Instruction/ maintenance manual of the product Engine 611 Cisco Systems
Go to page of 14
Corporate Headquarters: © 20 05 Cisco Syst ems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Installing Hard Disk Drives in the Cisco Wide Area Ap.
2 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Safety Overview Protecting Against Electrostatic Discharge Static electricit y can harm delicate componen ts insi de the de vice.
3 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Introduction Introduction The W AE-611 supports two 1-inch (2 .54-cm) slim 3.5-inch (8.89-cm) lo w voltage dif ferential (L VD) hard disk dri ves. The W AE-611 requires SCSI hard disk dri ves.
4 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Removing the Bezel and Cover Removing the Bezel and Cover War ni ng Before working on a sy stem that has an on/off switch, turn OFF the po wer and unplug the power cord.
5 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing the Beze l and Cover Figur e 2 Removing the Co v er Step 5 Slide the cov er back. Lift it up and of f the device. Caution For proper cool ing and airflo w , replace the cover before tu rning on the de vice.
6 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Assigning SCSI IDs Figur e 3 Location of Dr ive Ba ys Behind the Bez el Assigning SCSI IDs When you install or replace one or more of the SCSI disk dri v es in a W AE-611, you must assign a SCSI ID to each disk dri ve.
7 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing and Repl acing a SCS I Hard Disk Dri ve Figure 4 Hard Disk Dr ive Connec tors and SCSI ID Jumper Pins Step 2 T o check whether the configuration is correct, refer to the b oot time messages on th e de vice consol e.
8 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Removing and Replac ing a SCSI Hard Disk Drive Step 3 Po wer do wn the de vice and peripheral de vices, and disconnect the po w er cord and all external cables. Step 4 Press the release tabs on the bezel, and pull the bezel a way from the chassis.
9 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Replacing the Cover and B ezel and Completin g the Installation Step 11 Connect the power and SCSI cables to the dri ve. If you disconnected the IDE cable to the CD-R OM, reconnect it.
10 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Documentation T o complete your instal lation, follo w these steps: Step 1 Install the cov er . Place it into position, slide it forw ard, and then tighten the ca ptiv e screw (l abeled 1 in Figure 2 ).
11 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce If you prefer to see advisories an d notices as they are updated in real time, you can acces s a Product Security Incident Response T eam Really Simple Syndication (PSIR T RSS) feed from this URL: http://www .
12 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance Access to all tools on the Ci sco T echnical Support & Documentat ion website requires a Ci sco.
13 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce Definitions of Service Request Severity T o ensure that all s ervice reque sts are rep orted in a standard format, Cisco has established se verity definitions.
14 Installing Hard Disk Drives in the Cisco Wide Ar ea Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance This document is to be used in co njunction with th e documents listed i n the “Related Documentation” section. © 2006 Cisc o Systems, Inc.
An important point after buying a device Cisco Systems Engine 611 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems Engine 611 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems Engine 611 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems Engine 611 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems Engine 611 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems Engine 611, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems Engine 611.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems Engine 611. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems Engine 611 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
