Instruction/ maintenance manual of the product A052041 CFM
Go to page of 24
F O R Y O U R S A F E T Y I f y o u sm e l l g a s: 1 S h u t o g a s to th e a p p l i a n c e . 2 E x t i n g u i sh a n y o p e n a m e . 3 O p e n l i d . 4 I f o d or c on t i n u e s, i m m e d i a te l y c a l l y o u r g a s su p p l i e r o r r e d e p a r tm e n t .
T able of Contents Page Number Chapter One - INSTALLATION 4 Necessary Information 4 Choosing a Safe Location 4 Portable L.P. Gas Grills 5 - 7 Important Features of the Series 4000 LP Gas Grill 8 L.
The gas fuel used by this product is highly flammable and must be used in a responsible and cautious manner . It is your responsibility to assemble, operate, and maintain your gas barbecue grill properly .
• The ventilation openings of the cylinder enclosure must be kept free and clear from other debris. 6. Do Not store a spare L.P. gas cylinder under or near this appliance. • Do not store an L.P. cylinder in a build- ing, garage or any other enclosed area.
2. The system has a thermal element that will shut off the flow of gas between 240° F and 300° F . 3. The system has a flow-limiting device which when activated, will limit the flow of gas to 10 cubic feet per hour . 4. The pressure regulator and hose assem- bly provided is factory set at an outlet pres- sure of 11 inches water column (.
L.P. GAS CYLINDER SPECIFICATIONS Any L.P. gas-supply cylinder used with this grill must be approximately 12 inches diameter and 18 inches high. The maxi- mum fuel capacity must be 20 pounds of propane. Full-cylinder weight should be approximately 38 pounds (43.
8 Rear view of Series A052041 grill with the heat shield, gaskets, collar assembly. HEA T SHIELD, GASKETS AND COLLAR W ARNING! Do not remove the heat shield, gaskets, collar assembly from the grill bottom.
Filling a Type 1 Cylinder Valve Example A: shows a CGA-510 POL fitting. Example B: shows using a Type 1 POL fitting. When using a cylinder exchange, be sure the exchanged cylinder is a T ype 1 cylinder; a 510 POL cylinder will not fit a T ype 1 regulator .
Assembly Instructions Chapter 2 Getting Star ted 1. Please follow the steps in the order that they are presented. 2. Assemble the grill where you plan to use it. 3. Y ou may want to place an old towel or cloth at the assembly site to prevent nuts and bolts from becoming lost.
A ssembly Instructions • Identify the G r ill Parts warming rack (1) cooking grid (1) ceramic briquettes ( 1 package ) rock grate (1) left side table (1) right side table (1) base (1) master hardwar.
HINT: For the first portion of the assembly you will be assembling the grill bottom, pillar and base up- side-down. 1. Position the grill bottom casting upside down so that the heat collar assembly is upward. 2. W orking from the back (open) side of the pillar, set the pillar upside down onto the collar assembly .
back hinge strut pillar bottom grill bottom back gas control valve ends fuel supply hose w/ regulator burner venturi tubes collar 13.
1. Lock the pre-assembled casters on base by pushing down on the latch. 2. Set the base upside-down on onto the pillar bottom as shown on the adjacent page, aligning holes in base with holes in pillar . 3. Insert six bolts through the holes in the pillar and base.
15 ignitor unit base back top pillar black lead wires heat shield bottom casting back.
1 Now with the help of an assistant carefully turn the grill assembly right-side-up. 2. IMPORTANT : Inspect beneath the grill bottom to check that the control-valve ends are still inside the burner venturi tubes. The valve ends must always be inside the burner tubes for the grill to safely operate.
17 A TTENTION PRODUCT ASSEMBLER: Install the X-brace retainer wire across the back of the pillar for warranty validation. 3. Position the wire ends “A” and “B” firmly into the pillar corners behind the bolt heads and against the base. (See Lower Detail.
Locate these parts: 18 tools needed: 3/8" open-end wrench 7/16" open-end wrench A ssembly Instructions • Install the Side T ables. 1/4-20 x 3/4” bolt ( 8 ) Use hardware bag “C”: 1/4-20 hex nut ( 8 ) right side table assembly ( 1 ) 1.
19 3. Insert four 3 /4" bolts through holes in the support brackets of the left side table assembly . 4. Attach the left side table to the four holes located in the left side of the grill bottom using the locking hex nuts provided.
20 A ssembly Instructions • Assemble the G rill Lid tools needed: 7/16" open-end wrench flat-blade screwdriver handle standoff ( 2 ) handle ( 1 ) 1. Position the back of the lid so that the rear holes are in line with the hinge struts on the back of the grill bottom.
7. Raise the lid to attach the front handle. 8. Attach a handle standoff to the front of the grill lid, as shown. 9. Insert one end of the handle into the hole of the standoff. 10.Place other standoff onto handle and while holding the handle in place assem- ble the opposite standoff to the lid in the same manner .
rock grate ( 1 ) No tools are needed. A ssembly Instructions • Installing the In ternal G rill Parts . 22 ceramic briquettes ( 1 box ) warming rack ( 1 ) 1. Place the single rock grate into the grill bottom. cooking grid ( 1 ) 2. Open the package containing the ceramic briquettes and place them on the rockgrate.
3. It is important to properly arrange all the ceramic briquettes onto the rock grate to allow for good air flow during use. NOTICE THE SPACING: The proper amount of briquettes are supplied and there is no need to add more. Some space between the briquettes is necessary.
Replacement parts are available direct from our warehouse. Some components are not available preassembled and may be ordered separately. For convenience, the following parts list is provided along with a representation of the items listed. Charges for replacement parts and shipping may apply .
35 Base Assembly Breakdown of P r eassembled Components Pillar Assembly Bottom/Burner Assembly Side T able Assemblies 1 Base Assembly consisting of: 1 Base SF AH000402 2 Locking Caster AH000303 2 Cast.
An important point after buying a device CFM A052041 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CFM A052041 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CFM A052041 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CFM A052041 you will learn all the available features of the product, as well as information on its operation. The information that you get CFM A052041 will certainly help you make a decision on the purchase.
If you already are a holder of CFM A052041, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CFM A052041.
However, one of the most important roles played by the user manual is to help in solving problems with CFM A052041. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CFM A052041 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
