
Vacuum sealing Food easily spoils under the influence of oxygen, light and temperatures above 0°C. Storing food in a fridge increases shelf life a little.
The advantages of Vacuum sealing:
∙∙The removal of oxygen gives bacteria and mould little opportunity to grow ∙∙Moisture and nutrients are retained. ∙∙Protects from odours and odour accumulation ∙∙Hygienic storage.
The food therefore stays fresh significantly longer!
Generally This appliance is for private and indoor use only and must not be used commercially. Please read the instruction manual carefully and keep it at a safe place. When the appliance is given to ano- ther person the instruction manual should be passed to that per- son, too. Only use the appliance as described in the instruction manual and pay attention to the safety information. No liability for damages or accidents will be accepted, which are caused by not paying attention to the instruction manual.
∙∙The appliance must be plugged in only in accordance with the data shown on the rating label. ∙∙For safety reasons, the rating plate must not be removed. ∙∙Use the appliance only if the cord shows no damages. Check this before every use! ∙∙Do not touch the power plug with wet hands. ∙∙Plug off the appliance after each use or in case of failure. ∙∙Do not pull at the cord. Don’t pull it over edges and don’t bend it too much. ∙∙Keep the cord away from hot parts. ∙∙
The appliance can be used by children aged 8 and above and persons with limited physical, sensory or mental capa- bilities or lack of experience/knowledge, provided that are su-

pervised or have been provided with instruction in the safe use of the appliance and have understood the resulting dangers. Children must not use the packaging as a plaything. Cleaning and user maintenance must not be carried out by children un- less they are 8 years or older and are supervised. ∙∙Children under the age of 8 must be kept away from the appli- ance and the connecting cable. ∙∙The appliance must not be operated using a timer or a separate remote system! ∙∙When using a powercord extension it is important that children are not pulling at it or a trip hazard occurs. A cable drum must always be unwound. ∙∙Don’t keep the appliance outside or in a humid environment. ∙∙
Never immerse the appliance in water.
∙∙Use the appliance never after a malfunction, e.g. when it fell down or was damaged in any other way. ∙∙The producer takes no responsibility for wrong use, which co- mes from not obeying the instruction manual ∙∙To avoid any dangers, any repairs at the appliance, e.g. an ex- changement of the cord, must only be done by customer ser- vice. Only use original spare parts. ∙∙
Do not vacuum any products which may contain alcohol, petrol or any other explosive substances. Do not vacuum living animals ∙∙The device is not intended for continuous use, always allow to cool between sealing operations.
Workspace: Important: Never put the device on or next to a hot surface (e.g. the rings of a stove). Always put the device on a surface that is level, stable, temperature-resistant and dry. Keep it away from the edge of work surfaces so that it cannot fall off during use.

Before initial use:
∙∙Wipe off the device with a damp towel. ∙∙The sealing rings and the bag sealing bar must be clean and level, otherwise it will not be possible to generate a vacuum.
∙∙Unplug the device and leave to cool down.
Do not immerse the device in water or pour water over it. ∙∙For hygienic reasons, the device must be cleaned after every use. ∙∙Remove the upper rubber lid and clean in warm soapy water, leave to dry and insert it again. ∙∙Wipe the other parts with a damp cloth with detergent and dry. Do not use abrasive detergents.
Ensure that the welding strip and the upper seal are not damaged. ∙∙Ensure that no liquids enter the vacuum extractor when clea- ning.
Roll of film / bags Use only the special rolls of film / plastic bags with 3D-structure that are suitable for vacuuming and sealing. If the wrong film is used it will stick to the device and dama- ge the sealing bar. The following special films are available from Steba, among other things:
Please visit our homepage to get an overview about our current assortment of vacu- um film rolls and bags.
∙∙ · ∙∙


A) Vacuum nozzle (should not be covered by films) B) Gasket C) Sealing bar D) Vacuum chamber E) Release button F) Rubber lid 1) Vacuuming & sealing – stop 2) Sealing
∙∙Determine the space required for the food ∙∙For the lower and the head welding, add 8cm length. ∙∙Place the front end of this tube of film against the black oval sealing lip, ensuring that it is smooth and free of creases. ∙∙Close the lid and press gently in the middle of the lid. ∙∙Seal with the „Seal“ button. The unit stops automatically when the welding has been done. ∙∙Press the release button and remove the film bag.
∙∙

∙∙Vacuum sealers are designed to vacuum food or other products in vacuum foil. If the device is used in any other way, it might get damaged and the warranty void. ∙∙Do not seal spoiled food or flammable liquids. ∙∙Only use foils suitable for vacuuming. ∙∙Place the food in the bag. Ensure that the bag is not damaged by any sharp objects, such as bones. ∙∙Damp and in the area of the welding seam soiled bags are difficult to weld. ∙∙Do not seal twice in the same place, since this may cause the film to burn. Instead, place a second weld.
∙∙Place the food in the bag. Ensure that the bag is not damaged by any sharp objects, such as bones. ∙∙
Insert the bag up to half down the vacuuming tray, ensuring that it is free of creases, dry and free of residue. ∙∙Damp bags are difficult to weld. Press excess air out of the bag so the pump does not pump unnecessarily. ∙∙Gently press on the lid and press the “Vas/Seal button. ∙∙Ensure that the vacuum pump does not suck up any liquids. If this occurs, press the stop button immediately. ∙∙The aspiration and the welding stop automatically. ∙∙
Do not seal twice in the same place, since this may cause the film to burn. ∙∙Allow the device to cool for one minute between sealing operations. ∙∙If the device becomes overloaded, the overheating protection will switch the device off. If this happens, disconnect the device from the power supply and leave it to cool for about 20 minutes.

Device does not work
∙∙Do you have power? ∙∙Has the lid been pressed gently? ∙∙Is the film placed in the oval vacuum chamber? ∙∙Is the aspiration covered by a film?
Air in the films ∙∙The weld is not closed ∙∙Did you use an inappropriate film? (use only films suitable for vacuuming) ∙∙Is the film soiled or wet in the area of the weld? ∙∙Is a crease at the weld? ∙∙Is the sealing bar clean?
Disposal: Packaging disposal: Do not throw away the package materials. Please put it in the recycling bin.
Gift box: Paper, should be put to the old paper collection point.
Plastic packaging material and foils should be collected in the special collection containers.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Service and Repair: If the appliance must be repaired, plaese get in touch with your trader or with the manufacturer:
STEBA Elektrogeräte GmbH & Co KG Pointstr. 2, 96129 Strullendorf / Germany Distribution-Tel.: 09543 / 449-17 / -18, Service-Tel.: 09543 / 449-44, Fax: 09543 / 449-19
Problem Solution
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Device does not work | ∙∙ Do you have power? ∙∙ Has the lid been pressed gently? ∙∙ Is the film placed in the oval vacuum chamber? ∙∙ Is the aspiration covered by a film? | p.6 | |
| Air in the films | ∙∙ The weld is not closed ∙∙ Did you use an inappropriate film? (use only films suitable for vacuuming) ∙∙ Is the film soiled or wet in the area of the weld? ∙∙ Is a crease at the weld? ∙∙ Is the sealing bar clean? | p.6 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.