EN
Pixel logo
Official user manual

Pixel TC-252

14 pages·1.3 MB·Miscellaneous·PDF·ENDEFRITNLJA
Pixel TC-252
Table of Contents 14 sections 页 1 · 页 2 · 页 3 · 页 4 · … ShowHide
Page 1 of the Pixel TC-252 user manual — PSM47 V10.02
Page 1 · click to enlarge
Page 1

有线定时快门线 Timer Remote Control

TC-252

PSM47 V10.02

中文 English

Page 2 of the Pixel TC-252 user manual — Contents
Page 2 · click to enlarge
Page 2

Contents

TC-252 introduction 04 The name of each part 0 5 07 Prepare for install and use

Install and replace the battery 07

Connection with the camera 08

Open the background light of display 09

Continuous shooting within one second 11 [ ]shooting 1 3 Delay shooting 14 Timing plan for shooting 1 7 PIXEL TC-252 Specifications 2 4

This manual is current update of 1st Mar, 2012. Please contact to PIXEL distributor for further information, if interesting of the combining usage with products released after this day.

Overview 02 · Shooting control 10 · Single shooting 10

Page 3 of the Pixel TC-252 user manual — Overview
Page 3 · click to enlarge
Page 3

Overview

Cautions

Thank you for purchasing high-performance PIXEL products

The batteries should not install anti-polarity; Otherwise the batteries may leak corrosive liquids, heat or explosion. Make sure the camera and TC-252 are powered off before install it. When connected the remote cable with the device, do not pull the wires. As this is an electronic product accessory; some of the environment causes may affect the working. However this is hardly ever to get this situation. This product can't be strong vibration, or may lead to product failure. For a long time non-use, please remove the battery to prevent leakage of corrosive liquids and damage the product. Do not put it in high temperature, such as a closed car under direct sunlight, the control panel and other high-temperature areas. Keep dry, don’t use wet hand contact with the product, it must not be immersed in water or exposed to rain, and this may lead to not work properly. Do not use flammable and explosive gases in violation of this warning may cause an explosion or fire. Because this product include battery, regarding how to use battery, please operate it strictly according to related rules, otherwise it may cause explosion, fire or physical injury.

First of all, thank you for purchasing product of PIXEL. TC-252 is a high quality wired timer remote control with the function of single shooting, continuous shooting per second,[ ]shooting, user-defined time-delay and timing plan for shooting. Low consumption of LCD display will make you be clear at a glance of the using status and using plan. Before use this product, you must read and fully understand this manual, then learn to use the camera to ensure you are familiar with the operation properly. Through this manual you can easily handle the operation method and the attentive things.

Page 4 of the Pixel TC-252 user manual — TC-252 introduction
Page 4 · click to enlarge
Page 4

TC-252 introduction

The name of each part

LCD display shows the channel, power, function mode. It’s easy to understand and operate. Low power consumption when standby; standby time more than 3 years using 2pcs AAA batteries.

Here are the names of each part:

Support single shooting, continuous shooting within one second, [ ] shooting and .

11 Shutter indicator 10 Display Timing plan start/stop button 9 8 Increment button Right move button 7 6 Set button 5 Release button 4 Decrement button 3 Left move button 2 Background light button 1 Output control socket

user-defined delay and timing plan shooting The device support to control different brand or style of cameras by using different shutter connect cable.

6 7 8 9 2

Please check all included items after open the packing, if missing, please contact to dealer.

1. Timer remote control TC-252 1pc 2. Shutter connect cable 1pc 3. AAA battery 2pcs 4、 Manual(this manual) 1pc

12 Battery cover 13 Product back sticker 14 Item code

Body · Body

Page 5 of the Pixel TC-252 user manual — DC0 DC1 DC2 E3 N3 RS1 S1 UC1
Page 5 · click to enlarge
Page 5

Preparation for installation and use

The name of each part

Before use, you should read the user manual of your camera carefully; understand the manipulation and functional setting. The function setting of camera may influence the efficiency control of the camera.

DC0 DC1 DC2 E3 N3 RS1 S1 UC1

11 1213 1

Install and replace the battery

The low battery voltage icon[ ] will twinkle or the character become dim obvious when the power is not enough, that means the low battery voltage has already influence the normal work of the device, which needs to replace the battery

in time. The timer remote control uses 2pcs of AAA batteries; Please follow the steps to replace the battery if needed.

4 5 6 7 8

Input plug Shutter connect plug

1. Slide and open the battery cover.
2. According to the signs of positive [+] and negative [-] in the battery compartment to install the battery correctly .

1 Timing plan function area 2 Time display area

The icon of timing shots 12 The icon of interval time 11 The icon of exposure time 10 The icon of delay time 9 8 Low battery voltage icon 7 Delay shooting icon 6 [ ]shooting icon 4 Single shooting icon Function area 3

You should pay attention to the polarity of battery because of the wrong installation will make the device work abnormally, or even physical injury.

5 Continuous shooting within one second icon

3. Close the battery cover.

10 9 Display · Shutter connect cable · Display

Page 6 of the Pixel TC-252 user manual — Preparation for installation and use Preparation for installation and use
Page 6 · click to enlarge
Page 6

Preparation for installation and use Preparation for installation and use

Connection with the camera Open the background light of display

1. First, fix the camera on the tripod or other fixed bracket.

Press and hold the background light button for 3 seconds, the background light will be turned on.

2. Open protective cover of external shutter socket and put the shutter plug of shutter connect cable in place, then make sure it has been fixed firmly.

Open the background light and press the button twice each 6 seconds, the background light will keep lit. The background light will not be close by hand; it will turn off after 6 seconds automatically without any operation.

For most of camera shutter socket, there is mis-plug interface, please note insert direction so as to avoid damage to shutter socket. 3. Insert the input plug of shutter connect cable into the output control socket of TC-252.

The timer remote control will not be able to control the camera if the shutter connect cable hasn't insert correctly.

4. Open the camera power.

3s

Page 7 of the Pixel TC-252 user manual — 页 7
Page 7 · click to enlarge
Page 7

Sketch map for selecting function mode:

Part of the cameras can't support to wake up the external shutter, it's unable to wake up the external shutter and take photo when the camera is dormant.

2. Half-press the release button, the green light lit , and the camera is in the focusing state until the release or fullpress the button . 3. Full-press the release button, red light will light for a while, the camera start shooting .

Continuous shooting within one second function Delay shooting function

[ ]shooting function

The instruction is under the premise that the timer remote control and camera have been connected tightly, and turned on the power of camera and timer remote control. The detail instruction of remote shooting will be showing as follow.

Make sure to set the camera function to be [ ]. When the camera function is set to be[ ], it may cause continuous shooting. When the camera function is set to be[ ],the camera will shoot based on[ ]mode, it may cause underexposure or overexposure. When the camera function is set to be [ ], the camera will execute delay shooting.

1. In the power-on state , set the single shooting icon [ ] as the function one by pressing the left move button[ ]or right move button[ ].

Continuous shooting within one second

In the sleeping state, press any key to wake up timer remote control to enter single shooting mode. In the sleeping state, it can focus and shot under the single mode without wake up.

1. In the power-on state, move the activities icon to continuous shooting within

Single shooting function · Single shooting

Page 8 of the Pixel TC-252 user manual — 页 8
Page 8 · click to enlarge
Page 8

one second icon[ ]as the function one by pressing the move button[ ]or right move button[ ].

it may cause underexposure or overexposure. When the camera function is set to be[ ], the camera will execute delay shooting.

Continuous shooting within one second is one patent function which issued by Pixel limited Enterprise, it'll support spacing continuous shooting within one second and never change the single shot mode of the camera.

2. Half-press the release button, the green light lit , and the camera is in the focusing state until release or full-press the button .
1. In the power-on state , move the activities icon to [ ] shooting icon[ ] by pressing the left move button[ ]or right move button[ ].
2. Half-press the release button, the green light lit , and the camera is in the focusing state until the release or fullpress the button .
3. Full-press the release button, red indicator will be light, keep fully press the button, the indicator will flash red and green in turn. The shooting speed will be one photo per second .
3. Full-press the release button , the red light starts flashing and start timing, the timer remote control continuous output shooting signal, the red light keep flashing. Camera enter into [ ] shooting.
4. Release the release button, the camera will stop shooting.

Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], it may cause continuous shooting. When the camera function is set to be [ ],the camera will shoot based on [ ] function,

4. Press the release button again, timer remote control will stop output shooting signals, camera stop [ ] shoot.

left · [ ]shooting

Page 9 of the Pixel TC-252 user manual — 页 9
Page 9 · click to enlarge
Page 9

delay setting for adjusts the shooting numbers. Then the numbers of shooting icon [ ],number of shooting [ ]will blink at the same time. 2. Press button[ ]settings shot number can be increased, press button [ ], settings shot number can be reduced. It can be set between 1 to 99 sheets . 3. Press button[ ]enter into the delay setting of delay shooting. The delay shooting time icon[ ], delay shooting time[ ]will blink at the same time. 4. Press the button[ ], set the delay time increased, press button[ ], set the delay time reduced. It can be set between 1 to 59 seconds. 5. After set up the new parameters, press the set button, save and exit settings. When enter to the delay shooting set, timer remote control will save the previous setting. By pressing the left button[ ]or right button[ ], convert shooting numbers and delay time settings. Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced.

The differences between[ ]mode and[ ]mode are as follow: [ ]function is the release button is pressed fully and keep on, shoot every second and stop shooting until the release button is released. While[ ] function is the camera will start shooting when the release button is pressed fully until press it again, the shooting will stop. Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], the camera only shoot once but not[ ] shooting. When the camera function is set to be [ ],the camera will be continuous shooting. When the camera function is set to be [ ], the camera will be delay shooting once.

The delay shooting function of TC-252 can user-defined the delay time and shots.

1. In the power-on state, move the activities icon to delay shooting icon[ ] by pressing the move button[ ]or right move button[ ]. Press the set button entering the

Delay shooting · Delay shooting setting · left

Page 10 of the Pixel TC-252 user manual — 页 10
Page 10 · click to enlarge
Page 10

Operate the delay shooting

When the camera function is set to be [ ], the camera will perform one or more delay shooting. When the camera lens focus function is set to be [ M ],the camera will not execute focusing action if half-press the release button of the timer remote control. When the camera lens focus function is set to be [ A ], even receiving the shooting signal the camera will not shoot at the moment when most of camera don't seize focus.

1. Press the left button[ ]or right button[ ], move the activity icon to the delay shooting icon[ ]. 2. Half-press the release button, the green light lit, and the camera is in the focusing state until the release or full- press the button. 3. Full-press the release button, timer remote control start to delay countdown, red indicator blink quickly and enter to the delay shooting mode. 4. When countdown is completed, timer remote control will follow the setting shots output a signal per second to control shooting. When running the delay shooting, press the launch button again, the delay shooting will stop. Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], it will start continuous shooting. When the camera function is set to be [ ],the camera will shoot based on [ ] function, it may cause underexposure or overexposure.

Timing plan for shooting

1. In the power-on state, move the functional activities icon to the delay timing program icon[ ]by pressing the left move button[ ]or right move button[ ]. 2. Press the set button, enter the delay time for ‘second bit’ setting.
3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , “ exposure time ” , “ interval time ” , “ shots number ” as the sketch map.

“ ” “ ”

Delay time setting

Page 11 of the Pixel TC-252 user manual — 页 11
Page 11 · click to enlarge
Page 11

“ ” “ ” “ ” delay time , interval time , shots number as the sketch map.

Delay time of timing

Delay time of timing plan--minutes setting

Delay time of timing plan--seconds setting

Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced.

Exposure time of timing

time of timing Exposure

Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings.

4. Press the set button, save and exit settings.
1. Press left move button[ ]or right move button[ ], move timer remote control’s activities icon to the exposure timing program icon[ ].
1. Press left move button[ ]or right move button[ ], move timer remote control’s activities icon to the interval timing program icon[ ]. 2. Press the set button, enter the time for second bit ” setting.
2. Press the set button, enter the time for “ second bit ” setting.
3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , “ ” “ ”
Show 25 more labels / short text on this page
The shot number · Exposu · -re time · of timing · of timing · Delay · Interval · plan setting · plan setting · time · time · of timing · of timing · plan setting · plan setting · plan--hours setting · Exposure · time of timing · plan--hours setting · plan--minutes setting · plan--seconds setting · Exposure time setting · Interval time setting · exposure · interval “
Page 12 of the Pixel TC-252 user manual — 页 12
Page 12 · click to enlarge
Page 12

Press button 3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , “delay time”, “exposure time”,“shots number” as the sketch map.

“ ” “ ”

2. Press the set button, entering to set the number plan to shot. [ ]setting shot number can be increased, press button [ ], settings shot number can be decreased. It can be set between 1 to 99 sheets.
3. By pressing button[ ]or[ ],enter into the setting for delay time and “ exposure time ” , “ interval time ” as the shown picture.

Interval time of timing

time of timing Interval

Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings.

4. Press the set button, save and exit settings.

Search the timing plan

The shot number setting

1. Press left move button[ ]or right move button[ ],move timer remote control’s activities icon to the timing plan icon which can check the related timing project. 2. When check the related projects, if need adjust the parameters, only press the set button to enter the relevant project settings, press the set button again to exit and save your setting. Sequence to move the icons showed as below.
1. Press left move button[ ]or right move button[ ], move timer remote control’s activities icon to the icon of timing shots [ ].
Show 19 more labels / short text on this page
Exposu · -re time · The shot number · of timing · of timing · plan setting · plan setting · Interval · time · Delay · time · Interval plan--minutes setting · time of timing · of timing · of timing · plan--hours setting · plan--second setting · plan setting · plan setting
Page 13 of the Pixel TC-252 user manual — 页 13
Page 13 · click to enlarge
Page 13

The following examples illustrate the timing plan running: delay time[ ] = 5 seconds, exposure time[ ] = 1 second, shooting interval[ ]= 6 seconds, shooting number[ ] = 3.

1. Press the left move button[ ]or right move button[ ], move to any icon among the timing plan shooting area.

Focusing output Shooting output

2. Press the timing start/stop button[ ], the timer remote control will execute timing plan, indicator flash red once and task start executing.

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Press the timing plan start/stop button[ ] of timer remote control before the timing plan executing completely, the timer remote control will stop regularly scheduled executing. When executing the timing plan shooting, it can take single shot by pressing the release button and would not influence the timing plan.

Show 6 more labels / short text on this page
Delay shoot · Singl e · shoot · -ing function · -ing func tion · Execute timing plan
Page 14 of the Pixel TC-252 user manual — PIXEL TC-252 Specifications
Page 14 · click to enlarge
Page 14

PIXEL TC-252 Specifications

Standby time: More than 3 years Using battery: 1.5V×2AAA Dimensions(W×H×D):149mm×49.5mm×24mm Weight(with batteries):70.5g

Now you can start to use unique high-performance PIXEL product TC-252. If you have any questions, you can contact the local distributor. Or visit the website http://www.pixelhk.com

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Pixel TC-252

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Pixel TC-252

Be the first to ask — other owners or our team will answer.

Original document

Pixel TC-252 manual PDF

14 pages·1.3 MB·Miscellaneous·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…