Instruction/ maintenance manual of the product 30235 Briggs & Stratton
Go to page of 48
SA VE THESE INS TR UCTIONS Model / Modelo 030235 5550 W A TTS 8550 S T AR TING W A TTS Oper ator ’ s Manual Manual del Oper ario Manual No. 200907GS Revision - (08/10/2006) Failure to read and follow the Operator’s Manual and all operating instructions can result in death, bodily injury, and/or property damage.
Briggs & Stratton Power Products Group, LLC 900 North Parkway Jefferson, WI 53549 Copyright © 2006 Briggs & Stratton Power Products Group, LLC. All rights reserved. No part of this material may be reproduced or transmitted in any form by any means without the express written permission of Briggs & Stratton Power Products Group, LLC.
1 T ab le of Contents Safety R ules ..............................................................2 Equipment Description ..........................................................4 Assemb ly ...........................................................
2 BRIGGSandSTRATTON.com SA VE THESE INS TR UCTIONS Safety R ules This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
3 When adjusting or making repairs to your generator: • Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug. When testing for engine spark: • Use approved spark plug tester. • DO NOT check for spark with spark plug removed.
4 BRIGGSandSTRATTON.com A ssembly Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended fuel and oil level is verified. If you have any problems with the assembly of your generator, please call the generator helpline at 1-800-743-4115.
5 5. Install e-ring with pliers, squeezing from top of e-ring to bottom of axle. 6. Repeat steps 4 and 5 to secure second wheel. 7. Tip generator so that engine side is down. 8. Line up holes in support leg ( E ) with holes in generator frame. 9. Attach support leg using 2 capscrews (M8 x 16 mm) ( F ) and 2 hex nuts ( G ).
6 BRIGGSandSTRATTON.com S ystem Gr ound The generator has a system ground that connects the generator frame components to the ground terminals on the AC output receptacles. The system ground is connected to the AC neutral wire (the neutral is bonded to the generator frame).
7 A - 120 Volt AC, 20 Amp, Duplex Receptacles — May be used to supply electrical power for the operation of 120 Volt AC, 20 Amp, single phase, 60 Hz electrical, lighting, appliance, tool, and motor loads.
8 BRIGGSandSTRATTON.com Receptac les 120/240 Volt AC, 30 Amp, Locking Receptacle Use a NEMA L14-30 plug with this receptacle. Connect a 4-wire cord set (A) rated for 250 Volt AC loads at 30 Amps (or greater) (Figure 4). You can use the same 4-wire cord if you plan to run a 120 Volt load.
9 Oper ation Starting the Engine Disconnect all electrical loads from the generator. Use the following start instructions: 1. Make sure unit is on a level surface. IMPORTANT: Failure to start and operate the unit on a level surface will cause the unit not to start or shut down during operation.
10 BRIGGSandSTRATTON.com Connecting Electrical Loads 1. Let engine stabilize and warm up for a few minutes after starting. 2. Plug in and turn on the desired 120 and / or 240 Volt AC, single phase, 60 Hz electrical loads. NOTE: • DO NOT connect 240 Volt loads to the 120 Volt duplex receptacles.
11 Don’t O verload Gener ator Capacity You must make sure your generator can supply enough rated (running) and surge (starting) watts for the items you will power at the same time. Follow these simple steps: 1. Select the items you will power at the same time.
12 BRIGGSandSTRATTON.com General Recommendations Regular maintenance will improve the performance and extend the life of the generator. See any authorized Briggs & Stratton dealer for service. The generator’s warranty does not cover items that have been subjected to operator abuse or negligence.
13 Generat or Maintenance Generator maintenance consists of keeping the unit clean and dry. Operate and store the unit in a clean dry environment where it will not be exposed to excessive dust, dirt, moisture, or any corrosive vapors. Cooling air slots in the generator must not become clogged with snow, leaves, or any other foreign material.
14 BRIGGSandSTRATTON.com SAE 30 : 40 °F and higher (5 °C and higher) is good for all purpose use above 40°F, use below 40°F will cause hard starting. 10W-30 : 0 to 100 °F (-18 to 38 °C) is better for varying temperature conditions. This viscosity improves cold weather starting, but may increase oil consumption above 80ºF (27ºC).
15 Service Air Cleaner Your engine will not run properly and may be damaged if you run it with a dirty air cleaner. Replace the air cleaner every 25 hours of operation or once each year, whichever comes first. Replace more often if operating under dirty or dusty conditions.
16 BRIGGSandSTRATTON.com Clean and inspect the spark arrester as follows: 1. To remove muffler heat shield ( A ) from muffler ( B ), remove four screws that connect guard to muffler bracket (Figure 14). 2. Remove four screws that attach spark arrester screen ( C ).
17 Stor age The generator should be started at least once every seven days and allowed to run at least 30 minutes. If this cannot be done and you must store the unit for more than 30 days, use the following guidelines to prepare it for storage. Generator Storage • Clean the generator as outlined in Cleaning in the Maintenance section.
18 BRIGGSandSTRATTON.com T r oubleshooting Pr oblem Cause Corr ection Engine is running, but no AC output is available. 1. One of the circuit breakers is open. 2. Fault in generator. 3. Poor connection or defective cord set. 4. Connected device is bad.
19 Specif ications Engine T echnical Infor mation This is a single cylinder, overhead valve(OHV), air cooled engine. It is a low emissions engine. In the State of California, Model Series 200000 engines are certified by the California Air Resources Board to meet emissions standards for 250 hours.
20 BRIGGSandSTRATTON.com Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.
21 3. No Charge Repair or replacement of any Warranted Part will be performed at no charge to the owner, including diagnostic labor which leads to the determination that a Warranted Part is defective, if the diagnostic work is performed at an Authorized B&S Service Dealer.
22 BRIGGSandSTRATTON.com BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC PORTABLE GENERATOR OWNER WARRANTY POLICY LIMITED WARRANTY Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the portable generator that is defective in material or workmanship or both.
This page reserved..
Briggs & Stratton Power Products Group, LLC. 900 North Parkway Jefferson, WI 53549 Copyright © 2006 Briggs & Stratton Power Products Group, LLC.
1 T ab la de Conteni do Reglas de segur idad .................................................2 Descripción del equipo ..........................................................4 Montaje ...............................................................
2 BRIGGSandSTRATTON.com CONSER VE ES T A S INS TR UCCIONES Normas de segur idad Éste es el símbolo de alerta de seguridad. Sirve para advertir al usuario de un posible riesgo para su integridad física. Siga todos los mensajes de seguridad que figuren después de este símbolo para evitar lesiones o incluso la muerte.
3 • Cuando arranque el motor, tire lentamente del cable hasta sentir una resistencia y, a continuación, tire rápidamente de él para evitar su retroceso. • NUNCA arranque o pare el motor cuando haya aparatos eléctricos conectados y en funcionamiento.
4 BRIGGSandSTRATTON.com Descripción del equipo Lea atentamente este manual y familiarícese con el generador. Conozca sus aplicaciones, limitaciones y riesgos. Este generador funciona en base a un motor de campo eléctrico giratorio y de corriente alterna (CA).
5 5. Para ello, apriete con unos alicates desde la parte superior de la anilla en “e” hacia la parte inferior del eje. 6. Repita los pasos 4 y 5 para asegurar la segunda rueda. 7. Dele la vuelta al generador de forma que el lado del motor quede abajo.
6 BRIGGSandSTRATTON.com Tierr a del sistema El generador dispone de una conexión a tierra del sistema que conecta los componentes del bastidor a los terminales de tierra de los enchufes hembra de salida de CA. La tierra del sistema está conectada al cable de CA neutro que, a su vez, está conectado al bastidor del generador.
7 Contr oles y caract erísticas del gener ador Lea este Manual del Operario y reglas de seguridad antes de poner en marcha su generador. Compare las ilustraciones con su generador, para familiarizarse con la ubicación de los diversos controles y ajustes.
8 BRIGGSandSTRATTON.com T omas eléctricas Dispositiv o de segur idad de 1 20/240 V , 30 A Use un tapón NEMA L14-30 con este receptáculo. Conecte un juego de cable de 4 alambres (A) , clasificado como 250 Voltios AC a 30 Amps (o mayor) (Figura 4). Usted puede usar el mismo cable de 4-alambres si planea trabajar con una carga de 120 Voltios.
9 Oper ando Encienda el motor Desconecte todas las cargas eléctricas del generador. Use las siguientes instrucciones para encender: 1. Asegúrese de que la unidad está en una superficie plana. IMPORTANTE: Si la unidad no se arranca y utiliza en una superficie plana, se pueden producir problemas de arranque y de parada durante el funcionamiento.
10 BRIGGSandSTRATTON.com Conexión de car gas eléctricas 1. Deje que el motor se estabilice y se caliente por dos minutos después del arranque. 2. Enchúfelo y encienda la carga eléctrica deseada (120 y/o 240 V CA, monofásico, 60 Hz.) IMPORTANTE: • NO conectar cargas de 240 V en las tomas eléctricas dobles.
11 No sobrecar gar el generador Capacidad Debe asegurarse de que su generador puede proveer los suficientes vatios de potencia continua (vatiaje nominal) y vatios de salida para los elementos que desee alimentar al mismo tiempo. Siga estos sencillos pasos: 1.
12 BRIGGSandSTRATTON.com Mantenimient o Plan de mantenimient o Siga los intervalos de horas o de calendario, los que sucedan antes. Si opera en condiciones adversas (señaladas más abajo) es necesario un mantenimiento más frecuente.
13 Mantenimient o del Generador El mantenimiento del generador consiste en conservar la unidad limpia y seca. Opere y almacene la unidad en un ambiente limpio y seco donde no será expuesta al polvo, suciedad, humedad o vapores corrosivos.
14 BRIGGSandSTRATTON.com SAE 30 : 5 º C (40 º F) y superior es adecuado para todo tipo de usos por encima de 5 ºC (40 ºF). El uso por debajo de 5 ºC (40 ºF) provocará dificultades de arranque. 10W-30 : -18 a 38 º C (0 a 100 º F) es mejor en caso de temperatura variable.
15 Servicio del depurador de air e Si se utiliza con un filtro de aire sucio, el motor no funcionará correctamente y puede sufrir daños. Cambie el filtro de aire cada 25 horas de funcionamiento o una vez al año, lo que suceda antes. Haga cambios más frecuentes si trabaja en zonas sucias o donde hay polvo.
16 BRIGGSandSTRATTON.com Limpie e inspeccione el apagachispas de la siguiente manera: 1. Para retirar la protección del silenciador (A) de silenciador (B) , retire los cuatro tornillos que conectan la protección a la ménsula del silenciador (Figura 14).
17 Almacenamiento El generador deberá ser encendido al menos una vez cada siete días y deberá dejarlo funcionar al menos durante 30 minutos. Si no puede hacer esto y debe almacenar la unidad por más de 30 días, siga las siguientes instrucciones para preparar su unidad para almacenamiento.
18 BRIGGSandSTRATTON.com R esolución de prob lemas Problemo Causa Accion El motor está funcionando pero no existe salida de AC disponsible. 1. El interruptor automático de circuito está abierto. 2. Conexión mal o defectuosa del juego de cables. 3.
19 ESPECIFIC A CIONES Información Técnica Sobre el Motor El motor es de uno cilindros, de válvulas en cabeza (OHV), refrigerado por aire y de baja emisión.
20 BRIGGSandSTRATTON.com Briggs & Stratton Corporation (B&S), el California Air Resources Board (CARB, Consejo de recursos de aire de California) y la United States Environmental Protection Agency (U.
21 3. Servicio gratuito La reparación o sustitución de toda pieza garantizada se realizará sin cargo alguno para el propietario, incluido el trabajo de diagnóstico que permita determinar que la pieza garantizada es defectuosa, siempre que se realice en un distribuidor autorizado de servicio B&S.
22 BRIGGSandSTRATTON.com 198189S, Rev. A, 7/14/2006 Esperamos que disfrute de nuestra garantía y le pedimos disculpas por las molestias causadas. Cualquier distribuidor de servicio autorizado puede llevar a cabo reparaciones en garantía.
An important point after buying a device Briggs & Stratton 30235 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Briggs & Stratton 30235 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Briggs & Stratton 30235 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Briggs & Stratton 30235 you will learn all the available features of the product, as well as information on its operation. The information that you get Briggs & Stratton 30235 will certainly help you make a decision on the purchase.
If you already are a holder of Briggs & Stratton 30235, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Briggs & Stratton 30235.
However, one of the most important roles played by the user manual is to help in solving problems with Briggs & Stratton 30235. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Briggs & Stratton 30235 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
