EN
AEG logo
Official user manual

AEG 50730

44 pages·645 KB·Dishwasher·PDF·ENDEFRITNLJA
AEG 50730
Table of Contents 61 sections FAVORIT 50730 · Dishwasher · User Instructions · Dear customer, · … ShowHide
FAVORIT 50730p.1Dishwasherp.1User Instructionsp.1Dear customer,p.2CONTENTSp.31 Safety Instructionsp.5Installation, Connection and Placing into Operationp.5Child Safetyp.5General Safetyp.5Correct Usep.62 Disposalp.7Disposing of the Packaging Materialp.7Disposal of Old Appliancesp.72 Economical and Ecological Dishwashingp.7Prior to using for the first timep.10Adjust the water softenerp.10Filling with Salt for the Water Softenerp.12SALEp.12SALTp.12SALZp.12SELp.12Rinse aidp.13To switch off the control indicator for rinse aidp.135. The L indicator shows the current setting:p.13The L indicator flashes: Control indicator switched on (factory setting)p.13The L indicator does not flash: Control indicator switched offp.13Filling with rinse aidp.14Adjusting Rinse Aid Dosingp.15In Daily Usep.16Loading Cutlery and Dishesp.16Loading Cutleryp.17Adjusting the Height of the Upper Basketp.21Filling with Detergentp.22Use of "3 in 1"/ Combi Detergent Tabletsp.23Detergent tabletsp.24Selecting the Wash Programme (Programme Table)p.25INTENSIVp.2570° NORMALp.2550° ECOp.2550° 3) 4) h 40° 30 MIN 5)p.25Start the wash programmep.26Interrupting or ending the wash programmep.26Pause functionp.27Setting or changing the delay start timerp.27Switching Off the Dishwasherp.28Emptying the Dishwasherp.28Care and Cleaningp.28Cleaning the Filterp.29Technical Datap.32INSTALLATION AND CONNECTION INSTRUCTIONSp.34Installing the Dishwasherp.34Built-Under Dishwasher (see enclosed installation instructions)p.34Connecting the Dishwasherp.36Water Connectionp.36Permitted water pressurep.36Connect the inlet hosep.36Water drainp.38Electrical Connectionp.40Connectionsp.41GUARANTEE CONDITIONSp.42SERVICE AND SPARE PARTSp.43
Page 1 of the AEG 50730 user manual — Dishwasher
Page 1 · click to enlarge
Page 1

FAVORIT 50730

Dishwasher

User Instructions

AEG 50730 — Dishwasher diagram (page 1)
Fig. 1 · Dishwasher
Page 2 of the AEG 50730 user manual — Dear customer,
Page 2 · click to enlarge
Page 2

Dear customer,

Please read these user instructions carefully. Please observe the safety instructions on the first few pages of these user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance.

1 The warning triangle and/or specific words (Warning!, Caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance. It is imperative that these instructions are observed. 0 This symbol or numbered instruction steps lead you step by step through the operation of the appliance.

3 Next to this symbol you receive additional information and practical tips on using the appliance.

2 Tips and instructions for the economical and environmentally conscious use of the appliance are marked with a clover leaf.

In the event of a malfunction, these operating instructions contain information on how to rectify faults yourself, see the "What to do, if..." section. If these instructions are insufficient, please contact your AEG Service Force Centre. In this respect please read the chapter "Service & Spare Parts".

Printed on paper manufactured with environmentally sound processes. He who thinks ecologically acts accordingly ...

Page 3 of the AEG 50730 user manual — Table of Contents
Page 3 · Contents
Contents

Contents

FAVORIT 50730p.1Dishwasherp.1User Instructionsp.1Dear customer,p.2CONTENTSp.31 Safety Instructionsp.5Installation, Connection and Placing into Operationp.5Child Safetyp.5General Safetyp.5Correct Usep.62 Disposalp.7Disposing of the Packaging Materialp.7Disposal of Old Appliancesp.72 Economical and Ecological Dishwashingp.7Prior to using for the first timep.10Adjust the water softenerp.10Filling with Salt for the Water Softenerp.12SALEp.12SALTp.12SALZp.12SELp.12Rinse aidp.13To switch off the control indicator for rinse aidp.135. The L indicator shows the current setting:p.13The L indicator flashes: Control indicator switched on (factory setting)p.13The L indicator does not flash: Control indicator switched offp.13Filling with rinse aidp.14Adjusting Rinse Aid Dosingp.15In Daily Usep.16Loading Cutlery and Dishesp.16Loading Cutleryp.17Adjusting the Height of the Upper Basketp.21Filling with Detergentp.22Use of "3 in 1"/ Combi Detergent Tabletsp.23Detergent tabletsp.24Selecting the Wash Programme (Programme Table)p.25INTENSIVp.2570° NORMALp.2550° ECOp.2550° 3) 4) h 40° 30 MIN 5)p.25Start the wash programmep.26Interrupting or ending the wash programmep.26Pause functionp.27Setting or changing the delay start timerp.27Switching Off the Dishwasherp.28Emptying the Dishwasherp.28Care and Cleaningp.28Cleaning the Filterp.29Technical Datap.32INSTALLATION AND CONNECTION INSTRUCTIONSp.34Installing the Dishwasherp.34Built-Under Dishwasher (see enclosed installation instructions)p.34Connecting the Dishwasherp.36Water Connectionp.36Permitted water pressurep.36Connect the inlet hosep.36Water drainp.38Electrical Connectionp.40Connectionsp.41GUARANTEE CONDITIONSp.42SERVICE AND SPARE PARTSp.43
Page 5 of the AEG 50730 user manual — General Safety
Page 5 · click to enlarge
Page 5

1 Safety Instructions

The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Neverthe- less, as a manufacturer we consider it our obligation to make you aware of the following safety information:

Installation, Connection and Placing into Operation

  • The dishwasher may only be transported upright.
  • Check the dishwasher for transport damage. Do not in any circumstances connect an appliance that is damaged. In the case of damage, please contact your retailer.
  • Before installing the appliance, ensure that the nominal voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate.
  • For information on how to correctly install and connect up your dishwasher, please read the “Installation“ section. Adaptors / connectors and extension cables must not be used.

Child Safety

  • This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product.
  • Keep all packaging away from children.
  • Keep all detergents in a safe place out of children’s reach.
  • The water in your dishwasher is not suitable for drinking. If there are still remnants of detergent in the appliance, there is a risk of burns!
  • When disposing of an old appliance, cut off the power supply cable and remove any door catches, to prevent young children being trapped inside.

General Safety

  • Repairs to the dishwasher are only to be carried out by qualified service engineers. Improper repairs can give rise to significant hazards for the user. If your appliance needs repairing, please contact your local AEG Service Force Centre.
Page 6 of the AEG 50730 user manual — Correct Use
Page 6 · click to enlarge
Page 6
  • Never place the dishwasher in operation if the mains cable, water inlet or drain hose is damaged; or the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible.
  • If the mains lead is damaged, or is to be replaced for a longer lead, the cable (obtainable from AEG Service Force) must be replaced by a service engineer authorised by AEG.
  • Never unplug the appliance by pulling on the cable, always pull the plug.
  • Additions or modifications to the dishwasher are not permitted for safety reasons.
  • Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves.
  • Long bladed knives stored in an upright position are a potential hazard.
  • Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket.
  • When finished loading or unloading, close the door as an open door can be a hazard.

Correct Use

  • Only wash household dishes using the dishwasher. If the appliance is used for other purposes, or is used incorrectly, the manufacturer cannot accept any liability for any damage caused.
  • Only use detergents specifically designed for use in domestic dishwashers.
  • Do not put any solvents in the dishwasher. There is a risk of an explosion!
  • The anti-flood system provides dependable protection against damage due to leaks. For this system to function correctly, the following preconditions must be met: – The appliance must remain connected to the mains even when it is

switched off. – The dishwasher must be correctly installed. – Always shut off the water supply at the tap when the dishwasher is

not to be used for longer periods, e.g. when you are away on holiday. • Do not sit or stand on the open door, the appliance may tip over.

Page 7 of the AEG 50730 user manual — 2 Economical and Ecological Dishwashing
Page 7 · click to enlarge
Page 7
  • In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently wired to the mains: remove the fuse.

2 Disposal

Disposing of the Packaging Material

  • Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled.
  • Plastic parts are marked with standard international abbreviations: – >PE< for polyethylene, e.g. sheet wrapping material – >PS< for polystyrene, e.g. padding material (always CFC-free) – >POM< for polyoxymethylene, e.g. plastic clips
  • Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling.

Disposal of Old Appliances

When disposing of old appliances, remove the plug and ensure that any locks or catches are removed to prevent young children becoming trapped inside. Use an authorised disposal site.

2 Economical and Ecological Dishwashing

  • Ensure that the water softener is correctly adjusted.
  • Do not pre-rinse dishes under running water.
  • When you wash a small load, the load sensor calculates the amount of water necessary and shortens the programme. It is more economical to always wash with a full load.
  • Select the wash programme to suit the nature and degree of the soiling on the dishes.
  • Do not use more detergent, special salt or rinse aid than is recommended in these operating instructions and by the detergent manufacturer.
Page 8 of the AEG 50730 user manual — 2 Disposal
Page 8 · click to enlarge
Page 8
AEG 50730 — 2 Disposal diagram (page 8)
Fig. 2 · 2 Disposal

Rubber Seal for Connecting the Water Feed to the Spray Arm

Page 9 of the AEG 50730 user manual — 2 Disposal
Page 9 · click to enlarge
Page 9
AEG 50730 — 2 Disposal diagram (page 9)
Fig. 3 · 2 Disposal

Indicator for the start delay set Set start delay Multi-display

Water softener and function button: In addition to the wash pro- grammes indicated, the dishwasher's water softening functions can be set and the control indicator for the rinse aid can be switched on/off by using a combination of these buttons.

The 3 multi-display lights can indicate: – the current stage of the wash

programme selected. – which fault has occurred on the

JRefill with special salt HRefill with rinse aid

3 The control indicators never light up while a wash programme is run- ning.

Page 10 of the AEG 50730 user manual — Adjust the water softener
Page 10 · click to enlarge
Page 10

Prior to using for the first time

Prior to using for the first time, remove all the clips with which the baskets are secured for transport. Then perform the following steps: 0 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3. Fill with Rinse Aid

Adjust the water softener

To prevent the build up of limescale on dishes and in the dishwasher, the dishes must be washed with soft water, i.e. water with a low lime content. For this reason the dishwasher is fitted with a water softener in which tap water from a hardness of 4 °d (German degree) is softened with the aid of special salt.

3 Your local water authority can advise you on the hardness of the water in your area. The water softener can be set manually using the water hardness switch; it can also be set electronically using the buttons on the control panel.

Water hardnessHardness settingNumber of flashes in °d1) in mmol/l2) Rangemanualelectronic 41 - 507.3 – 9.0IV155 30 - 405.3 – 7.2IV44 19 - 293.3 – 5.2III/IV0*3*3 4 - 180.7 – 3.2I/II/III22 under 4under 0.7I1 no salt required1

1)(°d) German degrees, a measure of water hardness 2)(ppm), parts per million *factory setting

Page 11 of the AEG 50730 user manual — Prior to using for the first time
Page 11 · click to enlarge
Page 11

Adjust the water softener to the water hardness setting for your area as shown in the table.

1 It is only possible to adjust the water hardness setting when no pro- gramme is running. If you have accidentally started a programme (a LED stays on permanently), the programme must be stopped by press- ing the appropriate button. 0 1. The dishwasher must be switched off. 2. Manual setting: Open the door on the dishwasher. 3. Remove the lower basket from the dishwasher. 4. Turn the water hardness switch to 0 or 1. 5. Re-position the lower basket. 6. Electronic setting: Press the softener and function but- tons simultaneously and keep them pressed. 7. In addition press the ON/OFF button. 8. The LED indicators for the water softener and function buttons flash. 9. Press the softener button again. – At first the LED indicator for the water softener button will light up

continuously for 5 seconds and then begin to flash. – The number of flashes corresponds to the hardness setting. – The sequence of flashes is repeated several times after a 5 second

pause. 10. Each time you press the water-softener button the hardness setting will go up by 1. (Exception: Hardness setting 1 follows hardness setting 5). – If the hardness setting is changed, the LED indicator for the water-

softener button will confirm the change by remaining illuminated continuously for 5 seconds and then flashing again. – The number of flashes corresponds to the new hardness setting. – The sequence of flashes is repeated several times after a 5 second

pause. 11. Once the hardness setting is correctly adjusted, press the ON/OFF but- ton. The hardness setting is then stored.

Page 12 of the AEG 50730 user manual — SALE
Page 12 · click to enlarge
Page 12

Filling with Salt for the Water Softener

1 Use only salt designed for dishwashers. Never fill the salt container with any another type of salt (e.g. culinary salt) or dishwasher deter- gent as this would irreparably damage the water softener. Prior to filling with salt, please check each time that you really do have a packet of dishwasher salt in your hand.

Fill with dishwasher salt: – Prior to using the dishwasher for the first time – When the SALT indicator J on the control panel is illuminated.

3 If the water hardness in your area is less than 4 °d, you do not need to use dishwasher salt. The SALT indicator J on the control panel will remain illuminated. 0 1. Open the door, remove the lower basket. 2. Undo the lid on the salt container by turning it anticlockwise. 3. When using for the first time: fill the salt container with water. 4. Place the funnel supplied on the con- tainer opening. Fill the container with salt through the funnel; the capacity of the con- tainer is approx. 1.0-1.5 kg depend- ing on the grain size. Do not overfill the salt container with salt.

SALE

SALT

SALZ

SEL

3 The water expelled by filling the salt container with salt runs out of the salt container onto the base of the washing compartment. This is not a cause for concern, the water will be pumped out at the start of the next wash programme. 5. Clean any salt remnants on the container opening. 6. Turn the lid clockwise to the stop, otherwise dishwasher salt will leak into the wash water, this could lead to poor wash results. To avoid this run a rinse programme after filling the salt container with special salt. This will wash away salt water and any salt crystals that have been spilt.

3 Depending on the size of the salt grains, it can take several hours for the salt to dissolve in the water and the special salt indicator J to extinguish. The setting of the water softener and the consumption of salt are dependent on the hardness of the local water.

Page 13 of the AEG 50730 user manual — 5. The L indicator shows the current setting:
Page 13 · click to enlarge
Page 13

Rinse aid

Rinse aid ensures thorough rinsing, spot and streak free drying of dishes and glassware.

  • Rinse aid can be added in one of two ways:
  • If you use the dishwasher detergent and rinse aid separately, add the rinse aid to the rinse aid container. If you opt for this method, please note that – the rinse aid container must never be empty. – the amount of rinse aid dispensed must be set.
  • If you use dishwasher detergent which already contains rinse aid, add this to the detergent compartment. If you opt for this method, please note that – the rinse aid container must be empty in order to avoid dispensing

too much rinse aid. – You can switch off the H control indicator. Otherwise, the H

control indicator would stay on permanently owing to the empty container.

1 Only use rinse aid specifically designed for domestic dishwashers. Never fill the rinse aid container with dishwasher detergent or any other sub- stance (e.g. vinegar essence) as this would damage the appliance.

To switch off the control indicator for rinse aid

0 1. The appliance must be switched off. 2. Press the softener and function buttons simultaneously and keep them pressed. 3. In addition press the ON/OFF button. The LED indicators for the function and water softener buttons flash. 4. Press the function button again. The LED indicator for the function button flashes.

5. The L indicator shows the current setting:

The L indicator flashes: Control indicator switched on (factory setting)

The L indicator does not flash: Control indicator switched off

6. Pressing the function button switches the control indicator on or off. 7. If the control indicator is set, press the ON/OFF button. The setting for the control indicator is then stored.
Page 14 of the AEG 50730 user manual — Filling with rinse aid
Page 14 · click to enlarge
Page 14

Filling with rinse aid

If you use dishwasher detergent and rinse aid separately, fill the rinse aid container: – Prior to using the dishwasher for the first time. – When the H indicator on the control panel lights up.

The rinse aid compartment is on the inside of the dishwasher door. 0 1. Open the door. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid.

4. Fill with rinse aid exactly up to the level marked “max”; this corresponds to a quantity of approx. 140 ml. 5. Close the lid and press until it locks into place. 6. Wipe up any spilt rinse aid with a cloth. Otherwise too much foam will be formed during the wash.
Page 15 of the AEG 50730 user manual — Adjusting Rinse Aid Dosing
Page 15 · click to enlarge
Page 15

Adjusting Rinse Aid Dosing

3 As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6. Only change the setting if streaks, milky spots or dried on water marks are visible on glasses or crockery.

0 1. Open the door of the dishwasher. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid. 4. Set the dose level. 5. Close the lid and press until it locks into place. 6. If rinse aid has spilt, wipe up with a cloth.

Page 16 of the AEG 50730 user manual — Loading Cutlery and Dishes
Page 16 · click to enlarge
Page 16

In Daily Use

  • Check the salt and rinse aid levels.
  • Load cutlery and dishes into the dishwasher
  • Fill with dishwasher detergent
  • Select a wash programme suitable for the cutlery and dishes
  • Start the wash programme

Loading Cutlery and Dishes

1 Sponges, household cloths and any object that can absorb water should not be washed in the dishwasher.

For washing in the dishwasher the following cutlery/dishes

are not suitableare of limited suitability:
  • Cutlery with wooden, horn, china or mother of pearl handles
  • Plastic items that are not heat resistant
  • Older cutlery with glued parts that is not temperature resistant
  • Bonded cutlery items or dishes
  • Pewter or copper items
  • Lead crystal glass
  • Steel items subject to rusting
  • Wooden platters
  • Items made from synthetic fibres
  • Only wash stoneware in the dishwasher if it is specifically marked as being dishwashersafe by the manufacturer.
  • Glazed patterns may fade if machine washed frequently.
  • Silver and aluminium parts have a tendency to discolour during washing. Left-overs, e.g. egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use.
  • Some types of glass can become dull after a large number of washes.
  • Before loading the dishes, you should: – Remove all scraps of food. – Soften remnants of burnt food in pans.
  • When loading the dishes and cutlery, please note: – Dishes and cutlery must not impede the rotation of the spray arms. – Load hollow items such as cups, glasses, pans, etc. with the opening

downwards so that water cannot collect in the container or a deep base. – Dishes and items of cutlery must not lie inside one another, or

cover each other

Page 17 of the AEG 50730 user manual — Loading Cutlery
Page 17 · click to enlarge
Page 17

– To avoid damage to glasses, they must not touch – Do not lay small objects (e.g. lids) in the cutlery rack

Loading Cutlery

1 Long bladed knives stored in an upright position are a potential haz- ard.

1 Long and/or sharp items of cutlery such as carving knives must be posi- tioned horizontally in the upper bas- ket.

1 Take care when loading or unloading sharp items such as knives. To ensure that all items of cutlery are completely washed, you should 1. Place the grid insert on the cutlery rack 2. Place short knives, forks and spoons in the grid insert with their handles pointing downwards.

Page 18 of the AEG 50730 user manual — Loading Cutlery
Page 18 · click to enlarge
Page 18
AEG 50730 — Loading Cutlery diagram (page 18)
Fig. 4 · Loading Cutlery

Load large and heavily soiled dishes in the lower basket (Plates up to 29cm in diameter).

Your dishwasher has one of the following four types of lower basket:

Type 1None of the plate inserts in the lower basket can be removed

Type 2: The right-hand plate inserts in the lower basket can be folded over to the left

3 To ease the loading of large items, the two right-hand plate inserts in the lower basket can be folded over to the left 1. Slightly lift the right plate inserts.

Page 19 of the AEG 50730 user manual — Loading Cutlery
Page 19 · click to enlarge
Page 19
Type 3The right-hand plate inserts in the lower basket can be folded across one another

3 To ease the loading of large items, the two right-hand plate inserts in the lower basket can be folded across one another.

Type 4: The two rear plate inserts in the lower basket can be folded across one another

3 To ease the loading of large items, the two rear plate inserts in the lower baskets can be folded across one another.

Page 20 of the AEG 50730 user manual — Loading Cutlery
Page 20 · click to enlarge
Page 20
AEG 50730 — Loading Cutlery diagram (page 20)
Fig. 5 · Loading Cutlery

Load small, delicate items and long pointed cutlery in the upper basket.

  • Arrange items of crockery on the folding cups racks so that they are offset from each other and water can reach all items.
  • The cup racks can be folded up out of the way for tall items.
  • Lay or hang wine, champagne, and brandy glasses in the cut outs on the cup racks.
  • Glasses, beakers, etc. can also be placed on the two rows of prongs on the left of the upper basket.
Page 21 of the AEG 50730 user manual — Adjusting the Height of the Upper Basket
Page 21 · click to enlarge
Page 21

Adjusting the Height of the Upper Basket

Maximum Height of the Dishes in the Upper Basket Lower Basket

With upper basket raised 22 cm 31 cm

With upper basket lowered 24 cm 29 cm

3 The height of the basket can also be adjusted when it is loaded.

Lowering the Upper Basket: 0 1. Pull the upper basket out completely. 2. Holding the upper basket at the rear right, lift it as far as it will go and then lower it vertically. The upper basket will engage in the lower posi- tion.

Raising the Upper Basket: 0 1. Pull the upper basket out completely. 2. Holding the upper basket at the rear right, lift it as far as it will go and then lower it vertically. The upper basket will engage in the higher posi- tion.

Page 22 of the AEG 50730 user manual — Filling with Detergent
Page 22 · click to enlarge
Page 22

Filling with Detergent

1 Only use dishwasher detergent.

Fill with detergent: – Prior to the start of a wash programme (not for the pre wash pro-

gramme). The detergent is released into the wash water during the programme.

2 Please observe the manufacturer's dosing and storage recommenda- tions as stated on the detergent packaging. The detergent compartment is on the inside of the dishwasher door. 0 1. If the lid is closed: press release button (1). The lid springs open.

2. Fill the detergent dispenser with detergent. The markings indicate the dosing levels: “20” corresponds to approx. 20 ml of detergent, “30” corresponds to approx. 30 ml of detergent. 3. Close the lid and press until it locks into place.

3 If the dishes are very heavily soiled put additional detergent into the adjacent chamber (2). This detergent will take effect during the pre wash.

Page 23 of the AEG 50730 user manual — Use of "3 in 1"/ Combi Detergent Tablets
Page 23 · click to enlarge
Page 23

Use of "3 in 1"/ Combi Detergent Tablets

General Advice These products are tablets with combined detergent/rinse-aid and salt functions. 0 1. Before using these products you should first check that the water hard- ness in your supply is compatible with the use of these products as per the detergent manufacturers instructions (on the product packaging). 2. These products should be strictly used according to the detergent manufacturers instructions.

1 Do not place the tablets in the tub or the cutlery basket as this will result in poorer wash results. The tablets should be placed in the detergent doser. 3. If you encounter problems when using "3 in1" products for the first time then please contact the detergent manufacturers care line (the telephone number is given on the product packaging).

  • Special Advice When using combination products, the rinse-aid and salt lights are no longer useful. It may be helpful therefore to switch the rinse aid off - please note that only some dishwashers have this facility - and selecting the lowest possible setting for water hardness. For more information please refer to your instruction manual. If you decide to switch to the use of a standard detergent system we advise that you:
  • Refill both the salt and rinse aid compartments.
  • Switch the waterhardness setting to the highest possible position and run for three normal cycles without a load.
  • Readjust the waterhardness setting again according to the conditions for your region (as per the instruction manual).
Page 24 of the AEG 50730 user manual — Detergent tablets
Page 24 · click to enlarge
Page 24

Concentrated Detergent Based on their chemical composition, dishwasher detergents can be split into two basic types: – conventional, alkaline detergents with caustic components – low alkaline concentrated detergents with natural enzymes.

2 The use of 50 °C wash programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes; these wash programmes are specially matched to the dirt-dissolving properties of the enzymes in the concentrated detergent. For this reason 50 °C wash programmes in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using 65 °C pro- grammes.

Detergent tablets

3 Detergent tablets of different makes dissolve at different speeds. For this reason some detergent tablets cannot develop their full cleaning power during short programmes. Therefore please use wash pro- grammes with pre wash when using detergent tablets.

Page 25 of the AEG 50730 user manual — INTENSIV
Page 25 · click to enlarge
Page 25

Selecting the Wash Programme (Programme Table)

Choose the most suitable wash programme with the aid of this table:

Type of dishes Dinner service and cooking utensils

in addition - with delicate

  • heavily soiled
  • normally soiled
  • lightly soiled
  • just used, average to lightly soiled
  • dried on leftovers, particularly egg white and thickeners

particularly suited to the use of

concentrated detergents.

Suitable wash programme:

INTENSIV

70° NORMAL

50° ECO

50° 3) 4) h 40° 30 MIN 5)

Pre wash Main wash 2x Intermedi- ate rinses Final rinse Drying

Pre wash Main wash Intermediate rinse Final rinse Drying

Pre wash Main wash Intermediate rinse Final rinse Drying

- Main wash Intermediate rinse Final rinse -

- Main wash -

Consumption levels2)

Duration 115 - 125 min. 90 - 100 min. 120 - 130 min. 40 min. 30 min.

Energy 2,0 - 2,2 kWh 1,05 - 1,24 kWh 0,95- 1,05 kWh 0,8 kWh 0,8 kWh

Water 21 litres 14 - 16 litres 14 - 16 litres 12 litres 8 litres

1) The noise level varies during different stages of the wash programme as at some stages the dishes are washed more energetically for a short period for better cleaning. 2) The consumption levels were tested under standardised conditions. They are dependent on how the racks are loaded. Variations from these figures are possible in practice. 3) Test programme 4) The “ECO 50°“ wash programme washes normally soiled dishes with a very low electricity consump- tion. If the dishes need to be washed more quickly, as an alternative you can use the “NORMAL 50°“ wash programme. 5) This programme is not suitable when left-overs have dried on.

Show 8 more labels / short text on this page
Dessert dishes · and coffee · Dishes without pans · service · glasses - · Type of soiling · Programme Sequence 1) · Final rinse -
Page 26 of the AEG 50730 user manual — Interrupting or ending the wash programme
Page 26 · click to enlarge
Page 26

Start the wash programme

0 1. Check that when the dishes and cutlery are loaded in the dishwasher the spray arms are free to rotate. 2. Open the water tap fully. 3. Shut the door. 4. Press the ON/OFF button. ON/OFF button indicator comes on. 5. Press the button for the programme required (see “Programme Table“). The programme indicator lights up. One or two lights will flash in the multi-display. During this time it is possible to reselect the programme. The selected washing programme begins after approx. 6 seconds. The current wash programme stage will always be shown in the multi-dis- play.

3 If the top light and/or the middle light in the multi-display flash after the programme has started please read the section “What to do, if...“.

Interrupting or ending the wash programme

3 Only interrupt a wash programme in progress if it is absolutely neces- sary. After the appliance door has been closed again the air that has entered will be quickly heated and expand. As a result water may pene- trate the base of the appliance and trigger the anti-flood system.

Interrupting the wash programme by opening the door of the dish- washer

1 Hot steam can escape from the appliance when the door is opened. Open the door carefully. 0 1. Open the door of the dishwasher. The wash programme will stop. 2. Lights are flashing in the multi-display. 3. Shut the door. The wash programme will continue.

Ending the wash programme 0 1. Press the button for the wash programme that is running and hold it down until the programme indicator for the wash programme goes out. 2. Release the programme button; the wash programme has been ended.

Page 27 of the AEG 50730 user manual — Setting or changing the delay start timer
Page 27 · click to enlarge
Page 27

Pause function

3 The pause function can only be initiated before the drying section of the programme I. If the pause function is initiated during the drying section of the programme I the wash programme is ended.

Using the pause function the dishwasher can be temporarily stopped: 0 1. Press the ON/OFF button. The wash programme will stop. 2. All indicators will go out. 3. After a short time when the wash programme is to continue, press the ON/OFF button again. The wash programme will continue.

2 The wash programme should not be stopped for a prolonged period or the cooled water will need to be reheated resulting in increased energy consumption.

Setting or changing the delay start timer

Using the delay start timer you can opt to set the wash programme to start in 3, 6 or 9 hours. 0 1. Press the ON/OFF button M. 2. Setting the delay start timer: Press the b button until the indicator next to the number of hours of delay illuminates. Changing the delay start timer: As long as the wash programme has not started, you can still change the delay start set by pressing the b button. Repeatedly press the b button until all three of the time indicators are off. The selected wash programme will begin immediately. 3. Press the button for the required wash programme. The programme indicator lights up. 4. After the set number of hours the wash programme will begin.

Load Sensing – Sensor Logic If a wash programme is started even though there are only a few dishes in the upper and/or lower basket, an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes. By this means it is possible to wash only a few dishes quickly and economically. At half load (6 place settings), up to 2 litres of water and 0.2 kWh of electricity are saved.

Page 28 of the AEG 50730 user manual — Care and Cleaning
Page 28 · click to enlarge
Page 28

Switching Off the Dishwasher

Switch off the dishwasher when L is illuminated on the programme progress display. 0 1. Press the ON/OFF button M. The ON/OFF button M indicator extin- guishes.

1 Hot steam may escape from the appliance when opening the door immediately after the end of the programme. 2. Open the door carefully.

Emptying the Dishwasher

  • The dishes should therefore be allowed to cool down before removing them from the appliance, as hot dishes may be sensitive to knocks.
  • Leave the dishes in the dishwasher for approx. 15 minutes after the end of the programme so that they dry better and can cool down.
  • First empty the lower basket, and then the upper basket. This will avoid any water that may be remaining in the upper basket, dripping onto the dishes in the lower basket and leaving water marks.

Care and Cleaning

  • 1 Do not under any circumstances use furniture care products or aggressive cleaners.
  • If necessary, clean the controls only with a soft cloth and pure warm water.
  • Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary.
Page 29 of the AEG 50730 user manual — Cleaning the Filter
Page 29 · click to enlarge
Page 29

Cleaning the Filter

3 The filters should be checked and cleaned regularly. Blocked filters will give poor wash results. 0 1. Open the door, remove the lower rack. 2. The dishwasher filter system com- prises a coarse/fine filter, microfilter and a flat filter. Unlock the filter sys- tem using the handle on the microfil- ter, and remove. 3. Turn the handle about ¼ a turn anti- clockwise and remove. 4. Take hold of the coarse/fine filter (1) by the handle with the hole and remove from the microfilter (2) 5. Clean all filters thoroughly under running water. 6. Remove the flat filter (3) from the base of the washing compartment and clean both faces thoroughly

7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment.

1 The dishwasher must not be used without filters under any circum- stances.

Page 30 of the AEG 50730 user manual — Cleaning the Filter
Page 30 · click to enlarge
Page 30

What to do, if ...

Try to rectify minor faults on the dishwasher with the aid of the instructions given here. If you call an engineer to resolve a of fault listed here, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is in guarantee.

...Fault warnings are displayed.

  • If the top or middle light in the display is flashing you can probably rectify the fault yourself. Once the fault has been rectified press the ON/OFF button. The wash programme will continue. If the fault is displayed again, contact your local AEG Service Force Centre.
  • If other lights flash in the multi-display, please contact your local AEG Service Force Centre stating which fault indicator is flashing.
SymptomPossible Cause Solution

The top light in the multi-

Tap is blocked or furred with lime-scale. Clean tap.

display is flashing.

The filter (where present) in the threaded hose fitting is blocked.

Clean the filter in the threaded hose fitting.

There is no water entering the dishwasher.

The water inlet hose is not correctly laid.

Check hose installation.

The middle light is flash-

The sink outlet is blocked. Clean the sink outlet.

ing in the multi-display.

The water drain hose is not correctly laid.

Check hose installation.

The top and the middle light are flashing

in the multi-display.

Close the tap and con- tact your local AEG Sevice Force Centre.

The anti-flood system has been triggered.

Page 31 of the AEG 50730 user manual — Cleaning the Filter
Page 31 · click to enlarge
Page 31

...there are problems operating the dishwasher.

Symptom Possible Cause Solution

The dishwasher door has not been closed properly. Shut the door.

Mains plug is not plugged in. Insert mains plug.

The programme does not start.

House fuse is faulty. Replace fuse.

For dishwasher models with delay start timer: Delay start has been selected.

If dishes are to be washed immediately cancel delay start timer.

The washing compartment is made of anticorrosive stain- less steel. Rust spots in the washing compartment are from particles from outside the appliance (rust particles from the water pipe, from pans, cutlery, etc.). Remove such spots with a commer- cially available stainless steel cleaner.

Only wash cutlery and dishes that are suitable for dish- washer use.

Spots of rust are visible in the washing com- partment.

Close the salt dispenser lid securely.

There is a whistling noise during washing.

The whistling is not a cause for concern.

Use a different brand of detergent.

...the wash results are unsatisfactory.

The dishes are still dirty. – The wrong wash programme was selected. – The dishes were arranged in such a way as to stop the water reaching

all parts of the surface. The dish racks must not be overloaded. – The filters in the base of the washing compartment are dirty or incor-

rectly positioned. – Too little or no detergent was used. – Where there are limescale deposits on the dishes: the special salt con-

tainer is empty or the water softener is incorrectly adjusted. – The drain hose is connected wrongly.

The dishes are wet and dull. – Rinse aid was not used. – The rinse aid container is empty.

Page 32 of the AEG 50730 user manual — Technical Data
Page 32 · click to enlarge
Page 32

There are streaks, milky spots or a bluish coating on glasses and dishes. – Decrease rinse aid dosing.

There are dried water drops on the glasses and dishes. – Increase rinse aid dosing. – The detergent may be the cause. Contact the detergent manufac-

turer's consumer advisor.

Technical Data

Capacity12 place settings including serving dishes
Permitted Water Pressure1-10 bar (=10-100 N/cm 2 = 0.1-1.0 MPa)

Electrical Connection: Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right.

DishwasherFree-Standing Appliances
Dimensions850 x 600 x 600 (H x W x D in mm)
Max. Weight54 Kg

Dishwashers that Can Be Integrated, Built-In Dishwashers

Dimensions820 – 880 x 596 x 570 (H x W x D in mm)
Max. Weight50 Kg

Dishwashers that Can Be Fully Integrated

Dimensions: 820 – 880 x 596 x 546 - 550 (H x W x D in mm)

Max. Weight50 Kg

; This appliance conforms with the following EU Directives: – 73/23/EWG dated 19. 02. 1973 – Low Voltage Directive – 89/336/EWG dated 03. 05. 1989

(including Directive Amendment 92/31/EWG) – EMC Directive

Page 33 of the AEG 50730 user manual — Technical Data
Page 33 · click to enlarge
Page 33
AEG 50730 — Technical Data diagram (page 33)
Fig. 6 · Technical Data

Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table).

Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table).

Half Load6 place settings incl. serving, leaving alternate positions free
Detergent Dosing5g + 25g (Type B) 20g (Type B)
Rinse Aid Setting4 (Type III) 4 (Type III)
Page 34 of the AEG 50730 user manual — Built-Under Dishwasher (see enclosed installation instructions)
Page 34 · click to enlarge
Page 34

Installation and Connection Instructions

INSTALLATION AND CONNECTION INSTRUCTIONS

Installing the Dishwasher

  • The dishwasher must be installed on a firm floor and adjusted such that it is stable and level.
  • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrewing: – use a screwdriver.
  • For built-in dishwashers the rear feet should be adjusted from the front of the appliance using a screwdriver.
  • The drain hose, inlet hose and mains cable must be laid such that they are free to move in the rear of the plinth recess, so that they cannot be kinked or crushed.

Built-Under Dishwasher (see enclosed installation instructions)

Free-Standing Appliances can be set up as stand-alone without additional installation.

1 If the dishwasher is set up next to a gas or coal cooker, a heat- insulating, non-flammable plate must be mounted between the dishwasher and the cooker, flush to the top edge of the work surface (depth 57.5 cm). The plate should have aluminium foil on the side fac- ing the cooker.

Page 35 of the AEG 50730 user manual — INSTALLATION AND CONNECTION INSTRUCTIONS
Page 35 · click to enlarge
Page 35

Installation and Connection Instructions

AEG 50730 — INSTALLATION AND CONNECTION INSTRUCTIONS diagram (page 35)
Fig. 7

If the dishwasher is installed underneath a kitchen work surface, the original work surface of the dishwasher is to be removed as follows: 0 1. Unscrew the screws from the posi- tioning plates on the back (1).

2. Slide the appliance's work surface approx. 1 cm to the rear (2).
3. Lift the work surface at the front (3) and remove.

1 If the dishwasher is later used as a free-standing appliance, the original work surface must be re-mounted. 3 The plinth on free-standing appliances is not adjustable.

Page 36 of the AEG 50730 user manual — Connect the inlet hose
Page 36 · click to enlarge
Page 36

Installation and Connection Instructions

Connecting the Dishwasher

Water Connection

  • The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations.
  • The dishwasher must be connected to a cold water supply.
  • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.

Permitted water pressure

Lowest permitted water pressure: 1 bar (=10 N/cm2 =100 kPa) Consult your installer if the water pres- sure is less than 1 bar.

Highest permitted water pressure: 10 bar (=100 N/cm2 =1 MPa) In the case of a water pressure greater than 10 bar, a pressure reduction valve must be used (available from your dealer).

Connect the inlet hose

1 The water inlet hose must not be kinked, crushed or entangled when it is being connected up. 0 Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread (¾ inch). Tighten the threaded hose fitting hand tight only.

  • In order that access to the tap in the kitchen is not limited by the use of the dishwasher, we recommend the installation of an additional tap, or fitting a two way adapter to the existing tap.
  • If you need a longer water inlet hose than that supplied, VDE approved complete hose sets are to be used. These are available from your local Service Force Centre.
  • Do not use, for connection, old hoses which have been used for another appliance.
Page 37 of the AEG 50730 user manual — Connecting the Dishwasher
Page 37 · click to enlarge
Page 37

Installation and Connection Instructions

3 The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap:

Water inlet hose with safety valve After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running water and the draining pump in the dishwasher is switched on.

1 Please take care when installing the water inlet hose: – The distance between the bottom

edge of the safety value and the floor on which the dishwasher is standing must be at least 30 cm: – The electrical cable for the safety

valve is in the double-walled water inlet hose. Do not immerse the water inlet hose or the safety valve in water. – If the water inlet hose or the safety

valve is damaged, remove the mains plug immediately. – A water inlet hose with safety valve

must only be replaced by your local Service Force Centre. – Place the water inlet hose in such a way that it is never higher than

the bottom edge of the safety valve.

Page 38 of the AEG 50730 user manual — Water drain
Page 38 · click to enlarge
Page 38

Installation and Connection Instructions

Water drain

1 The drain hose must not be kinked, crushed or entangled. • Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height 40 cm above the lower edge of the machine.

  • Extension hoses
  • Extension hoses are available from AEG Service Force. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded.
  • Hoses may be laid a maximum of 3 metres horizontally; the maximum permitted height for the connection for the drain hose is then 85 cm.
  • Sink outlet connection
  • The outlet of the drain hose (ø 19 mm) fits all commonly available sink outlet spigot types. The outer diameter of the spigot connection must be at least 15 mm.
  • The drain hose must be fixed to the sink outlet connection using the hose clamp supplied.

If the dishwasher is fitted at a high position If the dishwasher is installed at a high level, and the drainhose connec- tion is less than 30 cm from the bottom of the appliance, adapter kit ET 111099520 must be fitted. This is available from Customer Service.

Discharging into a standpipe When discharging into a standpipe, the upright standpipe should have a minimum, length of 30 cm (12“) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water.

Drain hose

Page 39 of the AEG 50730 user manual — Water drain
Page 39 · click to enlarge
Page 39

Installation and Connection Instructions

Leak Prevention System For protection from damage due to water leaks, the dishwasher is equipped with a leak prevention system, the AQUA CONTROL SYSTEM. In the event of a fault, the safety valve in the appliance immediately interrupts the inflow of water and the drain pump is activated. By this means water can neither escape nor overflow. The remaining water in the appliance is automatically pumped out.

1 The leak prevention system also works when the appliance is switched off, the appliance must however not be disconnected from the mains.

Page 40 of the AEG 50730 user manual — Electrical Connection
Page 40 · click to enlarge
Page 40

Installation and Connection Instructions

Electrical Connection

Any electrical work required to install this appliance should be car- ried out by a qualified electrician or competent person.

1 WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug. Important: The plug must still be accessible after the appliance has been installed. Changing a fuse The appliance is supplied with a 13amp plug fitted. In the event of hav- ing to change the fuse in the plug supplied, a 13amp ASTA approved (BS 1363A) fuse must be used. Should the plug need to be replaced for any reason, proceed as described below. The wires on the mains lead are coloured in accordance with the following code.

AEG 50730 — Electrical Connection diagram (page 40)
Fig. 8 · Electrical Connection
Green and YellowEarth Blue : Neutral Brown : Live
  • The wire coloured green and yellow must be connected to the terminal marked with the letter “E“ or by the earth symbol or coloured green and yellow.
  • The wire coloured blue must be connected to the terminal “N“ or coloured black.
  • The wire coloured brown must be connected to the terminal marked “L“ or coloured red.
  • Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.

1 WARNING! A cut off plug inserted into a 13 amp socket is a seri- ous safety (shock) hazard. Ensure that, if it is necessary to cut off the plug, it is disposed of safely and not retained.

Show 4 more labels / short text on this page
Green & Yellow · Blue · Brown · Cord Clamp
Page 41 of the AEG 50730 user manual — Connections
Page 41 · click to enlarge
Page 41

Installation and Connection Instructions

Connections

The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance. The plumbing and electrical installation example given below can only be regarded as a recommendation.

Two 45° or Straight Connections, Outer ø 19 mm, Length 30 mm Double tap Water drain Water inlet

Water drain Water inlet

Mains cable Mains socket

Mains cable

Page 42 of the AEG 50730 user manual — GUARANTEE CONDITIONS
Page 42 · click to enlarge
Page 42

GUARANTEE CONDITIONS

  • Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
  • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate.
  • The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions.
  • The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us.
  • All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or defective part replaced shall become the Company's property.
  • This guarantee is in addition to your statutory and other legal rights.
  • Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged. Exclusions This guarantee does not cover:
  • Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic.
  • Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom.
  • Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements.
  • Products of AEG manufacture which are not marketed by AEG. European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications:
  • The guarantee starts from the date you first purchased your product.
  • The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products.
  • This guarantee relates to you and cannot be transferred to another user.
  • Your new home is within the European Community (EC) or European Free Trade Area.
  • The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household.
  • The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances..

France Senlis +33 (0) 3 44 62 29 29

Germany Nürnberg +49 (0) 800 234 7378

Italy Pordenone +39 (0) 800 117511

Sweden Stockholm +46 (0) 8 672 5360

UK Slough +44 (0) 1753 219899

Guarantee Conditions

Page 43 of the AEG 50730 user manual — SERVICE AND SPARE PARTS
Page 43 · click to enlarge
Page 43

Service and Spare parts

SERVICE AND SPARE PARTS

In the event of your appliance requiring service, or if you wish to pur- chase spare parts, please contact Service Force by telephoning:

08705 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further informa- tion about Service Force, please visit the website at www.serviceforce.co.uk Before calling out an engineer, please ensure you have read the details under the heading „What to do if “ When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and post code. 2. Your telephone number 3. Clear and concise details of the fault. 4. The model and serial number of the appliance (found on the rat- ing plate).

5. The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls.

Customer Care For general enquiries concerning your AEG appliance or for further information on AEG products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.aeg.co.uk. Customer Care Department AEG Domestic Appliances 55-77 High Street Slough Berkshire, SL1 1DZ Tel. 08705 350350 (*) (*) Calls may be recorded for training purposes

Page 44 of the AEG 50730 user manual — SERVICE AND SPARE PARTS
Page 44 · click to enlarge
Page 44

From the Electrolux Group. The world´s No.1 choice.

The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.

AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg

http://www.aeg.hausgeraete.de

© Copyright by AEG

822 946 729 -00- 0203 Subject to change without notice

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
The top light in the multi- display is flashing. There is no water entering the dishwasher.Tap is blocked or furred with lime-scale.Clean tap. p.30
The top light in the multi- display is flashing. There is no water entering the dishwasher.The filter (where present) in the threaded hose fitting is blocked.Clean the filter in the threaded hose fitting. p.30
The top light in the multi- display is flashing. There is no water entering the dishwasher.The water inlet hose is not correctly laid.Check hose installation. p.30
The middle light is flash- ing in the multi-display.The sink outlet is blocked.Clean the sink outlet. p.30
The middle light is flash- ing in the multi-display.The water drain hose is not correctly laid.Check hose installation. p.30
The top and the middle light are flashing in the multi-display.The anti-flood system has been triggered.Close the tap and con- tact your local AEG Sevice Force Centre. p.30
The programme does not start.The dishwasher door has not been closed properly.Shut the door. p.31
The programme does not start.Mains plug is not plugged in.Insert mains plug. p.31
The programme does not start.House fuse is faulty.Replace fuse. p.31
The programme does not start.For dishwasher models with delay start timer: Delay start has been selected.If dishes are to be washed immediately cancel delay start timer. p.31
Spots of rust are visible in the washing com- partment.The washing compartment is made of anticorrosive stain- less steel. Rust spots in the washing compartment are from particles from outside the appliance (rust particles from the water pipe, from pans, cutlery, etc.). Remove such spots with a commer- cially available stainless steel cleaner.Only wash cutlery and dishes that are suitable for dish- washer use. p.31
Spots of rust are visible in the washing com- partment.Close the salt dispenser lid securely. p.31
There is a whistling noise during washing.The whistling is not a cause for concern.Use a different brand of detergent. p.31

Ask about the AEG 50730

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the AEG 50730

Be the first to ask — other owners or our team will answer.

Original document

AEG 50730 manual PDF

44 pages·645 KB·Dishwasher·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…