EN
Pixel logo
Official user manual

Pixel TW-282TX remote control

16 pages·1.6 MB·Miscellaneous·PDF·ENDEFRITNLJA
Pixel TW-282TX remote control
Table of Contents 16 sections 页 1 · 页 2 · 页 3 · 页 4 · … ShowHide
Page 1 of the Pixel TW-282TX remote control user manual — 中国制造
Page 1 · click to enlarge
Page 1

Wireless Timer Remote Control

TW-282

中国制造

PSM40 V11.01

Page 2 of the Pixel TW-282TX remote control user manual — Contents
Page 2 · click to enlarge
Page 2

Contents

TW-282 introduction 05 The name of each part 06 09 Prepare for install and use

Install and replace the battery 09

Fix the receiver(TW-282RX) 1 1

Turned on/off the power 1 2

Open the background light of display 1 4

Receiver connected with the camera 1 5 Shooting control 1 6

Single shooting 1 6 Continuous shooting within one sec 17

Overview 03 · Channel Setting 13

Page 3 of the Pixel TW-282TX remote control user manual — Overview
Page 3 · click to enlarge
Page 3

Overview

Thank you for purchasing high-performance PIXEL products

First of all, thank you for purchasing product of Wireless Timer Remote Control TW-282. The shooting ways included single shooting, continuous shooting within one sec, BULB shooting, user-defined time-delay and timing plan for shooting. Low consumption of LCD display will make you be clear at a glance of the using status and using plan. Before use this product, you must read and fully understand this manual, then learn to use the camera to ensure you are familiar with the operation properly. Through this manual you can easily handle the operation method and the attentive things.

Delay shooting 2 0 Timing plan for shooting 23

This manual is current update of 1st Feb, 2012. Please contact to PIXEL distributor for further information, if interesting of the combining usage with products released after this day.

shooting 1 9

Page 4 of the Pixel TW-282TX remote control user manual — Cautions
Page 4 · click to enlarge
Page 4

Cautions

TW-282 introduction

The batteries should not install anti-polarity; Otherwise the batteries may leak corrosive liquids, heat or explosion. Make sure the camera and receiver (TW-282RX) are powered off before install it. When connected the remote cable with the device, do not pull the wires. As this is an electronic product accessory; some of the environment causes may affect the working. However this is hardly ever to get this situation. This product can't be strong vibration, or may lead to product failure. For a long time non-use, please remove the battery to prevent leakage of corrosive liquids and damage the product. Do not put it in high temperature, such as a closed car under direct sunlight, the control panel and other high-temperature areas. Keep dry, don’t use wet hand contact with the product, it must not be immersed in water or exposed to rain, and this may lead to not work properly. Do not use flammable and explosive gases in violation of this warning may cause an explosion or fire. Because this product include battery, regarding how to use battery, please operate it strictly according to related rules, otherwise it may cause explosion, fire or physical injury.

Using the wireless remote control technology to achieve shutter’s external socket with camera for remote control . FSK 2.4GHz wireless controls system, which more reliability and stability, 15 channels available. Operating distance range up to 80M or above. LCD display is showing channel, power, function mode, it's easy to understand and operate. Ultra-low power standby, transmitter (TW-282TX) uses 2pcs AAA batteries, which standby time over four years; the receiver (TW-282RX) uses 3V CR-2 lithium battery, which more than 400 hours of standby time. Different shutter connect cable can be connect with different brand cameras. It can control multiple cameras simultaneously. The camera can be

single shooting, continuous shooting within one sec, BULB shooting and

user-defined delay and timing plan shooting. Set the parameters for timing shooting.

Page 5 of the Pixel TW-282TX remote control user manual — 页 5
Page 5 · click to enlarge
Page 5
Pixel TW-282TX remote control — 页 5 diagram (page 5)
Fig. 1

Please check all included items after open the packing, if missing, please contact the dealer.

1. Transmitter (TW-282TX) 1pc 3. Shutter connect cable 1pc 4 . Manual(this manual) 1pc

4 Release button 3 Decrement button 2 Left move button 1 Background light button

9 Display Timing plan start/stop button 8 7 Increment button Right move button 6 5 Setting/Enter button

Hot shoe fixed mount Output control signal interface 8

11 Battery hatch 12 Product back sticker 13 Item code

Hot shoe fixed nut Quick release plate holding nut

Page 6 of the Pixel TW-282TX remote control user manual — Display of transmitter
Page 6 · click to enlarge
Page 6

Preparation for installation and use

The name of each part

CB1 CLCLCLCLCLCLCLCLCL-

Before use, you should read the user manual of your camera carefully and well understand the manipulation and functional setting. The function setting of camera may influence this item’s efficiency control of the camera.

DC0 DC1 DC2 E3 N3 L1 S1 UC1

10 9 11 1213 13

Install and replace the battery

The transmitter(TW-282TX)

The low battery voltage icon[ ]will twinkle or the character become dim obvious when the power is not enough, that means the low battery voltage has already influence the normal work of the device, which needs to replace the battery in time. The transmitter uses 2pcs AAA batteries; Please follow the steps to replace the battery if needed.

4 5 6 7 8

Display of transmitter

1 Timing plan function area 2 Time display area

The icon of timing shots 12 The icon of interval time 11 The icon of exposure time 10 The icon of delay time 9 8 Low battery voltage icon 7 Delay shooting icon 6 shooting icon 4 Single shooting icon Function area 3

5 Continuous shooting within one sec icon

1. Slide and open the battery hatch.

The icon of channel 13

Show 4 more labels / short text on this page
Display of transmitter · Shutter connect cable · Input plug · Shutter connect plug
Page 7 of the Pixel TW-282TX remote control user manual — TW-282RX
Page 7 · click to enlarge
Page 7

Preparation for installation and use Preparation for installation and use

2. Follow the signs of positive [ + ] and negative [ - ] in the battery compartment to install the battery correctly .

Fix the receiver (TW-282RX)

Receiver can be fixed on the top of camera, rack of camera accessory or tripod.

You should pay attention to the polarity of battery because of the wrong installation will make the device work abnormally, or even physical injury.

Fix the receiver on the hot shoe of camera.

Lock hot shoe fixed nut tightly when you fix it.

3. Close the battery hatch.

Loosen hot shoe fixed nut when you remove . forcibly pull it, in order to avoid damage to the receiver and camera.

the receiver Do not

The receiver(TW-282RX)

The low battery voltage icon[ ]will twinkle when the power is not enough, that means the low battery voltage has already influenced the normal work of the device, which needs to replace the battery in time. The receiver uses CR-2 lithium battery; Please follow the steps to replace the battery if needed. 1. Slide and open the battery hatch. 2. the signs of positive [+] and negative [-] in the battery compartment to install the battery correctly.

TW-282RX

Fix on the rack of camera accessory. the receiver

Fix on the tripod. the receiver

1. Fix the Receiver on the quick release plate through bottom nut . 2. Attach the quick release plate on the tripod .

You should pay attention to the polarity of battery because of the wrong installation will make the device work abnormally, or even physical injury.

3. Close the battery hatch.

Make sure to fix firmly so that it will not slide. the receiver

Follow

Page 8 of the Pixel TW-282TX remote control user manual — Preparation for installation and use Preparation for installation and use
Page 8 · click to enlarge
Page 8

Preparation for installation and use Preparation for installation and use

Turned on/off the power Channel setting

The transmitter(TW-282TX)

Channel setting for transmitter(TW-282TX)

Press any button once, and turn on the power of transmitter. The transmitter stays in the single shooting mode when you turn on the power; timing plan and channel setting will not be changed. The display shows the single shooting icon and communication channel. The transmitter without any operation (except timing plan or implementing BULB status) will shut down automatically after one minute. The receiver(TW-282RX)

Press left move button[ ]or right move button[ ]will move the functional icon to the channel icon[ ].Press Setting/Enter button to change the channel, you will see the channel number is flashing. Thought pressing increment button[ ]or decrement button[ ] to adjust the channel number. 4. Press Setting/Enter button again to save the present channel.

Channel setting for receiver(TW-282RX)

Turn on the power; the channel is default as the last time setting. Press [+CH] and [CH-] button enter to channel setting, the channel icon [CH] on the screen will be flashing. [+CH] is increase the numbe, [CH-] is reduces the number.

1. Hold the power button for 2sec to turn on the POWER Green LED light will be flash every 2sec and the screen displays communication channel . 2. After turn on the power, the set timing communication channel remain effectively . 3. The receiver does not turn off automatically. In the poweron state, press power button 2s and the receiver will be turned off.

ress [+CH] and [CH-] button at same time, or no-action for 10 second, can save and exit. P

* The channel of transmitter and receiver should be the same for shooting effectively.

[ ] · 2s

Page 9 of the Pixel TW-282TX remote control user manual — Preparation for installation and use Preparation for installation and use
Page 9 · click to enlarge
Page 9

Preparation for installation and use Preparation for installation and use

Open the background light of display

Receiver connected with the camera

The transmitter(TW-282TX)

Make sure your receiver has been installed in place and to ensure that cameras and receivers are shut down. First, insert the input plug of the shutter connect cable into the receiver's output control signal socket in place.

Press and hold the background light button for 2 seconds, the background light will be turned on.

Open the background light and press the button twice each 6 seconds, the background light will keep lit. The background light will not be close by hand; it will turn off after 6 seconds automatically without any operation.

The timer remote control will not be able to control the camera if the shutter connect cable didn’t insert correctly.

Fix the camera on the tripod or other fixed frame. protective cover of external shutter socket and put the shutter plug of shutter connect cable in place, then make sure it has been fixed firmly.

The receiver(TW-282RX)

Press and hold the background light button for 2 seconds, the background light will be turned on.

For most of camera shutter socket, there is a mis-plug interface, please note insert direction so as to avoid damage to shutter socket.

Open the background light of the receiver and press the button twice each 6 seconds, the background light will keep lit. The background light will not be close by hand; it will turn off after 6 seconds automatically without any operation.

Turn on the receiver's power and then the camera's power.

2s · Open the · 2s

Page 10 of the Pixel TW-282TX remote control user manual — Shooting control
Page 10 · click to enlarge
Page 10

Shooting control

Shooting control

Sketch map for selecting function mode:

3. Full-press the release button and transmitter will send signal of shooting. The red indicator will light for a while, the camera start shooting.

Make sure to set the camera function to be [ ]. When the camera function is set to be[ ], it may cause continuous shooting.

shooting function Single shooting function

Continuous shooting within one sec function Delay shooting function

The instruction is under the premise that the receiver and camera have been connected tightly, and turned on the power of camera and receiver. The detail instruction of remote shooting will be showing as follow.

[ ], . When the camera function is set to be [ ], the camera will execute delay shooting.

It will be shooting every sec if camera is set as BULB it may cause the problem of under or over exposure.

Continuous shooting within one sec

1. In the power-on state , set the single shooting icon [ ] by pressing the move button[ ]or right move button[ ].
1. In the power-on state, move the transmitter’s activities icon to continuous shooting within one sec icon[ ] by pressing the left move button[ ]or right move button[ ].

In the sleeping state, press any key to wake up transmitter to enter single shooting mode. 2. Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button.

Continuous shooting within one sec second is patent function which issued by Pixel limited Enterprise, it'll support spacing continuous shooting within one sec and never change the single shooting mode.

Single shooting · left · the firs

Page 11 of the Pixel TW-282TX remote control user manual — BULB
Page 11 · click to enlarge
Page 11

2. Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button. 3. Full-press the release button, red indicators of the transmitter and receiver will be lit, keep fully press the button, the transmitter will send signal of shooting continuously, the indicators will blink red and green light in turn. The camera will start to shot, and the shooting speed will be one photo per sec. 4. Release the release button, the transmitter stop sending signal for shooting and the camera will stop shooting.

1. In the power-on state, move the transmitter's activities icon to shooting icon[ ] by pressing the left move button [ ]or right move button[ ]. 2.Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button. 3.Full-press the release button, transmitter will send signal. The red indicator of transmitter starts flashing and start timing, the indicator of receiver will keep lighting. The transmitter continuous output shooting signal. Camera enters into exposure shooting continuously.

BULB

4. Press the release button again, the transmitter stop sending out the shooting signal and the time also stopped on screen displays .

Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], it may cause continuous shooting.

BULB

[ ], It will be shooting every sec if camera is set as BULB it may cause the problem of under or over exposure.

Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], the camera only shoot once but not BULB shooting. When the camera function is set to be [ ],the camera will be continuous shooting. When the camera function is set to be [ ], the camera will be delay shooting once.

When the camera function is set to be[ ], the camera will execute delay shooting.

shooting

Page 12 of the Pixel TW-282TX remote control user manual — 页 12
Page 12 · click to enlarge
Page 12

5. After set up the new parameters, press the set button, save and exit settings. When enter to the delay shooting set, the transmitter will save the previous setting. By pressing the left button[ ]or right button[ ], convert shooting numbers and delay time settings. Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. Operate the delay shooting

The delay shooting function of TW-282 can user-defined the delay time and shots.

1. In the power-on state, move the transmitter’s activities icon to delay shooting icon[ ] by pressing the move button[ ]or right move button[ ]. Press the set button entering the delay setting for adjusts the shooting numbers. The delay shooting icon[ ],number of shooting [ ]will blink at the same time.

Press the left button[ ]or right button[ ], move the transmitter’s activity icon to the delay shooting icon[ ]. Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button.

2. Press button[ ]settings shot number can be increased, press button [ ], settings shot number can be reduced. It can be set between 1 to 99 sheets . 3. Press button[ ]enter into the delay setting of delay shooting. delay shooting time value[ ]will blink at the same time.

the delay shooting icon[ ] ,

Full-press the release button, transmitter will send all the delay shooting information to receiver, the transmitter starts to delay countdown, and red indicator blink quickly and enter to the delay shooting mode.

4. Press the button[ ], set the delay time increased, press button[ ], set the delay time reduced. It can be set between 1 to 59 seconds. 21

Delay shooting · Delay shooting setting · left

Page 13 of the Pixel TW-282TX remote control user manual — 页 13
Page 13 · click to enlarge
Page 13

Timing plan for shooting

4. When countdown is completed, will follow the setting shots output a signal per second to control shooting .
1. In the power-on state, move the functional activities icon to the delay timing program icon[ ]by pressing the left move button[ ]or right move button[ ].

5、Before delay time planning completed, press either transmitter button or receiver button or other , will terminate this planning.

Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], it will start continuous shooting.

2. Press the set button, enter the delay time for ‘second bit’ setting.

[ ], It will be shooting every sec if camera is set as BULB it may cause the problem of under or over exposure.

3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , as the sketch map.

“ ” “ ”

When the camera function is set to be [ ], the camera will perform one or more delay shooting.

When the camera lens focus function is set to be [ M ],the camera will not execute focusing action if half-press the release button of the transmitter.

Delay time of timing plan--seconds setting Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings.

Delay time of timing

Delay time of timing plan--minutes setting

When the camera lens focus function is set to be [ AF ], even receiving the shooting signal the camera will not shoot at the moment as most of camera don't seize focus.

Show 10 more labels / short text on this page
receiver · Delay time setting · The shot number · Exposu · -re time · of timing · of timing · plan setting · plan setting · plan--hours setting
Page 14 of the Pixel TW-282TX remote control user manual — 页 14
Page 14 · click to enlarge
Page 14
1. Press left move button[ ]or right move button[ ], move the transmitter’s activities icon to the interval timing program icon[ ].
1. Press left move button[ ]or right move button[ ], move the transmitter’s activities icon to the exposure timing program icon[ ]. 2. Press the set button, enter the delay time for ‘second bit’ setting. 3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , as the sketch map.
2. Press the set button, enter the time for second bit setting.

“ ” “ ”

3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , as the sketch map.

“ ” “ ”

Exposure time of timing

time of timing Exposure

Interval time of timing

time of timing Interval

Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings.

Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings.

Show 27 more labels / short text on this page
Exposure time setting · Interval time setting · interval “ ” · Exposu · -re time · The shot number · Delay · time · Interval · time · of timing · of timing · of timing · of timing · plan setting · plan setting · plan setting · plan setting · Exposure · time of timing · Interval plan--minutes setting · time of timing · plan--hours setting · plan--minutes setting · plan--seconds setting · plan--hours setting · plan--second setting
Page 15 of the Pixel TW-282TX remote control user manual — 页 15
Page 15 · click to enlarge
Page 15

Search the timing plan 1. Press left move button[ ]or right move button[ ],move transmitter’s activities icon to timing plan icon which can check the related timing project. 2. When check the related projects, if need adjust the parameters, only press the set button to enter the relevant project settings, press the set button again to exit and save your setting. Move the icons sequence showed as below.

The shot number setting

1. Press left move button[ ]or right move button[ ], move the transmitter’s activities icon to the icon of timing shots [ ].
2. Press the setting button enter to set the number of photo in timing plan ' s, Press [ ] to increase the photo number ; Press [ ] to reduce the photo number. 1-99photo number is available , when the screen display means this is unlimited to take the photo .

Delay time Exposure time Interval time Number of photo

3. By pressing button[ ]or[ ],enter into the setting for “ exposure time ” and “ delay time ” , “ interval time ” as the shown picture.
1. Press the left move button[ ]or right move button[ ], move the activities icon to any icon among the timing plan shooting area.
2. Press the timer plan start/stop button transmitter sends the information to receiver . The green light of receiver will be flash twice every 2 sec; that ' s mean the receiver is
4. Press the set button, save and exit settings.

completely to receive information and start operate correctly. Timing plan will be working in the receiver and send the control signal to the camera.

Show 16 more labels / short text on this page
Delay shoot · Singl e · shoot · -ing function · -ing func tion · [ -- ] · Execute timing plan · Interval · Delay · time · time · of timing · of timing · plan setting · plan setting · [ ];
Page 16 of the Pixel TW-282TX remote control user manual — N=1 N=2 N= 3
Page 16 · click to enlarge
Page 16

Shooting control

TW-282 Specification

3.Transmitter's screen will display the running conditions of timing plan, but it will not send any command to the receiver. This is only showing the receiver running conditions and for reference only.

Type : FSK 2.4 GHz wireless control system Transmission distance: 80 meters or above Channel: 15 channels Standby time: Transmitter : more than 4 years(using two 1.5V AAA batteries) Receiver 400 hours (using CR-2 lithium battery) Dimensions (W × H × D) Transmitter: Receiver: Weight with ba ttery Transmitte: Receiver:

Press the timing plan start/stop button[ ]of the transmitter before the timing plan executing completely, the transmitter and receiver will stop regularly scheduled executing.

: : 149 ×49.5 ×24 63mm×38mm×31mm ( ): 70.5g 39.5 g

When the timing plan is running on the receiver, press any button of receiver to stop the operation.

The following examples illustrate the timing plan running: delay time[ ] = 5 seconds, exposure time[ ] = 1 second, shooting interval[ ]= 6 seconds, shooting number[ ] = 3.

N=1 N=2 N= 3

Now you can start to use unique high-performance

Wireless Timer Remote Control

TW-282. If you have any questions, you can contact the local distributor. Or visit the website http://www.pixelhk.com

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

mm mm mm · Shooting output · Focusing output

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
18 p.11
22 p.13

Ask about the Pixel TW-282TX remote control

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Pixel TW-282TX remote control

Be the first to ask — other owners or our team will answer.

Original document

Pixel TW-282TX remote control manual PDF

16 pages·1.6 MB·Miscellaneous·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…