EN
Singer logo
Official user manual

Singer Sewing Machine (7258)

84 pages·17.8 MB·Household Appliance·PDF·ENDEFRITNLJA
Singer Sewing Machine (7258)
Table of Contents 3 sections 7258 Instruction Manual_cover · 7258 Instruction Manual · 7258-P52-84 ShowHide
Page 1 of the Singer Sewing Machine (7258) user manual — 7258 Instruction Manual_cover
Page 1 · click to enlarge
Page 1
Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 1)
Fig. 1 · 7258 Instruction Manual_cover
Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 1)
Fig. 2 · 7258 Instruction Manual_cover
Page 2 of the Singer Sewing Machine (7258) user manual — “SAVE THESE INSTRUCTIONS”
Page 2 · click to enlarge
Page 2

“IMPORTANT SAFETY INSTRUCTIONS”

“When using an electrical appliance, basic safety precautions should always be followed, including the following.” “Read all instructions before using this sewing machine.” “DANGER--To reduce the risk of electric shock:”

1. “This sewing machine should never be left unattended when plugged in. Always unplug this sewing machine from the electric

outlet immediately after using and before cleaning.” 2. “Always unplug before replacing light bulb. Replace bulb with same type rated DC 6.5 V 2.8 Watts.”

“WARNING -

To reduce the risk of burns, fire, electric shock, or injury to persons: ”

1. “Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children.” 2. “Use this sewing machine only for its intended use as described in this manual. Use only attachments recommended by the

manufacturer as contained in this manual.” 3. “Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped

or damaged, or dropped into water. Return the sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.” 4. “Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot

control free from the accumulation of lint, dust, and loose cloth.” 5. “Never drop or insert any object into any opening.” 6. “Do not use outdoors.” 7. “Do not operate where aerosol (spray) products are being used or where oxygen is being administered.” 8. “To disconnect, turn switch to the off (“0”) position, then remove plug from outlet.” 9. “Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.” 10. “Keep fingers away from all moving parts. Special care is required around the sewing machine needle.” 11. “Never sew with a damaged needle plate as this can cause a needle to break.” 12. “Do not use bent needles.” 13. “Do not pull or push fabric while stitching. It may deflect the needle causing it to break.” 14. “Switch the sewing machine off (“0”) when making any adjustments in the needle area, such as threading needle, changing needle, threading bobbin, or changing presser foot, etc.” 15. “Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual.”

“CAUTION - -

Moving parts-To reduce risk of injury, switch off before servicing. Close cover before operating machine.”

“SAVE THESE INSTRUCTIONS”

“This product is for household use, or equivalent.”

FOOT CONTROL (USA & Canada only) Use Yamamoto Electric, Model YC-485 EC with this sewing machine.

POLARIZED PLUGS CAUTION (USA & Canada only) This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

This appliance complies with EEC Directive 2004/108/EC covering the electromagnetic compatibility.

Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/ electronic products. If in doubt please contact your retailer for guidance.

SINGER is a registered trademark of The Singer Company Limited or its affiliates.

©2008 The Singer Company Limited or its affiliates. All rights reserved.

Page 8 of the Singer Sewing Machine (7258) user manual — MACHINE IDENTIFICATION
Page 8 · click to enlarge
Page 8

1. KNOWING YOUR SEWING MACHINE

MACHINE IDENTIFICATION

Singer Sewing Machine (7258) — MACHINE IDENTIFICATION diagram (page 8)
Fig. 3
1. Bobbin winding tension disk 2. Thread take-up 3. Thread tension control 4. Face cover 5. Thread cutter 6. Removable extension table/

Accessory box 7. Bobbin winder shaft 8. Bobbin winder stop 9. Sewing speed control 10. Pattern number reference guide 11. Operation buttons 12. Horizontal spool pin 13. Handle 14. Hand wheel 15. Power/light switch 16. Cord socket 17. Identification plate 18. Presser foot lifter 19. Buttonhole lever 20. Thread guide 21. Automatic needle threader 22. Thread guide 23. Thread guide 24. Presser foot screw 25. Needle 26. Bobbin cover plate 27. Needle bar 28. Thread cutter 29. Foot release lever 30. Needle clamp screw 31. Presser foot 32. Feed dogs 33. Needle plate 34. Bobbin cover release button 35. Large extension table 36. Power line cord 37. Foot control 38. Instruction manual

Page 10 of the Singer Sewing Machine (7258) user manual — ACCESSORIES
Page 10 · click to enlarge
Page 10
Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 10)
Fig. 4 · 7258 Instruction Manual_cover

ACCESSORIES

1. Needles
2. Bobbins (4 total - 1 in machine)
3. Auxiliary spool pin
4. Spool pin felt discs (2)
5. Spool pin cap (mini)
6. Spool pin cap (small)
7. Spool pin cap (large)
8. Buttonhole opener/Seam Ripper and Brush
9. Screwdriver for needle plate
10. Darning plate
11. Zipper foot
12. Satin stitch foot
13. Blind stitch foot
14. Buttonhole foot
15. Overcasting foot
16. Darning & embroidery foot
17. Gathering foot
18. Rolled hem foot
Singer Sewing Machine (7258) — ACCESSORIES diagram (page 10)
Fig. 5

The Foot that comes on your Sewing machine is called the General Purpose Foot and will be used for the majority of your sewing.

The Satin Foot (12) is another very useful foot and should be used for most decorative sewing.

When purchasing additional bobbins, be sure they are Class I5 J.

Page 12 of the Singer Sewing Machine (7258) user manual — WHEN USING POWER LINE CORD ONLY
Page 12 · click to enlarge
Page 12

SETTING UP YOUR MACHINE

Be sure to wipe off any excess oil from needle plate area before using your machine the first time.

WHEN USING POWER LINE CORD ONLY

WHEN USING POWER LINE CORD AND FOOT CONTROL Connect the plug of the power line cord into the cord socket (1) and your wall outlet (2) as illustrated (B).

Connect the plug of the power line cord into the cord socket (1) and your wall outlet (2) as illustrated (A).

Connect the foot control plug into the machine socket (3).

Singer Sewing Machine (7258) — WHEN USING POWER LINE CORD ONLY diagram (page 12)
Fig. 6

Set power/light switch at “OFF” Mettez l’interrupteur moteur/lumière sur “OFF”. Poner el Interruptor de corriente/luz de velocidad en “OFF”

Poner el Interruptor de corriente/ luz de velocidad en “OFF”

machine socket Connecteur de la machine Conector de la máquina

Power line cord Cordon Cordón de la linea eléctrica

Power line cord Cordon Cordón de la linea eléctrica

Always disconnect the machine from power supply by removing the plug from the wall-outlet.

Your machine will not operate until the power/light switch is turned on. The same switch controls both the power and the light.

Power/light switch “OFF” Interrupteur moteur/lumière “OFF” Interruptor corriente/luz “OFF”

Power/light switch “ON” Interrupteur moteur/lumière “ON” Interruptor corriente/luz “ON”

When servicing the machine, or changing needles, etc., machine must be disconnected from the power supply.

Page 13 of the Singer Sewing Machine (7258) user manual — INTERRUPTEUR MOTEUR ET LUMIÈRE
Page 13 · click to enlarge
Page 13

PRÉPARATION DE LA MACHINE

PRÉPARACION DE LA MÁQUINA

Assurez-vous d’essuyer tout surplus d’huile autour de la plaque à aiguille, avant d’utiliser votre machine pour la première fois.

Asegúrese de limpiar cualquier sobrante de aceite del área de la placa aguja antes de usar su máquina por primera vez.

En utilisant uniquement la fiche électrique.

CUANDO SE USE EL CORDÓN DE LA LÍNEA ELÉCTRICA SOLAMENTE Conecte el cordón de la línea eléctrica a la máquina (1) y el enchufe a la alimentación de corriente en la pared (2) tal como se ve en la ilustración (A).

Brancher la fiche du cordon électrique dans la prise de la machine (1) et dans la prise électrique murale(2) comme indiqué (A).

En utilisant la fiche électrique et le rhéostat. Brancher la fiche du cordon électrique dans la prise de la machine (1) et dans la prise électrique murale(2) comme indiqué (B).

CUANDO SE USE EL CORDÓN DE LÍNEA ELÉCTRICA Y EL CONTROL DE PEDAL Conecte el cordón de la línea eléctrica a la máquina (1) y el enchufe a la alimentación de corriente en la pared (2) tal como se ve en la ilustración (B).

Brancher la fiche du rhéostat dans la prise (3).

Conectar el enchufe del control de velocidad de pedal en el conector de la máquina (3).

D é b r a n c h e z t o u j o u r s . L a m a c h i n e d e l’alimentation électrique en retirant la fiche de la prise murale.

Siempre desconecte la máquina de la fuente de alimentación retirando el enchufe del tomacorriente de la pared.

INTERRUPTEUR MOTEUR ET LUMIÈRE

INTERRUPTOR CORRIENTE/LUZ

Votre machine est équipée d’un interrupteur unique moteur/ lumière. Vous piquez donc constamment avec votre travail éclairé.

La máquina no funcionará hasta que se conecte el interruptor de corriente/luz. El mismo interruptor controla la corriente y la luz. Cuando se está utilizando la máquina, o se están cambiando agujas o bobinas, etc., la máquina se debe desconectar de los suministros principales.

Page 14 of the Singer Sewing Machine (7258) user manual — DARNING PLATE
Page 14 · click to enlarge
Page 14

SPOOL PINS

Singer Sewing Machine (7258) — SPOOL PINS diagram (page 14)
Fig. 7

HORIZONTAL SPOOL PIN

Place thread spool on the pin and secure with a spool cap to ensure smooth flow of thread. If the thread spool has a thread retaining slit, it should be placed to the right.

Spool pin felt discs Rondelle feutre Disco del pasador carrete

Select the correct spool pin cap according to the type and diameter of spool being used. The diameter of the spool pin cap should always be larger than that of the spool itself.

Vertical spool pin Porte-bobine vertical Pasador de carrete vertical

Thread retaining slot Fente de retenue de fil Ranura de retención de hilo

VERTICAL SPOOL PIN

Attach the spool pin and place a felt disc over it. Place a spool of thread on the spool pin.

PRESSER FOOT LIFTER

Singer Sewing Machine (7258) — PRESSER FOOT LIFTER diagram (page 14)
Fig. 8

There are three positions for your presser foot.

1. Lower the presser foot to sew.
2. Raise the lifter to the middle position to insert or remove fabric, and to change presser foot.
3. Lift it to its highest position to accommodate thicker fabrics.

DARNING PLATE

Use the darning plate when you need to control fabric feeding for button sewing, free motion work and free motion darning.

Raise needle and presser foot, and position darning plate onto the needle plate with the two pins on the back inserted to the holes of needle plate.

Page 15 of the Singer Sewing Machine (7258) user manual — PLAQUE DE REPRISAGE
Page 15 · click to enlarge
Page 15

PORTE-BOBINE

PORTA CARRETES

PORTE-BOBINE HORIZONTAL

PORTA CARRETE HORIZONTAL

Placez la bobine sur la tige et fixez-y un couvre-fil pour assurer un débit de fil bien régulier. Si la bobine est dotée d’une fente de retenue de fil, elle doit être placée à la droite.

Coloque el carrete de hilo en el porta carrete y asegúrelo con el sujetador de hilo para asegurarse que el hilo se mueve suavemente. El carrete de hilo tiene una ranura de retención de hilo, que debe quedar hacia la derecha.

Sélectionner le couvre-fil correcte en fonction du type et du diamètre de la bobine utilisée. Le diamètre du couvre-fil doit toujours être supérieur à celui de la bobine elle-même.

Seleccione la tapa de pasador de carrete de acuerdo al tipo y diámetro del carrete usado. El diámetro de la tapa de pasador de carrete debe ser siempre mayor que la del mismo carrete.

PORTE-BOBINE VERTICAL

PORTA CARRETE VERTICAL

Fixer le porte-bobine et la rondelle feutre sur le capot supérieur. Placer la bobine sur le porte-bobine.

Colocar el porta carrete y poner el disco de fieltro. Colocar un carrete de hilo en el portacarretes.

LEVIER DU PIED PRESSEUR

PALANCA PIE PRENSATELAS

Il y a 3 positions:

Su prensatelas tiene tres posiciones.

1. Abaisser le levier pour coudre.
1. Bajar el prensatelas para coser.
2. Soulever le levier en position moyenne pour insérer ou enlever le tissu, et changer le pied.
2. Levantar la palanca a la posición media para insertar o mover la tela.
3. Soulever le levier à sa position la plus haute, pour accommoder les tissus épais.
3. Levantar a la posición más alta para acomodar telas mas gruesas.

PLAQUE DE REPRISAGE

PLACA TRANSPARENTE

Utilisez la plaque de reprisage lorsque vous devez contrôler vous-même l’entraînement du tissu pour coudre des boutons, pour les travaux à mouvements libres et pour effectuer du reprisage par vous-même.

Use la placa transparente cuando deba controlar la alimentación del tejido para costura de botones, trabajo de bordado libre y zurcido.

Alzar la aguja y el pie prensatelas y montar la placa transparente en la plancha de agujas, con los dos pasadores de la parte posterior introducidos en los agujeros de la placa aguja.

Mettre l'aiguille à sa position la plus haute et relever le pied presseur. Placer la plaque à reprisage sur la plaque aiguille en veillant à ce que les deux tiges s'introduisent correctement dans les trous.

Page 16 of the Singer Sewing Machine (7258) user manual — CONVERTING TO FREE-ARM SEWING
Page 16 · click to enlarge
Page 16
Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 16)
Fig. 9 · 7258 Instruction Manual_cover

CONVERTING TO FREE-ARM SEWING

Your machine can be used either as a flat- bed or as a free- arm model.

With the extension table in position, it provides a large working surface.

To remove the extension table, hold it firmly with both hands and pull it off to the left as shown. To replace, slide the extension table back into place until it clicks.

With the extension table removed the machine converts into a free-arm model for sewing children’s clothes, cuffs, trouser legs, and other hard-to-reach places.

Singer Sewing Machine (7258) — CONVERTING TO FREE-ARM SEWING diagram (page 16)
Fig. 10

To place onto the machine, lift the supporting leg of the extension table, and slide the table into place while fitting the guide pins A, B, C and D into machine as illustrated.

Page 17 of the Singer Sewing Machine (7258) user manual — PLATEAU DE RALLONGE
Page 17 · click to enlarge
Page 17

UTILISATION DU BRAS LIBRE

UTILIZACIÓN DEL BRAZO LIBRE

Cette machine peut s’utiliser aussi bien sous la forme d’une base plane que celle d’un bras libre.

La máquina tanto se puede utilizar como base plana o una máquina de brazo libre.

En conservant la table de rallonge en place, vous obtiendrai une plus grande surface de travaille.

Con la base de extensión instalada se obtiene una superficie de trabajo más amplia.

Pour retirer la table de rallonge, tenez-la fermement avec les deux mains et tirez-la à gauche vers l’extérieur, comme indiqué sur l’illustration. Pour la remettre en place, faites glisser la table de rallonge à sa place jusqu’à ce qu’elle s’enclenche.

Para retirar la extensión de la cama, sosténgala firmemente con ambas manos y sáquela hacia la izquierda tal como se indica. Para volver a colocarla, deslice la extensión de la cama nuevamente a su lugar hasta que haga clic.

Sin la base de extensión, la máquina se convierte en un modelo de brazo libre para costura de ropa de niños, puños, piernas de pantalones, y otros lugares complicados.

En retirant la table de rallonge, la machine sera converti en bras-libre pour confectionner des vêtements d’enfants, poignets, pantalons ainsi que tout endroit difficile d’accès.

PLATEAU DE RALLONGE

BASE DE EXTENSION

Pour fixer à la machine, relever la patte de support du plateau de rallonge, et faite le glisser en positionnant les tiges A, B, C et D comme indiqués.

Para colocarla en la máquina, levante el soporte de la mesa de extensión para liberarla y deslícela en su lugar, ajustándola a la guías A, B, C y D en la máquina tal como se ilustra.

Page 18 of the Singer Sewing Machine (7258) user manual — WINDING THE BOBBIN
Page 18 · click to enlarge
Page 18

WINDING THE BOBBIN

Be sure to use Class 15 J bobbins.

1. Place a spool of thread on the spool pin, and secure it with the spool pin cap. Pull the thread out from the spool and place it through thread guides as shown in illustration.

Be sure to pull thread securely into the bobbin winding tension disk.

2. Put end of thread through the hole in bobbin as shown. Push bobbin winder shaft to far left position, if it is not already there.
3. Place bobbin onto shaft with end of thread coming from top of bobbin. Push bobbin winder shaft to the right until it clicks. Hold the end of thread.
4. Start machine and the bobbin starts to wind. Bobbin will automatically stop turning when completely filled. Push shaft to the left to remove bobbin and cut thread.
Page 20 of the Singer Sewing Machine (7258) user manual — A
Page 20 · click to enlarge
Page 20

THREADING THE BOBBIN THREAD

1. Raise the needle to its highest position by rotating the hand wheel toward you (counter-clockwise).
2. Remove the bobbin cover plate by pushing the release button to the right. Bobbin cover will pop up sufficiently to allow you to remove the cover.
3. Insert the bobbin making sure the bobbin rotates counterclockwise when you pull the thread.
4. Pull thread through the slot (A) and then to the left.

A

5. With a finger held gently on top of the bobbin, pull the thread until it stops in slot (B). Then pull about 6" (15 cm) of thread and lead it towards back of the machine under the presser foot.

B NOTE: This is also a very important step to assure the bobbin thread does not slip out of position.

A

6. Replace the bobbin cover plate onto the needle plate.
Page 22 of the Singer Sewing Machine (7258) user manual — IMPORTANT:
Page 22 · click to enlarge
Page 22

THREADING THE TOP THREAD

Singer Sewing Machine (7258) — THREADING THE TOP THREAD diagram (page 22)
Fig. 11

A. Raise the presser foot lifter. Always be sure to raise the

presser foot lifter before threading the top thread. (If the presser foot lifter is not raised, correct thread tension cannot be obtained.)

B. Turn the hand wheel toward you until the needle is in its

highest position.

C. Thread the machine with your left hand while firmly gripping

the thread with your right hand in the following order as illustrated.

* Guide the thread through thread guide (1), and then pull

it into the pre-tension guide (2).

* Pull the thread into the tension discs (which are located

inside the machine) by first passing the thread to the left of plate (2). Then guide the thread to the bottom of the groove. * Do a U-turn around the inside of the tab (3).

* Pass the thread through the thread take-up (4) from right

to left.

* Pull the thread into the inside of the take-up lever until it

reaches the eye of the lever.

* Guide the thread into the thread guide (5).

* Pass the thread through the eye of the needle (6) from

front to back. (See following page for instructions on operation of the Automatic Needle Threader.)

IMPORTANT:

To verify that the machine is threaded properly in the tension discs, do this simple check:

1.) With the presser foot raised and the

needle unthreaded, pull the thread. You should detect only a slight resistance and little or no deflection of the needle.

2.) Now lower the presser foot and again

pull the thread towards the the back of the machine. This time you should detect a considerable amount of resistance and much more deflection of the needle. If you do not detect the resistance, this means you have not threaded the machine correctly and need to rethread it.

Page 23 of the Singer Sewing Machine (7258) user manual — IMPORTANT:
Page 23 · click to enlarge
Page 23

ENFILAGE DU FIL SUPÉRIEUR

ENHEBRADO DEL HILO SUPERIOR

A. Elevez le pied presseur. Veillez à toujours élever le

A. Levante el prensatelas. Siempre asegúrese de levantar

releveur de pied presseur avant d’enfiler le fil supérieur. (Si le releveur de pied presseur n’est pas élevé, vous ne pourrez pas obtenir une tension de fil correcte.)

el prensatelas antes de enhebrar el hilo superior. (Si no se levanta el prensatelas, no se podrá lograr la tensión correcta del hilo.)

B. Tournez le volant vers vous jusqu’à ce que l’aiguille soit en

B. Gire el volante hasta que la aguja se encuentre en su

position haute et que le releveur de fil soit visible.

posición más alta y el tirahilos quede a la vista.

C. Enfilez le fil de la machine avec votre main gauche tout

C. Enhebre la máquina con su mano izquierda mientras

en tenant le fil fermement de la main droite dans l’ordre suivant comme montré dans l’illustration.

toma firmemente el hilo con su mano derecha en el orden siguiente tal como está ilustrado.

* Faites passer le fil par le guide-fil (1), puis tirez-le dans le

* Guíe el hilo a través de la guía de hilo (1), y luego páselo

guide de prétension (2).

por la guía de tensión preliminar (2).

* Passer le fil du coté gauche de la plaque (2) et tirer

* Lleve el hilo a los discos de tensión, primero pasando el

ensuite le fil entre les disques de tension. Puis guidez le fil au fond de la rainure.

hilo a la izquierda de la cubierta (2). Luego guíe el hilo hasta el fondo de la ranura.

* Faites faire un demi-tour au fil autour de l’intérieur de la

* Dé una vuelta en U alrededor del interior de la lengüeta (3).

languette (3).

* Pase el hilo a través del tirahilos (4) de derecha a

* Faites passer le fil par le releveur de fil (4) de la droite

izquierda.

vers la gauche.

* Pase el hilo por el interior de la palanca de tirahilos hasta

* Tirez le fil à l’intérieur du levier de releveur de fil jusqu’à

que llegue al ojo de la palanca.

ce qu’il atteigne l’orifice du levier.

* Guíe el hilo por la guía de hilo (5).

* Guidez le fil dans le guide-fil (5).

* Pase el hilo a través del ojo de la aguja (6) de adelante

* Faites passer le fil par l’orifice de l’aiguille (6) de l’avant

hacia atrás. (Continúe con la página siguiente por instrucciones sobre el funcionamiento del ensartador automático de agujas.)

vers l’arrière. (Reportez-vous à la page suivante pour les instructions concernant le fonctionnement de l’enfileur de chas d’aiguille automatique.)

IMPORTANT:

IMPORTANTE:

Pour vous assurer que la machine est correctement pourvue de fil dans les disques de tension, effectuez cette simple vérification:

Para verificar que la máquina ha sido bien enhebrada en los discos de tensión, realice esta verificación sencilla:

1.) Con el prensatelas levantado y la aguja sin enhebrar,

1.) Avec le pied presseur relevé et l’aiguille non-enfilée,

jalar el hilo. Deberá detectar solo una ligera resistencia y una pequeña o ninguna deflexión de la aguja.

tirer sur le fil. Vous ne devriez sentir qu’une légère résistance ainsi qu’une faible ou aucune déflexion de l’aiguille.

2.) Ahora vuelva a bajar el pie prensatelas y vuelva

2.) Ensuite, abaisser le pied presseur et tirez de

a tirar del hilo hacia atrás de la máquina. En ese momento deberá detectar una cantidad considerable de resistencia y mucha más deflexión de la aguja. Si no detecta la resistencia ha enhebrado mal la máquina y deberá volver a enhebrarla.

nouveau le fil vers l’arrière de la machine. Cette fois, vous devriez sentir une forte résistance et beaucoup plus de déflexion de l’aiguille. Si vous ne sentez pas de résistance, le fil a été mal enfilé et vous devez le réenfiler.

Page 24 of the Singer Sewing Machine (7258) user manual — USING AUTOMATIC NEEDLE THREADER
Page 24 · click to enlarge
Page 24

USING AUTOMATIC NEEDLE THREADER

Raise the needle to its highest position by rotating the hand wheel towards you (counter-clockwise).

1. Hook thread into thread guide as illustrated.
2. Pull down lever while holding the end of thread.
3. Rotate the lever to the rear of the machine.
4. Guide thread into hooked end and pull the thread upward.
5. Return the lever and needle will be threaded automatically.
6. Release the lever and pull thread away from you.
Singer Sewing Machine (7258) — USING AUTOMATIC NEEDLE THREADER diagram (page 24)
Fig. 12
Page 26 of the Singer Sewing Machine (7258) user manual — PICKING UP BOBBIN THREAD
Page 26 · click to enlarge
Page 26

PICKING UP BOBBIN THREAD

1. Raise the presser foot lifter.
2. Holding needle thread loosely with your left hand, turn hand wheel toward you (counter-clockwise) with your right hand, first lowering the needle and continuing until the needle comes to its highest position.
3. Lightly pull up the top thread, and pick up bobbin thread, which will appear through the needle plate slot.
4. Pull both top and bobbin threads together toward the back of the machine under the presser foot, leaving about 6” (15 cm) clear.
Page 27 of the Singer Sewing Machine (7258) user manual — RAPPEL DU FIL INFÉRIEUR
Page 27 · click to enlarge
Page 27

RAPPEL DU FIL INFÉRIEUR

EXTRACCIÓN DEL HILO DE LA BOBINA

1. Relever le pied presseur.
1. Alzar la palanca del pie prensatelas.
2. Tenir le fil de l’aiguille et tourner le volant vers vous en faisant remonter l’aiguille à sa position la plus haute.
2. Manteniendo flojo el hilo de la aguja con la mano izquierda, girar hacia usted el volante con la mano derecha, hasta que la aguja alcance su posición más alta.

La machine exécute un cycle et s’arrête avec l’aiguille relevée. Le fait qu’elle s’arrête toujours avec l’aiguille “complètement relevée” est l’une des caractéristiques de votre machine à coudre avec ordinateur.

Su máquina realizará un ciclo hacia abajo- arriba y se detendrá con la aguja levantada. Una de las características de su máquina de coser computarizada es que siempre se detiene con la aguja “completamente arriba”.

3. Faire remonter le fil inférieur en tirant légèrement sur le fil supérieur.
3. Tirar ligeramente del hilo superior y recoger el hilo de la bobina, que aparecerá a través de la abertura de la placa aguja.
4. Placer les deux fils sous le pied presseur vers l’arrière en laissant environ 15 cm fil dépasser.
4. Tirar de ambos hilos juntos, hacia atrás de la máquina, por debajo del pie prensatelas, dejando alrededor de 15 cm. de hilo.
Page 28 of the Singer Sewing Machine (7258) user manual — Changing the needle
Page 28 · click to enlarge
Page 28

NEEDLE, THREAD AND FABRIC CHART

Your fabric will determine the choice of a needle and thread. The following table is a practical guide to needle and thread selection. Always refer to it before a new sewing project. In most cases, you will use the same size and type of thread in the bobbin as in the top thread supply.

FABRICS THREAD NEEDLES The fabrics below can be of any fiber: cotton, linen, silk, wool, synthetic, rayon, blends. They are listed as examples of weight. Light- Weight

TYPE SIZE

Cotton-wrapped Polyester 100% Polyester * Mercerized Size 60 Cotton-wrapped Polyester 100% Polyester * Mercerized Size 50 Nylon

Corduroy Flannel Gabardine Gingham Linen Muslin Wool Crepe Medium- Heavy

Bonded Wovens Canvas Coating Denim Duck Sailcloth

Cotton-wrapped Polyester 100% Polyester * Mercerized Size 40 * "Heavy Duty"

Knits Bonded Knits Double Knit Jersey Tricot

Cotton-wrapped Polyester Polyester Nylon

* Do not use on stretch fabrics. * For best sewing results, always use a SINGER branded needle.

Always disconnect the machine from power supply by removing the plug from the wall-outlet.

Changing the needle

1. Raise the needle bar to its highest position by turning the hand wheel toward you (counter-clockwise).

Flat side Côté plat Lado plano

2. Loosen the needle clamp screw by turning it toward you (counter-clockwise).
3. Remove the needle by pulling it downward.
4. Insert the new needle into the needle clamp with the flat side toward the back.

Stop pin Butée Pasador

5. Push the needle up as far as it can go.
6. Tighten the needle clamp screw with the screw driver.

Helpful Hint: Placing a scrap of fabric under the presser foot and lowering the presser foot makes it easier to change the needle and will preclude dropping the needle into the needle plate slot.

Flat side toward the back

Côté plat orienté vers l’arrière

Lado plano hacia fuera de Vd.

Show 19 more labels / short text on this page
Batiste Chiffon Crepe · 2020 red shank · 11/80 orange · band · Medium- Weight · 2020 red shank · 14/90 blue band · 2020 red shank · 16/100 purple · band · 18/110 yellow · band · 2045 yellow shank · 11/80 orange · band · 14/90 blue band · 16/100 purple · band · Needle Aiguille Aguja
Page 29 of the Singer Sewing Machine (7258) user manual — Changement d’aiguille
Page 29 · click to enlarge
Page 29

TABLEAU DES AIGUILLES, FIILS ET TISSUS

TABLA DE HILO, AGUJA Y MATERIAL

Le choix d’une aiguille et du fil correspondant à votre tissu est très important. Le tableau suivant vous aidera à faire le choix, avant d’entreprendre votre ouvrage. Normalement vous devriez utiliser la même grosseur et type de fil dans la bobine et comme fil supérieure.

Su material determinará la selección de aguja e hilo. Esta tabla es una guía práctica para la selección de aguja e hilo. Siempre buscar una referencia antes de coser el material nuevo. En la mayoría de los casos se deberá usar el mismo tamaño y tipo de hilo tanto en la bobina como en el abastecedor de hilo superior.

TISSUS FIL AIGUILLES Les tissus ci-dessous peuvent être de n’importe quelle fibre: coton, lin, soie, laine, synthétique,rayonne, composite. Ils sont énumérés en fonction de leur poids.

MATERIAL HILO AGUJAS Los materiales abajos pueden ser de cualquiera fibra: algodón, lino, seda, lana, sintetico, rayón, mezclas. Están listados como ejemplos de peso.

TYPE CALIBRE

LÉGERS Batiste Gaze Crêpe

Polyester-coton 100% polyester *Mercerisé calibre 60

TYPO TAMAÑO

Algodón sobre mecha polyester 100% Polyester * Mercerizado número 60 Algodón sobre mecha polyester 100% Polyester * Mercerizado número 50

MOYENS Velours côtelé Flanelle Gabardine Guigan Toile de lin Mousseline Crêpe de laine MOYENS- LOURDS

Polyester-coton 100% polyester *Mercerisé calibre 50 Nylon

Pana Franela Gabardina Guinga Lino Muselina Crepé de lana Medio pesado

Tissus apprêtés Toile forte Tissu de manteau Toile de jean Coutil Toile à voiles

Polyester-coton 100%polyester *Mercerisé calibre 40 *Fil fort

Tejido aglomerado Lona Abrigos Denim Loneta Material para Velamen Puntos Punto

Algodón sobre mecha polyester 100% Polyester * Mercerizado número 40

MAILLES Mailles apprêtés Maille double Jersey Tricot

Algodón sobre mecha polyester Polyester

aglomerado Punto doble Jersey Tricot

* Non recommandés pour les tissus extensibles. * Pour obtenir les meilleurs résultats de couture, utilisez toujours une aiguille de marque SINGER.

* No usar sobre el material estirado. * Para los mejores resultados de costura, use siempre agujas marca SINGER.

Débranchez toujours. La machine de l’alimentation électrique en retirant la fiche de la prise murale.

Siempre desconecte la máquina de la fuente de alimentación retirando el enchufe del tomacorriente de la pared.

Changement d’aiguille

Cambio de la aguja

1. Relever la barre à aiguille à sa position la plus haute en tournant le volant vers vous (sens contraire).
1. Levantar la barra de la aguja a la posición más alta girando el volante hacia Ud (en sentido contrario a las manecillas del reloj).
2. Desserrer la vis du serre-aiguille (sens contraire).
2. Aflojar el tornillo que sujeta la aguja girándolo hacia Ud (en sentido contrario a las manecillas del reloj).
3. Enlever l’aiguille en la tirant vers le bas.
4. Insérer la nouvelle aiguille dans le serreaiguille, avec le côté plat à l’arrière.
3. Quitar la aguja sacándola hacia abajo.
4. Insertar la aguja nueva en la barra aguja con el lado plano hacia la parte posterior.
5. Pousser l’aiguille vers le haut, jusqu’ à la butée.
6. Resserrez la vis de l’aiguille à l’aide du tournevis.
5. Empujar la aguja lo más arriba posible.
6. Apriete el tornillo de sujeción de aguja con el destornillador.

Suggestion utile: En plaçant un morceau de tissu sous le pied presseur et en abaissant le pied presseur, vous faciliterez l’opération de remplacement de l’aiguille, et ceci évitera toute chute de l’aiguille dans la fente de la plaque-aiguille.

Show 33 more labels / short text on this page
2020 tige rouge · 11/80 bague orange · Peso ligero · Batista Gasa Crepé · 2020 Vastago · 11/80 banda narranja · rojo 2020 Vastago · 2020 tige rouge · 14/90 bague · Peso medio · 14/90 banda · bleue · rojo · azúl · 2020 tige rouge · 16/100 bague pourpre · 2020 Vastago · 16/100 banda púrpula · rojo · 18/110 bague · jaune · Polyester-coton Polyester Nylon · 2045 tige jaune · 11/80 bague orange · 2045 amarilla · 11/80 banda narranja · 14/90 bague · rojo · bleue · 14/90 banda · 16/100 bague pourpre · azúl · 16/100 banda púrpula
Page 30 of the Singer Sewing Machine (7258) user manual — CHANGING PRESSER FOOT
Page 30 · click to enlarge
Page 30

ADJUSTING TOP THREAD TENSION

Under side Côté de dessous Reverso

90% of your sewing will be done with the tension control dial (on top of the machine) set at “AUTO” .

Singer Sewing Machine (7258) — ADJUSTING TOP THREAD TENSION diagram (page 30)
Fig. 13

Well balanced Correct Bien equilibrada

Helpful Hint: A slight adjustment to a higher number or a lower number may improve sewing appearance.

Top side Côté de dessus Cara

STRAIGHT STITCHING

The correct appearance of your stitching is largely determined by the balanced tension of both top and bobbin threads. The tension is well balanced when these two threads ‘lock’ in the middle of layers of the fabric you are sewing.

Singer Sewing Machine (7258) — STRAIGHT STITCHING diagram (page 30)
Fig. 14

If, when you start to sew, you find that the stitching is irregular, you will need to adjust the tension control.

Make any adjustments with presser foot ‘down’.

A balanced tension (identical stitches both top and bottom) is usually only desirable for straight stitch sewing.

Top stitch too tight Fil supérieur trop tendu

Top stitch too loose Fil supérieur trop lâche

Puntada superior demasiado apretada

ZIG ZAG and DECORATIVE SEWING

For zigzag sewing and decorative stitch functions, thread ten- sion should be less than for straight stitch sewing.

You will always obtain a nicer stitch and less puckering when the upper thread appears on the bottom side of your fabric.

Decrease tension Diminuer la tension

Increase tension Augmenter la tension

BOBBIN TENSION

The bobbin tension has been correctly set at the factory, so you do not need to adjust it.

CHANGING PRESSER FOOT

Presser foot lifter Levier de verrouillage du pied Palanca pie prensatelas

Be sure needle is in the up position. Raise presser foot lifter.

1. Push presser foot release lever to remove the foot.
3. Lower the presser foot lifter so that the foot holder snaps on the foot. 1 3
2. Place the desired foot on the needle plate aligning the presser foot pin with the foot holder.

Levier de verrouillage du pied

Palanca de desprendimiento prensatelas

Foot holder Support du pied Sujetador prensatelas

Show 5 more labels / short text on this page
Puntada superior · demasiado floja · Disminuir tensión · Aumentar tensión · Foot release lever
Page 31 of the Singer Sewing Machine (7258) user manual — REMPLACEMENT DU PIED PRESSEUR
Page 31 · click to enlarge
Page 31

RÉGLAGE DE LA TENSION DU FIL SUPÉRIEUR 90% de votre couture sera accomplie avec le cadran de réglage de tension (en haut de la machine) réglé à “Auto” .

AJUSTE DE LA TENSION DEL HILO SUPERIOR El 90% de tu costura se hará con el control de tensión establecido en “AUTO” (arriba de la máquina).

Suggestion utile: Un léger ajustement sur le côté + ou – de AUTO améliorera l’apparence de la couture.

POINT DROIT

COSTURA RECTA

Une belle apparence de votre point est grandement influencé par le bon équilibre entre le fil de la bobine et le fil de la tension supérieur. Elle est parfaite lorsque les deux fils se nouent entre les deux épaisseurs de tissu.

La apariencia correcta de tu costura es ampliamente determinada por la tensión equilibrada de ambos hilos, el superior y el de la bobina.

Si se encuentra que la costura es irregular, se necesitará ajustar el control de la tensión. Cualquier ajuste se ha de realizar con el pie prensatelas abajo.

Vous pouvez régler la tension supérieure avec le cadran de réglage de tension. Si la tension supérieure est trop lâche, tourner le cadran vers le haut pour l’augmenter. Si elle est trop forte, tournez-la vers l’autre côté pour la diminuer.

Una tensión balanceada (puntadas idénticas arriba y abajo) normalmente es lo deseado para costura de puntadas rectas.

Une tension équilibrée (points supérieurs et inférieurs identiques) n’est généralement désirable que pour la couture de points droits.

COUTURE ZIGZAG ET DÉCORATIVE

COSTURA ZIG ZAG y DECORATIVA

Pour les fonctions de couture zigzag et décorative, la tension du fil doit être inférieure à celle pour la couture de points droits.

Para las funciones de costura zigzag y decorativa, la tensión de hilo debe ser menor que para costura de puntadas rectas.

Les points seront toujours meilleurs avec moins de fronces lorsque le fil supérieur apparaît du côté inférieur du tissu.

Siempre deberá obtener una costura bonita y menos arrugas cuando el hilo superior aparece del lado de debajo de su tejido.

TENSION DE LA CANETTE

TENSIÓN BOBINA

La tension de la canette a été correctement réglée à l'usine, il est inutile de la corriger.

Esta ha sido ajustada correctamente en fábrica por lo que no es necesario realizar ningún ajuste.

REMPLACEMENT DU PIED PRESSEUR

CAMBIO DEL PIE PRENSATELAS

Relevez l’aiguille au maximum, ainsi que le levier du pied presseur.

Asegurarse de que la aguja está en la posición más alta. Alzar la palanca del pie prensatelas.

1. Poussez le levier de verrouillage et enlever le pied.
1. Oprimir la palanca de desprendimiento del prensatelas para sacar el prensatelas.
2. Placez le pied choisie sur la plaque-aiguille comme illustré.
2. Colocar el prensatelas deseado sobre la placa aguja, alineando los agujeros aguja.
3. Rabaissez le levier du pied presseur de façon à ce que le pied s’enclenche de lui-même sur son support.
3. Bajar la palanca pie prensatelas, de manera que el sujetador prensatelas se cierre de golpe en el prensatelas.
Page 32 of the Singer Sewing Machine (7258) user manual — FUNCTIONS OF CONTROL PANEL
Page 32 · click to enlarge
Page 32

Stitch width/needle position of straight stitch Largeur du point/position de l’aiguille sur le point droit Ancho de puntada/posición de aguja en costura recta

Stitch length Longueur du point Largo de puntada

LCD display Écrans ECL Pantalla LCD

Stitch pattern number Numéro du point motif Número de patrón de puntada

Manual adjustment buttons for stitch width/needle position Boutons d’ajustement manuel de la largeur du point et de la position d’aiguille Ajuste manual de botones para ancho de puntada/posición de aguja

Buttons for pattern number selection Boutons pour sélectionner le numéro du point motif Botones para elegir número de puntada

Manual adjustment buttons for stitch length Boutons d’ajustement manuel de la longueur du point Ajuste manual botones para largo de puntada

Pattern number reference guide Guide de référence du numéro des motifs Guía de referencia del número de puntada

FUNCTIONS OF CONTROL PANEL

PATTERN NUMBER SELECTION BUTTONS When the machine is turned on, straight stitch is selected and pop-up screen for individual preference settings appears on the LCD display.

Singer Sewing Machine (7258) — FUNCTIONS OF CONTROL PANEL diagram (page 32)
Fig. 15

Buttons for pattern number selection Boutons pour sélectionner le numéro du point motif Botones para elegir número de puntada

To select stitch patterns, use left button for pattern number selection to select left digit and right button to select right digit referring to pattern number reference guide.

Both left and right digits scroll up to 9.

STITCH LENGTH AND STITCH WIDTH/NEEDLE POSITION ADJUSTMENT BUTTONS Your sewing machine will produce your stitching requirements at an Auto/Default stitch Length and Width.

Singer Sewing Machine (7258) — FUNCTIONS OF CONTROL PANEL diagram (page 32)
Fig. 16

Manual adjustment buttons for stitch length Boutons d’ajustement manuel de la longueur du point Ajuste manual botones para largo de puntada

Default settings of stitch length and width are underlined on the display.

You can manually change the length, width or needle position for straight stitch according to your preference pushing manual adjustment buttons.

Singer Sewing Machine (7258) — FUNCTIONS OF CONTROL PANEL diagram (page 32)
Fig. 17

Manual adjustment buttons for stitch width/needle position Boutons d’ajustement manuel de la largeur du point et de la position d’aiguille Ajuste manual de botones para ancho de puntada/posición de aguja

Page 33 of the Singer Sewing Machine (7258) user manual — FONCTIONS DU PANNEAU DE COMMANDE
Page 33 · click to enlarge
Page 33

FONCTIONS DU PANNEAU DE COMMANDE

FUNCIONES DE PANEL DE CONTROL

BOTONES PARA ELEGIR NUMERO DE PUNTADA Cuando la máquina está encendida, se selecciona costura recta y aparecen en la pantalla de LCD los ajustes para personalizar las opciones.

BOUTON DE SÉLECTION DES NUMÉROS DES MOTIFS Lorsque la machine est mise en fonction, le point droit est sélectionné et les réglages individuel sont illustrés sur l’écran ECL.

Para elegir patrones de puntada, usar el botón izquierdo para seleccionar el número de patrón para elegir el dígito izquierdo, y botón derecho para elegir el dígito derecho referente al número de guía de patrón.

Pour sélectionner les motifs, utilisé le bouton du coté gauche pour sélectionner le chiffre de gauche et le bouton du coté droit pour sélectionner le chiffre de droite, en vous référant au guide de référence des motifs.

Ambos dígitos (izquierda y derecha) recorren hasta el 9.

Les chiffres de gauches et de droites défilent jusqu’à 9.

BOUTONS D’AJUSTEMENT DE LA LONGEUR ET DE LA LARGEUR DU POINT/POSITION D’AIGUILLE Votre machine à coudre exécutera un motif sélectionner à une longueur et une largeur Automatique/par Défaut.

BOTONES DE AJUSTE DE LARGO Y ANCHO DE PUNTADA/POSICIÓN DE AGUJA Su máquina ajustará Automáticamente/Por Omisión, sus requerimientos de Largo y Ancho de Puntada.

Les réglages automatiques par défaut de la longueur et de la largeur du point apparaissant sur l’écran sont souligner.

Los ajustes pre-establecidos de largo y ancho de puntada están subrayados en pantalla.

Vous pouvez changer manuellement la longueur et la largeur du point ou la position de l’aiguille, du point droit, selon vos préférences en appuyant sur les boutons d’ajustement manuel.

Usted puede cambiar manualmente el largo y ancho de puntada o posición de la aguja para la puntada recta de acuerdo a su preferencia, oprimiendo los botones de ajuste manual.

Page 34 of the Singer Sewing Machine (7258) user manual — HELPFUL MESSAGES
Page 34 · click to enlarge
Page 34

HELPFUL MESSAGES

If an incorrect operation is made, a helpful message will be displayed. When a helpful message is displayed, fix the problem following the instructions below.

Bobbin winder is moved to right (operating position) during sewing. Check bobbin winder and move it to left.

Buttonhole lever is not lowered or raised. Lower buttonhole lever when sewing buttonholes. Raise buttonhole lever when sewing stitch patterns.

Foot control plug is pulled out, while operating foot control. Push in foot control plug.

Machine is locked up due to thread entangled with bobbin case or rotation interrupted forcibly. Turn off power switch and eliminate the problem that caused the machine

to stop.

Reverse/tacking stitch button is pushed, while buttonhole stitch is selected. Tacking stitch is made automatically after buttonhole stitch is completed. It is not necessary to push the reverse/tacking stitch button.

Bobbin winder is in operation. Move bobbin winder to left when it is not used.

Page 36 of the Singer Sewing Machine (7258) user manual — DUAL PURPOSE REVERSE/TACKING STITCH BUTTON
Page 36 · click to enlarge
Page 36
Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 36)
Fig. 18 · 7258 Instruction Manual_cover

Reverse stitch button Bouton du point de marche arrière Botón de puntada hacia atrás

Programmable needle up/down button Touche de position d’arrêt d’aiguille Nterruptor de posicion de aguja parada

When sewing without having the foot controller connected, the machine starts slowly when the start/stop button is pushed. When it is pushed again, needle moves and stops at its highest position.

When using foot control, simply press foot pedal with your foot until you reach a slow even speed. The harder you push, the faster the machine will sew. Release pressure on foot pedal to stop the machine.

Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 36)
Fig. 19 · 7258 Instruction Manual_cover

Push the switch and LED lamp will be lit red and needle will stop at down position whenever you stop sewing.

Push it again to stop needle at up position.

DUAL PURPOSE REVERSE/TACKING STITCH BUTTON

Singer Sewing Machine (7258) — DUAL PURPOSE REVERSE/TACKING STITCH BUTTON diagram (page 36)
Fig. 20

* Reverse stitch function for straight and zigzag stitches ( ) Reverse sewing is carried out while the reverse stitch button

is pushed.

The machine will continue to sew in reverse as long as the

reverse button is pressed.

* Tacking stitch function for tie-off of other stitches ( ) The sewing machine makes 4 tiny tacking stitches to tie

off the sewing on all patterns except straight, zigzag and buttonhole stitches. The position of the tacking stitches will be at the exact spot in the pattern where the reverse/tacking stitch button is pushed.

Page 38 of the Singer Sewing Machine (7258) user manual — SEWING SPEED CONTROL
Page 38 · click to enlarge
Page 38

Sewing speed control Régulateur de vitesse Control de velocidad de costura

SEWING SPEED CONTROL

Sewing speed is set by using the sewing speed control. The sewing speed control is moved horizontally to determine the amount of speed required.

Regardless of the setting, maximum speed may be limited depending on which pattern has been selected.

Page 40 of the Singer Sewing Machine (7258) user manual — 2. STARTING TO SEW QUICK REFERENCE TABLE OF STITCH LENGTH AND WIDTH
Page 40 · click to enlarge
Page 40
Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 40)
Fig. 21 · 7258 Instruction Manual_cover

2. STARTING TO SEW QUICK REFERENCE TABLE OF STITCH LENGTH AND WIDTH

2. COMMENCEZ À COUDRE TABLEAU DE RÉFÉRENCE RAPIDE DES LONGUEURS ET LARGEURS DE POINTS
2. EMPEZER A COSER CUADRO DE REFERENCIA RÁPIDA DE LARGO Y ANCHO DE PUNTADA

LEFT - RIGHT GAUCHE - DROIT IZQUIERDA - DERECHA 2.5 0.5 - 4.8

03 5.0 0 - 6.0 2.0 0 - 3.0 07 3.0 1.0 - 6.0 2.0 1.0 - 3.0

04 3.0 2.0 - 7.0 2.0 1.0 - 3.0 08 3.0 1.0 - 6.0 2.0 1.0 - 3.0

05 3.0 2.0 - 7.0 2.0 1.0 - 3.0 09 6.0 3.0 - 6.0 2.0 1.5 - 3.0

06 6.0 2.5 - 6.0 1.5 0 - 2.5 10 5.5 3.5 - 7.0 2.5 1.5 - 3.0

Page 41 of the Singer Sewing Machine (7258) user manual — 21 7.0 1.0 - 7.0 2.5 1.5 - 3.0 36 6.0 -
Page 41 · click to enlarge
Page 41

TWIN NEEDLE* AIGUILLE DOUBLE*

TWIN NEEDLE* AIGUILLE DOUBLE*

STITCH

No.

STITCH

No.

ANCHO

LARGO

ANCHO

LARGO

POINT

No.

POINT

No.

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

PUNTADA

No.

DOS AGUJAS*

PUNTADA

No.

AGUJA DOBLE*

11 5.5 3.5 - 7.0 2.5 1.5 - 3.0 26 6.0 3.5 - 7.0 2.5 1.5 - 2.5

12 6.0 3.0 - 6.0 2.0 1.0 - 3.0 27 6.0 2.0 - 6.0 2.5 1.0 - 3.0

13 5.0 2.0 - 6.0 2.5 1.5 - 3.0 28 6.0 2.0 - 7.0 2.5 1.0 - 2.5

14 5.5 3.5 - 7.0 2.5 1.5 - 3.0 29 7.0 3.5 - 7.0 2.5 1.3 - 3.0

15 6.0 3.0 - 6.0 2.0 1.5 - 3.0 30 7.0 3.0 - 7.0 1.8 1.5 - 2.5

16 5.0 2.0 - 7.0 2.5 1.5 - 3.0 31 1.0 - 2.5 1.5 - 3.0

17 5.0 1.0 - 7.0 2.5 1.5 - 3.0 32 5.0 5.0, 6.0 3.0 -

18 5.0 1.0 - 7.0 2.5 1.5 - 3.0 33 6.5 3.5 - 7.0 2.5 1.5 - 2.5

19 5.0 1.0 - 7.0 2.5 1.5 - 3.0 34 5.5 3.0 - 7.0 2.5 1.5 - 2.5

20 7.0 1.0 - 7.0 2.5 1.5 - 3.0 35 5.0 1.0 - 7.0 2.5 0.8 - 2.5

21 7.0 1.0 - 7.0 2.5 1.5 - 3.0 36 6.0 -

22 5.0 1.0 - 6.0 2.0 0.8 - 2.5 37 7.0 3.5 - 7.0 0.8 0.5 - 1.5

23 5.0 1.0 - 6.0 2.0 0.8 - 2.5 38 7.0 3.5 - 7.0 0.8 0.5 - 1.5

24 5.0 1.0 - 7.0 2.0 1.0 - 3.0 39 7.0 3.5 - 7.0 0.5 0.3 - 1.5

25 5.0 1.0 - 7.0 2.0 1.0 - 3.0 40 7.0 3.5 - 7.0 0.5 0.3 - 1.5

Show 5 more labels / short text on this page
WIDTH LARGEUR (mm) · LENGTH LONGUEUR (mm) · WIDTH LARGEUR (mm) · LENGTH LONGUEUR (mm) · Varied Variées Variado
Page 42 of the Singer Sewing Machine (7258) user manual — AGUJA DOBLE*
Page 42 · click to enlarge
Page 42

TWIN NEEDLE* AIGUILLE DOUBLE*

TWIN NEEDLE* AIGUILLE DOUBLE*

STITCH

No.

STITCH

No.

ANCHO

LARGO

ANCHO

LARGO

POINT

No.

POINT

No.

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

PUNTADA

No.

DOS AGUJAS*

PUNTADA

No.

AGUJA DOBLE*

41 7.0 3.5 - 7.0 0.5 0.3 - 1.5 56 7.0 3.5 - 7.0 0.5 0.3 - 1.5

42 7.0 3.5 - 7.0 0.5 0.3 - 1.5 57 7.0 3.0 - 7.0 0.5 0.3 - 1.5

43 7.0 3.5 - 7.0 0.5 0.3 - 1.5 58 6.0 3.0 - 6.0 0.5 0.3 - 1.3

44 7.0 3.5 - 7.0 0.5 0.3 - 1.5 59 5.0 2.0 - 6.0 0.5 0.5 - 1.0

45 7.0 3.5 - 7.0 0.5 0.3 - 1.5 60 5.0 2.0 - 7.0 0.5 0.5, 0.8

46 7.0 3.5 - 7.0 0.5 0.3 - 1.5 61 7.0 3.5, 7.0 2.0 1.5 - 2.5

47 7.0 3.0 - 7.0 0.5 0.3 - 1.5 62 7.0 3.5 - 7.0 2.5 1.5 - 2.5

48 7.0 3.0 - 7.0 0.5 0.3 - 1.5 63 7.0 3.5, 7.0 1.8 0.8 - 2.5

49 7.0 3.0 - 7.0 0.5 0.3 - 1.5 64 6.0 3.5, 6.0 Varied Variées Variado -

50 7.0 3.0 - 7.0 0.5 0.3 - 1.5 65 6.0 3.5, 6.0 Varied Variées Variado -

51 7.0 3.0 - 7.0 0.5 0.3 - 1.5 66 7.0 3.5 - 7.0 1.3 0.8 - 4.0

52 7.0 3.5 - 7.0 0.5 0.3 - 1.5 67 7.0 3.5 - 7.0 1.3 0.8 - 4.0

53 7.0 3.0 - 7.0 0.5 0.3 - 3.0 68 7.0 3.5 - 7.0 1.8 1.0 - 4.0

54 7.0 3.0 - 7.0 0.5 0.3 - 3.0 69 7.0 3.5 - 7.0 1.8 1.0 - 4.0

55 7.0 3.5 - 7.0 0.5 0.3 - 2.5 70 7.0 3.0 - 7.0 2.5 1.0 - 2.5

Show 4 more labels / short text on this page
WIDTH LARGEUR (mm) · LENGTH LONGUEUR (mm) · WIDTH LARGEUR (mm) · LENGTH LONGUEUR (mm)
Page 43 of the Singer Sewing Machine (7258) user manual — AGUJA DOBLE*
Page 43 · click to enlarge
Page 43

TWIN NEEDLE* AIGUILLE DOUBLE*

TWIN NEEDLE* AIGUILLE DOUBLE*

STITCH

No.

STITCH

No.

ANCHO

LARGO

ANCHO

LARGO

POINT

No.

POINT

No.

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

AUTO AUTO AUTO

MANUAL MANUEL MANUAL

PUNTADA

No.

DOS AGUJAS*

PUNTADA

No.

AGUJA DOBLE*

71 7.0 3.0 - 7.0 2.5 1.0 - 2.5 86 7.0 3.0 - 7.0 2.5 1.5 - 2.5

72 6.0 3.0 - 6.0 2.5 1.5 - 2.5 87 7.0 4.0 - 7.0 2.5 1.5 - 2.5

73 6.0 3.0 - 6.0 2.5 1.5 - 2.5 88 6.0 2.0 - 7.0 1.5 0.5 - 2.0

74 6.0 3.0 - 6.0 2.5 1.5 - 2.5 89 3.5 - 2.0 2.0 - 4.0

75 6.0 3.0 - 6.0 2.5 1.5 - 2.5 90 3.0 2.0 - 4.5 0 -

76 7.0 3.5 - 7.0 2.5 1.5 - 2.5 91 6.0 - 0.5 0.5, 0.8

77 7.0 3.5 - 7.0 2.5 1.5 - 2.5 92 -

78 5.0 3.0 - 7.0 2.5 1.5 - 2.5 93 6.0 - 0.5 0.5, 0.8

79 5.0 3.0 - 7.0 2.5 1.5 - 2.5 94 5.5 - 0.5 0.5, 0.8

80 6.0 3.0 - 7.0 2.0 1.0 - 2.5 95 3.5 - 0.5 0.5, 0.8

81 5.0 3.5 - 7.0 2.5 1.5 - 2.5 96 5.5 - 0.5 0.5, 0.8

82 6.0 3.0 - 6.0 2.5 1.5 - 2.5 97 3.5 - 0.5 0.5, 0.8

83 7.0 3.5 - 7.0 2.5 1.5 - 2.5 98 5.5 - 0.5 0.5, 0.8

84 7.0 3.5 - 7.0 2.5 1.5 - 2.5 99 3.5 - 0.5 0.5, 0.8

85 6.3 3.8 - 6.3 1.3 1.0 - 2.0

* Whenever using twin needle, set stitch width at 3.5 or less. * Lorsque vous utilisez des aiguilles jumelées, régler la largeur du point à 3.5 ou moins. * Cuando se use aguja doble, fije el ancho de puntada a un valor 3.5 o menor.

Show 4 more labels / short text on this page
WIDTH LARGEUR (mm) · LENGTH LONGUEUR (mm) · WIDTH LARGEUR (mm) · LENGTH LONGUEUR (mm)
Page 44 of the Singer Sewing Machine (7258) user manual — KEEPING SEAMS STRAIGHT
Page 44 · click to enlarge
Page 44

STRAIGHT STITCHING

A

Straight stitch is most frequently used for all types of sewing. Let’s begin by following the steps below.

B C D

1. SETTINGS Presser foot - General Purpose Foot Thread tension control - AUTO

E F

A. Thread tension control B. Reverse stitch button C. Programmable needle up/down button D. Start/stop button E. Presser foot lifter F. Sewing speed control

2. Pull both threads under the presser foot toward the back of the machine, leaving about 6” (15cm) clear.
3. Place the fabric under the presser foot and lower the presser foot lifter.
4. Turn the hand wheel toward you (counter-clockwise) until the needle enters the fabric.
5. Start the machine. Guide the fabric gently with your hands. When reaching the edge of the material, stop the sewing machine.
6. First turn the handwheel toward you (counter-clockwise) until the needle is at its highest position. Raise the presser foot, draw materials to the rear and cut off excess thread with the thread cutter located on the bottom of face cover as shown.

KEEPING SEAMS STRAIGHT

To keep the seam straight, use one of the numbered guide lines on the needle plate. The numbers indicate distance from the needle at its center position.

The guide line on the bobbin cover plate is 1/4" (6mm) seam guide line which is used for piecing quilt blocks and also for narrow seams.

3/4" (19 mm)

5/8" (16 mm)

1/2" (13 mm)

3/8" ( 9 mm)

1/4" ( 6 mm)

Page 45 of the Singer Sewing Machine (7258) user manual — POUR GARDER LA COUTURE DROITE
Page 45 · click to enlarge
Page 45

POINT DROIT

PUNTADA RECTA

Ceci est le point le plus utilisé pour toute genre de couture. Apprenez à vous servir correctement de votre machine, en suivant les étapes ci-dessous.

La puntada recta se usa más frecuentemente para coser todo tipos de costura. Comencemos siguiendo los pasos abajo.

1. AJUSTES Pie prensatelas - Pie universal Control tensión hilo - AUTO
1. RÉGLAGES Pied de biche - Pied universel Réglage tension du fil supérieur - AUTO

A. Réglage tension du fil supérieur B. Touche couture arrière C. Bouton d’arrêt de la position d’aiguille D. Bouton de marche/arrêt E. Levier du pied presseur F. Régulateur de vitesse

A. Control tensión hilo B. Botón de puntadas hacia atrás C. Botón de posición de aguja detenida D. Botón inicio/parada E. Palanca pie prensatelas F. Control de velocidad de costura

2. Tirez les deux fils sous le pied presseur vers l’arrière de la machine, en laissant environ 15 cm de fil.
2. Tire de ambos hilos debajo del prensatelas hacia atrás de la máquina, dejando una separación de 6 pulg. (15 cm).
3. Placer le tissu sous le pied presseur et abaisser le pied.
3. Colocar la tela debajo del prensatelas y bajar la palanca del prensatelas.
4. Tourner le volant vers vous jusqu’à ce que l’aiguille pénètre dans le tissu.
4. Girar el volante hacia Ud. hasta que la aguja entre en el material.
5. Démarrez la machine. Guidez le tissu légèrement avec la main. Lorsque vous arrivez au bord du tissu, arrêtez la machine à coudre.
5. Arranque la máquina. Guíe el material suavemente con sus manos. Al llegar al borde del material, pare la máquina de coser.
6. Tourner d’abord le volant vers soi jusqu’à ce que l’aiguille arrive à sa position la plus haute, puis relever le pied presseur, tirer le tissu vers l’arrière et couper la longueur de fil excessive au moyen du coupe fil placé au bas de la plaque frontale, comme indiqué sur l’illustration.
6. Primero girar el volante hacia usted, hasta que la aguja esté en el punto máximo superior. Levantar el pie prensatelas, llevar el tejido hacia atrás y cortar el exceso de hilo con el cortador de hilo que está colocado en la parte lateral de la máquina, según está mostrado.

POUR GARDER LA COUTURE DROITE

MANTENIENDO LA PUNTADA DERECHA

Pour piquer une ligne droite, utiliser les lignes de guide sur la plaque à aiguille. Le numéro indiqué est la distance entre l’aiguille au centre et la ligne sur la plaque.

Para mantener la puntada derecha, utilice una de las líneas guía numeradas en la placa aguja. Los números indican la distancia desde la aguja hacia la posición central de la misma.

La ligne guide sur la plaque couvre bobine est pour une couture de ¼ de pouce (6mm), pour le matelassage et pour les coutures étroites.

La guía sobre la placa aguja es de 1/4” (6mm) de costura la cual se usa para acolchados y también para costuras estrechas.

Page 46 of the Singer Sewing Machine (7258) user manual — INSERTING ZIPPERS AND PIPING
Page 46 · click to enlarge
Page 46

STRAIGHT STITCH WITH AUTO TIE-OFF FUNCTION 1. Press the foot control and the machine will sew 4 stitches in forward and then 4 stitches in reverse and continue to sew in forward until the foot control is released.

2. Push the reverse switch and the machine will sew 4 stitches in reverse and then 4 stitches in forward and stop.

INSERTING ZIPPERS AND PIPING

Use zipper foot to sew to the right or left of the zipper or close to the cording.

Needle to left of foot Aiguille à gauche du pied presseur

Needle to right of foot Aiguille à droite du pied presseur

Aguja a la izquierda del prensatelas

Aguja a la derecha del prensatelas

INSERTING ZIPPERS To sew down the right side, attach left side of zipper foot to presser foot holder so that the needle passes through the opening on the left side of the foot.

To sew down the left side, attach right side of foot to foot holder.

PIPING To pipe soft furnishings, cover cord with a bias strip of fabric and pin or tack it to the main piece of fabric.

Attach left side of zipper foot to foot holder so that needle passes through the opening on the left side of the foot.

Helpful Hint: Slight adjusting of the needle position to sew closer to the piping may be accomplished with the Stitch Width Control.

Page 48 of the Singer Sewing Machine (7258) user manual — PLACEMENT OF PATTERNS
Page 48 · click to enlarge
Page 48

ZIGZAG STITCHING

Under side Côté de dessous Reverso

SETTINGS :Presser foot - General Purpose Foot :Thread tension control - AUTO

Singer Sewing Machine (7258) — ZIGZAG STITCHING diagram (page 48)
Fig. 22

The top thread may appear on the bottom depending on the thread, fabric, type of stitch and sewing speed, but the bobbin thread must never appear on the top of the fabric.

If bobbin thread is pulling to the top or you are experiencing puckering, slightly reduce the tension with the Thread Tension Control.

Top side Côté de dessus Cara

ADJUSTING STITCH WIDTH AND LENGTH

Dark grey box indicates the Auto/default value set automatically when the pattern is selected. For the Zigzag Pattern the stitch length is 2 mm and the stitch width is 5 mm.

STITCH WIDTH LARGEUR DU POINT

ANCHO PUNTADA

mm 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

The light grey boxes indicate all the possible personal preference options available to set manualy.

LONGUEUR DU POINT

STITCH LENGTH

LARGO PUNTADA

SATIN STITCH

Singer Sewing Machine (7258) — LONGUEUR DU POINT diagram (page 48)
Fig. 23

This is a closely spaced stitch for appliqué, bar-tacking, etc. Slightly loosen the top thread tension and manually adjust the stitch length between 0.5 and 2.0 for satin stitching. Use a backing of stabilizer or interfacing to avoid puckering.

PLACEMENT OF PATTERNS

Center position Position centrale Aguja posicionada en el centro

The satin stitch increases from the center needle position; making it possible to create center tapered stitch, as illustrated.

Page 49 of the Singer Sewing Machine (7258) user manual — POSITIONNEMENT DES MOTIFS
Page 49 · click to enlarge
Page 49
Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 49)
Fig. 24 · 7258 Instruction Manual_cover
Singer Sewing Machine (7258) — 7258 Instruction Manual_cover diagram (page 49)
Fig. 25 · 7258 Instruction Manual_cover

POINT ZIGZAG

PUNTADA ZIG-ZAG

RÉGLAGES :Pied presseur - Pied universel :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Pie universal :Control tensión hilo - AUTO

Le fil supérieur peut paraître sur l’envers, en fonction du fil, du tissu et de la vitesse de couture, mais le fil de la canette ne doit jamais paraître sur l’endroit.

El hilo superior puede aparecer en la parte inferior, según el hilo, tejido, tipo de puntada y velocidad de costura, pero el hilo de la bobina nunca deberá aparecer en la parte superior del tejido.

Si le fil de la canette tire vers le haut ou si des fronces se produisent, réduisez légèrement la tension à l’aide de la commande de tension du fil.

Si el hilo de la bobina está tirando hacia arriba o si tiene problemas con la formación de arrugas, reduzca ligeramente la tensión con el control de tensión de hilo.

RÉGLAGE DE LA LARGEUR ET DE LA LONGUEUR DE POINT

AJUSTE DEL ANCHO Y LARGO DE PUNTADA

Une case gris foncé indique la valeur automatique/par défaut réglée automatiquement lors de la sélection du motif. Pour le motif zigzag, la longueur du point est de 2 mm et la largeur du point est de 5 mm.

La casilla gris oscuro indica el valor automático/ por defecto ajustado automáticamente cuando se selecciona el patrón. Para el patrón de zigzag el largo de puntada es 2 mm y el ancho de puntada es 5 mm.

La case gris clair indique toutes les options de préférences personnelles disponibles pouvant être réglées manuellement.

La casilla gris clara indica todas las opciones de preferencia personal disponibles para ajustar manualmente.

POINT BOURDON

PUNTADA DE RELLENO

Ceci est un point très rapprocher pour appliqué et bride, etc. Lorsque vous utilisez ce point, pensez à diminuer la tension supérieure. Régler la longueur de point entre 0.5 et 2.0. Plus le point est large, plus la tension doit être diminuée. Utiliser un entoilage pour éviter les fronces.

Esta es una puntada compactamente espaciada para aplicaciones, remates, etc. Para la puntada de relleno aflojar ligeramente la tensión del hilo superior. Usar un estabilizador o cubierta para evitar fruncidos.

POSITIONNEMENT DES MOTIFS

UBICACION DE LOS PATRONES

La largeur du point bourdon augmente par rapport à la position de l’aiguille centrale; pour créer un centre effilé comme illustrée.

La puntada de satín aumenta cuando la aguja está posicionada al centro; posibilitando crear una puntada delgada, como se muestra.

Page 50 of the Singer Sewing Machine (7258) user manual — A
Page 50 · click to enlarge
Page 50

BLINDHEM STITCH

The blindhem stitch is primarily used for creating nearly invisible hems on curtains, trousers, skirts, etc.

Medium to heavyweight fabric Material de peso medio a pesado Tissus moyens et lourds

SettingsPresser foot - Blind stitch foot : Thread Tension Control: AUTO
Singer Sewing Machine (7258) — BLINDHEM STITCH diagram (page 50)
Fig. 26
Singer Sewing Machine (7258) — BLINDHEM STITCH diagram (page 50)
Fig. 27

- Regular blind stitch for normal woven fabrics

- Elastic blind stitch for soft, stretchable fabrics

Under side Reverso Envers

Under side Reverso Envers

1. With matching thread finish the raw edge. On fine fabric turn up and press a small ½” or less hem. On medium to heavyweight fabrics overcast the fabric’s raw edge.

Fine fabric Material fino Tissus fins

Singer Sewing Machine (7258) — - Regular blind stitch for normal woven fabrics diagram (page 50)
Fig. 28 · - Regular blind stitch for normal woven fabrics
2. Now fold the fabric as illustrated with the wrong side up.

Under side Reverso Envers

Under side Reverso Envers

Singer Sewing Machine (7258) — - Regular blind stitch for normal woven fabrics diagram (page 50)
Fig. 29 · - Regular blind stitch for normal woven fabrics

B

3. Place the fabric under the foot. Turn the handwheel towards you (counter-clockwise) by hand until the needle swings fully to the left. It should just pierce the fold of the fabric. If it does not, adjust the guide (B) on the Blindhem Foot (A) so that the needle just pierces the fabric fold and the guide just rests against the fold.

A

Singer Sewing Machine (7258) — A diagram (page 50)
Fig. 30

Sew slowly, guiding the fabric carefully along the edge of the guide.

Singer Sewing Machine (7258) — A diagram (page 50)
Fig. 31
4. When completed, the stitching is almost invisible on the right side of the fabric.

Top side Cara Endroit

Page 51 of the Singer Sewing Machine (7258) user manual — - Point invisible pour les tissus extensibles
Page 51 · click to enlarge
Page 51

POINT INVISIBLE

PUNTADA INVISIBLE

RÉGLAGES :Pied presseur - Pied point invisible :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Prensatelas de puntada invisible :Control tensión hilo - AUTO

- Point ourlet invisible régulier pour tissu tissé

Puntada Invisible Regular para tela de lana normal

Puntada invisible super elástico para las telas suves, elástico

- Point invisible pour les tissus extensibles

1. D’abord surfiler les bords avec un zigzag, ensuite plier l’ourlet sur la largeur désirée et repasser.
1. Primero terminar el borde. Para esto, doblarlo sobre el material fino y sobreorillarlo sobre el material de peso medio pesado. Entonces doblarlo según la profundidad y presión necesarias.
2. Maintenant, pliez le tissu comme indiqué dans l’illustration avec l’envers tournée vers le haut.
2. Ahora doble el material tal como está ilustrado con el reverso hacia arriba.
3. Placez le tissu sous le pied. Faites tourner le volant vers vous à la main jusqu’à ce que l’aiguille aille complètement vers la gauche. Elle ne devrait percer que le pli du tissu. Si elle ne le fait pas, ajustez le guide (B) du pied invisible (A) de façon à ce que l’aiguille ne perce que le pli du tissu et que le guide repose juste sur le pli.
3. Coloque el material debajo del pie. Gire el volante hacia usted a mano hasta que la aguja se mueva completamente hacia la izquierda. Deberá solo atravesar el pliegue del material. De lo contrario, ajuste la guía (B) en el pie de puntada invisible (A) de manera que la aguja solo atraviese el pliegue del material y la guía solo descanse contra el pliegue.
Singer Sewing Machine (7258) — - Point invisible pour les tissus extensibles diagram (page 51)
Fig. 32 · - Point invisible pour les tissus extensibles
Singer Sewing Machine (7258) — - Point invisible pour les tissus extensibles diagram (page 51)
Fig. 33 · - Point invisible pour les tissus extensibles

Effectuez la couture lentement, tout en guidant soigneusement le tissu le long du bord du guide.

Cosa lentamente, guiando el material cuidadosamente a lo largo del borde de la guía.

4. Lorsque l’ourlet est terminé, les points sont presque invisibles sur l’endroit du tissu.
4. Una vez terminado, los puntos son casi invisibles sobre el lado derecho del material.
Page 52 of the Singer Sewing Machine (7258) user manual — SEWING ON A BUTTON
Page 52 · click to enlarge
Page 52

MULTI-STITCH ZIGZAG

Singer Sewing Machine (7258) — MULTI-STITCH ZIGZAG diagram (page 52)
Fig. 34

SETTINGS :Presser foot - General Purpose Foot :Thread tension control - AUTO

This is a strong stitch because as its name implies, it makes three short stitches where the normal zig-zag makes only one.

For this reason it is recommended for overcasting all types of fabrics.

It is also ideal for bartacks, mending tears, patching, and attaching flat elastic.

SHELL STITCH

SETTINGS :Presser foot - General Purpose Foot :Thread tension control - AUTO

Turn under the raw edge and press. Place the fabric right side up so that the zigzag part of the stitch sews just over the folded edge, pulling the fabric in to form a shell hem. Trim away excess fabric from the backside, close to the stitching line.

Helpful Hint: For a pleasing appearance experiment with different width, length and tension settings.

SEWING ON A BUTTON

SETTINGS :Presser foot - General purpose foot :Darning plate

Position your fabric and button under the presser foot. Lower presser foot. Turn the handwheel to make sure needle clears both left and right openings of button. Adjust width if required. Sew 10 stitches.

If a button shank is required, place a darning needle on top of the button and sew over top of it as illustrated.

Helpful Hint: To secure thread, pull both threads to the backside of the fabric and tie together.

Singer Sewing Machine (7258) — SEWING ON A BUTTON diagram (page 52)
Fig. 35
Page 53 of the Singer Sewing Machine (7258) user manual — POSE DE BOUTONS
Page 53 · click to enlarge
Page 53

ZIGZAG MULTI-POINT

ZIG-ZAG DE TRES PUNTADAS

RÉGLAGES :Pied presseur - Pied universel :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Pie universal :Control tensión hilo - AUTO

Pour réparer des déchirures droites ou en angle placez le tissu avec le début de l’accroc sous la partie centrale du pied. Lorsque vous avez un accroc en deux parties, reprisez à partir de chaque extrèmité pour revenir au centre.

Esta es una puntada fuerte, ya que como su nombre implica, realiza tres puntadas cortas donde el zig-zag normal sólo realiza una.

Por esta razón se recomienda sobrehilar todo tipo de telas.

Pour cette raison, il est recommandé pour surjeter tous genres de tissus.

También es ideal para remates, zurcidos, parches, y pegado de elásticos.

Il est aussi recommande pour des brides, du raccommodage, du reprisage et pour la pose d’élastique plat.

POINT DE LINGERIE

PUNTADA DE LENCERIA

RÉGLAGES :Pied presseur - Pied universel :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Pie universal :Control tensión hilo - AUTO

Retourner le bord et faire un ourlet de 12mm. Placer l’endroit du tissue sous le pied de façon à ce que le point se réalise sur la pliure du tissu. Ceci tout en tirant le tissu pour lui donner la forme d’une coquille. Couper l’excès de tissu au dos, près de la ligne de couture.

Girar hacia abajo el borde del tejido y planchar. Colocar el derecho del tejido arriba, de manera que la parte del zig-zag de la puntada cosa sobre el borde doblado, estirando el tejido y formando un dobladillo de concha. Recorte el exceso de tela del lado trasero, aproxime a la línea de costura.

Suggestion utile: Pour obtenir une apparence plus agréable, essayez d’utiliser des réglages différents pour largeur, la longueur et la tension.

POSE DE BOUTONS

COSIDO DE BOTONES

RÉGLAGES :Pied presseur - Pied universel :Pied fermeture glissière

AJUSTES :Pie prensatelas - Pie universal :Prensatelas de cierres

Positionner le tissu et le bouton sous le pied presseur. Abaisser le pied. Tourner le volant afin de s'assurer que I'aiguille passe nettement dans les trous gauche et droit du bouton (régler la largeur du point en fonction du bouton) et coudre le bouton lentement en utilisant approximativement 10 points.

Coloque el botón en la posición deseada, baje el prensatelas, Gire el volante para comprobar que la aguja entra limpiamente en los agujeros derecho e izquierdo de botón (ajuste el ancho de la puntada) y cosa lentamente el botón con unas 10 puntadas.

Si une tige de maintien est requise, placer une aiguille de reprisage sur la partie supérieur du bouton et coudre.

Suggestion utile: Pour fixer le fil, tirez les deux fils vers l’arrière du tissu et liez-les ensemble.

Page 54 of the Singer Sewing Machine (7258) user manual — FEATHER STITCH
Page 54 · click to enlarge
Page 54

DECORATIVE AND STRETCH STITCHES

SETTINGS :Presser foot - General Purpose Foot or Satin Stitch Foot :Thread tension control - AUTO

Stretch stitches are mainly for use on knit, or stretchable fabrics, but can also be used on woven materials.

STRAIGHT STRETCH STITCH

Straight stretch stitch is far stronger than an ordinary straight stitch because it locks three times - forwards, backwards and forwards.

Singer Sewing Machine (7258) — STRAIGHT STRETCH STITCH diagram (page 54)
Fig. 36

It is particularly suitable for reinforcing the seams of sportswear in stretch and non-stretch fabrics, and for curved seams which take a lot of strain.

Use this stitch also to top-stitch lapels, collars and cuffs to give a professional finish to your garments.

HONEYCOMB STITCH

The Honeycomb stitch is ideal for smocking and useful for overcasting and attaching elastic and stretch lace.

Singer Sewing Machine (7258) — HONEYCOMB STITCH diagram (page 54)
Fig. 37
1. For smocking, first make several rows of gathers across the fabric that you wish to smock.
2. Cut an underlay fabric (such as organdy) and place it under the shirring.
3. Sew the honeycomb stitch over the gathered rows, securing them in place.

OVEREDGE STITCH

This is the same type stitch used by the garment industry in making sportswear - it forms and finishes the seam in one operation.

It’s very effective for use in repairing raw or worn seams of garments.

FEATHER STITCH

The pleasing appearance of this stitch enables it to be used for decorative topstitching or for attaching laces and trims.

It is also ideal for quilting applications and edge-joining.

Page 55 of the Singer Sewing Machine (7258) user manual — POINT PLUME
Page 55 · click to enlarge
Page 55

POINT DÉCORATIFS ET POINTS EXTENSIBLES

PUNTADAS DECORATIVAS Y ELÁSTICAS

RÉGLAGES :Pied presseur - Pied universel ou pour point bourdon :Réglage tension du fil supérieur - AUTO

AJUSTES :Pie prensatelas - Pie universal o para coser en satén :Control tensión hilo - AUTO

Les points extensible sont utilisés surtout sur les tricots et les tissus extensibles, mais peuvent tout aussi bien êtres utilisées sur des tissus tissés.

Las puntadas elásticas se usan principalmente en tejidos o telas elásticas, pero se pueden usar también en materiales de lana.

POINT DROIT EXTENSIBLE

PUNTADA RECTA TRIPLE

Ce point est beaucoup plus solide que le point ordinaire, vu qu’il s’exécute en trois fois, une fois en avant, une fois en arrière et ecore une fois en avant.

La puntada recta triple es mucho más fuerte que la puntada recta corriente, ya que entrelaza tres veces–hacia adelante, hacia atrás y hacia adelante.

Ce point spécial convient particulièrement bien pour les coutures des vêtements sport et les coutures en courbes. Il est aussi utilise pour surpiquer les cols et les poignets.

Es particularmente adecuada para reforzar las costuras de prendas deportivas de tejidos elásticos y no elásticos y para costuras curvas que requieren una gran resistencia.

Utilizar también esta puntada para sobrecoser solapas redondeadas, cuellos y puños, ya que proporciona un acabado profesional a las prendas.

POINT NID D’ABEILLE

PUNTADA PANAL

Le point nid d’abeille est idéal pour la couture de smocks et utile pour surfiler et coudre de la dentelle élastique et extensible.

La puntada panal es ideal para adornar con nido de abeja y es útil para sobrehilado y colocar cintas elásticas.

1. Para esta puntada, primero realice varias líneas de fruncidos a través de la tela que desea adornar con la puntada de panal.
1. Pour la couture de types smock, débuter en cousant plusieurs rands de fronce sur le tissu que vous voulez faire du smock.
2. Corte una tela como cubierta (como un organdí) y colóquelo por abajo.
2. Coupez une pièce de tissus d’entoilage (comme un organdi) et placer le sous la section froncé.
3. Cosa la Puntada Panal sobre las líneas fruncidas, asegurándolas en su lugar.
3. Coudre plusieurs rangs de points nids d’abeilles sur les fronces pour les tenir en place.

POINT SURJET EXTENSIBLE

PUNTADA SOBRE-ORILLADO

Point extensible spécial pour assembler et surfiler en une seule opération. Il est utilisé dans l’industrie de la confection, surtout pour les vêtements de sport, comme les maillots de bain. Il peut cependant aussi s’utiliser sur des tissus non- extensibles.

Este es el mismo tipo de puntada usada por la industria de la confección en la fabricación de prendas. Se forma y acaba la costura en una operación.

Es muy efectivo usarlas para reparar costuras de prendas desgastadas o viejas.

C’est très efficace pour réparer des coutures défaites ou des vêtements endommagés.

POINT PLUME

PUNTADA PLUMA

L’aspect agréable de ce point lui permet de servir de couture visible à plat, ou pour assembler les dentelles, ou pour l’insertion de pièces de type lingerie.

El aspecto agradable de esta puntada permite su uso como adorno o la aplicación de encaje o paneles internos en lencería o fajas.

Il est aussi idéal pour le matelassage et l’assemblage.

También es ideal para aplicaciones de acolchados o unir orillas.

Page 56 of the Singer Sewing Machine (7258) user manual — ENTREDEUX STITCH
Page 56 · click to enlarge
Page 56

RIC-RAC STITCH

Ric-rac is primarily used for a decorative top-stitch. It is ideal for edging neck-bands, armholes, sleeves and hems. When manually adjusted to a very narrow width, it also can be used for sewing high stress seams.

Singer Sewing Machine (7258) — RIC-RAC STITCH diagram (page 56)
Fig. 38

DOUBLE OVERLOCK STITCH

The Double overlock stitch has three main uses. It is perfect for attaching flat elastic, for overcasting, and for seaming and overcasting in one operation. It is primarily used on slightly stretch fabrics and non-stretch fabrics such as linen, tweed, and medium to heavy-weight cotton.

CRISS-CROSS STITCH

Used primarily for decorative machine stitching.

ENTREDEUX STITCH

Useful for decorative stitching on borders and for use in heirloom sewing. The Entredeux stitch is most often sewn with a Wing Needle (SINGER Style 2040) to create holes in the stitch pattern.

Helpful Hint: A slight + adjustment of the tension will increase the size of the hole when using a Wing Needle.

Page 58 of the Singer Sewing Machine (7258) user manual — SLANT PIN STITCH
Page 58 · click to enlarge
Page 58

LADDER STITCH

The Ladder stitch is primarily used for drawn thread hemstitching. It can also be used for sewing over thin tape in an opposite or same color. Place the stitch in the center and a special effect will be obtained for decoration.

Another use for the ladder stitch is couching over narrow ribbon, yarn or elastic.

For drawn thread work, choose a coarse linen type fabric and after sewing draw the thread out within the ladder for an open airy appearance.

PIN STITCH

The Pin stitch is a traditional stitch pattern used for picot-like edges and for applique work.

BLANKET STITCH

The Blanket stitch is traditionally a hand sewn stitch used to put bindings on blankets. This multi-purpose stitch can also be used for couching, applique, drawn thread hemstitching and creating fringe.

SLANT PIN STITCH

Excellent for hemstitching projects like table linens. Picot- like stitch can also be made on sheer materials. Sew along the raw edge of fabric and trim close to the outside of the stitching.

Page 60 of the Singer Sewing Machine (7258) user manual — EDGE-JOINING STITCH
Page 60 · click to enlarge
Page 60

SLANT OVEREDGE STITCH

Seams and overcasts in one operation to produce a narrow, supple seam, particularly suited to swimwear, sportswear, T-shirts, babywear in stretch nylon, jersey and cotton jersey.

CROSSED STITCH

Singer Sewing Machine (7258) — CROSSED STITCH diagram (page 60)
Fig. 39

Use to sew and finish elastic fabrics or for decorative work.

CHEVRON STITCH

Use to create decorative borders.

GREEK KEY STITCH

A traditional pattern suited for decorative borders and edge finishings.

EDGE-JOINING STITCH

Singer Sewing Machine (7258) — EDGE-JOINING STITCH diagram (page 60)
Fig. 40

SETTINGS :Presser foot - General Purpose Foot :Thread tension control - AUTO

This is a popular decorative stitch. It can also be used for joining two separate pieces of fabric, leaving a little space in between. To attach two separate pieces of fabric together, leave a little space in between. To prepare the fabric: Fold under the seam allowances on the cut edges, and press. Baste folded edges to tissue paper with about 1/8" (0.3 cm) space between. Stitch over the 1/8" (0.3 cm) allowance, just catching the fabric fold on both sides with needle. Remove bastings and paper; press.

Page 62 of the Singer Sewing Machine (7258) user manual — 7258-P52-84
Page 62 · click to enlarge
Page 62
Singer Sewing Machine (7258) — 7258-P52-84 diagram (page 62)
Fig. 41

It is a versatile stitch used for joining fabric pieces as well as for decorative machine stitching.

Both of these stitches are perfect for attaching flat elastic. They can also be used for smocking and as a seam finish.

Page 64 of the Singer Sewing Machine (7258) user manual — MORE DECORATIVE STITCHES & IDEAS FOR DECORATIVE MACHINE STITCHING
Page 64 · click to enlarge
Page 64

MORE DECORATIVE STITCHES & IDEAS FOR DECORATIVE MACHINE STITCHING

SETTINGS :Presser foot - Satin stitch foot :Thread tension control - AUTO or -1

You should carry out a test sewing on an extra piece of the fabric being sewn to check the decorative pattern to be used.

Before starting to sew, check that there is enough thread wound onto the bobbin to ensure that the thread will not run out during sewing.

For best results, stabilize fabric with a tear-away or wash- away stabilizer underneath when stitching.

Helpful Hint: Bobbin thread should not appear on the top side of the fabric, so it may be necessary to slightly lower the tension setting.

Singer Sewing Machine (7258) — MORE DECORATIVE STITCHES & IDEAS FOR DECORATIVE MACHINE STITCHING diagram (page 64)
Fig. 42
Singer Sewing Machine (7258) — MORE DECORATIVE STITCHES & IDEAS FOR DECORATIVE MACHINE STITCHING diagram (page 64)
Fig. 43
Singer Sewing Machine (7258) — MORE DECORATIVE STITCHES & IDEAS FOR DECORATIVE MACHINE STITCHING diagram (page 64)
Fig. 44
Singer Sewing Machine (7258) — MORE DECORATIVE STITCHES & IDEAS FOR DECORATIVE MACHINE STITCHING diagram (page 64)
Fig. 45
Singer Sewing Machine (7258) — MORE DECORATIVE STITCHES & IDEAS FOR DECORATIVE MACHINE STITCHING diagram (page 64)
Fig. 46
Page 66 of the Singer Sewing Machine (7258) user manual — (C) (C)
Page 66 · click to enlarge
Page 66

BUTTONHOLE MAKING

tab B Languette B Lengüeta B

AUTOMATIC BUTTONHOLE

tab A Languette A Lengüeta A

USING BUTTONHOLE FOOT

Your machine offers you two different widths of bartack, keyhole and round end buttonholes sewn by a system that measures the size of the button and calculates the size of buttonhole required. All of this is done in one easy step.

PROCEDURE

* Use an interfacing in the area of the garment where

buttonholes are placed. Stabilizer or regular interfacing can be used.

* Make a practice buttonhole on a scrap of the actual fabric

from your project. Then try the buttonhole with your button.

1. Select one of buttonhole patterns.
2. Replace the presser foot with the buttonhole foot. (Refer to “Changing presser foot” on page 28 - 29.)
3. Insert the button into the buttonhole foot. (Refer to “Using buttonhole foot” above.)

(C)

4. Lower the buttonhole lever (C) so that it drops down vertically between the stoppers (A) and (B).

(A) (B)

Buttonhole foot Pied boutonnière Prensatelas de ojales

(C) (C)

(C)

Page 68 of the Singer Sewing Machine (7258) user manual — 7258-P52-84
Page 68 · click to enlarge
Page 68
Singer Sewing Machine (7258) — 7258-P52-84 diagram (page 68)
Fig. 47
5. Carefully mark the position of buttonhole on your garment.
6. Place the fabric under the foot. Pull out the bobbin thread underneath the fabric to a length of about 4 inches to the rear.
7. Align the buttonhole mark on the fabric with the mark on the buttonhole foot, and then lower the buttonhole foot.
8. While holding the top thread, start the machine.

* Sewing will be completed automatically in the following order.

Buttonhole foot alignment position Position d’alignement du pied boutonnière Posición de alineación del pie de ojaladora

9. When sewing is finished, use a buttonhole opener/seam ripper to open up the fabric in the center of the buttonhole. Be careful not to cut any of the stitching.
Page 70 of the Singer Sewing Machine (7258) user manual — PROCEDURE
Page 70 · click to enlarge
Page 70

CORDED BUTTONHOLES Hook filler cord (such as crochet thread or buttonhole twist) over the spur and pull both ends of the cord forward under the foot and tie off the cord as shown in the illustration.

Sew buttonhole so that zigzag stitches cover the cord.

When completed, release the cord from foot and snip off extra length.

MANUAL BUTTONHOLE

* Use the automatic buttonhole foot up to 1 3/4 “(45 mm) in length, but don’t lower the buttonhole lever or a beep will sound.

* Use the satin foot to create larger buttonholes.

* Carefully mark the buttonhole length on your garment. Place the fabric with the buttonhole marked under the buttonhole foot. Slide the foot forward so that the needle pierces the fabric at the beginning of the buttonhole.

PROCEDURE

1. Start the machine to form first bartack and left side of buttonhole.
2. Sew second bartack and stitch backward until needle reaches beginning of buttonhole.
3. Stitch forward to the end of buttonhole mark to complete buttonhole.
4. Push the reverse stitch switch to tie off the stitches.

Spur Saliente Tige

Page 72 of the Singer Sewing Machine (7258) user manual — (3) (4)
Page 72 · click to enlarge
Page 72

3. CARING FOR YOUR MACHINE

CLEANING HOOK AREA AND FEED DOGS

Always disconnect the machine from power supply by removing the plug from the wall-outlet.

CAUTION

To ensure the best possible operation of your machine, it is necessary to keep the essential parts clean at all times.

1. Raise the needle to its highest position.

(1)

2. Remove the needle plate (1).
3. Remove the bobbin case (2).

(2)

4. Clean the feed dogs and hook area with the lint brush. Put one drop of sewing machine oil on the hook race as indicated by the arrows. (A, B)

(A)

(B)

5. Replace the bobbin case with the projection (3) positioned against the spring (4). Replace the needle plate.

(3) (4)

Page 73 of the Singer Sewing Machine (7258) user manual — ATTENTION
Page 73 · click to enlarge
Page 73

3. ENTRETIEN DE VOTRE MACHINE

3. CUIDE SU MAQUINA

NETTOYAGE DES GRIFFES ET DU CROCHET

LIMPIAR EL AREA DEL TRANSPORTADOR Y LA LANZADERA

Siempre desconecte la máquina de la fuente de alimentación retirando el enchufe del tomacorriente de la pared.

Débranchez toujours la machine de l’alimentation électrique en retirant la fiche de la prise murale.

ATTENTION

PRECAUCION

Pour assurer les meilleures conditions de “travail” à votre machine, il est nécessaire de garder les pièces essentielles toujours propres. Toujours débrancher la machine de la prise.

Es necesario que mantenga las piezas esenciales limpias siempre, para obtener un funcionamiento eficáz de su máquina.

1. Relever l’aiguille à sa position la plus haute.
1. Levantar la aguja a la posición más alta.
2. Retirez la plaque aiguille (1).
2. Quite la placa aguja (1).
3. Retirez le boîtier à canette (2).
3. Quite la caja bobina (2).
4. Nettoyer les griffes et le crochet avec le pinceau.
4. Limpiar el área del transportador y de la lanzadera con la brocha.

Mettre une goutte d’huile pour machine à coudre sur le doigt au centre de la coursière, comme indiqué par les flèches (A, B).

Echar una gota de aceite para máquina de coser por el eje central de lanzadera y el carril de lanzadera como está indicado con las fiechas. (A, B)

5. Replacez le boîtier à canette avec la butée (3) positionnée contre le ressort (4). Replacez la plaque aiguille.
5. Vuelva a colocar la caja bobina (3) contra el muelle (4). Coloque de nuevo la placa aguja.
Page 74 of the Singer Sewing Machine (7258) user manual — THREADING THE TWIN NEEDLE
Page 74 · click to enlarge
Page 74

4. OTHER INFORMATION

Singer Sewing Machine (7258) — 4. OTHER INFORMATION diagram (page 74)
Fig. 48

SATIN STITCH FOOT

The Satin stitch foot is grooved to permit dense stitching to pass under it easily. It is most useful for sewing satin stitches and as an alternative to the General Purpose Foot when sewing Stretch Stitches.

Closely spaced zig-zag stitches are called satin stitches. This is an attractive stitch used primarily for appliqueing and bar tacking. Slightly loosen top thread tension for satin stitching. Use a backing of tissue paper or interfacing for to avoid puckering.

TWIN NEEDLE (Optional)

A twin-needle produces two rows of parallel stitches for pin tucks, double top stitching and decorative sewing.

Use of a SINGER Brand 3mm (Style 2025) Twin Needle is strongly recommended.

THREADING THE TWIN NEEDLE

1. Insert the second spool pin. Place a spool on each spool pin. Thread the two threads as one. Draw one thread through each needle from front to back.
2. Pick up bobbin thread as for single needle sewing. Pull the three threads together under the presser foot to the back of the machine, leaving about 6” (15 cm) of thread.
Page 75 of the Singer Sewing Machine (7258) user manual — ENFILAGE DE L’AIGUILLE DOUBLE
Page 75 · click to enlarge
Page 75

4. RENSEIGNEMENTS AUTRES 4. INFORMACIÓN ADICIONAL

PIED POUR POINT BOURDON

PIE PRENSATELAS PARA COSER EN SATÉN El pie prensatelas para tejido satén está rebajado para permitir que las puntadas densas pasen fácilmente bajo el prensatelas. Es muy útil para coser puntadas en satén y es una alternativa al pie prensatelas universal cuando se cosen puntadas elásticas.

Le pied pour point bourdon est doté de rainures afin que les points serrés puissent passer facilement par dessous. Il convient bien pour la couture de points bourdon et comme remplacement pour le pied universel lors de la couture de points extensible.

Les points zigzag serrés sont appelés points bourdon. Ils conviennent bien au faufilage et aux coutures par application. Pour le point bourdon, diminuer légèrement la tension du fil supérieur. Utilisez un tissus d’entoilage pour éviter de faire froncer le tissus.

La puntada de zig-zag corta, se llama puntada satén. Esta es una puntada atractiva usada para aplicaciones, atacados y presillas. Aflojar suavemente la tensión del hilo superior para esta puntada. Use una cubierta de papel suave para evitar fruncidos.

AIGUILLE JUMELÉE (FACULTATIF)

APLICACION DE DOS AGUJA DOBLE (Opcional)

El uso de la aguja doble, produce la costura de dos puntadas de forma paralela, puntadas superiores dobles y puntadas decorativos. Cuando utilice “agujas dobles”, el ancho de la costura no deberá nunca ajustarse por encima de la separación de la “aguja doble”, sin importar la puntada seleccionada. De no hacerlo así se romperán las agujas y podría resultar dañada la máquina.

Une aiguille double procure deux rangées de points parallèles pour les nervures, pour surpiqûre et des effets décoratifs. L’utilisation d’une aiguille double de 3 mm de la marque SINGER (style 2025) est fortement recommandée.

Se recomienda usar una aguja doble (estilo 2025) de 3 mm marca SINGER.

ENFILAGE DE L’AIGUILLE DOUBLE

ENHEBRADO DE DOS AGUJAS

1. Colocar el carrete adicional. Enhebrar los dos hilos a través del mismo sistema, pero se ensartará cada hilo en una aguja de adelante hacia atrás.
1. Insérer un deuxième porte-bobine. Placer une bobine de fil sur chaque porte-bobine. Procéder a l’enfilage comme si vous n’aviez qu’un fil jusqu’au guide fil de l’aiguille. Passer un fil dans chaque aiguille de l’avant vers l’arrière.
2. Extraer el hilo de la bobina, como la costura con una sola aguja. Jalar los tres hilos juntos bajo el prensatelas de adelante hacia atrás, dejando alrededor de 6” (15 cm).
2. Tenir les deux fils dans votre main gauche et faire accomplir au volant un tour complet. Tirer les deux fils vers le haut pour faire remonter le fil de la canette. Passer ces trois fils sous le pied presseur et laisser dépasser à l’arrière de celui-ci 6” (15 cm).
Page 76 of the Singer Sewing Machine (7258) user manual — STRAIGHT STITCH NEEDLE POSITION
Page 76 · click to enlarge
Page 76

STRAIGHT STITCH NEEDLE POSITION

The position of the needle when sewing straight stitch may be adjusted to anyone of 13 different positions with the Stitch Width Control as illustrated:

Singer Sewing Machine (7258) — STRAIGHT STITCH NEEDLE POSITION diagram (page 76)
Fig. 49
Page 77 of the Singer Sewing Machine (7258) user manual — 7258-P52-84
Page 77 · click to enlarge
Page 77

RÉGLAGE DE LA POSITION D’AIGUILLE POUR LE POINT DROIT 13 positions d’aiguille sont utilisables pour la couture droite en utilisant le contrôle de largeur de point.

AJUSTE DE POSICION DE AGUJA PARA PUNTADA RECTA 13 posiciones de aguja disponibles para acolchados, puntadas de revestimiento, etc.

Page 78 of the Singer Sewing Machine (7258) user manual — DARNING & EMBROIDERY FOOT
Page 78 · click to enlarge
Page 78

5. SPECIAL ACCESSORIES

STRAIGHT STITCH FOOT

Use this foot when close control is needed according to the type of fabric or stitching procedure.

OVERCASTING FOOT

Edge guide Guide de bordure Guía de orillas

This foot is used to guide fabric when overcasting. Place your fabric under the foot with its edge against the edge guide and start to sew.

DARNING & EMBROIDERY FOOT

Extension arm Bras de rallonge Brazo extensor

This special foot may be used to create free motion embroidery, free motion monograms, as well as free motion quilting, also known as stippling.

Machine Preparation • For free motion embroidery and monograms: Set machine for Zigzag Stitch in the width you desire. The stitch length will be controlled by the movement of your hands.

  • For free motion quilting (stippling): Set machine to Straight Stitch. The stitch length will be controlled by the movement of your hands.
  • Cover feed dogs with darning plate.
  • Attach Darning & Embroidery Foot, making sure the extension arm sits over the needle clamp screw.

Sewing Instructions 1. Stencil or draw your pattern onto the right side of your fabric.

2. Insert fabric under presser foot.
3. Lower presser foot and begin moving your fabric following your design lines.
Page 79 of the Singer Sewing Machine (7258) user manual — PIED DE REPRISE ET DE BRODERIE
Page 79 · click to enlarge
Page 79

5. ACCESSOIRES SPÉCIALES 5. ACCESORIOS ESPECIALES

PIED À POINT DROIT

PIE COSTURA RECTA

Utilisez ce pied pour obtenir un meilleur contrôle, dépendamment du type de tissus ou de la procédure de couture.

Use este pie cuando requiera un control estricto de acuerdo con el tipo de tela o procedimiento de costura.

PIED À SURJET

PIE PARA SOBREHILAR

Utilisez ce pied pour guider le tissu lorsque vous faite un point surjet. Placer le tissu sous le pied en plaçant le rebord du tissu sur le guide de bordure et débuter la couture.

Este pie se usa para guiar la tela cuando de sobrehila. Coloque se tela abajo del pie con la orilla en contra de la guía y comience a coser.

PIED DE REPRISE ET DE BRODERIE

PIE PARA ZURCIR Y BORDAR

Ce pied est spécialement conçu pour créer de la broderie à main lever, des monogrammes à main lever, aussi bien que du matelassage à main lever, aussi appelés piqures libres.

Este pie prensatelas se puede usar para bordado libre, monogramas de movimiento libre, así como acolchado libre, conocido también como bordado libre con costura recta.

Préparation de la machine • Pour broderie et monogrammes à main libre: Régler la machine au point Zigzag à la largeur désirez. La longueur du point sera contrôlée par le mouvement de vos mains.

Preparación de la máquina • Para el bordado libre y monogramas: Fijar la máquina para puntada Zigzag en el ancho que deseé. El largo de puntada lo controlará el movimiento de sus manos.

  • Pour le matelassage à main levée (piqûre libre): Réglez la machine en point droit. La longueur sera contrôlée par le mouvement des mains.
  • Para un acolchonado (punteado): Ponga la con la puntada recta. El largo de la puntada será controlado por el movimiento de sus manos.
  • Recouvrer les griffes avec la plaque couvre griffe.
  • Cubra los Dientes Impelentes con la Placa CubreImpelentes.
  • Enclenchez le pied de reprise et de broderie, assurez–vous que le bras d’extension est bien au-dessus de la vis du pince-aiguille.
  • Instale el pie para zurcir y bordar – asegurese de que el brazo de la extensión esté sobre el tornillo de la agarradera.

Instructions pour la couture 1. Décalquez ou dessinez votre motif sur l’endroit de votre tissue

Instrucciones para coser 1. Dibuje o traze su diseño al lado derecho de la tela.

2. Coloque la tela debajo del prensatela.
2. Insérez le tissu sous le pied presseur.
3. Baje la palanca del prensatelas y comience a mover la tela siguiendo el diseño.
3. Abaissez le pied presseur et commencez à déplacer votre tissu en suivant les lignes du motif.
Page 80 of the Singer Sewing Machine (7258) user manual — ROLLED HEM FOOT
Page 80 · click to enlarge
Page 80

GATHERING FOOT

Singer Sewing Machine (7258) — GATHERING FOOT diagram (page 80)
Fig. 50

The gathering foot can form single rows of shirring quickly and easily. You can also use this foot to gather one fabric while simultaneously attaching it to another fabric which remains flat.

To do shirring of a single layer of fabric: 1. Attach gathering foot and select straight stitch.

2. Place the fabric to be gathered underneath the gathering foot.
3. Select a long stitch length,which produced more fullness, and increase upper thread tension slightly.

To gather one fabric and stitch onto another fabric: 1. Attach gathering foot and select straight stitch.

2. Place the fabric to be gathered underneath the gathering foot.
3. Insert the other fabric (that will remain flat) into the slot of the foot.
4. Lower the needle and sew a few stitches while holding the thread ends taut.
5. As you sew, hold the upper fabric with your left hand and the lower fabric with your right hand. Though they will feed together through the machine, they will feed at different rates.

ROLLED HEM FOOT

1. Select a soft, light to medium weight fabric.
2. For approximately 1 inch of the beginning of the fabric, press a 1/8” hem, then turn fabric againand press. There should now be a total of 1/4” of fabric turned.
3. Attach Rolled Hem Foot.
4. Select a Straight Stitch, medium length.
5. Stitch approximately 1/2” of the beginning of the folded hem.
6. Leave the needle in fabric and lift presser foot.
7. Guide fabric into scroll of foot.
8. Lower foot and continue to sew, holding the thread tails firmaly.

For an alternative look, try a zig-zag stitch.Test sew on a

scrap fabric first, to determine desired length and width settings for the stitch.

Page 82 of the Singer Sewing Machine (7258) user manual — 6. PERFORMANCE CHECKLIST
Page 82 · click to enlarge
Page 82

6. PERFORMANCE CHECKLIST

GENERAL PROBLEMS Machine does not sew. * Power switch is turned off.- Turn on the switch. * Buttonhole lever is not raised when sewing stitch patterns. – Raise buttonhole lever. * Buttonhole lever is not lowered when sewing buttonhole. – Lower buttonhole lever. * Bobbin winder is engaged. – Disengage bobbin winder (see page 16 - 17). Machine jams/knocks. * Thread is caught in hook.- Clean hook (see page 70 - 71). * Needle is damaged.- Replace needle (see page 26 - 27). Fabric does not move. * Presser foot is not lowered - Lower presser foot. * Stitch length is too short - Lengthen stitch length.

STITCHING PROBLEMS Machine skips stitches. * Needle is not all the way up into needle clamp (see page 26 - 27). * Needle is bent or blunt. - Replace needle (see page 26 - 27). * Machine is not threaded correctly (see page 20 - 21). * Thread is caught in hook. - Clean hook (see page 70 - 71). Stitches are irregular. * Needle size is not correct for thread and fabric (see page 26 - 27). * Machine is not threaded correctly (see page 20 - 21). * Top thread tension is too loose (see page 28 - 29). * Fabric is being pulled or pushed against machine feeding action. - Guide it gently. * Bobbin has not been wound evenly. - Rewind bobbin. Needle breaks. * Fabric is being pulled or pushed against machine feeding action. - Guide it gently. * Needle size is not correct for thread and fabric (see page 26 - 27). * Needle is not all the way up into the needle clamp (see page 26 - 27). * Twin needle is being used but stitch width is set too wide (see page 72 - 73). * Too much thread appears on the underside of stitching. * Upper thread not correctly thread (see page 20 - 21).

THREAD PROBLEMS Thread bunches. * Top and bobbin threads are not drawn back under presser foot before starting seam. - Draw both threads back under presser foot about 6 inches (10 cm) and hold until a few stitches are formed. Needle thread breaks. * Machine is not threaded correctly (see page 20 - 21). * Top thread tension is too tight (see page 28 - 29). * Needle is bent. - Replace needle (see page 26 - 27). * Needle size is not correct for thread and fabric (see page 26 - 27). Bobbin thread breaks. * Bobbin case is not threaded correctly (see page 18 - 19). * Lint accumulates in bobbin case or hook. - Remove lint (see page 70 - 71). Fabric puckers. * Top thread tension is too tight. - Adjust thread tension (see page 28 - 29). * Stitch length is too long for sheer or soft fabric. - Shorten stitch length.

Page 83 of the Singer Sewing Machine (7258) user manual — PROBLÈMES DE FIL
Page 83 · click to enlarge
Page 83

6. VÉRIFICATION DES PETITS PROBLÈMES DE COUTURE

6. CUADRO DE VERIFICACION DE RENDIMIENTO

PROBLÈMES GENERAUX

PROBLEMAS GENERALES Máquina no cose. * El interruptor de energía no está conectado. - en la posición LOW o HIGH. * La palanca de ojal no está levantada cuando se cosen patrones de puntadas. - Palanca de ojal levantada. * La palanca de ojal no está abajo cuando se cosen ojales. - Palanca de ojal baja. Máquina se atasca/rechina. * El hilo está enredado en la lanzadera. - Limpiar la lanzadera (vea página 70 - 71). * La aguja se rompe. - Reponer la aguja (vea página 26 - 27). La tela no se mueve. * El prensatelas no está bajado perfectamente. - Bajar el prensatelas. * Longitud del punto es demasiado corto. - Prolongar la longitud del punto.

La machine ne coud pas: * L’interrupteur est hors fonction. L’activé * Le levier pour boutonnière n’est pas relevé lorsque vous cousez des motifs de points. - Relevez le levier pour boutonnière. * Le levier pour boutonnière n’est pas abaissé lorsque vous cousez une boutonnière. - Abaissez le levier pour boutonnière. * Bobineur est engagé- Désengager le bobineur (voir page 16 - 17) La machine est coincer: * Le fil est cassé dans le crochet - le netoyer (voir page 70 - 71). * L’aiguille est endommagée - remplacer l’aiguille (voir page 26 - 27). Le tissu n’avance pas: * Le pied presseur n’est pas abaissé - l’abaisser. * La longueur du point est trop courte - l’augmenter.

PROBLEMAS DE PUNTO La máquina salta puntos. * La aguja no está fijada en la barra aguja (vea página 26 - 27). * La aguja está torcida o obtusa. - Reponer la aguja (vea página 26 - 27). * La máquina no enhebra correctamente (vea página 20 - 21). * El hilo está enredado en la lanzadera. - Limpiar la lanzadera (vea página 70 - 71). Puntos son irregulares. * El número de la aguja no es correcto para el hilo ni el material (vea página 26 - 27). * La máquina no esta enhebrada correctamente (vea página 20 - 21). * La tensión del hilo superior es demasiado floja (vea página 28 - 29). * El material está tirado o empujado contra la acción de alimentación. - Guiarlo suavemente. * La bobina no se ha devanado de un modo igual. - Volver a devanar la bobina. La aguja se rompe. * El material está tirado o empujado contra el acción de alimentación. * El número de la aguja no es correcto para el hilo ni el material (vea página 26 - 27). * La aguja no está fijada en la barra aguja (vea página 26 - 27). * Exceso de hilo aparece por debajo de la costura. * Hilo superior no enhebrado correctamente (ver página 20 - 21).

PROBLÈMES DE COUTURE

La machine saute des points: * L’aiguille n’est pas bien insérée (voir page 26 - 27). * L’aiguille est courbée ou épointée - la changer (voir page 26 - 27). * La machine n’est pas correctement enfilée (voir page 20 - 21). * Le fil est cassé dans le crochet - le nettoyer (voir page 70 - 71). Les points sont irréguliers: * La grosseur de l’aiguille n’est pas correcte pour le fil et le tissu (voir page 26 - 27). * La machine n’est pas enfilée correctement (voir page 20 - 21). * La tension supérieure est trop lâche (voir page 28 - 29). * Le tissu est tiré ou poussé dans le sens inverse des griffes-le guider correctement. * La canette n’a pas été enroulée régulièrement - la refaire. L’aiguille casse: * Le tissu est tiré ou poussé dans le sens inverse des griffes - le guider correctement. * La grosseur de l’aiguille n’est pas correcte pour le fil et le tissu (voir page 26 - 27). * L’aiguille n’est pas bien insérée (voir page 26 - 27). * Trop de fil apparait en dessous du tissu. * Le fil du haut n’est pas enfiler correctement (voir page 20 - 21).

PROBLÈMES DE FIL

Les fils s’emmêlent: * Les fils supérieur et inférieur ne sont pas tirés sous le pied presseur et vers l’arrière, avant de commencer les coutures - les maintenir pendant quelques points. Le fil de l’aiguille casse: * La machine n’est pas correctement enfilée (voir page 20 - 21). * La tension du fil supérieur est trop serrée (voir page 28 - 29). * L’aiguille est tordue - remplacer l’aiguille (voir page 26 - 27). * La grosseur de l’aiguille n’est pas correcte pour le fil et le tissue (voir page 26 - 27). Le fil de la canette casse: * La boîte à canette n’est pas enfilée correctement (voir page 18 - 19) * La bourre du tissu s’est accumulée dans la boîte à canette ou la coursière - l’enlever (voir page 70 - 71). Le tissu fronce: * La tension du fil supérieur et inférieur est trop serrée - l’ajuster (voir page 28 - 29). * La longueur du point est trop longue pour les tissus légers et fins - la réduire.

PROBLEMAS DE HILO Los hilos se juntan. * Los hilos superior e inferior no están extraidos debajo del prensatelas antes de empezar a coser, - Sacar ambos hilos debajo del prensatelas unos 10 cm y mantener hasta que se formen unos pocos puntos. La aguja se rompe. * La máquina no esta enhebrada correctamente (vea página 20 - 21). * La tensión del hilo superior es demasiado apretada (vea página 28 - 29). * La aguja está torcida. - Cambiar la aguja (vea página 26 - 27). * El número de la aguja no es correcto para el hilo ni el material (vea página 26 - 27). El hilo inferior se rompe. * La caja bobina no enhebra correctamente (vea página 18 - 19). * Los hilos se acumulan en la caja bobina o en la lanzadera. - Quitarlos (vea página 70 - 71). La tela no queda plana. * Las tensiones del hilo superior e inferior están demasiado apretadas. - Ajustar las tensiones del hilo (vea página 28 - 29). * La longitud del punto es demasiado largo para material fino o suave - Acortar la longitud del punto.

Page 84 of the Singer Sewing Machine (7258) user manual — ENGLISH / FRANÇAIS / ESPAÑOL
Page 84 · click to enlarge
Page 84

ENGLISH / FRANÇAIS / ESPAÑOL

© Part No. 82242 1/09

Ask about the Singer Sewing Machine (7258)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Singer Sewing Machine (7258)

Be the first to ask — other owners or our team will answer.

Original document

Singer Sewing Machine (7258) manual PDF

84 pages·17.8 MB·Household Appliance·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…