


Direct USB recordings Record music from a CD player on your USB device.
Go to page 15
Genuine spatial sound reproduction in 5.1 channel mode of your TV, DVD player and digital devices.

WARNING: This product uses a Laser System. For correct use, read the user manual carefully and save for future use. If the device needs maintenance, please contact an approved service centre. Use of operation or adjustment or performance procedures other than those specified herein may lead to hazardous exposure to radiation. Avoid direct exposure to the laser beam, do not open the housing. Visible laser radiation when opened. DON'T LOOK IN THE BEAM.
WARNING: Do not block ventilation openings. Install according to the manufacturer's instructions. Slots and openings in the cabinet are there for ventilation purposes, to ensure reliable use of the product, and protect against overheating. The openings must never be blocked by placing the product on a bed, carpet, couch or similar. This product shall not be incorporated in which there is insufficient ventilation, such as a bookcase or rack, follow the manufacturer's instructions.
This symbol warns the user of the presence of important usage and maintenance instructions in the device manual.
RISK OF ELECTROCUTION. DO NOT OPEN.
European Representative:
Removal of your old device
Pull the plug and not the cable for release from the socket. Place the product so that it is easy to reach.
Protect the cable from physical or mechanical abuse, such as turning, securing, perforation, clamping between a door, or walking on it. Watch plugs, sockets, and the point where the cable goes off.
All these conditions can lead to electrocution or fire. Regularly examine the cable of your device and its appearance for signs of damage, wear, pull out the cable, and stop using it, and have the cable replaced by an exact replacement by approved service personnel if it appears to be damaged.
Do not connect too many devices to wall sockets. Overloaded wall sockets that are loose or damaged, extension cables, broken power lines, or damaged or cracked cable insulation are also dangerous.
That is a single circuit that only supplies power to the device, without additional sockets or plug boxes. Check the specification page in this manual.
It is recommended for most devices that they are connected to assigned circuit:
LG Electronics Service Europe B. V. Veluwezoom 15, 1327 AE Almere, The Netherlands (Tel: +31-036-547-8940)
This product is made according to the EMC DIRECTIVE 2004/1008/EC, and Low Voltage Directive 2006/95/EC.
1. If this crossed waste bin symbol is on the product, it means that the product is covered by European Directive 2002/96/EU. 2. All electrical and electronic products should be disposed of separately from household waste via collection points allocated by the government or municipality. 3. The correct removal of your old device prevents possible negative effects on the environment and human health. 4. For more information about the disposal of your old device, please contact your municipality, waste processing plant or shop where you bought the product.



b Attach the cables to the DVD receiver At each end point at the back of the DVD receiver, check for the cable with the matching colour. Open the end point by pressing the plastic tab. Insert the cable end into the stop point and release the tab.
a You've received six speaker cables. Each cable is provided at both ends of a band in a certain colour and connects one of the six speakers to the DVD receiver.
2 Attach the loudspeakers to speaker supports by turning the screw.
1 Pull the speaker cable through the hole in the loudspeaker.
Please note that children do not push their fingers or objects into the *speaker channel *Speaker Channel: A space in the speaker cabinet ( housing) for powerful low-tones display. Do not place the speaker cables in the hole in the speakers.
To attach the cables to the speakers, press the respective tabs to open the connection points at the foot of each speaker. Attach the cable in the opening and release the tab.
c Attach the cables to the loudspeakers Connect the other end of each cable to the right speaker according to the color coding:
Connect the red end of each cable to the connecting points with a + (Plus) and the black end at the connection points with an carbuncle (Min).
For you, on the left of the screen.
For you, right of the screen.
Upstairs screen, right in front of you.
Behind you and to your left
Behind you and to your right


b Attach the power cable to an electrical outlet.
a Connect the plugs to your TV (DVD player or other digital device) with cables.
Connect the TO TV input of the device to your TV using the SCART cable.
FM - Connect the FM antenna. The reception will be best if two separate ends of the antenna are placed in a straight line and horizontally.
Connect the VIDEO EXPLANATION (MONITOR) of the device to the corresponding input sockets on your TV using a Video cable.
The Audio contact points of the device are color-coded (red for right audio channel and white for left audio channel). If your TV has only one input for audio (mono), connect it to the left (white) audio input of the device.
Connect the COMPONENT VIDEO (PROGRESSIVE SCAN) OUTPUT of the device to the corresponding inputs of your TV using a YPbPr cable.

Connecting the device Connecting it . .
HDMI In connection
Connect the HDMI OUTPUT connector bus of the device to the HdMI INPUT plug bus of a TV compatible with HD MI, using an HDmi cable.
Connect the HDMI input of the device with an HD MI cable to your set-top box (or digital device) output. Set the external source to HDMI IN by pressing the INPUT. You cannot change the resolution in HDMI IN mode.
Connect the optical input of the device to the optical output of your TV (or a digital device).
You can also enjoy the sound of external sources with your device. Press INPUT again to select the desired input source. - AUX, AUX OPT, TV-AUDIO, PORTABLE, HDMI IN, USB, OSD IPOD, IPOD
[HDMI OFF]: Auto, 1080p, 10 80i, 720p and 480p (or 576p) [COMPONENT VIDEO OFF ]: 480p, or 576 p, and 480i (or 576i) [VIDEO OF F]: 480i, or 576l, [SCART]: 576i
You can change the resolution for component video and HDMI output. Use the resolution settings menu to select your desired resolution - Auto, 480i(576i), 480p(575p), 720p, 1080i, 1090p.

e
d
b
a
Remote control
MUTE: Press MUTE to turn off the sound of your device. You can turn off the sound of your device to answer the phone, for example.
d TVtConfigure HT SPK (5.1 channel view): Press TVtHT SPK to select the AUX OPT immediately.
SCAN(bb/BB): Move forward or back.
SKIP(. / >): Go to next or previous chapter/number.
c STOP (x): Stops playing or recording. PLAY (B): Start playing it. Mono/Stero(St.) PAUSE/STEP (X): Pause playback.
PRESET(v/V): Selects a radio program. TUN.(-/+): tuning in to the desired radio station. b / B / v / V (left/right/up/down): Used to navigate through onscreen screens. ENTER: Confirms menu selection. RETURN (O): Press this to get back in the menu.
b
INPUT: Change input source (AUX, AUX OPT, TV-AUDIO, PORTABLE, HDMI IN, USB, OSD IPOD, IPOD) SLEEP: Automatically disables the system at a time you choose. (Dimmer: This allows you to reduce the light intensity of the LED status lamp on the front panel by half if the system is switched on.) POWER: Turn the device on/off. FUNCTION: Selects the function (DVD/CD,FM) TITLE: If the current DVD has a title, the title menu will be displayed on the screen. Otherwise, the disk menu will be displayed. DISPLAY: Opens Display on screen MENU: Opens the menu of a DVD drive. SETUP: Opens or closes the Settings menu.
a
f RDS: Radio Data System. PTY: Displays the different screens of the RDS.
PROG./MEMO.: Opens or closes a program menu. CLEAR: Removes a number from the Program List.
e TV control buttons: Controls the TV. (LG TV only).
VOLUME (+/-): Adjusts the loudspeaker volume. EQ : You can choose from 6 (or 7) programmed sound impressions. VSM : Press VSM to set Dolby Pro Logic II or VIRTUAL sound. REPEAT: Repeat chapter, number, title or everything. SUBTITLE: During playback, press SUBTITLE repeatedly to select the desired subtitle language. 0-9 numeric keys: Selects numbered options in a menu.
You can control the sound level, source selection and on/off switch of LG TV performances. Press the POWER (TV) button and then press the PR a few times (+/.) button to turn the TV on or off.
Note that + (plus) and .g. (min) on the batteries match those on the remote control.

Power Enable/disable the device.
USB Port The USB port allows you to connect a storage medium to your DVD player.
Port THE PORT. In port means that you can have an audio device played via the surround sound speakers.
Volume Check the volume when using a function.
VSM Selects Dolby Pro Logic II or Virtual Sound.
Tuning (-/+) Skip / Search
Play/Pause, Function Hold this button for about 3 seconds, then press it repeatedly to select another function.
DVD/CD tray · Stop


Video Resolution - Use vV to select your desired resolution and press ENTER to confirm your choice. You can set the 1080p video resolution to enjoy full HD image quality (full upgrade to HD). The number in 480p (or 576p), 720p, 1080p and 1080i shows the number of lines. The .i .l and .p.l mean interlined and progressive scans respectively. [Auto] If your HDMI input is connected to the TV for providing screen information (EDID), then automatically selects the resolution that best fits with the associated TV (1080p, 1080i, 720p or 480p (or 576p)). (for HDMI connection only) [1080p] . (for HDMI connection only) [1080) . . Performs 1080 lines interlined video. (for HDMI connection only) [720p] . . (for HDMI connection only) [480p (or 576p)] . . Performs 480 (or 576) lines progressive video. [480i (or 576i) ] . . Executes 480i ( or 576) lines of interlined video.
TV Aspect . . Select the screen ratio based on the shape of your TV screen. [4:3]: Select this option if a standard 4:3 TV is connected. [16:9]: Choose this option if a 16:9 widescreen TV is connected. Screen Mode . If you have selected 4:3, please indicate how to watch widescreen programmes and movies on your TV. [Letterbox]: Here a wide screen is shown with black beams at the bottom and top of the screen. [Panscan]: The entire 4:3 screen is shown, with the image being cut. TV Select Output . Select an option according to the TV connection type. [YPbPr]: If your TV is connected to the COMPONENT/PROGRESSIVE SCAN plugbuses of this device. [RGB]: If your TV is connected with a SCART plug bus.
HD AV Sync - Sometimes digital TV has a delay between image and sound. If this occurs, you can compensate by setting a delay in the sound so that there is effective . . Use vV to browse up or down through the delay factors you can set between 0 and 300 m/sec. The delay depends on which digital TV channel you have selected. If you change the channel, it may be necessary to modify HD AV Sync.
DRC (Dynamic Range Control . . . Keeps the sound clear when lowering volume (Dolby Digital only). Set this effect to [ON]. Voxal. . Select [On] to mix karaoke channels with normal stereo view. This function is only suitable for DVDs with the possibility of multichannel karaoke.
5.1 Speaker Configuration - With this menu you set the amplifier for sound reproduction via 5.1 channels. [Speaker]: Select the speaker you want to customize. [Size]: Since the speaker settings are fixed, you cannot change them. [Volume]: Adjust the output volume of the selected speaker. (-5dB ~ 5dB) [Distance]: If you connect speakers to your DVD/CD receiver, setting the distance will ensure that the speaker knows how far the sound should travel before it reaches your set listening point. This means that the sound of each speaker reaches the listener at the same time. Press b/B to adjust the distance of each selected speaker. (You cannot adjust the front / Woofer speakers) [Test]: Press b/B to test the signals of each speaker. Adjust the volume to the volume of test signals stored in the system.

Bit Rate . You can set the quality of the recorded file.
DivX(R) Registration . . We will give you a DivX® VOD (Video On Demand) registration code that allows you to buy and rent video footage via the Divx® Vod service. For more information, please visit www.divx.com/vod Press ENTER if the icon [Select] is marked, and you can see the registration code of the device.
Region code . . Select a code for a geographical area as playback assessment level. This determines which regional standards are used to control DVDs in respect of underlocking. See Region codes on page 19.
Password . Set or change password for lock settings. [New]: Enter a new 4-digit password using the numerical keys and press ENTER. Please re-enter the password for verification. [Change]: Enter the new password twice after entering the current password.
Assessment . Select a rating level. The lower the level, the stricter the assessment. Select [Unlock] to disable the review.
To select the lock options, you need to enter a four-digit password. If you have not yet entered a password, the system will ask you to do so now. Enter a four-digit password and enter it again for verification. Press Clear if you make a mistake entering the number. You can reset your password if you forget. Press SETUP to display the installation menu. Enter .210499 . and press ENTER. The password has been erased now.
This system has a number of preset surround sound fields. Select the field that matches best the program you are looking at by repeatedly pressing EQ to browse through options: STANDARD, NATURE, AUTO EQ, POP, CLASSIC, ROCK, JAZZ
5.1Ch Source [VIRTUAL] mode: The multichannel sound changes the sound from 5.1 ch to a virtual sound in 10.1 ch so that it looks like you are listening to sound coming out of right, left and center speakers simultaneously.
2Ch Source [PL II MOVIE] mode: The movie mode is used in stereo television shows and all program scripts encoded in Dolby Surround. The result is improved sound field directionality that comes close to separate 5.1 channel noise. [PL II MUSIC] mode: The music mode can be used for any stereo recording. [PL II MATRIX] mode: Matrix mode is the same as Music mode, except that directional improvement logic is disabled. This can be used to strengthen monosignals by making them appear larger. Matrix mode can also be used in car systems, where fluctuations of bad FM stereo reception may cause disturbing sound from a logical decoder. The ultimate .audio mono solution . for poor FM stereo reception can simply be set up for audio. [ON STAGE] mode: The sound sounds like in a concert hall. [VIRTUAL] mode: Real-time 3-dimensional sound rendering technology with stereo sources, optimal for stereo speakers. Listeners can enjoy amazing virtual surround effects with their own multimedia players.
You can select Dolby Pro Logic II or Virtual sound. Press VSM to set the virtual sound or change sound mode again. [BYPASS] mode: Software with multichannel surround audio signals is played in the way it was recorded.
Set the sound mode
[AUTO EQ]: AUTO eq only works with MP3/WMA files containing this information. (ID3 Tag only works at far. 1). WMA file works with Normal EQ regardless of the Tag information.


1 ENG
D
Selected subtitles Selected angle/total number of angles
Current title (or track) Number/total number of files (or numbers) Current chapter number/total chapters Provide playtime Selected audio language or channel
MP3 ALL
Press REPEAT repeatedly to select a repeat part. The current title, chapter or track will be played repeatedly. To return to normal playback, press REPEAT repeatedly to select [Off].
Press PAUSE/STEP (X) repeatedly to play image-by-screen.
Press PAUSE/STEP (X) to pause the playback. Press PLAY (B) to continue playing.
Press SKIP (>) to go to the next chapter/track. Press SKIP (.) to return to the beginning of current chapter/track. Press SKIP (.) briefly twice to go back to the previous chapter/track.
Most DVDs nowadays have a menu that is loaded before the movie is played. You can browse these menus by using vV b B to highlight an option. Press ENTER to select.
Play a disk or file . . what else you can do
6 Stop playing a disc x STOP
5 Start playing a disc: B PLAY
4 Adjust the settings menu vVb B or select a file from the menu v V
2 Place a disc: (On device) -
1 Open Disc Tray: (On device: Z ) -
Play a disc or file
ALL
ALL
DVD
ALL

This device remembers the last scene of the last watched disk. The last scene remains in memory even if you delete the drive from the device or turn off the device (standby). If you load a disc that remembers the scene, the scene will be called automatically.
Search for the starting point or timecode entered. Press DISPLAY while playing and select the time-clock icon. Enter the required start time in hours, minutes, and seconds OK and on ENTER. If you enter the wrong number, press Clear to re-enter it.
Press MENU to show the disk menu if available.
Press TITLE to display the disc title menu, if available.
Press PLAY while a DVD is already playing to watch and listen to a D VD 1.5 times faster. B x1.5 is shown in the right corner of the screen. Press PLAY again to return to the normal playback speed.
While playing is paused, press SCAN (m or M) to slow it down forward or backwards. You can change the playback speed by pressing SCAN (m or M) repeatedly. Press PLAY (B) to continue playing at normal speed.
During playback, press SUBTITLE () repeatedly to select your desired subtitle language.
Press SCAN (m or M) to move forward quickly or rapidly while playing. You can change the playback speed by pressing SCAN (m or M) repeatedly. Press PLAY (B) to continue playing at normal speed.
DVD
DVD
DVD
DVD
ALL
WMA MP3 ACD DVD
If the subtitles are not shown correctly during playback, press SUBTITE for about 3 seconds and press SUBTitle to select another language code until the appropriate subtitle is displayed.
Change the character set for showing DivX® subtitles correctly
When playing a drive or USB Flash Drive with DivX, MP3/WMA and JPEG files, you can select which menu files to play by pressing TITLE.

You need to set up an appropriate system mode for your TV system. If NO DISC is shown in the window, hold PAUZE/STAP (X) for more than 5 seconds to select a system.
The screen saver is displayed if you leave the device in Stop mode for about five minutes.
When playing an MP3 file with file information, you can display the information by pressing DISPLAY repeatedly.
You can play the content in the order you want by setting the music sequence on the disk. The program will be deleted as soon as the drive is removed. Select the desired music and press PROG./MEMO. or select . . and press ENTER to add music to the program list. To add music to the disc, select . . and press ENTER. Select music from the program list and press ENTER to start playing programmed. To delete music from the program list, select the music you want to erase and press Clear or select the icon . . To remove all music from the program list, select . . and press ENTER.
WMA MP3 ACD View photo files
MP3
Press PAUSE/STEP (X) to pause a slideshow. Press PLAY (B) to continue the slideshow.
Pause a slide show.
Rotate the photo using vV b B while viewing it in full screen.
Press SKIP (. or >) to view the previous/next photo.
Use vV b B to mark the () icon and press ENTER to start the slideshow. You can change the speed of the slideshow using b B if it is marked with icon.
View photo files . . what else you can do
6 Return to the menu: x STOP
5 Display the selected file in full screen: ENTER
4 Select a photo file: v V
3 Close the disc tray: (On device: Z ) -
2 Place a disc: (On device) -
1 Open Disc Tray: (On device: Z ) -

Press PLAY (B) (MONO/ST) to play. This changes the tuner from stereo to mono and usually improves reception.
Hold PROG./MEMO. Two seconds. ERASE ALL (clear all) flashes to the screen of the DVD Receiver. Press PROG./MEMO. to clear all stored drives.
The program number can be selected when saving a radio station. If the player automatically shows a program number, press PRESET v/V to change this. Press PROG./MEMO. to save the chosen number.
Hold TUN.-/TUN.+ for more than a second. The tuner will automatically scan and stop as soon as a radio station is found.

5 To select a .save .drive, enter the Program Number: Up to 50 radio stations can be stored. PRESETv/V
4 A radio station . . A program number is displayed in the screen. PROG./MEMO.
CT (Time controlled by the station) This shows time and date as broadcasted by the drive.
RT (Radio text) A text message with special information from the station broadcasting is displayed. This text can roll over the screen.
PTY The type of the program (e.g. Jazz or News) will be shown on the screen.
PS (Program service name) The channel name is displayed on the screen.
The FM tuner comes with RDS (Radio Data System). This shows information about the radio station that is being listened to. By repeatedly browsing RDS through the different data types:
4 AUX-OPT CLOSING FUNCTION OR IMPORTATION
3 Listening to sound with 5.1ch speaker: -
2 Select AUX OPT: AUX OPT Directly Select TV t HT SPK
1 Close the OPTICAL access of the device to the optical output of your TV (or a digital device). -
Genuine spatial sound reproduction in 5.1 channel mode of your TV, DVD player and digital devices. If you even press TVtHT SPK in the disabled mode, the device will be switched on and automatically changed to AUX OPT mode.

5 Before disconnecting the portable USB device, change another function by pressing: FUNCTION OR INPUT
3 Select a file from the menu: v V
2 Select the USB function: INPUT
1 Connect the USB device to the device using a USB cable (not supplied): -
The advantage of connecting your portable USB player via the system's USB port is that the USB device can be controlled through the system.
Listen to music from your USB device • What else you can do

Record music from a CD player on your USB device. .what else you can do Recording Audio CD source to USB Record one song - If the USB recording is played while playing the CD, it will be recorded on the USb. Record all numbers - If the USB Rec. button is pressed while the CD has stopped, all songs will be recorded. List of programmes - USB starts recording after selecting the numbers by pressing PROG. button if you want to record the desired number.
1 Connect the USB device to the player using a USB cable (not supplied): - 2 Select a mode (DVD/CD) in which you want to record: FUNCTION 3 Start recording: z If you want to include the desired music file in Disk to USB. Select a file after starting recording: v V and z 4 Stop a recording: x STOP
Record music from a CD player on your USB device.
1 Connect the portable player by connecting the device to POORT. In front of the player. - 2 Enable the device: POWER 3 Select the TRUCK function: INPUT 4 Turn on the portable player and start playing. -
The player can be used to play the music of many kinds of portable players.

8 Before disconnecting the iPod, change another function by pressing: FUNCTION or IMPORT
6 Start playing files: B PLAY or ENTER
5 Select a file: v V
4 Select the menu: v V ENTER
3 Select iPod or OSD iPods feature: INPUT
2 Enable the device: POWER
1 Connect the iPod by connecting the device to the back of the player. -
iPod mode: You can control your iPod using the included remote control and controls on your ipod. The monitor's off. When you select iPod mode, the iPoD will not be charged. But you can enjoy better sound quality. OSD iPod mode: You can control your iPod via the OSD menu on the TV screen using the included remote control. The operation on your iPod cannot be used in OSD iPods mode. Select the OSD iPod mode if you want to charge the iPods while listening.
iPod Holder
Press REPEAT repeatedly to select a repeat part. The current title, chapter or number will be played repeatedly. To return to normal playback, press REPEAT repeatedly to select [Off]. iPod Message
Fast forward or fast backward Press SCAN (m or M) while playing and release this button at the desired point.
Press SKIP (>) to go to the next file. Press SKIP (.) to go back to the beginning of the current file. Press SKIP (.) briefly twice to go back in current file.
Pause playback Press PAUSE/STEP (X) to pause the playback. Press PLAY (B) to continue playing.
Listen to music from your iPod ♪ What else you can do
iPod mode OSD iPods mode
iPod mode OSD iPods mode
iPod mode OSD iPods mode
OSD iPod mode · OSD iPod mode

Zone Code Afghanistan AF Argentina AR Australia AU Austria AT Belgium BE Bhutan BT Bolivia BO Brazil BR Cambodia KH Canada CA Chile CL China CN Colombia CO Congo CG
Choose a region code from the list.
Language Code Aphasic 6565 African 6570 Albanian 8381 Amharic 6577 Arabic 6582 Armenian 7289 Assamees 6583 Aymara 6588 Azerbaijani 6590 Bashkir 6665 Basque 6985 Bengali; Bangladesh 6678 Bhutani 6890 Bihari 6672 Breton 6682 Bulgarian 6671 Burmese 7789 Belarusian 6669 Chinese 9072
Use this list to select the language you want for the following initial settings: Disk Audio, Disk Subtitles, Disc menu.
Zone Code Costa Rica CR Croatia HR Czech Republic CZ Denmark DK Ecuador EC Egypt EG El Salvador SV Ethiopia ET Fiji Islands FJ Finland FI France FR Germany DE UK GB Greece GR
Language Code Croatian 7282 Czech 6783 Danish 6865 Dutch 7876 English 6978 Esperanto 6979 Estonian 6984 Faroën 7079 Fiji 7074 Finnish 7073 French 7082 Fries 7089 Celtic 7176 Georgian 7565 German 6869 Greek 6976 Greenland 7576 Guarani 7178 Gujarati 7185
Zone Code Greenland GL Hong Kong HK Hungary HU India IN Indonesia ID Israel IL Italy IT Jamaica JM Japan JP Kenya KE Kuwait KW Libya LY Luxembourg LU Malaysia MY
Language Code Hausa 7265 Hebrew 7387 Hindi 7273 Hungarian 7285 Icelandic 7383 Indonesian 7378 Interlingua 7365 Irish 7165 Italian 7384 Javaans 7487 Kannada 7578 Kashmiri 7583 Kazakh Staans 7575 Kyrgyz 7589 Korean 7579 Kurdish 7585 Laothiaans 7679 Latin 7665 Latvian 7686
Zone Code Maladiven MV Mexico MX Monaco MC Mongolia MN Morocco MA Nepal NP The Netherlands NL Netherlands Antilles AN New Zealand NZ Nigeria NG Norway NO Oman OM Pakistan PK Panama PA
Language Code Lingalees 7678 Lithuanian 7684 Macedonian 7775 Malagasy 7771 Malaysia 7783 Malayalam 7776 Maori 7773 Marathi 7782 Moldovan 7779 Mongolian 7778 Nauru 7865 Nepalese 7869 Norwegian 7879 Oriya 7982 Panjabi 8065 Pashto, Pushto 8083 Persian, Iranian 7065 Polish 8076 Portuguese 8084
Zone Code Paraguay PY Philippines PH Poland PL Portugal PT Romania RO Russian Federation RU Saudi Arabia SA Senegal SN Singapore SG Slovakia SK Slovenia SI South Africa ZA South Korea KR Spain ES
Language Code Quechua 8185 Rhetoromaans 8277 Romanian 8279 Russian 8285 Samoan 8377 Sanskrit 8365 Scottish Celtic 7168 Serbian 8382 Servocroat 8372 Shona 8378 Sindhi 8368 Singalees 8373 Slovak 8375 Slovenian 8376 Spanish 6983 Sudanese 8385 Swahili 8387 Swedish 8386 Tagalog 8476
Zone Code Sri Lanka LK Sweden SE Switzerland CH Taiwan TW Thailand TH Turkey TR Uganda UG Ukraine UA United States US Uruguay UY Uzbekistan UZ Vietnam UN Zimbabwe ZW
Language Code Tajik 8471 Tamil 8465 Telugu 8469 Thai 8472 Tonga 8479 Turkish 8482 Turkmen 8475 Twi 8487 Ukrainian 8575 Urdu 8582 Uzbeeks 8590 Vietnamese 8673 Volapük 8679 Welsh 6789 Wolof 8779 Xhosa 8872 Yiddish 7473 Yoruba 8979 Zulu 9085

The remote does not work properly / not at all
Cannot match properly to radio stations
Blowling sound to be heard during DVD or CD playback
A DVD/CD is not played.
The image quality of the DVD is poor
There's little or no sound
No food. No visual.
Troubleshooting
There is an obstacle between the remote control and the device. The batteries in the remote control are exhausted.
The signal strength of the radio station is too weak. No drives have been programmed or the programmed drives deleted (while matching by scanning programmed channels). The remote control is not directly directed to the DVD receiver. The remote control is too far from the DVD receiver.
The disc is misplaced. The menu is open on the screen. The child lock is enabled so that the playback of DVD drives with a certain rating is not possible. The disc is dirty. The DVD receiver is too close to the TV which causes feedback. The antenna is poorly placed or badly connected.
No disk inserted. An unplayable disk is placed.
Equipment connected via the audio cable is not set to receive DVD signal output. The audio cables are not properly connected to the speakers or receiver. The audio cables are damaged. The disc is dirty.
The mains cable is disconnected. The TV is not set to receive the DVD signal. The video cables are not properly connected.
Replace the batteries with new ones.
Point the remote directly at the device. Use the remote control within 7 meters of the DVD receiver. Remove the obstacle.
Clean the disc with a soft cloth and wipe outward. Place the DVD receiver and audio components further away from the TV. Check the antenna connection and adjust the position. Mount an outdoor antenna if necessary. Agreed by hand at the station. Program certain stations, see page 15 for more information.
Replace with a new audio cable. Clean the disc with a soft cloth, wiping it out from the centre of the disk. Place a playable disc. Place a playable disk (check disc type, color system and region code). Place the disc with the label or printed side upwards. Press SETUP to close the menu screen. Enter your password or change the rating level.
Put the power cable in an outlet. Select the right video input mode on TV so that the image of the DVD receiver is displayed on the TV screen. Connect the video cables to both TV and DVD receiver. Select the correct input mode of the audio receiver so you can hear the sound from the DVD receiver. Connect the audio cables to the connection points.

HDMI, the HD MI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDmi licensing LLC.
Manufactured under license of U.S. patents 5.451.942, 5.956.674; 5.974.380; 5.978.762; 6.487.535 and other American and worldwide patent granted and applied for. DTS and DTS Digital Surround are registered trademarks, and the DTS logo dresses and symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All rights reserved.
. Manufactured under license from Dolby Laboratories.
In addition, this device can play DVD+R/RW and CD-R/ RW disks with audio titles, DivX, MP3, WMA and/or JPEG files. Some DVD±RW/DVD±r or CD-RW /CD-R cannot be played on this device due to the recording quality or physical state of the disk, or the properties of the recorder and security software.
DVD+RW: Video mode only.
DVD+R: Video mode only. Also two-layer drives are supported.
DVD-RW: Video mode only and finalized. You cannot play DVR-VR drives that are finished on this device.
DVD VIDEO: Discs with movies that you can buy or rent. DVD-R: Only video mode and finalized.
You need to set the disk format option to [Mastered] in order to make it compatible with LG players while formatting rewritable drives. If you set the option on Live File system, you cannot use it on LG players. (Mastered/Live File System: Disk Formatting System for Windows Vista)
THE USER MUST REALIZE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT, WHICH MAY CAUSE IMAGE MALFUNCTIONS. WHEN DISPLAYING 525 OR 625 PROGRESSIVE SCAN IMAGES ENCOUNTERS PROBLEMS, WE ADVISE THE USER TO CHANGE THE CONNECTION INTO . IF YOU HAVE ANY QUESTIONS REGARDING THE COMPATIBILITY OF OUR TV SETS WITH THE 525P AND 626P VERSIONS OF THIS EQUIPMENT, PLEASE CONTACT OUR CUSTOMER SERVICE.
It is prohibited by law to copy, transmit, display, broadcast, play and/or rent any copyrighted material without permission. This product is equipped with a copy protection developed by Macrovision. Copy security signals are recorded on some disks. When recording and playing images from these drives, there will be interference. This product uses copyright protection technology protected by certain US patents and other intellectual property rights of Macrovision Corporation and other right holders. Use of this technology to secure copyright rights should be approved by Macrovision Corporation and is intended only for domestic and restricted use, unless otherwise authorised by Macroview Corporation. Disarming and dismantling are prohibited.
. . This symbol means that the function explained in this user manual is not available with those specific media.
Display of the symbol

Design and specifications may be modified without prior notice.
Type: 2-way 3 speaker 2-way3 loudspeaker 1-way 1 speaker Impedance 4 ohm 4 uhm 3 ohh Weighed input 155 W 155 W 225 W Max. Power input 310 W 310 W 450 W Net dimensions (W x H x D) 280 x 1200 x 280 mm 330 x 110 x 95 mm 182 x 416 x 414 mm Net weight 4,5 kg 1.6 kg 8.2 kg
Stereo Mode 155 W + 155 W (4 ohm at 1 kHz, THD 10 %) Surround mode front: 155 W+ 155 W(THD 10 %) Middle*: 155W Surround*: 155 W + 165 W (4 ohm at1 kHz,THD 100%) Subwoofer*: 225 W (3 ohms at 30 Hz,TH 10 %)
FM tuner range 87.5 - 108.0 MHz or 65.0 - 74.0 MHz, 87.5-100.0 MHz FM middle frequency 10.7 MHz
Food See main label. Power consumption See main label. Net weight 3.9 kg Outer dimensions (W x H x D) 430 x 73 x 305 mm Allowed ambient temperature 5°C to 35°C, Operating mode: Horizontal Relative humidity 5% to 85% Laser Semiconductor laser, wavelength 650 mm
Front/Back Middle Passive Speakers Subwoofer
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.