











This household sewing machine meets the requirements of IEC/EN 60335-2-28 and UL1594.
SHOCK: • Sewing machines must never remain unattended when the plug is in the socket. Always remove the plug from this sewing machine immediately after use and before cleaning, removing cover panels from it, or lubricating the machine or performing other maintenance work as specified in the instructions.

FOR EUROPE ONLY: This device may be used by children aged 8 years or more and by persons with reduced physical, sensory or mental abilities or lack of experience and knowledge if they have received super vision or instructions to use the apparatus safely and understand the dangers associated with it. Kids aren't allowed to play with the device. Cleaning and maintenance of users should not be performed without supervision by children. In normal conditions of use, the sound level is less than 75dB(A). The machine may only be used with a pedal of the type "FR5' manufactured by Shanghai Bioao Precision Mold Co., Ltd.
FOR OUTSIDE EUROPE: This sewing machine is not intended to be used by persons (including children) with reduced physical, sensory or mental abilities, or lack of experience and knowledge, if they have not been supervised or instructed for the use of the sewing machine by a person responsible for their safety. Children should be monitored to ensure that they do not play with the sewing machine. In normal conditions of use, the sound level is less than 75dB(A). The machine may only be used with a pedal of the type "FR5' manufactured by Shanghai Bioao Precision Mold Co., Ltd.
PERFORM SERVICE TO DOUBLE ISOLATED DEVICES In a double insulated product there are two insulation systems instead of earthing. Double insulated devices have no grounding device and should not be added to the apparatus. Repairing a double insulated product requires the highest degree of accuracy and thorough knowledge of the system, and may only be carried out by expert technicians. The spare parts for double insulated products must be identical to the components in the product. A double insulated product is marked with the words "DUBBLE ISLAHON OR ACTIVE DUBBLE RANGE'.




















3 4 5 6 7 8 9 10 11
Front 1. Valve with stitch chart and button gauge 2. Wire-recording slots 3. Thread cutter 4. Connection Sensormatic node hole foot 5. LED lighting 6. Built-in wire insert 7. Needle bar 8. Wire guide 9. Plate 10. Washing lid 11. Free arm 12. Sewing foot 13. IDTTM system 14. Press foot bar and press foot holder 15. Needle screw 16. Press footlighter (7.5) . . 7RHWVHQ HQ .JUDÀVFC . Handwheel 19. Main switch, power cord connections and foot pedal 20. Slide for sinking the transporter 21. Connection for knee lever (4.2)
Parts Top 22. Pre-voltage disc for re-run and wind up of coil 23. Rinse guide for rewinding 24. Wire guide 25. Rinse wire guides 26. Subwire cutter 27. Rinse guide and coil shaft 28. Extra yarn pen 29. Yarn discs 30. Yarn pen 31. Wire voltage 32. Wire lever
24 23 22 25 26 27

29 28 30 31 32
1:6
Introduction

Accessory box The accessory box has special compartments for sewing feet and coils, as well as space for needles and other accessories. Keep the accessories in the box so you can always have them within reach. 33. Space for accessories 34. Removable tray for sewing feet 35. Removable coil holder

Accessories included 36. - Yeah, yeah. Sideguide 38. Felt ring 39. Screwdriver 40. Torn blade 41. - Oh, no. Yarn disc, large 43. Yarn disc, average size 44. Yarn disc, small 45. Universal tool 46. Rinse 47. Knee lever (4.2)



1:7
Introduction · 38 37 36

1:8
Sewing feet · Introduction

1:9
Useful stitches · Introduction

1:10
Introduction




* This stitch makes a more decorative attachment than st 1.
1:11


1 You have an optional ball foot with IDT™ system required (part no. 820613-096). 2 You need an optional bead foot 6 mm (part no. 820605-096). 3 You need an optional bead base 4 mm (part no. 820604-096). 4 You have an optional stitching foot with IDT™ system required (part no. 820676-096). 5 You have an optional cord foot with three recesses and IDT™ system required (part no. 820920-096). 6 You have an optional sewing folding foot and IDT™ system required (part no. 820931-096).
Comic (3.5 & 4.2)

Cyrillic (3.5 & 4.2*)

Outline (4.***)

* Only on Russian quilt expressionTM 4.2 sewing machine. ** Not with the Russians quilt expressionTM 4.2 sewing machine.
1:12
Introduction


















Extract 1. Place the box on a solid, flat surface. Lift the machine out of the box, remove outer packaging and lift off the cap. 2. Remove all other packaging material and the plastic bag. 3. Slide the machine's accessory box and remove the styrofoam. Note: If styrofoam is left in the accessory box, this may affect stabbing quality. Styrofoam is intended only as a packaging material and should be disposed of.

Please note: Your PFAFF® expressionTM sewing machine is built on it to deliver the best results at normal room temperature. Extremely hot and cold temperatures can affect the sewing results.
Connecting to the power supply The accessories also include the power cable and foot pedal. Please note: Before connecting the foot pedal, check if it is of the type .FR5-Pedal (see below). 1. Get the cord off the foot pedal. Turn the foot pedal. Connect the cord to the connection in the foot pedal space. Press firmly so that it is properly connected. Place the cord in the slot on the bottom of the foot pedal. Note: You only have to connect the cord to the foot pedal the first time you start using the machine. 2. Connect the cord of the foot pedal to the front contact at the bottom right side of the machine (A). 3. Connect the power cable to the rear contact, at the bottom right of the machine (B). Put the plug in the socket. 4. Turn the ON/OFF switch on ON to turn on power voltage and light (C).

2:2

Store the machine after sewing 1. Turn off the main switch. 2. First pull the power cable out of the socket and then off the machine. 3. Remove the plug from the foot pedal cord. Wind the cord to the foot pedal if you want to store it. 4. Store all accessories in the accessory box. Slide the box onto the machine to free arm. 5. Place the foot pedal in space above the free arm. 6. Place the protective cap on the machine.
LED lighting On your machine are LED lights that distribute the light evenly across the working area without shadow.

Free arm To use the free arm you need to remove the accessory box. When the box is attached, a hook holds the accessory box to the machine. Slide the box to the left to remove it.
Wire cutter Pull the wire as shown from back to front to use the thread cutter (A).
Yarn pens Your sewing machine has two yarn pins: a head thread pen and an extra yarn pen. The yarn pins are suitable for all types of yarn. The main yarn pen is adjustable and can be used in a horizontal position (the thread is rolled off the clasp) or in a vertical position ( the screw turns). Use the horizontal position for normal yarn and vertical position for large reels or yarns with special properties.

Horizontal position Place an appropriate yarn disc and the clip on the yarn pen. Make sure the thread is rolled over the top and then slide a second yarn disc onto the pen. Use a yarn disc that is slightly wider than the screw. Use a smaller yarn disc for the clasp in narrow thread pads. Use a larger yarn disc for the floppy.

The flat side of the disc must be pressed firmly against the clasp. There must be no space between the yarn disc and the screw.
2:3
Small Yarn Disc · Large Yarn Disc

Vertical position Lift the yarn pen to vertical position. Slide the large disc on it and place a felt bottom underneath the clasp. This prevents the yarn from being removed too quickly. Do not put a yarn disc on the yarn pen as it will stop turning.
Extra yarn pen The extra yarn pen is used when you want to wind up a coil from a second thread strap or for a second screw when sewing with a twin needle. Raise the extra yarn pen. Slide a large yarn disc on it and place a felt bottom under the clasp.
Head yarn pen in vertical position
Additional yarn pen and main yarn pen in vertical position
Run the machine in Make sure that the sewing foot and needle are in the highest position. 1. Slide the yarn onto the yarn pen and fasten it with a suitable yarn disc. 2. Pull the wire forwards through the conductor (A). Pull the wire from the right underneath the coil guide (B) on the pre-voltage disc (C). 3. Row the wire down through right recess slot and then up through left insertion slot. 4. Insert the wire from the right into the wire lever (D) and down in the left insert slot to the thread guide at the needle (E). 5. Insert the needle.
A C
B
D
B
E
quilt expressionTM 4.2
2:4

Wired insert The wire insert allows you to automatically insert the thread into the needle. If you want to use the wire insert, the needle must be in its upper position. In addition, we recommend that you lower the sewing foot. 1. Use the lever to pull down all the way. The recess hook (G) is swayed through the needle eye. 2. Place the thread from the back over the hook (H) and under the insert hook (G). 3. Gently reverse the wire insert. The hook pulls the thread through the eye of the needle and forms a loop behind the needle. Pull the loop out behind the needle. Note: The wire insert is designed for needles no. 70-120. When using needles with no. 60 or smaller, a sword needle, twin needle or triplet needle. There are also some optional sewing feet where you have to insert the thread by hand.

Run the twin needle Change the usual needle with a twin needle. Make sure that the sewing foot and needle are in the highest position. 1. Slide the yarn onto the yarn pen and fasten it with a suitable yarn disc. Raise the extra yarn pen. Slide a large yarn disc and felt base on the pen. Place the second thread on the yarn pen. 2. Pull the wires forwardwards through the wire guide (A). Pull both wires from the right underneath the coil wire guide (B) on the pre-voltage disc (C). 3. Row the wire down through right recess slot and then up through left insertion slot. Make sure to lead one thread along the left side and another wire along the right side of voltage disc (D). 4. Insert the wires from the right into the wire lever (E) and down in the left insert slot. Make sure that one thread passes through the wire guide near the needle and the other thread on the outside. Also, make sure the wires don't twist together. 5. Put the needles in. Note: If you use special yarns (such as metallic yarn), the weight and irregular surface increase the thread tension. By lowering the tension, you will prevent the needle from breaking.

B
Rinse
Rinse from horizontal position 1. Place an empty coil on the flush shaft, with the logo up. Use only the original PFAFF® coils that have been approved for this model. 2. Place the screw on the yarn pen in horizontal position. Slide a yarn disc firmly against the yarn pen. 3. Pull the wire forwards through the conductor (A). Pull the wire left over the coil guide for flushing (B) and then through the underwire conductors (C) at the back. Note: Make sure the wire is properly drawn into the pre-voltage disc for proper thread tension. 4. Run the wire from inside out through the slot in the coil (D). 5. Push the coil guide to the right to rinse. A pop-up will appear on the screen to tell you that reels are active. Press the foot pedal to wind up the coil. When the coil is full, the rinse goes slower and stops automatically. The pop-up is closing. Remove the coil and cut off the wire using the lower-wire cutter (E).
D

Rinse through the needle Make sure that the sewing foot and needle are in the highest position. Rinse only through the needle with a metal presser foot. Raise the thread from the needle, under the sewing foot, up through the left insert slot and through the subwire guides (C) Then follow steps 4 and 5 above.
2:6


Place the coil 1. Remove the flush cover by sliding it towards you. 2. Place the coil in the flush house with the mark pointing upwards. The wire should roll down from the left side of the coil. The coil will turn counterclockwise when you pull the wire outwards. 3. Place your finger on the coil to prevent it from turning if you pull the wire firmly to the right and then turn left in the tension spring (A) until it clicks into place . 4. Continue with the repositioning around (B) and towards the right side of the wire cutter (C). Put the lid back on the flush house. Pull the wire to the left to cut it off. Note: The sink cover can be used as magnifying glass.

IDT™ system (built-in double transport) For smooth processing of each type of fabric, PFAFF® expressionTM machine offers the ideal solution: the IDTTM system (Built-in Double Transport). As with industrial machines, the IDTTM system ensures simultaneous dust transport from both below and above. The material is transported accurately, so seams in thin fabrics such as silk and rayon no longer wrinkle. The dual transport of the IDTTM system ensures that the layers do not shift during sewing, so that the quilt layers remain well on each other and ensure a perfect connection between fabrics with windows or stripes.
The IDT™ Enable system Important: For all your sewing with it IDT™ system you can only use sewing feet with a recess on the back (D). Bring up the sewing foot. Press the IDTTM system down until it clicks.
The IDT™ disable system Bring up the sewing foot. Hold the IDTTM system by ribbed grip with two fingers. Pull down the IDTTM system and then push it off you to slowly raise the IDNTM system.
2:7

Electronic knee lever (4.2) Your machine is equipped with an electronic knee lever that allows you to adjust the height of the sewing foot. Insert the knee lever into the sewing machine in the opening provided for. The flat side should point up. Turn the pressure plate to a comfortable knee height (A). If you push the knee lever to the right, the foot goes up. Now you can conduct the fabric with both hands. If you want to remove the knee lever, pull it straight out of the opening.


Needles The sewing machine needle plays an important role in successful sewing. Use only high quality needles. We recommend needles of system 130/705H. The needle box that comes with your machine will show you needles in the most used sizes.
Universal needle (B) Universal needles have a slightly rounded tip and are available in many different sizes. For general sewing in many different types and thicknesses.
Stretch needle (C) Stretch needles have a special weld to remove skipped stitches when there is rack LQ.GH.V.W.I.]LW.M.L.LS.H.Ls.H Marked with a yellow stripe.
Embroidery needle (D) Embroidery needles have a special weld, a slightly rounded tip and a slightly larger eye to prevent damage to yarn and materials. Use them with metallic and other special yarns for embroidery and decorative sewing. Marked with a red line.
G
H
Denim needle (E) Denim needles have a sharp point to pierce through dense woven fabrics without the QDOGJHUEXLJW.19RRU & DQYDVS' GHQLPPLURRAEHU
Note: Change the needle regularly. Always use a straight needle with a sharp tip (G). A damaged needle (H) can cause stitches to be missed, needles to break or the thread to break. A broken needle can also damage the stitch plate. Do not use asymmetric twin needles (I); it may damage your sewing machine.
Sword needles (F) The sword needle has wide wings next to the needle to pierce holes in the fabric when sewing entredeux and other lace stitches on natural fabrics. Reduce the stitch width for optimal results.
2:8

Change a needle 1. Use the hole in the universal tool to hold the needle. 2. Unscrew the needle screw. Use the screwdriver if necessary. 3. Remove the needle. 4. Insert the new needle with the tool. Push the new needle upwards with the flat side of you until it cannot continue. 5. Turn the needle screw as much as possible.
Sinking the transporter You can bring the transporter down by moving the switch on the front of the sewing machine to the left. If you want to raise the transporter, move the switch to the right.
Remove the sewing foot Push down the sewing foot until it comes loose from the sewing-foot holder.
Attach the presser foot Place the sewing foot under the presser holder so that when the sewingfoot is lowered, click on the pressers' foot holder. Please note: Check that the sewing foot is securely attached by raising the sewing base.
2:9

Keys for quilt expressionTM 4.2
9 10 12 14 13 15 16 17
18 19 20 21 22 23 24
Needle up/down with indicator (1) Press this button to move the needle up or down. The needle stopper position is adjusted simultaneously. When the needle is turned on downwards, the pictogram is illuminated, the needle inserts into the fabric and the foot rises to swivel height. Of course, you can also use the foot pedal to lift or lower the needle.
Sew back (7) with indicator (5) Press the button before you start sewing if you want to sew backwards permanently. The reverse sewing indicator (5) will light up and the machine will sew backwards until you press the button again. When pressing the button while sewing, the sewing machine sews backwards as long as you hold down the key. The reverse sewing indicator is illuminated when the reverse sewing key has been pressed. The reverse sewing key is also used when sewing buttonholes, programmed attachments, stop stitches and tapette cordon stitches to go back and forth between parts of the stitches.
Start stitching (2) When you have stopped sewing in the middle of a stitch, press "start again to sew from beginning of stitch without having to re-run any previous settings. If you press the button . . start again .
Indicator programmed attachments (6) The indicator for the programmed attachment will be lit to indicate that one or more attachments options are activated. The indicator will remain on until the attachment options are no longer used.
Speed control (3) Press the speed button to sew slower. A SLFWRJUDP.SHWJUDÀVFCGLVSOD\ same JHHIWDDQ WEBRHODQJ]DDP Hold the speed key long and use the wheel (16) to change the sewing rate. Please note: You cannot select a speed higher than the default speed.
Immediately attached (8) Pressing the attachment button while sewing, your machine sews off some stitches and stops automatically.
Alternate between presser foot up and extra high (9) Raise the sewing foot and place needle in highest position. Press the key again; the presser foot goes up to the extra high position.
Cut wires with indicator (4) Press the button when not sewing; then the sewing machine cuts off the top and bottom thread and raises the needle and foot. To cut the thread before moving to the starting position of the next stitch, press cutting off . The wire cutting indicator is about to light.
2:10
25 26 27

Alternate between foot down and turning position (10) Lower the foot all the way down. Press the key again to raise the presser foot up to swing height. The sewing foot is automatically lowered when you start sewing.
Direct selection (17) By pressing one of the keys from 0 to 9, or by using a combination of those keys, select immediately the stitch associated with that number.
F1 - Function 1 (18) The F1 key is used to configure the tapering program. The key is also used to repeat buttonholes and to disable . . All selections are ZHHUJHJHYHQ...RSSKHWJUDÀVFC MGLVSOD\By sequence, the F1 key is used to select a set of characters.
Start/stop (11) Press this button to start and stop the sewing machine without using the foot pedal. Press the button once to start and again to stop.
Graphical display (12) 2S.H.H The stitches are shown in true size.
F2 - Function 2 (19) The F2 key is used to set the options for cutting off attachments and wires, and in series F2 is used for selecting a font. All selections are shown on KHWJUDÀVFC .
Stitch width or position of stitch (13) Enlarge or reduce the stitch width by + and -. Press the alternative key (15) to see the position of the selected stitch. Use the + and - keys to change stitch position.
Info key (20) Press this button to turn on or off the display of recommendations.
Pitch length or stitch density (14) Enlarge or reduce stitch length by + and -. Press the alternative key (15) to view the density setting of cordon stitches. Use the + and - keys to change the density of the selected stitch.
Settings Menu (21) Press this button to open the machine settings menu.
Vertical mirror (22) To mirror stitches and series vertically.
Alternatives (15) When selecting a decorative stitch, the width and length settings are displayed on KHWJUDÀVFCSOGLVSOD\. • RRU "RRU"RS
Horizontal mirror (23) To mirror stitches and sequences horizontally.
Personal stitch or load sequence (24) Press this key to load a personal stitch or sequence.
Save personal stitch or sequence (25) Press this key to save a stitch or sequence in machine memory.
Wheel (16) 0HW.H.H.]H.W.W The wheel has arrow keys up and down, arrow key left and right and the center of the wheel is an OK-key. The wheel has various functions, such as steps between stitches, setting the size of a buttonhole and moving between options in the Settings menu.
Clear (26) For removing single stitches in a series, or from personal stitches and sets.
Series (27) Press this key to open series.
2:11


Needle up/down with indicator (1) Press this button to move the needle up or down. The needle stopper position is adjusted simultaneously. When the lower needle is switched on, the pictogram is illuminated, the needle will put into the fabric. Of course, you can also use the foot pedal to lift or lower the needle.
Sew back (7) with indicator (5) Press the button before you start sewing if you want to sew backwards permanently. The reverse sewing indicator (5) will light up and the machine will sew backwards until you press the button again. When pressing the button while sewing, the sewing machine sews backwards as long as you hold down the key. The reverse sewing indicator is illuminated when the reverse sewing key has been pressed. The reverse sewing key is also used when sewing buttonholes, programmed attachments, stop stitches and tapette cordon stitches to go back and forth between parts of the stitches.
Immediately attached (2) Pressing the attachment button while sewing, your machine sews off some stitches and stops automatically.
Indicator programmed attachments (6) The indicator for the programmed attachment will be lit to indicate that one or more attachments options are activated. The indicator will remain lit until the attachment options are no longer used.
Start again (3) When you have stopped sewing in the middle of a stitch, press "start again to sew from beginning of stitch without having to re-run any previous settings. If you press the button . . start again .
Cut wires with indicator (8) Press the button when not sewing; then the sewing machine cuts off the top and bottom thread and raises the needle and foot. To cut the thread before moving to the starting position of the next stitch, press cutting off . The wire cutting indicator is about to light.
Speed control (4) Press the speed button to sew slower. (HQSLFWRJUDP.RS.KHWJUDÀVFC.GLVSOD\ same JHHIWDDQ.) how slowly your sewing machine will sew. Hold the speed key long and use the wheel (13) to change the sewing rate. Please note: You cannot select a speed higher than the default speed.
2:12

Graphical display (9) 2S.H.H The stitches are shown in true size.
F2 - Function 2 (16) The F2 key is used to set the options for cutting off attachments and wires, and in series F2 is used for selecting a font. All selections are shown on KHWJUDÀVFC .
Stitch width or position of stitch (10) Enlarge or reduce the stitch width by + and -. Press the alternative key (12) to view the position of the selected stitch. Use the + and - keys to change stitch position.
Info key (17) Press this button to turn on or off the display of recommendations.
Pitch length or stitch density (11) Enlarge or reduce stitch length by + and -. Press the alternative key (12) to view the density setting of cordon stitches. Use the + and - keys to change the density of the selected stitch.
Settings Menu (18) Press this button to open the machine settings menu.
Horizontal mirror (19) To mirror stitches horizontally.
Alternatives (12) When selecting a decorative stitch, the width and length settings are displayed on KHWJUDÀVFCSOGLVSOD\. • RRU "RRU"RS
Personal stitch or set of loads (20) Press this key to load a personal stitch or sequence.
Personal stitch or set save (21) Press this key to save a stitch or sequence in machine memory.
Wheel (13) 0HW.H.H.]H.W.W The wheel has arrow keys up and down, arrow key left and right and the center of the wheel is an OK-key. They have various functions, for example steps between stitches, set the size of a buttonhole and move between options in the Settings menu. Attach your selections with the OK icon in the middle of the wheel.
Clear (22) For removing single stitches in a series, or from personal stitches and sets.
Series (23) Press this key to open series.
Direct selection (14) By pressing one of the keys from 0 to 9, or by using a combination of those keys, select immediately the stitch associated with that number.
F1 - Function 1 (15) The F1 key is used to set the tapering program. The key is also used to repeat buttonholes and to disable . . All VHOHFWLHV .ZRUGHQ . ZHHUJHYHQ .RSSALKHW .JUDÀVFK display. In series, the F1 key is used to select a set of characters.
2:13




2:14

Settings Menu In the Settings menu you can cancel automatic settings and manually customize machine settings, sound settings or screen settings. Open the menu by pressing the Settings button and select the setting you want to adjust with arrow keys up and down on the wheel. Use the arrow keys left and right to adjust values and activate settings or open a list of choices by pressing OK. A closed box means it is activated, an empty box means that it is not enabled. Note: If a setting cannot be combined with a previously selected setting, the edges of that box are dotted.
There are two icons that appear next to some setting alternatives.

This icon shows you that the setting is retained until you select another stitch.
This icon shows you that the setting is retained until you turn off the machine. No icon means that this setting is retained until you disable the setting.
Press the Settings menu button again to exit the menu.
Wire voltage Your sewing machine electronically sets a wire tension for the selected stitch. Depending on the fabric, quilting, yarn etc. may need to adjust the voltage. Use the arrow keys left and right on the wheel to adjust the wire voltage. The changes only affect the selected stitch. The setting returns to default when selecting another stitch.
Stitch width protection Select this function when using a stitch plate or presser foot for straight stitches, to secure the needle position for all stitches in the middle to prevent damage to the needle, sewing foot and stitching board.
Press the info key in sewing mode. The stitch width protection icon is displayed. When you re-enable the machine while this setting is enabled and for any stitch selection that is not a straight stitch, a pop-up window will inform you that the right stitch has been set. Deselect stitch width protection to sew normal again. Note: Twin needle and stitch width protection cannot be used simultaneously.
In sewing mode press the info key to see the currently selected wire voltage.
Twin needle Activate the twin needle program and use arrow keys left and right on the wheel to adjust the width of the twin needles. When the size for the twin needle is selected, the width of all stitches is limited to that needle size because the needles can otherwise break.
Dynamic spring foot 6D (4.2) The dynamic springing sewing foot goes up and down at each stitch to hold the fabric on the stitch plate while making the stitch. Use swing height in the Settings menu for adjustment to different fabric thicknesses. Note: Dynamic springing foot 6D is recommended for use with straight stitches. Activate stitch width protection.
Press the info key in sewing mode. The icon with recommendations for the twin needle is displayed. The settings will remain until you deselect the twin needle width. Note: Twin needle and stitch width protection cannot be used simultaneously. A warning pop-up will appear when you select a stitch that is too wide for the set twin needle.
2:15

Spring foot free-motion (4.2) Enable this to turn the machine into Spring foot free-motion mode. Sink the transporters. A spring foot goes up and down at each stitch to hold the fabric on the stick plate while making the stitch.
Press footprint (4.2) In most cases, you do not need to adjust the press footprint. To improve the result when using special techniques, you need to adjust the pressure. Use the arrow keys left and right on the wheel to adjust the pressure. The higher the number, the more pressure on the fabric. The value can be adjusted between 0 and 9 in steps of 0.5. Your manual setting will be cancelled when you turn off the machine. Note: If you want to change the press footprint for a whole series, then bring the sequence to sewing mode and change the settings there.
Press the info key in sewing mode. The icon . . spring foot free-motion . is shown instead of the recommendation for the sewing foot. A pop-up will tell you that spring foot free motion is active when you turn on the machine. Please note: The free-motion foot with open toe is optional HQ.NDQ.ZRUGHQ.D.QJHVFKDIWBELM.XZ.Z.ODWHOLMNHALMRIÀFLsOH. PFAFF® dealer. Do not use the foot if Sensormatic free-motion is switched on as the needle may damage the sewing foot. The open foot for free-hand quilts and the other jump feet with light grey plastic housing can also be used to embroider.
Automatic presser (4.2) The automatic press footlighter is enabled when the function is selected. The sewing foot is raised to swivel height, for example if you stop sewing with the needle down. When the function is unselected, the foot remains in low position - even if the machine stops with the needle down.
Sensormatic free-motion (4.2) Enable this to set the machine in Sensormatic free-motion mode for presser foot 6A. Sink the transporters.
Balance When sewing on special fabrics or when performing a special technique you sometimes need to adjust the balance. First sew a stitch on a SURLÁDSMH.H.XLN.H When you start sewing again, the balance is adjusted. The changes only affect the selected stitch. The setting returns to default when selecting another stitch.
Press the info key in sewing mode. The icon . . When sewing free-motion at low speed, the foot goes up and down with each stitch to keep the fabric correctly on the stick plate while making the stitch. At a higher speed, the sewing foot floats over the fabric while sewing. The substance must be moved manually. When you turn the machine on, a pop-up will tell you that sensormatic free motion is active.
Language With the arrow keys left and right you can change the language of all text in your machine.
Rotation position (4.2) The press foot height can be adjusted if the machine is set to free-motion (sew from free hand). In the Sensormatic free-motion mode, the fabric can move freely under the sewing foot. It may occur that stitches skip when your fabric moves up and down while you are sewing. Lowering the rotation position reduces space between the sewing foot and fabric, preventing stitches from being missed. Please note: Be careful to lower the rotation position. The fabric must always be able to move freely under the sewing foot.
Audio alarm Turn on or off all alarms from the machine. The default setting is on.
Contrast 3DV .KHWJUDVWFKJUDAVKJUDÀVFKGLVSOD\DDDQ The value can be adjusted between -20 and 20 in steps of 1.
Software version Check the software version of your sewing machine.
2:16















'H.Q.DDLPRGXV'LV.V.VGH Here you will find all the basic information that you need to start sewing. This is also the menu where you can adjust your stitch settings. The straight stitch is selected by default.
Sew Mode - Overview 1. Selected stitch number 2. Sketch field 3. Stitch width/stitch position 4. Stitch length/stitch density 5. Tape program 6. Detachment Options

Select a Stitch By pressing one of the direct selection keys, select that stitch number immediately. Press two or three digits quickly in succession to select a stitch of 10 or higher. If the stitch number does not exist, you will hear a beep and the first digit entered will be selected as a stitch. Use the keys up and down on the wheel to move from one stitch to another.
Sewing advice Press the info key to call up sewing recommendations for the currently selected stitch. Press the button again to hide information. 7. Recommendation/adjustment for the needle

3:2

Modify Stitches Your machine sets the best settings for each selected stitch. You can make your own adjustments to the selected stitch. The setting only affects the selected stitch. Your changed settings will be restored to default when you select another stitch. The changed settings are not automatically saved when you turn off the machine. The set stitch width and the stitch length can be seen next to the icons for each adjustment. When you try to exceed the minimum or maximum width and length settings, there is a sound warning. Note: The digits are marked when the setting is changed.
Wire voltage (5) For nice and durable stitches you should check that the top wire tension is well adjusted; for general sewing, this means that the threads WXVVHQ .GHALWARVWRÁDJHQ OKAYHUNQRSHQ If the base wire is visible on the top of the fabric, the upper wire voltage is too high. Lower the overhead voltage. If the upper wire is visible on the bottom of the fabric, the top wire voltage is too low. Increase the voltage of the upper wire. For decorative stitches and buttonholes, the top thread should be visible at the bottom of the fabric.
Your sewing machine electronically sets a wire tension for the selected stitch. See page 2:16 for manual change instructions.
Stitch width (1) Enlarge or reduce the stitch width by + and -.
Length of stitch (2) Enlarge or reduce stitch length by + and -. If you extend a zigzag stitch or decorative stitch, the whole st will be longer. If you extend a cordon stitch whose density can be adjusted, the whole stitch will become longer but its density will remain the same.
Position (3) Press the alternative key to see stitch position instead of stitch width. Use the + and - buttons to move the stitch to the left or right. Note: This is only possible when using a stitch smaller than 9 mm. You can reduce the stitch width to narrow the stitch if necessary.

Punctuation (4) When cordon stitches press the alternative key to see density instead of stitch length. Now the density is adjusted with keys + and - of stitch length. The density does not affect the actual length of the whole stitch. Note: This is often used in special yarn and when choosing a less dense cordon stitch. If you have selected a buttonhole, KHWJUDÀVFC GLVSOD\ .VWDQGDDUG'GHALFKHLGVLQVWHOOLQJJJQ shall show position of stitch length.
Press the alternative key to view stitch position and density

3:3
Sew

Mirror To mirror stitches or sets horizontally, press the horizontal mirror key.

For 4.2: To mirror vertically, press the vertical mirror key.
Detachment Options With the attachment options you can program attachments at the beginning (A) and end (B) of stitch. 1. Press the F2 key to open the display of the attachment options. 2. Use the wheel to move from one option to another and press OK to select which functions you want to use. 3. Once you have made your selections, close the view by pressing the F2 button again. Mini-detachment icons (D) on the JUDÀVFCSGLVSOD\JHYHQ .DDQ The selections will remain until you unselect them. Note: For instant attachment use the attached key on the front of the machine.

Sew with attached options selected 1. Attaching at the beginning (A) is performed as soon as you start sewing. 2. Press the reverse sewing button to enable attachments at the end (B). The programmed attachment indicator is burning. The machine completes the stitch and makes a suture. When cutting wires (C) is programmed, the machine automatically cuts off the threads after the attachment at the end. The needle and the sewing foot are going up. Note: Stop sewing and press the reverse stitch button twice to activate reverse sewing. The reverse-sew indicator is going to light up. No sew-off is performed. Press the reverse sewing button while sewing backwards to turn on attachments at the end. Both the reverse sewing indicator and the programmed attachment indicator will start burning. To start sewing forward again, stop sewing backwards and press the reverse stitch button. No indicators are burning and no attachments are being performed. 3. To disable the attachment options, use the wheel to go to different options and press OK for each option you want to unselect.
3:4
Sew

Taper programme In the case of tapering, the width of the stitch is increased or reduced during sewing for (a) symmetrical shapes. 1. Open the display of the tape program with the F1 key. 2. Use arrow keys left and right on the wheel to select tapering at the beginning or end. Press OK to switch the setting on or off. 3. Hold OK long to open a view with different angle options for tapering at the beginning or end. With the arrow keys select the angle you want to allow your work taps to run and press OK to select the corner. 4. Press the F1 button again to close the display of the taper. There are PLQLSLFWRJUDPPHQ$ .RSJUDAVFKHÜDÜDÖGLVSOD\By showing you whether tapering is enabled at the beginning or at the end. 5. When tapering is enabled at the beginning and end, stitch width starts at 0 when you start sewing. The stitch is wider until the selected width of stitch is reached. Sew your desired length and press the reverse sewing button. The width is reduced to 0 mm. Note: Tape can be applied to almost all stitches. When you try to open the display of the taper for a stitch that cannot be applied, you will hear an alert.




Speed control 1. Keep the speed key pressed long to open a pop-up where you can use left and right arrow key on the wheel to change sewing rate. Please note: You cannot select a speed higher than the default speed. 2. Press the speed button again to close the pop-up. 3. Press the info key. An icon on the JUDÀVFCSGLVSOD\JHHIW GOH 4. Press the speed button to disable the speed control. Press the speed button again to sew with the speed you selected earlier.

3:5
Sew

Save Personal Stitch 1. You can save your personal stitches in your machine by pressing the .save button . The menu • Personal stitch or series of save • is then opened. 2. Select a blank memory with the arrow keys. Confirm your selection with OK. If the selected memory is not empty, a pop-up message will appear asking you to overwrite the previously saved stitch or sequence with the new one. Select yes or no with the arrow keys and press OK. 3. Press the Save button again to return to sewing mode. Note: Some special stitches, such as buttonholes, cannot be saved. A pop-up will tell you that when you try to save such a stitch.


Load a personal stitch 1. You can load your personal stitches by pressing the . The menu • Personal stitch or series of loading • is then opened. With the arrow keys on the wheel select the personal stitch option in the pop-up. Confirm by pressing OK. 2. Use the arrow keys to select the stitch you want to use and press OK. The stitch appears in sewing mode and is ready to be sewn. The number of the loaded stitch is a heartbeat.

Remove Personal Stitch 1. You can remove your personal stitches from your machine in loading or storage mode. 2. Select the stitch you want to remove and press the .wipe button . A pop-up message will appear asking you to really delete it. Select yes or no with the arrow keys on the wheel and press OK.

3:6
Sew

Handicraft quilting A quilt usually consists of three layers, two layers of fabric with a layer of quilt lining between them. 1. Ride the quilt top to the lining and back. 2. Insert the needle with invisible (nylon) yarn. Use rayon or cotton yarn in a stylish or matching color in the coil. 3. Click on the foot recommended by the machine. 4. Enable the IDTTM system. 5. When you sew the stitch, all you should see is the underwire. Increase the upper wire voltage as needed for desired effect.


Note: Use needle size 90 and thin, soft cotton underwire when sewing quilt stitches with a handmade appearance. You may need to adjust the wire tension depending on the fabric, yarn and intermediate filling used. Enter HHQ .SDDU .WHVWHQ ,XLW .RS .HHQ •SURHÁDSMH .YDQ .GH ,VWRI .GYH \GLH ♪X .JDD .
Recommended stitches for quilt with an andmade appearance

4.2 53 54 55 56 57 58 244 245 246 247 248 249 250 251 252 253 254
3.5 44 45 46 47 48 49 –
Stop By stopping a hole or crack before it gets bigger, you can save a garment. Choose a thin thread in a color that comes as close to the colour of your garment as possible. 1. Place your garment under the seam foot with reinforcement. 2. Select a stop stitch. 3. Start sewing above the hole and sew over it. 4. When you have sewn over the hole, press the reverse stitch button to set the length of the stitch. Your sewing machine automatically completes the stitch. 5. By default, the machine is set to repeat the same size to a stop square, you can just keep sewing. The repeat icon is marked to indicate that .toggle is enabled. Press F1 to disable .

3:7
Sew

Free hand position (7.5) When using the free-hand/stop foot, the sewing foot must be in the free hand position. 1. Disable the IDTTM system and sink the transporter. 2. Attach the free-hand/stop foot and select a stitch. 3. To switch on the free-hand position, lift up the press footlighter and push the switch (A) at the bottom of it towards you until he clicks in place. If you release the press footlighter, it will be placed in the free hand position. . . 1DDL'HQSSURHÁDSMH If necessary, you can increase the wire voltage for the desired result. 5. Start sewing. 6. To disable the position, push up a little and remove the switch (A) until it clicks in place.

For 4.2: Refer to page 2:15 for instructions on free-hand sewing with the 4.2.
Buttonholes To sew a buttonhole, first attach the right foot and then select your buttonhole. Check that the IDTTM system is disconnected. To ensure a good result, sew first on the fabric and strengthen you will use. The direction of stitches that are sewn is indicated on the screen by an arrow next to the buttonhole.
Sensormatic buttonhole When sewing a buttonhole with the Sensormatic Buttonhole foot, adjust the length of the opening to slightly larger than the size of the knot. 1. Click on the Sensormatic buttonhole foot 5A. 2. Insert the plug into the contact left over the needle area (B). 3. Use the ruler on the lid to measure your button. Set the length of the buttonhole opening with arrow keys left and right on the wheel. 4. Make sure the red arrow matches the marking on the foot (C). 5. Start sewing by pushing the foot pedal. • 'H.H.L.L,M.H,M,M'N,M-N,N,S,N-N-O-N'N-A-N. The caterpillars are sewn in the same direction. 7. The buttonhole will be automatically completed. You can repeat the buttonhole as often as you want by pressing the foot pedal.
3:8
Sew

Manual buttonhole 1- Use sewing foot 5M to sew a manual buttonhole in four steps. 2. The first caterpillar is sewn backwards. Sew the first caterpillar as long as you use the buttonhole ZLOW .PDNHQ .S .KHW .JUDÀVFC .GLVSOD\ .VWDDW , indicates which part of the button hole is sewn and in what direction. 3. Press the reverse stitch button. The machine sews the trens and the second caterpillar. When the caterpillars are equally long, press the reverse button again to sew the second trences. Please note: The repeat icon is marked to indicate that .to . to .replay . is enabled. You can repeat the buttonhole as often as you want by pressing the foot pedal. The machine stops automatically when the buttonhole is finished. Press F2 to disable .


Sew a button 1. To sew a button, remove the sewing foot and select the button stitch. 2. Sink the transporters. 3. Put the button under the press foot holder. Use the mirror function to ensure that the needle is exactly in the holes of the button and that its width is suitable for the used button. If necessary, change the width between the holes with the + and - keys. 4. You can increase or reduce the number of stitches that tie the button to the fabric in steps of two, with arrow keys left and right on wheel. 5. Start sewing. The machine sews the program for you and then closes it off and stops. Please note: Use the universal tool to make a .snipstick for your button. You can also use a button socket, which is available as an optional accessory.

3:9
Sew

Low subwire (4.2) When the coil is almost empty, the machine stops automatically and a pop-up appears on the screen. Replace the empty coil with a full and press OK on the wheel for attachment.

Main engine overload If you sew very thick fabric or if the machine is blocked while sewing, the main engine may become overloaded. The machine stops sewing. The pop-up message closes when the main engine and power supply are secure.


Remove blocked wires (4.2) Remove wires and dust from the space underneath the stitch plate. Press OK on the wheel to close the pop-up.
3:10
Sew




















The .series .of your machine allows you to create stitches and series with your own personal settings, and combine stitches with letters in sets. You can put up to 40 stitches, letters and commands in the same sequence. Save your own stitches and sequences on your machine so you can load them and sew them whenever you want. All stitches in your sewing machine can be used for series, except buttonholes, stop, taper stings, press buttons and trenches.
Series - Overview 1. Current stitch number 2. Sketch field 3. Series commands 4. Alphabets 5. Stitch width/stitch position 6. Stitch length/stitch density 7. Character Set (capital/small letter, normal/special symbols) 8. Font Selection

Create a series 1. Press the . . series . to open sequences. 2. Press the number of stitch you want to use. The stitch appears in the stabbing area. 3. Press the number of next stitch. It appears on the right side of the previously inserted stitch. Note: The current position in the stitch area is marked with a cursor. Inserted stitches are put at the cursor location. You can move the cursor through the sequence using arrow keys left and right on the wheel.
Series Commands You can program attachments, cut-off instructions and stop commands in your series. Use the arrow keys on the wheel to select a command and press OK to insert the command. The command is set to the cursor location. Commands entered are included in the series and always executed during sewing. Please note: You can enter up to 3 commands in each sequence.
4:2
Series

Use the alphabet 1. You can move the cursor with arrow keys left and right on the wheel to place it in the stitch area (2) where you want to add a letter. 2. Use the arrow key down to go through the sequence commands (3) to the alphabet (4). Select a letter with arrow keys and press OK to insert the letter. The letter is placed at the cursor location in the stitch area. Please note: The selected letter of the alphabet is marked.

Select character set and font Press F1 to set the character set (7) to upper or lower case letters, normal or special letters and symbols. Press F2 to change font (8).
Adjust text and stitches You can mirror the desired stitch, adjust its length (6) and width (5) or change density and stitch position. The adjustments work the same as in sewing mode. See page 3:3 3:5. When you have changed a value, the FLMIHUV.V.S.A.KHWJUDÀVFC MGLVSOD\ Note: The adjustments only affect the stitch at cursor position. If you return to sewing mode, all the adjustments made there will affect the whole sequence and they won't be saved.
Remove a stitch or letter from a string If you want to remove a stitch, take the cursor to that stitch and press the . Place the cursor on the left next to first position and press the .wipe button .
4:3
Series

Manage your series You can save and reload your series. Each set of memory has space for 40 stitches.
Save Series Saving your sequence goes the same way as in sewing mode. See page 3:6.
Load Series Loading your sequence goes the same way as in sewing mode. See page 3:6. Select the option . . in the pop-up . Note: When you load a sequence in sewing mode, the number of the saved series is displayed with an M before.
Remove a string The removal of your sequence goes the same way as in sewing mode. See page 3:6.
A series of sewing To sew the sequence, go back to sewing mode by pressing the .b. series .c. or pressing the foot pedal. Your sequence is ready to be screwed. The sequence is continuously sewn if no stop is programmed. Note: Changes made in sewing mode affect the whole range. However, those adjustments will not be saved if you return to series.

4:4
Series

































Clean the sewing machine Clean your machine regularly to make sure that your machine continues to work properly. The machine does not need to be lubricated (oiled). Take off the outside of your sewing machine with a soft cloth to remove any accumulated fabric or textile residue. 1HHP .KHWJUDÀVFC .GLVSOD\ .DI .PHW .HHQ .VFKRQH .

Cleaning the flush house Note: Sink the transporter and turn off the machine. Remove the sewing foot and slide open the flush cover. Place a screwdriver under the stitch plate as shown on the image and gently twist the screwdriver to unwrap the stitch board. Clean the transporter with the brush attached to the accessories.
Cleaning the flush section Clean the area under the flush house after various sewing projects or when you notice that textile remains have accumulated in the flushing unit. Remove the coil holder (A) covering the front part of the flush house by lifting it. Remove the flush house (B) by lifting it. Clean with the brush.
Be careful when cleaning the area to clean the blade of the wire cutter (C). Replace the flusher and the sink holder. Note: Do not blow air into the flush compartment area. The dust and the fluff will then be blown into your machine.

Replace the stitch plate With the transporter, place down the stitching position with the button in the slot at the back (D). Push the stitch plate down until it clicks in place. Slide the sink cover back into place.
5:2
Maintenance

Troubleshooting In this troubleshooting guide you will find solutions to problems that you can RQGHUYLQGHQJJPHQHKKKQHO1HHPSYRRU .PHHU'LQIRUPDWLH
Problem/cause of Solution General problems Is not the wire cut off with .
Remove the stitch plate and remove textile scraps from the coil section. Dust isn't being transported? Check that the machine is not set in free-motion mode from the settings menu. Check that the transporter isn't sunk. Wrong stitch, irregular or narrow stitch? Disable twin needle or stitch width protection
in the Settings menu. - The needle breaks? Apply the needle correctly as described in section 2. Attach the right needle for the substance. The machine doesn't sew? Check that all plugs are in the machine and in the socket. Check that the cord of the foot pedal is in the pedal. Push the coil guide into the sewing position. The sewing machine function keys do not respond to the touch?
The connections and function keys of the machine can be sensitive to static electricity. If the keys do not respond to touch, turn the machine ON and on again. If the problem persists, please contact your local authorized PFAFF® dealer.
The sewing machine skips crossing Have you correctly inserted the needle? Apply the needle correctly as described in section 2. Did you use the wrong needle? Use needle system 130/705 H. Is the needle crooked or bone? Insert a new needle. Did you properly pour in the sewing machine?
Check how the machine was loaded.
Is the right sewing foot used? Confirm the proper sewing foot. Is the needle too thin for the wire? Check that the needle is suitable for yarn and fabric. Does the fabric move up and down in free-motion with the needle? (Sensormatic free-motion mode, 4.2)
Lower the press foot height in the setting menu.
The top wire breaks Have you correctly inserted the needle? Apply the needle correctly as described in section 2. Did you use the wrong needle? Use needle system 130/705 H.
5:3
Maintenance

Is the needle crooked or bone? Insert a new needle. Did you properly pour in the sewing machine?
Check how the machine was loaded.
Is the needle too thin for the wire? Insert a needle big enough for the thread. Do you use poor quality yarn or yarn that is dehydrated?
Take new yarn of better quality that you bought from a RIÀFLsOH. Is the right yarn disc used? Attach a yarn disc that is the right size for the used yarn pad. Is the yarn pen in the best position? Use a different yarn pen position (vertical or horizontal) Is the hole in the stitch plate damaged? Replace the stitch plate.
The coil wire breaks Have you correctly placed the coil? Check the underwire. Did the hole in the stitch plate get damaged? Replace the stitch plate. Is the flush house clean? Remove the textile waste from the flush house and use only the original PFAFF® coils that have been approved for this model. Is the coil well excited? Rinse yarn on another coil.
The seam has uneven stitches Is the wire voltage well adjusted? Check the top wire voltage and how the machine was loaded. Do you use too thick thread or poor quality sewing yarn?
Replace the yarn.
Is the underwire evenly excited? Check the coil's excitement. Is a correct needle used? Apply an appropriate needle correctly, as described in section 2.
The sewing machine does not transport or irregularly Did you properly pour in the sewing machine?
Check how the machine was loaded.
Any fluffs piled up between the transporter's teeth?
Remove the stitch plate and clean the transporter with a brush.
Have your sewing machine checked regularly by your local official PFAFF® dealer! If you have followed these troubleshooting instructions and still have problems, EUHQJJJGHOGHFKLQH
Non-original parts and accessories The warranty does not apply to malfunctions or damage caused by the use of non-original accessories or parts.
5:4
Maintenance

We reserve the right to make changes without prior notice, in the range of accessories or adjustments to performance or design. However, such changes are always in the interests of the user of the product.
Intellectual property The patents on this product are shown on a label under the sewing machine. PFAFF, PERFECTION STARTS HERE, EXPRESSION, QUILT EXPRESSion, IDT (picture) are trademarks of KSIN Luxembourg II, S.ar.l.
When removing this product, be careful to ensure that it is recycled correctly according to the national guidelines for electrical/electronic products. Do not throw away electrical equipment as unsorted household waste, but use separate waste collection. Contact the municipality for information on the collection points. If you replace old devices with new ones, the seller may be legally obliged to take your old device back for free in order to remove it.
If electrical appliances are disposed of on landfills or dumps, dangerous substances may leak into groundwater, enter the food chain and cause damage to your health and well-being.
CE - Authorised Representative
CE - Authorised Representative
VSM Group AB, SVP Worldwide Drottninggatan 2, SE-56184, Huskvarna, SWEDEN
VSM Group AB, SVP Worldwide Drottninggatan 2, SE-56184, Huskvarna, SWEDEN

Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.