



Please read these user instructions carefully.
Above all please observe the safety instructions on the first few pages of these user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance.
The warning triangle and/or specific words (Warning!, caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance. It is imperative that these instructions are observed.
This symbol or numbered instruction steps lead you step by step through the operation of the appliance.
Next to this symbol you receive additional information and practical tips on using the appliance.
In the event of a malfunction, these operating instructions contain information on how to rectify faults yourself, see "What to do, when..." section.
If these instructions are insufficient, please contact your nearest customer service centre.
In the case of technical problems, our customer service organisation is available to provide you with assistance at any time.
Printed on paper manufactured with environmentally sound processes. He who thinks ecologically acts accordingly...


The safety of AEG electrical appliances conforms to accepted rules of technology and the Appliance Safety Act. We as manufacturers, however, see ourselves as being obliged to familiarise you with the following safety instructions.
Using your dishwasher for its intended purpose
G Only use your dishwasher for machine washing of household crockery. If
your machine is misused or used for any purposes other than that for which it is intended, the manufacturer cannot be held liable for any damage caused.
G For safety reasons, you should not convert or modify your dishwasher in
any way.
Before using your dishwasher for the first time
G Check your dishwasher for any transport damage. Never connect a
damaged machine. If your dishwasher is damaged, you should contact your supplier.
G Your dishwasher must be correctly installed and connected. Please read
the section on "Installation" to make sure you know all about this.
G Before using your dishwasher for the first time, do not forget that the
nominal voltage and current type indicated on the rating plate of your machine must be the same as the nominal voltage and current type at the installation site. The necessary electrical fusing is also given on the rating plate.
G Packaging parts (e.g. foils, styrene foam) may be dangerous for
children,who could even be suffocated! You should therefore keep all packaging well away from children.
G Children may not recognise the dangers of improper use of electrical
appliances. You should therefore ensure proper supervision during operation and not allow your children to play with your dishwasher.
G Detergents may have a caustic effect on eyes, mouth and throat and may
even cause suffocation! Keep all detergents in a safe place out of children’s reach.
Child safety

G The water in your dishwasher should not be used for drinking. Detergent
residues may still be present in your machine. Make sure you do not splash these caustic residues onto your skin or suffocate yourself! Keep children well away from your dishwasher when its door is open.
Your dishwasher in day-to-day use
G Never operate your dishwasher if the electrical supply lead, supply or
drainhose, control panel, worktop or plinth are damaged.
G If there is a fault, first turn the water tap off. Then switch off your
machine and pull the plug out of the socket. If there is a fixed connection, switch off or unscrew the fuse(s).
G Never pull the plug out of the socket by the cable - always hold the plug.
G Dishwasher repairs should only be performed by trained personnel.
Improper repairs may seriously endanger the user. If your dishwasher needs to be repaired, you should contact our service centre or your retailer.
G Never place any solvents in your dishwasher or you may cause an
G Do not rest or sit on the open door or the machine could tilt.
G Before using special dishwasher salt, detergent or rinse-aid, make sure
that the manufacturer of these products expressly specifies their use in domestic dishwashers.
G Always turn off the water tap when your dishwasher is left unattended
for any length of time, e.g. when you are away on holiday.
G Only transport the dishwasher in an upright position. Tipping it upside
down during transport could cause salty water to leak into the internal compartment and lead to the formation of rust.
explosion!

Our dishwashers require effective protective packaging in transit, though we always confine ourselves to what is absolutely necessary.
All packaging materials used are environmentally compatible and reusable. The cardboard parts are produced from recycled paper, and the wood is untreated. The plastics are marked as follows:
>PE< for polyethylene, e.g. packaging foils.
>PS< for polystyrene, e.g. padding (essentially CFC-Free).
>POM< for polyoxymethylene, e.g. plastic clamps.
Give the packaging for reuse to your local recycling centre. Your municipal or local authority will give you its address.
When your machine finally reaches the end of its life and you withdraw it from service, you should render it unserviceable before having it disposed of.
Marking of plastic parts for graded recycling: all plastic parts in your machine are marked with internationally standardised abbreviations (e.g. for polystyrene). When your machine is disposed of, this enables plastic waste to be sorted into individual types for environmentally conscious recycling.
Take your decommissioned machine to your local recycling centre or dealer, who will take it back from you for a small handling charge.

G Only connect the dishwasher to the hot water supply if your hot water is
not electrically heated.
G Ensure that the water softener is correctly adjusted.
G Do not pre-rinse under running water.
G Select the wash programme to suit the nature and degree of the soiling
on the dishes.
G Do not use more detergent, special salt or rinse aid than is recommended
in these operating instructions and by the manufacturer of the respective product.




If you select this option, washing will be confined to the only lower basket. In this case always remember to load crockery , cutlery, pots and pans only in the lower basket.

The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The higher the content of these salts, the harder your water is. Water hardness is measured in equivalent scales, German and French. The softener should be adjusted according to the hardness of the water in your area. To ensure optimum regeneration of the water softener: - the water softenening must be set to the local water hardness; - the dishwasher salt container must always be filled with special salt.
Your local Water Authority can advise you on the hardness of the water in your area. The dishwasher is factory set at level 2.
If this level is not suitable for your area the softener should be adjusted.

With a screwdriver turn the selector on the upper front corner of the machine until the level required corresponds with the marker.
If your water is level 0 it is already soft and therefore there is no need to use salt. In this case adjust the water softener on level 1 without using salt. The salt indicator on the control panel will always remain illuminated when the machine is switched on.
Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting one of the complete washing programmes (not the "Rinse and hold" programme). This will prevent any grains of salt or salty water, which may have been spilled, remaining on the bottom of the machine for any period of time, which may cause corrosion.

SALZ
SEL
When this has been done, all that is required is to periodically top up the container with salt.
The salt container will require topping up periodically. You are reminded of this by the salt indicator light on the control panel.
The salt indicator light on the control panel can remain illuminated for 2-6 hours after salt has been replenished, assuming the dishwasher remains switched on. If you are using salts that take longer to dissolve then this can take longer. The function on the machine is not affected.

The rinse-aid ensures brilliant crockery and also helps it to dry. It is automatically dosed in during the hot rinsing cycle. The storage compartment built in to the in side of the door can hold about 110 ml of rinse-aid, which will be sufficient for between 16 and 40 dishwashing programmes, according to the dosage setting.
Filling up the rinse-aid 1. Open the container by turning the lid (A) anticlockwise.
Ensure that the lid is closed after every refill.
Top up with rinse aid when the indicator (B) becomes clear.
Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash.
a · m

The correct dosage of the rinse-aid should be regulated on the basis of the shine and drying results.
For this purpose, set the quantity of liquid by means of the six-position selector (C) located on the inside of the filler opening (minimum quantity is position 1, maximum quantity is position 6).
Use the tip of a knife or a screwdriver to rotate the selector. If drops of water or white marks remain on the crockery after it has been washed, gradually increase the dosage. If the crockery comes out with whitish, sticky streaks, reduce the dosage.
Start from position 3.
m · a

Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher.
For washing in the dishwasher the following cutlery/dishes
are not suitable:
are of limited suitability:
G Cutlery with wooden, horn, china or
G Only wash stoneware in the dishwasher
mother of pearl handles.
if it is specifically marked as being dishwasher-safe by the manufacturer.
G Plastic items that are not heat resistant.
G Glazed patterns may fade if machine
G Older cutlery with cement that is not
temperature resistant.
washed frequently.
G Silver and aluminium parts have a
G Bonded cutlery items or dishes.
tendency to discolour during washing. Left-overs, e.g. egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use.
G Pewter or copper items.
G Lead crystal glass.
G Steel items subject to rusting.
G Wooden platters.
G Items made from synthetic fibres.
G Some types of glass can become dull
after a large number of washes.
Before placing dishes in the machine, remove any scraps of food, to avoid clogging the filters and consequently reducing the performance.
Do not load very small items which can fall through the baskets.
Open the door and slide out the baskets.


The lower basket is designed to take saucepans, lids, plates, salad bowls, cutlery etc.
Serving dishes and large lids should be arranged around the edge of the basket, ensuring that the upper spray arm can turn freely.
The two rear rows of prongs on the lower basket can be easily lowered to allow you to load pots, pans and bowls.
- Slightly pull them upward and let them drop down (see picture).
- To bring them back to the standing position, just pull them up again.

Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives.
Cutlery should be placed in the removable cutlery basket with the handles facing downwards. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing downwards.
Mix spoons with other cutlery to prevent the from sticking together.
Silver cutlery tends to go black if mixed with steel cutlery. Place it in the cutlery basket separate from the others.
Arrange spoons, dessert spoons, knives and other small items of cutlery in the racks on both sides of the cutlery basket.


The upper basket is designed for plates (dessert plates, saucers, dinner plates up to 24 cm in diameter), salad bowls, cups and glasses; these should be arranged as shown in the pictures.
Glasses with long stems can be placed upside-down in the raised cup-racks
Arrange items on and underneath the fold- down cup racks so that water can reach all surfaces.
Light items (plastic bowls etc.) should be loaded in the upper basket and arranged so they do not move.
Before closing the door, ensure that the spray arms can rotate freely.

If washing very large plates (over 27 cm and up to 31 cm in diameter) you can load them in the lower basket after moving the upper basket to the higher position.
To move to the higher position proceed as follows:
When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the raised cup racks.
After loading your machine always close the door, as an open door can be a hazard.

If using powder detergents proceed as follows:
Min = 15 g Max = 30 g
MIN
If using detergent in tablets proceed as follows:
At the end of any washing programme the lid is always open, ready for the next wash.
Since not all detergents are the same, you should also consult the instructions on the packet.

Remember that insufficient quantities of detergent will produce poor washing results whereas an excessive amount of detergent does not improve washing results and is also wasteful.
Using no more than correct amount of detergent also contributes to reducing pollution.
In these compact powders the environmentally unfriendly components have been replaced by natural enzymes and other more biodegradable substances. The enzymes deploy their full dirt dissolving power at a temperature as low as 50°C. By choosing the "Bio" programmes you can therefore achieve the same cleaning results that would otherwise be achievable only with 65°C programmes and conventional detergents. These new compact powders are generally phosphate-free. As phosphates have water softening properties, we suggest you add salt to the salt container even if the hardness of your water is as low as 4°dH (8°TH). This will avoid lime deposits on crockery and the inner tub.

Required push buttons Starting position of the
Type of soil Type of load
Heavy soil. Crockery, cutlery, pots and pans
Normal 65° with prewash
Normal soil. Crockery and cutlery
Normal 65° no prewash
Light soil. Crockery and cutlery
Light soil. Crockery and party crockery
Bio 50° with prewash
Normal soil. Crockery and cutlery
Bio 50° no prewash
Light soil. Crockery and cutlery
Light soil. Crockery and party crockery
Partial load to be completed later in the day. This programme does not require detergent.
Normal soil. Crockery, cutlery, pots and pans
Light soil. Crockery and party crockery
* These are special programmes for quick washing a full load of lightly soiled dishes, glasses and crockery (except pots) so that you may re-use them promptly.

in litres Cycle description
Hot prewash Main wash up to 70°C 2 cold rinses 1 hot rinse Drying Cold prewash Main wash up to 65°C 1 cold rinse 1 hot rinse Drying
101 ÷ 111 1.8 24
89 ÷ 99 1.4 19
Main wash up to 65°C 1 cold rinse 1 hot rinse Drying
81 ÷ 91 1.4 16
Main wash up to 65°C 1 cold rinse 1 hot rinse
43 ÷ 53 1.3 16
Cold prewash Main wash up to 50°C 1 cold rinse 1 hot rinse Drying
89 ÷ 99 1.24 19
Main wash up to 50°C 1 cold rinse 1 hot rinse Drying
81 ÷ 91 1.24 16
Main wash up to 50°C 1 cold rinse 1 hot rinse
31 ÷ 41 1.1 16
1 cold rinse (to avoid food scraps from sticking to the dishes).
6 0.1 10
Main wash up to 50°C 1 cold rinse 1 hot rinse Drying
81 ÷ 91 1.24 16
Main wash up to 50°C 1 cold rinse 1 hot rinse
31 ÷ 41 1.1 16
* The times and consumption values are intended as a guide, and depend on the pressure and temperature of the water and also by the variations of the power supply.

Close the dishwasher door Turn the programme selector dial clockwise until the letter of the programme you wish to select corresponds with the programme marker on the control panel. If necessary select the temperature of the main wash or the half load option according to the instructions in the "Washing programmes" chart (see "Required push buttons").

Turn the water tap on. Depress the On/Off push button. The On/Off indicator light will come on and the machine will start.
At the end of the washing programme the machine stops automatically. The On/Off indicator light remains on until the On/Off push button is depressed. Wait a few minutes before removing the dishes; in this way they will be cooler and drying will be improved.
Empty the lower basket first and then upper one; this will avoid water dripping from the upper basket the dishes in the lower one.

Do not under any circumstances use furniture care products or aggressive cleaners.
If necessary, clean the controls only with a soft cloth and pure warm water. The spray arms do not need cleaning. Occasionally check the internal containers, door seal and water inlet for soiling, clean if necessary. We recommend every 3 months to run a 65°C wash programme without dishes using detergent.
Scraps of food may accumulate in the drain filter (A) and should be removed by rinsing the filter under running water.
To remove the drain filter
- simply pull it out by the handle.
Once cleaned, refit the filter by pushing it back to its original position until it engages.
MA04 MA19

If necessary clean the large filter (B) on both sides under running water, using a brush.
To remove the large filter
MA21
MA18
Under no circumstances may the dishwasher be used without filters. Incorrect repositioning and fitting of the filters will produce poor washing results. Cleaning the filters is vital to ensure correct operation of the machine.

What to do, when...
Before calling our Service Centre try to rectify minor faults on the dishwasher with the aid of the instructions given here.
Should this information be of no assistance to you in a specific case, please contact our Service Centre.
The plug is not properly inserted in the power socket.
Insert the plug.
...the programme does not start
There is no current at the socket.
The door is not properly closed.
Close the door.
The water tap is closed. Open the water tap.
the dishwasher does not fill with water
The mains water supply has been cut off.
The inlet hose may be squashed or bent.
Reposition correctly the hose.
The drain hose may be squashed or bent. The drain hose extension is not correct.
Reposition correctly the drain hose. Follow the instructions for connecting to the waste.
the dishwasher will not drain
The sink may be blocked. Clear any blockages.
Dishes are rattling against each other. The spray arms are knocking against the dishes.
Load correctly crockery, cutlery, pots and pans. Refer to "Loading cutlery and dishes"
the machine is noisy
the door is difficult to close
The dishwasher is not level, or not properly built-in.
Refer to "Installation" instructions.
Malfunction · Possible cause Remedy

Visible lime deposits or white film on the dishes
G Check that the right level of the water softener is setted.
G Check that there is salt.
The dishes are not quite dry
G The rinse aid has run out or too little is being used.
The dishes are not clean
G The baskets are too full.
G The dishes have not been arranged properly.
G The spray arms do not rotate because incorrect loading of the baskets.
G The filters are clogged.
G The filters are not in the correct position.
G Not enough detergent has been used or it is unsuitable.
G The detergent is old or has gone hard.
G The salt container cap is not properly closed.
G The washing programme is too gentle.

In the section "What to do, when...", we have listed the most important faults which you can rectify yourself. Should you still wish to call our Service Centre for any of the specified faults or because the appliance is being wrongly operated, the service engineer's visit cannot be made free of charge even during the guarantee period.
Should you find no reference to a fault in the operating instructions, you should call our Service Centre.
When making your call, quote the E-No. (product number) and F-No. (serial number) indicated on the rating plate. It is located on the right inside edge of the door.
Mod
Prod.No Ser. No
F-NR E- NR
To keep these numbers handy, we recommend you enter them here.
E-No
F-No
Your specifying these details enables the Service Centre to make precise identification of the spare part required so that the appliance can be repaired at the service engineer's first visit without your having to pay extra costs for repeated journeys by the service engineer.

Width 60 cm Height with worktop 85 cm Height without worktop 82 cm Max depth 60 cm Max depth with open door 115.9 cm
Electrical connection Motor rating during wash Power of heating element Overall power
230 V - 50 Hz 200 W 2100 W 2300 W
Minimum 50 kPa (0.5 bar) Maximum 800 kPa (8 bar)
This appliance complies with the following E.E.C. Directives: - 73/23/CEE of 19/02/73 (Low Voltage Directive) and subsequent modifications; - 89/336/CEE of 03/05/89 (Electromagnetic Compatibility Directive) and subsequent modifications.


Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser.
- 25 g in the dispenser - 5 g on the dispenser lid

You can move the worktop forward or backward by 25 mm in order to align the machine with other kitchen units. Simply unscrew the two rear retaining screws, move the top to the required position and then retighten the screws.
Fitting under a counter (kitchen worktop or sink)
By removing the machine’s worktop, you can install it under a close fitting sink unit or a pre-existing top, providing the dimensions of the recess correspond to those shown in the picture.
Proceed as follows:
- Remove the machine’s worktop by
unscrewing the two rear retaining screws, pull from the front and slide out the rear slots, lifting the worktop.
- Insert the machine after adjusting
height and levelling with the adjustable feet. When inserting the machine, ensure that the water inlet and drain hoses are not kinked or squashed.
Levelling
Good levelling is essential for correct closure and sealing of the door.
When the appliance is correctly levelled, the door will not catch on the levelling spacers on either side of the cabinet.
If the door does not close correctly, loosen or tighten the adjustable feet until the machine is perfectly level.

Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. Remove all packaging before positioning the machine. If possible, position the machine next to a water tap and a drain.
This dishwasher may be fed with either hot (max. 60°C) or cold water. Nevertheless we advise a cold water supply. A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes. Feeding the appliance with a hot water supply (max. 60°C) will allow you to obtain considerably shorter programmes. The water pressure must be within the limits given in the technical specifications. Your local Water Authority will advise you on the average mains pressure in your area. The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation. The locknut must be correctly fitted to avoid water leaks. Avoid bends or kinks in the hose which could prevent or slow down the water supply. If the machine is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose. This will prevent deposits of sand or rust clogging the inlet hose filter. For making the connection itself, the coupling nut fitted to the machine’s supply hose is designed to screw onto either a 3/4" inch gas thread spout, or to a purpose made quick-coupling tap such as the Press-block.

The end of the drain hose can be connected as follows:
Ø 18
CS09
The waste connection must be at a height of between 30 cm (minimum) and 100 cm (maximum) from the floor. It makes no difference which way the drain hose faces, either to the right or left of the dishwasher. Avoid bending or kinking the hose as this could prevent or slow down the discharge of water.

The necessary extension hoses can be obtained from specialist shops or from our technical assistance centres.
The extension hose must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided.
Likewise the internal diameter of the couplings used for connection to the waste outlet must be no smaller than the diameter of the drain hose.
Arrange the extension hose horizontally along the floor and allow it to rise only where it is to be connected to the drain.
Ø 21
+ 2 m max
Electrical connection
Before plugging the appliance into the wall socket, make sure that:
Make sure that the socket and plug are compatible without having to use any type of adaptor. If necessary, have the domestic wiring system socket replaced.
Safety standards require the appliance to be earthed. The Manufacturer accepts no liability for failure to observe the above safety precautions.
max 100 cm · max 100 cm · min 30 cm







AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg
© Copyright by AEG 152982 05/1 GB
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.