Instruction/ maintenance manual of the product ER30D-C Dacor
Go to page of 24
I n s t a l l a t i o n I n s t r u c t i o n s E p i c u r e ® R a n g e For Use with Models: ER30D, ER30D-C, ER30DSR Part No. 102187 Rev . C THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LA TEST EDITION OF ANSI Z21.1 ST ANDARD FOR HOUSEHOLD GAS APPLIANCES.
© 2007 Dacor , all rights reserved. All specifications subject to change without notice. Dacor assumes no liability for changes to specifications..
1 Important Safety Instructions .................................................. 1-3 Customer Service Information .................................................... 3 Planning the Installation ......................................................
2 Impor tant Safety Instructions W ARNING Read the accompanying use and care manual before operating this appliance. Keep packaging materials away from children. Plastic sheets and bags can cause suffocation. If you receive a damaged product, immediately contact your dealer or builder .
3 Model and Serial Number Location Serial number and rating labels located inside unit, behind grill. If the unit requires service or you have questions or problems with installation, contact your Dacor dealer or the Dacor Customer Service T eam. Dacor Customer Service T eam 1-800-793-0093 (U.
4 Planning the Installation W ARNING IMPORT ANT : Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Electrical Requirements IMPORT ANT : The information below applies only to free standing units equipped for use in the U.
5 Product Dimensions All tolerances: +1/16”, -0 (+1.6 mm, -0) Planning the Installation B E A C D Gas Inlet Electrical connection hole in bottom Back of Range Range electrical access, cover removed .
6 Planning the Installation 37 7/8” (962mm) to 35 3/4” (908mm) Rear of Front Panel to Back of Chassis 28 1/8” (714mm) 45 9/16” (1 157mm) 26 5/8” (676mm) 25 5/8” (651mm) 23 9/16” (598mm) .
7 Planning the Installation Cutout DIMENSIONS F G 36” (914 mm)* 30” (762 mm)** 30 1 / 1 6 ” (916 mm)* * Recommended ** Minimum 24” Typ . (610mm) 25” Typ . (635mm) F G Cabinet Cutout Dimensions Cabinet Layout Carefully check the location where the range is to be installed.
8 Parts List 2 Grates 1 Small Stack Burner Cap 1 Small Stack Burner Ring 2 Large Stack Burner Caps 2 Large Stack Burner Rings 1 Crown Burner Cap 1 Crown Burner Ring 1 Crown Burner Head 1 GlideRack™ .
9 Installation Instructions Changing the Backguard (Models ER30D and ER30D-C) Models ER30D and ER30D-C come standard with a 3” backguard installed. The 6” and 9” backguards are optional. T o change the backguard: Remove and retain the three (3) chrome screws on the front of the existing backguard.
10 Close the door . Remove and retain the two screws from the back of the kick panel as shown below . Pull the kick panel free from the front of the unit. Remove the left end cap retaining screw from under the rim of the control panel and remove the end cap.
1 1 Locate the center mounting hole. Remove and retain the screw attached to the chassis beneath it. Insert the tabs on the trim piece into the slots on the range. Use the hex head screw (83023) removed from the side, a T orx head screw removed from the kick panel and the hex screws from the kit to attach the side panel to the range.
12 Installation Instructions Installation Instructions Removing the Oven Door W ARNING Do not attempt to disengage the hinge catches with the door removed from the oven. The hinge springs could release causing personal injury . Do not lift or carry the oven door by the door handle.
13 Installation Instructions Installation Instructions Connecting the Wiring to the Range Refer to the range rating label (see page 3) for power requirements.
14 Electrical Connection (cont.) Connecting the Conduit to the House Electrical Junction Box W ARNING Do not ground the appliance to a gas supply pipe or hot water pipe.
15 Installation Instructions Connection to power supply Connection to appliance (Page 13) Separate No. 10 (minimum copper grounding wire Junction Box Fasten clamp tightly on pipe Wire Nut, 4 Places 4 Wire Connection Conduit Junction Box Connection with External Ground Clamps Metal W ater Pipe No.
16 Installation Instructions Slide the end of the appliance cord into the strain relief from the bottom of the box Connect the white (neutral) wire to the neutral terminal in the box. Connect the L1 wire to the L1 power supply terminal in the box. Connect the L2 wire to the L2 power supply terminal in the box.
17 Installation Instructions Loop and Spade T erminal Connections Bare Wire Connections L1 Wire 4 Wire Appliance Cord Connection Strain Relief L2 Wire White Wire Green Wire Neutral T erminal L1 T ermi.
18 Installation Instructions Notch on bottom of hinge Lower lip of hinge receptacle Door Installation Final Installation Peel the protective plastic coating off of the range, including the range door . Adjust the range legs to the desired height. Carefully slide the range into position in the cutout.
19 Installation Instructions Stack Burner Installation Burner Head Crown Burner Stack Burner Spill T ray Burner Ring Ridge on bottom of burner cap STEP 1: Put burner ring on top of head. STEP 2: Turn ring until it drops into place. T wist back and forth to assure proper seating.
20 Installation Instructions Installation Checklist W ARNING T o ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. Proper installation is the responsibility of the homeowner .
.
Dacor ● 1440 Bridge Gate Drive, Diamond Bar , CA 91765 ● T el: (800) 793-0093 ● F AX: (626) 403-3130 ● www .Dacor .com.
An important point after buying a device Dacor ER30D-C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dacor ER30D-C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dacor ER30D-C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dacor ER30D-C you will learn all the available features of the product, as well as information on its operation. The information that you get Dacor ER30D-C will certainly help you make a decision on the purchase.
If you already are a holder of Dacor ER30D-C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dacor ER30D-C.
However, one of the most important roles played by the user manual is to help in solving problems with Dacor ER30D-C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dacor ER30D-C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
