Instruction/ maintenance manual of the product BL150 Bolens
Go to page of 20
BL100 BL150 2-Cycle Gas Trimmers iMPORTANT: READ SAFETY RULES AND iNSTRUCTiONS CAREFULLY PiN 769-01464 (11/04) PRINTED IN USA.
THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator's manual provides you with easy-to- understand operating instructions.
The purpose of safety symbols is to attract your attention to possible dangers, The safety symbols, and their explanations, deserve your careful attention and understanding.
• Add fuel in a clean, welPventilated outdoor area where there are no sparks or flames. Remove the fuel cap slowly, and only after the engine stops. Do not smoke while fueling or mixing fuel. Wipe up any spilled fuel from the unit immediately. • Avoid creating a source of ignition for spilled fuel.
SAFETY AND _NTERNAT_ONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for compHete safety, assemMy, operating and maintenance and repair information.
APPUCAT_ONS As a trimmer: • Cutting grass and Hight weeds Decorative trimming around trees, fences, etc. Fuem Cap / // Blue Choke Lever Primer Bumb D-Handle Shaft Grip "_ Throttme ControJ Start.
INSTALL AND ADJUST THE D-HANDLE 3. The squared boHthoHe in the handHe is to the right. 2. Insert the shouHder boHt into the squared hoHe in the handHe and push through, On the Heft side of the handHe, pHacethe washer on the boHt, then screw the wing nut onto the boHt.
OraL AND FUEL MmXH_G H_STRUCTmONS ON and/or improperly mixed fuel are the main reasons for the unit not running properly. Be sure to use fresh, cban unleaded fuel.
_AIAD!_| |_,|_, Operate this unit only in a • well- ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. WARNING" Avoid acddental starting. • Make sure you are in the starting position when pulling the starter rope (Fig.
HOLDING THE TRIMMER WARNING: AHways wear eye, hearing, foot and body protection to reduce the risk of injury when operating this unit, Before operating the unit, stand in the operating position (Fig.
MAmNTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the tame, These procedures shouHd also be a part of any seasonaH tune-up, NOTE: Some maintenance procedure.
For Use with Singme Line ONLY For Use with SplitLine TM or Singme Line FWg. 15 NOTE: SpHitLine TM can onHy be used with the unner tee[ with the shotted hones. SingHe [ine can be used on either type of inner reel Use Figure 15 to identify the inner tee[ you have.
mNSTALUNG A PREWOUND REEL 1. Hold the outer spool with one hand and unscrew the bump knob counterclockwise (Fig. 12). Inspect the boHt inside the bump knob to make sure it moves freeHy. RepHace the bump knob if damaged. 2. Remove the oHd inner reeH from the outer spooH (Fig.
SPARK ARRESTOR MAINTENANCE NOTE: The exhaust can onHyflow in one direction: AWAY from the engine. Pay chose attention when disassemMing the muffHer so you can put it back together correctHy. FaiHureto do so will damage the unit and may cause serious personaH injury.
Cmean Air Fimter The condition of the air fiiter is important to the operation of the unit, A dirty air fiiter will restrict air flow and change the air/fuei mixture, This is often mistaken for an out.
CLEANING WARNING: To serious personal injury, always turn your trimmer off and allow it to cool before you clean or service it, Use a small brush to clean off the outside of the unit.
CAUSE Empty fueHtank Primer buHb wasn't pressed enough Engine is flooded OHd or impropeHy mixed fueH FouHed spark pHug Mugged spark arrestor CAUSE Air fiHter is pHugged OHd or impropeHy mixed fue.
Engine Type .......................................................................................................................................... Air-CooHed, 2-Cycle Stroke .........................................................................
California / EPA Emission ControJ Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board, the Envkonmentd Protection Agency and MTD LLC (MTD) are pHeased to exphin .
MANUFACTURER'S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories.
An important point after buying a device Bolens BL150 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bolens BL150 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bolens BL150 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bolens BL150 you will learn all the available features of the product, as well as information on its operation. The information that you get Bolens BL150 will certainly help you make a decision on the purchase.
If you already are a holder of Bolens BL150, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bolens BL150.
However, one of the most important roles played by the user manual is to help in solving problems with Bolens BL150. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bolens BL150 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
