
Time/calendar display Stopwatch display
-
-
-
M
-
Press button “A” for 2 sec.
INSTRUCTION MANUAL CAL. W136 (RE4 SERIES) CAL. W190 (RB7 SERIES) CAL. Y736 (RB9 SERIES)
A
1. Time/calendar display: Hour, minute, seconds, date, day of the week and month. 2. Automatic calendar adjustment: Cal- endar adjusts automatically for odd and even months except February of leap years. 3. Time indication: Changeover between 12-hour and 24-hour indications is pos- sible. 4. Stopwatch: 24-hour stopwatch with 1⁄100- second readout up to 40 minutes and with 1-second readout after the first 40 min- utes. Split time measurement is avail- able. 5. A l a r m : The alarm rings at the desig- nated hour and minute with “beep, beep” for 30 seconds. 6. Hourly time signal: Can be set to ring every hour on the hour with a single “beep”. 7. Illuminating light (except Cal. W140): The light evenly illuminates the display in the dark.
Engagement and disengagement of the alarm and the time signal. Button C while keeping button B pressed:
Changeover of the calendar (month and date) display. Buttons B & C:
Alarm test in the time/calendar display.
I HOW TO SET THE DUAL CALEN-
DAR DISPLAY 1 Press button “B” to show the calendar (month, date, and day) display. The calendar dis- play is shown while button “B” is kept pressed. 2 The month and the date change places with each other with each press of button “C” while keeping button “B” pressed.
[Cal. W136]
Month Day Date Day Date Month
B
M
B
* In the 12-hour indication, “A” (AM)/“P” (PM) mark is displayed. In the 24-hour indica- tion, there is no indication.
[Cal. W140]
Alarm mark Time signal mark
B
Split indicator Stop indicator
B: Start/Stop
[Cal. W190 / Y735 / Y736]
C: Split/
Split release/ Reset Minutes Seconds 1/100 second
A C
* The design of the day indication differs de- pending on the calibre.

1 Press button “A” to show the stopwatch display. (The stopwatch indicator starts flashing.) The stopwatch can measure up to 24 hours and is displayed in minutes, seconds, and 1/100 seconds up to 40 minutes, and in hours, minutes, and seconds after the first 40 minutes. (The 1/100 second indicator flashes during the first 40 minutes.) When the measurement is over 24 hours, the stopwatch will be reset to “0:00oo” and start counting again. 2 Reset the digits to “0:00oo” before using the stopwatch. When the split and the stopwatch indicators are flashing, press button “B” to check that the stop indicator starts flashing, and then press button “C” twice to reset the digits to zero. 3 When measuring a long period of time, return the stopwatch to the time/calendar display after the stopwatch starts to pre- vent any possible mistaken operation. * When button “B” or “C” is pressed in the stopwatch display, a single “beep” sounds to confirm the operation.
THE ALARM AND THE TIME SIGNAL
1 Press button “C” in the time/calendar dis- play to show the alarm display. The alarm display is shown while button “C” is kept pressed.
“A” (AM)
2 With each press of button “B” while keep- ing button “C” pressed, the engagement and disengagement of the alarm and the time signal are made as follows:
Alarm and time signal are disengaged.
Accumulated elapsed time measurement
Alarm is engaged. Time signal is disengaged.
Time signal is engaged. Alarm is disengaged.
Start Stop Restart Reset Stop
** Restart and stop can be repeated by pressing button “B”.
Alarm and time signal are engaged.
I HOW TO STOP THE ALARM
** Measurement and release of split time can be repeated by pressing button “C”.
The alarm rings at the designated time for 30 seconds and stops. However, the alarm can be stopped manually by pressing button “C” in any display.
Measurement between two competitors
B C B C C
The alarm can be tested with a beeping sound by pressing buttons “B” and “C” at the same time in the time/calendar display.
Reset Stop Finish time of 1st competitor
I HOW TO SET THE ALARM
B
B
A
A
1 Press button “A” to activate the time/calendar setting function. (The time/calendar setting indicator and the second digits start flashing.) 2 Selection of the digits to be adjusted (flash- ing) is made in the following order by pressing button “B”.
1 Press button “A” for 2 seconds to activate the alarm setting function. (The alarm set indicator starts flashing.) 2 Press button “B” to activate the “Hour” or “Minute” setting. The display changes in the following order with each press of but- ton “B”.
Seconds Minutes Month Hour
Hour setting Minute setting
3 One digit (flashing) is advanced with each press of button “C”. (The digits except seconds are advanced quickly by keeping button “C” pressed.) • Second setting Press button “C” in accordance with a time signal. The seconds are reset to “00” and start immediately. When the seconds count any number from “30” to “59” and button “C” is pressed, one minute is added and the seconds are immediately reset to “00”. 4 After all the adjustments are completed, press button “A” to return to the time/ calendar display.
M
3 One digit (flashing) is advanced with each press of button “C”. The digits are ad- vanced quickly by keeping button “C” pressed. 4 After all the adjustments are completed, press button “A” to return to the time/ calendar display. (The display returns directly to the time/ calendar display and not to the time/cal- endar setting.)
to check that the “A” (AM)/“P” (PM) mark is correctly set.

to check that the “A” (AM)/“P” (PM) mark is correctly set.
ViViDiGi is a new type of liquid crystal panel that makes possible various colors and high contrast.
AND THE 24-HOUR INDICATIONS
In the calendar or the alarm display, each press of button “A” changes over the time indication display from the 12-hour to the 24- hour and vice versa.
M
A
I BATTERY CHANGE The miniature battery which powers your watch should last as individually specified below. However, because it is inserted at the factory, the actual life of the battery once in your possession may be less than the specified period. Be sure to replace the battery to prevent any possible malfunction as soon as it runs down. To replace the battery, we recommend taking the watch to a local watch repair shop.
[Keeping button “B” pressed]
M
A
[Keeping button “C” pressed]
* When the “A” (AM)/“P” (PM) mark disap- pears, the calendar or the alarm display is shown in the 24-hour indication.
(dial, hands, buttons, case, bezel, strap, etc.)
✩If your watch is a LORUS LUMIBRITE watch,
it has following features.
LORUS LUMIBRITE watches absorb and store light energy from natural and artificial light sources and emit light in the dark. They are made of environmentally friendly material, and therefore, are harmless to human beings and the environment.
Do not expose the old battery to fire or recharge it. Keep it at a place beyond the reach of chil- dren. If a child swallows it, consult a doctor immediately.
(except Cal. W140)
When EL button is pressed and released in the time/calendar or stopwatch display, or in the alarm setting or time/calendar setting function, the electroluminescent light evenly illuminates the display for 4 seconds for easy viewing in the dark.
* If your watch is 200 M/20 BAR, 100 M/10 BAR or 50 M/5 BAR water resistant, it is so indicated on the dial/case back.

When your LORUS watch requires repair o r s e r v i c i n g , p l e a s e s e e t h e e n c l o s e d W A R R A N T Y / G U A R A N T E E .
Printed in China
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.