EN
Polk logo
Official user manual

Polk RT Models

16 pages·3.3 MB·Loudspeaker·PDF·ENDEITNLJA
Polk RT Models
Table of Contents 9 sections LS Models · 265ls 65 f / x ® - ls 65ls 255cls · RT Models · 265rt 625rt 65 f / x ® - rt 65rt 255crt · … ShowHide
Page 1 of the Polk RT Models user manual — LS Models
Page 1 · click to enlarge
Page 1

LS Models

265ls 65 f / x ® - ls 65ls 255cls

RT Models

265rt 625rt 65 f / x ® - rt 65rt 255crt

Page 2 of the Polk RT Models user manual — LS Models
Page 2 · click to enlarge
Page 2

ENGLISH IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 10. WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.

Take Inventory Inside each speaker container, you should find the following: 1. One in-wall loudspeaker or one set of loudspeakers for F/X® models only. 2. Speaker cutout mounting template 3. One Sheer-Grille (for each speaker) 3. Port plug (265-ls, 65f/x-ls, 65-ls, 265-rt, 65f/x-rt & 65-rt only) 4. One Owner’s Manual 5. Registration Card Important Note: If anything is missing or damaged, or if your speaker fails to operate, notify Polk Audio Customer Support Services immediately at 800-377-7655.

  • Loudspeaker Installation You will need:
  • Pencil for marking the location of installation.
  • Keyhole saw, utility knife or materialappropriate tool for cutting drywall or other wall material.
  • Level.
  • Screwdriver, preferably powered, with Phillips Head bit.
  • Power drill with appropriate bit (optional, for starting wall cut).

Trace around the template.

Installation Recommendation For Optimum Performance Important Note: Vanishing Series Loudspeakers are not magnetically shielded and should not be placed closer than 1’ (30cm) from a CRT (tube) television or video monitor.

Cut the hole with the appropriate tool.

Product Disposal—Certain interna tional, national and/or local laws and/ or regulations may apply regarding the disposal of this product. For further detailed information, please contact the retailer where you purchased this product or the Polk Audio Importer/ Distributor in your country. A listing of Polk Audio Importer/Distributors can be found on the Polk Audio website www.polkaudio.com or by contacting Polk Audio at 5601 Metro Drive, Baltimore, Maryland 21215, USA—Phone: +1 410 358-3600.

When installing your loudspeakers, be aware of the weight of your particular model and the sturdi ness of the material into which you are installing the speaker. Be aware of any concealed studs, electrical wiring or plumbing in the wall or ceiling into which you are installing the speakers.

Wall Or Ceiling Surface Preparation If you’re installing your Vanishing Series speaker into a heavily textured wall or ceiling (e.g. stucco or popcorn finish), you must prepare the wall surface immediately around the speaker cutout. Sanding and smoothing the wall or ceiling surface will ensure the speaker and grille both seat properly and flat to the surface.

If you doubt that you possess the necessary skills or tools, consult your Polk Audio dealer or a professional installer.

Wire Recommendations (minimum recommended) Runs Gauge Lengths up to 25' 18 or 16 Lengths greater than 25' 16 or 14 but less than 50' Lengths greater than 50' 14 or 12 but less than 75' Lengths greater than 75' 12

Keep these guidelines in mind and always use your own good judgment when controlling volume: • You should limit prolonged exposure to volumes that exceed 85 decibels(dB).

For more about safe volume levels, go to the Occupational Health and Safety Administration (OSHA) guidelines at http://www.osha.gov/dts/ osta/otm/noise/standards_more.html

2 Polk Audio Customer Service1-800-377-7655 (Outside US & Canada: 410-358-3600) Monday-Friday, 9:00 AM-6:00 PM EST, polkcs@ polkaudio.com
Page 3 of the Polk RT Models user manual — Imaging
Page 3 · click to enlarge
Page 3

Surround SPEAKER PLACEMENT Polk Audio F/X® surround loudspeakers give you nearly endless placement options. But remember that where you place your surround speakers requires some careful thought, as installation requires that you cut a hole in your wall or ceiling.

Imaging

Imaging (65f/x-ls model only) F/X Surround Loudspeakers offer switchable “Diffuse” and “Solid” imaging patterns to create the surround effect you desire.

Paint Recommendation We highly recommend you use a can of spray paint matched to the wall color you want the Sheer-Grilles to blend with.

A “Diffuse” image is defined as one which creates a “cloud” of sound; think of the effect as ambient sounds which fill the environment all around you, but are less localizable.

A “Solid” image is one which creates a more pin- point sound; sound is more localized. The location of sounds in the sound field is more identifiable.

To paint the Sheer-Grille 1. Elevate the Sheer-Grille off of a flat surface. This will ensure even coverage of the grille frame and make it easier to pick up. Mounting Idea: Two spray can caps will raise the grille high enough. 2. Hold the spray paint about 12" from the grille and at a 45° angle.

Tweeter Switch (LS and RT models except F/X models) Filter—If your listening room is very reflective, with smooth sheetrock walls, hardwood floors, and non-cushioned furniture, the sound will be overly “bright” and unnatural. Selecting the “Filter” setting compensates for the effect of reflectiv ity in a hard room. Tweeter attenuation flattens room response, without hindering higher frequency response, for warmer, more realistic sound and more accurate imaging. Norm—If your room is not reflective, with curtains, artwork, lots of cushioned furniture and carpeting, sound will be absorbed by the room, resulting in more realistic reproduction and more accurate imag ing. In this case, select the tweeter “Norm” setting.

Diagram shows speaker locations for 5.1 and 7.1 systems, when two additional in-wall speakers are installed in the rear wall.

Left/Right Orientation: F/X® surround loud- speakers have a left/right orientation, and each speaker is clearly marked on the serial number label on the back of the magnet for installation on either the right or left. Right and left are defined from your listening area as you face your system’s center channel.

3. Apply one light, thin coat, moving evenly side to side over the grille, then work your way around the perimeter of the grille to ensure you cover the grille frame. 4. After each application of paint, wait approximately 1 minute, rotate the grille 90°, and apply the next thin coat. Important Note: You must rotate the grille 90°. Use your hands to define the next 90° rotation and always rotate the grille in the same direction of travel.

Center Channel Speaker Placement Install the 255c-ls or 255c-rt as close as possible to ear level. If the speaker needs to be installed higher, aim the tweeter down as required. Do not block the center channel with your TV or furniture.

Wall Dist.

>2' (60cm) (60cm)

Wall Distance Switch (65f/x-rt and all LS Models except the Center Channel) In-wall loudspeakers excel when placed more than 2’ (60cm) from side walls. If position limitations demand that in-wall loudspeakers be installed closer than 2’ (60cm) from side walls or ceiling, the proximity of the surface can result in a response “bump” between 50 and 200Hz. This can cause in-wall speakers to sound “boomy.” The “Wall Distance” switch flattens response and eliminates “boominess” without sacrificing deep bass response, for more lifelike sound.

Please Note: For more on speaker placement go to: www.polkaudio.com/education/article.php?id=15 or www.polkaudio.com/downloads/hthandbook.pdf

5. Three light, even applications should cover the grille and frame adequately. Remember to work your way around the grille frame to cover it evenly and completely.

For more information visit our website at www.polkaudio.com 3

Show 5 more labels / short text on this page
Room Environment Controls · Diffuse / Solid · tV · Tweeter · Filter / Norm
Page 4 of the Polk RT Models user manual — Specifiations For complete Vanishing Series specifications, visit www.polkaudio.com
Page 4 · click to enlarge
Page 4

When to Use the Provided Port PluG Important Note: Use the provided port plug when you are installing any of the in-wall loudspeakers listed below in an area larger than a standard open stud bay. Ensure the plug seats all the way into the port.

Polk RT Models — Specifiations For complete Vanishing Series specifications, visit www.polkaudio.com diagram (page 4)
Fig. 1 · Specifiations For complete Vanishing Series specific…

The port plug should be used on the following models: 265-ls, 65f/x-ls, 65-ls, 265-rt, 65f/x-rt & 65-rt.

Dimensions Model265-ls265-rt65f/x-ls65f/x-rt A. Overall Dimensions20 7/8" H x 8 7/8" W (530.2mm x 225.4mm)20 7/8" H x 8 7/8" W (530.2mm x 225.4mm)14 3/8" H x 8 7/8" W (365.1mm x 225.4mm)14 3/8" H x 8 7/8" W (365.1mm x 225.4mm) B. Cutout Dimensions19 3/16" H x 7 1/4" W (487.4mm x 184.2mm)19 3/16" H x 7 1/4" W (487.4mm x 184.2mm)12 3/4" H x 7 1/4" W (323.9mm x 184.2mm)12 3/4" H x 7 1/4" W (323.9mm x 184.2mm) C. Product Depth3 3/4" (95.3mm)3 3/4" (95.3mm)3 1/2" (88.9mm)3 1/2" (88.9mm) D. Mounting Depth (using 1/2" drywall)3 1/4" (82.6mm)3 1/4" (82.6mm)3" (76.2mm)3" (76.2mm)
Polk RT Models — Specifiations For complete Vanishing Series specifications, visit www.polkaudio.com diagram (page 4)
Fig. 2 · Specifiations For complete Vanishing Series specific…
Dimensions Model625-rt65-ls65-rt A. Overall Dimensions14 3/8" H x 8 7/8" W (365.1mm x 225.4mm)14 3/8" H x 8 7/8" W (365.1mm x 225.4mm)14 3/8" H x 8 7/8" W (365.1mm x 225.4mm) B. Cutout Dimensions12 3/4" H x 7 1/4" W (323.9mm x 184.2mm)12 3/4" H x 7 1/4" W (323.9mm x 184.2mm)12 3/4" H x 7 1/4" W (323.9mm x 184.2mm) C. Product Depth3 3/8" (85.7mm)3 1/2" (88.9mm)3 1/2" (88.9mm) D. Mounting Depth (using 1/2" drywall)2 7/8" (73mm)3" (76.2mm)3" (76.2mm)
Dimensions (Center Channel) Model255c-ls255c-rt A. Overall Dimensions9 5/16" H x 14 13/16" W (236.5mm x 376.2mm)9 5/16" H x 14 13/16" W (236.5mm x 376.2mm) B. Cutout Dimensions7 5/8" H x 13 1/8" W (193.7mm x 333.4mm)7 5/8" H x 13 1/8" W (193.7mm x 333.4mm) C. Product Depth3 3/4" (95.3mm)3 3/4" (95.3mm) D. Mounting Depth (using 1/2" drywall)3 1/4" (82.6mm)3 1/4" (82.6mm)
Polk RT Models — Specifiations For complete Vanishing Series specifications, visit www.polkaudio.com diagram (page 4)
Fig. 3 · Specifiations For complete Vanishing Series specific…

Specifiations For complete Vanishing Series specifications, visit www.polkaudio.com

4 Polk Audio Customer Service1-800-377-7655 (Outside US & Canada: 410-358-3600) Monday-Friday, 9:00 AM-6:00 PM EST, polkcs@ polkaudio.com
Page 5 of the Polk RT Models user manual — A B C D
Page 5 · click to enlarge
Page 5

A B C D

B A

A B

B A

D

For more information visit our website at www.polkaudio.com 5

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Polk RT Models

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Polk RT Models

Be the first to ask — other owners or our team will answer.

Original document

Polk RT Models manual PDF

16 pages·3.3 MB·Loudspeaker·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…