EN
LG logo
Official user manual

LG HT-303SU

14 pages·635 KB·Home cinema·PDF·ENDEFRITNLJA
LG HT-303SU
Table of Contents 45 sections HT303SU-D0_DUT · WARNING · ELECTRICAL SHOCK HAZARD · DO NOT OPEN · … ShowHide
Page 1 of the LG HT-303SU user manual — Put your old device away
Page 1 · click to enlarge
Page 1

HT303SU-D0_DUT

WARNING

ELECTRICAL SHOCK HAZARD

DO NOT OPEN

LET OP: to reduce the risk of an electric shock, do not remove the valve (or rear).

WARNING about the Power Cable

It is recommended for most devices that they are connected to an assigned circuit; Namely a single wall contact circuit that only supplies power to the device and does not involve any further connections. Check the specifications in this user manual to be sure.

Inside there are no components which can be

The Commission has also proposed that the Member States should take into account all possible risks associated with this type of product. Please call approved maintenance personnel

A lightning with arrow in an isosceles triangle is intended to alert the user to the presence of a dangerous, uninsulated voltage in the product housing that can be so large as to present a risk of electric shock.

Do not connect too many devices to wall sockets. Overloaded wall sockets, loose or damaged wall socket, extension cords, damaged power cables or damaged or cracked cable isolation are dangerous. Any of these conditions can lead to electric shocks or fire. Periodic control of the cable of your device is necessary, and if the device shows signs of damage or wear-out, pull the plug out of the wall socket, do not use the device, and have the cable replaced by an exact copy of the component by an approved service centre.

The exclamation point in an isosceles triangle is intended to alert the user to important usage and maintenance instructions in the instruction manual provided with the device.

Protect the power cable from physical or mechanical abuse, such as bending, clamping, clamps, between a closed door, or walking over it. Note plugs, wall sockets and the point where the cable leaves the device.

LET OP: Do not place the device in a small space, such as a bookcase or similar closed area.

Remove the power cable by pulling the plug, not on the cable. Please note that the plug is easily accessible after you have installed the product.

CLASS 1 LASER PRODUCT CLASS 1 LASER PRODUCT LUOKAN 1 LAZER LAITE CLASS 1 LAER APPARAT CLASSE 1 PRODUIT LASER

Put your old device away

1. If the symbol with the cross-border mobile waste bin is on a product, this means that it is covered by European Directive 2002/96/EC. 2. Electrical and electronic products may not be supplied with household waste, but must be returned to special collection points designated by the local or national authorities. 3. The correct removal of your old device helps to prevent negative environmental and human health impacts. 4. Would you like more information about the removal of your old device? Please contact your municipality, the waste collection service or shop where you bought the product.

WARNING: This product is equipped with a Laser System. You should read the user manual carefully for proper use and keep it for future use. If the device needs maintenance, please contact an approved service centre. The use of controls, modifications or the execution of procedures other than specified herein may result in dangerous exposure to radiation. Avoid direct exposure to the laser beam and do not open the device. Visible laser radiation if opened. DON'T LOOK IN THE BEAM.

This product is made according to the EMC DIRECTIVE 2004/1008/EC, and Low Voltage Directive 2006/95/EC.

European Representative: LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere, The Netherlands (Tel: +31-036-547-8940)

Page 2 of the LG HT-303SU user manual — 5.1 Speaker Settings
Page 2 · click to enlarge
Page 2

SNEL STRAND GUIDE Connecting the loudspeaker system

Connect the speakers using the included speaker cables and ensure that the colours of the ports and cables match. Adjust the parameters (distance, level, etc.) of speakers for optimal surround viewing.

. . Make sure you connect the speaker cable to the right ports: + with + and . If the cables are switched, then the sound will be distorted and displayed with too few bass tones.

. . If you use front speakers with a low maximum input rating, adjust the volume carefully to ensure that loudspeakers are not overcharged.

(left, surround) Back speaker

Note the following Note that children do not push their hands or other objects into the *speaker channel. *Loudspeaker channel: A hallway for a full bass sound in the speaker cabinet ( housing).

5.1 Speaker Settings

LG HT-303SU — 5.1 Speaker Settings diagram (page 2)
Fig. 1 · 5.1 Speaker Settings
LG HT-303SU — 5.1 Speaker Settings diagram (page 2)
Fig. 2 · 5.1 Speaker Settings

Please enter the following settings for the built-in 5.1 channel surround decoder. 1. Press ENTER and 5.1 Speaker SetUp menu will appear. 2. Use b / B to select the desired speaker. 3. Adjust options using the v/V/b/B buttons. 4. After settings, return to the previous menu by pressing the RETURN button. Loudspeaker Selection Select a speaker you want to customize. [Front speakers (Links), Front speakers (Right), Center speaker (Center), SubWoofer(SubWooper), Rear speakers ( Right), Rear speaker (Link) ]

Volume Press 1/2 to adjust the output level of the selected speaker. (-6dB - 6dB)

Distance If you have speakers connected to your DVD/CD Receiver, setting the Distance will ensure that the player knows how far the sound should travel before reaching the listening point. This ensures that the sound arrives at all speakers simultaneously, regardless of distance. Press b/B to adjust the distance of the selected speaker. Test Press b/B to test the signals of each speaker. Adjust the volume to the volume of test signals stored in memory.

Front Left (L) →Middle → Front Right (R) ›Bottom Right (r) }Bottoth Left (l) ---SubWoofer

Show 7 more labels / short text on this page
Medium speaker · Front Speaker · Front Speaker · (right) · (left) · Rear Speaker · Subwoofer
Page 3 of the LG HT-303SU user manual — MP3 ACD
Page 3 · click to enlarge
Page 3

Introduction

Installation For use 3 Connecting to the TV 4 Connections of the antenna 4 Connection of the loudspeaker system 4 Optional Equipment Connections 4

Playable discs

In addition, this device can play a DivX file, DVD -RW, DvD +RW , CD-R/CD-RW containing audio titles, MP3, WMA and/or JPEG files.

. .

Control Use the Front Panel 5 Using the Remote Control .5-7

recording equipment or CD-R/RW (or DVD-RW, DVd+RW) disk itself, some CD- R/RV (or dvd-Rw, Dvd+rW) discs cannot be played on this unit.

Setup Basic settings 7 General control 7

. . Only DVD-R/RW disks written in

Video mode and completed, are supported by this player.

LANGUAGE 8 SCHERM 8 AUDIO 8 LOCK 9 Other 9 Preset radio stations 9

. . If there is a lot of data on a disk,

may take longer for this player to read the data than with other models.

. . Do not place a tape or label on one of the

Disc sides on (the labeled side or the included side).

. . Do not use irregularly shaped CDs (e.g. in

Play an Audio CD or MP3/WMA/JPG/DivX file Play a audio CD ormp3/Wma file. . .10 Programmed View 10 Watch a JPEG Disc 10 Play a DivX movie file 11 Additional features 11

heart shape or octagonal). This could cause interference.

Regional Code The regional code is printed on the back of this device. This device can only play DVD drives with the same label as on the back of the device or .

Comments on regional codes

Works with RDS 11

When you try to play a DVD with a regional code other than your DV DVd player's region code, "Check Regional Code" appears on the TV screen.

References Language codes 12 Country codes 12 Problems Solving 13 Specifications 14

. .Dolby ., .Pro Logic . and the double-D symbol are trademarks of Dolby Laboratories. Produced under license from Dolby Laboratories. Make sure that the above mentioned is included in the user manual.

For use

Produced under license according to U.S. Patent #'s: 5.451.942, 5.956.674; 5.974.380; 5.978.762; 6.487.535 & other American and global patents issued and pending. DTS and DTS Digital Surround are registered trademarks, and the DTS logos and symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All rights reserved.

Display of the symbol

You may see a TV screen appear when entering a function . . This means that the function mentioned in the manual is not available on that particular DVD or video CD. Symbols used in this manual

Making unauthorized copies of copyrighted material, including computer programs, files, broadcasts and audio recordings, may constitute a copyright infringement and this is a crime. Do not use this equipment for this type of device

When one of the following symbols is mentioned in a chapter, this means that this chapter applies to the discs representing the symbol.

purposes. Be responsible, respect copyright

DVD-V

DVD and rounded DV DVR/RW

MP3 ACD

Audio -cd.

WMA disc. JPEG disc. DivX-disc.

DIVX JPEG WMA

Page 4 of the LG HT-303SU user manual — Connection to video component
Page 4 · click to enlarge
Page 4

Installation

Do not touch the inner pins of the rear panel connections. Electrostatic discharge can cause permanent damage to the device.

Back of the TV

(left, surround) Back speaker

Back of the DVD/CD receiver To AUX IN AUDIO

(L/R)

Note the following Note that children do not push their hands or other objects into the *speaker channel. *Loudspeaker channel: A hallway for a full bass sound in the speaker cabinet ( housing).

AUDIO FROM(L/R)

Connect to the TV

Composite Video Connection Connect the MONITOR input of the DVD/CD Receiver to the Video IN input from the TV using the video cable (V) provided.

Connect the device to one of the following devices, taking into account the possibilities of your existing installation.

Connections of the antenna

. . Depending on the television set and other devices you wish to connect, there are several ways of connecting it. You can use one of the following connection methods.

Connect the FM/AM antennas to listen to the radio.

. . Connect the FM cable antennas to the Fm antenna connection.

. Please refer to the manuals of your television set, stereo installation or any other device in order to perform the connection as best possible. Please note:

. Ensure that the FM wire antenna is stretched out properly.

. . Keep the FM wire antenna as horizontal as possible after connecting it. Connection of the loudspeaker system

. . Ensure that the DVD/CD receiver is connected directly to the TV. Select the right AV input on TV.

. . Do not connect the DVD/CD receiver to your TV via your video player. The DVD receiver may be distorted by the safety system.

Connect the speakers using the included speaker cables and ensure that the colours of the ports and cables match.

SCART connection

Connect the EXPLANATION (to TV) EURO AV scart connection of the DVD/CD receiver to the corresponding inputs on the TV using the scart cable (T).

Adjust the parameters (distance, level, etc.) of speakers for optimal surround viewing.

Connection to video component

. . Make sure you connect the speaker cable to the right ports: + with + and . If the cables are switched, then the sound will be distorted and displayed with too few bass tones.

Connect the buses of the COMPONENT VIDEO-EXTRACTION from this device to the respective buses on the TV set by means of a Y PB PR (C) cable.

. . If your telescope is a high-definition television or digitally ready, you have the highest possible video resolution with DVD/CD receiver progressive scan output.

. . If you use front speakers with a low maximum input rating, adjust the volume carefully to ensure that loudspeakers are not overcharged. Optional Equipment Connections

. . If your TV does not accept your resolution settings, an abnormal image will appear on the screen. Please read the user manual of your TV to set a resolution that is accepted by your TV.

Connect a VCR to the AUX IN connections.

Show 10 more labels / short text on this page
Medium speaker · Antenna-câble FM (fournie) · Front Speaker · Front Speaker · (left) · (right) · Subwoofer · Rear Speaker · (right, msurround) · Back of VCR
Page 5 of the LG HT-303SU user manual — Control
Page 5 · click to enlarge
Page 5

Control

1 2 3 4 5 6 7 8

10. USB Port Connect the USB port of a USB memory (or MP3 player, etc) to the USb port at the front of the device.
LG HT-303SU — Control diagram (page 5)
Fig. 3 · Control
LG HT-303SU — Control diagram (page 5)
Fig. 4 · Control

Remove the USB Flash Station from the device. 1. Choose a different function mode or press STOP (x) twice. 2. Remove the USB device from the device.

. . Do not remove the USB device during use. . Music files (MP3/WMA), photo files (JPEG) and

9 10 10 11 11 12 12

  • Use the front panel 1. (/ [ [ ) POWER button Burns red if the receiver is in Standby mode (off). 2. SHITS 3 SCHERM window 4. Sensor Remote control: Operating Range Remote control Distance: About 7m (23 ft) from the front of the remote control Angle: Approximately 30 degrees in each direction of the front side of the Remote control 5. OPEN/CLOSE (OPEN/CLUT) Opens or closes the disc tray. 6.
  • (B / X ) PLAY/ PAUSE
  • FUNC.( - ) Hold this button for about 3 seconds, then press repeatedly to select another function. (DVD/CD → USB → AUX → TV -AUDIO → PORTABLE → FM) 7.VSM Press VSM to set the VIRTUAL sound.
  • 3D STEREO Realtime 3D sound technology with stereo sources, optimal for stereo speakers. Listeners can enjoy amazing virtual surround effects with their own multimedia players.
  • Multichannel sound The Multichannel audio changes the sound from 5.1 ch to a virtual sound in 10.1 ch so that it looks like you are listening to sound coming out of right, left and center speakers simultaneously. 8. TUNING(-/+) /SKIP/SCAN (SKIP /SCAN) (. / > ) Press TUNING repeatedly (-/+) for manual adjustment. For automatic alignment, hold TUNNING (-/+) on the front panel for about two seconds. 9. VOLUME controller Adjusts speaker volume.

Video files can be played. . . This device does not support USB HUB. . Recommended memory cards.

Compact Flash Card (CFC), Micro Drive (MD), Smart Media Card (SMC), Memory Stick (MS), Secure Digital Card (SD), Multimedia Card (MMC), Memory Stick Pro (MS-Pro) - Compatible with: FAT16, FAT32 - Use only the recommended memory cards. . .

are not supported after connecting the device to a computer. . . In the case of a USB HDD, make sure you have the extra

power cable connects to the USB HDD for proper use. Up to 2 primary partitions of a disk are supported. If there is an extension partition, up to four partitions can be supported. . . If there are two or more disks on the USB device, then the

directories shown on the screen. If you want to go to the initial menu after selecting a folder, press RETURN. . . Digital cameras and mobile phones are not supported. . . Supports USB 1.0/1.1 only (in case USB 2.0 is

inserted into the player, it is treated at the same speed as USB 1.1)

11 GATE IN Introduce TRUCKABLE Device If you connect a portable music player to the POORT. In input of this device using a ( 3.5mm) mini stereo cable (not supplied), you can listen to the sound performed by the portable device via speaker. 12. STOP

Use the remote control.

  • 1. 2. MUTE Press MUTE to turn off the sound of your device. You can turn off the sound of your device to answer the phone, for example. 3.
  • FUNCTION : (DVD/CD → FM )
  • INPUT: (USB → AUX → TV-- AUDIO → PORTABLE ) 4. DEEP You can automatically disable the DVD/CD Receiver at a pre-arranged time. 1. Press SLEEP to enter the desired sleep time. Sleep time appears in the screen window. 2. The setting changes as follows after each click of the SLEEP button. (DIMMER ON) → SLEEP 180 → 150 → 120 → 90 → 80 → 70 → 60 → 50 → 40 → 30 → 20 → 10 →( DIMMER OFF) Note: You can check the remaining time before the DVD/CD Receiver is disabled. Hit SLAPE. The remaining time will appear in the screen window. 5. RETURN Removes the Settings menu. 6. 0-9 numeric keys: Select a service, program number, directly or select the numbered options in a menu.
Page 6 of the LG HT-303SU user manual — ALL
Page 6 · click to enlarge
Page 6
13. b / B / v / V (left/right/up/down) Select an option from the menu.

ENTER Confirm the menu selection. PRESET(v/V) Press PRESET +/- repeatedly to select the desired programmed drive. Every time you press the button, the DVD/CD Receiver will tune to one programmed drive at a time. First program the drives programmed in DVD/CD Receiver memory (see . TUN.(-/+) (b/B) For manual adjustment, press TUN (-/+) Repeatedly. For automatic tuning, keep TUN. (-/+) pressed on the front panel for about two seconds.

14. SCAN(bb/BB) During playback press repeatedly SCAN (m or M) to select the required scanning speed. DVD, DivX: bb, bbb,bbbb,bbb, or BB, BBB, BBBB, BbbBB WMA/MP3, Audio CD: m (X2, X4, X8) or M (X2 X4, x8) . SLOW(bb/BB) In pause mode, press SLOW (m or M) to select the required speed. DVD: t (1/2, 1/4, 1/8, 1/16) or T (1/ 2, 1/4,1/8, 1/15) DivX: T ( 1/2, 1/ 4, 1/8, 1//16) 15. SKIP (. / >)When playing, press SKIP (. or >) to go to the next chapter/track or return to the beginning of the current chapter/ track. Press SKIP . two shorts, to go a step back in current chapter/track. 16. VOLUME (+/-) Adjusts speaker volume. 17. • PLAY(B) - Play disk and file. - 1.5 speed playback You can quickly enjoy a movie and music. The 1.5 speed allows you to view images and listen to the sound, faster than at normal playback speed on the disk. 1. Press the PLAY button during normal playback. The screen is shown at 1.5 speed with sound. 2. To return to normal playback, press PLAY. - FM mode status, select MONO or STEREO by

S-TITLE S- TITLE RDS RD'S PTY PTY REPEAT

CLEAR

7. EQ ( EQUALIZER Effect)

You can choose from 7 programmed sound impressions. Every time you press the button, the setting in the screen window changes according to the order below. • AUTO EQ : AUTO EQ only works on MP3 files with Tag information in the DVD or USB function. (ID3 Tag only works at far. 1). - WMA file works with Normal EQ regardless of the Tag information. NORMAL → NATURAL →(AUTO EQ)→ POP → CLASSIC → ROCK → JAZZ → NORMAL..

ACD WMA MP3 DVD

8. VSM Press VSM to set the VIRTUAL sound. You can enjoy surround sound by simply selecting one of the pre-programmed audio fields according to the program you want to listen to. Press the VSM button repeatedly.
  • Press the PLAY button on the remote.
  • PAUSE/STEP (X) During playback press X to pause playing. Press X repeatedly to play frame-for-frame.
  • STOP (x ) 18. PROG./MEMO. Opens or closes a program menu. Enter a frequency of a radio station into the tuner. 19. REC (z) - USB Record This feature allows you to record music from an AUDIO CD on a connected USB storage device. Read the comments on page 14 before you start recording USB.

- 2 Ch Source: BYPASS →VIRTUAL →ON STAGE →PLII MOVIE → PLUMI MUSIC → CLII MTRX→ BYPASS... - 5.1Ch Source: BYPASS →VIRTUAL →PASS

ALL

9. SETUP Opens or closes the Settings menu. 10. MENU Opens the menu on a DVD drive. 11. DISPLAY 1. Press SCHERM to view the different information on the loaded disk. The parts shown differ depending on the disk type or playback status. 2. You can select a part using v/V and change or select the setting by pressing b /B. 12. TITLE If the current DVD has a title, the title menu will be displayed on the screen. Otherwise, the disk menu will be displayed.

1. Place a USB device with sufficient space in the USB port on the device. 2.Select DVD/CD to record by pressing the FUNCTION button on the remote control. AUDIO CD - Press v/V to select the desired file/track. 3. Press REC (z) on the remote to start recording. . - Once you start the USB recording, the recording percentage will

  • Title (track) - Current title (or track) number/total number of titles (or tracks).
  • Chapter - Current chapter number/total number of chapters
  • Time - Provide playtime
  • Audio - Selected audio language or channel
  • Subtitles - Selected subtitles.
  • Angle - Selected angle/total number of angles
  • Sound - Selected sound mode Note: If no button is pressed for a few seconds, the onscreen screen will be closed.

speed while recording are shown on the screen window. 4. File is saved to CD REC in format .TRK 001.mp3a. 5. Press STOP to stop the recording.

DivX DVD

Page 7 of the LG HT-303SU user manual — Setup
Page 7 · click to enlarge
Page 7

Recording Audio CD source to USB

Set remote control codes for LG TV 1. Hold POWER (TV) and CHANNEL(v/V) press the button repeatedly to turn on or off the TV. 2. The buttons POWER (TV), CHANNEL(v/V), VOLUME (+/-), and INPUT are used on the remote to control the LG TV. Note: If the remote control does not operate your TV, try another code or use the remote that was provided with LG TV. (LG and Gold Star) Due to the large number of codes used by manufacturers, US BUSINESS cannot guarantee that remote control will be used on any LG TV model. DivX DVD

Recording a track: If the USB recording is played while playing the CD, the track will be recorded on the USb.

Record all tracks: If the USB Rec. button is pressed while the CD has stopped, all tracks will be recorded.

Add a list of programs: USB Recording after selecting the tracks, press the PROG./MEMO button to record your desired tracks.

20. SUBTITLE While playing, repeatedly press S-Title to select your desired subtitle language. 21. REPEAT During playback, press REPEAT repeatedly to select the desired repeat mode. DVD-Video Disks: Chapter/Title/From Audio CD, DivX/MP3/WMA Disks 22. RDS/ PTY Displays the different screens of RDS options. 23. CLEAR Removes a track number from the Program List. 24. TV - Control the TV Your remote control can control your DVD/CD Receiver, as well as certain functions of an LG TV. Follow the instructions below to control your LG TV.

Setup

Basic Settings

GENERAL OPERATION 1. Press SETUP. The Setup menu will be displayed. 2. Press v/V to select the desired option and press B to go to second level. On the screen, the current setting for the selected item is displayed as well as the other possible settings(s). 3. Press v/V to select the second option, and then press B to go to third level. 4. Press v/V to select the desired setting and then press ENTER to confirm your choice. For some items you need to perform additional steps. 5. Press SETUP or PLAY to exit the settings menu.

The Setup menu allows you to adjust numerous items, such as the image and sound. You can, among other things. also set the language for subtitles and settings menu. For more information on each item in the settings menu, please refer to pages 7 to 9.

a b c d e

LG HT-303SU — Setup diagram (page 7)
Fig. 5 · Setup

a Language - Menu/Disc Audio/Subtitles/Menu b SCHERM - TV Ratio / Screen Mode / Progressive

Select Scan/TV Output c AUDIO - 5.1 Speaker setting / Dynamic Range

Control (DRC) / Vocal d BORDERING (Old-age control) - Assessment /

Password / Region code e OTHERS - DivX(R) VOD / REC Bitrate

Show and exit the menu: Press SETUP to display the menu. A second press on SETUP will bring you back to the home screen. Move to the following level: Press B on the remote. Go to the previous level: Press b on the remote.

Page 8 of the LG HT-303SU user manual — Setup
Page 8 · click to enlarge
Page 8

LANGUAGE Menu: Select a language for the Setup menu and OSD. Disc Audio / Subtitles / Menu To select the language for displaying audio track (audio CD), subtitles and CD menu. Original - Refers to the original language in which the disc is recorded. Others - To select another language, press the numerical keys and then ENTER to enter the corresponding 4-digit number according to the language code list on page 12. Press CLEAR if you have entered the wrong language code.

Loudspeaker Selection Select a speaker you want to customize. [Front speakers (Links), Front speakers (Right), Center speaker (Center), SubWoofer(SubWooper), Rear speakers ( Right), Rear Speakers (Link)] Note: Certain loudspeaker settings are prohibited under the Dolby Digital License Agreement.

Size: From the moment that speaker settings are fixed, you cannot change the settings.

Volume: Press b/B to adjust the output level of the selected speaker. (-6dB - +6dB)

Distance: If you have speakers connected to your DVD/CD Receiver, setting the Distance will ensure that the player knows how far the sound should travel before reaching the listening point. This ensures that the sound arrives at all speakers simultaneously, regardless of distance. Press b/B to adjust the distance of the selected speaker.

SCHERM TV Ratio 4:3 . Select if a standard 4:3 TV is connected. 16:9 – Select if a 16:9 widescreen TV is connected. Display mode: The screen mode setting only works if the TV ratio mode is set to . Letterbox . . Displays a wide image with bands at the top and bottom of the screen. Panscan . Automatically displays the wide view on the entire screen and cuts away those parts that don't fit.

Test Press b/B to test the signals of each speaker. Adjust the volume to the volume of test signals stored in memory.

Front Left (L) →Middle → Front Right (R) ›Back Right (r) }Bottom Left (l) ►SubWoofer

Progressive Scan Progressive Scan Video provides high quality images with fewer flickerings. If you use the Component Video contact points to connect a TV or monitor that is compatible with progressive scan signal, set the option [Progressive Scan] to [On]. Press ENTER. - If you do not press ENTER within 10 seconds, [OFF] will become

DRC (Dynamic Range Control - Dynamic Range Control) Keeps the sound clear when lowering volume (Dolby Digital only). Set this effect to [ON].

Voxal Set Vocal only to [On] if a multichannel karaoke DVD is played. The karaoke channels on the disk are mixed to normal stereo sound.

uitgevoerd. - If you do not have a TV with progressive scan, the status will

progressive scan [On] not shown on screen. (then hold the STOP button on the remote control for 5 seconds to change to [OFF].) TV Export Select . . Select an option according to the TV connection type. [YPbPr]: If your TV is connected to the COMPONENT/PROGRESSIVE SCAN contact points of this device.

[RGB]If your TV is connected with a SCART

Contact point.

- COMPONENT OUT will not work if connected

by RGB. - In Progressive scan [on] status, the TV output is

selection mode inactive.

AUDIO Each DVD disc has a number of different audio output options. Set the AUDIO options of the DVD player using the type of audio system you are using.

5.1 Speaker Settings Please enter the following settings for the built-in 5.1 channel surround decoder. 1. Press ENTER and 5.1 Speaker SetUp menu will appear. 2. Use b / B to select the desired speaker. 3. Adjust options using the v/V/b/B buttons. 4. After settings, return to the previous menu by pressing the RETURN button.

Page 9 of the LG HT-303SU user manual — Preset radio stations
Page 9 · click to enlarge
Page 9

LOCK (Youth Protection Control or Parental Control)

Country Code Enter the code of the region whose defaults have been used to review the DVD video disk, based on the list on page 12. 1. Select "Land Code" from the LOCK menu and press B. 2. Follow Step 2 as described in the previous paragraph (Security Level). 3. Select the first character using v/V keys. 4. Press B and select the second character using v/V buttons. 5. Press ENTER to confirm your Country Code selection.

Security level: Blocks playing rated DVD drives based on content. Not all disks have been reviewed. 1. Select "Security level" from the LOCK menu and press B. 2. For access to the SLOT options, you must enter your password. If you have not done so, you are asked to do this now. Enter a password and press ENTER. Re-enter it and press ENTER for check. Press Erasing before pressing ENTER if you have made a mistake. 3. Select a censor rating from 1 to 8 using the v/V keys.

OTHER DivX(R) VOD Registration We provide you with the DivX® VOD (Video On Demand) registration code that allows you to rent videos using the DIVX®VOD service. Visit www.divx.com/vod for more information. 1. Select the .divX(R) VOD-option and press B. 2. Press ENTER while .Select .selection ., the registration code will be shown. Use the registration code to rent or buy DivX® VOD videos on www.divx.com/vod Follow the instructions and download the video to a disc to play on this player. 3. Press ENTER to close. Note: All videos downloaded from DivX® VOD can only be played on this player.

Security level 1-8: Censorship rate one (1) has the highest limitations and censorship rate eight (8) is the lowest. Unlock: If you select unlock, the Youth Protection Control is not active and then the disc will be displayed uncensored. 4. Press ENTER to confirm your censorship choice, and then press SETUP to close the menu.

Password You can enter or change a password. 1. Select Password from the LOCK menu and press B. 2. Follow step 2 above (Security level). To change the password, press ENTER as soon as the .v.Change .f option is marked. Enter the old password and check your new password. 3. Press SETUP to close the menu.

REC BitrateSet UBS recording Bitrate to 96kbps or 12kbp (see page 7)

If you have forgotten your password You can delete the password if you have forgotten it by performing the following steps: 1. Press SETUP to open the Settings menu. 2. Enter the 6-digit number . The password has been erased.

Preset radio stations

For fm reception you can program 50 preferred stations. Turn off the sound before you start tuning. 1. Press the remote FUNCTION (Function) until FM appears in the image window. 2. Hold TUN (-/+) for two seconds until the frequency indication changes, then release the button again. Scanning stops as soon as the DVD/CD Receiver tunes to a drive. 3. Press PROG./MEMO on the remote control. A program number flashes in the screen window. 4. Press PRESET +/- on the remote to select your desired program number. 5. Press PROG./MEMO again on the remote control. The station is being stored. 6. Repeat steps 3 to 6 to save other drives.

To tune to a station with a weak signal Press TUN (-/+) repeatedly in step 3 to tune manually at the drive.

To clear all saved drives Press the PROG./MEMO button. and hold the key in ca. 2 seconds pressed until . . allo on the screen appears and then press PROG./MEMO.; radio stations have been erased.

• If you happen to be in the ERASE ALL mode, but

do not want to erase the memory, then press no button. A few seconds later, the announcement "ERASE ALL" will automatically disappear from the display and normal mode will be restored.

Page 10 of the LG HT-303SU user manual — Play an Audio CD or MP3/WMA file
Page 10 · click to enlarge
Page 10

Play an Audio CD or MP3/WMA/JPEG/DivX file

Play an Audio CD or MP3/WMA file

This player can play Audio CDs or recorded MP3/WMA files. MP3/ WMA/ Audio CD After loading recorded MP3/WMA files or an Audio CD, a menu appears on the TV screen. Press v/V to select a track/file and press PLAY or ENTER to start playing. You can select different playback functions. See pages 5, 6 or 7.

is removed. - Skipping AUTO is not supported during playback.

View a JPEG disc This device can play disks with JPEG files. Before playing JPEG recordings, read the comments about JPEG Recordings on page 14.

ID3 TAG If you play a file containing information such as track titles, then you can see that information by pressing DISPLAY. [Song, Artist, Album, Genre, Comment ] -ID3 Tag is used in the MP3 file.

1. Place a disc and close the drawer. The JPEG menu will be displayed on the TV screen.

2. Press v/V to select a folder and press ENTER. A list of files is displayed in the folder. If you are in a list of files and wish to return to the folder overview, use the v/V keys on the remote control to select and press ENTER. 3. If you want to view a particular file, press v/V to select a file and hit ENTER or PLAY. When you are viewing a file, press STOP to return to the previous menu (JPEG menu).

. Press MENU to go to the next page.

. . On the mixed CD with MP3/WMA files and JPEG files, you can go back and forth between the MP3/ WMA- and Jpeg menu. Press Title and the word MUSIC or PHOTO will light up at the top of the menu.

. AUTO EQ is set for WMA/ MP3 file in the function DVD/CD,USB.

Programmed View This programming feature gives you the ability to store your favorite tracks of a particular disc in the device's memory. Each programming can contain 30 tracks. 1. Place a disc. Audio CD and MP3/WMA Disc:

. . There are four Slideshow speed options: > (Slow), >> (Normal), > >>> (Quick). Use v/V /b /B to select the speed. Then use b / B to confirm your choice and then press ENTER.

Slide ShowUse v Vb B to reduce the risk of exposure
2. Select a track in the .List . and press PROG./MEMO. . . Repeat to add additional tracks in the list.

graphics show Slide Show select and then press ENTER.

Stand still image: 1. Press PAUSE/STEP during the graphical presentation. The device is now entering PAUZE mode. 2. To get back to the graphics, press PLAY or again PAUSE/STEP.

3. In the Program List select the track you want to play. Press MENU to go to the next page.
4. Press PLAY or ENTER to start. The playback starts in the order you programmed the tracks. Play stops after all tracks in the Program List are played once.

Listening to music during a slideshow: You can listen to music during a slideshow, if the disk contains music and photo files. Use v/V /b /B

5. To resume normal playback from programmed playback, select a track of the AUDIO CD (or MP3/WMA) list and press PAYMENT.

to mark the icon and press ENTER to start the slideshow. . You cannot play the sound mode and the VIRTUAL sound (VSM)

adjust while playing the Music PHOTO ALBUM.

  • Repeat Programmed Tracks 1. Press REPEAT while playing a disk. The Repeat icon is displayed. 2. Press REPEAT to select the desired repeat mode.
  • TRACK: Repeats the current track.
  • ALL: Repeats all tracks in the program list.
  • Off(no screen): Nothing is repeated. Clear a Track from the Program List 1. Use v V to select the track you want to delete from the program list. 2. Press Clear. Repeat to remove additional tracks from the list. Clear the full program list

Go after another file.

Press SKIP once (. or >) while viewing an image to go to the next or previous file.

Rotate the image Press v /V while displaying an image to rotate the image clockwise or counterclockwise.

Press PROG./MEMO and the • • icon will be displayed. Select the icon .Clear Allo-Thank v/V and press ENTER.

Page 11 of the LG HT-303SU user manual — Find Program (PTY)
Page 11 · click to enlarge
Page 11

Play a DivX movie file

Additional Functions

You can play a DivX file on the USB device and Divx drive in the DVD/CD Receiver. 1. Place a disc and close the drawer. The FILM menu will appear on the TV screen. 2. Choose a folder using v/V and press ENTER. A list of files appears in the folder. If a file list has been opened and wants to return to the folder list, use the v/V buttons on the remote control to mark it and press ENTER. 3. If you want to see a particular file, press v/V to mark a file and press ENTER or PLAY. 4. Press STOP to close.

Search on time (Time Search) To start playing the disk at any time. 1. Press DISPLAY while playing. 2. Press v/V to select the timer icon; on screen . . 3. Enter the start time from left to right in hours, minutes and seconds. If you make a mistake entering the numbers, press CLEAR to delete the entered digits. Then enter the correct numbers. 4. Press ENTER to confirm. Playback starts from the selected time position.

Screen Saver The screen saver will appear when you use the DVD player for approx.

Saves the last scene This DVD player stores the last scene that was displayed from the latest disc. The scene is stored in memory, even if you remove the disc from the device or turn it off. If you place a disc the scene of which was saved, then the scene will be automatically called.

ACD DVD

change between the menus MUZIC, PHOTO and FILM. Press TITLE and MUSIC, PHOTO and FILM at the top of the menu is marked. Notes: . . Make sure to select .SUBTITLE ON . by pressing the

Selecting the system You need to set up an appropriate system mode for your TV system. If the display in the screen window . . PAUSE/STEP Pressed for more than 5 seconds on the remote control to select a system (NTSC, PAL or AUTO). . . As the selected system with your

subtitle file, every time before playing a DivX file. • If the subtitle contains more than two languages in the

file, only the original subtitles are available. . You cannot play the sound mode and the VIRTUAL sound (VSM)

edit while playing the DivX file.

TV is not in conformity, it is possible that the broadcasts are not received in colour. NTSC: Select if the DVD/CD receiver is connected to an NTSC TV device. PAL: Select if the DVD/CD receiver is connected to a PAL TV device. AUTO: Select if the DVD/CD receiver is connected to a multi-system TV device.

Working with RDS

This device is equipped with RDS (Radio Data System), which extends FM radio to a wide range of information. RDS, which is used in many countries nowadays, is a system for transmitting station data.

Setting up of the RDS If it is tuned to an FM drive, and it contains RDS data, the device will automatically display the station's information.

Find Program (PTY)

Do as follows to look up certain program types (PTY).

1. Press FUNCTION to select the FM mode.
2. Select a desired drive by pressing TUN (-/+). If the RDS signal is received, the screen will show the program service name (PS).
1. Press the remote control on FUNCTION and select fm mode.
3. Press RDS to call up the frequency.
2. Press the remote control on PTY. The last selected type of program appears in the view window.

Display options of the RDS The system RDS can transmit different information in addition to the main call signal that appears at the first radio station setting. If the RDS is functioning normally, the name of the radio station, the radio transmitter or the letters of the call signal will appear on the screen. By on the key RDS To press the remote control, you can choose different data types in succession: (PS →FREQUENCY →PTY →RT →CT)

3. Press PTY again to select the type of program you want.
4. After selecting the desired type of program, press TUN (-/+) (vote). The device is now switching to automatic tuning. Once a station is found, the search stops.

DivX DVD

Page 12 of the LG HT-303SU user manual — References
Page 12 · click to enlarge
Page 12

References

Language codes This list allows you to set the language you want for the following basic settings: Disc Audio, Disc Subtitle, Disk Menu.

Language Code Abkhazian 6566 Afar 6565 African 6570 Albanian 8381 Ameharic 6577 Arabic 6582 Armenian 7289 Assamese 6583 Azerbaijani 6590 Bashkir 6665 Basque 6985 Bengali 6678 Bhutani 6890 Bihari 6672 Breton 6682 Bulgarian 6671 Burmese 7789 Belarusian 6669 Cambodian 7577 Catalan 6765 Chinese 9072 Corsican 6779 Croatian 7282 Czech 6783 Danish 6865 Dutch 7876 English 6978 Esperanto 6979 Estonian 6984 Faröers 7079

Language Code Fiji 7074 Finnish 7073 French 7082 Galician 7176 Georgian 7565 German 6869 Greek 6976 Greenland 7576 Guarani 7178 Gujarati 7185 Hausa 7265 Hebrew 7387 Hindi 7273 Hungarian 7285 Iceland 7383 Indonesian 7378 Interlingua 7365 Irish 7165 Italian 7384 Japanese 7465 Javanese 7487 Kannada 7578 Kashmir 7583 Kazakhstan 7575 Kyrgyz 7589 Korean 7579 Kurdish 7585 Laothiaans 7679 Latin 7665 Latvian 7686

Language Code Lingala 7678 Lithuanian 7684 Macedonian 7775 Malagasy 7771 Malaysia 7783 Malayalam 7776 Maltese 7784 Maori 7773 Marathi 7782 Moldovan 7779 Mongolian 7778 Nauru 7865 Nepalese 7869 Norwegian 7879 Oriya 7982 Panjabi 8065 Pashto, Pushto 8083 Persian 7065 Polish 8076 Portuguese 8084 Quechua 8185 Rhaeto-Romans 8277 Romanian 8279 Russian 8285 Samoa 8377 Sanskrit 8365 Gaelic (Scotland) 7168 Serbian 8382 Servocroat 8372 Shona 8378 Sindhi 8368

Language Code Singhales 8373 Slovak 8375 Slovenian 8376 Somali 8379 Spanish 6983 Sudanese 8385 Swahili 8387 Swedish 8386 Tagalog 8476 Tadzjikistaans 8471 Tamil 8465 Tatar 8484 Telugu 8469 Thai 8472 Tibetan 6679 Tigrinya 8473 Tonga 8479 Turkish 8482 Turkmen 8475 Twi 8487 Ukrainian 8575 Urdu 8582 Uzbek 8590 Vietnamese 8673 Volapük 8679 Welsh 6789 Wolof 8779 Xhosa 8872 Yorish 7473 Yoruba 8979 Zuelu 9085

Country codes Use this list to enter your country.

Country Code Afghanistan AF Argentina AR Australia AU Austria AT Belgium BE Bhutan BT Bolivia BO Brazil BR Cambodia KH Canada CA Chile CL China CN Colombia CO Congo Costa Rica CR Croatia HR Czech RepublicCZ Denmark DK Ecuador EC Egypt EG El Salvador SV

Country Code Ethiopia ET Fiji FJ Finland FI France FR Germany DE United Kingdom GB Greece GR Greenland GL Heard and McDonald Islands HM Hong Kong HK Hungary HU India IN Indonesia ID Israel IL Italy IT Jamaica JM Japan JP Kenya KE Kuwait KW Libya LY Luxembourg LU

Country Code Malaysia MY Maldives MV Mexico MX Monaco MC Mongolia MN Morocco MA Nepal NP Netherlands NL Netherlands Antilles AN New Zealand NZ Nigeria NG Norway NO Oman OM Pakistan PK Panama PA Paraguay PY Philippines PH Poland PL Portugal PT Romania RO Russian Federation RU

Country Code Saudi Arabia SA Senegal SN Singapore SG Slovakia SK Slovenia SI South Africa ZA South Korea KR Spain ES Sri Lanka LK Sweden SE Switzerland CH Taiwan TW Thailand TH Turkey TR Uganda UG Ukraine UA United States US Uruguay UY Uzbekistan UZ Vietnam UN Zimbabwe ZW

Page 13 of the LG HT-303SU user manual — Symptom
Page 13 · click to enlarge
Page 13

Troubleshooting

Check the following guide for possible cause of a problem before contacting the service.

Symptom

Cause

Correction

No power.

  • The power cable is not connected.
  • Insert the power supply cable into the stop contact.
  • Put a disc in the device. (Check if the DVD or audio CD indicator in the D VD window is illuminated.)

There is power, but the DVD/CD receiver does not work.

  • There's no disc in it.

No visual.

  • The TV is not set to receive the DVD signal.
  • Select the right video input mode on TV so that the DVD image appears on the TV screen.
  • The video cable is not properly connected.
  • Connect the video cable to the contact buses.
  • The connected TV is not enabled.
  • Turn on the TV.

There is no sound or only a sound at a very weak strength.

  • The equipment connected to the audio cable is not set to receive DVD signals.
  • Select the right input mode on the audio receiver so you can listen to the sound of D VD/CD receiver.
  • Connect the audio cable properly to the sockets.
  • The audio cables are not properly connected.
  • The device connected to the audio cable is disabled.
  • Switch the device connected to the audio cable.
  • The sound cord's damaged.
  • Replace this.

The image is of poor quality.

  • The disc's dirty.
  • Clean the disc.

The DVD/CD receiver does not start with display.

  • Put a disc in. (Check if the DVD, or audio CD indicator in the DvD window is lit.)
  • There's no disc in it.
  • Put in a playable disc. (Check the type of disc, colour system and regional code.)
  • An unplayable disc was inserted.
  • The disc's in reverse.
  • Put the disc with the play side down.
  • Put the disc in the disc drawer in the guide.
  • The disc is not in the guide.
  • The disc's dirty.
  • Clean the disc.
  • Press SETUP key to disable the screen menu.
  • There's a menu on the TV screen.
  • Clear the classification function or change the classification level.
  • The classification is set.

A heavy hum or noise is heard.

  • The disc's dirty.
  • Clean the disc.
  • Connect the speakers and components well.
  • Move your TV so that it is further from the sound components
  • Connect the antennas correctly.
  • The speakers and components are not well connected.
  • The DVD/CD receiver is placed too close to the TV.

One cannot tune to radio stations

  • The antenna is improperly connected or placed.
  • Adjust the antennas and connect an external antenna if necessary.
  • The signal strength of the stations is too weak (at tuning with automatic alignment).
  • Tune to the station manually.
  • No preset or preset drives have been deleted (if tuned by searching for preset stations).
  • Set the stations in advance (page 9).

The remote control isn't working properly.

  • The remote control is not directed at the distance sensor of the DVD/CD receiver.
  • Point the remote control at the distance sensor of the DVD/CD receiver.
  • The remote control is too far away from the DVD/CD receiver.
  • Operation the remote control within a range of 23 feet (7m).
  • There is an obstruction between the remote control and the DVD/CD receiver.
  • Remove the obstruction.
  • The batteries in the remote control are exhausted.
  • Replace the batteries with new ones.
  • Nothing is displayed on the display.

The display on the front panel is too vague.

  • Press SLEEP(Dimmer) on the remote control.
Page 14 of the LG HT-303SU user manual — Speakers
Page 14 · click to enlarge
Page 14
  • MP3/WMA Disk compatiliteit with this device is limited as follows:
  • Sampling frequency: within 8 - 48 kHz (MP3), within 22.05 - 48kHz (WMA)
  • Bit rate: within 8 - 320kbps (MP3), 32 - 256kbps (WMA) Supported Ver: v2 , v7, v8, v9
  • File extensions: . .
  • CD-ROM file format: ISO9660
  • We recommend that you use Easy-CD Creator, which creates an ISO 9660 file system.
  • ThThe total number of characters for filename: maximum 8 characters (excluding file extensions such as mp3/wma).
  • They can't have special letters like / ? *: . . < > l etc.
  • The total number of files on the disk should be less than 650.
  • This player does not support files with extensions like bmp. Zip.
  • In case of a spec.out file, the following file will automatically be selected when playing files in order. Customers should be aware that permission is required for downloading MP3 / WMA files and music from the Internet. Our company has no rights to grant such permission. Permission must always be obtained from copyright
  • Playable DivX file: ".avi ", ".mpg ", '.mpeg ", ,".divx"
  • SubStation Alpha (sub-Rip) (substation: sub-Rep, sub-rup, substation): sub-station sub-stup, auto-dxt, subsub-stat, subdistrict, subscreen, subspace, subscript, subcode, subtitle, subtype, subline, subway, subtext, subsystem, subversion, subdirect, sub.
  • Playing Codec format: DIVX3.xx ", "DIVX4.xx " , " DIVx5.xx " ", 'MP43 "," 3IVX ".
  • Playable Audio format: "AC3 ", "DTS "," PCM ",""MP3 " and "WMA ".
  • Sampling frequency: Within 32 - 48 kHz (MP3), within 24 - 48 GHz (WMA)
  • Bit rate: within 32 - 320kbps (MP3), 40 - 192kbPS (WMA)
  • Max bitrate: USB: 4Mbps , CD: 4mbps, DVD: 7MbPS
  • Disks formatted in the Live file system cannot be played on this player.
  • If the name of the movie file differs from that of the subtitle file, the subtitling is not shown while playing a DivX file.
  • If you play a DivX file that is different from Divxspec, it may not work properly.

USB recording with this player is limited as follows: Note: - If you stop recording while playing, the file will

that is recorded at the time. - External HDD, Multi Card Reader, Locked Device and MP3

  • JPEG disk compatibility with this player is limited as follows:
  • Normal JPEG - Max pixel in width: 8902 pixel
  • Progressive JPEG - Max pixel in width: 1609 pixel
  • Maximum number of files: Less than 650.
  • Some disks may not work depending on recording format or the state of the drive.
  • File extensions: .jpg-s

player are not supported. - If you record more than 648 files in a CD REC

folder, ERROR is displayed on the screen. - USB recording is not performed in the status SACD, CD-G,

DTS disc. - During USB recording there is no musical sound and some

Tories, except POWER, STOP and SLEEP are not working. - If you take the device off or turn it off during recording,

are saved MP3 files not playing, and cannot be created a file. - USB recording time may vary depending on the

  • DivX disk compatibility with this player is limited as follows:
  • Available resolution: within 720x576 (W x H) pixels
  • The filename of the DivX subtitles is available on 45 characters.
  • If an impossible code is placed in the name of the DivX file, it will be shown as .
  • Frame speed: Less than 30 fps
  • If the video and audio structure of the recorded files is not crossed, no video or audio will be performed.

the speed of writing of the device. - During recording, you cannot change function and volume. - If you press the Rec button on the remote control, turn

All functions return sound mode to BYPASS. - USB port of the device cannot be connected to

PC. The device cannot be used as a storage unit. - USB recording is available within 20hz~16hz.

Specifications

General Power supply See the rear panel. Power consumption See the rear panel. Net weight 2.5 kg External dimensions (W x H x D) 360 x 62 x 305 mm Operating conditions Temperature: from 5°C to 35 degreesC. Operating status: horizontal. Operating humidity 5% to 85%

Amplifier Output current Front: 45 W + 45 W ( Rated Output power 30 W, THD 10 %) Centre*: 45W Surround*:45W + 45W ( Rated Performance 30 W , 4Ω at 1 kHz, THD 10 %) Subwoofer*: 75W (rated Output power 60 W, 8 Ω at 30 Hz, THR 10 %)

Speakers

SH33SU-S SH 33SU-W Impedance 4 Ω 8 Ω Net dimensions (WxHxD) 99 x 114 x 86 mm 156 x 325 x 320 mm Net weight (1EA) 0.5 kg 3.5 kg

Designs and specifications can be changed without a counter-notice.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the LG HT-303SU

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LG HT-303SU

Be the first to ask — other owners or our team will answer.

Original document

LG HT-303SU manual PDF

14 pages·635 KB·Home cinema·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…