EN
Plugwise logo
Official user manual

Plugwise Adam

28 pages·2.3 MB·Thermostat·PDF·ENDEFRITJA
Plugwise Adam
Table of Contents 17 sections boiler gateway Adam · Installation manual · Nederlands Inhoudsopgave · English Table of content · … ShowHide
Page 1 of the Plugwise Adam user manual — boiler gateway Adam
Page 1 · click to enlarge
Page 1

boiler gateway Adam

Installation manual

Model 159-01 Nederlands | English

6000-0080-03

Page 2 of the Plugwise Adam user manual — English Table of content
Page 2 · click to enlarge
Page 2

Nederlands Inhoudsopgave

EU-conformiteitsverklaring 3 Pakketinhoud 4 Meer informatie 4 Vooraf 4 Voorzorg en veiligheid 5 Compatibiliteit 5 Installatie 6 Het gedrag van de LED 11 Goed om te weten 12 Alternatieven om te verbinden met internet12 Problemen met wifi 12 Problemen met de lokale web-interface 13 Problemen met de app 13 Problemen met het verwarmen 13

English Table of content

EU-conformity declaration 15 In the package 16 More information 16 Before you start 16 Precautions and safety 17 Compatibility 17 Installation 18 The LED behaviour 23 Good to know 24 Alternative ways to connect to the internet 24 Issues using wifi 24 Issues with the local web interface 25 Issues with the app 25 Issues with heating 26

Page 3 of the Plugwise Adam user manual — EU-conformity declaration
Page 3 · click to enlarge
Page 3

Installation manual

This document contains the installation procedure and functional description of this product.

More information about Adam can be found on our website: plugwise.com

© 2018, Plugwise. All rights reserved.

EU-conformity declaration

Plugwise B.V. hereby declares that this product is in compliance with the applicable essential requirements of the appropriate EC-Directives, including 1999/5/EC (R&TTE). A copy of the EU declaration of Conformity is available at www.plugwise.com/product-conformity

Old electrical and electronic appliances very often contain valuable materials. Therefore, never dispose discarded appliances with normal household waste. Always hand in your old appliances at the municipal collection points for electrical and electronic equipment.

Page 4 of the Plugwise Adam user manual — More information
Page 4 · click to enlarge
Page 4

In the package Before you start

Make your existing thermostat smart with Adam. You install Adam between the current central thermostat and the central heating boiler. Connect Adam with the internet and set the room temperature or a temperature schedule via the app.

Do you have an Adam HA? Then there is a Zigbee stick installed in Adam. With the Zigbee stick you can extend Adam with Plugwise Zigbee HA products, such as smart heating controls for zone heating.

USB adapter Adapter cable

ID The ID is the 8 letter code on the sticker on the back of Adam.

More information

Wifi network name The wifi network name starts with smile and is on the sticker on the back of Adam.

More information about Adam can be found on our website plugwise.com/adam or plugwise.com/adam-ha

Plugwise Adam — More information diagram (page 4)
Fig. 1 · More information

Adam Wall plate · Symbols

Page 5 of the Plugwise Adam user manual — Precautions and safety
Page 5 · click to enlarge
Page 5

Precautions and safety

installation at hand, so you can first set up an internet connection (temporarily) via LAN.

  • Check the availability and quality of

Make sure you have at hand: » ID of Adam » Wifi network name of Adam » Wifi network password

the wifi connection beforehand, also check if there is a free power outlet available near the boiler.

Compatibility Adam works with» an OpenTherm boiler » an on/off boiler » an OpenTherm thermostat

We advice you to have Adam installed by the installer of your central heating system.

Disconnect the boiler from the

electricity before you continue.

Adam communicates with the heating system via the OpenTherm protocol. This means that the thermostat and boiler must both support OpenTherm. You can find this in the manual of the boiler and thermostat. It can also be recognized by the OpenTherm logo.

The existing boiler wires that connect

the boiler to the thermostat have to be connected to the OpenTherm or on/off connection of the boiler. You can find this information in the manual of your boiler.

The boiler wires that connect the

boiler to the thermostat should not be longer than 50 metres and must not have a greater resistance than 5 Ohm per wire. If this is not the case however, we advise you to have the wires replaced.

On/off Adam also supports on/off boilers. It is required to use a thermostat that sends a room temperature to Adam. Therefore you need an OpenTherm thermostat or a zone thermostat Lisa. In addition, the maximum boiler temperature that is set on the boiler must be indicated in the local web interface of Adam.

Are you in doubt about the quality of the wifi connection at the central heating boiler? It is convenient to have an extra long LAN cable for the

On/off thermostats are not supported.

Installing Adam yourself? · OpenTherm

Page 6 of the Plugwise Adam user manual — 1. Configure zone heating
Page 6 · click to enlarge
Page 6

Installation

1. Configure zone heating

  • Connect the adapter cable to the USB

to configure a zone.

adapter and Adam. Plug the adapter into the wall socket. Wait until Adam has booted up: the upper light and light in the middle are blinking slowly (Adam is in acces point mode).

  • Use the option to create a new zone

(the + sign in the right bottom corner).

For a good reception, make sure the

Plugwise Zigbee HA products, such as the smart heating devices for zone heating, are nearby Adam HA when you add them to the Zigbee network.

  • Use a device (smartphone, tablet or pc) with which you can connect to a wifi network.
  • Search for the Adam wifi network at
  • Use the option to add a new device to

the network settings of your device. The name of the network starts with smile and can be found on the sticker on the back of Adam.

the zone. Follow the instructions in the web interface. » Make sure the Plugwise Zigbee HA product is powered on. » Use the push button of the product to set the product into joining mode so it becomes visible for Adam HA.

  • Connect with this wifi network. The ID

is the network password (see sticker).

Plugwise Adam — 1. Configure zone heating diagram (page 6)
Fig. 2 · 1. Configure zone heating

Look at the instructions in the manual of the Plugwise Zigbee HA product for detailed information about how to set the product in join mode.

  • Open the web browser on your

Look at the extra software installation configuration instruction online (plugwise.com/adam-ha) for a detailed overview of the steps you have to follow to install Plugwise zone heating.

device and go to setup.now or to 192.168.40.40. The local web interface of Adam opens.

  • Use the menu to go to Set up in order
Page 7 of the Plugwise Adam user manual — Installation
Page 7 · click to enlarge
Page 7
Plugwise Adam — Installation diagram (page 7)
Fig. 3 · Installation

Installation with Opentherm thermostat

  • Unplug the boiler and Adam from the

electrical power.

  • Disconnect the thermostat wire

between the boiler and the thermostat at the boiler boiler end of the wire and connect the installation cable with Adam at the boiler icon .

Installation with zone thermostat Lisa

  • Connect the wire running to the

thermostat with the installation cable at Adam with the thermostat icon .

This is not necessary if you install Adam

without an OpenTherm thermostat but with

zone thermostat Lisa.

  • Determine the position of Adam near

the boiler and mount the wall plate of Adam to the wall.

Installation with thermostat Anna (OpenTherm)

  • Click Adam onto the wall plate.
  • Connect both the boiler and Adam to

the power outlet and wait until Adam has started up: the upper light and light in the middle are blinking slowly (Adam is in acces point mode).

  • Open the local web interface of Adam

Consult the manual of the boiler for more information about the connector of the boiler.

in the web browser of your device (setup.now or 192.168.40.40). Make sure you are still connected to the

20,5° · 20,5° · 20,5°

Page 8 of the Plugwise Adam user manual — 2. Connect to the boiler
Page 8 · click to enlarge
Page 8

2. Connect to the boiler

Adam wifi network (see also page 18)!

  • Go via the menu to Settings > Heating

system > Heating. Here you can turn on the Plugwise regulation. You have to turn on the Plugwise regulation if you have installed zone heating. Save your settings.

  • Go via the menu to Settings > Heating

system > Boiler. Check if the protocol of the boiler is recognized (on/off or OpenTherm), see image. Not the right boiler protocol or is there no boiler protocol detected? Check whether you have connected Adam correct to the boiler.

Plugwise Adam — 2. Connect to the boiler diagram (page 8)
Fig. 4 · 2. Connect to the boiler

If correctly installed, restart the boiler and Adam in case of an OpenTherm boiler. Connected to an on/off boiler? Click Update boiler protocol.

  • Go via the menu to Settings > Heating

system > Heating. Enter the details about your heating system below the heading Installation. The Plugwise regulation will use these to heat up your house as optimal as possible. Save your settings.

Plugwise Adam — 2. Connect to the boiler diagram (page 8)
Fig. 5 · 2. Connect to the boiler
Plugwise Adam — 2. Connect to the boiler diagram (page 8)
Fig. 6 · 2. Connect to the boiler
Page 9 of the Plugwise Adam user manual — 2. Connect to the boiler
Page 9 · click to enlarge
Page 9

2. Connect to the boiler

Adam is connected to an on/off boiler

Adam is connect to a heat pump (Elga) Adam cannot detect Elga automatically. Support for the Elga can be activated on the Adam to make the system work. Please send an email to support@plugwise.com, so we can activate this feature. Once support is turned on, the Elga specific setting become visible in the web interface of Adam.

  • Fill in the maximum boiler

temperature that is set on your boiler at Settings > Heating system > Heating.

Does your boiler use a weather- dependent regulation? Activate this in the web interface of Adam and fill in the maximum boiler temperature as is set on your boiler for both low and high outside temperature.

Also check the detected boiler protocol at Adam, see page 20. This should be OpenTherm. In addition it is important that Elga uses her weather dependent regulation. Elga must then be connected as described in scheme K5 or K6 in the Elga installer manual.

Plugwise Adam — 2. Connect to the boiler diagram (page 9)
Fig. 7 · 2. Connect to the boiler

Dip switches on Elga: » Turn the dip switches B1 & B2 on » Turn the dip switch A6 on. » Set the dip switches A1 & A3 to the house » Set the dip switch A8 depending on the communication with the boiler.

Page 10 of the Plugwise Adam user manual — 3. Connect to the internet
Page 10 · click to enlarge
Page 10

3. Connect to the internet

Looking for alternative ways to connect Adam to the internet? Look at “Alternative ways to connect to the internet” at page 24.

  • At Wifi network select the network you want Adam to connect with. Enter the password of the wifi network and save the settings.

Wifi via your browser

Adam is now connecting to the internet. The upper light is blinking irregular and the middle light is on. Your device is no longer connected to the Adam wifi network.

  • Open the local web interface of

Adam. Make sure you are still connected to the Adam wifi network and that you are nearby Adam for a good reception (see also page 18)!

  • Make sure that you reconnect your device to the wifi network to which you just connected Adam.
  • Go via the menu to Settings > Network and open the network settings. Press Scan networks . Adam will search for the available networks to connect with.
  • Go to connect.<a href="http://plugwise.net" rel="nofollow noopener" target="_blank">plugwise.net</a>. Enter the

ID of Adam.

Plugwise Adam — 3. Connect to the internet diagram (page 10)
Fig. 8 · 3. Connect to the internet
  • Login with: Username: smile Password: ID (see sticker)
Plugwise Adam — 3. Connect to the internet diagram (page 10)
Fig. 9 · 3. Connect to the internet
Page 11 of the Plugwise Adam user manual — LED Colour Pattern Description
Page 11 · click to enlarge
Page 11

4. Use Adam

Use Adam via the local web interface (HTML interface) or with the app.

settings, insight in your heating behaviour using graphs, set up zones and or edit the gateway setings.

Make sure that in the following

  • Go to connect.<a href="http://plugwise.net" rel="nofollow noopener" target="_blank">plugwise.net</a>.
  • Login with your ID. Enter username

situations your device is connected to the same network as to which Adam is connected: » When adding Adam to the app. » When using Adam via the web interface.

smile and use the ID as password. The web interface of Adam will open.

App With the app you can easily set the temperature, also when you are not at home.

Local web interface In the local web interface you will find all the functionalities and settings that are available for Adam, e.g. temperature

The LED behaviour

LED Colour Pattern Description

Blinks slowly Blinks slowly Adam is in access point mode

On Blinks slowly In acces point mode and connected to a device

Green Irregular Communication with the wifi network

Green On Adam is on

Green Irregular Communication with the LAN network

Green Green · Green Green

Page 12 of the Plugwise Adam user manual — Good to know
Page 12 · click to enlarge
Page 12

Good to know

Alternative ways to connect to the internet The recommended way to connect with internet you can find on page 22. Prefer an alternative way to connect? Choose one of the following options to connect Adam with the internet. » Option a: Internet via network cable » Option b: Wifi via Android app » Option c: Wifi via WPS

connect to your wifi network. In case after 2 minutes Adam has not made a connection yet to your wifi network, Adam will switch back to access point mode.

Issues using wifi I cannot find the Adam wifi network, what to do? Ensure that Adam is not already connected to the internet via a LAN cable. Wait until Adam has booted up completely before connecting to it. If the and lights are flashing slowly after you connect Adam to the plug socket, this means Adam is in access point mode. Only then it is possible to find the Adam network among the wifi networks. Is Adam not in access point mode? Then reset the network connection.

Option aInternet via network cable
  • Connect a network cable between

the router and Adam.

Option bWifi via Android app

Do you want to connect Adam to wifi and do you have an Android device? Search for the Plugwise Connect app at the Google Play Store. The app will guide you through the process of connecting Adam to the wifi network.

How do I reset the network connection?

  • Press the black button on Adam.

Release the button when the light has blinked 5 times (the light is blinking once each second) and the light starts to blink rapidly. The network settings will be deleted. • Wait until Adam has booted up. The

Option cWifi via WPS

Wifi via WPS is only supported via a

  • special WPS button on your wifi router.
  • Press the black button on Adam for 2 seconds and release.
  • Wait until the upper light is blinking quickly and regularly.
  • Enable WPS on the wifi router to

lights and are blinking slowly. Then try to connect Adam to your wifi network again as described at page 22.

Page 13 of the Plugwise Adam user manual — Good to know
Page 13 · click to enlarge
Page 13

Issues with the local web interface Why is it not possible to open the local web interface? Make sure your device, on which you want to open the web interface, is connected to the same network as Adam is connected to.

I cannot get Adam connected to the wifi network, what to do?

  • First connect Adam to your router

with a LAN cable. • Power up Adam and wait until Adam

  • has booted up: the light is on and the light is blinking. Adam is now connected to the network.
  • Open the local web interface: » go to connect.<a href="http://plugwise.net" rel="nofollow noopener" target="_blank">plugwise.net</a> » log in with the ID of Adam. » enter smile as user name and use the ID as password.
  • Go via the menu to Settings > System >

What I see in the local web interface does not match the current settings, what to do? Remove the cache from the browser and open the page again and/ or try to open the web interface via an incognito window in the browser.

Network. • Press Scan networks. Select the wifi

network you want to connect Adam with and enter the password. Save your settings. • Remove the LAN cable as soon as is

Issues with the app The app is not always working or is very slow, what to do? You need a good internet connection if you want to use the app. Did you connect Adam to a wifi network? Check the quality of the network connection at Settings > System > Network. » -30 dBm: excellent » -67 dBm: very good » -70 dBm: moderate (min. signal strength) » -80 dBm: not good (unreliable) » -90 dBm: not usable

indicated in the web interface.

Is Adam still working if there is no internet? Adam continues to work for you, even if the internet connection has been lost. You can’t use the app now to set the temperature. You can reach the web interface though, but only via the IP address of Adam within your own network. Do you want to set another temperature? You can do this using the thermostat.

Page 14 of the Plugwise Adam user manual — Good to know
Page 14 · click to enlarge
Page 14

Issues with heating The temperature settings of my thermostat are missing Adam retrieves the measured temperature from your room thermostat and sends the desired temperature to the thermostat using the so called “override” functionality of the OpenTherm protocol. It is up to the thermostat to “do something” with this temperature setting. Based on the measured temperature and set temperature the regulation determines whether the boiler should start heating up the house.

The boiler protocol is not detected correctly

  • Check if Adam is connected to the

correct connections of the boiler. • Remove power from the boiler and

Adam. • Power up the boiler and wait until the

boiler has booted up. • Power up Adam an wait until it has

started up, the light is on. • Check now if the correct boiler

protocol is detected: go via the menu to Settings > Heating system > Boiler. Not the correct boiler protocol? Click update boiler protocol.

Thermostats that use OpenTherm do not always do this in the same way. It is possible that your thermostat does not support above mentioned functionalities or that you first have to switch it on. Some commonly used thermostats that have been extensively tested and at that are supported are: » Plugwise Anna (24V) » Honeywell Round Modulation » Honeywell Chronotherm Touch » Remeha iSense (after contact with support)

I have installed zone heating but my house is no longer warming up For zone heating to work properly, the Plugwise regulation should be switched on. You can check this in the local web interface of Adam: Settings > Heating system > Heating. When you switch on the Plugwise regulation, the regulation of the thermostat is being ignored.

Make sure that the heating source to which you have connected Adam is the only heating source in your heating system and that Adam has full access to control this heating source.

You can also install zone thermostat Lisa instead of your existing central room thermostat.

Is your thermostat not in this overview or is it not working as mentioned, please do not hestitate to contact Plugwise.

Page 15 of the Plugwise Adam user manual — Good to know
Page 15 · click to enlarge
Page 15

I have installed zone heating but my house is warming up too much The Plugwise regulation analyses heating for the different zones in the house. When the installation is new, it is possible Adam will heat up your home a little to much because it still have to get familair with your house.

Besides, it is important if you install zone heating that you install Tom’s and or Floors on all radiators, floor heaters and or convectors in the room and that they are all added to the correct zone.

For support go to plugwise.com/support

Page 16 of the Plugwise Adam user manual — ID:
Page 16 · click to enlarge
Page 16

ID:

Plugwise B.V. Wattstraat 56 2171 TR Sassenheim The Netherlands www.plugwise.com

Supportplugwise.com/support
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Plugwise Adam

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Plugwise Adam

Be the first to ask — other owners or our team will answer.

Original document

Plugwise Adam manual PDF

28 pages·2.3 MB·Thermostat·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…