Instruction/ maintenance manual of the product Network Device 7010 Cisco
Go to page of 22
1 Doc. No . Copyright © 1995 Cisco Systems, Inc. All rights reser ved. Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions 78-1230-02 Cisco 7010 Product Number s: CHAS-7010-DC=, CHAS-7010-A C.
2 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Product Overview Pr oduct Overview The Cisco 7010 is the five-slot model in the Cisco 7000 series. The Cisco 7010 provides three interface processor slots. Figure 1 shows the interf ace processor end of the Cisco 7010.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 3 Product Overview The remov able chassis cov er panel at the noninterface processor end of the router pro vides access to the internal components.
4 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Prerequisites Prerequisites Before you begin this installation, re vie w the safety guidelines in this section to av oid injuring yourself or damaging the equipment. This section also provides a list of the tools that you need to perform this replacement.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 5 Prerequisites Lifting Saf ely A fully configured chassis weighs approximately 70 pounds. Before installing the new (replacement) chassis, .
6 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Prerequisites Cable Str ain Relief If possible, position the new replacement chassis close enough to the e xisting system so that you can av oid ha ving to disconnect power and interf ace cables.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 7 Prerequisites Note If these conditions are not true, for instance, if you must remov e a rack-mounted chassis before you can install the new chassis, you must disconnect all po wer and netw ork interface cables.
8 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis T ools and P ar ts Required This section lists the tools and parts you will need to complete these replacement procedures.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 9 Replacing the Chassis Replacing a Rack-Mounted Chassis This section describes how to replace a chassis that is installed in an equipment rack.
10 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Removing the Existing Chassis from the Rac k Before removing the e xisting chassis from the rack, you must shut down the system po wer and disconnect the power cord and all interf ace cables.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 11 Replacing the Chassis Step 5 Repeat Steps 2 through 4 for the left ear . The strip of mounting holes on the front of each ear should be approximately flush with the end of the chassis. (See Figure 5.
12 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Figure 6 Installing the Chassis in a Standard Four -P ost, 19-Inch Equipment Rac k Installing the Cable Management .
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 13 Replacing the Chassis Figure 7 Cable Management Brac kets—Cisco 7010 Shown Follo w these steps to install the two cable management brack ets on the new chassis: Step 1 If you hav e ne w brackets to install on the ne w chassis, proceed to Step 4.
14 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Moving Processor Modules At the interface processor end of the chassis, slots contain the processor modules.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 15 Replacing the Chassis Figure 8 Ejector Lever s and Captive Installation Screws Interface processor card slot Interface processor card carr.
16 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Follo w these steps to mov e the processor modules to the ne w chassis: Step 1 Before moving an y processor modules.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 17 Replacing the Chassis Step 9 Using the thumb and forefinger of each hand to pinch each ejector , simultaneously push both ejectors inward (to ward the carrier handle) until the y snap into place and are at a full 90-degree orientation to the faceplate.
18 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Checking the Installation T o complete the replacement procedure, perform the follo wing steps to verify that the system is functioning properly . These steps will also help you verify that all the processor modules you mov ed are returned to their previous state.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 19 Replacing the Chassis Step 6 When the system boot is complete, the RP or RSP1 begins to initialize the interface processors. During this initialization, the LEDs on each interface processor beha ve dif ferently (most flash on and off).
20 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis show Command Descriptions and Examples This section describes the various show commands that you can use to display system status and configuration.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 21 Replacing the Chassis The command show interfaces serial slot/port displays statistics for the specific serial interface you specify by its slot/port address.
22 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Cisco Information Online Cisco Inf ormation Online Cisco Information Online (CIO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CIO to obtain additional content and services.
An important point after buying a device Cisco Network Device Cisco 7010 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Network Device Cisco 7010 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Network Device Cisco 7010 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Network Device Cisco 7010 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Network Device Cisco 7010 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Network Device Cisco 7010, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Network Device Cisco 7010.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Network Device Cisco 7010. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Network Device Cisco 7010 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
