Instruction/ maintenance manual of the product LH 3 Burris
Go to page of 48
HP NetServer LH 3, LH 4, LH 3000, and LH 6000 Pedestal-to-Rack Conversion Guide HP Part Num ber 5969-2162 Printed in Novem ber 1999.
ii Notice The information contain ed in this document is subject to change w ithout notice. Hewlett-Packard m ake s no warranty of any kin d with regard to this m ateria l, including, but not limited to, the implied warranties of m erchantability a nd fitness for a particular purpo se .
iii Contents Preface ...................................................................................................................1 About this Guide ................................................................................................
Contents iv 4 Warranty and Support.................................................................................... 39 Hardware Accessories Lim ited W arranty ......................................................... 39 Hewlett-Packard Hardware Accessories .
1 Preface A bout this Guide Thi s gui de d escr i b es ho w to c o nvert the pe desta l co nfi gurati o n HP N etSer ver LH 3, L H 4, LH 3000, or LH 6000 t o the rack- optimized con figu ration HP NetServ er LH 3r, LH 4r, L H 3000r, or LH 6000r.
Chapter Preface 2 Related Documentation The following documents describe the NetServer: • HP NetServer LH 3/LH 3r Us er Guide • HP NetServer LH 4/LH 4r Us er Guide • HP NetSer ver LH 3000/3000r .
3 1 Introduction Ov erview This guide des cribes the procedure for con verting the HP NetServer L H 3, LH 4, LH 3000, an d LH 6000 (pedestal con figu ration) to th e HP NetServer L H 3r, LH 4r, L H 3000r, or LH 6000r (rack- optim ized config uration).
Chapter 1 Introduction 4 5. Rem ove the plastic lock paw l (w hich eng ages and secu res the bezel lock mech anism) f rom the NetServ er chassis f ront. Unfasten the control panel from the chassis, reorien t it, and then secu re it to the chassis again.
Chapter 1 Introduction 5 WA RNING To prevent the rack enclos ure from tipping over: • Extend the anti- tip foot or verify that the an ti-tip feature is installed. • Verify that the leveler feet are low ered. • Do NOT extend more th an one piece of equi pment at a time out f rom the front of th e rack.
Chapter 1 Introduction 6 Verify Contents Unpack an d verify the contents of the shippin g box. If an ythin g is m issing or damaged , co ntact your rese ller . The conversion kit includes tw o assem bly kits , one for HP racks, and on e for Compaq racks.
Chapter 1 Introduction 7 The assembly k it for HP racks includes the follow ing hardw are: • Front bezel for the NetServ er in the HP rack config uration • Bezel hinge plate an d bezel hinge f or .
.
9 2 Remov e Bezel, Cov er, and Components Ov erview of Removal of Front Bezel, Rack Rail Cov er, and Components Before you conv ert the NetServer to the rack-optim ized configuration, y ou will do the followi ng: • Power dow n the NetServ er and disconnect it.
Chapter 2 Remove Bezel, Cover, and Components 10 WA RNING Before removin g the cover, alw ay s disconnect th e power cord(s) and un plug telephon e cables. Disconnect th e power cord(s) to avoid expos ure to high energy levels that m ay cau se burns w hen parts are short-circu ited by m etal objects, such as tools or jew elry .
Chapter 2 Remove Bezel, Cover, and Components 11 Remov e the Front Bezel and Rack Rail Cover The rack rail cover is th e only NetServe r cover that mu st be remov ed during the conve r sio n o f the N e tSer ver fr om ped esta l c onfigur atio n to r ack c onfigur a tio n.
Chapter 2 Remove Bezel, Cover, and Components 12 Pull Here Bezel Lock Rack Rai l Cover Figure 2-1. Remove Front Bezel Remov e the Rack Rail Cov er Rem ove the rack rail cover, as s how n in Figure 2- 2: 1. Unscrew th e screw on the fron t of the cov er.
Chapter 2 Remove Bezel, Cover, and Components 13 Unscrew Rack Rail Cove r 1 2 3 Figure 2-2. Remove the Rack R ail Cover.
Chapter 2 Remove Bezel, Cover, and Components 14 Lighten the NetServ er Before you lif t the NetServer, remove th e hot-sw ap hard disk drives and power supply m odules. This will lighten the NetServer, so that few er people will be needed to lift it.
Chapter 2 Remove Bezel, Cover, and Components 15 Locking L atch Ejecto r Handle Figure 2-3. Remove Har d Disk Drives From the NetSer ver Remove Power Supply Modules To remove the pow er supply m odules, uns crew the m odules an d pull them away from th e NetServer, as shown in Figure 2-4.
Chapter 2 Remove Bezel, Cover, and Components 16 Figure 2-4. Remove Power Supply Modules (Rear View of HP NetServer LH 3 Shown; Number of Powe r Supply Modules May Vary ).
Chapter 2 Remove Bezel, Cover, and Components 17 Mov e the NetServer Using eno ugh pe o ple for sa fe hand ling, l i ft the Ne tSer ver o nto a n empty work surface f or easy access to the interior and to the f ace of the chass is. Rotate the NetServ er so that Cov er 1 is now on top, as show n in F igure 2-5.
.
19 3 Conversion: Install Components, Cover, and Front Bezel Ov erview of Conversion to Rack-Optimized Configuration To complete the conversion of the NetServ er to the rack-optimized config uration, you w ill do the following : • Install any additional memory or accessory boards.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 20 Install the Lifting Handles Install lifting handles for use w hen y ou mount the NetServer on the rack slides. The four ha ndles mount t wo to a sid e. Use the provided screws to m ount the handles, as show n in Figu re 3-1.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 21 Reorient the Control Panel The control panel must be repositioned to be easily readable in the rack- mount position. Reposition the control panel and its bezel, as follows: 1. Unscrew th e two screw s securing th e control panel to the chassis.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 22 4. Rotate the control panel until it is aligned w ith the rack position of the NetServe r, as show n in F igure 3- 3. Be careful of the ribbon cable t hat connects the control panel to the NetServ er.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 23 As y ou m ount th e control panel, en sure that the ribbon cable g oes comple tely back inside th e NetServer. Do n ot damage t he ribbon cable w ith the control panel. 6. Replace the tw o screw s to secure the con trol panel to the chas sis.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 24 Install the NetServ er in the Rack Refer to the documen tation listed belo w to install th e slides in the rack and to install the NetServer into th e rack: • To install into an HP ra ck: Refer to the NetSe rver 's user guid e or installation guide .
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 25 3. Mark locations on the rack colum ns for all bar nuts an d rack nuts to hold the rack slides and bezel moun ting hardw are.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 26 Rack Nuts Ri ght Rear Co lumn of HP Rack Hole 13 abov e Base Line Hole 9 above Base Line Figure 3-5. Position Rack Nuts for Chassis R etention Bracket 5. Install the rack slides (slide m embers).
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 27 WA RNING Do not attempt to lift the NetServer by yourself. Follow local regulations w hen lif ting the NetServer. Failure to observe this w arning could result in serious injury to personnel or dam age to equipment.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 28 Bezel Hi nge Latch Asse mbly Figure 3-6. Mounting Hardware for Front Bezel for HP R ack ◊ For the Com paq rack , the bezel m ounting hardware is the left and right reces sed brackets, as sh own in Figure 3- 7.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 29 Compaq Rack Figure 3-7. Mounting Hardware for Front Bezel for Compaq Rack A ttaching the Cable Management A rm The Cable Managem ent A rm for the HP NetServ er can only be m o unted on HP Sys tems racks .
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 30 Left Rear Rack Co lumn Rear o f Net Ser ver Cab le M ana geme nt Arm Figure 3-8. Attaching the Cable Management A rm 3. Install the tw o 6-32 T orx T-15 screws in the tw o threaded holes o n the rear of the NetServer.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 31 10. Plug the HP NetServer's power cable an d all available data cab les into the back of th e HP NetServer. Replace Pow er Supply Modules and Hard Disk Driv es Do the follow ing to replace th e power s upply m odules an d hot-sw ap hard disk drive m odules : 1.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 32 Install Chassis Retention Bracket w hen Shipping an HP Rack For the HP rack, the rack n uts for the ch assis retention bracket w ere installed on the right rear rack colum n. For the HP rack, install th e chassis reten tion bracket and secure th e NetServer to it, as follows: 1.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 33 Install the New Front Bezel The conversion kit contains tw o assembly kits, one for th e HP rack, and one for the Com paq rack. Each assem bly kit con tains the new front bezel for the NetServer in th e specific type of rack, as show n in Figure 3-10.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 34 2. Secure the nam eplate to the fron t bezel, as follow s: ◊ For the HP rack front bezel, in sert the tab at one en d of the nam e.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 35 A ttach the Front Bezel After th e new front bezel is prepared, pus h it into place, as sh own in Figure 3-11 or 3-12.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 36 Figure 3-12. Push Front Bezel into Place on Compaq Rack.
Chapter 3 Conversion: Install Components, Cover, and Front Bezel 37 Reconnect the Pow er Cords and Cables Complete the installation of th e NetServer, as follows: 1. If y ou remov ed the door of the rack , replace it. 2. Reconn ect the AC pow er cord(s) and oth er external cables as des cribed in the Rack Cabling Ref erence for yo ur HP NetServer.
.
39 4 Warranty and Support The hardw are warran ty below applies to components purchased as accessories. If you r componen t was f actory ins talled as part of an HP NetServer m odel, refer to the w arranty statemen t provided with your sy stem documen tation.
Chapter 4 Warranty and Support 40 Refer to the w arranty statem ent provided with y our original HP NetServer system documentation f or the warran ty lim itations, customer responsibilities, and other terms an d conditio ns. Third-Party Hardw are Products HP does not w arrant third- party h ardware produ cts.
41 A Regulatory Information For regulatory inform ation pertainin g to this HP accessory , please refer to the regulatory section of th e user guide f or the NetServer in w hich th is accessory is installed.
.
43 Index A Accessory bo ards, insta lling, 21 Access ory kit conten ts, 8 Anti- tip feature, 26 Anti- tip foot, 26 Ar m, c a b le ma na ge me nt , 3 1 Assem bly kit for Com paq racks, 9 Assem bly kit .
Index 44 N Nam eplate, 35 O Overvi ew, gener a l, 5 P Power cord retain er, 39 Pow er supply module s removing, 17 replacing , 33 Pow ering dow n, 11 Processor label , 35 R Rack door, 26, 39 Rack encl.
An important point after buying a device Burris LH 3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Burris LH 3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Burris LH 3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Burris LH 3 you will learn all the available features of the product, as well as information on its operation. The information that you get Burris LH 3 will certainly help you make a decision on the purchase.
If you already are a holder of Burris LH 3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Burris LH 3.
However, one of the most important roles played by the user manual is to help in solving problems with Burris LH 3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Burris LH 3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
