
Copyright 2017, Plugwise. All rights reserved.
This is the short installation manual for the Plugwise Stretch 3. The Stretch is the gateway that works together with the Plugwise Circle or Stealth using the Plugwise ZigBee protocol. The Stretch is the manager in the Plugwise network. With the Circle or Stealth you can measure the electricity consumption and switch appliances on or off in your home.
This document contains information about the installation procedure of this product. For more information about the functionalities of this product, we refer to online information and documentation.
In this manual we shortly describe how to install the Stretch. Because you will always use the Stretch in combination with a Circle or Stealth, we also briefly explain how to set up a good network using the Stretch and Circles. The Stealth has the same functionalities as the Circle, but unlike the Circle that you plug into a socket, the Stealth is a built-in module*.
Plugwise B.V. hereby declares that this product is in compliance with the applicable essential requirements of the appropriate EC-Directives, including 1999/5/EC (R&TTE). A copy of the EU declaration of Conformity is available at www.plugwise.com/product-conformity
Explanation symbols:
Old electrical and electronic appliances very often contain valuable materials. Therefore, never dispose of discarded appliances with normal household waste. Always hand in your old appliances at the municipal collection points for electrical and electronic equipment.
We advise you to have the Stealth installed by
an installer.
*

More information
More information about the Stretch can be found on our website: www.plugwise.com/stretch-3
We advise you to always be careful when installing the Plugwise Stretch 3.
Do not use the product when it is damaged or if it is malfunctioning.
This short installation manual
Avoid contact with water or other liquids.
Never open the casing of the product. The product does not contain components that you can repair yourself.
Gateway to control your
Check the availability and the quality of the WiFi network beforehand near the location where you want to install the Stretch. Make sure you have the password of the WiFi network to which you will connect the Stretch.
Do you want to connect the Stretch to the network using a LAN cable? Make sure you install the Stretch nearby your router.
Keep the short ID of the Stretch at hand. The short ID is the 8 letter code on the sticker on the back of the Stretch.


Installation the Stretch with as many Circles as possible.
The installation can be described in 3 steps: 1. Place the Stick in the Stretch. 2. Place the Stretch. 3. Connect the Stretch to the network. 4. Validate the network connection.
The Circle+ (the Circle that contains a grey back) should always be placed within a 5-meter range of the Stretch. The Circle+ behaves like a ‘router’ in the network. The Circle+ is always reachable for other Circles.
All Circles should be positioned at a maximum distance of 5 to 10 meters of at least one other Circle or the Stretch.
Concrete walls and ceilings will reduce the range of the network.
For a highly responsive network, install as many Circles as possible.
WiFi via WPS is only supported via a special WPS button on the router.
Place the Stretch centrally located in the house, for example near the stairwell at the first floor.
Press the black button on the Stretch for 2 seconds. Wait until the upper (WLAN) light is blinking quickly and
Make sure that there is direct contact of
Circle+ Circle+ · Circle · WiFi via WPS?

regularly.
smartphone or tablet and navigate to a random web address. Because you are connected to the network of the Stretch, you will be redirected to the web page of the Stretch.
Enable WPS on the WiFi router to connect to WiFi. Wait until the Stretch has booted up: the upper light (WLAN) and the light in the middle (STATUS) of the Stretch are on when connected to the network.
Go to the settings via the button in the bottom right of the web page . Go to the WiFi/LAN settings.
If after 2 minutes the Stretch has not made a connection yet to your WiFi network, the Stretch will return back to the access point mode: the upper (WLAN) light and the light in the middle (STATUS) are blinking slowly.
Press ‘Scan’ and select your own WiFi network.
Enter the password of you own WiFi network and save the settings. Wait until the Stretch has booted up: the upper light (WLAN) and the light in the middle (STATUS) of the Stretch are on when connected to the network.
Do you want to connect the Stretch to WiFi and you have an Android smartphone or tablet? Search for the Plugwise Connect app in the Google Playstore. The app will guide you connecting the Stretch to the WiFi network.
Connect a network cable between the router and the Stretch.
No Android? Follow the steps below to connect the Stretch to the WiFi network.
Restart the Stretch by plugging the adapter out and into the wall socket. Wait until the Stretch has booted up: the light in the middle (STATUS) and the lower light (LAN) are on when connected to the network.
Connect your smartphone or tablet to the WiFi network of the Stretch, starting with ‘stretch_’.
Enter the short ID as your password.
Open the web browser on your
Make sure that your smartphone or
WiFi? · Network cable?

tablet is reconnected to the same network as to which the Stretch is connected to. This is also necessary when you want to add the Stretch to the Plugwise app.
the webpage of the Stretch.
Go to the settings via the button in the bottom right of the web page .
Go to the WiFi/LAN settings.
Go to connect.plugwise.net.
Select your own WiFi network, enter the password of your own WiFi network and save the settings. Disconnect the Stretch from the network cable when instructed.
Use your short ID to log in. You will be redirected to the web page of the Stretch when the Stretch is connected to the network.
Press the black button on the Stretch for 5 seconds until the light in the middle (STATUS) has blinked 5 times and the upper light (WLAN) starts to blink rapidly.
The network settings will be deleted. Wait until the Stretch has booted up, then try to connect the Stretch to your WiFi network again.
First connect the network cable
Connect a network cable between the router and the Stretch.
Restart the Stretch by plugging the adapter out and into the wall socket.
Follow the steps “Validate the network connection? - Open the web page of the Stretch” on the previous page to open

The Stretch has 3 LEDs. In the table below the most important behaviour of the lights of the Stretch is explained.
STATUS Green Blink slowly The Stretch is starting up. Wait until the Stretch is ready. When in access point mode, the LEDs STATUS and WLAN are blinking slowly.
STATUS Green Blink slowly, then on
WLAN Green Blinking Communication with the WiFi network.
WLAN Green Blink slowly Cannot connect to the WiFi network. Has something been changed in the router settings? Follow the steps below “having trouble using WiFi?”.
LAN Green Blinking Communication with the network via the network cable.



Plugwise B.V. Wattstraat 56 2171 TR Sassenheim The Netherlands www.plugwise.com
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.