EN
Lorus logo
Official user manual

Lorus Z014

2 pages·6.1 MB·Watch·PDF·ENDEFRITNLJA
Lorus Z014
Table of Contents 61 sections NREZ014 8-2010 · CAL. Z014 (R23 SERIES) · FORMAT · S1 S2 OR S3 PRESS · … ShowHide
Page 1 of the Lorus Z014 user manual — NORMAL TIME
Page 1 · click to enlarge
Page 1

NREZ014 8-2010

CAL. Z014 (R23 SERIES)

  • HOW TO SWITCH 12-HOUR/24-HOUR
  • CHARACTERISTICS

FORMAT

1. Analogue & digital time displays: Hour, Minute, Second, Month, Date and day of the week. 2. Time Indication: 12-hour display format with PM indicator and 24-hour display format are available. 3. Daily alarm: The alarm can be set to sound at the designated time on a 24-hour basis. 4. Chime: The chime can be set to sound every hour on the hour with a single beep. 5. Stopwatch: The stopwatch can measure up to 23 hours 59 minutes and 59 seconds in 1/100-second increments. Lap time measure- ment is available. 6. 100 M Water Resistant 7. Illuminating light: The built-in electro- luminescent (EL) backlight illuminates the display for easy viewing in darkness.

S1 S2 OR S3 PRESS

PRESS AND HOLD

AFTER NOON

S1

S2 12 HOUR S3

24 HOUR

1. Press S1 or S2 button and hold it. Then press S3 button to switch the display. * The time display format in either 12-hour indication or in 24-hour indication can be selected alternately. * Under the 12-hour indication format, "PM" mark appears in the afternoon, but no AM mark appears in the morning. Under the 24-hour indication format, no mark appears on the display.
  • DISPLAY AND BUTTON OPERATION

DAY OF WEEK

SECONDS

S4

  • HOW TO DISPLAY MONTH/DATE

S1

1. From NORMAL TIME display, press S1 button and hold it to show the MONTH/DATE display. 2. Press S2 button to switch to the DATE/MONTH display. 3. Press S2 button again to switch back to the MONTH/DATE display. * The display format in either DATE/MONTH indication or in MONTH/DATE indication can be selected alternately by pressing S2 button.

ANIMATION DOTS

AFTERNOON

CROWN

S2 S3

S1

HOURS

MINUTES

ALARM SIGNAL

CHIME SIGNAL

S1

PRESS AND HOLD

* Press S2 button and hold to show the ALARM TIME. Release S2 button to return to the NOR- MAL TIME display. * Press S1 button and hold to show the MONTH/ DATE or DATE/MONTH. Release S2 button to re- turn to the NORMAL TIME display. * Press S3 button at any time to return to the NORMAL TIME display.

S2

PRESS

NORMAL TIME

MONTH/DATE

S2

S2

PRESS

  • SETTING THE TIME (ANALOGUE)

DATE/MONTH

CROWN

  • HOW TO SET ALARM TIME

S1

PRESS AND HOLD

S3

S2

1. Pull the crown out one step, the second hand will stop. 2. Set the correct time by turning the crown. 3. Push the crown back to the original position. The watch will start running again.

NORMAL TIME S3

2 SECONDS LATER

PRESS

S3

PRESS

* The analogue indication and digital display of the time setting can be adjusted separately.

S1

  • HOW TO SET NORMAL TIME

1. From NORMAL TIME display, press and hold S3 button for 2 seconds to show the ALARM TIME display. The hour digits start flashing. * The display is changed automatically to the ALARM TIME after 2 seconds. 2. Press S3 button again to move on to SECONDS setting. The second digits start flashing. 3. Press S2 button to set SECONDS setting. 4. Press S1 button to move on to MINUTES setting. * Selection of the digits to be adjusted (flashing) is made in the order below by pressing S1 but- ton and then pressing S2 button to be set. 5. After all the adjustment are completed, press S3 button to return to the NORMAL TIME display.

ALARM MODE

MINUTES SETTING S2

PRESS

HOURS SETTING S2

PRESS

1. From NORMAL TIME display, press and hold S3 button for 2 seconds to show the ALARM TIME display. The hour digits start flashing. * The display is changed automatically to the ALARM TIME after 2 seconds. 2. Press S2 button to set HOURS setting. 3. Press S1 button to move on to MINUTES setting. 4. Press S2 button to set MINUTES setting. 5. After all the setting are completed, press S3 button to return to the NORMAL TIME display.

S1

PRESS AND HOLD

Engagement/Disengagement of ALARM & CHIME * Press S2 button and hold it, and then press S1 button, the ALARM and CHIME can be en- gaged or disengaged in the order below. * The ALARM signal and/or CHIME signal appear or disappear on the display accordingly.

S3

S3

S2

NORMAL TIME

ALARM

PRESS

PRESS

NORMAL TIME

S3

S3

S1

PRESS AND HOLD

ALARM

S2

S2

ALARM SIGNAL

ALARM &

DAY OF WEEK SETTING S2

PRESS

SECONDS SETTING

PRESS

CHIME ON CHIME SIGNAL

S2

PRESS

PRESS

PRESS

S1

S1

S1 CHIME ON ALARM ON

CHIME OFF

PRESS AND HOLD

S2

PRESS

DATE SETTING S2

PRESS

MINUTES SETTING

S2

CHIME OFF

PRESS

CHIME ON

S1

PRESS AND HOLD

CHIME ON

PRESS

S2 PRESS

S1

PRESS

S1

S1

ALARM OFF PRESS AND HOLD

PRESS

S2

PRESS

MONTH SETTING S2

HOURS SETTING S2

ALARM & CHIME

OFF

Light · Start/Stop · Set Mode

Page 2 of the Lorus Z014 user manual — HOW TO RECALL THE LAP TIME DATA
Page 2 · click to enlarge
Page 2
  • HOW TO USE STOPWATCH
  • HOW TO USE EL BACKLIGHT

* From NORMAL TIME display, press S3 button to go to the STOPWATCH mode.

* In NORMAL TIME display, press S4 button to illuminate the display.

STOPWATCH MODE

PRESS

S4

S1

SECONDS

S3

S2

HOUR/MINUTES

1. Press S1 to start and stop the STOPWATCH. 2. Press S2 button to reset the STOPWATCH to "0:00: 00."

S1

S1 S2

  • BATTERY CHANGE

PRESS

1. The miniature battery SEIKO CR2016, Maxell CR2016 or SONY CR2016, which powers your watch, should last approximately 2 years. However, because it is inserted at the factory, the actual life of the battery once in your possession may be less than 2 years. 2. Be sure to replace the battery to prevent any possible malfunction as soon as it runs down. 3. To replace the battery we recommend taking the watch to a local watch repair shop.

S3

NORMAL TIME

STOPWATCH

START

PRESS

S1

RETURN

RESET

PRESS

PRESS

S3

S2

  • CARE OF YOUR LORUS WATCH

STOP

T h i s w a t c h c o n t a i n s p r e c i s e e l e c t r o n i c components. Never attempt to open the case or remove the back cover.

PRESS

S1

  • BATTERY

CAUTION

Do not expose the old battery to fire or recharge it. Keep it at a place be- yond the reach of children. If a child swallows it, consult a doctor immedi- ately.

S1 S2 S2 S2 S1

  • WATER RESISTANT
Condition of use Indication on the dial/ case backAccidental contact Swimmi with water, and taki such as a show splashes and rainng Skin ng diving erScuba diving No IndicationNO NONONO WATER RESISTANTYES NONONO WATER RESISTANT (50M/5 BAR)YES YESNONO WATER RESISTANT (100M/10 BAR ( or aboveYES YESYESNO

Start Lap 1 Reset Stop

PRESS

S3

NORMAL TIME

PRESS RETURN

STOPWATCH

S3

RESET

START PRESS

  • * If your watch is 200 M/20 BAR, 100 M/10 BAR or 50 M/5 BAR water resistant, it is so indicated on the dial/case back.
  • Do not operate the buttons when the watch is wet.
  • If the watch is exposed to salt water, rinse it in fresh water and then wipe it thoroughly dry.
  • Should you find any water or condensation inside the watch, immediately have it checked. Water can corrode electric parts inside the case.

PRESS

S2

S1

  • Caution: Leather straps are not water resistant except so indicated, even if the watch head is water resistant.
  • ALLERGIC REACTION Because the case and band touch the skin directly, it is important to clean them regularly. If not, shirt sleeves may be stained and those with delicate skin may develop a rash. Please wear the watch with some play to avoid any possible allergic reaction. If you develop a rash on your wrist, stop wearing and consult a physician.
  • MAGNETISM Your watch will be adversely affected by strong magnetism. Keep it away from close contact with magnetic objects.
  • SHOCKS AND VIBRATIONS Your watch may be worn for normal sports activities, but be careful not to drop it or hit it on hard surfaces.
  • TEMPERATURE Your watch is preadjusted so that constant accuracy may be insured at normal temperature.
  • CLEANING Use only a soft cloth and clean water for cleaning your watch. Never use chemicals, as the waterproof gasket will corrode.

PRESS

RECALL LAP MEMORY

S2

PRESS

LAP

S2

STOP

PRESS

S1

LAP

* While the stopwatch is measuring, press S2 button to take lap times. * Measurement and release of lap times can be repeated when S2 button is pressed.

HOW TO RECALL THE LAP TIME DATA

Lap time data obtained in the STOPWATCH mode can be recalled after measurement.

After stopping the stopwatch, press S2 button to view the recorded lap times.

  • SERVICE When your LORUS watch requires repair or servicing, please see the enclosed WARRANTY/GUARANTEE.

The lap times will be displayed one after an- other with each press of the button.

* Press S3 button to return to the NORMAL TIME display.

Show 8 more labels / short text on this page
Start/Stop · Mode · Reset/Lap · Standard Measurement · Start Stop Reset · Lap Time Measurement · Lap 2 · Printed in China

Ask about the Lorus Z014

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lorus Z014

Be the first to ask — other owners or our team will answer.

Original document

Lorus Z014 manual PDF

2 pages·6.1 MB·Watch·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…