Instruction/ maintenance manual of the product 9W111-08 Cabletron Systems
Go to page of 28
MMAC-Plus ™ 9W111-08 Eight Port WAN Router User’s Guide.
.
i Notice Notice Cabletron Systems r eserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made.
ii Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation.
iii Notice DOC Notice This digital apparatus does not exceed the Class A limits for radio noise emissions fr om digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
iv Notice.
v Contents Chapter 1 Intr oduction Features........................................................................................................................... 1-1 Related Manuals ................................................................
Contents vi.
1-1 Chapter 1 Intr oduction The 9W1 1 1-08 W AN Router module, shown in Figure 1-1, is a eight port W ide Area Net r outer . Up to eight front panel network connections can be made to this module and they can be routed to any other port and to any other MMAC-Plus module via the FNB bus.
Introduction 1-2 Management Information Base (MIB) Support All concentrator modules provide MIB support including the following: • IETF FDDI MIB • IETF MIB II LANVIEW LEDs The 9W1 1 1-08 uses LANVIEW: the Cabletron Systems built-in visual diagnostic and status monitoring system.
1-3 F eatures Figure 1-1. The 9W111-08 Module MMAC PLUS.
Introduction 1-4 Related Manuals The manuals listed below should be used to supplement the procedur es and technical data contained in this manual. MMAC-Plus Installation Guide MMAC-Plus Operations Gu.
2-1 Chapter 2 Installing the MMA C-Plus Module The MMAC-Plus module may be installed into any of the 14 slots that are available. T o install, follow the steps below: 1.
Installing the MMA C-Plus Module 2-2 Figure 2-1. Installing the MMAC-Plus Module 7 FLNK 8 FLNK FLNK 10 FLNK INS 11 FLNK INS 12 RX TX RX TX RX Circuit Card Card Guides Metal Back-Panel Jack for ESD wrist strap Plastic T abs W arning: Ensure that the circuit card is between the card guides .
2-3 The Reset Switch The Reset Switch The Reset switch is located on the front panel, under the top plastic tab, as shown in Figure 2-2. It serves two functions: • Pressing the Reset switch twice within thr ee seconds causes the processor to reset. • Pressing and holding the switch on for thr ee or more seconds causes the module to shutdown.
Installing the MMA C-Plus Module 2-4 Setting the FNB Switch The 9W1 1 1-08 module can attach to ether FNB-1 or FNB-2. Figure 2-3 shows the location of the FNB switch, SW201. When this switch is up (toward the top of the module) the 9W1 1 1-08 attaches to FNB-2.
2-5 Local Management Console T able 2-1. T erminal Setup Requirements Menu Function Selection Display Columns 80 Columns Setup: Controls Interpret Controls Auto Wrap No Auto Wrap Text Cursor Cursor Ge.
Installing the MMA C-Plus Module 2-6 An RJ-45 connector provides a COM interface to the management terminal. Figure 2-4 shows the pinouts. Figure 2-4. Console Cable Pinouts Connect the console to the module as follows: 1. Attach the male RJ-45 connector to the COM port of the 9W1 1 1-08.
3-1 Chapter 3 Operation The 9W1 1 1-08 W AN Router module is a eight port W ide Ar ea Net router . Up to eight front panel network connections can be made to this module and they can be routed to any other port and to any other MMAC-Plus module via the FNB bus.
Operation 3-2 Fle xible Netw ork Bus (FNB) The FNB consists of two dual FDDI networks, the FNB-1 and FNB-2, providing up to 400 Mbps of data bandwidth. These FDDI networks are 100% ANSI FDDI- compliant, supporting SMT (version 7.3), MAC, PHY , and PMD standards.
3-3 FNB Interf ace FNB Interface MMAC-Plus modules are designed with one of two attachment policies. One allows dual attachment of a module to either FNB-1 or FNB-2; the second allows dual attachment to both FNB-1 and FNB-2. The 9W1 1 1-08 has one dual attachment to the FNB backplane, connecting to either FNB-1 or FNB-2.
Operation 3-4.
4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs, shown in Figur e 4-1, indicate the status of the module and may be used as an aid in troubleshooting.
LANVIEW LEDs 4-2 The functions of the System Management Bus (SMB) and CPU LEDs are listed in T able 4-1. * At least one W AN port in both groups 0-3 and 4-7 ar e down. The function of the FNB Receive LED is listed in T able 4-2. The function of the FNB T ransmit LED is listed in T able 4-3.
4-3 LANVIEW LEDs The functions of the W AN Status LEDs are listed in T able 4-4. The function of the W AN Activity LEDs are listed in T able 4-5. T able 4-4.
LANVIEW LEDs 4-4.
5-1 Chapter 5 Specifications Safety This equipment meets the following safety requir ements: • UL 1950 • CSA C22.2 No. 950 • EN 60950 • IEC 950 • EMI Requirements of FCC Part 15 Class A •.
Specifications 5-2 Ph ysical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters (13.8 D x 17.4 H x 1.2 W inches) W eight Unit: 1.36 kg. (3 lb) Shipping: 1.
An important point after buying a device Cabletron Systems 9W111-08 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cabletron Systems 9W111-08 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cabletron Systems 9W111-08 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cabletron Systems 9W111-08 you will learn all the available features of the product, as well as information on its operation. The information that you get Cabletron Systems 9W111-08 will certainly help you make a decision on the purchase.
If you already are a holder of Cabletron Systems 9W111-08, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cabletron Systems 9W111-08.
However, one of the most important roles played by the user manual is to help in solving problems with Cabletron Systems 9W111-08. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cabletron Systems 9W111-08 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
