Instruction/ maintenance manual of the product CARRIER 58CMA Carrier
Go to page of 12
58CMA Series 130 Multipoise Oil Furnace Installation, Start-up, and Operating Instructions NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since last issue. TABLE OF CONTENTS SAFETY CONSIDERATIONS .
ANSI/NFPA 31: INSTALLATION OF OIL BURNING EQUIPMENT ANSI/NFPA 211: CHIMNEYS, FIREPLACES, VENTS, AND SOLID FUEL BURNING APPLIANCES ANSI/NFPA 90B: WARM AIR HEATING AND AIR CONDITIONING SYSTEMS ANSI/NFPA 70: NATIONAL ELECTRICAL CODE CSA B139: INSTALLATION CODE FOR OIL BURNING EQUIPMENT CAS C22.
The air handling capacity of this furnace is designed for cooling airflow. Refer to Table 12 for expected airflows at various external duct static pressures. LOCATION Step 1 — General This furnace is not water tight and is not designed for outdoor installation.
Do not block combustion-air openings in the furnace. Any blockage will result in improper combustion which may result in a fire hazard and/or cause bodily harm.
opening must have a free area of at least 1 sq in. per 1000 Btuh of total input rating but not less than 100 sq in. (See Table 4.) ALL AIR FROM OUTSIDE OF STRUCTURE If outside air is supplied to a confined space, then the 2 openings must be equal and located as above.
2. Inspection to ascertain that vent system is clear and free of obstructions. Any blockage must be cleared before installing furnace. 3. Cleaning chimney or vent if previously used for venting a solid fuel burning appliance or fireplace. 4. Confirming that all unused chimney or vent connections are properly sealed.
24-V Wiring Instructions for wiring thermostat (field supplied) are packed in thermostat box. Make thermostat connections as shown in Fig. 3 or 4 at 24-v terminal board on fan timer board. Accessories When installing optional accessories to this appliance, follow manufacturer ’ s Installation Instructions included with accessory.
Fig. 3 — Wiring Diagram (105-12) A03164 X04031 Rev. A 8.
Fig. 4 — Wiring Diagram (120-20) A03165 X04032 Rev. A 9.
c. Use of an oversized nozzle input. d. Pump pressure over values listed in Table 10. 5. The CO 2 and stack temperature instruments enable you to obtain data required to determine thermal efficiency of fur- nace. 6. An oil filter should be installed as close to burner as possible with ALL oil burners and is essential on lower firing rate burners.
MAINTENANCE The ability to properly perform maintenance on this equip- ment requires certain expertise, mechanical skills, tools, and equipment. If you do not possess these, do not attempt to perform any maintenance on this equipment other than those procedures recommended in the User ’ s Manual.
4. Remove cover from control box and disconnect thermostat and power wires from the board. 5. Slide blower forward on rails toward front of unit. 6. Reverse items 1 through 5 to re-install blower. Refer to wiring diagram (Fig. 3 or 4) of these instructions or diagram located on inside of blower door to properly rewire unit.
An important point after buying a device Carrier CARRIER 58CMA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Carrier CARRIER 58CMA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Carrier CARRIER 58CMA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Carrier CARRIER 58CMA you will learn all the available features of the product, as well as information on its operation. The information that you get Carrier CARRIER 58CMA will certainly help you make a decision on the purchase.
If you already are a holder of Carrier CARRIER 58CMA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Carrier CARRIER 58CMA.
However, one of the most important roles played by the user manual is to help in solving problems with Carrier CARRIER 58CMA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Carrier CARRIER 58CMA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
