

MODEL NO.


1. Read these instructions. 2. Keep these instructions. 3 Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (Including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.A polarized plug has two blades with one wider than the other.A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the stand, tripod, bracket, or mount specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. 16. The shock hazard marking and the associated graphical symbol is provided on the bottom panel of the unit. 17. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, shall be placed on the apparatus.

Thank you for purchasing this tablet DVD player. Please read this manual carefully
before operating and reserve it for future reference. It will be helpful to you if you
encounter any operational problem.
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture, Dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the Apparatus. Dangerous high voltages are present inside the enclosure. Do not open the cabinet. Refer servicing to qualified personnel only.
To prevent electric shock, match wide blade of plug to wide slot, fully insert. ATTENTION:
This Digital Video Disc player employs a Laser System. To ensure proper use of this product, please read this operating instructions manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service location.
Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible and invisible laser radiation when open and interlocks defeated. DO NOT STARE INTO BEAM



To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.

that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology
must be authorized by Macrovision. If not, the use of this technology is only permitted for domestic use and other
limited playback uses. Reverse engineering or disassembly is prohibited.
Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
DivX:
This device incorporates copyright protection technology
that is protected by DivX, Inc. DivX, DivX Certified and associated logos are trademarks
of DivX, Inc. and used under license.
Please do not throw electronic devices into household waste
but separate them for correct recycling.
This product conforms to Emark specifications. EMARK:

PRECAUTIONS TABLE OF CONTENTS
TYPES OF DISCS PLAYABLE ON THIS PLAYER PLAYABLE FORMATS
PACKAGE CONTENTS
FRONT SIDE LEFT SIDE TOP PANEL BUTTON DEFINITION REAR SIDE HOW TO STAND
11 11 12 13 13 14 15 16 16 17
REMOTE CONTROL
KEY DESCRIPTION OF REMOTE CONTROL
FITTING HEADREST MOUNT
FITTING PORTABLE DVD PLAYER TO HEADREST MOUNT
CONNECTING THE PLAYER TO A TV SET
CONNECTING 12V DC SUPPLY USING THE EARPHONE
CONNECTING TO A DOLBY DIGITAL/MPEG DECODER OR AN AMPLIFIER WITH BUILT-IN DECODER CONNECTING TO A DOLBY DIGTAL AMPLIFIER THAT IS NOT DOLBY DIGITAL / MPEG COMPATIBLE CONNECTING TO ACTIVE SPEAKER SYSTEMS
AVP CABLE MOVIE SHARE OPERATION
TURNING ON THE POWER TURNING OFF THE POWER LOADING PLAYBACK STOP PLAYBACK PAUSE PLAYBACK PLAYING AT FAST SPEED PLAYBACK IN SLOW MOTION A-B/REPEAT PLAYBACK
26 26 27 28 28 28 29 29 29


1. DO NOT MOVE THE PLAYER DURING PLAYBACK
During playback, the disc spins at high speed. So do not lift or move the player. Doing so may damage the disc.
Before transporting the player, be sure to remove the disc and turn off the power,
then unplug the power cord.
Select a stable place upon which to site the DVD player. Do not place the player on top of a TV or color monitor. Install the player away from cassette decks or other devices which are easily affected by magnetic forces.
Do not expose this apparatus to rain, moisture, dipping or splashing and no
objects filled with liquids, such as vases, shall be placed on the apparatus.
If the player is in use, switch the power off.
We strongly advise against using the player in the front seat whilst driving. Most countries and states have laws which prohibit or severely restrict the use
of the player in the front of vehicles while driving. Do not leave the player in places where the temperature is extremely low (About-10 C or lower) or extremely high (About 60 C or higher), such as inside the vehicle or luggage compartment in midsummer. Doing so may warp the outer case or reduce the performance.

Normally clean the player with a soft, dry cloth. For tough dirt, apply some neutral
detergent diluted in 5 to 6 parts water to a soft cloth, wring out thoroughly. Wipe off the dirt, then wipe off the player with a dry cloth. Note that alcohol, thinner,
benzene, insecticides, etc., may cause the print or coating to peel off. Also avoid leaving rubber or plastic products in contact with the player for long
periods of time, as this may damage the cabinet. When using chemically treated cloths, read the cloth's instructions carefully. Always unplug the power cord from the power outlet before cleaning the player.
Unauthorized duplication, broadcast, public performance or rental of discs are prohibited by law.
The DVD player may be allowed to be used on an aeroplane at the discretion of the airline. Always conform to the instructions given with respect to the use of electonic devices whilst traveling on an aeroplane.

The discs listed on the table below can be played on this player without an adapter.
The marks shown on the table below are indicated on the disc's label, package or jacket.

DVD discs or packages include the marks shown below. These marks indicate the type of video or audio signals recorded on the disc and the functions that can be used.

PLAYABLE FORMATS The unit is able to play most audio/video files such as: PICTURE: JPEG AUDIO: MP3, WMA VIDEO: DAT, VOB, MPEG2, MPEG4 (AVI), DivX.

After unpacking, first check the contents of your DVD player package, as listed below:

Two AC / DC Adapters Two Remote Controls Two Car Power Cables



AUD IO IN/ OUT COAXIA L OUT D C IN 12V DC OUT 12V 1A CAR USE ONLY
4 VIDEO IN / OUT Input or output video signals to a connected device by setting AV IN/ OUT mode button on the remote control. The included AV cable is connected here. 2 USB port Support USB 1.1 use.
1 EARPHONE jack For connecting a stereo earphone or an amplifier.
5 AUDIO IN / OUT / COAXIAL OUT Input or output audio signals to a connected device by setting AV IN/ OUT mode button on the remote control. Output coaxial audio signals to a connected device. The included AV cable or coaxial cable (not included) is connected here.
3 DC OUT jack (12V 1A) DC output for car use only.
6 DC IN 12V Connect the included AC/DC adapter or car power cable here.

Volume UP/ down button
Press + button to increase the volume.
Press - button to decrease the volume. In the menu state, press +/- buttons to move the cursor right/left.
Press to locate the previous track or chapter. Press to locate the next track or chapter.
In the menu state, press / buttons to move the cursor down/up.
Press it to open the disk cover.
PLAY / PAUSE button
Press it to play. When pressing during playback, pause mode is set. Press again to resume playback. In the menu state press PLAY/ PAUSE to accept a menu operation as OK.
Press it to stop playback.
Press for 3 seconds to turn the unit ON or OFF.
PREV/NEXT button · STOP button · Power ON/OFF button

The unit can stand with this device.


Do not press down upon the DVD player when using the support, or damage will result.



1 SETUP
Press this button to display setup screen when at stop status.
Move the cursor down.
Jump to next track. 15 NEXT( )
Press this button to switch the audio languages on the DVD.
Press this button to stop playback.
SUBTITLE 3 Press this button to switch the DVD's subtitle language.
Fast backward key.
4 MENU
Press this button to play or pause playback.
Press this button to display the DVD's menu screen. While playing VCD disk, press it to switch between menu on or off.
Fast forward key.
20 STEP/SLOW( )
It is the shortcut key for AV IN founction
During playing status, press it to switch to SLOW mode, while switch to STEP mode at pause status.
Move the cursor up. 6 ( )
Zoom the picture on screen.
22 RETURN
Press this button to display the disc's information.
Return back to menu screen. If menu setting is off when playing VCD, the key is invalid.
8 PROGRAM Program playing order of tracks.
Move the cursor left. 9 ( )
Press this button to display the DVD's title.
OK Confirm and enter the selected item
24 CLEAR Clear the numbers inputted before.
Move the cursor right. 11 ( )
For DVDs, use this button to play titles or chapters repeatedly. For CDs, use this button to play tracks or the entire disc repeatedly.
12 SEARCH Locate title/ chapter/ playtime to play.
26 A-B REPEAT Press this button during playback to set two points and play the section between them repeatedly.
Jump to previous track. 13 PREV( )
14 ( ) · ( · (

Vol - Press it to decrease the volume
Press this button to switch angle.
Vol + Press it to increase the volume
Press this button to switch between number & function. (Default: function)
32 NUMBER KEYS Input number.
29 MUTE Press this button to mute the player.

Do not drop or step on the remote control unit or subject it to shocks. Note that the remote control unit may not work if there are obstacles between
the remote sensor and itself. Do not expose the remote sensor to strong light. Doing so may make operation impossible. Use the remote control unit within the specified operating range.
Insert your finger nails into A and B on the diagram below, press A according to the direction, then pull out the battery holder.
Remove the old battery, then insert the new battery into the battery holder with the + side facing upwards.

To prevent leakage of fluid from the lithium battery, remove the battery when not using the remote control unit for long periods of time (one month or more). If the battery leaks fluid, carefully wipe it out of the
Fit the battery holder back to its place.
battery case, then change to a new lithium battery. Caution: The battery may present a risk of fire if mistreated. Do not recharge, disassemble, or heat it above 100 C. Replace battery with the same type. Dispose of used battery properly, keep away from children and do not dispose of in fire.


The headrest mount is designed to fit the wide variety of shapes and sizes of headrests in modern cars. The foam pad allows you to set the angle of the screen and will eliminate vibration when the car is moving.


Gently slide the Portable DVD player by aligning the backpanel groove with the headrest mount, until you hear the click sound. See diagram below.

The headrest is a primary safety device in a car. Always adjust the headrest for optimum safety of the seat occupant. Fit & adjust the headrest mount thereafter.
down


AUD IO IN/ OUT CO AXI AL OUT DC IN 12V DC OUT 12V 1A CAR USE ONLY
Use the supplied AV cable to connect between the DVD player and your TV set, as shown.

CONNECTING THE ADAPTER TO THE DC IN 12V SOCKET

A UD IO IN/ OUT C OAXI AL OUT DC IN 12V DC OUT 12V 1A CAR USE ONLY
Do not connect to 24V supply or damage will result.

AUD IO IN/ OUT COAXI AL OUT DC IN 12V DC OUT 12V 1A CAR USE ONLY
Connecting the earphones will result in the disconnection of the internal speaker of the DVD player.

CONNECTING TO A DOLBY DIGITAL/MPEG DECODER OR AN AMPLIFIER WITH BUILT-IN DECODER
With this player, you can enjoy powerful Dolby Digital or MPEG sound. Output the digital signals from the player's digital output to a decoder or amplifier with built-in decoder.

AUD IOI N/O UT COA XIA LO UT D C IN1 2V DC OUT 12V 1A CAR USE ONLY
Signal flow · Surround · speaker

CONNECTING TO A DOLBY DIGTAL AMPLIFIER THAT IS NOT DOLBY DIGITAL / MPEG COMPATIBLE
Output the digital signals from the player's digital output to a digital amplifier that is not Dolby/ MPEG compatible. For instructions of audio settings, refer to AUDIO OUT of AUDIO SETUP.

AUDIO IN/OUT COAXIAL OUT D CIN 12V DC OUT 12V 1A CAR USE ONLY
Carefully check the player s digital output settings before connecting the player to an amplifier equipped with a digital audio input jack which is not Dolby Digital / MPEG compatible.
Do not play DVDs when the audio settings are not correct. Or it may cause strong noise and damage your speakers.
Signal flow


AUDI OI N/OUT C OAXIAL OUT D C IN12V DC OUT 12V 1A CAR USE ONLY
To audio input jacks
Left side · Active speaker systems


Connect the two players with AVP cable as described below: 1. Disconnect any 12V DC supply from both master & slave DVD players. 2. Connect the AVP cable into the master unit by inserting the DC OUT section of the cable to the DC OUT socket of the master unit. 3. Plug the DC IN section of the cable to the DC IN socket of the slave unit. 4. Connect the white Audio plug of the AVP cable to the audio IN/ OUT socket on both DVD players. 5. Connect the yellow video plug of the AVP cable to the video IN/ OUT socket on both DVD players.

There,s no actual difference between master unit and slave DVD players. Either of them can be appointed as master unit, then the other one acts as slave unit accordingly.
WHEN SHARING THE SAME MOVIE: IN CAR 1. Connect the two players with AVP cable first, and then plug the car power cable to DC IN socket of the master unit. 2. Turn on the two players. 3. Switch the SLAVE unit to AV IN status to stop normal playback and let it act as a monitor. Press the MODE button on the remote control to select AV IN function.



1. There,s no actual difference between master unit and slave unit. Any of them can be appointed as master unit, then the other one acts as slave unit accordingly. 2. One AC/DC adapter cannot supply enough power for two DVD players simultaneously. For home using, two adapters are provided. Each adapter can only service one DVD player. Simply Connect each adapter to the DC IN socket upon the two DVD player. Video & Audio jacks of both DVD players should be connected with the AVP cable, but no need to connect the jack. 3. For car using, the car power cable can be used for two DVD players to enjoy movie-share or two different movies simultaneously.
Master Slave · Master Slave

1.When sharing the same movie, i.e. one DVD player acts as a monitor, the two DVD players can choose the same IR channel option simultaneously. 2.When enjoying two different movies, the IR channels of the two DVD players must be adjusted to channel A and channel B respectively. Or interference will occur. See diagram below. 3.The relevant IR headphones should be switched to the corresponding channels in compliance with the IR channel options of DVD players.

Cordless IR headphones are available from your NEXTBASE distributor.

FM TRANSMITTER IR HEADPHONE CHANNEL A CHANNEL B OFF
System A System B DVD set to channel A
DVD set to channel B


Connect the AC/DC adapter to socket, or connect the cigarette plug to the outlet on your vehicle.
Connect the DC output plug of the cable to the DC input jack on the main DVD player.
Hold on the Power button for 3 secs to turn on the unit .
The included AC/DC adapter is compatible with voltage from 100 V
to 240 V, you can use it on trips overseas.
plug (Available in stores) suited for the region in which you are travailing.
1.When the power is on, press and hold on the Power ON / OFF button for 3 Secs to turn off the player. 2.Unplug the power cord from the power outlet, or disconnect the cigarette power cable. 3.Disconnect the DC plug from the player's DC input jack.
Power ON/OFF


Place in a disc and press down the disc with your fingers near the center hole.
A click is heard.
Set the disc securely. Failure to set it securely could result in damage. Do not use cracked or warped discs. Doing so could result in damage. Place single-sided DVDs or CDs in with the label (Printed) side facing upwards. For double-sided DVDs, check each side carefully, then place the disc in securely (Until a click is heard). For CDs or one-sided DVDs, you do not have to worry about touching the label (Printed) side of the disc with your fingers. Since two-sided DVDs have signals recorded on both sides, so be careful not to scratch them when removing them from the player.

OPEN button



it stopped by pressing the key. 4. To clear stopping mark, press again at
stop status. The player will not play from the stopping place when pressing next
time.

the remote control during playback. 2. Press again to resume normal

NOTE:
During fast or slow motion playback, the sound is muted expect playing CD & MP3 disc. To resume normal playback press .
A-B/REPEAT PLAYBACK




You can select a preferred subtitle from those included on the DVD video disc by pressing SUBTITLE button on the remote control during playback.
Press the ANGLE button on the remote control while playing a scene recorded with multiple angles. If your DVD disc is not recorded with multiple angles, pressing ANGLE button will not effect at all.

The program playback function can automatically play titles, chapters, or tracks in accordance with the programmed order.


When the DVD video player is turned off or the discs are removed, the programmed items will be removed.
Referring to the disc, some may not have this function.
Selecting an inexistent title or chapter, program playback will be canceled automatically.


Use to move the cursor to a folder, a file, MP3 ICON or JPEG ICON. In order to play MP3 files, move the cursor to MP3 ICON and press OK button. In order to play JPEG files, move the cursor to JPEG ICON and press OK button. Choose the desired file and press OK to play. Press A-B button to get A-B REPEAT function. Press REPEAT button to switch repeat mode(REP1,REP DIR, REP ALL, REP OFF). REP1 means repeating the track; REP DIR means repeating the folder; REP ALL means repeating the whole disc.
's

Your player is an Official DivX Certified product that plays DivX.5, DivX.4, DivX.3 and DivX.VOD video content, in compliance with DivX Certified technical requirements.
To guarantee playback of DivX files the audio must be MP3 format. DivX Certified devices can play any interleaved MP3 audio at any bitrate, both CBR and VBR. The audio must be sampled at standard frequencies, such as 32 kHz, 44.1 kHz, and 48 kHz, and must conform to the AVI file specification. Apart from MP3, the audio formats recognised by your player are MPEG layer 1 / 2 , AC3, PCM. Formats such as AAC and Ogg Vorbis are not supported by this player.
When there are music, images and DivX files contained on one disc, press several times the button to access the Play type at the bottom of the screes, then use the or button to select the DivX icon and press OK to confirm.
AVI
To go back to the folder list, press .
"Playing " & "playing DivX files" for the
MP3 format disc and JPEG CD


TV SYSTEM TV TYPE SCREEN FORMAT TV SCREEN PASSWORD RATING DEFAULT EXIT SETUP


The pressing of the following buttons will turn off the setup menu, and the choices that have been changed will be saved at the same time: Subtitle, Title, Return, Stop, Play / Pause, Step, Next. Prev, Zoom, Program, Repeat, Angle, Mute.

The system setup options are illustrated below:
If you want to connect the player to a TV, please choose a correct TV system first.
AUTO: Choose this setting if your DVD player is connected to a multi-system TV. NTSC: Choose this setting if your DVD player is connected to a NTSC TV. PAL: Choose this setting if your DVD player is connected to a PAL TV. The default setting is . AUTO
TV SYSTEM TV TYPE SCREEN FORMAT TV SCREEN PASSWORD RATING DEFAULT EXIT SETUP
Setting with incorrect TV system will result in black and white picture on your TV screen.

16:9 (Wide Screen): Choose this setting if your DVD player is connected to a wide screen TV. If you choose this setting and you don’t have a wide screen TV, the images on the screen may appear distorted due to vertical compression.
4:3 LB (Letter Box): Choose this setting if your DVD player is connected to a normal ratio TV. You’ll see the movies in their original aspect ratio (height -to width ratio). You’ll see the entire frame of the movie .The movie might appear with black bars at the top and bottom of the screen.
4:3 PS ( Pan& Scan): Choose this setting if your DVD player is connected to a normal ratio TV. You can fill the movie to the entire screen of your TV. This might mean that parts of the picture (the left and right edges) won’t be seen.

SCREEN FORMAT TV SCREEN PASSWORD RATING DEFAULT EXIT SETUP
The image display ratio is related to the recorded disc format. Some discs can not be displayed in the aspect ratio preferred. If you play a disc recorded in 4:3 format on a wide screen TV, black bars will appear on the left and right sides of the screen. You must adjust the screen setting depending on the type of the TV.

16:9: Choose this setting to change TFT MODE to 16:9. 4:3: Choose this setting to change TFT MODE to 4:3.
The default setting is 16:9.

NORMAL: Choose this setting to have normal display.
ROTATE 180 C: Choose this setting to have upside down display. The default setting is NORMAL.


If you forget your assigned password, you can use 0000 to unlock the rating again.

The rating feature works with DVD discs that have been assigned a rating. This helps you to control the types of DVDs that the player can be watched.
There are eight limited rating options: KID SAFE, G, PG13, PG-R, R, NC-17, ADULT The default setting is ADULT.

TV SYSTEM TV TYPE SCREEN FORMAT TV SCREEN PASSWORD
1 KID SAFE 2 G 3 PG 4 PG13 5 PG - R 6 R 7 NC - 17 8 ADULT
If the password option is locked, you cannot change rating.

Choose this option to resume factory settings.
TV SYSTEM TV TYPE SCREEN FORMAT TV SCREEN PASSWORD RATING

The language setup options are illustrated below:
Highlight the OSD LANGUAGE option, and press the arrow buttons to choose the OSD language you prefer. Press OK to confirm, and it will display OSD in that language. There are 5 optional OSD languages: English, German, Spanish, French and Italian.

Highlight the AUDIO LANG. option, and press the Arrow buttons to choose the audio language you prefer. Press to confirm. If the disc you are playing has that language available, it will output audio in that language. There are 8 optional audio languages: Chinese, English, Japanese, French, Spanish, Portuguese, and .

German Italian

SUBTITLE LANG.
Highlight the SUBTITLE LANG option, and press the arrow buttons to choose the subtitle language you prefer. Press OK to confirm. If the disc you are playing has that language available, it will display subtitles in that language. There are 7 optional subtitle languages: Chinese, English, Japanese, French, Spanish, German and Italian. Choose off to remove all subtitles from being displayed.

MENU LANG.
Highlight the MENU LANG option, and press the arrow buttons to choose the menu language you prefer. Press OK to confirm. If the disc you are playing has that language available, it will display menu in that language. There are 8 optional menu languages: Chinese, English, Japanese, French, Spanish, Portuguese, German and Italian.

If your preferred language isn’t available, the disc’s default language will be played. The default language of your DVD player is English.

Highlight the AUDIO OUT option, and press the arrow buttons to choose the audio output mode you prefer. Press OK to confirm: There are 3 optional audio output modes: SPDIF/OFF, SPDIF/RAW and SPDIF/PCM.
SPDIF / OFF: Choose this setting to output analog signal, and there will be no digital signal output from an coaxial output jack. SPDIF / RAW: Choose this setting if your DVD player is connected to a power amplifier with a coaxial cable. When playing a disc recorded with Dolby Digital and MPEG audio formats, the corresponding digital signals will be outputted from the coaxial Output jack. SPDIF / PCM: Choose this setting if your DVD player is connected to a 2-channel digital stereo amplifier. When playing a disc recorded with Dolby Digital and MPEG audio formats, audio signals will be modulated into a 2-channel PCM signal, and it will be outputted from the coaxial Output jack .

Highlight the IR HEADPHONE item and use the arrow buttons to choose the following options: CHANNEL A, CHANNEL B and OFF. Press OK to confirm. The selected IR option on the DVD player should be conformed to the adjustment of the receiving IR earphone. Or no sound can be heard. The default setting is OFF.

Compatible IR cordless headphones are available from your NEXTBASE distributor.



FM TRANSMITTER (Optional) · ;

The video setup options are illustrated below:
Use the UP and DOWN buttons to move the scroll and adjust the brightness.

Use the UP and DOWN buttons to move the scroll and adjust the contrast.


Use the UP and DOWN buttons to move the scroll and adjust the hue.

Use the UP and DOWN buttons to move the scroll and adjust the saturation.


The digital setup options are illustrated below:
Here are two sound output effect modes: NORMAL and SURROUND. You can choose SURROUND to enhance the output sound effect.

Choose this setting to adjust the line out compressing ratio and get different effects. If adjusting to FULL, the audio signal peak value will be compressed to be minimum; while adjusting to OFF, to be maximum.


DivX(R) VOD (VIDEO ON DEMAND)
DivX VOD files are downloaded after paying a rental from certain commercial websites. Prior to downloading a VOD you need to input the registration number of your DVD player on the purchase form on the site. Write down the VOD 8-character registration number so that you can fill in the form on the website you purchase your DivX VOD files from.
Note: If you cannot play a DivX VOD file recorded on a CD-R disc after downloading it, the rental period allocated during purchasing from the website may have expired. It is also possible that the recorded file is not compatible with your player because of different versions or incorrect download parameters. The parameters used when copying to CD-R may be another reason for this. Since it is not possible here to supply all the information, parameters and advice relating to the use of DivX VOD files, we recommend that you visit speciallist websites such as www.divx.com/vod
SOUND EFFECT DYNAMIC RANGE
EXIT SETUP
-DIVX [R] VIDEO ON DEMAND-
Y OUR REGISTRATION CODE IS:J JZB4GG6
TO LEA RN M ORE VISIT WWW.DIVX .COM/VOD
[DONE]
The registration code will be changed each time you use it to download the DivX files. You have to use new code to carry out downloading operation next time.
DivX(R) VOD


CHA L 2.3MHZ R 2.8MHZ CHB L 3.2MHZ R 3.8MHZ


Remember to insert back the rubber cover of the unit to BATTERY CONNECTOR after using the battery pack.
Supply power to the player. Do not short-circuit the terminals.
Connect the output plug of AC/DC adapter to the battery pack.
3 Battery indicator LED
When the battery is discharging, LED is off. When recharging the battery, LED is red. When the LED turns from red to off, it means finishing recharging.
1. The battery pack can be used for about 300 cycles of recharging and operations, though this is variable depending on the operating conditions. 2. Charge the battery pack fully before using it for the first time. Place the battery pack and AC/DC adapter on a flat surface for recharging. Do not short-circuit the terminals of the battery pack and AC/DC adapter. If the battery pack is fully recharged, the player can play DVD,s continuously for about 2 hours. 3. The battery charger(AC/DC adapter) is compatible with supply voltage between 100V and 240 V AC and can be used universally. When you want to use it on an overseas travel, be sure to prepare a power plug adapter matching the local power outlet. 4. The battery will be charged if connected to the DVD player and the DVD player is supplied with 12V DC. 5. Warning: Batteries (battery pack or installed) shall not be exposed to excessive heat such as sunshine fire or the like.
4 Slide fitting mount 5 battery stand
1 Attach the battery pack to the rear of the DVD player. 2 Slide the battery from the bottom, in an upward direction, to engage the slide fitting mount, Ensure the battery is pushed to the top of the slide to engage the connection. 3 Now the player will operate from the battery supply.
Battery Bottom

NO PICTURE
Is screen damaged? “ See smashed Screen Identification” section. Is power applied and power light on? Is disc cover ( screen ) closed correctly?
Is the volume turned down? Are headphones plugged in? Is the wrong audio track selected from the DVD?
Disc cover ( LCD screen ) is not firmly shut, close firmly.
Check that the disc is loaded correctly. Check disc for dirt / scratches, change the disc. Check disc is a good quality MPEG2 or MPEG4 standard. Check the lens. See separate section for procedure. Wrong region message - choose a different disc.
Approach player more closely or remove obstructions. Replace battery for new. Type Cr2025
MPEG4 is an open format, use only officially recorded quality media. No correct format files found (Mp3 JPG etc ) on the USB stick.
Reset the movie. Record movies using only official DivX software.
No power from car power cable. Check the fuse in the cable and check for cable damage check the player works on the mains adaptor. No power from mains adaptor check the cable for damage. Check the player works on the car power cable.
The LCD screen contains 336,960 pixels, pixels can fail during normal product life. 1 pixel = 0.0003% failure rate. One pixel failure per year of operation is considered normal and not a cause for concern.

DVD + RW format disks may not read correctly on this DVD player as the DVD +RW format is not a fully recognized format with the DVD forum. There are significant variations in the recording / media. Use DVD-RW or DVD +/- R media in preference.
Adjust the straps and tension them to fit correctly. Angle the mount towards the rear seat occupants.
Tighten the straps to prevent slippage.
Poor playback may be caused by dirt on the laser lens, which could come from even a fingerprint... The first approach is to expose the DVD mechanism and clean the lens. Use a clean, dry cotton bud (add pure alcohol sparing if available) and wipe across the lens VERY gently. The lens is held is sprung suspension so be very gentle and careful.


Wipe in a circular motion to take the dirt away from the lens.

A Liquid Crystal Display (LCD) screen is a multilayer complex component.
Under the tough outer plastic layer, the glass sandwich beneath holds the LCD crystals in place, which are themselves suspended in fluid. In the unfortunate event of an accident, particularly a sharp localized impact, the glass will break. The tough plastic outer sheet on the surface of the glass keeps all the glass intact underneath, preventing shards from falling out. This is a specific safety feature, particularly implemented for the younger user and also for in-car use. The broken glass normally shows signs of the impact mark and also cracks radiating away. The resultant fluid leakage renders the panel inoperable.
Symptoms are often a dark round mark, a white screen without picture and maybe some multicolored lines. Depending on the individual break, an element of the TV picture may remain for a while, but not for long, as the fluid leaks away. Some inky black staining may also appear upon the crack lines, as the fluid escapes.
Unfortunately a break of this nature is not covered under the manufactures warranty, as it is accidental damage to the product, rather than an original defect from manufacture. Please see below for some sample images of broken LCD panels for reference.


Have the unit serviced by a qualified service technician if:
The unit has been exposed to rain or water. The unit does not seem to operate normally. The unit exhibits a marked change in performance.


Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.