
User's Guide
Machine type(s):
Model(s):


Conventions
Different types of caution statements include:
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Safety information 5

CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a service representative.
Safety information 6

SAVE THESE INSTRUCTIONS.
Safety information 7

Using this guide
This User’s Guide provides general and specific information on using the printer models that are listed on the cover page.
The following chapters contain information applicable to all printer models:
To find instructions for your printer:
Overview 8

Overview 9

Selecting a location for the printer 10
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any hardware options, then leave enough room for them also. It is important to:
Ambient temperature 15.6 to 32.2°C (60 to 90°F)
Storage temperature ‑40 to 60°C (-40 to 140°F)


Selecting a location for the printer 11


Additional printer setup 12
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Remove the controller board access cover.



Additional printer setup 13
2 Using a screwdriver, loosen the screws on the controller board shield.


3 Remove the shield.


Additional printer setup 14
4 Use the following illustration to locate the appropriate connector:

1 Lexmark Internal Solutions Port or printer hard disk connector
2 Option card connector
3 Memory card connector

Additional printer setup 15
5 Align the screws with the holes on the shield, and then reattach the shield.
6 Tighten the screws on the shield.

Additional printer setup 16
7 Reattach the access cover.


CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
An optional memory card can be purchased separately and attached to the controller board.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 12.
2 Unpack the memory card.
3 Align the notch (1) on the memory card with the ridge (2) on the connector.


Additional printer setup 17
4 Push the memory card straight into the connector, and then push the card toward the controller board wall until it clicks into place.

5 Reattach the controller board shield, and then the controller board access cover.
The controller board supports one optional Lexmark Internal Solutions Port (ISP).
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 12.
2 If an optional printer hard disk is installed, then remove the printer hard disk first.
For more information, see “Removing a printer hard disk” on page 27.

Additional printer setup 18
3 Unpack the ISP kit.


2 Screw for attaching the plastic bracket to the ISP
3 Screws for attaching the ISP mounting bracket to the controller board shield
4 Remove the metal cover from the ISP opening. a Loosen the screw.

b Lift the metal cover, and then pull it out completely.
1 ISP solution · 4 Plastic bracket

Additional printer setup 19



5 Align the posts of the plastic bracket with the holes on the controller board cage, and then press the plastic bracket on the controller board cage until it clicks into place. Make sure the cables are neatly tucked under the plastic bracket.


6 Install the ISP on the plastic bracket.


Additional printer setup 20
7 Lower the ISP toward the plastic bracket until the ISP is seated between the guides of the plastic bracket.


8 Use the provided thumbscrew for the ISP to attach the plastic bracket to the ISP.


Additional printer setup 21
9 Attach the two provided screws to secure the ISP mounting bracket to the controller board shield.


10 Tighten the thumbscrew that is attached to the ISP.
11 Connect the ISP solution interface cable into the receptacle of the controller board.



Additional printer setup 22
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 12.
2 Unpack the optional card.
3 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the controller board.


4 Push the card firmly into place as shown in the illustration.


Additional printer setup 23
5 Close the controller board access door.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 12.
2 Unpack the printer hard disk.

Additional printer setup 24
3 Locate the appropriate connector on the controller board cage.



Additional printer setup 25
To install a printer hard disk onto the ISP:
a Remove the screws attached to the printer hard disk mounting bracket, and then remove the bracket.

b Align the standoffs of the printer hard disk to the holes in the ISP, and then press the printer hard disk
down until the standoffs are in place.
Installation warning: Hold only the edges of the printed circuit board assembly. Do not touch or press on the center of the printer hard disk. Doing so may cause damage.

c Insert the plug of the printer hard disk interface cable into the receptacle of the ISP.

Additional printer setup 26

4 Align the standoffs of the printer hard disk to the holes in the controller board cage, and then press the printer hard disk down until the standoffs are in place.
Installation warning: Hold only the edges of the printed circuit board assembly. Do not touch or press on the center of the printer hard disk. Doing so may cause damage.

5 Insert the plug of the printer hard disk interface cable into the receptacle of the controller board.

Additional printer setup 27


CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.

Additional printer setup 28
1 Access the controller board.
For more information, see “Accessing the controller board” on page 12.
2 Unplug the printer hard disk interface cable from the controller board, leaving the cable attached to the printer hard disk. To unplug the cable, squeeze the paddle at the plug of the interface cable to disengage the latch before pulling out the cable.
3 Remove the screws holding the printer hard disk in place.



Additional printer setup 29
4 Remove the printer hard disk.
5 Set aside the printer hard disk.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Install the printer and any hardware options you have purchased in the following order:
For more information on installing a caster base, optional 550‑ or 250‑sheet tray, spacer, or 2100‑sheet tray, see the setup sheet that came with the option.

Additional printer setup 30
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Turn off the printer using the power switch, and then unplug the power cord from the electrical outlet.


2 Unpack the optional tray, and then remove all packing material.
3 Pull out the tray completely from the base.


4 Remove any packing material from inside the tray.
5 Insert the tray into the base.
6 Place the tray near the printer.
7 Align the optional tray with the caster base.

Additional printer setup 31

8 Align the printer with the tray, and then slowly lower the printer into place.

Additional printer setup 32

9 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.

Additional printer setup 33



To uninstall the optional trays, slide the latch on the right side of the printer toward the front of the printer until it clicks into place, and then remove stacked trays one at a time from the top to the bottom.
Connect the printer to the computer using a USB cable or Ethernet cable.
Make sure to match the following:

Additional printer setup 34




1 Parallel port Connect the printer to a computer.
2 USB port Attach an optional wireless network adapter.
3 Ethernet port Connect the printer to a network.
4 USB printer port Connect the printer to a computer.
5 Security slot Attach a lock that will secure the controller board.
6 Printer power cord socket Connect the printer to a properly grounded electrical outlet.
After attaching the Ethernet cable and power cord, neatly tuck the cables in the channels at the back of the printer.

Additional printer setup 35


2 Run the installer, and then follow the instructions on the computer screen.
3 For Macintosh users, add the printer.
1 Open the printers folder.

Additional printer setup 36
3 Navigate to the Configuration tab, and then select Update Now ‑ Ask Printer.
4 Apply the changes.
1 From System Preferences in the Apple menu, navigate to your printer, and then select Options & Supplies.
2 Navigate to the list of hardware options, and then add any installed options.
3 Apply the changes.
To configure your printer to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.

Additional printer setup 37
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are four basic options for Security Method: – WEP key
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless
utility of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point, or contact your system support person. – To find the WPA/WPA2 preshared key or passphrase for the wireless network, see the documentation
that came with the access point, see the Embedded Web Server associated with the access point, or consult your system support person.
Before you begin, make sure that:
– > Settings > > Network/Ports > > Active NIC > > Auto >
> Network/Ports > Active NIC > Auto

Additional printer setup 38
> Network/Ports > Active NIC > Auto > Submit
1 From the printer control panel, navigate to one of the following:
> > Wireless Connection Setup >
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wireless Connection Setup
2 Select a wireless connection setup.
Search for networks Show available wireless connections.
Enter a network name Manually enter the SSID.
Wi‑Fi Protected Setup Connect the printer to a wireless network using Wi‑Fi Protected Setup.
3 Follow the instructions on the printer display.
Before connecting the printer to a wireless network, make sure that:
1 Depending on your printer model, navigate to either of the following:
Wireless > > Wi‑Fi Protected Setup > > Start Push Button Method
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wi‑Fi Protected Setup > Start Push Button Method
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wi‑Fi Protected Setup > Start Push Button Method
2 Follow the instructions on the printer display.
Use To

Additional printer setup 39
1 Depending on your printer model, navigate to either of the following:
Wireless > > Wi‑Fi Protected Setup > > Start PIN Method
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wi‑Fi Protected Setup > Start PIN Method
> Network/Ports > Network [x] > Network [x] Setup > Wireless > Wi‑Fi Protected Setup > Start PIN Method
2 Copy the eight–digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address field.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the setting.
Before you begin, make sure that:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.
5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on.
6 To verify if your printer is connected to the network, print a network setup page. Then in the Network Card [x] section, see if the status is Connected.

Additional printer setup 40
1 Set the parameters in the printer. a From the control panel, navigate to the menu for the port settings. b Locate the menu for the serial port settings, and then adjust the settings, if necessary.
c Apply the changes.
2 From your computer, open the printers folder, and then select your printer.
3 Open the printer properties, and then select the COM port from the list.
4 Set the COM port parameters in Device Manager.
When all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly by printing the following:
For more information, see the following:
– “Printing a menu settings page” on page 74 for non‑touch‑screen printer models – “Printing a menu settings page” on page 122 or “Printing a menu settings page” on page 170 for
touch‑screen printer models • Network setup page—Use this page to verify the network connection. This page also provides important information that aids network printing configuration.
For more information, see the following:
– “Printing a network setup page” on page 75 for non‑touch‑screen printer models – “Printing a network setup page” on page 122 or “Printing a network setup page” on page 170 for
touch‑screen printer models

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 41
Learning about the printer


2 Printer control panel
4 Standard 550‑sheet tray (Tray 1)
1 Standard bin · 3 Multipurpose feeder

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 42
The following illustration shows the maximum number of optional finishers and trays that are supported by the printer. For more information on other configurations, visit www.lexmark.com/multifunctionprinters.


Hardware option Alternative hardware option
3 Caster base None
4 2100‑sheet tray None
5 550‑sheet tray 250‑sheet tray
6 250‑sheet tray 550‑sheet tray
7 4‑bin mailbox Output expander
8 Output expander 4‑bin mailbox
The staple, hole punch finisher must not be combined with any other output options.
In a configuration with two or more optional finishers:

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 43
When using optional trays:
1 2 3 4 5

6 7 8 9 10

2 Select button Submit changes made in the printer settings.
3 Arrow buttons Scroll up and down or left and right.
5 Sleep button Enable Sleep mode or Hibernate mode.
Do the following to wake the printer from Sleep mode:
6 Stop or Cancel button Stop all printer activity.
9 Indicator light Check the status of the printer.
10 USB port Connect a flash drive to the printer.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 44
The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition.
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Solid green The printer is on, but idle.
Blinking red The printer requires user intervention.
Sleep button light Printer status
Off The printer is off, idle or in Ready state.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern
The printer is in Hibernate mode.
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 263 and “Storing paper” on page 182.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Paper Size/Type >
2 Press the up or down arrow button to select the tray or feeder, and then press .
3 Press the up or down arrow button to select the paper size, and then press .
4 Press the up or down arrow button to select the paper type, and then press to change the settings.
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 45
From the printer control panel, navigate to:
> Settings > > Paper Menu > > Universal Setup > > Units of Measure > > select unit of
1 Pull out the tray.

measure >

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 46
2 Squeeze and slide the width guide to the correct position for the size of the paper being loaded until it clicks into place.



Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 47
3 Unlock the length guide, and then squeeze and slide the guide to the correct position for the size of the paper being loaded.



Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 48
4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack with the printable side facedown.

Without an optional staple finisher With an optional staple finisher


Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 49



Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 50


Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 51

6 For custom‑ or Universal‑size paper, adjust the paper guides to lightly touch the sides of the stack, and then lock the length guide.
7 Insert the tray.

8 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 52
1 Pull out the tray.
2 Adjust the width and length guides.
Loading A5‑size paper
a Pull up and slide the width guide to the position for A5.



Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 53
b Squeeze and slide the length guide to the position for A5 until it clicks into place.

c Remove the A5 length guide from its holder.


d Insert the A5 length guide into its designated slot.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 54


Loading A4‑, letter‑, legal‑, oficio‑, and folio‑size paper
a Pull up and slide the width guide to the correct position for the size of the paper being loaded.


Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 55
b If the A5 length guide is still attached to the length guide, then remove it from its place. If the A5 length
guide is not attached, then proceed to step d.

c Put the A5 length guide in its holder.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 56
d Squeeze the length guide and slide it to the correct position for the size of the paper being loaded until
it clicks into place.

3 Flex and fan the sheets to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load the paper stack with the printable side facedown.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 57

Without an optional staple finisher With an optional staple finisher


Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 58


5 Insert the tray.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 59

6 From the printer control panel, set the size and type in the Paper menu to match the paper loaded in the tray.
1 Pull down the multipurpose feeder door.

EXEC
A4 A5
LTR

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 60
2 Pull the multipurpose feeder extender.

LTR
B5
EXEC
3 Slide the width guide to the correct position for the size of the paper being loaded.

A4 A5
EXEC
B5

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 61

B5
4 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load paper or specialty media.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 62
Without an optional staple finisher With an optional staple finisher

ABC
One‑sided printing
One‑sided printing

Two‑sided printing
Two‑sided printing
One‑sided printing Two‑sided printing


Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 63

LTR
B5
EXEC


6 For custom- or Universal-size paper, adjust the width guides to lightly touch the sides of the stack.
7 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 64
The printer links trays when the specified paper size and type are the same. When a linked tray becomes empty, paper feeds from the next linked tray. To prevent trays from linking, assign a unique custom paper type name.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a new custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 65
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Names
2 Select a custom name, and then type a new custom paper type name.
3 Press .
4 Press Custom Types, and then verify if the new custom paper type name has replaced the custom name.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type.
4 Click Submit.
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Types
2 Select a custom paper type name, and then select a paper type.
3 Press .

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 66
1 From the document that you are trying to print, open the Print dialog.
2 If necessary, adjust the settings.
3 Send the print job.
Using the Embedded Web Server
1 Open a Web browser, and then type the IP address of the printer in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness, and then click Submit.
Using the printer control panel
1 From the printer control panel, navigate to:
> Settings > > Settings > > Print Settings > > Quality Menu > > Toner Darkness
2 Adjust the toner darkness, and then press .

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 67
1 Insert a flash drive into the USB port.



Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 68
2 From the printer control panel, select the document you want to print.
3 Press the left or right arrow button to specify the number of copies for printing, and then press .
Recommended flash drives File type
Documents:
Images:

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 69
Mopria® Print Service is a mobile printing solution for mobile devices running on Android version 4.4 or later. It allows you to print directly to any Mopria‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Tap Print, and then select the printer.
3 Send the print job.
Google Cloud PrintTM is a mobile printing service that allows enabled applications on mobile devices to print to any Google Cloud Print‑ready printer.
1 From the home screen of your mobile device, launch an enabled application.
2 Tap Print, and then select the printer.
3 Send the print job.
AirPrint is a mobile printing solution that allows you to print directly from Apple devices to an AirPrint‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Select an item to print, and then tap the share icon.
3 Tap Print, and then select a printer.
4 Print the document.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 70
Lexmark Mobile Print allows you to send documents and images directly to a supported Lexmark printer.
1 Open the document, and then send or share the document to Lexmark Mobile Print.
2 Select a printer.
3 Print the document.
1 From the printer control panel, navigate to:
> Settings > > Security > > Confidential Print > select the print job type
Print job type Description
Max Invalid PIN Limits the number of times an invalid PIN can be entered.
Confidential Job Expiration Lets you hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Lets you print and store print jobs in the printer memory for reprinting.
Verify Job Expiration Lets you print one copy of a print job while the printer holds the remaining copies. It allows you to examine if the first copy is satisfactory. The print job is automatically deleted from the printer memory once all copies are printed.
Reserve Job Expiration Lets you store print jobs for printing at a later time. The print jobs are held until deleted from the Held Jobs menu.
2 Press .

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 71
1 From the document you are trying to print, open the Print dialog.
3 Select the print job type.
4 If necessary, assign a user name.
5 Send the print job.
6 From the printer home screen, select Held Jobs.
7 Send the print job.
1 From the printer control panel, navigate to:
> Settings > > Reports > > Print Fonts
2 Press the up or down arrow button to select the font setting.
3 Press .
From the printer control panel, navigate to:
> Settings > > Reports > > Print Directory >
1 From the printer control panel, press .
2 When a list of print jobs appears, select the job to cancel, and then press .
3 Press to go back to the home screen.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 72
For Windows users
1 Open the printers folder, and then select your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
1 From System Preferences in the Apple menu, navigate to your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
The remote control panel on your computer screen lets you interact with the printer control panel, even when you are not physically near the network printer. From your computer screen, you can view the printer status and do print-related tasks you might normally do while standing at the network printer.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Press Enter to open the Web page of your printer.
3 Click Applications.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 73
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e‑mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached, and the user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops processing jobs when the supply condition is reached. The supply
must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings tab > Security > Confidential Print Setup.
Notification Description

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 74
4 Save the modified settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click the Copy Printer Settings.
3 To change the language, select a language from the drop-down menu, and then click Click here to submit language.
4 Click Printer Settings.
5 Type the IP addresses of the source and target printers in their appropriate fields.
6 Click Copy Printer Settings.
Print a menu settings page to review the current menu settings and to verify if the printer options are installed correctly.
From the printer control panel, navigate to:
> Settings > > Reports > > Menu Settings Page >

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 75
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the printer control panel, navigate to:
> Settings > > Reports > > Network Setup Page >
2 Check the first section of the network setup page, and then confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult your system support person for a solution, and then print another network setup page.
From the printer control panel, navigate to:
> Status/Supplies > View Supplies >
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.
Using Eco‑Mode
1 Open a Web browser, and then type the printer IP address in the address field.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 76
2 Click Settings > General Settings > Eco‑Mode.
3 Select a setting.
Off Use the factory default settings for all settings associated with Eco‑Mode.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
Plain Paper Enable the automatic two‑sided (duplex) printing feature.
4 Click Submit.
Enable Quiet mode to reduce the printer noise.
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Quiet Mode >
2 Select a setting.
Use To

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 77
On Reduce printer noise.
Off Use factory default settings.
3 Press .
1 From the control panel, navigate to:
> Settings > > Settings > > General Settings > > Timeouts > > Sleep Mode >
2 In the Sleep Mode field, select the number of minutes the printer is idle before it enters Sleep mode.
3 Apply the changes.
Hibernate is an ultra‑low‑power saving mode.
1 From the control panel, navigate to:
> Settings > > Settings > > General Settings >
2 Select Press Sleep Button or Press and Hold Sleep Button, and then press .
3 Press Hibernate > .
Use To

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 78
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 74.
If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 80.
From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Factory Defaults > > Restore Now
The printer is equipped with a security lock feature. When a lock compatible with most laptop computers is attached, the printer is locked. When locked, the controller board shield and the controller board cannot be removed. Attach a security lock to the printer in the location shown.


Your printer contains various types of memory that can store device and network settings, and user data.
>

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 79
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, device settings, network information, bookmark settings, and embedded solutions.
Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for device-specific functionality. This lets the device retain buffered user data from complex print jobs, as well as form data, and font data.
Erase the content of any installed printer memory in the following circumstances:
Disposing of a printer hard disk
In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, turn off the printer.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 80
Erasing non‑volatile memory
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 on the keypad while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Press the up or down arrow button until Wipe All Settings appears.
The printer will restart several times during this process.
4 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.
Using the printer control panel
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
4 Press the up or down arrow button until Yes appears, and then proceed with disk wiping.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 81
5 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.
Enable hard disk encryption to prevent loss of sensitive data in the event the printer or its hard disk is stolen.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Disk Encryption.
3 From the Disk Encryption menu, select Enable.
Using the printer control panel
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Navigate to:
Disk Encryption > Enable
4 Select Yes to proceed with disk wiping.

Using MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, MS818dn 82
5 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.

Learning about the printer


2 Printer control panel
4 Standard 550‑sheet tray (Tray 1)
Using MS810de 83 · 1 Standard bin · 3 Multipurpose feeder

The following illustration shows the maximum number of optional finishers and trays that are supported by the printer. For more information on other configurations, visit www.lexmark.com/multifunctionprinters.


Hardware option Alternative hardware option
3 Caster base None
4 2100‑sheet tray None
5 550‑sheet tray 250‑sheet tray
6 250‑sheet tray 550‑sheet tray
7 4‑bin mailbox Output expander
8 Output expander 4‑bin mailbox
Using MS810de 84

The staple, hole punch finisher must not be combined with any other output options.
1 2 3 4


3 Sleep button Enable Sleep mode or Hibernate mode. Do the following to wake the printer from Sleep Mode:
5 Stop or Cancel button Stop all printer activity.
6 Indicator light Check the status of the printer.
Using MS810de 85

7 USB port Connect a flash drive to the printer.
The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition.
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Solid green The printer is on, but idle.
Blinking red The printer requires user intervention.
Sleep button light Printer status
Off The printer is off, idle or in Ready state.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern
The printer is in Hibernate mode.
When the printer is turned on, the display shows a basic screen, referred to as the home screen. Use the home screen buttons and icons to initiate an action.
1 2 3 4

5 6 7 8
Using MS810de 86 · Use the To

1 Change Language Change the primary language of the printer.
2 Bookmarks Create, organize, and save a set of bookmarks (URLs) into a tree view of folders and file links.
3 Held Jobs Display all current held jobs.
4 USB View, select, or print photos and documents from a flash drive.
5 Menus Access printer menus.
8 Tips View a context‑sensitive help information.
These may also appear on the home screen:

Jobs by user Access print jobs saved by user.

If an attendance message affects a function, then this icon appears and the red indicator light blinks.
The IP address of your printer is located at the top left corner of the home screen. You can use the IP address when accessing the Embedded Web Server to view and remotely configure printer settings.
Using MS810de 87 · Touch To


1 Radio button Select or clear an item.
2 Up arrow Scroll up.
3 Down arrow Scroll down.
4 Accept button Save a setting.
Return to the home screen.
Open a context-sensitive Help dialog on the printer control panel.
Scroll to the left.
Scroll to the right.
Using MS810de 88 · Touch the To · Touch To

1 In the Run dialog box, type cmd to open the command prompt.
2 Type ipconfig, and then look for the IP address.
1 From System Preferences in the Apple menu, select Network.
2 Select your connection type, and then click Advanced > TCP/IP.
3 Look for the IP address.
You can find the printer IP address:
The Embedded Web Server is the printer Web page that lets you view and remotely configure printer settings even when you are not physically near the printer.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
Using MS810de 89

1 Open a Web browser, and then type the printer IP address in the address field.
2 Do one or more of the following: • Show or hide the icons of basic printer functions. a Click Settings > General Settings > Home screen customization. b Select the check boxes to specify which icons appear on the home screen.
Your printer comes with preinstalled home screen applications. Before you can use these applications, you must first activate and set up these applications using the Embedded Web Server. For more information on accessing the Embedded Web Server, see “Accessing the Embedded Web Server” on page 89.
For more information on configuring and using the home screen applications, do the following:
1 Go to http://support.lexmark.com.
3 Click the Manuals tab, and then select the document for the home screen application.

The application lets you customize the background and idle screen of your printer home screen.
1 From the home screen, navigate to:
Change Background > select background to use
Using MS810de 90 · Icon Description · 2 Touch


Streamline work processes by letting you quickly find and print frequently used online forms directly from the printer home screen.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management > Forms and Favorites.
3 Click Add, and then customize the settings.
4 Click Apply.
To use the application, touch Forms and Favorites on the printer home screen, and then navigate through form categories, or search for forms based on a form number, name, or description.
Understanding Eco‑Settings

The application lets you easily manage energy consumption, noise, toner, and paper usage settings to help reduce the environmental impact of your printer.
Using MS810de 91 · Use To · Icon Description

You can export configuration settings into a text file, and then import the file to apply the settings to other printers.
1 Open a Web browser, and then type the printer IP address in the address field.
2 To export or import a configuration for one application, do the following: a Click Settings > Apps > Apps Management. b From the list of installed applications, click the name of the application you want to configure.
c Click Configure, and then do either of the following:
– When saving the configuration file, you can type a unique file name or use the default name. – If a "JVM Out of Memory” error occurs, then repeat the export process until the configuration
file is saved. • To import a configuration from a file, click Import, and then browse to the saved configuration file that was exported from a previously configured printer.
– Before importing the configuration file, you can choose to preview it first or load it directly. – If a timeout occurs and a blank screen appears, then refresh the Web browser, and then click
Apply.
3 To export or import a configuration for multiple applications, do the following: a Click Settings > Import/Export. b Do either of the following:
This application enables you to interact with the printer control panel even when you are not physically near the network printer. From your computer, you can view the printer status, release held print jobs, create bookmarks, and do other print-related tasks.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Remote Operator Panel Settings.
Using MS810de 92

3 Select the Enable check box, and then customize the settings.
4 Click Submit.
To use the application, click Remote Operator Panel > Launch VNC Applet.
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 263 and “Storing paper” on page 182.
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select the paper size or type >
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select a unit of measure
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch
1 Pull out the tray.
Using MS810de 93


2 Squeeze and slide the width guide to the correct position for the size of the paper being loaded until it clicks into place.

Using MS810de 94


3 Unlock the length guide, and then squeeze and slide the guide to the correct position for the size of the paper being loaded.

Using MS810de 95


4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack with the printable side facedown.

Without an optional staple finisher With an optional staple finisher
Using MS810de 96


Without an optional staple finisher With an optional staple finisher


Using MS810de 97


Using MS810de 98


6 For custom‑ or Universal‑size paper, adjust the paper guides to lightly touch the sides of the stack, and then lock the length guide.
7 Insert the tray.
8 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Using MS810de 99

1 Pull out the tray.
2 Adjust the width and length guides.
Loading A5‑size paper
a Pull up and slide the width guide to the position for A5.

Using MS810de 100

b Squeeze and slide the length guide to the position for A5 until it clicks into place.

c Remove the A5 length guide from its holder.
d Insert the A5 length guide into its designated slot.
Using MS810de 101

Loading A4‑, letter‑, legal‑, Oficio‑, and Folio‑size paper
a Pull up and slide the width guide to the correct position for the size of the paper being loaded.

Using MS810de 102

b If the A5 length guide is still attached to the length guide, then remove it from its place. If the A5 length
guide is not attached, then proceed to step d.
c Put the A5 length guide in its holder.
Using MS810de 103

d Squeeze the length guide and slide it to the correct position for the size of the paper being loaded until
it clicks into place.

3 Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load the paper stack with the printable side facedown.
Using MS810de 104


Without an optional staple finisher With an optional staple finisher

Using MS810de 105

5 Insert the tray.
Using MS810de 106

6 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
1 Pull down the multipurpose feeder door.

LTR
B5
EXEC
Using MS810de 107

2 Pull the multipurpose feeder extender.
LTR
B5
EXEC
3 Slide the width guide to the correct position for the size of the paper being loaded.
A4 A5
EXEC
B5
Using MS810de 108


B5
4 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper or specialty media.
Using MS810de 109

Without an optional staple finisher With an optional staple finisher
ABC
One‑sided printing
One‑sided printing
Two‑sided printing
Two‑sided printing
One‑sided printing Two‑sided printing
Using MS810de 110

LTR
B5
EXEC
6 For custom- or Universal-size paper, adjust the width guides to lightly touch the sides of the stack.
7 From the Paper menu on the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Using MS810de 111

1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
Using the printer control panel
1 From the home screen, navigate to:
> Paper Menu > Custom Names
2 Select a custom name, and then type a custom paper type name.
Using MS810de 112

4 Touch Custom Types, and then verify that the new custom paper type name has replaced the custom name.
Using the Embedded Web Server
Assign a custom paper type name to a tray when linking or unlinking trays.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type
4 Click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Paper Menu > Custom Types
2 Select a custom paper type name, and then select a paper type
1 From the document that you are trying to print, open the Print dialog.
2 If necessary, adjust the settings.
3 Print the document.
Using MS810de 113 · 3 Touch · 3 Touch

1 From the home screen, navigate to:
Forms and Favorites > select form > Print
2 If necessary, configure the print settings.
3 Send the print job.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the setting, and then click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Settings > Print Settings > Quality Menu > Toner Darkness
2 Adjust the setting, and then touch
Using MS810de 114

1 Insert a flash drive into the USB port.

Using MS810de 115

2 From the printer control panel, touch the document you want to print.
3 Touch the arrows to specify the number of copies for printing, and then touch Print.
Recommended flash drives File type
Documents:
Images:
Using MS810de 116

Mopria® Print Service is a mobile printing solution for mobile devices running on Android version 4.4 or later. It allows you to print directly to any Mopria‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Tap Print, and then select the printer.
3 Send the print job.
Google Cloud Print is a mobile printing service that allows enabled applications on mobile devices to print to any Google Cloud Print‑ready printer.
1 From the home screen of your mobile device, launch an enabled application.
2 Tap Print, and then select the printer.
3 Send the print job.
AirPrint is a mobile printing solution that allows you to print directly from Apple devices to an AirPrint‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Select an item to print, and then tap the share icon.
3 Tap Print, and then select the printer.
4 Send the print job.
Lexmark Print allows you to send documents and images directly to a Lexmark device.
1 Open the document, and then send or share the document to Lexmark Print.
2 Select a device.
3 Print the document.
Using MS810de 117

1 From the home screen, navigate to:
> Security > Confidential Print > select a print job type
Max Invalid PIN Limit the number of times an invalid PIN can be entered.
Confidential Job Expiration Hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Print and store print jobs in the printer memory.
Verify Job Expiration Print one copy of a print job and hold the remaining copies. It lets you examine if the first copy is satisfactory or not. The print job is automatically deleted from the printer memory when all copies are printed.
Reserve Job Expiration Store print jobs for printing at a later time.
1 From the document that you are trying to print, open the Print dialog.
3 Select the print job type.
4 If necessary, assign a user name.
5 Send the print job.
6 From the printer home screen, touch Held Jobs.
7 Send the print job.
Using MS810de 118 · Use To · 2 Touch

1 From the home screen, navigate to:
> Reports > Print Fonts
2 Touch PCL Fonts or PostScript Fonts.
A directory list shows the resources stored in a flash memory or in the printer hard disk.
From the home screen, navigate to:
> Reports > Print Directory
1 From the home screen, touch Cancel Jobs, or press on the keypad.
2 Touch the job you want to cancel, and then touch
3 Press on the keypad to return to the home screen.
For Windows users
1 Open the printers folder, and then select your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
1 From System Preferences in the Apple menu, navigate to your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
Using MS810de 119

This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Check the virtual display that appears at the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e‑mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Using MS810de 120 · Notification Description

Continuable Stop1 The printer stops processing jobs when the supply condition is reached, and the user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops processing jobs when the supply condition is reached. The supply
must be replaced to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Confidential Print Setup.
4 Click Submit to save the modified settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Copy Printer Settings.
3 To change the language, select a language from the drop‑down menu, and then click Click here to submit language.
4 Click Printer Settings.
Using MS810de 121 · Notification Description

5 Type the IP addresses of the source and target printers.
6 Click Copy Printer Settings.
From the home screen, navigate to:
> Reports > Menu Settings Page
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the home screen, navigate to:
> Reports > Network Setup Page
2 Check the first section of the network setup page and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult your system support person for a solution, and then print another network setup page.
From the home screen, touch Status/Supplies > View Supplies.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.
Using MS810de 122

Using Eco‑Mode
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Eco‑Mode.
3 Select a setting.
Off Use the factory default settings for all settings associated with Eco‑Mode.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
Plain Paper Enable the automatic two‑sided (duplex) printing feature.
4 Click Submit.
Enable Quiet mode to reduce printer noise.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Quiet Mode.
3 Select a setting.
Using MS810de 123 · Use To

On Reduce printer noise.
Off Use factory default settings.
4 Click Submit.
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts > Sleep Mode
2 In the Sleep Mode field, select the number of minutes the printer is idle before it enters Sleep mode.
3 Apply the changes.
Hibernate is an ultra‑low‑power saving mode.
1 From the home screen, navigate to:
> Settings > General Settings
2 Touch Press Sleep Button or Press and Hold Sleep Button.
3 Touch Hibernate >
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 122.
Using MS810de 124 · Use To

If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 127.
From the home screen, navigate to:
> Settings > General Settings > Factory Defaults > Restore Now >
The printer is equipped with a security lock feature. When a lock compatible with most laptop computers is attached, the printer is locked. When locked, the controller board shield and the controller board cannot be removed. Attach a security lock to the printer in the location shown.
Your printer contains various types of memory that can store device and network settings, and user data.
Using MS810de 125

Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, device settings, network information, bookmark settings, and embedded solutions.
Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for device-specific functionality. This lets the device retain buffered user data from complex print jobs, as well as form data, and font data.
Erase the content of any installed printer memory in the following circumstances:
Disposing of a printer hard disk
In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, simply turn off the printer.
Using MS810de 126

Erasing non‑volatile memory
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 on the keypad while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display instead of the standard home screen icons.
3 Touch Wipe All Settings.
The printer will restart several times during this process.
4 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Using the printer control panel
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, the touch screen displays a list of functions.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Using MS810de 127

Enable hard disk encryption to prevent loss of sensitive data in the event the printer or its hard disk is stolen.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Disk Encryption.
3 From the Disk encryption menu, select Enable.
4 Click Submit.
Using the printer control panel
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Touch Disk Encryption > Enable.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Using MS810de 128

In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.
Using MS810de 129

Learning about the printer


2 Printer control panel
4 Standard 550‑sheet tray (Tray 1)
Using MS812de 130 · 1 Standard bin · 3 Multipurpose feeder

The following illustration shows the maximum number of optional finishers and trays that are supported by the printer. For more information on other configurations, visit www.lexmark.com/multifunctionprinters.


Hardware option Alternative hardware option
3 Caster base None
4 2100‑sheet tray None
5 550‑sheet tray 250‑sheet tray
6 250‑sheet tray 550‑sheet tray
7 4‑bin mailbox Output expander
8 Output expander 4‑bin mailbox
Using MS812de 131

The staple, hole punch finisher must not be combined with any other output options.


3 Sleep button Enable Sleep mode or Hibernate mode.
Do the following to wake the printer from Sleep mode:
4 Keypad Enter numbers, letters, or symbols on the printer.
5 Stop or Cancel button Stop all printer activity.
6 Indicator light Check the status of the printer.
Using MS812de 132

7 USB port Connect a USB Bluetooth adapter or a flash drive to the printer.
The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition.
Indicator light Printer status
Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Solid green The printer is on, but idle.
Blinking red The printer requires user intervention.
Sleep button light Printer status
Off The printer is off, idle or in Ready state.
Solid amber The printer is in Sleep mode.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern
The printer is in Hibernate mode.
When the printer is turned on, the display shows a basic screen, referred to as the home screen. Use the home screen buttons and icons to initiate an action.
1 2 3 4

5 6 7 8
Using MS812de 133 · Use the To

1 Search Held Jobs Search current held jobs.
2 Held Jobs Display all current held jobs.
3 Forms and Favorites Access frequently used online forms.
4 Eco‑Settings Adjust energy consumption, noise, toner and paper usage.
5 Menus Access printer menus.
8 Tips Open a context‑sensitive Help information on the printer control panel.
If an attendance message affects a function, then this icon appears and the red indicator light blinks.
The IP address of your network printer is located at the top left corner of the home screen and appears as four sets of numbers separated by periods. You can use the IP address when accessing the Embedded Web Server so you can view and remotely configure printer settings even when you are not physically near the printer.


4 5 6 7 8
Scroll to the left.
Scroll to the right.
Scroll up.
Scroll down.
5 Submit Submit changes made in the printer settings.
6 Back Return to the previous screen.
Return to the home screen.
Open a context-sensitive Help dialog on the printer control panel.

Save settings.
Select a higher value.
Select a lower value.
Leave the current screen.
Search current held jobs.

1 In the Run dialog box, type cmd to open the command prompt.
2 Type ipconfig, and then look for the IP address.
1 From System Preferences in the Apple menu, select Network.
2 Select your connection type, and then click Advanced > TCP/IP.
3 Look for the IP address.
You can find the printer IP address:
The Embedded Web Server is the printer Web page that lets you view and remotely configure printer settings even when you are not physically near the printer.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
Using MS812de 137

1 Open a Web browser, and then type the printer IP address in the address field.
2 Do one or more of the following: • Show or hide icons of basic printer functions. a Click Settings > General Settings > Home screen customization. b Select the check boxes to specify which icons appear on the printer home screen.
Your printer comes with preinstalled home screen applications. Before you can use these applications, you must first activate and set up these applications using the Embedded Web Server. For more information on accessing the Embedded Web Server, see “Accessing the Embedded Web Server” on page 89.
For more information on configuring and using the home screen applications, do the following:
1 Go to http://support.lexmark.com.
3 Click the Manuals tab, and then select the document for the home screen application.
Customize the background and idle screen of your printer home screen.
From the home screen, navigate to:
Change Background > select background to use > Apply
Using MS812de 138 · Use To

Quickly find and print frequently used online forms directly from the printer home screen.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Apps > Apps Management > Forms and Favorites.
3 Click Add, and then customize the settings.
4 Click Apply.
To use the application, touch Forms and Favorites on the printer home screen, and then navigate through form categories, or search for forms based on a form number, name, or description.
Understanding Eco‑Settings
Manage energy consumption, noise, toner, and paper usage settings to help reduce the environmental impact of your printer.
Using MS812de 139 · Use To · Use To

You can export configuration settings into a text file, and then import the file to apply the settings to other printers.
1 Open a Web browser, and then type the printer IP address in the address field.
2 To export or import a configuration for one application, do the following: a Click Settings > Apps > Apps Management. b From the list of installed applications, click the name of the application you want to configure.
c Click Configure, and then do either of the following:
– When saving the configuration file, you can type a unique file name or use the default name. – If a "JVM Out of Memory” error occurs, then repeat the export process until the configuration
file is saved. • To import a configuration from a file, click Import, and then browse to the saved configuration file that was exported from a previously configured printer.
– Before importing the configuration file, you can choose to preview it first or load it directly. – If a timeout occurs and a blank screen appears, then refresh the Web browser, and then click
Apply.
3 To export or import a configuration for multiple applications, do the following: a Click Settings > Import/Export. b Do either of the following:
This application enables you to interact with the printer control panel even when you are not physically near the network printer. From your computer, you can view the printer status, release held print jobs, create bookmarks, and do other print-related tasks.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Remote Operator Panel Settings.
Using MS812de 140

3 Select the Enable check box, and then customize the settings.
4 Click Submit.
To use the application, click Remote Operator Panel > Launch VNC Applet.
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 263 and “Storing paper” on page 182.
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select a paper size or type > Submit
Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select a unit of measure
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch Submit.
Using MS812de 141

1 Pull out the tray.

Using MS812de 142

2 Squeeze and slide the width guide to the correct position for the size of the paper being loaded until it clicks into place.


Using MS812de 143

3 Unlock the length guide, and then squeeze and slide the guide to the correct position for the size of the paper being loaded.


Using MS812de 144

4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack with the printable side facedown.

Without an optional staple finisher With an optional staple finisher

Using MS812de 145


Using MS812de 146


Using MS812de 147


6 For custom‑ or Universal‑size paper, adjust the paper guides to lightly touch the sides of the stack, and then lock the length guide.
7 Insert the tray.
8 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Using MS812de 148

1 Pull out the tray.
2 Adjust the width and length guides.
Loading A5‑size paper
a Pull up and slide the width guide to the position for A5.

Using MS812de 149

b Squeeze and slide the length guide to the position for A5 until it clicks into place.

c Remove the A5 length guide from its holder.
d Insert the A5 length guide into its designated slot.
Using MS812de 150

Loading A4‑, letter‑, legal‑, oficio‑, and folio‑size paper
a Pull up and slide the width guide to the correct position for the size of the paper being loaded.

Using MS812de 151

b If the A5 length guide is still attached to the length guide, then remove it from its place. If the A5 length
guide is not attached, then proceed to step d.
c Put the A5 length guide in its holder.
Using MS812de 152

d Squeeze the length guide and slide it to the correct position for the size of the paper being loaded until
it clicks into place.

3 Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

4 Load the paper stack with the printable side facedown.
Using MS812de 153


Without an optional staple finisher With an optional staple finisher

Using MS812de 154

5 Insert the tray.
Using MS812de 155

6 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded.
1 Pull down the multipurpose feeder door.

EXEC
A4 A5
LTR
Using MS812de 156

2 Using the handle, pull the multipurpose feeder extender.
LTR
B5
EXEC
3 Slide the width guide to the correct position for the size of the paper being loaded.
A4 A5
EXEC
B5
Using MS812de 157


B5
4 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper or specialty media.
Using MS812de 158

Without an optional staple finisher With an optional staple finisher
ABC
One‑sided printing
One‑sided printing
Two‑sided printing
Two‑sided printing
One‑sided printing Two‑sided printing
Using MS812de 159

LTR
B5
EXEC
6 For custom- or Universal-size paper, adjust the width guides to lightly touch the sides of the stack.
7 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Using MS812de 160

1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu.
4 Click Submit.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
Using the printer control panel
1 From the home screen, navigate to:
> Paper Menu > Custom Names
2 Select a custom name, and then type a custom paper type name.
3 Touch Submit.
4 Touch Custom Types, and then verify if the new custom paper type name has replaced the custom name.
Using MS812de 161

Using the Embedded Web Server
Assign a custom paper type name to a tray when linking or unlinking trays.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type.
4 Click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Paper Menu > Custom Types
2 Select a custom paper type name, and then select a paper type.
3 Touch Submit.
1 From the document that you are trying to print, open the Print dialog.
2 If necessary, adjust the settings.
3 Send the print job.
1 From the home screen, navigate to:
Forms and Favorites > select form > Print
2 If necessary, configure the print settings.
Using MS812de 162

3 Send the print job.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness, and then click Submit.
Using the printer control panel
1 From the home screen, navigate to:
> Settings > Print Settings > Quality Menu > Toner Darkness
2 Adjust the setting, and then touch Submit.
1 Insert a flash drive into the USB port.
Using MS812de 163

2 From the printer control panel, touch the document you want to print.
3 Touch the arrows to specify the number of copies for printing, and then touch Print.
Using MS812de 164

Recommended flash drives File type
Documents:
Images:
Mopria® Print Service is a mobile printing solution for mobile devices running on Android version 4.4 or later. It allows you to print directly to any Mopria‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Tap Print, and then select the printer.
3 Send the print job.
Google Cloud Print is a mobile printing service that allows enabled applications on mobile devices to print to any Google Cloud Print‑ready printer.
1 From the home screen of your mobile device, launch an enabled application.
2 Tap Print, and then select the printer.
3 Send the print job.
AirPrint is a mobile printing solution that allows you to print directly from Apple devices to an AirPrint‑certified printer.
Using MS812de 165

1 From the home screen of your mobile device, launch a compatible application.
2 Select an item to print, and then tap the share icon.
3 Tap Print, and then select the printer.
4 Send the print job.
Lexmark Print allows you to send documents and images directly to a Lexmark device.
1 Open the document, and then send or share the document to Lexmark Print.
2 Select a device.
3 Print the document.
1 From the printer control panel, navigate to:
> Security > Confidential Print > select the print job type
Max Invalid PIN Limit the number of times an invalid PIN can be entered.
Confidential Job Expiration Hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Print and store print jobs in the printer memory.
Verify Job Expiration Print one copy of a print job and hold the remaining copies. It allows you to examine if the first copy is satisfactory. The print job is automatically deleted from the printer memory when all copies are printed.
Reserve Job Expiration Store print jobs for printing at a later time.
Using MS812de 166 · Use To

2 Touch Submit.
1 From the document you are trying to print, open the Print dialog.
3 Select the print job type.
4 If necessary, assign a user name.
5 Send the print job.
6 From the printer home screen, touch Held Jobs.
7 Send the print job.
1 From the home screen, navigate to:
> Reports > Print Fonts
2 Touch PCL Fonts or PostScript Fonts.
A directory list shows the resources stored in a flash memory or in the printer hard disk.
From the home screen, navigate to:
> Reports > Print Directory
Using MS812de 167 · Use To

1 From the printer control panel, touch Cancel Job or press
on the keypad.
2 Touch the print job you want to cancel, and then touch Delete Selected Jobs.
on the keypad, then touch Resume to return to the home screen.
For Windows users
1 Open the printers folder, and then select your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
1 From System Preferences in the Apple menu, navigate to your printer.
2 From the print queue, select the print job you want to cancel, and then delete it.
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Check the virtual display that appears in the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
Using MS812de 168

1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e-mail when the supply condition is reached. The status of the supply will appear on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached, and the user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops when the supply condition is reached. The supply must be replaced
to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Confidential Print Setup.
Using MS812de 169 · Notification Description

4 Click Submit to save the modified settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Copy Printer Settings.
3 To change the language, select a language from the drop‑down menu, and then click Click here to submit language.
4 Click Printer Settings.
5 Type the IP addresses of the source and target printers.
6 Click Copy Printer Settings.
From the home screen, navigate to:
> Reports > Menu Settings Page
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the home screen, navigate to:
> Reports > Network Setup Page
2 Check the first section of the network setup page and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult your system support person for a solution, and then print another network setup page.
Using MS812de 170

A message appears on the printer display when a replacement supply item is needed or when maintenance is required.
From the home screen, navigate to:
Status/Supplies > View Supplies
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Device Status > More Details.
Using Eco‑Mode
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Eco‑Mode.
3 Select a setting.
Using MS812de 171

Off Use the factory default settings for all settings associated with Eco‑Mode.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
Plain Paper Enable the automatic two‑sided (duplex) printing feature.
4 Click Submit.
Enable Quiet mode to reduce printer noise.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Quiet Mode.
3 Select a setting.
Using MS812de 172 · Use To

On Reduce printer noise.
Off Use factory default settings.
4 Click Submit.
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts > Sleep Mode
2 In the Sleep Mode field, select the number of minutes the printer is idle before it enters Sleep mode.
3 Apply the changes.
Hibernate is an ultra‑low‑power operating mode.
1 From the home screen, navigate to:
> Settings > General Settings
2 From the “Press Sleep Button” or “Press and Hold Sleep Button” menu, select Hibernate, and then touch Submit.
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 170.
Using MS812de 173 · Use To

If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 175.
From the home screen, navigate to:
> Settings > General Settings > Factory Defaults > Restore Now > Submit
The printer is equipped with a security lock feature. When a lock compatible with most laptop computers is attached, the printer is locked. When locked, the controller board shield and the controller board cannot be removed. Attach a security lock to the printer in the location shown.
Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store the operating system, device settings, network information, bookmark settings, and embedded solutions.
Using MS812de 174

Type of memory Description
Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for device-specific functionality. This lets the device retain buffered user data from complex print jobs, as well as form data, and font data.
Erase the content of any installed printer memory in the following circumstances:
Disposing of a printer hard disk
In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, simply turn off the printer.
Erasing non‑volatile memory
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display, instead of the standard home screen icons.
3 Touch Wipe All Settings.
The printer restarts several times during this process.
4 Touch Back > Exit Config Menu.
Using MS812de 175

The printer will perform a power‑on reset, and then return to normal operating mode.
Using the printer control panel
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, the touch screen displays a list of functions.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
Enable hard disk encryption to prevent loss of sensitive data in the event the printer or its hard disk is stolen.
Using the Embedded Web Server
1 Open a Web browser, and then type the printer IP address in the address field.
Using MS812de 176

2 Click Settings > Security > Disk Encryption.
3 From the Disk encryption menu, select Enable.
4 Click Submit.
Using the printer control panel
1 Turn off the printer.
2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Touch Disk Encryption > Enable.
4 Touch Yes to proceed with disk wiping.
5 Touch Back > Exit Config Menu.
The printer will perform a power‑on reset, and then return to normal operating mode.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.
Using MS812de 177

Paper and specialty media guide 178
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly affect print quality.

Paper and specialty media guide 179

Paper and specialty media guide 180
Selecting the correct paper or specialty media reduces printing problems. For the best print quality, try a sample of the paper or specialty media before buying large quantities.
The following paper characteristics affect print quality and reliability. Consider these factors before printing on them:
The printer trays and multipurpose feeder can automatically feed paper weights between 60–176 g/m2 (16– 47‑lb) grain long paper. The 2100‑sheet tray can automatically feed paper weights up to 60–135 g/m2 (16–36‑lb) grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, and may cause jams.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, toner cannot fuse to it properly. If paper is too smooth, it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; smoothness between 150 and 250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–176 g/m2 (16–47‑lb) paper, grain long paper is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability, resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.

Paper and specialty media guide 181
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid paper jams and poor print quality:
As an environmentally conscientious company, Lexmark supports the use of recycled paper produced specifically for use in laser (electrophotographic) printers.
While no blanket statement can be made that all recycled paper will feed well, Lexmark consistently tests papers that represent recycled cut size copier papers available on the global market. This scientific testing is conducted with rigor and discipline. Many factors are taken into consideration both separately and as a whole, including the following:
Recycled papers are better than ever; however, the amount of recycled content in a paper affects the degree of control over foreign matter. And while recycled papers are one good path to printing in an environmentally responsible manner, they are not perfect. The energy required to de-ink and deal with additives such as colorants and “glue” often generates more carbon emissions than does normal paper production. However, using recycled papers enables better resource management overall.

Paper and specialty media guide 182
Lexmark concerns itself with the responsible use of paper in general based on life cycle assessments of its products. To gain a better understanding of the impact of printers on the environment, the company commissioned a number of life cycle assessments and found that paper was identified as the primary contributor (up to 80%) of carbon emissions caused throughout the entire life of a device (from design to end-of-life). This is due to the energy-intensive manufacturing processes required to make paper.
Thus, Lexmark seeks to educate customers and partners on minimizing the impact of paper. Using recycled paper is one way. Eliminating excessive and unnecessary paper consumption is another. Lexmark is well- equipped to help customers minimize printing and copying waste. In addition, the company encourages purchasing paper from suppliers who demonstrate their commitment to sustainable forestry practices.
Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained. However, the following paper choice guidelines will help alleviate the environmental impact of printing:
1 Minimize paper consumption.
2 Be selective about the origin of wood fiber. Buy from suppliers who carry certifications such as the Forestry Stewardship Council (FSC) or The Program for the Endorsement of Forest Certification (PEFC). These certifications guarantee that the paper manufacturer uses wood pulp from forestry operators that employ environmentally and socially responsible forest management and restoration practices.
3 Choose the most appropriate paper for printing needs: normal 75 or 80 g/m2 certified paper, lower weight paper, or recycled paper.
Test results indicate that the following paper types are at risk for use with laser printers:
For more information about Lexmark, visit www.lexmark.com. General sustainability-related information can be found at the Environmental Sustainability link.
Use these paper storage guidelines to help avoid jams and uneven print quality:

Paper and specialty media guide 183
The following tables provide information on standard and optional paper sources and the sizes, types, and weights of paper they support.
The printer engine supports 60–176‑g/m2 (16–47‑lb) paper weights.

Paper type 250‑ or 550‑sheet trays
* Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 179.

Paper and specialty media guide 184
Paper size1 Dimensions Standard or optional 250‑ or 550‑sheet tray
Optional 2100‑sheet tray Multipurpose feeder
A4 210 x 297 mm (8.3 x 11.7 in.)
A5 148 x 210 mm (5.8 x 8.3 in.)
A6 105 x 148 mm (4.1 x 5.8 in.)
JIS B5 182 x 257 mm (7.2 x 10.1 in.)
Letter 216 x 279 mm (8.5 x 11 in.)
Legal 216 x 356 mm (8.5 x 14 in.)
Executive 184 x 267 mm (7.3 x 10.5 in.)
Oficio 216 x 340 mm (8.5 x 13.4 in.)
Folio 216 x 330 mm (8.5 x 13 in.)
Statement 140 x 216 mm (5.5 x 8.5 in.)
Universal3 105 x 148 mm to 216 x 356 mm (4.13 x 5.83 in. to 8.5 x 14 in.)
70 x 127 mm to 216 x 356 mm (2.76 x 5 to 8.5 x 14 in.)
7 3/4 Envelope (Monarch)
98 x 191 mm (3.9 x 7.5 in.)
9 Envelope 98 x 225 mm (3.9 x 8.9 in.)
1 If your preferred default paper size cannot be set in the printer control panel, then you may select common paper sizes that correspond to the position of the length guide in the tray from the Paper Size/Type menu. If the paper size is not available, then select Universal or turn off tray size sensing. For more information, contact customer support.
2 Paper is supported in long‑edge orientation.
3 Universal is supported in duplex mode only if the width is from 105 mm (4.13 in.) to 216 mm (8.5 in.), and the length is from 148 mm (5.83 in.) to 356 mm (14 in.).
Duplex

Paper and specialty media guide 185
Paper size1 Dimensions Standard or optional 250‑ or 550‑sheet tray
Optional 2100‑sheet tray Multipurpose feeder
10 Envelope 105 x 241 mm (4.1 x 9.5 in.)
DL Envelope 110 x 220 mm (4.3 x 8.7 in.)
C5 Envelope 162 x 229 mm (6.38 x 9.01 in.)
B5 Envelope 176 x 250 mm (6.93 x 9.84 in.)
Other Envelope 98 x 162 mm (3.9 x 6.4 in.) to 176 x 250 mm (6.9 x 9.8 in.)
1 If your preferred default paper size cannot be set in the printer control panel, then you may select common paper sizes that correspond to the position of the length guide in the tray from the Paper Size/Type menu. If the paper size is not available, then select Universal or turn off tray size sensing. For more information, contact customer support.
2 Paper is supported in long‑edge orientation.
3 Universal is supported in duplex mode only if the width is from 105 mm (4.13 in.) to 216 mm (8.5 in.), and the length is from 148 mm (5.83 in.) to 356 mm (14 in.).

Paper size 4‑bin mailbox Output expander and high‑capacity
1 The finisher staples the paper if it is loaded long edge first.
2 The finisher stacks the paper but does not staple or punch holes in it.
3 The finisher stacks and staples the paper but does not punch holes in it.
4 The finisher staples the paper if its width is from 210 mm (8.27 in.) to 217 mm (8.54 in.).
Duplex

Paper and specialty media guide 186

Paper size 4‑bin mailbox Output expander and high‑capacity
1 The finisher staples the paper if it is loaded long edge first.
2 The finisher stacks the paper but does not staple or punch holes in it.
3 The finisher stacks and staples the paper but does not punch holes in it.
4 The finisher staples the paper if its width is from 210 mm (8.27 in.) to 217 mm (8.54 in.).

Paper type Paper weight 4‑bin mailbox Output expander and
1 The finisher stacks the paper but does not staple or punch holes in it.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 179.

Paper and specialty media guide 187

Paper type Paper weight 4‑bin mailbox Output expander and
1 The finisher stacks the paper but does not staple or punch holes in it.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 179.

Paper and specialty media guide 188
Paper type Paper weight 4‑bin mailbox Output expander and
Staple finisher Staple, hole punch finisher
high‑capacity output expander
Rough/cotton 90–176 g/m2
(24–47 lb bond) X X X
Custom type [x] 90–176 g/m2
(24–47 lb bond) X X X
1 The finisher stacks the paper but does not staple or punch holes in it.
2 Print on transparencies by batches of only up to 20 to prevent them from sticking together. For more information, see “Tips on using transparencies” on page 179.

Understanding the printer menus 189
Menus list
Paper Menu Reports Network/Ports
Configure MP Substitute Size
Network Setup Page1
Parallel [x] Serial [x]
Custom Bin Names3
Security Settings Help Option Card Menu5
Edit Security Setups4
A list of installed DLEs (Download Emulators) appears.
Flash Drive Menu Print Settings
Print Quality Printing Guide
Miscellaneous Security Settings3
Erase Temporary Data Files
Information Guide Supplies Guide
Security Audit Log Set Date and Time
1 Depending on the printer setup, this menu item appears as Network Setup Page or Network [x] Setup Page.
2 Depending on the printer setup, this menu item appears as Standard Network or Network [x].
3 This menu appears only in touch‑screen printer models.
4 This menu appears only in some touch‑screen printer models.
5 This menu appears only when one or more DLEs are installed.

Understanding the printer menus 190
Vinyl label is supported only in MS710 Series printer models.
Set a default paper source for all print jobs.
Tray [x] Multipurpose Feeder1
Manual Paper Manual Envelope
1 This menu appears only in touch‑screen printer models.
2 This menu appears only in non‑touch‑screen printer models.
Specify the paper size loaded in each tray.
A4 A5 A6 JIS‑B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope

Understanding the printer menus 191
Specify the paper type loaded in each tray.
Plain Paper Card Stock Transparency Recycled Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the paper size loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Use To · Tray [x] Type · MP Feeder Size

Understanding the printer menus 192
Specify the paper type loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the paper size being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the paper type being manually loaded.
Plain Paper Card Stock Transparency Recycled Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]

Understanding the printer menus 193
Specify the envelope size being manually loaded.
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the envelope type being manually loaded.
Envelope Rough Envelope Custom Type [x]
Determine when the printer selects paper from the multipurpose feeder.
Substitute a specified paper size if the requested paper size is not available.
Off Statement/A5 Letter/A4 All Listed

Understanding the printer menus 194
Specify the relative texture of the plain paper loaded in a specific tray.
Specify the relative texture of the card stock loaded in a specific tray.
Specify the relative texture of the transparencies loaded in a specific tray.
Specify the relative texture of the recycled paper loaded in a specific tray.
Specify the relative texture of the labels loaded in a specific tray.
Specify the relative texture of the vinyl labels loaded in a specific tray.
Specify the relative texture of the bond paper loaded in a specific tray.
Specify the relative texture of the envelopes loaded in a specific tray.
Specify the relative texture of the rough envelopes loaded in a specific tray.
Specify the relative texture of the letterhead loaded in a specific tray.

Understanding the printer menus 195
Specify the relative texture of the preprinted paper loaded in a specific tray.
Specify the relative texture of the colored paper loaded in a specific tray.
Specify the relative texture of the light paper loaded in a specific tray.
Specify the relative texture of the heavy paper loaded in a specific tray.
Specify the relative texture of the rough or cotton paper loaded in a specific tray.
Specify the relative texture of the custom paper loaded in a specific tray.
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.
Specify the relative weight of the transparencies loaded.
Specify the relative weight of the recycled paper loaded.

Understanding the printer menus 196
Specify the relative weight of the labels loaded.
Specify the relative weight of the vinyl labels loaded.
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the envelope loaded.
Specify the relative weight of the rough envelope loaded.
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.
Specify the relative weight of the colored paper loaded.
Specify that the weight of the paper loaded is light.
Specify that the weight of the paper loaded is heavy.
Specify the relative weight of the cotton or rough paper loaded.

Understanding the printer menus 197
Specify the relative weight of the custom paper loaded.
Determine and set two-sided printing for all print jobs with Card Stock as the paper type.
Determine and set two-sided printing for all print jobs with Recycled as the paper type.
Determine and set two-sided printing for all print jobs with Labels as the paper type.
Determine and set two-sided printing for all print jobs with Vinyl Labels as the paper type.
Determine and set two-sided printing for all print jobs with Bond as the paper type.
Determine and set two-sided printing for all print jobs with Letterhead as the paper type.
Determine and set two-sided printing for all print jobs with Preprinted as the paper type.
Determine and set two-sided printing for all print jobs with Colored as the paper type.
Determine and set two-sided printing for all print jobs with Light as the paper type.

Understanding the printer menus 198
Determine and set two-sided printing for all print jobs with Heavy as the paper type.
Determine and set two-sided printing for all print jobs with Rough or Cotton as the paper type.
Determine and set two-sided printing for all print jobs with Custom [x] as the paper type.
Associate a paper or specialty media type with a factory default custom type name or a user‑defined custom name created from the Embedded Web Server or from MarkVisionTM Professional.
Paper Card Stock Transparency Rough/Cotton Labels Vinyl Labels Envelope
Specify a paper type when Recycled is selected in other menus.
Paper Card Stock Transparency Rough/Cotton Labels Vinyl Labels Envelope
Custom Name [x] Specify a custom name for a paper type. This name replaces the Custom Type [x] name in the printer menus.

Understanding the printer menus 199
Standard Bin Specify a custom name for the standard bin.
Bin [x] Specify a custom name for Bin [x].
Identify the units of measure.
Set the portrait width.
3–14.17 inches 76–360 mm
Set the portrait height.
3–14.17 inches 76–360 mm
Specify the feed direction if the paper can be loaded in either direction.
Short Edge Long Edge

Understanding the printer menus 200
Specify the default bin.
Standard Bin Bin [x]
Specify configuration options for bins.
Mailbox Link Mail Overflow Link Optional Type Assignment
Specify an alternative bin when a designated bin is full.
Standard Bin Bin [x]

Understanding the printer menus 201
Select a bin for each supported paper type.
Plain Paper Bin Card Stock Bin Transparency Bin Recycled Bin Labels Bin Vinyl Labels Bin Bond Bin Envelope Bin Rough Envelope Bin Letterhead Bin Preprinted Bin Colored Bin Light Paper Bin Heavy Paper Bin Rough/Cotton Bin Custom [x] Bin
For each type, select the following options:
Disabled Standard Bin Bin [x]
Menu Settings Page Print a report containing information about the paper loaded in trays, installed memory, total page count, alarms, timeouts, printer control panel language, TCP/IP address, status of supplies, status of the network connection, and other information.
Device Statistics Print a report containing printer statistics such as supply information and details about printed pages.
Stapler Test Print a report that confirms that the staple finisher is functioning properly.
Network Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address information.
Network [x] Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address information.
Use To · Assign Type/Bin · Use To
![Page 202 of the Lexmark MS811 user manual — Standard Network or Network [x] menu](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-202.webp?w=400)
Understanding the printer menus 202
Profiles List Print a list of profiles stored in the printer.
Print a report of all the fonts available for the printer language currently set in the printer.
PCL Fonts PostScript Fonts
Print Directory Print a list of all the resources stored in an optional flash memory card or printer hard disk.
Asset Report Print a report containing printer asset information, such as serial number and model name.
Allow the printer to connect to a network.
Auto [list of available network cards]
Reduce power consumption when the printer receives no data from the Ethernet network.

Understanding the printer menus 203
Set the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the network input buffer.
Auto 3KB to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing. This menu only appears when a formatted disk is installed.
Set the printer to process Macintosh binary PostScript print jobs.

Understanding the printer menus 204
Standard Network Setup OR Network [x] Setup
Show and set the printer network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
To access the menu, navigate to either of the following:
Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP
address.
To access the menu, navigate to either of the following:
View the connection status of the wireless network adapter.
View Card Speed View the speed of an active wireless network adapter.
View the network addresses.
Set the amount of time it takes for a network print job to be canceled.
Allow the printer to print a banner page.

Understanding the printer menus 205
To access the menu, navigate to either of the following:
Set Hostname Set the current TCP/IP host name.
IP Address View or change the current TCP/IP address.
Netmask View or change the current TCP/IP netmask.
Gateway View or change the current TCP/IP gateway.
Specify the DHCP address and parameter assignment.
Specify the RARP address assignment setting.
Specify the BOOTP address assignment setting.
Specify the Zero Configuration Networking setting.
Enable the built-in FTP server, which lets you send files to the printer using File Transfer Protocol.
Enable the built-in Web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a Web browser.
WINS Server Address View or change the current WINS server address.
View or change the current DDNS setting.
View or change the current mDNS setting.
DNS Server Address View or change the current DNS server address.

Understanding the printer menus 206
Backup DNS Server Address View or change the backup DNS server addresses.
Backup DNS Server Address 2
Backup DNS Server Address 3
View or change the current HTTPS setting.
To access the menu, navigate to any of the following:
Enable IPv6 in the printer.
Specify whether or not the network adapter accepts the automatic IPv6 address configuration entries provided by a router.
Set Hostname Set the host name.
Enable DHCPv6 in the printer.
To access the menu, navigate to:
Network/Ports > Network [x] > Network [x] Setup > Wireless

Understanding the printer menus 207
Wi‑Fi Protected Setup
Establish a wireless network and enable network security.
Start Push Button Method Start PIN Method
Enable/Disable WPS Auto‑detection
Automatically detect the connection method that an access point with WPS uses—Start Push Button Method or Start PIN Method.
Network Mode BSS Type
Specify the network mode.
Specify the wireless standard for the wireless network.
802.11b/g 802.11b/g/n
Choose Network Select an available network for the printer to use.
View Signal Quality View the quality of the wireless connection.
View Security Mode View the encryption method for the wireless network.
To access the menu, navigate to either of the following:
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.
View Address Show the assigned AppleTalk address.

Understanding the printer menus 208
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]
Set the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
![Page 209 of the Lexmark MS811 user manual — Parallel [x] menu](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-209.webp?w=400)
Understanding the printer menus 209
Set the size of the USB input buffer.
Disabled Auto 3K to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing.
Set the printer to process Macintosh binary PostScript print jobs.
Set the network address information for an external print server.
yyy.yyy.yyy.yyy
Set the netmask information for an external print server.
yyy.yyy.yyy.yyy
Set the gateway information for an external print server.
yyy.yyy.yyy.yyy
![Page 210 of the Lexmark MS811 user manual — Parallel [x] menu](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-210.webp?w=400)
Understanding the printer menus 210
Set the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the parallel input buffer.
Disabled Auto 3K to [maximum size allowed]
![Page 211 of the Lexmark MS811 user manual — Parallel [x] menu](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-211.webp?w=400)
Understanding the printer menus 211
Temporarily store print jobs on the printer hard disk before printing.
Enable bidirectional communication through the parallel port.
Specify the parallel port protocol.
Determine if the printer honors printer hardware initialization requests from the computer.
Determine if the parallel port data is sampled on the leading or trailing edge of a strobe.
Set the printer to process Macintosh binary PostScript print jobs.
Set the network address information for an external print server.
yyy.yyy.yyy.yyy
Set the netmask information for an external print server.
yyy.yyy.yyy.yyy
![Page 212 of the Lexmark MS811 user manual — Serial [x] menu](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-212.webp?w=400)
Understanding the printer menus 212
Set the gateway information for an external print server.
yyy.yyy.yyy.yyy
Set the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.

Understanding the printer menus 213
Set the size of the serial input buffer.
Disabled Auto 3K to [maximum size allowed]
Temporarily store print jobs on the printer hard disk before printing.
Select the hardware and software handshaking settings for the serial port.
Determine whether the printer communicates availability to the computer.

Understanding the printer menus 214
Specify the rate at which data can be received through the serial port.
1200 2400 4800 9600 19200 38400 57600 115200 138200 172800 230400 345600
Specify the number of data bits sent in each transmission frame.
Set the parity for serial input and output data frames.
Even Odd None Ignore
Determine whether the printer uses the DSR Signal.
Primary SMTP Gateway Specify SMTP server gateway and port information.
Secondary SMTP Gateway Port
5–30 Specify the amount of time in seconds before the server stops trying to send an e‑mail.
Reply Address Specify a reply address of up to 128 characters in the e-mail sent by the printer.

Understanding the printer menus 215
Set the printer to use SSL for increased security when connecting to the SMTP server.
Specify the type of user authentication required for printing privileges.
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specify what credentials will be used when communicating to the SMTP server. Some SMTP servers require credentials to send an e- mail.
None Use Device SMTP Credentials
User‑Initiated E‑mail
None Use Device SMTP Credentials Use Session User ID & Password Use Session E‑mail address & Password Prompt User
Create a backup password.

Understanding the printer menus 216
Edit settings for Internal Accounts, NTLM, Simple Kerberos Setup, Kerberos Setup, Active Directory, LDAP, Password, and PIN.
Internal Accounts NTLM Simple Kerberos Setup Kerberos Setup Active Directory LDAP LDAP+GSSAPI Password PIN
Add or edit a security template.
[list of available templates]
Control access to printer menus, firmware updates, held jobs, and other access points.
Administrative Menus Function Access Management Solutions Cancel jobs at the Device
Limit the number and time frames of failed login attempts from the printer control panel before all users are locked out.
Login failures Failure time frame Lockout time Panel Login Timeout Remote Login Timeout
1–16 Limit the digit length of the PIN.

Understanding the printer menus 217
Limit the number of times an invalid PIN can be entered.
Limit the amount of time a confidential print job stays in the printer before it is deleted.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs needing verification.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs for printing at a later time.
Off 1 hour 4 hours 24 hours 1 week
Erase Temporary Data Files deletes only print job data on the printer hard disk that are not currently in use by the file system. All permanent data on the printer hard disk are preserved, such as downloaded fonts, macros, and held jobs.

Understanding the printer menus 218
Specify the mode for erasing temporary data files.
Mark all disk space used by a previous print job. This method does not permit the file system to reuse this space until it has been cleared.
Single pass Multiple pass
Export Log Let an authorized user export the audit log.
Specify whether or not audit logs are deleted.
Specify how and whether or not audit logs are created.
Yes No Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of events to log
Current Date and Time Show the current date and time settings for the printer.

Understanding the printer menus 219
Manually Set Date and Time
Enter the date and time.
Select the time zone.
[list of time zones]
Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting.
Enable Network Time Protocol, which synchronizes the clocks of devices on a network.

Understanding the printer menus 220
Set the language of the text that appears on the display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese
View supply estimates on the control panel, Embedded Web Server, menu settings, and device statistics reports.
Show estimates Do not show estimates
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper
Reduce printer noise.
Run the setup wizard.

Understanding the printer menus 221
Specify a language and custom key information for the keyboard on the display.
English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portuguese Russian Polski Swiss German Swiss French Korean Magyar Turkish Czech Simplified Chinese Traditional Chinese Japanese Custom Key 1 Custom Key 2
Specify the unit of measurement for paper sizes.

Understanding the printer menus 222
Specify the display information in the upper corners of the home screen.
Left side Right side
Select from the following options:
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Custom Text [x] Model Name
Customize the text to display in the upper corners of the home screen.
Specify the display information for Black Toner.
Select from the following options:
Do not display Display Message to Display

Understanding the printer menus 223
Specify the display information for Paper Jam, Load Paper, and Service Errors.
Paper Jam Load Paper Service Errors
Select from the following options:
Yes No Message to Display
Change the icons that appear on the control panel.
Change language Search Held Jobs Held Jobs USB Drive Profiles and Apps Bookmarks Jobs by user
Select from the following options:
Display Do not display
Change the icons that appear on the control panel.
Forms and Favorites Background and Idle Screen Eco-Settings
Select from the following options:
Display Do not display
Format the printer date.
MM‑DD‑YYYY DD‑MM‑YYYY YYYY‑MM‑DD

Understanding the printer menus 224
Format the printer time.
12 hour A.M./P.M. 24 hour clock
20–100 Specify the brightness of the display.
Set the amount of light from the bin.
Set the button volume and feedback.
Specify whether to display bookmarks from the Held Jobs area.
Web Page Refresh Rate
30–300 Specify the time between Embedded Web Server refreshes.
Contact Name Specify a contact name for the printer.

Understanding the printer menus 225
Location Specify the printer location.
Set an alarm when the printer requires user intervention. Select from the following options:
Alarm Control Cartridge Alarm Staple Alarm Hole Punch Alarm
Set the idle time before the printer enters a lower power state.
Set the idle time before the printer begins operating in Sleep Mode.
Print a job with the display turned off.
Print with Display Off
Allow printing with display off Display on when printing

Understanding the printer menus 226
Set the time before the printer enters Hibernate mode.
Disabled 20 minutes 1 hour 2 hours 3 hours 6 hours 1 day 2 days 3 days 1 week 2 weeks 1 month
Set the printer to Hibernate mode even if there is an active Ethernet or fax connection.
Hibernate Timeout on Connection
Hibernate Do Not Hibernate
Set the idle time before the display automatically returns to Ready state.
Remain in the same location and reset the Screen Timeout timer instead of returning to the home screen.
Set the printer to end a print job after it has been idle for the specified amount of time.
Set the time the printer waits to receive for more data before canceling a print job.

Understanding the printer menus 227
Set the time the printer waits for user intervention before it holds jobs that require unavailable resources.
Set the printer to restart when an error occurs.
Reboot when idle Reboot always Reboot never
Determine the number of automatic reboots the printer can perform.
Let the printer automatically continue printing from certain offline situations when these are not resolved within the specified time period.
Specify whether the printer reprints jammed pages.
Set the printer to check for jammed paper automatically.
Set the printer to print the correct output for a page.
Remain in the same location and reset the Screen Timeout timer instead of returning to the home screen.

Understanding the printer menus 228
Adjust the Voice Guidance speaking rate.
Very Slow Slow Normal Fast Faster Very Fast Rapid Very Rapid Fastest
Set the headphones volume.
Information Sent to Lexmark
Send anonymous device usage information to Lexmark.
Supplies and Page Usage (Anonymous)
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Do Nothing Sleep Hibernate
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Do Nothing Sleep Hibernate
Restore the printer factory default settings.
Do Not Restore Restore Now
Select a custom home message that appears as an alternating display of the printer status.
Off IP Address Hostname Contact Name Location Zero Configuration Name Custom Text 1
Export the configuration package to a flash drive.

Understanding the printer menus 229
Export Compressed Logs File
Export the compressed logs file to a flash drive.
1–999 Specify a default number of copies for each print job.
Set a default paper source for all print jobs.
Tray [x] Multipurpose Feeder1
Manual Paper Manual Envelope
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether prints are on one side or on both sides of the page.
1 sided 2 sided
Specify whether prints are stapled.
Specify whether prints have holes for binding.
Specify the number of holes to be made on the prints.
2 holes 3 holes 4 holes
1 This menu appears only in touch‑screen printer models.
2 This menu appears only in non‑touch‑screen printer models.

Understanding the printer menus 230
Define the way duplexed pages are bound and printed.
Long Edge Short Edge
Specify the orientation of a multiple‑page document.
Specify that multiple‑page images be printed on one side of a paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Print a border on each page image when using N‑Up (pages per side).
Specify the positioning of multiple‑page images when using N‑Up (pages per side).
Horizontal Reverse Horizontal Reverse Vertical Vertical
1 This menu appears only in touch‑screen printer models.
2 This menu appears only in non‑touch‑screen printer models.

Understanding the printer menus 231
Specify if blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Tray [x] Manual Feeder Multipurpose Feeder1
Specify if blank pages are inserted in a print job.
Do Not Print Print
1 This menu appears only in touch‑screen printer models.
2 This menu appears only in non‑touch‑screen printer models.
Set the default printer language.
PCL Emulation PS Emulation

Understanding the printer menus 232
Specify that print jobs be removed from the print queue when they require unavailable printer options or custom settings. They are stored in a separate print queue, so other jobs print normally. When the missing information or options, or both are obtained, the stored jobs print.
Set the logical and physical printable area.
Normal Fit to Page Whole Page
Set the storage location for downloads.

Understanding the printer menus 233
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a print job that requires more than the available memory.
Specify the order in which held and confidential jobs are printed when Print All is selected.
Alphabetical Oldest First Newest First
Specify whether two‑sided (duplex) printing is set as the default for all print jobs.
1 sided 2 sided
Choose File > Print, and then adjust the settings from the Print dialog and pop‑up menus.
Define the way duplexed pages are bound and printed.
Long Edge Short Edge
1–999 Specify the default number of copies for each print job.
1 This menu appears only in touch‑screen printer models.
2 This menu appears only in non‑touch‑screen printer models.

Understanding the printer menus 234
Specify whether blank pages are inserted in a print job.
Do Not Print Print
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages
Specify the paper source for the separator sheet.
Print multiple‑page images on one side of a paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the positioning of multiple‑page images when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
1 This menu appears only in touch‑screen printer models.
2 This menu appears only in non‑touch‑screen printer models.

Understanding the printer menus 235
Specify the orientation of a multiple‑page document.
Print a border when using Paper Saver.
Specify whether printed output is stapled.
Run Stapler Test Print a report that confirms that the staple finisher is functioning properly.
Specify whether holes will be created on printed outputs for the purpose of collecting the sheets in a binder or folder.
Specify the number of holes to be created on printed outputs for the purpose of collecting the sheets in a binder or folder.
2 holes 3 holes 4 holes
Offset pages at certain instances.
None Between Copies Between Jobs
1 This menu appears only in touch‑screen printer models.
2 This menu appears only in non‑touch‑screen printer models.

Understanding the printer menus 236
Specify the printed output resolution in dots per inch.
300 dpi 600 dpi 1200 dpi 1200 Image Q 2400 Image Q
Enable more pixels to print in clusters for clarity, in order to enhance images horizontally or vertically, or to enhance fonts.
Off Fonts Horizontally Vertically Both directions
1–10 Lighten or darken the printed output.
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Automatically adjust the contrast enhancement applied to images.
Adjust the printed output either by lightening or darkening it. You can conserve toner by lightening the output.
‑6 to 6
0–5 Adjust the contrast of printed objects.
Set if the printer creates a log of the print jobs it receives.

Understanding the printer menus 237
Job Accounting Utilities Print and delete log files or export them to a flash drive.
Set how often a log file is created.
Log Action at End of Frequency
Set how the printer responds when the frequency threshold expires.
None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Log Near Full Level
Specify the maximum size of the log file before the printer executes the Log Action at Near Full.
Log Action at Near Full
Set how the printer responds when the hard disk is nearly full.
None E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
Log Action at Full
Set how the printer responds when disk usage reaches the maximum limit (100MB).
None E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
URL to Post Logs Set where the printer posts job accounting logs.
E‑mail to Send Logs Specify the e‑mail address to which the device sends job accounting logs.
Log File Prefix Specify the prefix you want for the log file name.

Understanding the printer menus 238
Delete confidential and held jobs from the printer hard disk.
Confidential Held Not Restored All
Format the flash memory.
Delete Downloads on Disk
Delete downloads from the printer hard disk, including all held jobs, buffered jobs, and parked jobs.
Delete Now Do Not Delete
Activate Hex Trace Assist in isolating the source of a print job problem.
Provide an estimate of the percentage coverage of toner on a page. The estimate is printed on a separate page at the end of each print job.
Print a page containing information on errors, including XML markup errors.

Understanding the printer menus 239
Scale page content to fit the selected paper size.
Print annotations in a PDF.
Do Not Print Print
Print a page containing the PostScript error.
Lock PS Startup Mode
Disable the SysStart file.
Establish the font search order.
Specify the set of fonts used by the Font Name menu.
Resident Disk Download Flash All

Understanding the printer menus 240
Identify a specific font and the option where it is stored.
Specify the symbol set for each font name.
Change the point size for scalable typographic fonts.
1.00–1008.00
Specify the font pitch for scalable monospaced fonts.
0.08–100
Specify the orientation of text and graphics on the page.
Specify the number of lines that print on each page.

Understanding the printer menus 241
Set the printer to print on A4‑size paper.
198 mm 203 mm
Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR
Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Env
Display the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T1 Default = 4 T1 Default = 5 T1 Default = 20 T1 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3

Understanding the printer menus 242
Restore all tray and feeder assignments to the factory default settings.
Sets the orientation of the text and graphics on the page
1–255 Sets the number of lines that print on each page
0.25–30.00 Sets the number of lines that print per inch
Sets the logical and physical printable area of the page
Specifies a default character set for PPDS print jobs
Replaces a missing font with a similar font

Understanding the printer menus 243
Configures the printer to work with printer software or programs that use different source assignments for trays, drawers, and feeders
Auto CR after LF
Specifies whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command
Auto LF after CR
Specifies whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command

Understanding the printer menus 244
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTJA NewSansMTCS NewSansMTCT NewSansMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers
1–255 pt Set the default font size for HTML documents.
1–400% Scale the default font for HTML documents.
Set the page orientation for HTML documents.
8–255 mm Set the page margin for HTML documents.

Understanding the printer menus 245
Specify whether to print backgrounds on HTML documents.
Do Not Print Print
Select the optimal paper size, scaling, and orientation.
Invert bitonal monochrome images.
Scale the image to fit the selected paper size.
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width
Set the image orientation.
Portrait Landscape Reverse Portrait Reverse Landscape
Print All Guides Prints all the guides
Print Quality Provides information about solving print quality issues
Printing Guide Provides information about loading paper and other specialty media
Media Guide Provides a list of the paper sizes supported in trays and feeders
Print Defects Guide Provides a template for determining the cause of repeating print quality defects, and lists settings that can be used to adjust print quality
Menu Map Provides a list of the control panel menus and settings
Information Guide Provides help in locating additional information
Connection Guide Provides information about connecting the printer locally (USB) or to a network

Understanding the printer menus 246
Moving Guide Provides instructions for safely moving the printer
Supplies Guide Provides information about ordering supplies
Menu item Description

Saving money and the environment 247
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
To save energy, or if you have trouble reading the display, adjust its brightness settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Click Submit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see the following:
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 181.

Saving money and the environment 248
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Select the product you want to recycle.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
The Lexmark Cartridge Collection Program allows you to return used cartridges for free to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. The boxes used to return the cartridges are also recycled.

Saving money and the environment 249
To return Lexmark cartridges for reuse or recycling, do the following:
1 Go to www.lexmark.com/recycle.
2 Select the product that you want to recycle.

Maintaining the printer 250
Ordering supplies
To order parts and supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, go to www.lexmark.com or contact the place where you purchased the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, the estimated cartridge yield is based on approximately 5% coverage per page.

Maintaining the printer 251

* This supply item is supported only in MS811 and MS812 printer models.
For more information on countries located in each region, go to www.lexmark.com/regions.

1 This supply item is supported only in MS810 printer model.
2 This supply item is supported only in MS811 and MS812 printer models.
For more information on countries located in each region, go to www.lexmark.com/regions.

* This supply item is supported only in MS818 printer model. For more information on countries located in each region, go to www.lexmark.com/regions.

Maintaining the printer 252
High yield toner cartridge 53B0HA01
Extra high yield toner cartridge 53B0XA02
1 This supply item is supported only in MS817 printer model.
2 This supply item is supported only in MS818 printer model.
For more information on countries located in each region, go to www.lexmark.com/regions.
Extremely low print coverage for extended periods of time may cause imaging unit parts to fail prior to exhaustion of toner.
For more information on replacing the imaging unit, see the instruction sheet that came with the supply.
Part name Lexmark Return Program Regular
Imaging unit 520Z 520ZA
Ordering a roller kit
For more information on replacing the roller kit, see the instruction sheet that came with the part.
Printer engine roller maintenance kit 40X7706
To identify the supported fuser type, view the label on the fuser. Do either of the following:

Maintaining the printer 253
Fuser maintenance kit type Part number
Fuser maintenance kit type Part number
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:

Maintaining the printer 254
1 Lift the front cover, and then pull down the multipurpose feeder door.

2 Pull the cartridge out of the printer using the handle.


Maintaining the printer 255
3 Unpack the new toner cartridge, then remove the packing material, and then shake the cartridge to redistribute the toner.

4 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.

5 Close the multipurpose feeder door and the front cover.

Maintaining the printer 256
1 Lift the front cover, and then pull down the multipurpose feeder door.
2 Pull out the toner cartridge from the printer using the handle.
3 Lift the green handle, and then pull out the imaging unit from the printer.



Maintaining the printer 257
4 Unpack the new imaging unit, and then shake it.

5 Remove all packing material from the imaging unit.

6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrows on the side rails inside the printer.


Maintaining the printer 258
7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.
8 Close the multipurpose feeder door and the front cover.

Maintaining the printer 259
1 Open the stapler door.

2 Pull down the latch of the staple cartridge holder, and then pull the holder out of the finisher.


3 Squeeze both sides of the empty staple case with your fingers, and then remove the staple case from the cartridge.


Maintaining the printer 260
4 Insert the front side of the new staple case into the staple cartridge, and then push the rear side into the cartridge.

5 Push the staple cartridge into the finisher until it clicks into place.
6 Close the stapler door.
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Wipe the outside of the printer with a damp, soft, lint‑free cloth.
5 Connect the power cord to the electrical outlet, and then turn on the printer.

Maintaining the printer 261
1 Pull out the hole punch box.

2 Empty the container.

3 Insert the emptied hole punch box back into the finisher until it clicks into place.



Maintaining the printer 262
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.

Carefully select paper and specialty media and load them properly to avoid paper jams. For more information, see “Avoiding jams” on page 263. If jams occur, then follow the steps outlined in this chapter.

Clearing jams 263



– If the bin extender is shorter than the size of the paper you are printing on, then the paper causes a
jam in the mailbox bin. For example, if you are printing on a legal-size paper and the bin extender is set to letter-size, then a jam occurs. – If the bin extender is longer than the size of the paper you are printing on, then the edges become
uneven and the paper is not stacked properly. For example, if you are printing on a letter-size paper and the bin extender is set to legal-size, then the paper does not stack properly.
Clearing jams 264



Clearing jams 265




10 Staple finisher rear door

1 Open the front cover and the multipurpose feeder.
2 Remove the toner cartridge.
3 Remove the imaging unit.
Clearing jams 267

4 Remove the jammed paper.

5 Insert the imaging unit.
6 Insert the toner cartridge.
7 Close the multipurpose feeder door and the front cover.
8 If necessary, press on the control panel.
Clearing jams 268

1 Open the rear door.

2 Remove the jammed paper.
3 Close the rear door.
Clearing jams 269

4 Push the back of the standard tray.

5 Remove the jammed paper.


6 Insert the standard tray.
7 If necessary, press on the control panel.
Clearing jams 270

1 Remove the jammed paper.

2 If necessary, press on the control panel.
1 Remove the tray.


2 Remove the jammed paper.

Clearing jams 271

3 Insert the tray.
4 If necessary, press on the control panel.
1 Remove the tray.

2 Remove the jammed paper.
Clearing jams 272

3 Insert the tray.
4 If necessary, press on the control panel.
1 Remove paper from the multipurpose feeder.
2 Remove the jammed paper.

3 Flex, fan, and align the paper edges before loading.

Clearing jams 273

4 Reload paper, and then adjust the paper guide.


5 If necessary, press on the control panel.
1 Remove the jammed paper.

Clearing jams 274

2 Open the rear staple finisher door.

3 Remove the jammed paper.
4 Close the door.
5 If necessary, press on the control panel.
Clearing jams 275

1 Open the staple access door.
2 Remove the staple cartridge holder.
3 Open the staple guard, and then remove the loose staples.

Clearing jams 276

4 Close the staple guard.

5 Press the staples against the metal bracket.

Clearing jams 277


6 Insert the staple cartridge holder.
7 Close the staple access door.
8 If necessary, press on the control panel.
Clearing jams 278

1 Open the rear output expander door.

2 Remove the jammed paper.
3 Close the door.
4 If necessary, press on the control panel.
Clearing jams 279

1 Open the rear mailbox door.

2 Remove the jammed paper.
3 Close the door.
4 If the jam is in the mailbox bin, then remove the jammed paper.
Clearing jams 280


5 If necessary, press on the control panel.
Clearing jams 281
![Page 282 of the Lexmark MS811 user manual — Change [paper source] to [paper type] [paper size] load [orientation]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-282.webp?w=400)
Understanding the printer messages
Use only a supported toner cartridge and imaging unit.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Touch Cancel job to cancel the print job.
Try one or more of the following
non‑touch‑screen printer models, press to confirm. • Cancel the print job.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Cancel the print job.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Cancel the print job.
Troubleshooting 282
![Page 283 of the Lexmark MS811 user manual — Complex page, some data may not have printed [39]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-283.webp?w=400)
Try one or more of the following:
If the error occurs a second time, then:
1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the specified tray. 4 Reattach the tray. 5 Connect the power cord to a properly grounded electrical outlet. 6 Turn the printer back on.
If the error occurs again, then:
1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the tray. 4 Contact customer support. • To clear the message and resume the job, select Continue on the printer control panel. For non-touch-
screen printer models, press to confirm.
The toner cartridge is missing or not installed properly. Insert the cartridge, and then close all doors and covers.
Close the finisher rear door of the printer.
Close the rear door of the printer.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm.
Troubleshooting 283

Held jobs are invalidated because of any of the following possible changes in the printer:
From the printer control panel, select Continue to clear the message. For non-touch-screen printer models,
press to confirm.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Cancel the current print job.
Try one or more of the following:
From the printer control panel, select Format disk to format the printer hard disk and clear the message.
Disk near full. Securely clearing disk space.
Try one or more of the following:
Troubleshooting 284
![Page 285 of the Lexmark MS811 user manual — Incompatible output bin [x] [59]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-285.webp?w=400)
Try one or more of the following:
Error reading USB drive. Remove USB.
An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
You may need to order an imaging unit. If necessary, select Continue on the printer control panel to clear
the message and continue printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the imaging unit very soon. For more information, see the "Replacing supplies" section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
the specified bin. For non-touch-screen printer models, press to confirm.
Troubleshooting 285
![Page 286 of the Lexmark MS811 user manual — Insert Tray [x]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-286.webp?w=400)
Try one or more of the following:
using the specified tray. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
Insert the hole punch box into the finisher, and then select Continue on the printer control panel to clear
the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
printer models, press to confirm.
Try one or more of the following:
Troubleshooting 286
![Page 287 of the Lexmark MS811 user manual — Insufficient memory, some Held Jobs were deleted [37]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-287.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
The printer deleted some held jobs in order to process current jobs.
Select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Troubleshooting 287
![Page 288 of the Lexmark MS811 user manual — Load [paper source] with [custom type name] [paper orientation]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-288.webp?w=400)
Try one or more of the following:
models, press to confirm. • Delete other held jobs to free up additional printer memory.
Try one or more of the following:
collating the rest of the print job. For non‑touch‑screen printer models, press to confirm. • Cancel the current print job.
Install additional printer memory or select Continue on the printer control panel to disable Resource Save,
clear the message, and continue printing. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
control panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
control panel. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 288
![Page 289 of the Lexmark MS811 user manual — Load multipurpose feeder with [custom type name] [orientation]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-289.webp?w=400)
Try one or more of the following:
control panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
the printer control panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 289
![Page 290 of the Lexmark MS811 user manual — Maintenance kit nearly low [80.xy]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-290.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
You may need to order a maintenance kit. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer
models, press to confirm.
For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer
models, press to confirm.
Troubleshooting 290
![Page 291 of the Lexmark MS811 user manual — Non ‑ Lexmark [supply type], see User’s Guide [33.xy]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-291.webp?w=400)
You may need to replace the maintenance kit very soon. For more information, contact customer support at http://support.lexmark.com or your service representative.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
models, press to confirm. • Install additional printer memory.
Select Continue on the control panel to clear the message and continue printing. For non‑touch‑screen
printer models, press to confirm.
Try one or more of the following:
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third- party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. For more information, see “Using genuine Lexmark parts and supplies” on page 250.
All life indicators are designed to function with Lexmark supplies and parts and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.
To accept any and all of these risks and to proceed with the use of non-genuine supplies or parts in your
printer, press and hold and the # button on the control panel simultaneously for 15 seconds.
Troubleshooting 291
![Page 292 of the Lexmark MS811 user manual — Parallel port [x] disabled [56]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-292.webp?w=400)
For non‑touch‑screen printer models, press and on the control panel simultaneously for 15 seconds to clear the message and continue printing.
If you do not want to accept these risks, then remove the third-party supply or part from your printer and install a genuine Lexmark supply or part.
Try one or more of the following:
Try one or more of the following:
For non-touch-screen printer models, press to confirm. • Cancel the current print job.
Try one or more of the following:
The printer discards any data received through the parallel port. • Select Reset active bin to reset the bin for a linked set of bins.
Printer had to restart. Last job may be incomplete.
Select Continue on the control panel to clear the message and continue printing. For non‑touch‑screen
printer models, press to confirm.
For more information, go to http://support.lexmark.com or contact customer support.
Troubleshooting 292
![Page 293 of the Lexmark MS811 user manual — Reattach bins [x] – [y]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-293.webp?w=400)
Try one or more of the following:
bin. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
Select Continue on the printer control panel to clear the message and print without using the specified
bins. For non-touch-screen printer models, press to confirm.
Troubleshooting 293
![Page 294 of the Lexmark MS811 user manual — Remove paper from bin [x]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-294.webp?w=400)
Try one or more of the following:
For information on installing the toner cartridge, see the “Replacing supplies” section. • If the toner cartridge is installed, then remove and reinstall the unresponsive toner cartridge.
Try one or more of the following:
For information on installing the imaging unit, see the “Replacing supplies” section. • If the imaging unit is installed, then remove and reinstall the unresponsive imaging unit.
Remove and replace the defective printer hard disk.
1 Remove any remaining packaging material from the specified location.
2 Select Continue to clear the message and continue printing. For non‑touch‑screen printer models,
press to confirm.
Bins have reached their capacity. Remove paper from all bins to clear the message and continue printing.
If removing the paper does not clear the message, then select Continue on the printer control panel. For
non-touch-screen printer models, press to confirm.
Remove paper from the specified bin. The printer automatically detects paper removal and resumes printing.
If removing the paper does not clear the message, then select Continue on the printer control panel. For
non-touch-screen printer models, press to confirm.
Troubleshooting 294
![Page 295 of the Lexmark MS811 user manual — Replace defective imaging unit [31.xy]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-295.webp?w=400)
Remove paper from the specified bin. The printer automatically detects paper removal and resumes printing.
If removing the paper does not clear the message, then select Continue on the printer control panel. For
non-touch-screen printer models, press to confirm.
Remove the paper stack from the standard bin. The printer automatically detects paper removal and resumes printing.
If removing the paper does not clear the message, then select Continue on the printer control panel. For
non-touch-screen printer models, press to confirm.
Install a toner cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:
1 United States, Canada
2 European Economic Area (EEA), Switzerland
3 Asia Pacific, Australia, New Zealand
5 Africa, Middle East, rest of Europe
Replace the defective imaging unit to clear the message. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
![Page 296 of the Lexmark MS811 user manual — Replace unsupported cartridge [32.xy]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-296.webp?w=400)
Replace the imaging unit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
For more information, go to http://support.lexmark.com or contact customer support.
Depending on your printer model, touch Continue or press to clear the message and continue printing.
For more information, go to http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer
models, press to confirm.
Install the missing toner cartridge to clear the message. For more information, see the “Replacing supplies” section of the User’s Guide.
Install the missing fuser. For more information, see the instruction sheet that came with the replacement part.
Install the missing imaging unit to clear the message. For more information, see the “Replacing supplies” section of the User’s Guide.
1 Replace the roller kit. For more information, see the instruction sheet that came with the part.
2 Press to clear the message and continue printing.
Remove the toner cartridge, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
Troubleshooting 296

This error can also be caused by installing a genuine Lexmark cartridge, such as a high yield cartridge, that is not intended to be used in this product.
The following error codes indicate that a non‑genuine Lexmark toner cartridge is installed:
32.13 32.16 32.19 32.22 32.25 32.28 32.31 32.34 32.37
For more information, see “Using genuine Lexmark parts and supplies” on page 250.
Remove the imaging unit, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
This error can also be caused by installing a genuine Lexmark imaging unit, such as a MICR unit, that is not intended to be used in this product.
The following error codes indicate that a non‑genuine Lexmark imaging unit is installed:
32.14 32.17 32.20 32.23 32.26 32.29 32.32 32.35 32.38
For more information, see “Using genuine Lexmark parts and supplies” on page 250.
1 Replace the fuser wiper. For more information, see the instruction sheet that came with the part.
2 Select Continue on the control panel to clear the message and continue printing. For non‑touch‑screen
printer models, press to confirm.
Troubleshooting 297
![Page 298 of the Lexmark MS811 user manual — Standard USB port disabled [56]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-298.webp?w=400)
Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Select Do not restore if you do not want any print jobs to be restored. For non‑touch‑screen printer
models, press to confirm.
Try one or more of the following:
Select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models,
press to confirm.
Troubleshooting 298
![Page 299 of the Lexmark MS811 user manual — Too many trays attached [58]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-299.webp?w=400)
A supply needed to complete the job is missing. Cancel the current job.
The device is operating in Safe Mode. Some print options may be disabled or provide unexpected results.
Select Continue to clear the message. For non‑touch‑screen printer models, press to confirm.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra bins.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra printer hard disks.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra flash memory.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra trays.
Troubleshooting 299
![Page 300 of the Lexmark MS811 user manual — USB port [x] disabled [56]](/cdn/reader/0a/0aaebab7337a41b9bc20ba2025060c696816a6510add4811cdb96b61267061c5/images/page-300.webp?w=400)
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
The paper size in the specified tray is unsupported. Replace it with a supported paper size.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Format the flash memory.
1 Remove the unsupported disk, and then install a supported one.
2 Select Continue to clear the message and continue printing. For non‑touch screen printer models,
press to confirm.
1 Turn off the printer.
2 Unplug the power cord from the wall outlet.
3 Remove the unsupported option card from the printer controller board, and then replace it with a supported card.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Try one or more of the following:
Troubleshooting 300

Go to step 2. Turn on the printer.
Make sure the printer is turned on.
Is the printer turned on?
Step 2 Check if the printer is in Sleep mode or Hibernate mode.
Press the Sleep button to wake the printer from Sleep mode or Hibernate mode.
Go to step 3.
Is the printer in Sleep mode or Hibernate mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Does other electrical equipment work?
Step 5 Check if the cables connecting the printer and the computer are inserted in the correct ports.
Go to step 6. Make sure to match the following:
Are the cables inserted in the correct ports?

Turn on the switch or reset the breaker.
Go to step 7.
Make sure the electrical outlet is not turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Make sure to install all hardware options properly and remove any packing material.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?
Go to step 12. Install the correct printer driver.
Check the installed printer driver.
Is the correct printer driver installed?
The problem is solved.
Contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Is the printer working?

The problem is solved.
Go to step 2.
Press the Sleep button on the printer control panel.
Does Ready appear on the printer display?
The problem is solved.
Turn off the printer, and then contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Do Please wait and Ready appear on the printer display?
The problem is solved.
Go to step 2.
a From the control panel, check if the documents appear in the
Held Jobs list.
Are the documents printed?
The problem is solved.
Go to step 3.
The print job may contain a formatting error or invalid data.
Are the documents printed?

The problem is solved.
Go to step 4.
If you are printing from the Internet, then the printer may be reading the multiple job titles as duplicates.
a Open the Printing Preferences dialog. b From the Print and Hold section, select Keep duplicate
documents. c Enter a PIN. d Resend the print job.
a Save and name each job differently. b Send the job individually.
Are the documents printed?
The problem is solved.
Go to step 5.
a Delete some held jobs to free up printer memory. b Resend the print job.
Are the documents printed?
The problem is solved.
Contact customer support.
a Add printer memory. b Resend the print job.
Are the documents printed?
a Use envelopes that have been stored in a dry environment.
Contact customer support.
The problem is solved.
Does the envelope seal when printing?

Go to step 2. Insert the flash drive into the front USB slot.
Check if the flash drive is inserted into the front USB slot.
Is the flash drive inserted into the front USB slot?
Step 2 Check if the indicator light on the printer control panel is blinking green.
Wait until the printer is ready, then view the held jobs list, and then print the documents.
Go to step 3.
Is the indicator light blinking green?
Go to step 4. The problem is solved.
a Check for an error message on the display. b Clear the message.
Does the error message still appear?
Go to step 5. The problem is solved.
Check if the flash drive is supported.
For more information on tested and approved USB flash drives, see “Supported flash drives and file types” on page 68 for non‑touch‑screen printer models. For touch‑screen printer models, see “Supported flash drives and file types” on page 116 and “Supported flash drives and file types” on page 164.
Does the error message still appear?
Contact customer support.
The problem is solved.
Check if the USB slot is disabled by the system support person.
Does the error message still appear?

Deactivate Hex Trace mode.
Go to step 2.
Make sure the printer is not in Hex Trace mode.
Is the printer in Hex Trace mode?
Contact customer support.
The problem is solved.
a From the printer control panel, select Standard Network or
Network [x], and then set SmartSwitch to On. b Resend the print job.
Do incorrect characters print?
The problem is solved.
Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved.
Go to step 3.
a From the Paper menu on the printer control panel, set the paper
size and type to match the paper loaded in the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved.
Go to step 4.
a Depending on your operating system, open Printing
Preferences or the Print dialog, and then specify the paper type. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved.
Contact customer support.
a Check if the trays are not linked. b Resend the print job.
Did the job print from the correct tray or on the correct paper?

The problem is solved.
Go to step 2.
a From the Finishing menu on the printer control panel, set
Collate to (1,2,3) (1,2,3). b Resend the print job.
Did the job print and collate correctly?
The problem is solved.
Go to step 3.
a From the printer software, set Collate to (1,2,3) (1,2,3).
Did the job print and collate correctly?
The problem is solved.
Contact customer support.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Did the job print and collate correctly?
Multiple‑language PDF files do not print
The problem is solved.
Go to step 2.
a Check if the print options for the PDF output are set to embed
all fonts. b Generate a new PDF file, and then resend the print job.
Do the files print?
The problem is solved.
Contact customer support.
a Open the document you want to print in Adobe Acrobat. b Click File > Print > Advanced > Print As Image > OK > OK.
Do the files print?

The problem is solved.
Go to step 2.
Change the environmental settings of the printer.
a From the printer control panel, navigate to:
Settings > General Settings b Select Eco‑Mode or Quiet Mode, and then select Off.
Did the job print?
The problem is solved.
Go to step 3.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the job
Did the job print?
The problem is solved.
Go to step 4.
a Remove held jobs stored in the printer memory. b Resend the print job.
Did the job print?
The problem is solved.
Go to step 5.
a Disable the Page Protect feature.
From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Page Protect > Off b Resend the print job.
Did the job print?
The problem is solved.
Contact customer support.
Install additional printer memory, and then resend the print job.
Did the job print?

The problem is solved.
Go to step 2.
a From the document you are trying to print, open the Print dialog
and check if you have selected the correct printer.
Do the jobs print?
The problem is solved.
Go to step 3.
a Check if the printer is plugged in and turned on, and if Ready
appears on the printer display. b Resend the print job.
Do the jobs print?
The problem is solved.
Go to step 4.
If an error message appears on the printer display, then clear the message.
Do the jobs print?
The problem is solved.
Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if
the cables are securely connected to the computer and the printer.
Do the jobs print?
The problem is solved.
Go to step 6.
a Turn off the printer, wait for about 10 seconds, and then turn the
printer back on. b Resend the print job.
Do the jobs print?
The problem is solved.
Contact customer support.
a Remove, and then reinstall the printer software. For more
information, see “Installing the printer software” on page 35.
Do the jobs print?

The problem is solved.
Go to step 2.
a Make sure the size of the paper loaded in the tray matches the
fuser type.
Does the print speed increase?
The problem is solved.
Contact customer support.
a Replace the fuser. For more information on installing the fuser,
see the instruction sheet that came with the part. b Resend the print job.
Does the print speed increase?
The problem is solved.
Go to step 2.
a Open the trays, and then check if they contain paper of the
same size and type.
Do the trays link correctly?

The problem is solved.
Contact customer support.
a From the printer control panel, set the paper size and type in
the Paper menu to match the paper loaded in the trays to be linked.
Do the trays link correctly?
Step 1 Adjust the print timeout settings.
The problem is solved.
Go to step 2.
a From the printer control panel, navigate to:
Settings > General Settings > Timeouts > Print Timeout b Select a higher setting and then, depending on your printer
model, select or Submit. c Resend the print job.
Did the file print correctly?
The problem is solved.
Contact customer support.
a Check the original file for manual page breaks. b Resend the print job.
Did the file print correctly?

The problem is solved.
Go to step 2.
a Pull out the tray, and then do one or more of the following:
Does the tray operate properly?
The problem is solved.
Go to step 3.
Turn off the printer, then wait about 10 seconds, and then turn it back on.
Does the tray operate properly?
Go to step 4. For more information, see the setup sheet that came with the 2100- sheet tray.
Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Is the tray listed in the menu settings page?
Go to step 5. Manually add the tray in the printer driver.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?

The problem is solved.
Contact customer support.
Check if the tray is selected.
From the application you are using, select the tray. If you are using Mac OS X version 9, then make sure the printer is set up in Chooser.
Does the tray operate properly?
The problem is solved.
Go to step 2.
Turn off the printer, then wait for about 10 seconds, and then turn on the printer.
Does the internal option operate correctly?
Go to step 3. Connect the internal option to the controller board.
Check if the internal option is properly installed in the controller board.
a Turn off the printer using the power switch, and then unplug the
power cord from the electrical outlet. b Make sure the internal option is installed in the appropriate
connector in the controller board. c Connect the power cord to the printer, then to a properly
grounded electrical outlet, and then turn on the printer.
Is the internal option properly installed in the controller board?
Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Features list.
Is the internal option listed in the menu settings page?
The problem is solved.
Contact customer support.
a Check if the internal option is selected.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 35. b Resend the print job.
Does the internal option operate correctly?

Go to step 2. Check if the internal print server is supported by the printer.
Reinstall the internal print server.
a Remove, and then install the internal print server. For more
information, see “Installing an Internal Solutions Port” on page 17. b Print a menu settings page, and then check if the internal print
server is listed in the Installed Features list.
Is the internal print server listed in the Installed Features list?
Step 2 Check the cable and the internal print server connection.
The problem is solved.
Contact customer support.
Use the correct cable, and then check if it is securely connected to the internal print server.
Does the internal print server operate correctly?
Go to step 2. Check if you have a supported ISP.
Make sure the Internal Solutions Port (ISP) is installed.
a Install the ISP. For more information, see “Installing an Internal
Solutions Port” on page 17. b Print a menu settings page, and then check if the ISP is listed
in the Installed Features list.
Is the ISP listed in the Installed Features list?
The problem is solved.
Contact customer support.
Check the cable and the ISP connection.
a Use the correct cable, and then make sure it is securely
connected to the ISP. b Check if the ISP solution interface cable is securely connected
into the receptacle of the controller board.
Does the Internal Solutions Port operate correctly?

The problem is solved.
Go to step 2.
a Pull out the tray, and then do one or more of the following:
Is the tray working?
The problem is solved.
Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn
the printer back on. b Resend the print job.
Is the tray working?
Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed and recognized by the printer.
Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Is the tray listed in the menu settings page?
The problem is solved.
Contact customer support.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?

Go to step 2. Check if you have a supported USB or parallel interface card.
Make sure the USB or parallel interface card is installed.
a Install the USB or parallel interface card. For more information,
see “Installing an Internal Solutions Port” on page 17. b Print a menu settings page, and then check if the USB or parallel
interface card is listed in the Installed Features list.
Is the USB or parallel interface card listed in the Installed Features list?
Step 2 Check the cable and the USB or parallel interface card connection.
The problem is solved.
Contact customer support.
Use the correct cable, and then make sure it is securely connected to the USB or parallel interface card.
Does the USB or parallel interface card operate correctly?
a Turn on jam recovery.
The problem is solved.
Contact customer support.
1 From the printer control panel, navigate to:
Settings > General Settings > Print Recovery > Jam Recovery 2 Select On or Auto.
3 Depending on your printer model, press or touch Submit. b Resend the pages that did not print.
Were the jammed pages reprinted?

Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?
Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see
“Avoiding jams” on page 263. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?
a Do either of the following:
Contact customer support.
The problem is solved.
or Done.
Clear the jam, press OK > . b Follow the instructions on the printer display.
Does the paper jam message remain?


Go to step 2. Select a font that is supported by the printer.
a Print a font sample list to check if the fonts you are using are
Menus > Reports > Print Fonts 2 Select PCL Fonts or PostScript Fonts. b Resend the print job.
Are you using fonts that are supported by the printer?
Check if the fonts installed on the computer are supported by the printer.
Are the fonts installed on the computer supported by the printer?

a Move the width and length guides in the tray to the correct
positions for the paper loaded. b Resend the print job.
Troubleshooting 318

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Do the paper size and type match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size
from Printing Preferences or from the Print dialog. b Resend the print job.
Is the page or image clipped?
Contact customer support.
The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge. 2 Remove the imaging unit.
Is the page or image clipped?
The problem is solved.
Go to step 2.
a Make sure the size of the paper loaded in the tray matches the
fuser type.
Do compressed images still appear?


a Replace the fuser. For more information on installing the fuser,
see the instruction sheet that came with the part. b Resend the print job.

a From the Quality Menu on the printer control panel, decrease
Step 2 Reinstall the imaging unit and the toner cartridge.
a Remove the toner cartridge. b Remove the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 320


a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Replace the imaging unit, and then resend the print job.
Troubleshooting 321

ABC DEF ABC DEF
The problem is solved.
Go to step 2.
a Move the width and length guides in the tray to the correct
positions for the paper size loaded. b Resend the print job.
Are the margins correct?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?
The problem is solved.
Contact customer support.
a Depending on your operating system, specify the paper size
from Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?

Go to step 2. Adjust the width and length guides.
Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Are the width and length guides positioned correctly?
Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the paper still curled?
Go to step 5. The problem is solved.
a Remove the paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct
positions for the size of the paper loaded in the tray. b Resend the print job.
Do print irregularities still appear?
Go to step 3. Specify the paper size and type from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Do the printer settings match the type and weight of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do print irregularities still appear?
Step 4 Check if the paper loaded in the tray has texture or rough finishes.
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray.
Go to step 5.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?
Contact customer support at http://support.lexm ark.com or your service representative.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do print irregularities still appear?

ABC DEF ABC DEF
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, reduce the
toner darkness.
Is the print still too dark?
Go to step 3. Do one or more of the following:
a From the printer control panel, set the paper type, texture and
weight in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type,
texture and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too dark?
From the printer control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Check if the paper loaded in the tray has texture or rough finishes.
Are you printing on textured or rough paper?

Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too dark?
ABC DEF
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, increase
the toner darkness.
Is the print still too light?
Go to step 3. Change the paper type, texture, and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type, texture, and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type,
texture, and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too light?

From the printer control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on.
Go to step 5.
Make sure that the paper has no texture or rough finishes.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Is the print still too light?
Go to step 7. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the print still too light?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the print still too light?

Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imaging unit.
Is the printer still printing blank pages?
Go to step 3. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Is the printer still printing blank pages?
Step 3 Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Is the printer still printing blank pages?

Go to step 2. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Is the printer printing solid black pages?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Is the printer printing solid black pages?
Go to step 2. The problem is solved.
a Replace the imaging unit if the distance between the defects is
equal to any of the following:
Do repeating defects still appear on prints?
Contact customer support.
The problem is solved.
a Replace the fuser if the distance between the defects is equal
to either of the following:
Do repeating defects still appear on prints?


Go to step 2. Load paper with the correct paper type and weight in the tray.
Load paper with the correct paper type and weight in the tray.
Is paper with the correct paper type and weight loaded in the tray?
Go to step 3. Change the paper loaded in the tray to match the paper type and weight specified in the tray settings.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do shadow images still appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do shadow images still appear on prints?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct
positions for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the
tray. b Resend the print job.
Is the print still skewed?
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder
from Printing Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines appear on prints?
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked horizontal lines appear on prints?


1 Remove the toner cartridge, and then the imaging unit.
Replace the imaging unit, and then resend the print job.

a Depending on your operating system, specify the paper type,
texture, and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Troubleshooting 332

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper texture, type, and weight in the Paper menu to match the paper loaded in the tray.
Do the paper texture, type, and weight match the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked vertical lines appear on prints?
Go to step 5. The problem is solved.
a Reinstall the imaging unit.
1 Remove the toner cartridge, and then the imaging unit.
Do streaked vertical lines appear on prints?
Step 5 Replace the imaging unit, and then resend the print job.
Contact customer support at http://support.lexm ark.com or your service representative.
The problem is solved.
Do streaked vertical lines appear on prints?


1 Remove the toner cartridge, and then the imaging unit.
Did the toner fog or background shading disappear from the prints?
Replace the imaging unit, and then resend the print job.
Did the toner fog or background shading disappear from the prints?
ABC DEF
Troubleshooting 334 · Leading edge · Trailing edge

Step 1 From the Paper menu on the printer control panel, check the paper type, texture, and weight.
Go to step 2. Specify the paper type, texture, and weight from the tray settings to match the paper loaded in the tray.
Do the paper type, texture, and weight match the paper loaded in the tray?
Contact customer support.
The problem is solved.
Resend the print job.
Does the toner still rub off?
Replace the imaging unit, and then resend the print job.
Contact customer support.
The problem is solved.
Do toner specks appear on prints?
Go to step 2. Set the paper type to Transparency.
From the printer control panel, set the paper type in the Paper menu to match the paper loaded in the tray.
Is the paper type for the tray set to Transparency?
Contact customer support.
The problem is solved.
a Check if you are using a recommended type of transparency. b Resend the print job.
Is the print quality still poor?


Replace the imaging unit, and then resend the print job.
Go to step 2. The problem is solved.
a Make sure your software program is using a correct fill pattern. b Resend the print job.
Do vertical voids appear on prints?
Go to step 3. The problem is solved.
a From the printer control panel, set the paper type and weight
in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Do vertical voids appear on prints?
Go to step 4. The problem is solved.
Check if you are using a recommended type of paper.
a Load the specified tray or feeder with a recommended type of
paper. b Resend the print job.
Do vertical voids appear on prints?
Go to step 5. The problem is solved.
a Redistribute the toner in the imaging unit.
1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit.
Do vertical voids appear on prints?

Contact customer support.
The problem is solved.
Replace the imaging unit, and then resend the print job.
Do vertical voids appear on prints?
This troubleshooting section applies only to touch-screen printer models.
Go to step 2. Contact customer support.
Check the system log for relevant details.
a Open a Web browser, and then type the printer IP address in
the address field.
If you do not know the IP address of the printer, then you can:
Log. c From the Filter menu, select an application status. d From the Application menu, select an application, and then
click Submit. Does an error message appear in the log?
The problem is solved.
Contact customer support.
Resolve the error. Is the application working now?

Go to step 2. Type the correct printer IP address in the address field of your Web browser.
Make sure the printer IP address is correct.
View the printer IP address:
Is the printer IP address correct?
Go to step 3. Turn on the printer.
Check if the printer is turned on.
Is the printer turned on?
Go to step 4. Contact your system support person.
Check if the network connection is working.
Is the network connection working?
Step 4 Make sure the cable connections to the printer and print server are secure.
Go to step 5. Tighten the cable connection.
For more information, see the setup documentation that came with the printer.
Are the cable connections to the printer and print server secure?
Go to step 6. Contact your system support person.
Temporarily disable the Web proxy servers.
Are the Web proxy servers disabled?
Step 6 Access the Embedded Web Server again by typing the correct IP address in the address field.
The problem is solved.
Contact customer support.
Did the Embedded Web Server open?

Before contacting customer support, make sure to have the following information:
Go to http://support.lexmark.com to receive e‑mail or chat support, or browse through the library of manuals, support documentation, drivers, and other downloads.
Technical support via telephone is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, go to http://support.lexmark.com.
Troubleshooting 339

Product name:
Lexmark MS810de, MS810dn, MS810n, MS811dn, MS811n, MS812de, MS812dn, MS817dn, MS817n, MS818dn
Machine type:
Model(s):
Edition notice
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2017 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
May 2017

Lexmark, the Lexmark logo, MarkNet, and MarkVision are trademarks or registered trademarks of Lexmark International, Inc. in the United States and/or other countries.
Google Cloud Print is a trademark of Google Inc.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
Microsoft and Windows are either registered trademarks or trademarks of the Microsoft group of companies in the United States and other countries.
Mopria®, the Mopria® logo, and the Mopria® Alliance logo are registered trademarks and service marks of Mopria Alliance, Inc. in the United States and other countries. Unauthorized use is strictly prohibited.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
PostScript is a registered trademark of Adobe Systems Incorporated in the United States and/or other countries.
The following terms are trademarks or registered trademarks of these companies:
Albertus The Monotype Corporation plc
Antique Olive Monsieur Marcel OLIVE
Apple-Chancery Apple Computer, Inc.
Arial The Monotype Corporation plc
CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation
Chicago Apple Computer, Inc.
Clarendon Linotype-Hell AG and/or its subsidiaries
Geneva Apple Computer, Inc.
GillSans The Monotype Corporation plc
Helvetica Linotype-Hell AG and/or its subsidiaries
Hoefler Jonathan Hoefler Type Foundry
ITC Avant Garde Gothic International Typeface Corporation
ITC Bookman International Typeface Corporation
ITC Mona Lisa International Typeface Corporation
ITC Zapf Chancery International Typeface Corporation
Joanna The Monotype Corporation plc
Monaco Apple Computer, Inc.
New York Apple Computer, Inc.
Eurostile Nebiolo · Marigold Arthur Baker · Oxford Arthur Baker

Palatino Linotype-Hell AG and/or its subsidiaries
Stempel Garamond Linotype-Hell AG and/or its subsidiaries
Times New Roman The Monotype Corporation plc
Univers Linotype-Hell AG and/or its subsidiaries
All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
All licensing notices associated with this product can be viewed from the root directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Printing 57 (MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, and MS818dn); 58 (MS810de and MS812de)
Ready 32 (all models)
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Taffy Agfa Corporation

This product complies with the India E-Waste (Management and Handling) Rules, 2011, which prohibit use of lead, mercury, hexavalent chromium, polybrominated biphenyls, or polybrominated diphenyl ethers in concentrations exceeding 0.1% by weight and 0.01% by weight for cadmium, except for the exemption set in Schedule II of the Rules.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
This symbol identifies static-sensitive parts. Do not touch the areas near these symbols without first touching a metal surface in an area away from the symbol.
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient operating temperature 15.6 to 32.2°C (60 to 90°F)
Shipping temperature -40 to 43.3°C (-40 to 110°F)
Storage temperature and relative humidity 1 to 35°C (34 to 95°F)
8 to 80% RH

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1: 2014.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 15‑milliwatt gallium arsenide laser operating in the wavelength of 787–800 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:
Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku. FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista. GEFAHR - Unsichtbare Laserstrahlung beim Herausnehmen von Druckkassetten und offener Sicherheitssperre. Laserstrahl meiden.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser. VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget.
FARE – Usynlig laserstråling når kassettene tas ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen. NIEBEZPIECZEŃSTWO - niewidzialne promieniowanie laserowe podczas usuwania kaset i blokady. Należy unikać naświetlenia promieniem lasera.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей. Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危險 - 移除碳粉匣與安全連續開關失效時會產生看不見的雷射輻射。請避免曝露在雷射光束下。 危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs.
670 (MS810n, MS810dn, MS817n, and MS817dn); 700 (MS810de); 770 (MS811n, MS811dn, and MS818dn); 830 (MS812dn and MS812de)
Copy The product is generating hard‑copy output from hard‑copy original documents.

Mode Description Power consumption (Watts)
Scan The product is scanning hard‑copy documents. N/A
Ready The product is waiting for a print job. Ready 1: 55 (MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, and MS818dn); 60 (MS810de and MS812de); Ready 2: 30 (All printer models)
Sleep Mode The product is in a high‑level energy‑saving
2.9 (MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS817n, MS817dn, and MS818dn); 3.3 (MS810de); 3.7 (MS812de)
mode.
Hibernate The product is in a low‑level energy‑saving mode.
0.5 (MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS810de, MS817n, MS817dn, and MS818dn); 0.6 (MS812de)
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 20
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.

If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.
The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.
The following information applies to all MS810, MS811, MS812, MS817, and MS818 printer models except for the MS812de printer model.

STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country-specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.

As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.

This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをしてください。
VCCI-B
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 2014/30/EU, 2014/35/EU, 2009/125/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, the ecodesign of energy-related products, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative or may be obtained at www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
This product satisfies the Class B limits of EN 55022 and EN55032 and safety requirements of EN 60950‑1 or EN 62368-1.
The following information applies only to the MS812de printer model.

This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe A est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.

This product is in conformity with the protection requirements of EC Council directives 2014/30/EU, 2014/35/EU, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to

electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative or may be obtained at www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
This product satisfies the Class A limits of EN 55022 and EN55032 and safety requirements of EN 60950‑1 or EN 62368-1.
This is a product that complies with the emission requirements of EN55022 and EN55032 Class A limits and immunity requirements of EN55024. This product is not intended to be used in residential/domestic environments.
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.





Change [paper source] to
Insufficient memory, some held
configurations 41, 83, 130 finishing features 185 minimum clearances 10, 11 models 41, 83, 130 moving 10, 11, 262 selecting a location 10, 11 shipping 262 printer control panel
[paper type] [paper size] load [orientation] 282 Check tray [x] connection 283 Close door or insert
jobs will not be restored [37] 288 Load [paper source] with
[custom string] [paper orientation] 288 Load [paper source] with
cartridge 283 Close finisher rear door 283 Close rear door 283 Complex page, some data may
[custom type name] [paper orientation] 288 Load [paper source] with [paper
adjusting brightness 247 factory defaults,
not have printed [39] 283 Configuration change, some
size] [paper orientation] 289 Load [paper source] with [paper
restoring 78, 124, 173 indicator light 44, 86, 133 parts 43, 85, 132 Sleep button light 44, 86, 133 using 43, 85, 132 printer control panel, virtual display
held jobs were not restored [57] 284 Defective flash detected
type] [paper size] [paper orientation] 289 Load multipurpose feeder with
[51] 284 Disk full [62] 284 Disk must be formatted for use
[custom type name] [orientation] 289 Load multipurpose feeder with
in this device 284 Disk near full. Securely clearing
using the Embedded Web
[paper size] [orientation] 290 Load multipurpose feeder with
Server 120 Printer had to restart. Last job may be incomplete. 292 printer hard disk
disk space. 284 Empty the hole punch box 285 Error reading USB drive.
[paper type] [paper size] [orientation] 290 Load multipurpose feeder with
Remove USB. 285 Error reading USB hub. Remove
disposing of 78, 125, 174 encrypting 81, 128, 176 installing 23 removing 27 wiping 80, 127, 176 printer hard disk encryption 81, 128, 176 printer hard disk memory
custom string] [orientation] 289 Load staples 290 Maintenance kit low
hub. 285 Imaging unit low [84.xy] 285 Imaging unit nearly low
[84.xy] 285 Imaging unit very low, [x]
[80.xy] 290 Maintenance kit nearly low
estimated pages remain [84.xy] 285 Incompatible output bin [x]
[80.xy] 290 Maintenance kit very low
erasing 80, 127, 176 printer information
[80.xy] 291 Memory full [38] 291 Misfeed cleared, extra sheets in
[59] 285 Incompatible tray [x] [59] 286 Incorrect paper size, open
where to find 8 printer IP address
output bin [24y.xx] 291 Network [x] software error
finding 89, 137 printer is printing blank pages 327 printer messages
[paper source] [34] 286 Insert hole punch box 286 Insert staple cartridge 286 Insert Tray [x] 286 Install bin [x] 287 Install Tray [x] 287 Insufficient memory for Flash
[54] 291 Non‑Lexmark [supply type], see
User’s Guide [33.xy] 291 Not enough free space in flash
memory for resources [52] 292 Paper changes needed 292 Parallel port [x] disabled
mismatch [41.xy] 282 Change [paper source] to
[custom string] load [orientation] 282 Change [paper source] to
Memory Defragment operation [37] 287 Insufficient memory to collate
[56] 292 Printer had to restart. Last job
[custom type name] load [orientation] 282 Change [paper source] to
job [37] 288 Insufficient memory to support
may be incomplete. 292 Reattach bin [x] 293 Reattach bins [x] – [y] 293 Reinstall missing or
Resource Save feature [35] 288 Insufficient memory, some Held
[paper size] load [orientation] 282
Jobs were deleted [37] 287
unresponsive cartridge [31.xy] 294
Index 358 · printer · Cartridge, imaging unit




printing from a Macintosh
computer 167 printing from Windows 167 verifying printer setup 40 vertical voids appear 336 virtual display
checking, using Embedded Web
Server 120, 168 voids appear 336 volatile memory 78, 125, 174
erasing 79, 126, 175 volatility
statement of 78, 125, 174
W wiping printer hard disk 80 wiping the printer hard disk 127, 176 Wireless menu 206 wireless network
configuration information 36 wireless network setup
using the Embedded Web
Server 39 wireless setup wizard
Index 362 · using 37
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.