Entering System Setup) and change the appropriate drive setting to None. Then remove the drive from the computer.

Write fault on selected drive —

See Drive Problems.

<drive letter>:\ is not accessible. The device is not ready — The selected drive cannot read its medium. Depending on its medium type, insert a floppy, CD, DVD, or Zip disk into the drive and try again.

Resolving Software and Hardware Incompatibilities

If a device is either not detected during the operating system setup or is detected but incorrectly configured, you can use Device Manager or the Hardware Troubleshooter to resolve the incompatibility.

Microsoft ® Windows ® XP

To resolve incompatibilities using Device Manager:

1. Click the Start button and click Control Panel . 2. Click Performance and Maintenance and click System . 3. Click the Hardware tab and click Device Manager . 4. In the Device Manager list, check for devices that are incorrectly configured.

Incorrectly configured devices are indicated by a yellow exclamation point [!] or a red X if the device has been disabled.

5. Double-click any device marked with an exclamation point to display the Properties window.

The Device status area in the Properties window reports the devices that need to be re-configured.

6. Reconfigure the devices or remove the devices from the Device Manager . See the documentation that came with the device for information on configuring the device.

To resolve incompatibilities using the Windows XP Hardware Troubleshooter:

1. Click the Start button and click Help and Support . 2. Type hardware troubleshooter in the Search field and click the arrow to start the search.

Write fault —

Page 216 of the Dell Desktop Computer (DCCY) user manual — Removing a PCI Card From the Riser-Card Cage
Page 216 · click to enlarge
Page 216
3. Click Hardware Troubleshooter in the Search Results list. 4. In the Hardware Troubleshooter list, click I need to resolve a hardware conflict on my computer , and click Next .
Page 217 of the Dell Desktop Computer (DCCY) user manual — Dell™ Optiplex™ 740 Systems User's Guide
Page 217 · click to enlarge
Page 217

Warranty

Dell™ Optiplex™ 740 Systems User's Guide

Dell Inc. ("Dell") manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry-standard practices. For information about the Dell warranty for your computer, see the Product Information Guide or separate paper warranty document that shipped with your computer.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Display codes

Error codes

What the fault codes shown on the display mean and how to clear them.

CodeMeaningFix
1 shortF12 key pressed p.212
Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
The computer is in a normal off condition, or a possible pre-BIOS failure has occurred. The diagnostic lights are not lit after the computer successfully boots to the operating system.Plug the computer into a working electrical outlet and press the power button. p.211
A possible BIOS failure has occurred; the computer is in the recovery mode.Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer. p.211
A possible processor failure has occurred.Reinstall the processor and restart the computer. p.211
Memory modules are detected, but a memory failure has occurred.l If you have one memory module installed, reinstall it and restart the computer (see Memory for instructions on how to remove and install memory modules). l If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error. l If available, install properly working memory of the same type into your computer. l If the problem persists, contact Dell. p.211
A possible graphics card failure has occurred.l If the computer has a graphics card, remove the card, reinstall it, and then restart the computer. l If the problem still exists, install a graphics card that you know works and restart the computer. l If the problem persists or the computer has integrated graphics, contact Dell. p.211
A possible floppy or hard drive failure has occurred.Reseat all power and data cables and restart the computer. p.211
A possible USB failure has occurred.Reinstall all USB devices, check cable connections, and then restart the computer. p.211

Ask about the Dell Desktop Computer (DCCY)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Dell Desktop Computer (DCCY)

Be the first to ask — other owners or our team will answer.

Original document

Dell Desktop Computer (DCCY) manual PDF

217 pages·6.7 MB·Fan·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…