Instruction/ maintenance manual of the product OL-1911-05 Cisco Systems
Go to page of 30
CHAPTER 24-1 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 24 Configuring ATM Router Module Interfaces This chapter describes steps required to conf igure the A TM router modul.
24-2 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Overview of the ATM Router Module Overview of the ATM Router Module The A TM router module allows you to inte grate Layer 3 routing and A TM switching within a single chassis.
24-3 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Overview of the ATM Router Module Figur e 24-2 A TM Router Module T raf .
24-4 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Overview of the ATM Router Module • IP fragmentation support. • IP 6-path load balancing support. • Supports O AM-based PVC management.
24-5 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Hardware and Software Restrictions of the ATM Router Module Catalyst 8510.
24-6 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Hardware and Software Restrictions of the ATM Router Module Catalyst 8540.
24-7 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Hardware and Software Restrictions of the ATM Router Module Catalyst 8540.
24-8 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Hardware and Software Restrictions of the ATM Router Module Catalyst 8540.
24-9 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring ATM Router Module Interfaces • IP fragmentation. • IP 6-path load balancing. Note The A TM router module is only supported on A TM switches which ha ve a multiservice A TM switch processor installed.
24-10 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring ATM Router Module Interfaces Default ATM Router Module Inter.
24-11 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring LECs on ATM Router Module Interfaces (Catalyst 8540 MSR) Con.
24-12 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring LECs on ATM Router Module Interfaces (Catalyst 8540 MSR) Exa.
24-13 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring LECs on ATM Router Module Interfaces (Catalyst 8540 MSR) Router 1 ATM Interface Router1# configure terminal Router1(config)# interface atm 2/0 Router1(config-if)# ip address 1.
24-14 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring LECs on ATM Router Module Interfaces (Catalyst 8540 MSR) Router 1 ATM Interface Router1# configure terminal Router1(config)# interface atm 2/0 Router1(config-if)# ip address 1.
24-15 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring LECs on ATM Router Module Interfaces (Catalyst 8540 MSR) LAN.
24-16 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Multiprotocol Encapsulation over ATM Router 2 Ethernet Inter.
24-17 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Multiprotocol Encapsulation over ATM Note T raff ic shaping and policing are not supported on the A TM router module interfaces; for traff ic shaping and policing on A TM connections, use VP tunnels.
24-18 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Multiprotocol Encapsulation over ATM Multiprotocol Encapsula.
24-19 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Classical IP over ATM in a PVC Environment Ethernet Router RouterB# configure terminal RouterB(config)# ipx routing RouterB(config)# interface fastethernet 2/0 RouterB(config-if)# ip address 20.
24-20 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Classical IP over ATM in an SVC Environment For a detailed description of the role and operation of the A TM ARP server , refer to the Guide to ATM T echnology.
24-21 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Classical IP over ATM in an SVC Environment NSAP Address Example Figure 24-7 shows three A TM switch routers and a router connected using classical IP over A TM.
24-22 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Classical IP over ATM in an SVC Environment Configuring as a.
24-23 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Classical IP over ATM in an SVC Environment Displaying the I.
24-24 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Bridging Configuring Bridging All PVCs conf igured on A TM router module interfaces are used for bridging.
24-25 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Bridging Switch(config)# interface atm 3/0/0 Switch(config-i.
24-26 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring Bridging Example In the following e xample only PVC 2, 200 i.
24-27 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces Configuring IP Multicast Configuring IP Multicast T o conf igure IP mult.
24-28 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces About Rate Limiting Rate limiting can be applied to indi vidual interfaces.
24-29 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces About Rate Limiting Example The following is an e xample of how to conf igure rate limiting on your switch router: Router# configure terminal Enter configuration commands, one per line.
24-30 ATM and Layer 3 Switch Router Software Configuration Guide OL-1911-05 Chapter 24 Configuring ATM Router Module Interfaces About Rate Limiting.
An important point after buying a device Cisco Systems OL-1911-05 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems OL-1911-05 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems OL-1911-05 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems OL-1911-05 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems OL-1911-05 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems OL-1911-05, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems OL-1911-05.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems OL-1911-05. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems OL-1911-05 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
