EN
Singer logo
Official user manual

Singer Sewing Machine

60 pages·10.3 MB·Household Appliance·PDF·ENDEFRITNLJA
Singer Sewing Machine
Table of Contents 54 sections “IMPORTANT SAFETY INSTRUCTIONS” · “CAUTION - - · “SAVE THESE INSTRUCTIONS” · F-2 · … ShowHide
Page 1 of the Singer Sewing Machine user manual
Page 1 · click to enlarge
Page 1
Singer Sewing Machine diagram (page 1)
Fig. 1
Page 2 of the Singer Sewing Machine user manual — F-2
Page 2 · click to enlarge
Page 2

“IMPORTANT SAFETY INSTRUCTIONS”

“When using an electrical appliance, basic safety precautions should always be followed, including the following.” “Read all instructions before using this sewing machine.” “DANGER--To reduce the risk of electric shock:”

1. “This sewing machine should never be left unattended when plugged in. Always unplug this sewing machine from the electric

outlet immediately after using and before cleaning.”

“WARNING- To reduce the risk of burns, fire, electric shock, or injury to persons: ”

1. “Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children.” 2. “This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.” 3. “Use this sewing machine only for its intended use as described in this manual. Use only attachments recommended by the

manufacturer as contained in this manual.” 4. “Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped

or damaged, or dropped into water. Return the sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.” 5. “If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.” 6. “Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot

control free from the accumulation of lint, dust, and loose cloth.” 7. “Never drop or insert any object into any opening.” 8. “Indoors use only.” 9. “Do not operate where aerosol (spray) products are being used or where oxygen is being administered.” 10. “To disconnect, turn switch to the off (“0“) position, then remove plug from outlet.” 11. “Switch off or unplug the appliance when leaving it unattended, unplug the appliance before carrying out maintenance or replacing lamps.” 12. “Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.” 13. “Keep fingers away from all moving parts. Special care is required around the sewing machine needle.” 14. “Never sew with a damaged needle plate as this can cause needle to break.” 15. “Do not use bent needles.” 16. “Do not pull or push fabric while stitching. It may deflect the needle causing it to break.” 17. “Switch the sewing machine off (“0”) when making any adjustments in the needle area, such as threading needle, changing needle, threading bobbin, or changing presser foot, etc.” 18. “Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual.” 19. “To avoid electrical shock never put the machine nor the mains cable or mains plug into water or other liquids.” 20. “The LED lamp maximum power is 0.3W, maximum voltage is DC 5V, if the LED lamp is damaged, you should not use the product and send it to the manufacture or service agent to repair or replace at once.” 21. “Caution - to avoid injury: - Unplug the foot controller of the appliance when leaving it unattended: - Unplug the foot controller of the appliance before carrying out any maintenance.”

“CAUTION - -

Moving parts - To reduce risk of injury, switch off before servicing. Close cover before operating

machine.”

“SAVE THESE INSTRUCTIONS”

“This product is for household use, or equivalent.”

FOOT CONTROL (USA & Canada only) Use Model YC-485 EC or Model JF-1000 with this sewing machine.

POLARIZED PLUGS CAUTION (USA & Canada only) This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

This appliance complies with EEC Directive 2004/108/EC covering the electromagnetic compatibility.

Please note that on disposal, this product must be safely recycled in accordance with relevant national legislation relating to electrical/electronic products. If in doubt, please contact your retailer for guidance.

SINGER is the exclusive trademark of The Singer Company Limited S.à r.l. or its Affiliates.

©2012 The Singer Company Limited S.à r.l. or its Affiliates. All rights reserved.

F-2

Page 5 of the Singer Sewing Machine user manual — “IMPORTANT SAFETY INSTRUCTIONS”
Page 5 · click to enlarge
Page 5
Page 5 of the Singer Sewing Machine user manual — “IMPORTANT SAFETY INSTRUCTIONS”
Page 8 of the Singer Sewing Machine user manual — 16 18 17
Page 8 · click to enlarge
Page 8

1. KNOWING YOUR SEWING MACHINE

MACHINE IDENTIFICATION

1. Pre-tension guide 2. Bobbin winding tension disk 3. Thread tension control 4. Threading lever 5. Face cover 6. Thread cutter/holder 7. Extension table (Accessory box) 8. Bobbin winder shaft 9. Bobbin winder stop 10. Reverse stitch button 11. Horizontal spool pin 12. Handle 13. Hand wheel 14. Power/light switch 15. Cord socket 16. Identification plate 17. Extension table release button 18. Presser foot lifter 19. Buttonhole lever 20. Twin thread guide 21. Thread guide 22. Presser foot screw 23. Needle 24. Bobbin cover plate 25. Needle bar 26. Alternate thread cutter 27. Foot release button 28. Needle clamp screw 29. Presser foot 30. Feed dogs 31. Needle plate 32. Bobbin cover release button 33. Power line cord 34. Foot control 35. Instruction manual

16 18 17

33 34 35

Page 10 of the Singer Sewing Machine user manual — 1. KNOWING YOUR SEWING MACHINE
Page 10 · click to enlarge
Page 10
Singer Sewing Machine — 1. KNOWING YOUR SEWING MACHINE diagram (page 10)
Fig. 2

The foot that comes on your sewing machine is called the general purpose foot and will be used for the majority of your sewing.

The satin foot (11) is another very useful foot and should be used for most of your decorative sewing - especially honeycomb , star a etc.

When purchasing additional bobbins, be sure they are Class I5 J.

Page 12 of the Singer Sewing Machine user manual — POWER/LIGHT SWITCH
Page 12 · click to enlarge
Page 12

SETTING UP YOUR MACHINE

Be sure to wipe off any surplus oil from needle plate area before using your machine the first time.

Set power/light switch at “OFF”

Mettez l’interrupteur moteur/ lumière à la position « Fermé »

Power line cord/FOOT CONTROL

Poner el Interruptor de corriente/luz en “OFF”

Connect the plug of the power line cord into the cord socket (1) and your wall outlet (2) as illustrated.

Connect the foot control plug (3) into the machine socket.

Prise du cordon de la machine Conector de la máquina

Pin plug Butée Conector

Power line cord Cordon d’alimentation Cordón de la linea eléctrica

Foot control Rhéostat Control por pedal

Always disconnect the machine from power supply by removing the plug from the electrical outlet.

POWER/LIGHT SWITCH

Your machine will not operate until the power/light switch is turned on. The same switch controls both the power and the light.

Power/light switch “OFF” Interrupteur moteur/lumière « Fermé » (OFF) Interruptor corriente/luz “OFF”

Power/light switch “ON” Interrupteur moteur/lumière « Ouvert » (ON) Interruptor corriente/luz “ON”

When servicing the machine, or changing needles, etc., machine must be disconnected from the power supply.

machine socket

Page 13 of the Singer Sewing Machine user manual — INTERRUPTEUR MOTEUR ET LUMIÈRE
Page 13 · click to enlarge
Page 13

PRÉPARATION DE LA MACHINE

PRÉPARACION DE LA MAQUINA

Avant d’utiliser la machine pour la première fois, assurez-vous de bien essuyer tout surplus d’huile sur et autour de la plaque d’aiguille.

Asegurarse de limpiar cualquier aceite sobrante del área de la placa aguja, antes de usar, por primera vez, la máquina.

CORDON DE LA LINEA ELECTRICA/PEDAL DE CONTROL Conecte el cordón de la linea eléctrica a la máquina (1) y el enchufe a la alimentación de corriente (2) tal como se ve en el dibujo.

CORDON D’ALIMENTATION/RHÉOSTAT

Connectez la fiche du cordon d’alimentation au connecteur de cordon (1) et à la prise murale (2) comme indiqué sur l’illustration.

Conecte el enchufe del control (3) de pedal en el conector de la máquina.

Connectez la fiche du rhéostat (3) au connecteur de la machine.

D é b r a n c h e z t o u j o u r s . L a m a c h i n e d e l’alimentation électrique en retirant la fiche de la prise murale.

Siempre desconecte la máquina de la fuente de alimentación retirando el enchufe del tomacorriente de la pared.

INTERRUPTEUR MOTEUR ET LUMIÈRE

INTERRUPTOR CORRIENTE/LUZ

La machine ne fonctionnera pas avant de mettre l’interrupteur Moteur/Lumière en mode ouvert. Le même interrupteur contrôle l’alimentation et la lumière.

La máquina no funcionará hasta que se conecte el interruptor de corriente/luz. El mismo interruptor controla la corriente y la luz.

Cuando se está utilizando la máquina, o se están cambiando agujas o bobinas, etc., la máquina se debe desconectar de los suministros principales.

Lorsque vous entretenez la machine, où changer une aiguille, etc., assurez-vous de la débrancher de la prise murale.

Page 14 of the Singer Sewing Machine user manual — A
Page 14 · click to enlarge
Page 14

SPOOL PINS

HORIZONTAL SPOOL PIN for normal thread spool Place thread spool on the pin and secure with a spool cap to ensure smooth flow of thread. If the thread spool has a thread retaining slit, it should be placed to the right.

Felt disc Rondelle feutre Disco del pasador carrete

Select the correct spool pin cap according to the type and diameter of spool being used. The diameter of the spool pin cap should always be larger than that of the spool itself.

Vertical spool pin Porte-bobine vertical Pasador de carrete vertical

Thread retaining slit Fente de retenue de fil Ranura de retención de hilo

VERTICAL SPOOL PIN for large thread spool Attach the spool pin. Place the felt disc over it. Place a thread spool on the spool pin.

Spool pin Porte-bobine Pasador carrete

Spool pin cap Chapeau de bobine Tapa del pasador carrete

PRESSER FOOT LIFTER

There are three positions for your presser foot.

1. Lower the presser foot to sew.
2. Raise the lifter to the middle position to insert or remove fabric, and to change presser foot.
3. Lift it to its highest position to insert or to remove thick fabric.

FEED DOG CONTROL

Feed dog control Levier de contrôle des griffes Control de dientes

The feed dogs control the movement of the fabric that is being sewn. They should be raised for all general sewing purposes and lowered for darning, freehand embroidery and monogramming so that you, not the feed dogs, are moving the fabric. You will see the feed dog control when you remove the extension table.

CONVERTING TO FREE-ARM SEWING

Your machine can be used either as a flat-bed or as a free- arm model.

A

With the extension table in position, it provides a large working surface as a standard flat-bed model.

To remove the extension table, hold it firmly with left hand and pull it off to the left while pushing the release button (A) with right hand as shown. To replace, slide the extension table back into place until it clicks.

With the extension table removed the machine converts into a slim free-arm model for sewing children’s clothes, cuffs, trouser legs, and other hard-to-reach places.

Spool Bobine Carrete · Spool Bobine Carrete · Down Basse Abajo

Page 15 of the Singer Sewing Machine user manual — UTILISATION DU BRAS LIBRE
Page 15 · click to enlarge
Page 15

PORTE-BOBINE

PORTA CARRETES

PORTE-BOBINE HORIZONTAL (pour bobine de fil standard) Placez la bobine sur la tige et fixez-y un couvre-fil pour assurer un débit de fil bien régulier. Si la bobine est dotée d’une fente de retenue de fil, elle doit être placée à droite.

PASADOR DE CARRETE HORIZONTAL para carrete de hilo normal Coloque el carrete de hilo en el pasador y asegúrelo con la tapa de pasador para confirmar que el hilo se mueve suavemente. El carrete de hilo tiene una ranura de retención de hilo, que debe quedar hacia la derecha.

Utilisez le chapeau de retenue correspondant au diamètre et au type de bobine utilisée. Le diamètre du chapeau de bobine doit toujours est plus grand que la bobine utilisée.

Seleccione la tapa de pasador de carrete de acuerdo al tipo y diámetro del carrete usado. El diámetro de la tapa de pasador de carrete debe ser siempre mayor que la del mismo carrete.

PORTE-BOBINE VERTICAL (pour bobine de fil plus grosse) Fixez le porte-bobine et la rondelle feutre sur le capot supérieur. Placer la bobine sur le porte-bobine.

PASADOR DE CARRETE VERTICAL para carrete de hilo grande Inserte el portacarrete. Coloque la tapa del portacarrete vertical y el disco de fieltro. Coloque el hilo en el portacarrete.

LEVIER DU PIED PRESSEUR

PALANCA PIE PRENSATELAS

Il y a trois positions pour votre pied presseur.

Su prensatelas tiene tres posiciones.

1. Abaisser le levier pour coudre.
1. Bajar el prensatelas para coser.
2. Soulever le levier en position moyenne pour insérer ou enlever le tissu, et changer le pied.
2. Levantar la palanca a la posición media para insertar o mover la tela.
3. Soulever le levier à sa position la plus haute, pour accommoder les tissus épais.
3. Levantar a la posición más alta para cambiar el prensatelas o para mover el material grueso.

CONTRÔLE DES GRIFFES

CONTROL DE DIENTES

Les griffes contrôle le déplacement du tissu à coudre. Elles doivent être en position relevée pour la couture normal et abaissez pour le piquage et la broderie à mouvement libre, pour que vous et non les griffes, contrôlez l’entraînement du tissu.

Los dientes controlan el movimiento del género que se esta cosiendo. Deben estar elevados durante las operaciones de costura y bajados durante el remendado, bordado con bastidor y colocación de anagramas de modo que sea Vd. y no los dientes quien mueva el género.

Vous pourrez voir le levier de contrôle des griffes lorsque vous retirerez la table de rallonge.

Podrá ver el control del diente impelente cuando quite la mesa de extensión.

UTILISATION DU BRAS LIBRE

CONVERSION PARA LA COSTURA CON BRAZO La máquina se puede utilizar como base plana o una máquina de brazo libre.

Cette machine peut s’utiliser aussi bien à plat ou comme bras libre.

En conservant la table de rallonge en place, vous obtiendrez une plus grande surface de travail.

Con la base de extensión en posición se consigue una superficie de trabajo grande como la de un modelo normal de base plana.

Pour retirer le plateau de rallonge, tenez-le fermement avec la main gauche et tirez-le vers la gauche tout en pressant sur le bouton de déverrouillage (A) avec la main droite comme indiqué. Pour la remettre en place, faites glisser la table de rallonge à sa place jusqu’à ce qu’elle s’enclenche.

Para remover la mesa extensora, sosténgala firmemente con la mano izquierda y sáquela hacia la izquierda mientras presiona con la mano derecha el botón de liberación (A) como se muestra. Para volver a colocarla, deslice la extensión de la cama nuevamente a su lugar hasta que haga clic.

En retirant la table de rallonge, la machine se transforme en bras-libre pour confectionner des vêtements d’enfants, des poignets, des pantalons ainsi que tout autre vêtement difficile d’accès.

Sin la base de extensión instalada la máquina se convierte en un modelo de brazo libre delgado para costura de vestimenta de niños, puños, piernas de pantalones y otros lugares difíciles.

Page 16 of the Singer Sewing Machine user manual — WINDING THE BOBBIN
Page 16 · click to enlarge
Page 16

WINDING THE BOBBIN

Be sure to use Class 15 J bobbins.

1. Place a spool of thread on the spool pin, and secure it with the spool pin cap. Pull the thread out from the spool and place it through thread guides as shown in illustration.
2. Put end of thread through the hole in bobbin as shown.
3. Push bobbin winder shaft to far left position, if it is not already there. Place bobbin onto shaft with end of thread coming from top of bobbin. Push bobbin winder shaft to the right until it clicks. Hold onto end of thread.
4. Start machine. After the bobbin has begun to fill, stop to cut the thread tail. Step on the foot control again to continue to fill the bobbin. The bobbin will automatically stop turning when completely filled. Push shaft to the left to remove bobbin and cut thread.
Page 18 of the Singer Sewing Machine user manual — A B
Page 18 · click to enlarge
Page 18

THREADING THE BOBBIN THREAD

1. Raise the needle to its highest position by rotating the hand wheel counter clockwise.
2. Remove the bobbin cover plate by pushing the release button to the right. Bobbin cover will pop up sufficiently to allow you to remove the cover.
3. Insert the bobbin making sure the bobbin rotates counterclockwise when you pull the thread.
4. Pull thread through the slot (A) and then to the left.

A

5. With a finger held gently on top of the bobbin, pull the thread until it stops in the slot (B). Then pull the thread along the groove on the needle plate until it is snipped with cutter on the top left.
6. Replace the clear bobbin cover plate onto the needle plate.

A B

Cutter Couteau Cortador · Groove Rainure Surco

Page 19 of the Singer Sewing Machine user manual — ENFILAGE DU FIL DE LA CANETTE
Page 19 · click to enlarge
Page 19

ENFILAGE DU FIL DE LA CANETTE

ENHEBRADO DEL HILO DE LA BOBINA

1. Faites tourner le volant vers vous jusqu’à ce que l’aiguille soit dans sa position la plus haute.
1. Eleve la aguja hasta su posición más alta girando el volante en sentido contrario a las manecillas de un reloj.
2. Enlevez le couvercle de la canette en poussant sur le bouton de relâchement du couvercle de la canette. Le couvercle de la canette se désenclenchera suffisamment pour pouvoir le retirez.
2. Retire la tapa de bobina empujando el botón de apertura hacia la derecha. La tapa de la bobina saldrá lo suficiente para permitirle desmontar la cubierta.
3. Insérez la canette, assurez-vous que la canette tourne dans le sens anti-horaire lorsque vous tirez sur le fil.
3. Inserte la bobina asegurándose que la bobina gira hacia la izquierda cuando se tira del hilo.
4. Insérez le fil dans la rainure (A) et tirez le ver la gauche.
4. Lleve el hilo por la abertura (A) y después hacia la izquierda.
5. Appuyez délicatement sur le dessus de la canette avec un doigt, tirez sur le fil jusqu’à ce qu’il s’arrête dans la fente (B). Tirez ensuite le fil le long de la rainure de la plaque d’aiguille jusqu’à ce que le fil se coupe sur le couteau en haut à gauche.
5. Con un dedo colocado suavemente encima de la bobina, tire del hilo hasta que se detenga en la ranura (B). Entonces tirar del hilo a lo largo del surco en la placa de la aguja hasta que se sea agarrado por el cortador en la izquierda superior.
6. Replacez le couvercle de la canette sur la plaque d’aiguille.
6. Vuelva a cerrar la tapa.
Page 20 of the Singer Sewing Machine user manual — IMPORTANT:
Page 20 · click to enlarge
Page 20

THREADING THE TOP THREAD

A

A. Raise the presser foot lifter. Always be sure to raise the

presser foot lifter before threading the top thread. (If the presser foot lifter is not raised, correct thread tension cannot be obtained.)

B. Turn the hand wheel counter clockwise until the needle is

in its highest position.

C. Thread the machine with your left hand while firmly gripping

the thread with your right hand in the following order as illustrated.

B

* Guide the thread through thread guides (1 & 2), and then

pull it down along the groove (3).

* Guide the thread into the thread guide (4).

* Pass the thread through the eye of the needle (5) from

front to back. (See following page for instructions on operation of the Automatic Needle Threader.)

IMPORTANT:

To verify that the machine is threaded properly in the tension discs, do this simple check:

1.) With the presser foot raised, pull the thread towards

the back of the machine. You should detect only a slight resistance and little or no deflection of the needle.

2.) Now lower the presser foot and again pull the thread

towards the the back of the machine. This time you should detect a considerable amount of resistance and much more deflection of the needle. If you do not detect the resistance you have mis-threaded the machine and need to re-thread it.

Page 21 of the Singer Sewing Machine user manual — IMPORTANTE:
Page 21 · click to enlarge
Page 21

ENFILAGE DU FIL SUPÉRIEUR

ENHEBRADO DEL HILO SUPERIOR

A. Soulevez le pied presseur. Assurez-vous toujours que le

A. Levante el prensatelas. Siempre asegúrese de levantar

pied presseur est soulevé avant de faire l’enfilage du fil supérieur. (Si le pied presseur n’est pas soulevé, la tension du fil pourrait être inadéquate.)

el prensatelas antes de bobinar el hilo superior. (Si no se levanta el prensatelas, no se podrá lograr la tensión correcta del hilo.)

B. Faites tourner le volant vers vous jusqu’à ce que l’aiguille

B. Gire el volante en sentido contrario a las manecillas de un

soit dans sa position la plus haute.

reloj hasta que la aguja se encuentre en su posición más alta y el tirahilos quede a la vista.

C. Enfilez le fil de la machine avec votre main gauche tout

en tenant le fil fermement de la main droite, dans l’ordre suivant comme montré dans l’illustration.

C. Enhebre la máquina con su mano izquierda mientras

toma firmemente el hilo con su mano derecha en el orden siguiente tal como está ilustrado.

* Faites passer le fil par les guides de fil (1 & 2), tirez le

ensuite vers le bas dans la rainure (3). * Insérez le fil dans le guide fil (4) * Faites passer le fil par l’orifice de l’aiguille (5) de l’avant

* Guíe el hilo por los guía hilos (1 y 2), y luego tire de él

hacia abajo a lo largo de la ranura (3).

* Guíe el hilo por la guía de hilo (4).

vers l’arrière. (Reportez-vous à la page suivante pour les instructions concernant le fonctionnement de l’enfileur de chas d’aiguille automatique.)

* Pase el hilo a través del ojo de la aguja (5) de adelante

hacia atrás. (Continúe con la página siguiente para las instrucciones sobre el funcionamiento del enhebrador automático de agujas.)

IMPORTANT:

Pour vous assurer que la machine est correctement pourvue de fil dans les disques de tension, effectuez cette simple vérification:

IMPORTANTE:

Para verificar que la máquina ha sido bien enhebrada en los discos de tensión, realice esta verificación sencilla:

1.) Avec le pied presseur relevé, tirez le fil vers l’arrière

1.) Con el pie prensatelas levantado, tire del hilo hacia

de la machine. Vous ne devriez sentir qu’une légère résistance et qu’une légère déflection de l’aiguille.

atrás de la máquina. Deberá detectar solo una ligera resistencia y una pequeña o ninguna deflexión de la aguja.

2.) Ensuite, abaisser le pied presseur et tirez de

nouveau le fil vers l’arrière de la machine. Cette fois, vous devriez sentir une forte résistance et une plus grande déflection de l’aiguille. Si vous ne sentez pas de résistance, le fil a été mal enfilé et vous devez le ré-enfiler.

2.) Ahora vuelva a bajar el pie prensatelas y vuelva

a tirar del hilo hacia atrás de la máquina. En ese momento deberá detectar una cantidad considerable de resistencia y mucha más deflexión de la aguja. Si no detecta la resistencia ha enhebrado mal la máquina y deberá volver a enhebrarla.

Page 22 of the Singer Sewing Machine user manual — A
Page 22 · click to enlarge
Page 22

USING AUTOMATIC NEEDLE THREADER

UTILISATION DE L’ENFILEUR DE CHAS D’AIGUILLE

Be sure to raise the presser foot lifter and raise the needle

to its highest position before threading.

Assurez-vous de soulevez le pied presseur et d'amener

l’aiguille en position haute en tournant le volant vers vous (sens antihoraire) avant d'enfiler la machine.

1. Thread the machine with your left hand while gripping the thread with your right hand. Hook thread to the thread guide on the needle bar and pull it toward you leaving about 4” (10 cm) clear.
1. Enfilez le fil de la machine avec votre main gauche tout en tenant le fil fermement de la main droite. Insérez le fil dans le guide fil de la barre d’aiguille et tirez le vers vous d’environ 10 cm (4 po).
2. Hook thread to the twin thread guide (A and B).
2. Faire passer le fil dans le guide fil double (A et B).
3. Pull thread gently into the thread cutter/holder to cut and hold it in place.
3. Tirez le fil doucement vers le coupeur et reteneur de fil pour le couper et le retenir.

Don’t pull thread with strong force or thread may be pulled off from needle hole after threading.

Ne tirez pas trop fort sur le fil car le fil pourrait ressortir du chas de l'aiguille après avoir été enfilée.

4. Pull down the threading lever to its lowest position until the twin thread guide rotates and stops.
4. Abaissez le levier d’enfilage en position basse jusqu’à ce que le guide de fil double tourne et s’arrête.

Make sure that the guide doesn’t touch fabric, etc. Assurez-vous que le guide ne touche pas au tissu, ect.

5. Release the threading lever and needle will be threaded automatically. If the threading lever should not return to the original position, raise it gently by hand.
5. Relâchez le levier d’enfilage et l’aiguille sera enfilée automatiquement. Si le levier d’enfilage ne retourne pas à ça position d’origine soulevez-le doucement à la main.
6. Pull thread loop away from you.
6. Tirez la boucle du fil vers l’arrière de la machine.

If the needle has not been threaded correctly, re- thread from step 1.

Si l'aiguille n'est pas enfilée correctement, répétez le processus depuis l'étape 1.

machine be set for straight stitch (in center needle position) when using the automatic needle threader.

de régler votre machine au point droit lors de l’utilisation de l’enfileur d’aiguille.

Heavy thread cannot be threaded through fine

Un fil épais ne peut s'insérer dans un aiguille fine.

needle.

N'abaissez pas le levier d'enfilage lorsque la

Don’t lower the threading lever while the machine is

machine est en marche.

in operation or the threading hook may be broken.

2 1 Twin thread guide Guide-fil double Guía doble hilo

Felt disc Disque de feutre Disco de fieltro

Thread guide Guide-fil Guía hilo

Thread cutter/holder Coupeur et reteneur de fil Cortador de hilo

Threading hook Fourchette d'enfilage Gancho del ensartador

A

B

Page 24 of the Singer Sewing Machine user manual — TYPE CALIBRE
Page 24 · click to enlarge
Page 24

NEEDLE, THREAD AND FABRIC CHART

Your fabric will determine the choice of a needle and thread. The following table is a practical guide to needle and thread selection. Always refer to it before a new sewing project. Be sure to use the same size and type of thread in the bobbin as in the top thread supply.

FABRICS THREAD NEEDLES* The fabrics below can be of any fiber: cotton, linen, silk, wool, synthetic, rayon, blends. They are listed as examples of weight. Light- weight

TYPE SIZE

Cotton-wrapped Polyester 100% Polyester

Corduroy Flannel Gabardine Gingham Linen Muslin Wool Crepe Heavy weight

Cotton-wrapped Polyester 100% Polyester Nylon

Bonded Wovens Canvas Coating Denim Duck Sailcloth

Cotton-wrapped Polyester 100% Polyester Heavy Duty

Knits Bonded Knits Double Knit Jersey Tricot

Cotton-wrapped Polyester Polyester Nylon

* For best sewing results, always use a Singer Branded Needle.

TABLEAU DES TISSUS, DU FILS ET DES AIGUILLES

TABLA DE HILO, AGUJA Y MATERIAL

Su material determinará el selecctión de aguja e hilo. Esta tabla es guía práctica para la selección de aguja e hilo. Siempre referirlo antes de coser el material nuevo. Usar el hilo inferior de mismo tamaño y tipo que el hilo superior.

Le choix d’une aiguille et du fil correspondant à votre tissu est très important. Le tableau suivant vous aidera à faire le choix, avant d’entreprendre votre ouvrage. Utilisez, sauf cas particulier, Ie même fil pour I’aiguille et la canette.

MATERIAL HILO AGUJAS* Los materiales siguientes pueden ser de cualquiera fibra: algodón, lino, seda, lana, sintetico, rayón, mezclas. Están listados como ejémplos de peso. Peso ligero

TISSUS FIL AIGUILLES* Les tissus ci-dessous peuvent être de n’importe quelle fibre: coton, lin, soie, laine, synthétique,rayonne, composite. Ils sont énumérés en fonction de leur poids.

TYPE CALIBRE

TIPO TAMAÑO

LÉGERS Batiste Gaze Crêpe

Batista Gasa Crepé Peso medio

Algodón sobre mecha polyester 100% Polyester

Pana Franela Gabardina Guinga Lino Muselina Crepé de lana Medio pesado

Algodón sobre mecha polyester 100% Polyester

MOYENS Velours côtelé Flanelle Gabardine Guigan Toile de lin Mousseline Crêpe de laine LOURDS Tissus apprêtés Toile forte Tissu de manteau Toile de jean Coutil Toile à voiles

Polyester-coton 100% polyester Nylon

Tejido aglomerado Lona Abrigos Denim Loneta Material para Velamen Puntos Punto

Algodón sobre mecha polyester 100% Polyester

Polyester-coton 100%polyester *Fil fort

MAILLES Mailles apprêtés Maille double Jersey Tricot

Algodón sobre mecha polyester Polyester

aglomerado Punto doble Jersey Tricot

* Pour obtenir les meilleurs résultats de couture, utilisez toujours une aiguille de marque Singer.

* Para los mejores resultados de costura, use siempre agujas marca Singer.

Show 49 more labels / short text on this page
Batiste Chiffon Crepe · 2020 red shank · 11/80 orange · band · Medium weight · 2020 red shank · 14/90 blue band · 2020 red shank · 16/100 purple · band · 18/110 yellow · band · 2045 yellow shank · 11/80 orange · band · 14/90 blue band · 16/100 purple · band · Polyester-coton 100% polyester · 2020 tige rouge · 11/80 bague orange · 2020 Vastago · 11/80 banda narranja · rojo 2020 Vastago · 14/90 banda · 2020 tige rouge · 14/90 bague · rojo · azúl · bleue · 2020 Vastago · 16/100 banda púrpula · 2020 tige rouge · 16/100 bague pourpre · rojo · 18/110 bague · jaune · Polyester-coton Polyester Nylon · 2045 tige jaune · 11/80 bague orange · 2045 amarilla · 11/80 banda narranja · rojo · 14/90 bague · 14/90 banda · bleue · azúl · 16/100 bague pourpre · 16/100 banda púrpula
Page 25 of the Singer Sewing Machine user manual — Changement d’aiguille
Page 25 · click to enlarge
Page 25

Always disconnect the machine from power supply by removing the plug from the electrical outlet.

Flat side Côté plat Lado plano

Changing the needle

1. Raise the needle bar to its highest position by turning the hand wheel counter clockwise.
2. Loosen the needle clamp screw by turning it counter clockwise.
3. Remove the needle by pulling it downward.
4. Insert the new needle into the needle clamp with the flat side toward the back.
5. Push the needle up as far as it can go.
6. Tighten the needle clamp screw with the screw driver.

Flat side toward the back

Côté plat orienté vers l’arrière

Lado plano hacia atrás

Helpful Hint: Placing a scrap of fabric under the presser foot and lowering the presser foot makes it easier to change the needle and will preclude dropping the needle into the needle plate slot.

Débranchez toujours. La machine de l’alimentation électrique en retirant la fiche de la prise murale.

Siempre desconecte la máquina de la fuente de alimentación retirando el enchufe del tomacorriente de la pared.

Changement d’aiguille

Cambio de la aguja

1. Relevez la barre d’aiguille à sa position la plus haute en tournant le volant vers vous (sens anti-horaire).
1. Levantar la barra de la aguja a la posición más alta girando el volante en sentido contrario a las manecillas de un reloj.
2. Desserrez la vis du serre-aiguille (sens anti-horaire).
2. Aflojar el tornillo que sujeta la aguja girándolo en sentido contrario a las manecillas de un reloj.
3. Enlever l’aiguille en la tirant vers le bas.
3. Quitar la aguja sacándola hacia abajo.
4. Insérez la nouvelle aiguille dans le serre-aiguille, le côté plat orienté vers l’arrière.
4. Insertar la aguja nueva en la brida porta-aguja con el lado plano hacia la parte posterior.
5. Pousser l’aiguille vers le haut, jusqu’ à la butée.
5. Empujar la aguja lo más arriba posible.
6. Resserrez la vis de l’aiguille à l’aide du tournevis.
6. Apriete el tornillo de sujeción de aguja con el destornillador.

Conseil utile: en plaçant un morceau de tissu sous le pied presseur et en abaissant le pied presseur, vous faciliterez l’opération de remplacement de l’aiguille, et ceci évitera qu’une aiguille ne tombe dans la fente de la plaque d’aiguille.

Needle Aiguille Aguja · Pin Butée Pasador

Page 26 of the Singer Sewing Machine user manual — Levier de verrouillage du pied 2
Page 26 · click to enlarge
Page 26

ADJUSTING TOP THREAD TENSION

Under side Envers Reverso

90% of your sewing will be accomplished with the word “AUTO” exposed on the tension control dial on top of the machine.

Singer Sewing Machine — ADJUSTING TOP THREAD TENSION diagram (page 26)
Fig. 3

Well balanced Correct Bien equilibrada

Helpful Hint: A slight adjustment to a higher number or a lower number may improve sewing appearance.

Top side Endroit Cara

STRAIGHT STITCHING

The correct appearance of your stitching is largely determined by the balanced tension of both top and bobbin threads. The tension is well balanced when these two threads ‘lock’ in the middle of layers of the fabric you are sewing.

If, when you start to sew, you find that the stitching is irregular, you will need to adjust the tension control. Do this, however, only after you have determined that the machine is correctly threaded (see page 18 - 19).

Make all adjustments with presser foot ‘down’.

Top stitch too tight Fil supérieur trop tendu

Top stitch too loose Fil supérieur trop lâche

A balanced tension (identical stitches both top and bottom) is usually only desireable for straight stitch sewing.

Puntada superior demasiado apretada

ZIG ZAG and DECORATIVE SEWING

For zigzag sewing and decorative stitch functions, thread tension should be less than for straight stitch sewing.

You will always obtain a nicer stitch and less puckering when the upper thread appears slightly on the bottom side of your fabric.

BOBBIN TENSION

Decrease tension Diminuer la tension

Increase tension Augmenter la tension

The bobbin tension has been correctly set at the factory, so you do not need to adjust it.

CHANGING PRESSER FOOT

Presser foot lifter Levier du pied presseur Palanca pie prensatelas

Be sure needle is in the up position. Raise presser foot lifter.

1. Push presser foot release button to remove the foot.
2. Place the desired foot on the needle plate aligning the presser foot pin with the foot holder.
3. Lower the presser foot lifter so that the foot holder snaps on the foot.

Levier de verrouillage du pied 2

Boton de desprendimiento prensatelas

Foot holder Support du pied Sujetador prensatelas

Show 5 more labels / short text on this page
Puntada superior · demasiado floja · Disminuir tensión · Aumentar tensión · Foot release button
Page 28 of the Singer Sewing Machine user manual — CONTROL PANEL FUNCTIONS
Page 28 · click to enlarge
Page 28

CONTROL PANEL FUNCTIONS

Number display Affichage du numéro Número de pantalla

LED indicator Témoin DEL Indicador LED

LED indicator Témoin DEL Indicador LED

Stitch width/needle position control Largeur du point/position de l’aiguille sur le point droit Control de posición de aguja/ancho de puntada

Stitch length control Longueur du point Control de largo de puntada

Pattern selection buttons Bouton pour sélectionner les motifs Botones de selección de puntada

Pattern selection buttons Turn on the power switch and the LED indicator on the straight stitch pattern will be lit. At this point you may sew straight stitch.

To select other patterns, push the pattern selection button.

Stitch length and width/needle position controls Your sewing machine will produce most of your stitching requirements at an auto / default stitch length and width. When a pattern is selected, it will automatically sew at default settings of stitch length, width and needle position for that stitch.

Number display shows either stitch length or width depending on the stitch you choose. The LED will light above the stitch length or stitch width control buttons indicating the selected function.

Auto (preprogrammed) default settings are easily determined by pressing the stitch length and width / needle position Control. The LED indicator above the control will change to red at the auto / default position.

Stitch width/needle position control

Once you have determined the auto / default position you can manually change the length, width or straight stitch needle postition according to your preference. At each manual adjustment point, the LED lights in yellow.

Boutons d'ajustement manuel de la longueur du point.

Boutons d'ajustement manuel de la largeur du point et de la position d'aiguille.

The setting you determine on each stitch pattern will continue until you power off the machine.

Control de largo de puntada

Control de posición de aguja/ancho de puntada

Stitch length control

Page 29 of the Singer Sewing Machine user manual — Bouton de sélection des motifs
Page 29 · click to enlarge
Page 29

FONCTIONS DU PANNEAU DE COMMANDE

FUNCIONES DEL PANEL DE CONTROL

Bouton de sélection des motifs

Botones de selección de puntada

Lorsque la machine est mise en fonction, le témoin DEL du point droit s’allume. À ce moment vous pouvez coudre au point droit.

Apague el interruptor y el LED indicador en el patrón de puntada recta se iluminará. En este punto puede coser con puntada recta.

Pour sélectionner d’autre motifs, pressez sur le bouton de sélection du point désiré.

Para seleccionar otros patrones, presione el botón de selección de patrón de puntada.

Bouton d’ajustement de la longueur et de la largeur du point/position d’aiguille. La machine à coudre exécutera un motif sélectionné à une longueur et une largeur préréglée par défaut. Lorsqu’un motif est sélectionné, il sera cousu automatiquement à une longueur, largeur et position d’aiguille pour ce point.

Controles de posición de aguja/Largo y ancho de puntada. Su máquina de coser cumplirá por omisión con la mayoría de sus requerimientos de puntadas en Largo y Ancho de Puntada Automáticos. Cuando se selecciona un patrón, coserá automáticamente en los ajustes por omisión de largo de puntada, ancho y posición de la aguja para dicha puntada.

Le numéro affiché sera soit la longueur ou la largeur du point dépendant du motif choisi. Le témoin DEL s’allumera au- dessus du contrôle de la longueur ou de la largeur du point vous indiquant la fonction sélectionnée.

La pantalla numérica muestra ya sea el largo o ancho de puntada dependiendo de la puntada que elija. El LED se iluminará encima de los botones de control de largo o ancho de puntada indicando la función seleccionada.

Les réglages Automatique (pré-programmer) par défaut sont facilement déterminés en pressant sur les boutons de contrôle de la longueur ou de la largeur du point / position d’aiguille pour le point droit. Le DEL au-dessus des boutons de contrôle vont changés au rouge en position Automatique / par Défaut.

Los ajustes Automáticos (pre-programados) se determinan con facilidad presionando el Control de Posición de la Aguja / Largo Ancho de Puntada. El LED indicador encima del Control cambiará para leer en la Posición Auto / por Omisión.

Una vez que ha determinado la posición Automática/Por Omisión puede cambiar manualmente el largo, ancho o posición de aguja en puntada recta según lo prefiera. En cada punto de ajuste manual, el LED se ilumina de amarillo.

Lorsque vous avez déterminé la position Automatique / par Défaut, vous pouvez changer la longueur, la largeur ou la position d’aiguille pour le point droit dépendant de vos préférences. A chaque ajustement manuel du point, le DEL s’allumera en jaune.

El ajuste que determina en cada patrón de puntada continuará hasta que apague la máquina.

Le réglage que vous avez déterminé sur chacun des motifs restera en vigueur jusqu’à ce que vous éteignez la machine.

Page 30 of the Singer Sewing Machine user manual — Dual purpose reverse/tacking stitch button
Page 30 · click to enlarge
Page 30

REVERSE OPERATION BUTTON

Dual purpose reverse/tacking stitch button

Reverse stitch button Bouton du point de marche arrière interruptor de puntadas hacia atrás

* Reverse stitch function for straight and zigzag stitches ( ) Reverse sewing is carried out while the reverse stitch button

is pushed.

The machine will continue to sew in reverse as long as the

reverse stitch button is pressed.

* Tacking stitch function for tie-off of other stitches ( ) The sewing machine makes 4 tiny tacking stitches to tie

off the sewing on all patterns except straight and zigzag stitches. The position of the tacking stitches will be at the exact spot in the pattern where the reverse/tacking stitch button is pushed.

Page 32 of the Singer Sewing Machine user manual — 2. STARTING TO SEW QUICK REFERENCE TABLE OF STITCH LENGTH AND WIDTH
Page 32 · click to enlarge
Page 32
Singer Sewing Machine — ADJUSTING TOP THREAD TENSION diagram (page 32)
Fig. 4

2. STARTING TO SEW QUICK REFERENCE TABLE OF STITCH LENGTH AND WIDTH

2. POUR COUDRE TABLEAU DE RÉFÉRENCE RAPIDE DES LONGUEURS ET LARGEURS DE POINTS
2. EMPEZER A COSER CUADRO DE REFERENCIA RAPIDA DE LARGO Y ANCHO DE PUNTADA

LEFT - RIGHT GAUCHE - DROIT IZQUIERDA - DERECHA

Page 33 of the Singer Sewing Machine user manual — ADJUSTING TOP THREAD TENSION
Page 33 · click to enlarge
Page 33
Singer Sewing Machine — ADJUSTING TOP THREAD TENSION diagram (page 33)
Fig. 5

BUTTON SEWING POSE DE BOUTONS COSIDO DE BOTÓNES - - 3.0 2.0 - 4.5

Page 34 of the Singer Sewing Machine user manual — KEEPING SEAMS STRAIGHT
Page 34 · click to enlarge
Page 34

STRAIGHT STITCHING

A

B 1

Straight stitch is most frequently used for all types of sewing. Let’s begin by following the steps below.

D

1. SETTINGS Presser foot - General purpose foot Thread tension control - AUTO

E

A. Thread tension control B. Reverse stitch button C. Presser foot lifter D. Stitch length control E. Needle position control

2. Pull both threads under the presser foot toward the back of the machine, leaving about 6” (15cm) clear.
3. Place the fabric under the presser foot and lower the presser foot lifter.
4. Turn the hand wheel counter clockwise until the needle enters the fabric.
5. Start the machine. Guide the fabric gently with your hands. When reaching the edge of the fabric, stop the sewing machine.
6. First turn the handwheel counter clockwise until the needle is at its highest position, then raise the presser foot, draw the fabric to the rear and cut off excess threads with the thread cutter located on the top of face cover as shown.

KEEPING SEAMS STRAIGHT

To keep the seam straight, use one of the numbered guide lines on the needle plate. The numbers indicate distance from the needle at its center position.

The guide line on the bobbin cover plate is 1/4" (6mm) seam guide line which is used for piecing quilt blocks and also for narrow seams, such as those in doll clothes or baby garments.

3/4" (19 mm)

5/8" (16 mm)

1/2" (13 mm)

3/8" ( 9 mm)

1/4" ( 6 mm)

Page 35 of the Singer Sewing Machine user manual — POUR GARDER LA COUTURE DROITE
Page 35 · click to enlarge
Page 35

POINT DROIT

PUNTADA RECTA

Le point droit est le point le plus utilisé pour toute genre de couture. Apprenez à vous servir correctement de la machine, en suivant les étapes ci-dessous.

La puntada recta se usa más frecuentemente para coser todo tipo de costura. Comencemos siguiendo los pasos a continuación.

1. RÉGLAGES Pied presseur - Pied universel Réglage tension du fil supérieur - AUTO
1. AJUSTES Pie prensatelas - Pie universal Control tensión hilo - AUTO

A. Réglage tension du fil supérieur B. Bouton de couture arrière C. Levier du pied presseur D. Contrôle de la longueur du point E. Contrôle de la position de l’aiguille

A. Control tensión hilo B. Botón de puntada de reversa C. Palanca pie prensatelas D. Control longitud puntada E. Control posición de aguja

2. Tirez les deux fils sous le pied presseur vers l’arrière de la machine, en laissant environ 15 cm (6 po) de fil.
2. Tire de ambos hilos debajo del prensatelas hacia atrás de la máquina, dejando una separación de 6 pulg. (15 cm).
3. Placez le tissu sous le pied presseur et abaisser le pied.
3. Colocar la tela debajo del prensatelas y bajar la palanca del prensatelas.
4. Tourner le volant vers vous (sens antihoraire), jusqu’à ce que l’aiguille pénètre dans le tissu.
4. Girar el volante en sentido contrario a las manecillas de un reloj. hasta que la aguja entre en el material.
5. Démarrez la machine. Guidez le tissu légèrement avec les mains. Lorsque vous arrivez au bord du tissu, arrêtez la machine à coudre.
5. Arranque la máquina. Guíe el material suavemente con sus manos. Al llegar al borde del material, pare la máquina de coser.
6. Tournez d’abord le volant vers vous (sens antihoraire), jusqu’à ce que l’aiguille arrive à sa position la plus haute, puis relevez le pied presseur, tirez le tissu vers l’arrière et coupez la longueur de fil excessive au moyen du coupe fil placé au bas de la plaque frontale, comme indiqué sur l’illustration.
6. Primero girar el volante en sentido contrario a las manecillas de un reloj, hasta que la aguja esté en el punto máximo superior. Levantar el pie prensatelas, llevar el tejido hacia atrás y cortar el exceso de hilo con el cortador de hilo que está colocado en la parte inferior del cabezal, como se ilustra.

POUR GARDER LA COUTURE DROITE

MANTENIENDO LA PUNTADA DERECHA

Pour piquer une ligne droite, utilisez les guides sur la plaque d’aiguille. Le numéro indiqué est la distance entre l’aiguille au centre et la ligne sur la plaque.

Para mantener la puntada derecha, utilice una de las líneas guía numeradas en la placa aguja. Los números indican la distancia desde la aguja hacia la posición central de la misma.

La ligne guide sur la plaque couvre canette est à une distance de 6 mm (1/4 po) de l’aiguille au centre et peut-être utilisé pour l’assemblage de pièces de matelassage et aussi pour les ourlets étroits tel que pour les tissus de poupée ou des vêtements de bébé.

La línea guía en la cubierta de la bobina tiene 1/4" (6mm) de distancia de la línea guía central y se utiliza comúnmente como guía para juntar bloques de tela para “Quilting” y para costuras muy delgadas tales como aquellas en vestidos de muñecas o en prendas de bebé.

Page 36 of the Singer Sewing Machine user manual — HAND-LOOK QUILT STITCH
Page 36 · click to enlarge
Page 36

INSERTING ZIPPERS AND PIPING

Use zipper foot to sew to the right or left of the zipper or to sew close to the cording.

Needle to left of foot Needle to right of foot

Aiguille à gauche du pied presseur

Aiguille à droite du pied presseur

Aguja a la izquierda del prensatelas

Aguja a la derecha del prensatelas

Singer Sewing Machine — INSERTING ZIPPERS AND PIPING diagram (page 36)
Fig. 6

INSERTING ZIPPERS To sew down the right side, attach left side of zipper foot to presser foot holder so that the needle passes through the opening on the left side of the foot.

To sew down the left side, attach right side of foot to foot holder.

PIPING Create a piping by covering a filler cord with a bias strip of fabric.

Attach the right side of the zipper foot to the foot holder so that the needle passes through the right side of the zipper foot.

Baste the seam allowances together, enclosing the filler cord, forming a seam tape for the piping. Then, pin or tack to the main fabric piece for sewing.

Helpful hint: Slight adjusting of the needle position to sew closer to the piping may be accomplished with the stitch width control.

HAND-LOOK QUILT STITCH

This stitch is designed to look like hand sewing for topstitching and quilting.

Singer Sewing Machine — HAND-LOOK QUILT STITCH diagram (page 36)
Fig. 7
1. Thread bobbin with desired top stitching color. When sewing, the machine will pull this thread to the top.
2. Thread machine with invisible or lightweight thread that matches your fabric. This thread should not show.
3. Increase thread tension a little at a time and continue until you acheive the desired appearance.
4. Start to sew.
Page 38 of the Singer Sewing Machine user manual — PLACEMENT OF PATTERNS
Page 38 · click to enlarge
Page 38

ZIGZAG STITCHING

Under side Côté de dessous Reverso

Singer Sewing Machine — ZIGZAG STITCHING diagram (page 38)
Fig. 8

SETTINGS :Presser foot - General Purpose Foot :Thread tension control - AUTO

The top thread may appear on the bottom depending on the thread, fabric, type of stitch and sewing speed, but the bobbin thread must never appear on the top of the fabric.

If bobbin thread is pulling to the top or you are experiencing puckering, slightly reduce the tension with the thread tension control.

Top side Côté de dessus Cara

ADJUSTING STITCH WIDTH AND LENGTH

Dark grey box indicates the auto/default value set automatically when the pattern is selected. For the zigzag pattern the stitch length is 2 mm and the stitch width is 5 mm.

STITCH WIDTH LARGEUR DU POINT

ANCHO PUNTADA

mm 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

The light grey boxes indicate all the possible personal preference options available to set manually.

LONGUEUR DU POINT

STITCH LENGTH

LARGO PUNTADA

SATIN STITCH

Singer Sewing Machine — SATIN STITCH diagram (page 38)
Fig. 9

This is a closely spaced zig zag stitch used for appliqué, bar tacking, etc. Slightly loosen the top thread tension and manually adjust the stitch length between 0.5 and 2.0 for satin stitching.

Use a backing of stabilizer for lightweight fabrics to avoid puckering.

PLACEMENT OF PATTERNS

Center position Position centrale Aguja posicionada en el centro

Stitch width of pattern increases from center needle position as illustrated.

Page 39 of the Singer Sewing Machine user manual — POSITIONNEMENT DES MOTIFS
Page 39 · click to enlarge
Page 39

POINT ZIGZAG

PUNTADA ZIG-ZAG

RÉGLAGES :Pied presseur - Pied universel :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Pie universal :Control tensión hilo - AUTO

Le fil supérieur peut paraître sur l’envers, en fonction du fil, du tissu et de la vitesse de couture, mais le fil de la canette ne doit jamais paraître sur l’endroit.

El hilo superior puede aparecer en la parte inferior, según el hilo, tejido, tipo de puntada y velocidad de costura, pero el hilo de la bobina nunca deberá aparecer en la parte superior del tejido.

Si le fil de la canette tire vers le haut ou si des fronces se produisent, réduisez légèrement la tension à l’aide de la commande de réglage de la tension du fil supérieure.

Si el hilo de la bobina se jala hacia arriba o si tiene problemas con la formación de arrugas, reduzca ligeramente la tensión con el control de tensión de hilo.

RÉGLAGE DE LA LARGEUR ET DE LA LONGUEUR DU POINT

AJUSTE DEL ANCHO Y LARGO DE PUNTADA

Une case gris foncé indique la valeur automatique/par défaut réglée automatiquement lors de la sélection du motif. Pour le motif zigzag, la longueur du point est de 2 mm et la largeur du point est de 5 mm.

La casilla gris oscuro indica el valor automático/por defecto ajustado automáticamente cuando se selecciona el patrón. Para el patrón de zigzag el largo de puntada es 2 mm y el ancho de puntada es 5 mm.

La case gris clair indique toutes les options de préférences personnelles disponibles pouvant être réglées manuellement.

La casilla gris clara indica todas las opciones de preferencia personal disponibles para ajustar manualmente.

POINT BOURDON

PUNTADA DE RELLENO

Ceci est un point très rapproché pour un appliqué et une bride, etc. Lorsque vous utilisez ce point, pensez à diminuer la tension supérieure. Réglez la longueur du point entre 0.5 et 2.0. pour le point bourdon.

Esta es una puntada de zigzag muy junta, usada para aplicaciones, atacados, etc. Para la puntada de relleno aflojar ligeramente la tensión del hilo superior.

Para evitar el arrugado en telas delgadas, use entretela.

Utilisez un entoilage pour éviter les fronces.

POSITIONNEMENT DES MOTIFS

UBICACION DE LOS PATRONES

La largeur du point augmente par rapport à la position de l’aiguille centrale; pour créer un centre effilé comme illustré.

El ancho de los patrones aumenta desde la posición central de la aguja como se muestra.

Page 40 of the Singer Sewing Machine user manual — MULTI-STITCH ZIGZAG
Page 40 · click to enlarge
Page 40

BLINDHEM STITCH

Medium to heavyweight fabric Tissus moyens et lourds Material de peso medio a pesado

The blindhem stitch is primarily used for hemming curtains, trousers, skirts, etc.

SettingsPresser foot - Blind stitch foot : Thread Tension Control: AUTO
Singer Sewing Machine — BLINDHEM STITCH diagram (page 40)
Fig. 10
Singer Sewing Machine — BLINDHEM STITCH diagram (page 40)
Fig. 11

- Regular blind stitch for normal woven fabrics

Under side Envers Reverso

- Elastic blind stitch for soft, stretchable fabrics

Under side Envers Reverso

Fine fabric Tissus fins Material fino

1. With matching thread finish the raw edge. On fine fabric, turn up and press a small ½” or less hem. On medium to heavyweight fabrics overcast the fabric’s raw edge.
2. Now fold the fabric as illustrated with the wrong side up.

Under side Envers Reverso

Under side Envers Reverso

Singer Sewing Machine — - Elastic blind stitch for soft, stretchable fabrics diagram (page 40)
Fig. 12 · - Elastic blind stitch for soft, stretchable fabrics
3. Place the fabric under the foot. Turn the handwheel counter clockwise by hand until the needle swings fully to the left. It should just pierce the fold of the fabric. If it does not, adjust the guide (B) on the blindhem foot (A) so that the needle just pierces the fabric fold and the guide just rests against the fold.

B

Singer Sewing Machine — B diagram (page 40)
Fig. 13

A

Sew slowly, guiding the fabric carefully along the edge of the guide.

Singer Sewing Machine — A diagram (page 40)
Fig. 14
4. When completed, the stitching is almost invisible on the right side of the fabric.

Top side Endroit Cara

MULTI-STITCH ZIGZAG

Singer Sewing Machine — MULTI-STITCH ZIGZAG diagram (page 40)
Fig. 15

SETTINGS :Presser foot - General purpose foot :Thread tension control - AUTO

This is a strong stitch because as its name implies, it makes three short stitches where the normal zig-zag makes only one.

For this reason it is highly recommended for overcasting all types of fabrics.

It is also ideal for bartacks, mending tears, patching, sewing towelling, and attaching flat elastic.

Page 41 of the Singer Sewing Machine user manual — ZIGZAG MULTI-POINT
Page 41 · click to enlarge
Page 41

POINT INVISIBLE

PUNTADA INVISIBLE

RÉGLAGES :Pied presseur - Pied ourlet invisible :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Prensatelas de puntada invisible :Control tensión hilo - AUTO

- Point ourlet invisible régulier pour tissu tissé

Puntada invisible regular para las telas normales

- Point ourlet invisible pour les tissus extensibles

Puntada invisible super elástico para las telas suves, elástico

1. Avec un fil assorti, cousez le rebord coupé. Sur un tissu léger, faites un rebord d’environ 1.3 cm (1/2 po) ou moins et repassez. Sur un tissus moyen ou épais, surjetez le rebord coupé.
1. Con hilo del mismo color orillar la tela. Sobre el tejido delgado, voltée y haga un dobladillo de 1/2” o menos. En telas de peso medio o completo sobrehile el borde de la tela.
2. Maintenant, pliez le tissu comme indiqué dans l’illustration, l’envers tourné vers le haut.
2. Ahora doble el material tal como está ilustrado con el reverso hacia arriba.
3. Placez le tissu sous le pied. Faites tourner le volant à la main vers vous (sens antihoraire) jusqu’à ce que l’aiguille se déplace complètement vers la gauche. Elle ne devrait percer que le repli du tissu.
3. Coloque el material debajo del pie. Gire el volante en sentido contrario a las manecillas de un reloj a mano hasta que la aguja se mueva completamente hacia la izquierda. Deberá solo atravesar el pliegue del material. De lo contrario, ajuste la guía (B) en el pie de puntada invisible (A) de manera que la aguja solo atraviese el pliegue del material y la guía solo descanse contra el pliegue.

Effectuez la couture lentement, tout en guidant soigneusement le tissu le long du bord du guide.

Cosa lentamente, guiando el material cuidadosamente a lo largo del borde de la guía.

4. Lorsque l’ourlet est terminé, les points sont presque invisibles sur l’endroit du tissu.
4. Una vez terminado, los puntos son casi invisibles sobre el lado derecho del material.

ZIGZAG MULTI-POINT

ZIG-ZAG DE TRES PUNTADAS

RÉGLAGES :Pied presseur - Pied universel :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Pie universal :Control tensión hilo - AUTO

Comme son nom l’indique, le point est solide, car il fait trois points courts là où le zigzag normal n’en fait seulement qu’un.

Esta es una puntada fuerte, ya que como su nombre implica, realiza tres puntadas cortas donde el zig-zag normal sólo realiza una.

Pour cette raison, on le recommande pour surjeter tous les types de tissus.

Por esta razón es muy recomendada para el sobrehilado de todo tipo de tejidos.

Il est aussi idéal pour les points d’arrêt, le reprisage et pour la pose d’élastique plat.

También es ideal para zurcir desgarrones, parches, coser toallas, remiendos y aplicación de elástico plano.

Page 42 of the Singer Sewing Machine user manual — OVEREDGE STITCH
Page 42 · click to enlarge
Page 42

STRETCH AND DECORATIVE STITCHES

SETTINGS :Presser foot - General purpose foot or satin stitch foot :Thread tension control - AUTO

Stretch stitches are mainly for use on knit, or stretchable fabrics, but can also be used on woven fabrics.

STRAIGHT STRETCH STITCH

Straight stretch stitch is far stronger than an ordinary straight stitch because it locks three times - forwards, backwards and forwards.

Singer Sewing Machine — STRAIGHT STRETCH STITCH diagram (page 42)
Fig. 16

It is particularly suitable for reinforcing the seams of sportswear in stretch and non-stretch fabrics, and for curved seams which take a lot of strain.

Use this stitch also to top-stitch lapels, collars and cuffs to give a professional finish to your garments.

RIC-RAC STITCH

Singer Sewing Machine — RIC-RAC STITCH diagram (page 42)
Fig. 17

Ric-rac is primarily used for a decorative top-stitch. It is ideal for edging neck-bands, armholes, sleeves and hems. When manually adjusted to a very narrow width, it can also be used for sewing high-stress seams.

HONEYCOMB STITCH

The honeycomb stitch is ideal for smocking and useful for overcasting and attaching elastic and stretch lace.

Singer Sewing Machine — HONEYCOMB STITCH diagram (page 42)
Fig. 18
1. Make several rows of gathers across the fabric that you wish to smock.
2. With a narrow strip of fabric directly under the line of gathering, stitch over the gathers. The design will be a series of small diamonds.

OVEREDGE STITCH

This is a similar stitch used by the garment industry in making sportswear - it sews and finishes the seam in one operation.

It’s very effective for use in repairing raw or worn edges of garments.

Page 43 of the Singer Sewing Machine user manual — POINT SURJET EXTENSIBLE
Page 43 · click to enlarge
Page 43

POINT DÉCORATIFS ET POINTS EXTENSIBLES

PUNTADAS ELASTICAS Y DECORATIVAS

AJUSTES :Pie prensatelas - Pie universal o para coser en satén :Control tensión hilo - AUTO

RÉGLAGES :Pied presseur - Pied universel ou point bourdon :Réglage de la tension du fil supérieur - AUTO

Las puntadas elásticas se utilizan principalmente en materiales de punto o materiales elásticos, pero también se puede usar en materiales corrientes.

Les points extensible sont utilisés surtout sur les tricots et les tissus extensibles, mais peuvent tout aussi bien êtres utilisées sur des tissus tissés.

POINT DROIT EXTENSIBLE

PUNTADA RECTA TRIPLE

Ce point est beaucoup plus solide que le point ordinaire, vu qu’il s’exécute en trois fois, une fois en avant, une fois en arrière et encore une fois en avant.

La puntada recta triple es mucho más fuerte que la puntada recta corriente, ya que entrelaza tres veces–hacia adelante, hacia atrás y hacia adelante.

Il est particulièrement utile pour renforcer les coutures sur les tissus de sport extensible ou non, et pour les coutures en courbes qui demandent beaucoup de force.

Es particularmente adecuada para reforzar las costuras de prendas deportivas de tejidos elásticos y no elásticos y para costuras curvas que requieren una gran resistencia.

Utilisez aussi ce point spécial, il convient particulièrement bien pour surpiquer les revers, les cols, les poignets.

Utilizar también esta puntada para sobrecoser solapas redondeadas, cuellos y puños, ya que proporciona un acabado profesional a las prendas.

POINT RIC-RAC

PUNTADA RIC RAC

Le Ric-Rac est principalement utilisé pour la couture décorative. Il est idéal pour les rebords des collets, des poignets, des manches et des ourlets. Lorsque la largeur est ajustée manuellement à un point très étroit, il peut être utilisé pour faire des coutures résistantes.

El ric rac es un método rápido de acabado de un borde y proporciona una sobrecostura decorativa en una operación. Es ideal para escotes, sisas, mangas y dobladillos.

NID D’ABEILLE

PUNTADA PANAL

Le point nid d’abeille est idéal pour la couture de smocks et utile pour surfiler et coudre de la dentelle élastique et extensible.

La puntada panal es ideal para adornar con nido de abeja y es útil para sobrehilado y colocar cintas elásticas.

1. Realiza una línea recta de fruncidos a través del tejido que se desea adornar con nido de abeja.
1. Pour la couture de smocks, débuter en cousant plusieurs rangs de fronce sur le tissu sur lequel vous voulez faire du smock.
2. Con una tira estrecha de tejido, directamente debajo de la línea de fruncido, coser sobre los fruncidos. El diseño será una serie de diamantes pequeños.
2. Coupez une pièce de tissus d’entoilage (comme un organdi) et placez-le sous la section froncée, coudre plusieurs rangs de points nids d’abeilles sur les fronces pour les tenir en place.

POINT SURJET EXTENSIBLE

PUNTADA SOBRE-BORDE

Point extensible spécial pour assembler et surfiler en une seule opération. Il est utilisé dans l’industrie de la confection, surtout pour les vêtements de sport.

Este es el mismo tipo de puntada usada por la industria de la confección en la fabricación de prendas. Se forma y acaba la costura en una operación.

C’est très efficace pour réparer des coutures défaites ou des vêtements endommagés.

Es muy efectiva para el uso en la reparación de bordes gastados de prendas usadas.

Page 44 of the Singer Sewing Machine user manual — SLANT OVEREDGE STITCH
Page 44 · click to enlarge
Page 44

FEATHER STITCH

The pleasing appearance of this stitch enables it to be used for top stitching, or attaching lace or inset panels when making lingerie.

It is also ideal for quilting applications and joining fabrics.

PIN STITCH

The pin stitch is a traditional stitch pattern used for picot-like edges and for appliqué work.

BLANKET STITCH

The blanket stitch is traditionally a hand-sewn stitch used to put bindings on blankets. This multi-purpose stitch can also be used for attaching fringe, attaching edgings, couching, appliqué and drawn thread hemstitching.

LADDER STITCH

The ladder stitch is primarily used for drawn thread hemstitching. It can also be used for sewing over thin tape in an opposite or same color. Place the stitch in the center and a special effect will be obtained for decoration.

Another use for the ladder stitch is couching over narrow ribbon, yarn or elastic.

For drawn thread work, choose a coarse linen type fabric and after sewing draw the thread out within the ladder for an open airy appearance.

SLANT OVEREDGE STITCH

Seams and overcasts in one operation to produce a narrow, supple seam, particularly suited to swimwear, sportswear, T-shirts, babywear in stretch nylon, stretch toweling, jersey and cotton jersey.

Page 46 of the Singer Sewing Machine user manual — SEWING ON A BUTTON
Page 46 · click to enlarge
Page 46

ENTREDEUX STITCH

Useful for decorative stitching on borders and for use in heirloom sewing. The Entredeux stitch is most often sewn with a Wing Needle (Singer Style 2040) to create holes in the stitch pattern.

Helpful hint: A slight + adjustment of the tension will increase the size of the hole when using a wing needle.

DECORATIVE PATTERNS

SETTINGS :Presser foot - Satin stitch foot :Thread tension control - AUTO

* Always practice on a scrap of the actual fabric from your

project.

* Before starting to sew, check that there is enough thread

wound onto the bobbin to make sure that the thread will not run out during sewing.

* Slightly loosen top thread tension.

Helpful hint: For a more pleasing appearance experiment with a slightly lower (-) tension setting.

IDEAS ON DESIGN STITCHING

Singer Sewing Machine — IDEAS ON DESIGN STITCHING diagram (page 46)
Fig. 19

Crescent pattern on collar

This is an ideal decorative stitch for the sleeves and collars of ladies’ and children’s clothes, and also for table linen edges.

When using this stitch pattern for table linen edges, first sew the stitch and then trim the edge of the fabric along the edge of the stitch. Be careful not to cut the stitch at this time.

CONTINUOUS PATTERNS

SETTINGS :Presser foot - General purpose foot or Satin stitch foot :Thread tension control - AUTO

These are the optimum patterns for sewing continuous patterns often seen on borders or hems of garments and home decorating projects. Use whichever patterns suit your preference.

SEWING ON A BUTTON

SETTINGS :Presser foot - General purpose foot :Feed dog control -

Position your fabric and button under the presser foot. Lower presser foot. Turn the handwheel to make sure needle clears both left and right openings of button. Adjust width if required. Sew 10 stitches.

If a button shank is required, place a darning needle on top of the button and sew over top of it as illustrated.

Singer Sewing Machine — SEWING ON A BUTTON diagram (page 46)
Fig. 20

Helpful hint: To secure thread, pull both threads to the backside of the fabric and tie together.

Page 47 of the Singer Sewing Machine user manual — POSE DE BOUTONS
Page 47 · click to enlarge
Page 47

POINT ENTREDEUX

PUNTADA “ENTREDOS”

Utile pour la couture décorative de bordures et pour une couture à l’ancienne. Le point entredeux est le plus souvent cousu à l’aide d’une aiguille sabre (Style SINGER 2040) pour créer des trous dans le motif du point.

Útil para puntadas decorativas de bordes y para usar en costuras antiguas. La puntada “Entre dos” es más comúnmente usada con una aguja “de ala” (Singer estilo 2040) para crear agujeros en el patrón de costura.

Conseil utile: un léger ajustement + de la tension augmente la taille du trou lorsqu’une aiguille sabre est utilisée.

POINTS DÉCORATIFS

DISEÑOS DE BORDADOS DECORATIVOS

RÉGLAGES :Pied presseur - Pied point bourdon :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Pie para coser en satén :Control tensión hilo - AUTO

* Vous devriez effectuer un essai sur une pièce du même

* Puede realizar una costura de prueba en un recorte de material para verificar el patrón a usar.

tissu à coudre pour vérifier le résultat.

* Avant de débuter une couture, vérifier qu’il y a assez de fil

* Antes de comenzar la costura, verifique que haya suficiente hilo enrollado en el carrete para asegurarse que no se quedará sin hilo durante la costura.

enroulé sur la bobine, afin de ne pas manquer de fil lors de la couture.

* Diminuez légèrement la tension du fil supérieur.

* Afloje liberamente la tensión del hilo superior.

Conseil utile: pour une meilleure apparence faite des essais en diminuant (-) légèrement la tension du fil supérieur.

IDÉES SUR LES POINTS DÉCORATIFS

TIPOS DE PUNTADAS DECORATIVAS

Point croissant cousu sur un collet

Creciente de ondas de cuello

C’est un point décoratif idéal pour les manches et les collets des vêtements féminin et d’enfant et aussi pour la finition des napperons en tissu.

Esto es ideal para puntadas decorativas de mangas y cuellos de vestimenta de damas y niños, y también para bordes tableados.

Avant de débuter une couture sur les napperons en tissu, cousez en premier le motif et ensuite découpez le rebord du tissu en suivant le rebord du motif. Assurez-vous de ne pas coupez le fil du motif.

Cuando se usa este patrón de puntada para bordes tableados, primero se debe coser la puntada y luego cortar el borde del material a lo largo del borde de la puntada. Tenga cuidado de no cortar la costura.

MOTIFS EN CONTINUS

PATRONES CONTINUOS

RÉGLAGES :Pied presseur - Pied universel ou point bourdon :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Pie universal o para coser en satén :Control tensión hilo - AUTO

Ceux-ci sont les motifs optimums pour coudre en continus, souvent vus sur les bordures ou les ourlets de vêtements et sur des projets de décoration intérieure. Utilisez les motifs selon vos préférences.

Estos son los patrones ideales para costura de patrones continuos. Use cualquiera de los patrones de acuerdo a su preferencia.

POSE DE BOUTONS

COSIDO DE BOTONES

RÉGLAGES :Pied presseur - Pied universel :Abaisse-griffes d’entraînement -

AJUSTES :Pie prensatelas - Pie universal :Control de dientes -

Placez le tissu et le bouton sous le pied presseur. Abaissez le pied. Tournez le volant pour vous assurez que l’aiguille passe nettement dans les trous gauche et droit du bouton (régler la largeur du point en fonction du bouton) et coudre le bouton lentement en utilisant approximativement 10 points.

Coloque el botón en la posición deseada, baje el prensatelas, Gire el volante para comprobar que la aguja entra limpiamente en los agujeros derecho e izquierdo de botón (ajuste el ancho de la puntada) y cosa lentamente el botón con unas 10 puntadas.

Si une tige de maintien est requise, placez une aiguille de reprisage sur la partie supérieure du bouton et coudre.

Conseil utile: pour fixer le fil, tirez les deux fils vers l’arrière du tissu et liez-les ensemble.

Page 48 of the Singer Sewing Machine user manual — (C) (C)
Page 48 · click to enlarge
Page 48

SEWING A BUTTONHOLE

tab B Languette B Lengüeta B

USING BUTTONHOLE FOOT

tab A Languette A Lengüeta A

Your machine offers you two different widths of bartack buttonholes sewn by a system that measures the size of the button and calculates the size buttonhole required. All of this is done in one easy step.

PROCEDURE

* Use an interfacing in the area of the garment where

buttonholes are placed. Stabilizer or regular interfacing can be used.

* Make a practice buttonhole on a scrap of the actual fabric

from your project. Then try the buttonhole with your button.

1. Select one of buttonhole patterns.

(C)

2. Replace the presser foot with the buttonhole foot. (Refer to “Changing presser foot” on page 24 - 25.)
3. Insert the button into the buttonhole foot. (Refer to “Using buttonhole foot” above.)

(A) (B)

Buttonhole foot Pied boutonnière Prensatelas de ojales

4. Lower the buttonhole lever (C) so that it drops down vertically between the stoppers (A) and (B).

(C) (C)

(C)

5. Carefully mark the position of buttonhole on your garment.
6. Place the fabric under the foot. Pull out the bobbin thread underneath the fabric to a length of about 4 inches to the rear.
7. Align the buttonhole mark on the fabric with the mark on the buttonhole foot, and then lower the buttonhole foot.

Fabric marking Marque du tissu Marca de material

8. While holding the top thread, start the machine.

mark Marque Marca

Page 49 of the Singer Sewing Machine user manual — PROCÉDURE
Page 49 · click to enlarge
Page 49

CONFECTION DES BOUTONNIÈRES

CONFECCION DE OJALES

BOUTONNIÈRE AUTOMATIQUE

USO DEL PIE DE OJALADOR

La machine à coudre vous offre deux différentes largeurs de boutonnières à brides; à oeillet et boutonnières arrondies cousues au moyen d’un système mesurant la taille du bouton et qui calcule la taille de la boutonnière. Tout ceci s’effectue en une simple étape.

Su máquina de coser le ofrece dos anchos de ojales cosidos por un sistema que mide el tamaño del botón y calcula el tamaño del ojal necesario. Todo esto es realizado en solo un paso fácil.

PROCÉDURE

PROCEDIMIENTO

* Utilisez un entoilage dans la partie du vêtement où les

* Practique haciendo un ojal en un pedazo de material del

boutonnières doivent être placées.

* Faites une boutonnière d’essai sur un échantillon du tissu

que vous utilisez. Essayez ensuite la boutonnière avec le bouton choisi.

* Use una entretela en el área de la vestimenta donde se

van a hacer los ojales. Se puede usar papel tisú o entretela normal. Después de coser el ojal retire el papel.

1. Sélectionnez l’un des motifs de boutonnières.
1. Seleccione uno de los patrones de ojales.
2. Remplacez le pied presseur par le pied boutonnière. (Reportez-vous à la section "Remplacement du pied presseur" à la page 24 - 25.)
2. Cambie el prensatelas por el pie ojalador. (Consulte “Cambio del pie prensatelas” en la página 24 - 25.)
3. Introduisez le bouton dans le pied boutonnière. (Reportezvous à la section "Utilisation du pied boutonnière" ci-haut.)
3. Inserte el botón en el pie ojalador. (Consulte “Uso del pie ojalador” arriba.)
4. Abaissez le levier de boutonnière (C) de manière qu’il s’abaisse verticalement entre les butées (A) et (B).
4. Ajuste la palanca de ojales (C) de manera que baje verticalmente entre los topes (A) y (B).
5. Marquez soigneusement la position de la boutonnière sur le vêtement.
5. Marque cuidadosamente la posición del ojal en la vestimenta.
6. Placez le tissu sous le pied. Tirez le fil de la bobine sous le tissu sur une longueur d’environ 10 cm (4 po) vers l’arrière.
6. Coloque el material debajo del pie. Tire del hilo de la bobina debajo del material a un largo de aproximadamente 10 cm hacia atrás.
7. Alignez la marque de la boutonnière du tissu sur la marque du pied presseur, puis abaissez le pied boutonnière.
7. Alinee la marca del ojal en el material con la marca en el pie ojalador, y luego baje el pie ojalador.
8. Tout en tenant le fil supérieur, démarrez la machine.
8. Mientras sostiene el hilo superior, haga funcionar la máquina.
Page 50 of the Singer Sewing Machine user manual — ADJUSTING TOP THREAD TENSION
Page 50 · click to enlarge
Page 50
Singer Sewing Machine — ADJUSTING TOP THREAD TENSION diagram (page 50)
Fig. 21

* Sewing will be completed automatically in the following order.

Buttonhole foot alignment position Positionnement du pied boutonnière Posición de alineación del pie ojalador

9. When sewing is finished, use a buttonhole opener/seam ripper to open up the fabric in the center of the buttonhole. Be careful not to cut any of the stitching.

Hook filler cord (crochet thread or buttonhole twist) over the spur and pull both ends of the cord forward under the foot and tie off the cord as shown in the illustration.

Sew buttonhole so that zigzag stitches cover the cord.

When completed, release the cord from foot, pull cords to release slack and snip off extra length.

Page 52 of the Singer Sewing Machine user manual — (3) (4)
Page 52 · click to enlarge
Page 52

3. CARING FOR YOUR MACHINE

CLEANING HOOK AREA AND FEED DOGS

Always disconnect the machine from power supply by removing the plug from the electrical outlet.

CAUTION

To ensure the best possible operation of your machine, it is necessary to keep the essential parts clean at all times.

(1)

1. Raise the needle to its highest position.
2. Remove two screws on the needle plate (1) and slide the needle plate toward you as illustrated for removal.
3. Remove the bobbin case (2).

(2)

4. Clean the feed dogs and hook area with the lint brush. Put one drop of sewing machine oil on the hook race as indicated by the arrows. (A, B)

(A)

(B)

5. Replace the bobbin case with the projection (3) positioned against the spring (4).

(3) (4)

6. Make sure that the needle is at its highest position and put and slide the needle plate into position as illustrated.

Cleaning the sewing machine and foot controller After using, keep sewing machine and foot controller clean. Use dry rags to remove dust from the sewing machine and foot controller.

Page 53 of the Singer Sewing Machine user manual — ATTENTION
Page 53 · click to enlarge
Page 53

3. ENTRETIENT DE LA MACHINE

3. CUIDE SU MAQUINA

NETTOYAGE DES GRIFFES ET AUTOUR DU CROCHET

LIMPIAR EL AREA DEL TRANSPORTADOR Y LA LANZADERA

Siempre desconecte la máquina de la fuente de alimentación retirando el enchufe del tomacorriente de la pared.

Débranchez toujours la machine de l’alimentation électrique en retirant la fiche de la prise murale.

ATTENTION

PRECAUCION

Pour assurer un meilleur rendement de la machine, il est nécessaire de garder les pièces essentielles toujours propres.

Es necesario que mantenga las piezas esenciales limpias siempre, para obtener un funcionamiento eficiente de su máquina.

1. Relever l’aiguille à sa position la plus haute.
1. Levantar la aguja a la posición más alta.
2. Enlevez les deux vis de la plaque d’aiguille (1) et faite glisser la plaque d’aiguille vers vous comme dans l’illustration retirez la plaque.
2. Quitar dos tornillos en la placa de la aguja y deslice la placa de la aguja (1) hacia usted según se ilustra para su remoción.
3. Enlevez le porte canette.(2).
3. Quite la caja bobina (2).
4. Nettoyer les griffes et l’emplacement du crochet avec la brosse.
4. Limpiar el área del transportador y de la lanzadera con el cepillo.

Mettre une goutte d’huile pour machine à coudre sur le rebord du crochet comme indiquez par les flèche (A,B).

Ponga una gota de aceite para máquina de coser por el eje central de lanzadera y el carril de lanzadera como está indicado con las fiechas. (A, B)

5. Replacez le porte canette en vous assurant que la projection (3) appuis sur le ressort (4).
5. Vuelva a colocar la caja bobina con el reborde (3) contra el muelle (4).
6. Assurez-vous que l’aiguille est à sa position la plus haute et faite glisser la plaque d’aiguille pour la mettre en place tel qu’illustré.
6. Asegúrese de que la aguja esté en su posición más alta y colocada, deslice la placa de la aguja dentro de la posición según lo ilustrado.

Nettoyage de la machine à coudre et du rhéostat Après l’utilisation, garder la machine à coudre et le rhéostat propre, utilisez un chiffon sec pour enlever la poussière sur la machine et le rhéostat.

Limpieza de la máquina de coser y el pedal de control Después de usar, manténga la máquina y el pedal limpios. Utilice trapos secos para quitar el polvo de la máquina de coser y del regulador del pie.

électrique.

Page 54 of the Singer Sewing Machine user manual — STRAIGHT STITCH NEEDLE POSITION
Page 54 · click to enlarge
Page 54

4. OTHER INFORMATION

SATIN STITCH FOOT

The satin stitch foot is grooved to permit dense stitching to pass under it easily. It is most useful for sewing satin stitches and as an alternative to the general purpose foot when sewing stretch stitches.

Closely spaced zig-zag stitches are called satin stitches. This is an attractive stitch used primarily for appliqueing and bar tacking. Slightly loosen top thread tension for satin stitching. Use a backing of tissue paper or interfacing for lightweight fabrics to avoid puckering.

TWIN NEEDLE (Optional)

A twin-needle produces two rows of parallel stitches for pin tucks, double top stitching and decorative sewing.

When using a twin-needles, the stitch width should never be set beyond a twin needle mark, regardless of the stitch you have selected. Doing so will result in broken needles and possible damage to your machine.

Use of a Singer brand 3mm (Style 2025) twin needle is recommended. Twin needles are available in a range of sizes. Check with your Singer retailer.

The twin needle is an optional purchase.

THREADING THE TWIN NEEDLE

1. Insert the second spool pin. Place a spool on each spool pin. Thread the two threads as one. Draw one thread through each needle from front to back.
2. Pick up bobbin thread as for single needle sewing. Pull the three threads together under the presser foot to the back of the machine, leaving about 6” (15 cm) of thread.

Helpful hints: 1. Always move the stitch width to the twin needle mark prior to selecting a pattern. This will preclude any possibility of the twin needle breaking. 2. Turning off the machine returns the machine to normal sewing mode. Twin needle is only active when the twin needle switch is lit red.

STRAIGHT STITCH NEEDLE POSITION

The position of the needle when sewing straight stitch may be adjusted to 13 different positions with the stitch width control as illustrated:

Toward left Vers la gauche Hacia izquierda

Toward right Vers la droite Hacia derecha

Width control Contrôle de la largeur Control ancho

Page 56 of the Singer Sewing Machine user manual — THREAD PROBLEMS
Page 56 · click to enlarge
Page 56

5. PERFORMANCE CHECKLIST

GENERAL PROBLEMS

Machine does not sew. * Power switch is turned off.- Turn on the switch. * Buttonhole lever is not raised when sewing stitch patterns. – Raise buttonhole lever. * Buttonhole lever is not lowered when sewing buttonhole. – Lower buttonhole lever. * Bobbin winder is engaged. – Disengage bobbin winder (see page 14 - 15). * Presser foot is not lowered - Lower presser foot. Machine jams/knocks. * Thread is caught in hook.- Clean hook (see page 50 - 51). * Needle is damaged.- Replace needle (see page 23). Fabric does not move. * Presser foot is not lowered - Lower presser foot. * Stitch length is too short - Lengthen stitch length. * Feed dogs are lowered - Raise feed dogs.

STITCHING PROBLEMS

Machine skips stitches. * Needle is not all the way up into needle clamp(see page 23). * Needle is bent or blunt. - Replace needle (see page 23). * Machine is not threaded correctly (see page 18 - 19). * Thread is caught in hook. - Clean hook (see page 50 - 51). Stitches are irregular. * Needle size is not correct for thread and fabric (see page 22). * Machine is not threaded correctly (see page 18 - 19). * Top thread tension is too loose (see page 24 - 25). * Fabric is being pulled or pushed against machine feeding action. - Guide it gently. * Bobbin has not been wound evenly. - Rewind bobbin. Needle breaks. * Fabric is being pulled or pushed against machine feeding action. - Guide it gently. * Needle size is not correct for thread and fabric (see page 22). * Needle is not all the way up into the needle clamp (see page 23). * Twin needle is being used but stitch width is set too wide (see page 52 - 53).

THREAD PROBLEMS

Thread bunches. * Top and bobbin threads are not drawn back under presser foot before starting seam. - Draw both threads back under presser foot about 6 inches (10 cm) and hold until a few stitches are formed. Needle thread breaks. * Machine is not threaded correctly (see page 18 - 19). * Top thread tension is too tight (see page 24 - 25). * Needle is bent. - Replace needle (see page 23). * Needle size is not correct for thread and fabric (see page 22). Bobbin thread breaks. * Bobbin case is not threaded correctly (see page 16 - 17). * Lint accumulates in bobbin case or hook. - Remove lint (see page 50 -51). Fabric puckers. * Top thread tension is too tight. - Adjust thread tension (see page 24 - 25). * Stitch length is too long for sheer or soft fabric. - Shorten stitch length.

Page 58 of the Singer Sewing Machine user manual — SYSTEM ERROR
Page 58 · click to enlarge
Page 58

HELPFUL MESSAGES

Messages are displayed with LED lamps above the stitch selection panel on the machine. When a message is displayed, you may fix the problem by following the correction suggestion most suited to your issue. The corrections are preceded by an arrow.

Helpful message on control panel

1. The bobbin winder shaft is in the incorrect position for the function you have selected. Position the bobbin winder shaft to the left position for sewing and to the right position for

bobbin winding. 2. The reverse button is pressed during bobbin winding. Do not press reverse button during bobbin winding.

1. Buttonhole stitch is selected on the stich control panel; however the buttonhole lever is not in the correct position. Lower buttonhole lever and begin sewing the buttonhole. 2. A stitch pattern is selected; however the buttonhole lever is engaged (lower position). Raise buttonhole lever and begin sewing. 3. The buttonhole lever is in an incorrect starting position. Lower the buttonhole lever so that it drops down vertically between the stoppers. See page

46 for details.

1. Something other than foot control is detected in the machine socket for the foot control. Remove foreign particle from socket. 2. Foot control is connected or disconnected. This is not an error message. It only indicates the connection or disconnection of the foot

control and the C3 message will disappear in a few seconds. No correction is needed.

1. Machine does not operate due to thread tangles in bobbin case or jamed fabric. Turn off power switch and eliminate the problem that caused the machine to stop.
1. The stitch pattern selected, does not operate when the reverse/tacking stitch is pushed. Select a stitch pattern that can be operated in the reverse/tacking stitch mode.
1. The top thread has broken. Lift presser foot lifter. Pull to remove top thread from machine and rethread.
1. The foot controller was pushed down to start sewing before the presser foot was lowered. Lower presser foot and begin sewing.

SYSTEM ERROR

All system error corrections are as follows. Turn off and on the power switch to eliminate the problem that caused the system error to occur. If the error number should not disappear, consult an authorized technician.

Misfunction of main shaft motor.

Abnormal signal from bobbin winder shaft.

Abnormal signal from cam sensors.

Reverse stitch button is engaged, when the power is tuned on.

Problem Correction

Page 59 of the Singer Sewing Machine user manual — F-3
Page 59 · click to enlarge
Page 59

MESSAGES D’AIDE

MENSAJES DE AYUDA

Los mensajes son desplegados con los indicadores LED arriba del panel de selección de puntada en la máquina. Cuando se despliega un mensaje puede solucionar el problema siguiendo la sugerencia de corrección que mejor se adapte a su situación. Las correcciones están precedidas por una flecha.

Les messages apparaissent sur l’écran ACL qui se retrouvent au-dessus du panneau de sélection des motifs de la machine. Lorsqu’un message apparaît, vous pouvez le réglé le problème en suivant les corrections qui correspondent le mieux à la situation. La correction est précédée par une flèche.

Problème Correction Problema Corrección

1. Le bobineur n'est pas dans la bonne position pour la fonction que vous avez sélectionnée. Déplacer le bobineur vers la gauche en mode couture et
1. El eje del devanador está en la posición incorrecta para la función que ha seleccionado. Coloque el devanador en la posición izquierda para

vers la droite en mode bobinage. 2. Le bouton de marche arrière à été activé durant le bobinage. N'appuyer pas sur le bouton de marche arrière durant le

coser y en la derecha para llenar la bobina. 2. El botón de reversa es presionado durante el devanado de la bobina. No presione el botón de reversa durante el devanado

bobinage.

de la bobina.

1. La boutonnière a été sélectionné sur le panneau de commande; cependant le levier de la boutonnière n'est pas à la bonne place. Abaissez le levier de boutonnière pour coudre une
1. Está seleccionada la puntada de ojal en el panel de control; sin embargo la palanca del ojal no está en la posición correcta. Baje la palanca del ojal y comienze con la costura del

boutonnière. 2. Un motif a été sélectionné; cependant le levier de boutonnière est engagé (position basse). Soulevez le levier de boutonnière pour coudre. 3. Le levier de boutonnière n'est pas à la bonne position de départ. Abaissez le levier de boutonnière verticalement entre

mismo. 2. Está seleccionado un patrón de puntada; no obstante está usándose la palanca de ojal (posición abajo). Levante la palanca del ojal y comience a coser. 3. La palanca para ojales está en una posición incorrecta de inicio. Baje la palanca de ojales de modo que caiga verticalmente

les butées d'arrêt. Voir page 57 pour les détails.

entre los topes. Ver página 46 para detalles.

1. Un objet autre que le rhéostat est détecté dans la prise du réhostat. Retirez l'objet de la prise du réhostat. 2. Le rhéostat est branché ou débranché. Ceci n'est pas un message d'erreur. Cela vous indique
1. Algo más que el pedal de control se detecta en el receptáculo (clavija) de la máquina del control de pedal. Retire culaquier particula extraña al receptáculo. 2. El control de pedal está conectado o desconectado. Este no es un mensaje de error. Solo indica la conexión

seulement que le rhéostat est branché ou débranché et le message C3 disparaitra après quelques secondes. Aucune correction n'est requise.

o desconexión del control de pedal y el mensaje C3 desparecerá en unos cuantos segundos. No se necesita de corrección.

1. La machine ne fonctionne pas due au fil qui est coincé dans le porte canette ou dans le tissus. Éteignez la machine et réglez le problème qui cause
1. La máquina no opera debido a hebras enredadas en la caja bobina o tela atascada. Apague el interruptor y elimine el problema que causó

l'arrêt de la machine.

la parada de la máquina.

1. Le motif sélectionné, ne peut fonctionner lorsque vous appuyez sur le bouton de marche arrière/point d’arrêt. Selectionnez un motif qui peut fonctionner en mode de
1. El patrón de costura seleccionado no opera cuando se presiona la puntada de reversa/refuerzo. Seleccione un patrón de puntada que pueda operarse

marche arrière/point d’arrêt.

en el modo de puntada de reversa/refuerzo.

1. Le fil supérieur est cassé. Soulevez le pied presseur. Retirez le fil supérieur de la
1. Se ha roto el hilo superior. Levante el pie prensatelas. Jale para remover el hilo

machine et enflez de nouveau le fl supérieur. (voir page 9)

superior de la máquina y ensarte de nuevo.

1. Le rhéostat est activé avant d’avoir abaissé le pied presseur. Abaissez le pied presseur et coudre.
1. El control de pedal fue presionado para empezar a coser antes de bajar el pie prensatelas. Baje el pie prensatelas y comience a coser.

ERREUR DU SYSTÈME

ERRORES DEL SISTEMA

Toutes les corrections d'erreur du système sont les suivantes. Mettre l'interrupteur Moteur/Lumière en mode fermé et

Todas las correcciones del sistema son como sigue. Apague y encienda el interruotor para eliminar el problema

ensuite ouvert pour éliminer la cause de l'apparition de l'erreur du système. Si le code d'erreur ne disparait pas consultez un technicien autorisé.

que causó el error. Si no desaparece el número de error, consulte a un técnico autorizado.

Mauvais fonctionnement de l’arbre principal du moteur. Mal funcionamiento del motor del eje principal.

Signal anormal de l’axe du bobineur. Señal anormal del eje del devanador de bobina.

Signal anormal des senseurs. Señal anormal de los sensores de leva.

Le bouton de marche arrière est activé lorsque l’interrupteur Moteur/Lumière est mis en mode ouvert.

Está activo el botón de puntada en reversa, cuando la alimentación está encendida.

F-3

Page 60 of the Singer Sewing Machine user manual — ENGLISH / FRANÇAIS / ESPAÑOL
Page 60 · click to enlarge
Page 60

ENGLISH / FRANÇAIS / ESPAÑOL

© Part No. 83933 4 /12

F-4

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
1. The bobbin winder shaft is in the incorrect position for the function you have selected.  Position the bobbin winder shaft to the left position for sewing and to the right position for bobbin winding. 2. The reverse button is pressed during bobbin winding.  Do not press reverse button during bobbin winding. p.58
1. Buttonhole stitch is selected on the stich control panel; however the buttonhole lever is not in the correct position.  Lower buttonhole lever and begin sewing the buttonhole. 2. A stitch pattern is selected; however the buttonhole lever is engaged (lower position).  Raise buttonhole lever and begin sewing. 3. The buttonhole lever is in an incorrect starting position.  Lower the buttonhole lever so that it drops down vertically between the stoppers. See page 46 for details. p.58
1. Something other than foot control is detected in the machine socket for the foot control.  Remove foreign particle from socket. 2. Foot control is connected or disconnected.  This is not an error message. It only indicates the connection or disconnection of the foot control and the C3 message will disappear in a few seconds. No correction is needed. p.58
1. Machine does not operate due to thread tangles in bobbin case or jamed fabric.  Turn off power switch and eliminate the problem that caused the machine to stop. p.58
1. The stitch pattern selected, does not operate when the reverse/tacking stitch is pushed.  Select a stitch pattern that can be operated in the reverse/tacking stitch mode. p.58
1. The top thread has broken.  Lift presser foot lifter. Pull to remove top thread from machine and rethread. p.58
1. The foot controller was pushed down to start sewing before the presser foot was lowered.  Lower presser foot and begin sewing. p.58

Ask about the Singer Sewing Machine

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Singer Sewing Machine

Be the first to ask — other owners or our team will answer.

Original document

Singer Sewing Machine manual PDF

60 pages·10.3 MB·Household Appliance·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…