Instruction/ maintenance manual of the product L1 3Com
Go to page of 20
User guide Bef ore using the mach ine, read this user guide thoroughly and make sure that you hav e understood it..
2 CONTENTS CONTENTS ............... ................ ................ ................ .......... 2 GENERAL ................. ................ ................ ................ .......... 3 DESCRIPTION OF FIELD OF APPLICATION ................. ... 3 SYMBOLS .
3 GENERAL This user guide describes in detail how to use, ma intain and inspe ct the chain sharpening machine. It also describe s the steps to be taken to ensure maximum safety , how the safety components are designed and how they work and how to check and inspect them .
4 SYMBOLS Before using the chain sharpening mach ine, read this user guide thoroughly and make sure that you have understood it all. W ear eye protecti on.
5 SAFETY REGULA TIONS Locate the machine where it is not exposed to rain or moisture. The site must be well lit. The machine must not be located close to gas, liquids or ot her materials that might catch fire or explode. Only a service technician is permitted to carry out work on the machine.
6 POWER SUPPL Y In order to obtain the best resu lt th e machine should be connected to a car battery 12 volt (max 12-14 volt, min 9 ampere). NOTE: Battery placemen t. Make sur e that the battery terminals ar e connected to the corr ect poles of the battery .
7 Machine operating controls 1. Start the motor of the sharpening machine. 12. Chain ru lers. 2. Start the automatic system. 13. Ad justing the grinding angle 0°- 35°. 4. Electric power (12-14 V DC) in. 14. Grinding wheel. 5. St op button. (z ero-voltage cu tout.
8 INST ALLING THE SHARPENING MACHINE Install the machine on a bench or stand. NOTE: The machine must be se cu r ely fixed. 1 The machine shou ld be mounted so that the front edge of it r e aches 1-5 mm over the edge of the bench or stand.
9 CENTRING THE GRINDING WHEEL If the lengths of the right and left cutting links turn out dif ferent on sharpening, this can be adjusted with a djusting screw 11. When the screw is adjusted, the length of th e inner or outer cutting links increases. TRIAL SHARPENING T est the various functions of the machine and study its motions.
10 SHARPENING CUTTING LINKS W ith manual or automatic shoutdow n. The mach ine can be st opped manually without a stop clamp when sharpening is co mplete, or with a stop clamp as described below . Activate Power on, switch 7 Start grinding motor only with switch 1.
11 FOR A DOUBLE LINK, PROCEED AS FOLLOWS Sharpen the other (2) (Fig E) of the two links on the same side, double links 2.3. Stop the autom ati c system with switch 2. Fix the clamp 1 (Fig F) betw een the two double links 2.3. Start the aut oma tic system with switch 2 and the motor with switch 1.
12 SHARPENING SETTING Setting the stroke between the cutting links. (Slacken the wingnut and push it to the right for a shorter stroke.) Adjust the cutting tooth length setting. (Clockwise = shorter cutting tooth) Depth adjustment of the grinding wheel.
13 GRINDING THE DEP TH GAUGE LUGS Set the grinding angle (o ° degrees); see unde r Grinding angle. Install the correct grinding wheel 1 (F ig G) for grinding the d epth gauge lugs (6 mm). Profile the grinding wh eel so that it m atches the lugs 2. Adjust 3 back so that the grinding whee l 1 is aimed at the lug 2.
14 MAINTENANCE CHANGING THE GRINDING WHEEL 1. Lift up the grinding head (1) and remove the guard (9). 2. Hold the grinding wheel ( 2) and sl acken the nut (3) manu ally or with pliers. 3. Remove the old grinding wheel an d fit the new one. Hand-tighten the nut The incoming power must always be switched off.
15 SETTINGS AND SER V ICIN G If one cutting link gets too deep or too shallow , this can be changed by slackening screw 1, 2, 3 or 4 and turning motor 5 as shown. T urn the motor in the relevant direction and tighten the screws. The machine is lar gely maintenance- free, but it should be kept clean by removing any grinding dust.
16 TROUBLESHOOTING The chain is not fixed during sharpening (Fig. I). T ighten M6 nut (1) clockwise about one turn, or more if necessary . The incoming power must always be switched off. More thor ough servicing or tr oubleshooting must be done by the dealer’s servicing team.
17 25 23 22 21 20 18 17 16 15 15 13 12 1 2 3 4 14 5 6 11 10 9 8 7 19 24.
18 1 2 3 4 5 11 12 13 10 9 7 8 8.
19 EC DECLARA TION OF CONFORMITY Manufacturer: Markusson Development Systems AB T egelbruksvägen 762 31 Rimbo, Sweden hereby declares that: Sliprobot L1 Logosol Sliprobot L1 has been manufactured in .
Basic tips: Cutting angle, see page 8 in the operator's manual . In most case s we recommend to grind at 60 degrees or fr om 50 to max 75 degrees. This also applies if the chain man ufac t urers recommend other settings. Sharpening settings, see page 12 in the operator's manual.
An important point after buying a device 3Com L1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought 3Com L1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data 3Com L1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, 3Com L1 you will learn all the available features of the product, as well as information on its operation. The information that you get 3Com L1 will certainly help you make a decision on the purchase.
If you already are a holder of 3Com L1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime 3Com L1.
However, one of the most important roles played by the user manual is to help in solving problems with 3Com L1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device 3Com L1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
