



DISCOVER & view YOUR CAMERA ON THE LOCAL NETWORK
SET UP YOUR CAMERA ON THE WIRELESS LOCAL NETWORK
STEP 2 LN Series Quick Setup Guide
Skills - Easy BASIC INSTALLATION GUIDE
Skills - Easy BASIC INSTALLATION GUIDE

Broadband Router and Computer are required for local and remote monitoring (not included).
CAMERA must be PLUGGED INTO YOUR ROUTER BEFORE STARTING THE WIRELESS SETUP. Steps 1 - 2 should to be completed.

Launching the DigiConsole Software
a

Connect the included network cable to the rear side of the LAN port on the bottom of the camera. Connect the other end of the network cable to the router, switch, or active wall port of your local network.
Before launching the program, please make sure your computer is connected to the same local network as the camera and has access to the Internet. The camera must be connected using the included Ethernet cable for initial installation. It is recommended to setup the camera when your computer is wired to the local network. If you are using the wireless connection on your computer, please make sure you are connected to your wireless router (check wireless name - SSID).



a Click Submit Wireless. Allow DigiViewer a few moments to apply your new connection settings. NOTE: Changing wireless settings may require devices to reconnect.
From DigiViewer, click Settings and then click Wireless. DigiViewer automatically scans for any wireless networks.
Place the base of the camera on a flat surface and screw on the stand.
Insert the included DigiConsole Software CD into your CD/DVD-ROM drive.
If a security pop-up window appears, click Unblock and Continue to allow DigiConsole to run.
If not already enabled, select Enabled from the Wireless Mode drop-down menu.

b


If the software runs automatically, please proceed to Step 2, section d.


Plug the power adaptor into the power port of the camera. Plug the other end to an electrical outlet. Note: Make sure the LED is lit on the front of the camera. If not, check that all cables are properly connected.
If the pop-up window appears, click Run Setup.exe and continue to Step 2, section c.
Attach the screw knob to the camera stand.
Click Find to discover Lorex cameras on your network.
This Network Camera is designed for easy installation. However, before you continue, please read the following:

From the list of available networks, select the wireless network for the device. If protection/encryption is enabled on the wireless router, you must enter the network password.

The Quick Start Guide refers to LNE1001, LNE3003 and LNZ4001 models and must be followed in sequence without skipping steps.
OPTION: If UPNP is enabled on your computer open the “Network” (“My Network Places” for Windows XP™ users) folder to view UPnP devices. (UPNP is disabled by default in Windows Vista™).
Attach the wireless antenna to the back of the camera.
After the initial setup, you can view the camera using Internet Explorer (with ActiveX), Mozilla Firefox and Safari

Add wired or wireless network cameras to expand the “Envelope of Protection” for your

If a security pop-up window appears, click Unblock and Continue. Click the warning on the browser bar and select Install ActiveX Control. Click Unblock or Continue in any proceeding security pop-ups.
2. Steps 1 - 2 should to be completed when your camera is connected wired before you can use the camera wirelessly. 3. When connecting the camera to a wireless network, consider the following: a. If your wireless router is not set up with wireless encryption, you can start the installation process immediately. b. If your wireless router is set up with the encryption, please make sure you know the encryption key. If you do not know the encryption key (encryption password), please refer to your router’s manual in order to reset the key. c. If your wireless router is set up with a different type of encryption please refer to your router’s manual in order to change encryption type to WEP - Open, WPA - Personal, WPAZ - Personal. d. The camera is compatible with Macintosh for viewing only. Recording on Macintosh is not supported. When using Macintosh auto discovery “Bonjour” advanced knowledge is required. Please refer to “Setting Up Using Macintosh” FAQ on LOREX web site www.lorextechnology.com
Screw the camera to the camera stand.



Enter admin in the username and admin in the password fields to access your camera. The browser will prompt you to install ActiveX.



For detailed setup information, please refer to the User’s Manual included inside the software/
Click the warning bar (it will turn from yellow to blue) and select Install ActiveX.
Tighten the screw knob to secure the camera.
work Wireless.
support CD . For additional information, please
Depending on your browser security settings, you can use the “remember me” check option and the next time you will view the same camera using this browser it will renumber user name and password till you restart your computer.
Click Install to start the installation. Click Unblock or Continue in any security pop-up. (This step is required only for first time set-up).
visit our website www.lorextechnology.com
Information in this document is subject to change without notice. As our products are subject to continuous improvement, Lorex Technology Inc. and our subsidiaries reserve the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE © 2010 LOREX. All rights reserved.

now set-up for local viewing
LN Series_QSG_EN_R2

LOREX EASY CONNECT INTERNET REMOTE MONITORING ADVANCED (AUTO PORT FORWARD WIZARD)
LOREX EASY CONNECT INTERNET REMOTE MONITORING ADVANCED
REMOTE VIEWING USING iPHONE ™ , iPOD TOUCH ™ & iPAD ™
LOREX EASY CONNECT INTERNET REMOTE MONITORING ADVANCED

OPTIONAL DDNS DDNS
STEP 4A
STEP 4B STEP 4B
on your pc
on your pc on your pc on your pc & IP CAMERA
Continued
Continued
Step 3: Update the Router Settings
Using Yoics
Complete New Account Information:





Your IP camera is designed to work with Yoics easy-connect remote access. Yoics remote viewing allows you to access your camera from a remote location without needing to configure your router.


Record the IP and MAC Addresses in the section below:

IP ADDRESS: . . .

(Required for DDNS registration)
9 An automated REGISTRATION CONFIRMATION EMAIL will be sent to your email. Print and Save this confirmation. You will need this information to access your System remotely.
Ports (by default): 80 (Web Port), 554 (Video Port (RTSP)
Auto Port Forward Wizard 2 The Lorex Auto Port Forwarding Wizard is a software that automates router port forwarding. You must have the following before you configure the software: 1. Your router’s model and version numbers 2. Your router’s user name and password 3. Your Lorex device’s IP address 4. Your Lorex device’s port numbers that require port forwarding
Manual Port Forward: 5 If you were unable to port-forward your router automatically using the wizard, you will need to do so manually. All routers are different. To port forward your router, please refer to your router’s user manual. An example of a port forwarding screen is shown for illustration purposes. Ports: 80 (Web Port), 554 (Video Port (RTSP)
Downloading the App:
Registering your Camera 3 1. A pop-up window opens and informs you that your camera has been detected. Click Continue in the registration screen to enable Yoics Easy Connect. 2. You can rename your camera (e.g. myoffice). Click Register Now. After the registration your IP camera will appear on the left side bar under My Stuff/Cameras


You must download the application from the Apple App Store. NOTE: You must create an App Store account before you can download content. A valid credit card is required to create an account, however the download of the above Apps is free of charge.


The Auto Port Forwarding Wizard automatically populates a list of current routers, and detects the number of connected routers. 1. Click the Next button after the software detects your router configuration.



6 Open your web browser (Internet Explorer by default) and enter http://www.lorexddns.net in the address bar.

For detailed setup information, please refer to the User Manual included inside the software CD.
Step 2: Enter your Router Settings

Connect to your IP Camera 4 1. Double click your IP Camera to view live camera images. Double click on the camera’s name to view the feed.



Enter the IP Camera’s user name (admin) and password (admin) to login to the device.

Congratulations! Now that you have a Yoics account set up you can log in to http://lorex.yoics.com to remotely view your cameras from anywhere in the world
using Internet Explorer web browser (Windows operating system only).

Congratulations! You have completed 4B successfully. Your camera is now set-up for remote viewing on any PC. You can now log into your Lorex account from anywhere in
the world with your DDNS URL address.
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.