Instruction/ maintenance manual of the product Engine 611 Cisco
Go to page of 16
Corporate Headquarters: © 20 05 Cisco Syst ems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Installing Hard Disk Drives in the Cisco Wide Area Ap.
2 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Safety Overview Protecting Against Electrostatic Discharge Static electricit y can harm delicate componen ts insi de the de vice.
3 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Introduction Introduction The W AE-611 supports two 1-inch (2 .54-cm) slim 3.5-inch (8.89-cm) lo w voltage dif ferential (L VD) hard disk dri ves. The W AE-611 requires SCSI h ard disk dri ves.
4 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Removing the Bezel and Cover Removing the Bezel and Cover War ni ng Before working on a sy stem that has an on/off switch, tu rn OFF the power and unplug the power cord.
5 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing the Beze l and Cover Figur e 2 Removing the Co ver Step 5 Slide the cov er back. Lift it up and of f the device. Caution For proper cool ing and airflo w , replace the cov er before turning on the de vice.
6 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Assigning SCSI IDs Figur e 3 Location of Dr ive Ba ys Behind the Bezel Assigning SCSI IDs When you install or replace one or more of the SCSI disk dri ves in a W AE-611, you must assign a SCSI ID to each disk dri ve.
7 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing and Repl acing a SCS I Hard Disk Dri ve • Seagate disks hav e two sets of jumpers.
8 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Removing and Replac ing a SCSI Hard Disk Drive Note All hard disk dri ves that you use in the W AE should ha ve the same throughput speed rating.
9 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Removing and Repl acing a SCS I Hard Disk Dri ve Figure 5 Disk Dr ive Or ienta t ion During Installation Step 11 Connect the power and SCSI cables to the dri ve. If you disconnected the IDE cable to the CD-R OM, reconnect it.
10 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Replacing the Cover a nd Beze l and Completing the Installation Replacing the Cover and Bezel and Completing the Installation War ni ng This unit is intend ed for installation in restricted acc ess areas.
11 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Documentation Step 4 Connect all external cables and the po wer cord to the device, and then pl ug the po wer cord into a properly grounded electrical out let.
12 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance In an emer gency , you can also reach PSIR T by telephone: • 1 877 228-73.
13 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce Submitting a Service Request Using the online T A C Se rvice Request T ool is the fast e st way to open S3 and S4 service requests.
14 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance Definitions of Service Request Severity T o ensure that a ll service req uests are r eported in a standard format, Cisco has established se verity definitions.
15 Installing Hard Disk Drives in th e Cisco Wide Area Application Engine 611 78-17404-01 Obtaining Technical Assista nce This document is to be used in con junction with th e documents listed i n the “Related Documentation” section. © 2006 Cisc o Systems, Inc.
16 Installin g Hard Disk D rives in th e Cisco Wide Area Ap plication Engine 611 78-17404-01 Obtaining Technica l Assistance.
An important point after buying a device Cisco Engine 611 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Engine 611 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Engine 611 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Engine 611 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Engine 611 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Engine 611, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Engine 611.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Engine 611. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Engine 611 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
