Instruction/ maintenance manual of the product CX-TRIP2 Cisco
Go to page of 28
1 Customer Order Number: Copyright © 1995 Cisco Systems, Inc. All rights reser ved. Documentation P ar t Number: T ok en Ring Interf ace Processor (TRIP) Installation and Configuration Product Numbe.
2 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description Pr oduct Description This section contains a detailed description of the T oken Ring interface processor (TRIP). The TRIP , shown in Figure 1, provides tw o or four T oken Ring ports for interconnection with IEEE 802.
Token Ring Interface Processor (TRIP) Installation and Configuration 3 Product Description When a T oken Ring interface is configured by using software commands, three LEDs for each port indicate the follo wing: • 16 Mbps—Lights if the interface is operating at 16 Mbps.
4 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description Figure 3 T oken Ring T ype 3 Lobe Cable Connectors, DB-9 and RJ-11 T ypes T oken Ring Ph ysical Connections The term T oken Ring refers to both IBM’ s T oken Ring Network, which IBM de veloped in the 1970s, and to IEEE 802.
Token Ring Interface Processor (TRIP) Installation and Configuration 5 Product Description In the typical T oken Ring network sho wn in Figure 4, lobe cables connect each T oken Ring station (TRIP port) to the MSA U (or MA U), and patch cables connect adjacent MSA Us (or MA Us) to form one large ring.
6 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description What is the Cisco 7000 Series? Network interfaces reside on modular interf ace processors, which provide .
Token Ring Interface Processor (TRIP) Installation and Configuration 7 Product Description Figure 6 Cisco 7010, Interface Processor End H2359 RP slot SP or SSP slot Interface processor slot 1 DC OK LE.
8 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description What is the Cisco 7500 Series? The Cisco 7500 series consists of three router models: the Cisco 7505, the Cisco 7507, and the Cisco 7513. All three models provide high reliability , av ailability , serviceability , and performance.
Token Ring Interface Processor (TRIP) Installation and Configuration 9 Product Description Figure 8 shows the rear of the se ven-slot Cisco 7507 router . In the Cisco 7507, up to two slots (2 and 3) are reserved for the Route Switch Processor (RSP2), which contains the system processor and performs packet switching functions.
10 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Product Description Figure 9 sho ws the rear of the Cisco 7513, with two A C-input power supplies installed.
Token Ring Interface Processor (TRIP) Installation and Configuration 11 Installation Prerequisites Installation Prerequisites This section provides a list of parts and tools you will need to perform the installation, and safety and ESD-pre vention guidelines to help you to a void injury and damage to the equipment.
12 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Installation Prerequisites T elephone Wir ing Saf ety Use the following guidelines when w orking with any equipment that is connected to telephone wiring or to other network cabling: • Ne ver install telephone wiring during a lightning storm.
Token Ring Interface Processor (TRIP) Installation and Configuration 13 Installation Prerequisites Online Inser tion and Remov al—An Ov er vie w Online insertion and remov al (OIR) allo ws you to remov e and replace interface processors while the system is operating; you do not need to notify the software or shut do wn the system po wer .
14 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Installation Prerequisites The function of the ejector lev ers (see Figure 10) is to align and seat the card connectors in the backplane.
Token Ring Interface Processor (TRIP) Installation and Configuration 15 Installation Prerequisites Figure 10 Ejector Lever s and Captive Installation Screws Interface processor card slot Interface pro.
16 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Installation List of P ar ts and T ools V erify that you ha ve all of the parts and optional equipment you will need to install the TRIP . If you need additional equipment, contact a service representativ e for ordering information.
Token Ring Interface Processor (TRIP) Installation and Configuration 17 Installation Step 4 Store the interface processor filler for future use. T o help prevent dust and contaminants from entering the chassis, do not lea v e the interface processor slot open.
18 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Installation Step 5 Place the remov ed TRIP on an antistatic mat or foam pad, or place it in an antistatic bag if you will return it to the factory .
Token Ring Interface Processor (TRIP) Installation and Configuration 19 Checking the Installation Step 7 Attach network interface cables or other connection equipment to the interf ace ports.
20 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Configuring the Interfaces Figure 13 TRIP LEDs Configuring the Interfaces Y ou can modify the startup configuration for Cisco 7000 series and Cisco 7500 series routers through the software command interpreter called EXEC .
Token Ring Interface Processor (TRIP) Installation and Configuration 21 Configuring the Interfaces T o configure T oken Ring interfaces using the setup EXEC command f acility , follow the instructions in the section “Using the Setup Command” on page 21.
22 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Configuring the Interfaces Step 3 Proceed through the remainder of the global parameter prompts, using the Return key to accept the defaults.
Token Ring Interface Processor (TRIP) Installation and Configuration 23 Configuring the Interfaces Basic Configuration Guidelines Follo wing are instructions for a basic configuration: enabling an interface and specifying IP routing.
24 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Checking the Configuration Chec king the Configuration After configuring the ne w interface(s) using either the setup command or the configure command, use the EXEC show commands to display status information.
Token Ring Interface Processor (TRIP) Installation and Configuration 25 Upgrading Microcode Upgrading Micr ocode Depending on how it is configured, the Cisco 7000 series router allo ws the Switch Pro.
26 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Upgrading Microcode Step 5 Confirm that you want the file copied into Flash: Copy trip1-0 from 131.108.13.111 into flash memory? [confirm] yes Step 6 If you do not want the other microcode files in Flash memory erased, enter no OR If you want Flash erased, enter ye s .
Token Ring Interface Processor (TRIP) Installation and Configuration 27 Upgrading Microcode Step 13 V erify that the correct microcode v ersion is av ailable in Flash memory: Router# show controllers .
28 T ok en Ring Interface Processor (TRIP) Installation and Configur ation Cisco Information Online Cisco Inf ormation Online Cisco Information Online (CIO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CIO to obtain additional content and services.
An important point after buying a device Cisco CX-TRIP2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco CX-TRIP2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco CX-TRIP2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco CX-TRIP2 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco CX-TRIP2 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco CX-TRIP2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco CX-TRIP2.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco CX-TRIP2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco CX-TRIP2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
