
User's Guide
Machine type(s):
Model(s):
410, 430


Conventions
Different types of caution statements include:
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Safety information 8

CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a service representative.
Safety information 9

SAVE THESE INSTRUCTIONS.
Safety information 10

Learning about the printer 11
Finding information about the printer

Learning about the printer 12
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, then leave enough room for them also. It is important to:

Learning about the printer 13

1 Right side 102 mm (4 in.)
2 Front 508 mm (20 in.)
3 Left side 152 mm (6 in.)
4 Rear 102 mm (4 in.)
5 Top 254 mm (10 in.)

Learning about the printer 14

4 5 6 3 4 5 3 4

5 Optional 650-sheet duo tray with integrated multipurpose feeder (Tray 2)

8 7 6 9 10


Learning about the printer 15

3 Arrow buttons Scroll through menus, or settings on the display.
5 Sleep button Enable Sleep mode or Hibernate mode.
9 Indicator light Check the status of the printer.
10 Front USB port Connect a camera or flash drive to the printer.
The colors of the Sleep button and indicator lights on the control panel signify a printer status or condition.

Off The printer is off or in Hibernate mode.
Blinking green The printer is warming up, processing data, or printing.
Off The printer is off, idle, or in Ready state.
Blinking amber The printer is entering or waking from Hibernate mode.
Blinking amber for 0.1 second, then goes completely off for 1.9 seconds in a slow, pulsing pattern

Learning about the printer 16
If the printer is installed on a network, then you can use the Embedded Web Server to do the following:
To access the Embedded Web Server for your printer:
– An IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. – If you are using a proxy server, then temporarily disable it to load the Web page correctly.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
The Embedded Web Server page appears.

Additional printer setup 17
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
You can customize your printer connectivity and memory capacity by adding optional cards.
* This internal option is available only in CS510 printer model.

Additional printer setup 18
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board at the back of the printer.
2 Turn the screws counterclockwise to remove them.

3 Slightly open the controller board access cover, and then shift to the right to remove it.

4 Locate the appropriate connector on the controller board.

Additional printer setup 19

1 Memory card connector
2 Option card connector
5 Reattach the cover.


Additional printer setup 20
6 Turn the screws clockwise to lock the cover.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 18.
2 Unpack the memory card.

Additional printer setup 21
3 Align the notch (1) on the memory card with the ridge (2) on the connector.

4 Push the memory card straight into the connector, and then push the card toward the controller board wall until it clicks into place.

5 Close the controller board access cover.

Additional printer setup 22
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the controller board.
For more information, see “Accessing the controller board” on page 18.
2 Unpack the optional card.
3 Holding the card by its sides, align the plastic pins (1) on the card with the holes (2) on the controller board.



Additional printer setup 23
4 Push the card firmly into place as shown in the illustration.

5 Close the controller board access door.

Additional printer setup 24
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Install the printer and any optional tray in the following order:
The printer supports two optional input sources: a 550‑sheet tray (Tray 3) and a 650‑sheet duo tray (Tray 2) with an integrated multipurpose feeder.
CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Unpack the optional tray and the dust cover, and then remove all packing material.

2 Place the tray near the printer.
3 Align the 650‑sheet duo tray with the 550‑sheet tray, and then lower it into place.

Additional printer setup 25

4 Align the printer with the 650‑sheet duo tray, and then lower the printer into place.

5 Install the dust covers.



Additional printer setup 26
Connect the printer to the computer using a USB cable or to the network using an Ethernet cable.
Make sure to match the following:

1 USB printer port Connect the printer to a computer.
2 Ethernet port Connect the printer to a network.
3 USB port Attach an optional wireless network adapter.
4 Printer power cord socket Connect the printer to a properly grounded electrical outlet.
2 Run the installer, and then follow the instructions on the computer screen.
Use the To

Additional printer setup 27
3 For Macintosh users, add the printer.
1 Open the printers folder.
3 Navigate to the Configuration tab, and then select Update Now ‑ Ask Printer.
4 Apply the changes.
1 From System Preferences in the Apple menu, navigate to your printer, and then select Options & Supplies.
2 Navigate to the list of hardware options, and then add any installed options.
3 Apply the changes.
To configure your printer to connect to an Ethernet network, organize the following information before you begin:

Additional printer setup 28
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.
Make sure you have the following information before setting up the printer on a wireless network:
Some ad hoc networks will also require the automatic setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are four basic options for Security Method: – WEP key
If your network uses more than one WEP key, then enter up to four in the provided spaces. Select the key currently in use on the network by selecting the default WEP transmit key. – WPA or WPA2 preshared key or passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – 802.1X–RADIUS
If you are installing the printer on an 802.1X network, then you may need the following:
If your wireless network does not use any type of security, then you will not have any security information.
– If you do not know the SSID of the network that your computer is connected to, then launch the wireless
utility of the computer network adapter, and then look for the network name. If you cannot find the SSID or the security information for your network, then see the documentation that came with the access point, or contact your system support person. – To find the WPA/WPA2 preshared key or passphrase for the wireless network, see the documentation
that came with the access point, see the Embedded Web Server associated with the access point, or consult your system support person.

Additional printer setup 29
Before you begin, make sure that:
> Settings > > Network/Ports > > Active NIC > > Auto >
1 From the printer control panel, navigate to:
> Settings > > Network/Ports > > Network [x] > > Network [x] Setup > > Wireless >
> Wireless Connection Setup >
2 Select a wireless connection setup.
Search for networks Show available wireless connections.
Enter a network name Manually type the SSID.
Wi‑Fi Protected Setup Connect the printer to a wireless network using Wi‑Fi Protected Setup.
3 Press , and then follow the instructions on the printer display.
Before you begin, make sure that:
1 From the printer control panel, navigate to:
> Settings > > Network/Ports > > Network [x] > > Network [x] Setup > > Wireless >
> Wireless Connection Setup > > Wi‑Fi Protected Setup > > Start Push Button Method >
2 Follow the instructions on the printer display.
Use To

Additional printer setup 30
1 From the printer control panel, navigate to:
> Settings > > Network/Ports > > Network [x] > > Network [x] Setup > > Wireless >
> Wireless Connection Setup > > Wi‑Fi Protected Setup > > Start PIN Method >
2 Copy the eight‑digit WPS PIN.
3 Open a Web browser, and then type the IP address of your access point in the address bar.
4 Access the WPS settings. For more information, see the documentation that came with your access point.
5 Enter the eight‑digit PIN, and then save the setting.
Before you begin, make sure that:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Network/Ports > Wireless.
3 Modify the settings to match the settings of your access point (wireless router).
4 Click Submit.
5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on.
6 To verify if your printer is connected to the network, print a network setup page. Then in the Network Card [x] section, see if the status is Connected.

Additional printer setup 31
Print a menu settings page to review the current menu settings and to verify if the printer options are installed correctly.
From the printer control panel, navigate to:
> Settings > > Reports > > Menu Settings Page >
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the printer control panel, navigate to:
> Settings > > Reports > > Network Setup Page >
2 Check the first section of the network setup page, and then confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult your system support person for a solution, and then print another network setup page.

Loading paper and specialty media 32
The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 137 and “Storing paper” on page 49.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Paper Size/Type >
2 Press the up or down arrow button to select the tray or feeder size, and then press .
3 Press the up or down arrow button to select the paper size, and then press .
4 Press the up or down arrow button to select the tray or feeder type, and then press .
5 Press the up or down arrow button to select the paper type, and then press .
The Universal paper size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus.
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Universal Setup > > Units of Measure > > select a unit
2 Press the up or down arrow button until Portrait Height or Portrait Width appears, and then press
3 Enter the preferred settings using the keypad or press the left or right arrow button to manually select the
size you want, and then press .
4 Press .
of measure >

Loading paper and specialty media 33
The printer has one 250-sheet tray (Tray 1) with an integrated manual feeder. The 250-sheet tray, the 650-sheet duo tray, and the 550-sheet tray support the same paper sizes and types and are loaded in the same way.
1 Pull out the tray completely.

2 If the paper is longer than letter‑size paper, then squeeze and then slide the length guide at the back of the tray to extend it.


Loading paper and specialty media 34
3 Squeeze, and then slide the length guide tab to the correct position for the size of the paper being loaded.


4 Squeeze, and then slide the width guide tab to the correct position for the size of the paper being loaded.


5 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.


Loading paper and specialty media 35
6 Load the paper stack with the recommended printable side faceup.

7 Place the paper guides securely against the edges of the paper.
8 Insert the tray.

9 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
The 650‑sheet duo tray (Tray 2) consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The tray is loaded in the same way as the 250‑sheet tray and supports the same paper types and sizes. The only differences are the look of the guide tabs and the location of the paper size indicators.

Loading paper and specialty media 36

1 Length guide tab
2 Paper size indicator
3 Width guide tab
1 Push the multipurpose feeder latch to the left.



Loading paper and specialty media 37
2 Open the multipurpose feeder.

3 Pull the multipurpose feeder extender.

4 Prepare the paper for loading. • Flex the sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.


Loading paper and specialty media 38
5 Locate the maximum paper fill indicator and tab.


6 Load the paper, and then adjust the width guide to lightly touch the edge of the paper stack. • Load paper, card stock, and transparencies with the recommended printable side facedown and the top edge entering the printer first.


Loading paper and specialty media 39

7 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
The standard 250‑sheet tray has an integrated manual feeder that can be used to print on different types of paper one sheet at a time.
One‑sided printing using a letterhead Two‑sided printing using a letterhead

ABC

Loading paper and specialty media 40

2 Feed paper into the manual feeder only to the point where its leading edge can contact the paper guides.
3 Adjust the paper guides to the width of the paper loaded.

The printer links trays when the specified paper size and type are the same. When a linked tray becomes empty, paper feeds from the next linked tray. To prevent trays from linking, assign a unique custom paper type name.
1 Open a Web browser, and then type the printer IP address in the address field.

Loading paper and specialty media 41
2 Click Settings > Paper Menu.
4 Click Submit.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Names.
3 Select a custom name, and then type a new custom paper type name.
4 Click Submit.
5 Click Custom Types, and then verify if the new custom paper type name has replaced the custom name.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Paper Menu > Custom Types.
3 Select a custom paper type name, and then select a paper type.
4 Click Submit.

Loading paper and specialty media 42
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Custom Types
2 Select a custom paper type name, and then select a paper type.
3 Press .

Paper and specialty media guide 43
Source Printing Printable side
One‑sided Faceup Load the sheet with the top edge entering the printer first.

Two‑sided Facedown Load the sheet with the bottom edge entering the printer first.
Paper orientation · Trays · Trays

Paper and specialty media guide 44
Source Printing Printable side
One‑sided Facedown Load the sheet with the top edge entering the printer first.

Two‑sided Faceup Load the sheet with the bottom edge entering the printer first.
One‑sided Facedown Load the sheet with the top edge entering the printer first.

Paper and specialty media guide 45
Source Printing Printable side
Two‑sided Faceup Load the sheet with the bottom edge entering the printer first.

Print a test page on the transparencies being considered for use before buying large quantities.
Paper orientation · Multipurpose feeder

Paper and specialty media guide 46
Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly affect print quality.
Selecting the correct paper or specialty media reduces printing problems. For the best print quality, try a sample of the paper or specialty media before buying large quantities.
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.

Paper and specialty media guide 47
The printer trays can automatically feed paper weights up to 176‑g/m2 (47‑lb) bond grain long paper. The multipurpose feeder can automatically feed paper weights up to 176‑g/m2 (47‑lb) bond grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75‑g/m2 (20‑lb) bond grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 inches), we recommend 90 g/m2 (24 lb) or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, then toner cannot fuse to it properly. If paper is too smooth, then it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; smoothness between 150 and 250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time to several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60–90‑g/m2 (16–24‑lb) bond paper, grain long paper is recommended.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
The following paper types are not recommended for use with the printer:

Paper and specialty media guide 48
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid paper jams and poor print quality:
Use these guidelines when selecting preprinted forms and letterhead:
Use inks that are not affected by the resin in toner. Inks that are oxidation‑set or oil‑based generally meet these requirements; latex inks might not.
When in doubt, contact your paper supplier.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser (electrophotographic) printers. In 1998, Lexmark presented to the US government a study demonstrating that recycled paper produced by major mills in the US fed as well as non-recycled paper. However, no blanket statement can be made that all recycled paper will feed well.
Lexmark consistently tests its printers with recycled paper (20–100% post-consumer waste) and a variety of test paper from around the world, using chamber tests for different temperature and humidity conditions. Lexmark has found no reason to discourage the use of today's recycled office papers, but generally the following property guidelines apply to recycled paper.

Paper and specialty media guide 49
Recycled paper, paper of lower weight (
Use these paper storage guidelines to help avoid jams and uneven print quality:
The following tables provide information on standard and optional paper sources and the sizes, types, and weights of paper they support.
Note: Your printer model may have a 650‑sheet duo tray, which consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The 550‑sheet tray of the 650‑sheet duo tray supports the same paper sizes as the optional 550‑sheet tray. The integrated multipurpose feeder supports different paper sizes, types, and weights.

Paper and specialty media guide 50
Paper size and dimension
Standard 250‑sheet tray Manual
650‑sheet duo tray 550‑sheet tray
550‑sheet tray Multipurpose
1
210 x 297 mm (8.3 x 11.7 in.)
1 2 1 2 X
148 x 210 mm (5.83 x 8.3 in.)
X X 1 X X
105 x 148 mm (4.1 x 5.8 in.)
1 1 1 1 X
182 x 257 mm (7.2 x 10.1 in.)
Letter 216 x 279 mm (8.5 x 11 in.)
1
Legal 216 x 356 mm (8.5 x 14 in.)
1
184 x 267 mm (7.3 x 10.5 in.)
1
216 x 340 mm (8.5 x 13.4 in.)
1
216 x 330 mm (8.5 x 13 in.)
140 x 216 mm (5.5 x 8.5 in.)
1 The paper source supports paper size without size sensing.
2 Universal is only supported in the standard 250and optional 550sheet tray if the paper size is from 148 x 215.9 mm (5.83 x 8.5 inches) to 215.9 x 355.6 mm (8.5 x 14 inches).
3Universal is only supported in the multipurpose feeder and manual feeder if the paper size is from 76.2 x 127 mm (3 x 5 inches) to 215.9 x 359.9 mm (8.5 x 14.17 inches).
4Universal is only supported in duplex mode if the width is between 210 mm (8.27 inches) and 215.9 mm (8.5 inches) and length is between 279.4 mm (11 inches) and 355.6 mm (14 inches).

Paper and specialty media guide 51
Paper size and dimension
Standard 250‑sheet tray Manual
650‑sheet duo tray 550‑sheet tray
550‑sheet tray Multipurpose
76 x 127 mm (3 x 5 in.) to 216 x 356 mm (8.5 x 14 in.)
1,2 1,2 1,2 4
148 x 210 mm (5.8 x 8.3 in) to 216 x 356 mm (8.5 x 14 in).
7 3/4 Envelope (Monarch)
98 x 191 mm (3.9 x 7.5 in.)
98 x 225 mm (3.9 x 8.9 in.)
105 x 241 mm (4.1 x 9.5 in.)
110 x 220 mm (4.3 x 8.7 in.)
162 x 229 mm (6.4 x 9 in.)
176 x 250 mm (6.9 x 9.8 in.)
98 x 162 mm (3.9 x 6.3 in.) up to 176 x 250 mm (6.9 x 9.8 in.)
1 The paper source supports paper size without size sensing.
2 Universal is only supported in the standard 250and optional 550sheet tray if the paper size is from 148 x 215.9 mm (5.83 x 8.5 inches) to 215.9 x 355.6 mm (8.5 x 14 inches).
3Universal is only supported in the multipurpose feeder and manual feeder if the paper size is from 76.2 x 127 mm (3 x 5 inches) to 215.9 x 359.9 mm (8.5 x 14.17 inches).
4Universal is only supported in duplex mode if the width is between 210 mm (8.27 inches) and 215.9 mm (8.5 inches) and length is between 279.4 mm (11 inches) and 355.6 mm (14 inches).

Paper and specialty media guide 52

650‑sheet duo tray 550‑sheet tray

Printing a document
1 From the document that you are trying to print, open the Print dialog.
2 If necessary, adjust the settings.
3 Send the print job.
From the printer control panel, navigate to:
> Settings > > Settings > > Print Settings > > Quality Menu > > Print Mode > > Black
1 Open a Web browser, and then type the IP address of the printer in the address field.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness, and then click Submit.
1 From the printer control panel, navigate to:
> Settings > > Settings > > Print Settings > > Quality Menu > > Toner Darkness
2 Adjust the toner darkness, and then press .
Printing 53 · Only >

Max Speed and Max Yield let you choose between a faster print speed and a higher toner yield. Max Yield is the factory default setting.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Setup Menu.
3 From the Printer Usage list, select Max Speed or Max Yield.
4 Click Submit.
1 From the printer control panel, navigate to:
> Settings > > Settings > > Print Settings > > Setup Menu > > Printer Usage >
2 Select Max Speed or Max Yield, and then press .
Printing 54

1 Insert a flash drive into the USB port.

Printing 55

2 From the printer control panel, select the document you want to print.
3 Press the left or right arrow button to specify the number of copies for printing, and then press .
Recommended flash drives File type
Documents:
Images:
Mopria® Print Service is a mobile printing solution for mobile devices running on Android version 4.4 or later. It allows you to print directly to any Mopria‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Tap Print, and then select the printer.
Printing 56

3 Send the print job.
Google Cloud PrintTM is a mobile printing service that allows enabled applications on mobile devices to print to any Google Cloud Print‑ready printer.
1 From the home screen of your mobile device, launch an enabled application.
2 Tap Print, and then select the printer.
3 Send the print job.
AirPrint is a mobile printing solution that allows you to print directly from Apple devices to an AirPrint‑certified printer.
1 From the home screen of your mobile device, launch a compatible application.
2 Select an item to print, and then tap the share icon.
3 Tap Print, and then select a printer.
4 Print the document.
LexmarkTM Mobile Print allows you to send documents and images directly to a supported Lexmark printer.
1 Open the document, and then send or share the document to Lexmark Mobile Print.
2 Select a printer.
3 Print the document.
1 From the printer control panel, navigate to:
> Settings > > Security > > Confidential Print > select the print job type
Printing 57

Print job type Description
Max Invalid PIN Limits the number of times an invalid PIN can be entered.
Confidential Job Expiration Lets you hold print jobs in the computer until you enter the PIN from the printer control panel.
Repeat Job Expiration Lets you print and store print jobs in the printer memory for reprinting.
Verify Job Expiration Lets you print one copy of a print job while the printer holds the remaining copies. It allows you to examine if the first copy is satisfactory. The print job is automatically deleted from the printer memory once all copies are printed.
Reserve Job Expiration Lets you store print jobs for printing at a later time. The print jobs are held until deleted from the Held Jobs menu.
2 Press .
1 From the document you are trying to print, open the Print dialog.
3 Select the print job type.
4 If necessary, assign a user name.
5 Send the print job.
6 From the printer home screen, select Held Jobs.
7 Send the print job.
Printing 58

1 From the printer control panel, navigate to:
> Settings > > Reports > > Print Fonts
2 Press the up or down arrow button to select the font setting.
3 Press .
From the printer control panel, navigate to:
> Settings > > Reports > > Print Directory >
1 From the printer control panel, press .
2 When a list of print jobs appears, select the job to cancel, and then press .
3 Press to go back to the home screen.
2 Select the print job to cancel.
Printing 59

Understanding the printer menus 60
Menus list
Supplies Paper Menu Reports Network/Ports
Magenta Cartridge Yellow Cartridge
Device Statistics Network Setup Page
Standard Network or Network [x] Standard USB
Black Cartridge Waste Toner Bottle
Network [x] Setup Page
Paper Texture Paper Weight
Black or Color Imaging Kit
Security Settings Help Option Card Menu
Erase Temporary Data Files Security Audit Log
Print Quality Printing Guide
Set Date and Time
1 This menu item appears only when a 650-sheet duo tray is attached.
Cyan Cartridge View the status of the toner cartridges, which can be any of the following:
Early Warning Low Invalid Near End of Life Replace Missing Defective OK Unsupported

Understanding the printer menus 61
View the status of the waste toner bottle.
Near Full Replace Missing OK
View the status of the imaging kit.
OK Replace Black Imaging Kit Replace Color Imaging Kit
View the status of the maintenance kit.
Set a default paper source for all print jobs.
Tray [x] MP Feeder Manual Paper Manual Envelope
Specify the size of the paper loaded in each tray.
A4 A5 JIS‑B5 Letter Legal Executive Oficio (Mexico) Folio Universal

Understanding the printer menus 62
Specify the type of the paper loaded in each tray.
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the size of the paper loaded in the multipurpose feeder.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Use To · Tray [x] Type · Multipurpose Feeder Size

Understanding the printer menus 63
Specify the type of the paper loaded in the multipurpose feeder.
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]
Specify the size of the paper being manually loaded.
A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal
Specify the type of the paper being manually loaded.
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x]

Understanding the printer menus 64
Specify the size of the envelope being manually loaded.
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope
Specify the type of the envelope being manually loaded.
Envelope Custom Type [x]
Determine when the printer selects paper from the multipurpose feeder.
Substitute a specified paper size if the requested paper size is not available.
Off Statement/A5 Letter/A4 All Listed

Understanding the printer menus 65
Specify the relative texture of the plain paper loaded.
Specify the relative texture of the card stock loaded.
Specify the relative texture of the transparencies loaded.
Specify the relative texture of the recycled paper loaded.
Specify the relative texture of the glossy paper loaded.
Specify the relative texture of the labels loaded.
Specify the relative texture of the bond paper loaded.
Specify the relative texture of the envelopes loaded.
Specify the relative texture of the letterhead loaded.
Specify the relative texture of the preprinted paper loaded.

Understanding the printer menus 66
Specify the relative texture of the colored paper loaded.
Specify the relative texture of the light paper loaded.
Specify the relative texture of the heavy paper loaded.
Specify the relative texture of the cotton paper loaded.
Specify the relative texture of the custom paper loaded.
Specify the relative weight of the plain paper loaded.
Specify the relative weight of the card stock loaded.
Specify the relative weight of the transparencies loaded.
Specify the relative weight of the recycled paper loaded.

Understanding the printer menus 67
Specify the relative weight of the glossy paper loaded.
Specify the relative weight of the labels loaded.
Specify the relative weight of the bond paper loaded.
Specify the relative weight of the envelope loaded.
Specify the relative weight of the letterhead loaded.
Specify the relative weight of the preprinted paper loaded.
Specify the relative weight of the colored paper loaded.
Specify that the relative weight of the paper loaded is light.
Specify that the relative weight of the paper loaded is heavy.
Specify the relative weight of the rough or cotton paper loaded.
Specify the relative weight of the custom paper loaded.

Understanding the printer menus 68
Determine and set two‑sided printing for all print jobs that specify Recycled as the paper type.
Determine and set two‑sided printing for all print jobs that specify Glossy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Bond as the paper type.
Determine and set two‑sided printing for all print jobs that specify Letterhead as the paper type.
Determine and set two‑sided printing for all print jobs that specify Preprinted as the paper type.
Determine and set two‑sided printing for all print jobs that specify Colored as the paper type.
Determine and set two‑sided printing for all print jobs that specify Light as the paper type.
Determine and set two‑sided printing for all print jobs that specify Heavy as the paper type.
Determine and set two‑sided printing for all print jobs that specify Custom [x] as the paper type.

Understanding the printer menus 69
Associate a paper or specialty media type with a factory default Custom Type [x] name or a user‑defined custom name created in the Embedded Web Server or MarkVisionTM Professional.
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope
Specify a paper type when Recycled is selected.
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope
Identify the units of measure.
Set the portrait width.
3–14.17 inches 76–360 mm
Set the portrait height.
3–14.17 inches 76–360 mm

Understanding the printer menus 70
Specify the feed direction if the paper can be loaded in either direction.
Short Edge Long Edge
Menu Settings Page Print a report containing information about paper loaded in trays, installed memory, the total page count, alarms, timeouts, the printer control panel language, the TCP/IP address, the status of supplies, the status of the network connection, and other information.
Device Statistics Print a report containing printer statistics such as supply information and details about printed pages.
Network Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
Network [x] Setup Page Print a report containing information on network printer settings, such as the TCP/IP address information.
Profiles List Print a list of profiles stored in the printer.
Print a report in English of all the fonts available for the printer language currently set in the printer.
PCL Fonts PostScript Fonts
Print demo files that are available in the RIP code, the flash option, and the disk option.
Demo Page [list of available demo pages]
Asset Report Print a report containing asset information including the printer serial number and model name. The report contains text and UPC bar codes that can be scanned into an asset database.
![Page 71 of the Lexmark CS417dn user manual — Standard Network or Network [x] menu](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-71.webp?w=400)
Understanding the printer menus 71
Auto [list of available network cards]
Reduce power consumption when the printer receives no data from the Ethernet network.
Set the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language.
Set the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.

Understanding the printer menus 72
Set the size of the network input buffer.
Auto 3KB to [maximum size allowed]
Temporarily store print jobs in the printer hard disk before printing. This menu only appears when a formatted disk is installed.
Set the printer to process Macintosh binary PostScript print jobs.
Standard Network Setup OR Network [x] Setup
Show and set the printer network settings.
Reports Network Card TCP/IP IPv6 Wireless AppleTalk
To access the menu, navigate to either of the following:
Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP
address.

Understanding the printer menus 73
To access the menu, navigate to either of the following:
View the connection status of the wireless network adapter.
View Card Speed View the speed of an active wireless network adapter.
Reduce power consumption when the printer receives no data from the Ethernet network.
View the network addresses.
0, 10–225 seconds Set the amount of time it takes for a network print job to be canceled.
Allow the printer to print a banner page.
To access the menu, navigate to either of the following:
Set Hostname Set the current TCP/IP hostname.
IP Address View or change the current TCP/IP address.
Netmask View or change the current TCP/IP netmask.
Gateway View or change the current TCP/IP gateway.

Understanding the printer menus 74
Specify the DHCP address and parameter assignment.
Specify the RARP address assignment setting.
Specify the BOOTP address assignment setting.
Specify the Zero Configuration Networking setting.
Send files to the printer using the built‑in FTP server.
Enable the built-in Web server (Embedded Web Server) which lets you monitor and manage the printer remotely using a Web browser.
WINS Server Address View or change the current WINS server address.
View or change the current DDNS setting.
View or change the current mDNS setting.
DNS Server Address View or change the current DNS server address.
Backup DNS Server Address [x] View or change the current DNS server address.
View or change the current HTTPS setting.
To access the menu, navigate to any of the following:

Understanding the printer menus 75
Enable IPv6 in the printer.
Specify whether or not the network adapter accepts the automatic IPv6 address configuration entries provided by a router.
Set Hostname Set the host name.
Enable DHCPv6 in the printer.
To access the menu, navigate to:
Wi‑Fi Protected Setup (WPS)
Establish a wireless network and enable network security.
Start Push Button Method Start PIN Method
Enable/Disable WPS Auto‑detection
Automatically detect the connection method that an access point with WPS uses—Start Push Button Method or Start PIN Method.
Specify the network mode.
Specify the wireless standard for the wireless network.
802.11b/g 802.11b/g/n

Understanding the printer menus 76
Choose Network Select an available network for the printer to use.
View Signal Quality View the quality of the wireless connection.
View Security Mode View the encryption method for the wireless network.
To access the menu, navigate to either of the following:
Enable or disable AppleTalk support.
View Name Show the assigned AppleTalk name.
View Address Show the assigned AppleTalk address.
Provide a list of AppleTalk zones available on the network.
[list of zones available on the network]
Set the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language.

Understanding the printer menus 77
Set the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language.
Set the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol.
Set the size of the USB input buffer.
Disabled Auto 3K to [maximum size allowed]
Set the printer to process Macintosh binary PostScript print jobs.
Set the network address, netmask, and gateway information for an external print server.
yyy.yyy.yyy.yyy
yyy.yyy.yyy.yyy
yyy.yyy.yyy.yyy

Understanding the printer menus 78
Primary SMTP Gateway Specify SMTP server gateway and port information.
Secondary SMTP Gateway Port
5–30 Specify the amount of time in seconds before the server stops trying to send an e‑mail.
Reply Address Specify a reply address of up to 128 characters in the e-mail sent by the printer.
Set the printer to use SSL for increased security when connecting to the SMTP server.
Specify the type of user authentication required for printing privileges.
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specify what credentials will be used when communicating to the SMTP server. Some SMTP servers require credentials to send an e- mail.
None Use Device SMTP Credentials

Understanding the printer menus 79
Limit the number of times an invalid PIN can be entered.
Limit the amount of time a confidential print job stays in the printer before it is deleted.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs needing verification.
Off 1 hour 4 hours 24 hours 1 week
Set a time limit on how long the printer stores print jobs for printing at a later time.
Off 1 hour 4 hours 24 hours 1 week
Erase Temporary Data Files deletes only print job data on the printer hard disk that are not currently in use by the file system. All permanent data on the printer hard disk are preserved, such as downloaded fonts, macros, and held jobs.

Understanding the printer menus 80
Specify the mode for erasing temporary data files.
Mark all disk space used by a previous print job. This method does not permit the file system to reuse this space until it has been cleared.
Single pass Multiple pass
Export Log Let an authorized user export the audit log.
Specify whether or not audit logs are deleted.
Specify how and whether or not audit logs are created.
Yes No Enable Remote Syslog
No Yes Remote Syslog Facility
0–23 Severity of Events to Log
Current Date and Time View the current date and time settings for the printer.

Understanding the printer menus 81
Manually Set Date and Time Enter the date and time.
Time Zone Select the time zone.
Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting.
Enable Network Time Protocol, which synchronizes the clocks of devices on a network.
Set the language of the text appearing on the display.
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portugues Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese

Understanding the printer menus 82
View the estimates of the supplies on the control panel, Embedded Web Server, menu settings, and device statistics reports.
Show estimates Do not show estimates
Minimize the use of energy, paper, or specialty media.
Off Energy Energy/Paper Paper
Minimize the printer noise.
Run the setup wizard.
Specify a language and custom key information for the display keyboard.
English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portugues Russian Polski Swiss German Swiss French Korean Magyar Turkce Cesky Simplified Chinese Traditional Chinese Japanese Custom Key [x]

Understanding the printer menus 83
Specify the unit of measurement for paper sizes.
U.S. Metric
Specify what is displayed on the upper corners of the home screen.
Left Side Right Side Custom Text [x]
For Left side and Right side, select from the following options:
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Custom Text [x] Model Name
Customize the displayed information for the supplies.
Black Toner Cyan Toner Magenta Toner Yellow Toner Waste Toner Bottle Fuser Transfer Module
Select from the following options:
Do not display Display Message to display

Understanding the printer menus 84
Customize the displayed information for certain menus.
Paper Jam Load Paper Service Errors
Select from the following options:
Yes No Message to display
Change the icons that appear on the home screen.
Change Language Search Held Jobs Held Jobs USB Drive Profiles and Apps Bookmarks Jobs by User Forms and Favorites Background and Idle Screen Eco-Settings
For each icon, select from the following options:
Display Do Not display
Format the date.
MM‑DD‑YYYY DD‑MM‑YYYY YYYY‑MM‑DD
Format the time.
12 hour A.M./P.M. 24 hour clock
20–100 Specify the brightness of the display.
Set the audio volume for the buttons.

Understanding the printer menus 85
Specify whether bookmarks are displayed from the Held Jobs area.
Web Page Refresh Rate
30–300 Specify the number of seconds between Embedded Web Server refreshes.
Contact Name Specify a contact name.
Location Specify the location.
Set an alarm when the printer requires user intervention.
Alarm Control Cartridge Alarm
For each alarm type, select from the following options:
Set the amount of time in minutes before the printer enters a lower power state.
Set the amount of time in minutes the printer waits after a job is printed before it goes into a reduced power state.
Print a job with the display turned off.
Print with Display Off
Allow printing with display off Display on when printing

Understanding the printer menus 86
Set the amount of time the printer waits before it enters Hibernate mode.
Disabled 20 minutes 1–3 hours 6 hours 1–3 days 1–2 weeks 1 month
Hibernate Timeout on Connection
Set the printer to Hibernate mode even if there is an active Ethernet connection.
Hibernate Do Not Hibernate
Set the amount of time in seconds before returning the control panel to a Ready state.
Set the amount of time in seconds the printer waits to receive an end‑of‑job message before canceling the rest of the print job.
Set the amount of time in seconds the printer waits for additional data before canceling a print job.
Set the amount of time the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue.

Understanding the printer menus 87
Set the printer to restart when an error occurs.
Reboot when idle Reboot always Reboot never
Determine the number of automatic reboots the printer can perform.
Let the printer automatically continue printing from certain offline situations when these are not resolved within the specified time period.
Specify whether the printer reprints jammed pages.
Successfully print a page that may not have printed otherwise.
Set the printer to continue a specified job without returning to the home screen when the screen timeout timer expires.
Determine how the printer, while in idle state, reacts to a short press of the Sleep button.
Do Nothing Sleep Hibernate

Understanding the printer menus 88
Press and Hold Sleep Button
Determine how the printer, while in idle state, reacts to a long press of the Sleep button.
Do Nothing Sleep Hibernate
Use the printer factory default settings.
Do Not Restore Restore Now
Export configuration files to a flash drive.
Set the default printer language.
PCL Emulation PS Emulation
Set the logical and physical printable area.
Normal Fit To Page Whole Page
Set color toner use in printing.
Max Yield Max Speed
Set the printer to print text and graphics using only the black toner cartridge.

Understanding the printer menus 89
Specify how the printer handles temporary downloads, such as fonts and macros stored in the RAM, when the printer receives a job that requires more than the available memory.
Specify the order in which confidential and held jobs are printed when Print All is selected.
Alphabetical Oldest First Newest First
Specify whether two‑sided printing is set as the default for all print jobs.
1 sided 2 sided
Define the way two‑sided pages are bound and printed.
Long Edge Short Edge
1–999 Specify the default number of copies for each print job.
Specify whether blank pages are inserted in a print job.
Do Not Print Print
Stack the pages of a print job in sequence when printing multiple copies.
(1,1,1) (2,2,2) (1,2,3) (1,2,3)
Specify whether blank separator sheets are inserted.
Off Between Copies Between Jobs Between Pages

Understanding the printer menus 90
Specify the paper source for the separator sheet.
Tray [x] MP Feeder
Print multiple pages on a single sheet of paper.
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specify the order in which pages are printed on a single sheet when using Paper Saver.
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specify the orientation in which pages are printed on a single sheet.
Print a border when using Paper Saver.
Specify whether images are printed in black and white or in color.

Understanding the printer menus 91
Adjust the color output on the printed page.
Specify the printed output resolution in dots per inch or in color quality (CQ).
1200 dpi 4800 CQ
1–5 Lighten or darken the printed output.
Enable a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts.
Click File > Print, and then click Properties, Preferences, Options, or Setup. For Macintosh users:
Choose File > Print, and then adjust the settings from the Print dialog and pop‑up menus.
Reduce the amount of toner used for graphics and images. The amount of toner used for text is not reduced.
Adjust the printed output either by lightening or darkening it. You can conserve toner by lightening the output.
‑6 to 6
0–5 Adjust the contrast of printed objects.

Understanding the printer menus 92
0–5 Adjust saturation in color outputs.
Adjust color in printed output by increasing or decreasing the amount of toner being used for each color.
‑5 to 5 Magenta
‑5 to 5 Yellow
‑5 to 5 Black
‑5 to 5 Reset Defaults
Print sample pages for each of the RGB and CMYK color conversion tables used in the printer.
sRGB Display sRGB Vivid Display—True Black Vivid Off—RGB US CMYK Euro CMYK Vivid CMYK Off—CMYK
Customize the RGB color conversions.
RGB Image RGB Text RGB Graphics
Select from the following options:
Vivid sRGB Display Display—True Black sRGB Vivid Off

Understanding the printer menus 93
Customize the CMYK color conversions.
CMYK Image CMYK Text CMYK Graphics
Select from the following options:
US CMYK Euro CMYK Vivid CMYK Off
Spot Color Replacement Assign specific CMYK values to named spot colors.
Color Adjust Initiate a recalibration of color conversion tables and allow the printer to make adjustments for color variations in output.
Format the flash memory.

Understanding the printer menus 94
Activate Hex Trace Assist in isolating the source of a print job problem.
Provide an estimate of the percentage coverage of toner on a page. The estimate is printed on a separate page at the end of each print job.
Print a page containing information on errors, including XML markup errors.
Scale page content to fit the selected paper size.
Print annotations in a PDF.
Do Not Print Print
Print a page containing the PostScript error.
Lock PS Startup Mode
Allow users to disable the SysStart file.
Enhance the contrast and sharpness of low‑resolution images and smoothen their color transitions.

Understanding the printer menus 95
Specify the set of fonts used by the Font Name menu.
Resident Disk Download Flash All
Identify a specific font and the option where it is stored.
Specify the symbol set for each font name.
Change the point size for scalable typographic fonts.
1.00–1008.00
Specify the font pitch for scalable monospaced fonts.
0.08–100

Understanding the printer menus 96
Specify the orientation of text and graphics on the page.
Specify the number of lines that print on each page.
Set the printer to print on A4‑size paper.
198 mm 203 mm
Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Auto CR after LF
Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.
Auto LF after CR

Understanding the printer menus 97
Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Env
Display the factory default setting assigned to each tray or feeder.
MPF Default = 8 T1 Default = 1 T1 Default = 4 T1 Default = 5 T1 Default = 20 T1 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Restore all tray and feeder assignments to the factory default settings.
Sets the orientation of the text and graphics on the page

Understanding the printer menus 98
1–255 Sets the number of lines that print on each page
0.25–30.00 Sets the number of lines that print per inch
Sets the logical and physical printable area of the page
Specifies a default character set for PPDS print jobs
Replaces a missing font with a similar font
Configures the printer to work with printer software or programs that use different source assignments for trays, drawers, and feeders
Auto CR after LF
Specifies whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command

Understanding the printer menus 99
Auto LF after CR
Specifies whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSansMTKO
Set the default font for HTML documents.
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers
1–255 pt Set the default font size for HTML documents.

Understanding the printer menus 100
1–400% Scale the default font for HTML documents.
Set the page orientation for HTML documents.
8–255 mm Set the page margin for HTML documents.
Specify whether to print backgrounds on HTML documents.
Do Not Print Print
Select the optimal paper size, scaling, and orientation.
Invert bitonal monochrome images.
Scale the image to fit the selected paper size.
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width
Set the image orientation.
Portrait Landscape Reverse Portrait Reverse Landscape

Understanding the printer menus 101
Print All Guides Prints all the guides
Color Quality Provides information about solving color quality issues
Print Quality Provides information about solving print quality issues
Printing Guide Provides information about loading paper and other specialty media
Media Guide Provides a list of the paper sizes supported in trays and feeders
Print Defects Guide Provides a template for determining the cause of repeating print quality defects, and lists settings that can be used to adjust print quality
Menu Map Provides a list of the control panel menus and settings
Information Guide Provides help in locating additional information
Connection Guide Provides information about connecting the printer locally (USB) or to a network
Moving Guide Provides instructions for safely moving the printer
Supplies Guide Provides information about ordering supplies
Menu item Description

Saving money and the environment 102
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see “Using Eco‑Mode” on page 102.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 48.
Use Eco‑Mode to quickly select one or more ways to reduce your printer's environmental impact.
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Eco‑Mode > > select the setting you want

Saving money and the environment 103
Off Use the factory default settings for all settings associated with Eco‑Mode. This setting supports the performance specifications for your printer.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy and Paper modes.
2 Press .
Use Quiet mode to reduce the printer noise.
1 From the printer control panel, navigate to:
> Settings > > Settings > General Settings > > Quiet Mode > > select a setting you want
On Reduce printer noise.
Off Use factory default settings.
2 Press .
Use To · Use To

Saving money and the environment 104
1 From the control panel, navigate to:
> Settings > > Settings > > General Settings > > Timeouts > > Sleep Mode >
2 In the Sleep Mode field, select the number of minutes the printer is idle before it enters Sleep mode.
3 Apply the changes.
Hibernate is an ultra‑low‑power saving mode.
1 From the control panel, navigate to:
> Settings > > Settings > > General Settings >
2 Select Press Sleep Button or Press and Hold Sleep Button, and then press .
3 Press Hibernate > .
Hibernate Timeout lets you set the amount of time the printer waits after a print job is processed before it goes into a reduced power state.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Timeouts.
3 From the Hibernate Timeout menu, select the number of hours, days, weeks, or months you want for the printer to wait before it goes into a reduced power state.
4 Click Submit.

Saving money and the environment 105
1 From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Timeouts > > Hibernate Timeout >
2 Select the amount of time the printer waits after a print job is processed before it enters Hibernate mode.
3 Press .
Schedule Power Modes lets you schedule when the printer goes into a reduced power state or into the Ready state.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings > Schedule Power Modes.
3 From the Action menu, select the power mode.
4 From the Time menu, select the time.
5 From the Day(s) menu, select the day or days.
6 Click Add.
To save energy, or to make the display easier to read, adjust its brightness settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the percentage of the brightness you want for the display.
4 Click Submit.

Saving money and the environment 106
From the printer control panel, navigate to:
> Settings > > General Settings > > Screen Brightness >
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
The Lexmark Cartridge Collection Program allows you to return used cartridges for free to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. The boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, do the following:
1 Go to www.lexmark.com/recycle.
2 Select the product that you want to recycle.

Securing the printer 107
Using the security lock feature
The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers in the location shown to secure the printer in place.


Your printer contains various types of memory that can store device and network settings, and user data.
Type of memory Description
Volatile memory Your printer uses standard random access memory (RAM) to temporarily buffer user data during simple print jobs.
Non-volatile memory Your printer may use two forms of non-volatile memory: EEPROM and NAND (flash memory). Both types are used to store operating system, device settings, and network information.
Erase the content of any installed printer memory in the following circumstances:

Securing the printer 108
The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffered data, simply turn off the printer.
Erase individual settings, device and network settings, security settings, and embedded solutions by following these steps:
1 Turn off the printer.
2 Hold down 2 and 6 on the keypad while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display.
3 Press the up or down arrow button until Wipe All Settings appears.
The printer will restart several times during this process.
4 Navigate to:
Back > Exit Config Menu
The printer will perform a power‑on reset, and then return to normal operating mode.
In high-security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer cannot be accessed by unauthorized persons. For more information, visit the Lexmark security Web page.
You can also see the Embedded Web Server — Security: Administrator’s Guide for additional information:
1 Go to www.lexmark.com, and then navigate to Support & Downloads > select your printer.
2 Click the Manuals tab, and then select Embedded Web Server — Security: Administrator’s Guide.

Maintaining the printer 109
1 Turn off the printer, and then unplug the power cord from the electrical outlet.
2 Remove paper from the standard bin and multipurpose feeder.
3 Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.
4 Wipe the outside of the printer with a damp, soft, lint‑free cloth.
5 Connect the power cord, and then turn on the printer.
A message appears on the display when a replacement supply item is needed or when maintenance is required. For more information, see “Supplies menu” on page 60.
From the printer control panel, navigate to:
> Status/Supplies > View Supplies >
1 Open a Web browser, and then type the printer IP address in the address field.

Maintaining the printer 110
2 Click Device Status > More Details.
The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy may vary significantly and is dependent on many factors, such as actual document content, print quality settings, and other printer settings.
The accuracy of the estimated number of remaining pages may decrease when the actual printing consumption is different from the historical printing consumption. Consider the variable level of accuracy before purchasing or replacing supplies based on the estimate. Until an adequate print history is obtained on the printer, initial estimates assume future supplies consumption based on the International Organization for Standardization* test methods and page content.
* Average continuous black or composite CMY declared cartridge yield in accordance with ISO/IEC 19798.
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, go to www.lexmark.com or contact the place where you purchased the printer.
The Lexmark Return Program lets you purchase Lexmark supplies at a discounted price in exchange for your agreement to use the supplies only once and return them only to Lexmark for remanufacturing or recycling.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third-party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. Use of third-party supplies or parts can affect warranty coverage. Damage caused by the use of third-party supplies or parts is not covered by the warranty. All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.

Maintaining the printer 111

For more information on countries located in each region, go to www.lexmark.com/regions

For more information on countries located in each region, go to www.lexmark.com/regions

For more information on countries located in each region, go to www.lexmark.com/regions

Maintaining the printer 112

For more information on countries located in each region, go to www.lexmark.com/regions

For more information on countries located in each region, go to www.lexmark.com/regions

Item All countries and regions
Waste toner bottle C540X75G
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:

Maintaining the printer 113

2 Waste toner bottle
3 Right side cover
1 Unpack the replacement waste toner bottle.
2 Open the front door.
1 Top door · 4 Front door

Maintaining the printer 114

3 Open the top door.

4 Remove the right side cover.


Maintaining the printer 115
5 Remove the waste toner bottle.


6 Pack the used waste toner bottle.
For more information, see “Recycling Lexmark products” on page 106.
7 Insert the replacement waste toner bottle.


Maintaining the printer 116
8 Insert the right side cover.

9 Close the top door.
10 Close the front door.
1 Open the front door.

Maintaining the printer 117
2 Open the top door.
3 Remove the toner cartridges.


4 Remove the right side cover.


Maintaining the printer 118
5 Remove the waste toner bottle.

6 Lift the blue levers on the imaging kit, and then pull the imaging kit until it stops.

7 Press down the blue lever, and then grasp the green handles on the sides to pull out the imaging kit.


Maintaining the printer 119
8 Unpack the replacement black and color imaging kit.


9 Pack the used imaging kit.
For more information, see “Recycling Lexmark products” on page 106.

10 Gently shake the yellow, cyan, magenta, and black developer units side‑to‑side.


Maintaining the printer 120
11 Remove the red packing strip and the attached fabric from the developer units.

12 Insert the yellow, cyan, magenta, and black developer units into the matching color slots.

13 Remove the red packing strip from the imaging kit.



Maintaining the printer 121
14 Align, and then insert the imaging kit.

15 Push the blue levers down until the imaging kit is fully seated into place.

Maintaining the printer 122
16 Insert the waste toner bottle.
17 Insert the right side cover.


Maintaining the printer 123
18 Insert the toner cartridges.

19 Close the top door.
20 Close the front door.
1 Slide the release latch on the right side of the printer, and then open the top door.


Maintaining the printer 124
2 Remove the toner cartridge by lifting the handle, and then gently pulling it away from the imaging kit.


3 Unpack the new toner cartridge, and then remove its packaging.

Maintaining the printer 125
4 Align the new toner cartridge, and then press the cartridge down until it fits into place.

5 Close the top door.
6 Seal the used toner cartridge in the bag that the replacement toner cartridge came in before disposing.
For more information, see “Recycling Lexmark products” on page 106.
Replace the developer unit when a print quality defect occurs or when damage occurs to the printer.
1 Open the front door.

Maintaining the printer 126
2 Open the top door.
3 Remove the toner cartridges.

Maintaining the printer 127
4 Remove the right side cover.
5 Remove the waste toner bottle.
6 Lift the blue levers on the imaging kit, and then pull the imaging kit until it stops.

Maintaining the printer 128
7 Press down the blue lever, and then grasp the green handles on the sides to pull out the imaging kit.
8 Remove the used developer unit.

9 Gently shake the replacement developer unit side‑to‑side before removing it from its packaging.

Maintaining the printer 129
10 Remove the red shipping cover from the developer unit.
11 Insert the developer unit.
12 Align, and then insert the imaging kit.

Maintaining the printer 130
13 Push the blue levers down until the imaging kit is fully seated into place.
14 Insert the waste toner bottle.

Maintaining the printer 131
15 Insert the right side cover.
16 Insert the toner cartridges.
17 Close the top door.
18 Close the front door.
19 Pack the used developer unit in the bag that the replacement developer unit came in before disposing.
For more information, see “Recycling Lexmark products” on page 106.

Maintaining the printer 132
When shipping the printer, use the original packaging.

Managing the printer 133
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
This application enables you to interact with the printer control panel even when you are not physically near the network printer. From your computer, you can view the printer status, release held print jobs, create bookmarks, and do other print-related tasks.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Remote Operator Panel Settings.
3 Select the Enable check box, and then customize the settings.
4 Click Submit.
To use the application, click Remote Operator Panel > Launch VNC Applet.
You can view paper tray settings, the level of toner in the toner cartridges, the percentage of life remaining in the maintenance kit, and capacity measurements of certain printer parts from the Device Status page of the Embedded Web Server.
1 Type the printer IP address in the address field of your Web browser.
2 Click Device Status.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, network, and supplies.
1 Open a Web browser, and then type the printer IP address in the address field.

Managing the printer 134
2 Click Reports, and then click the type of report you want to view.
You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Print Settings > Supply Notifications.
3 From the drop‑down menu for each supply, select one of the following notification options:
Off The normal printer behavior for all supplies occurs.
E‑mail Only The printer generates an e-mail when the supply condition is reached. The status of the supply appears on the menus page and status page.
Continuable Stop1 The printer stops processing jobs when the supply condition is reached. The user needs to press a button to continue printing.
Non Continuable Stop1,2 The printer stops when the supply condition is reached. The supply must be replaced
to continue printing.
1 The printer generates an e-mail about the status of the supply when supply notification is enabled.
2 The printer stops when some supplies become empty to prevent damage.
4 Click Submit.
Notification Description

Managing the printer 135
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Security > Confidential Print Setup.
4 Click Submit to save the modified settings.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click the Copy Printer Settings.
3 To change the language, select a language from the drop-down menu, and then click Click here to submit language.
4 Click Printer Settings.
5 Type the IP addresses of the source and target printers in their appropriate fields.
6 Click Copy Printer Settings.
If you want to keep a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings. For more information, see “Printing a menu settings page” on page 31.
If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 108.

Managing the printer 136
From the printer control panel, navigate to:
> Settings > > Settings > > General Settings > > Factory Defaults > > Restore Now
>

Avoiding jams
Correct loading of paper Incorrect loading of paper

Clearing jams 137




Remove the jammed paper.

1 Open the front door.

2 Remove the jammed paper.





3 Close the front door.
Clearing jams 140

1 Open the front door.
2 Remove the jammed paper.
3 Close the front door.
1 Pull out the tray.

Clearing jams 141

2 Remove the jammed paper.

3 Insert the tray.
1 Remove the tray.

2 Remove the jammed paper.
Clearing jams 142


3 Insert the tray.
1 Remove paper from the multipurpose feeder.
2 Remove the jammed paper.
3 Flex, fan, and align the paper edges before loading.

Clearing jams 143

4 Reload paper.

Clearing jams 144

Understanding the printer messages
Wait for the process to complete.
Try one or more of the following:
press to confirm.
Try one or more of the following:
press to confirm.
Try one or more of the following:
press to confirm.
Make sure the right side cover is installed, and then close the front and top doors to clear the message.
Troubleshooting 145
![Page 146 of the Lexmark CS417dn user manual — [Type] imaging kit very low, [x] estimated pages remain [84.xy]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-146.webp?w=400)
You may need to order a toner cartridge. If necessary, select Continue to clear the message and continue
printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the toner cartridge very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to order an imaging kit. If necessary, select Continue on the printer control panel to clear the
message and continue printing. For non‑touch‑screen printer models, press to confirm.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
You may need to replace the imaging kit very soon. For more information, see the “Replacing supplies” section of the User’s Guide.
If necessary, select Continue on the printer control panel to clear the message and continue printing. For
non‑touch‑screen printer models, press to confirm.
Troubleshooting 146
![Page 147 of the Lexmark CS417dn user manual — Incompatible tray [x] [59]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-147.webp?w=400)
Try one or more of the following:
non‑touch‑screen printer models, press to confirm.
Held jobs are invalidated because of any of the following possible changes in the printer:
From the printer control panel, select Continue to clear the message. For non-touch-screen printer models,
press to confirm.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Cancel the current print job.
Error reading USB drive. Remove USB.
An unsupported USB device is inserted. Remove the USB device, and then insert a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
Remove, and then reinstall the indicated tray to clear the message.
Troubleshooting 147
![Page 148 of the Lexmark CS417dn user manual — Insufficient memory, some held jobs will not be restored [37]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-148.webp?w=400)
Try one or more of the following:
Insert the indicated tray into the printer.
The printer deleted some held jobs in order to process current jobs.
Select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Try one or more of the following:
collating the rest of the print job. For non‑touch‑screen printer models, press to confirm. • Cancel the current print job.
Install additional printer memory or select Continue on the printer control panel to disable Resource Save,
clear the message, and continue printing. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
models, press to confirm. • Delete other held jobs to free up additional printer memory.
Troubleshooting 148
![Page 149 of the Lexmark CS417dn user manual — Load [paper source] with [paper type] [paper size]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-149.webp?w=400)
Try one or more of the following:
panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
control panel. For non‑touch‑screen printer models, press to confirm.
Try one or more of the following:
printer control panel. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 149
![Page 150 of the Lexmark CS417dn user manual — Maintenance kit nearly low [80.xy]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-150.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
You may need to order a maintenance kit. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer
models, press to confirm.
For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
Troubleshooting 150
![Page 151 of the Lexmark CS417dn user manual — Non-Lexmark [supply type], see User's Guide [33.xy]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-151.webp?w=400)
If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer
models, press to confirm.
You may need to replace the maintenance kit very soon. For more information, go to http://support.lexmark.com or contact customer support.
If necessary, press on the printer control panel to clear the message and continue printing.
Try one or more of the following:
models, press to confirm. • Install additional printer memory.
Try one or more of the following:
Try one or more of the following:
The printer has detected a non‑Lexmark supply or part installed in the printer.
Your Lexmark printer is designed to function best with genuine Lexmark supplies and parts. Use of third- party supplies or parts may affect the performance, reliability, or life of the printer and its imaging components. For more information, see “Using genuine Lexmark parts and supplies” on page 110.
Troubleshooting 151
![Page 152 of the Lexmark CS417dn user manual — Reinstall missing or unresponsive [color] cartridge [31.xy]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-152.webp?w=400)
All life indicators are designed to function with Lexmark supplies and parts, and may deliver unpredictable results if third-party supplies or parts are used. Imaging component usage beyond the intended life may damage your Lexmark printer or its associated components.
To accept any and all of these risks, and to proceed with the use of non-genuine supplies or parts in your
printer, press and on the control panel simultaneously for 15 seconds to clear the message and continue printing.
If you do not want to accept these risks, then remove the third-party supply or part from your printer and install a genuine Lexmark supply or part.
Printer had to restart. Last job may be incomplete.
From the printer control panel, press to clear the message and continue printing.
For more information, go to http://support.lexmark.com or contact customer support.
Try one or more of the following:
Reinstall missing or unresponsive black and color imaging kit and all cartridges [31.xy]
Try one or more of the following:
For information on installing the imaging kit, see the “Replacing supplies” section. • If the imaging kit is installed, then remove and reinstall the unresponsive imaging kit.
Troubleshooting 152
![Page 153 of the Lexmark CS417dn user manual — Replace missing [color] cartridge [31.xy]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-153.webp?w=400)
Try any of the following:
side of the sheet. For non‑touch‑screen printer models, press to confirm. • Cancel the print job.
1 Remove any remaining packing material from the indicated location.
2 From the printer control panel, touch Continue to clear the message. For non‑touch‑screen printer
models, press to confirm.
Remove the paper stack from the standard bin.
Replace the indicated imaging kit to clear the message and continue printing. For more information, see the instruction sheet that came with the supply.
Replace the defective toner cartridge to clear the message. For more information, see the instruction sheet that came with the supply.
The printer is scheduled for maintenance. For more information, go to http://support.lexmark.com or contact your service representative, and then report the message.
Install the indicated toner cartridge to clear the message. For more information, see the “Replacing supplies” section of the User’s Guide.
Troubleshooting 153

Install the indicated imaging kit to clear the message. For more information, see the “Replacing supplies” section of the User’s Guide.
Install the missing waste toner bottle to clear the message. For more information, see the instruction sheet that came with the supply.
Remove the toner cartridge, and then install a supported one to clear the message.
Remove the indicated imaging kit, and then install a supported one to clear the message.
Replace the waste toner bottle to clear the message.
Try one or more of the following:
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models,
press to confirm.
Troubleshooting 154
![Page 155 of the Lexmark CS417dn user manual — Too many trays attached [58]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-155.webp?w=400)
Try one or more of the following:
From the printer control panel, select Continue to clear the message. For non‑touch‑screen printer models,
press to confirm.
Try one or more of the following:
to clear the message and continue printing. 1 Order the missing supply immediately. 2 Install the supply. For more information, see the instruction sheet that came with the supply. • Cancel the print job, then install the missing supply, and then resend the print job.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra flash memory.
4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
1 Turn off the printer.
2 Unplug the power cord from the electrical outlet.
3 Remove the extra trays.
Troubleshooting 155

4 Connect the power cord to a properly grounded electrical outlet.
5 Turn the printer back on.
Try one or more of the following:
non‑touch‑screen printer models, press to confirm. • Format the flash memory.
You may need to order a waste toner bottle. If necessary, select Continue on the printer control panel to
clear the message and continue printing. For non‑touch‑screen printer models, press to confirm.
Go to step 2. Turn on the printer.
Make sure the printer is turned on.
Is the printer turned on?
Press the Sleep button to wake the printer from Sleep mode or Hibernate mode.
Go to step 3.
Check if the printer is in Sleep mode or Hibernate mode.
Is the printer in Sleep mode or Hibernate mode?
Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet.
Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Is the power cord plugged into the printer and a properly grounded electrical outlet?
![Page 157 of the Lexmark CS417dn user manual — Unformatted flash detected [53]](/cdn/reader/00/00fe95375d4ead21eeb31c89f3ef395fd4b02a68bfaa2fb7cdbca9009104b776/images/page-157.webp?w=400)
Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment.
Go to step 5.
Check other electrical equipment plugged into the electrical outlet.
Does other electrical equipment work?
Go to step 6. Make sure to match the following:
Check if the cables connecting the printer and the computer are inserted in the correct ports.
Are the cables inserted in the correct ports?
Turn on the switch or reset the breaker.
Go to step 7.
Make sure the electrical outlet is not turned off by a switch or breaker.
Is the electrical outlet turned off by a switch or breaker?
Connect the printer power cord directly to a properly grounded electrical outlet.
Go to step 8.
Check if the printer is plugged into any surge protectors, uninterruptible power supplies, or extension cords.
Is the printer plugged into any surge protectors, uninterruptible power supplies, or extension cords?
Go to step 9. Connect the printer cable securely to the printer and the computer, print server, option, or other network device.
Check if one end of the printer cable is plugged into a port on the printer and the other to the computer, print server, option, or other network device.
Is the printer cable securely attached to the printer and the computer, print server, option, or other network device?
Step 9 Make sure to install all hardware options properly and remove any packing material.
Go to step 10. Turn off the printer, remove all packing materials, then reinstall the hardware options, and then turn on the printer.
Are all hardware options properly installed and all packing material removed?
Go to step 11. Use correct printer driver settings.
Check if you have selected the correct port settings in the printer driver.
Are the port settings correct?

Go to step 12. Install the correct printer driver.
Check the installed printer driver.
Is the correct printer driver installed?
Step 12 Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
The problem is solved.
Contact customer support.
Is the printer working?
The problem is solved.
Go to step 2.
Press the Sleep button on the printer control panel.
Does Ready appear on the printer display?
The problem is solved.
Turn off the printer, and then contact customer support.
Turn off the printer, then wait for about 10 seconds, and then turn the printer back on.
Do Please wait and Ready appear on the printer display?
Make sure the memory card is installed.
The problem is solved.
Contact customer support.
a Install the memory card. For more information, see “Installing a
memory card” on page 20.
in the Installed Options list.
Is the card listed in the Installed Options list?

The problem is solved.
Go to step 2.
Turn off the printer, then wait for about 10 seconds, and then turn on the printer.
Does the internal option operate correctly?
Go to step 3. Connect the internal option to the controller board.
Check if the internal option is properly installed in the controller board.
a Turn off the printer using the power switch, and then unplug the
power cord from the electrical outlet. b Make sure the internal option is installed in the appropriate
connector in the controller board. c Connect the power cord to the printer, then to a properly
grounded electrical outlet, and then turn on the printer.
Is the internal option properly installed in the controller board?
Go to step 4. Reinstall the internal option.
Print a menu settings page, and then check to see if the internal option is listed in the Installed Features list.
Is the internal option listed in the menu settings page?
The problem is solved.
Contact customer support.
a Check if the internal option is selected.
It may be necessary to manually add the internal option in the printer driver to make it available for print jobs. For more information, see “Adding available options in the print driver” on page 27. b Resend the print job.
Does the internal option operate correctly?

The problem is solved.
Go to step 2.
a Pull out the tray, and then do one or more of the following:
Is the tray working?
The problem is solved.
Go to step 3.
a Turn off the printer, then wait about 10 seconds, and then turn
the printer back on. b Resend the print job.
Is the tray working?
Go to step 4. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Check if the tray is installed and recognized by the printer.
Print a menu settings page, and then check if the tray is listed in the Installed Features list.
Is the tray listed in the menu settings page?
The problem is solved.
Contact customer support.
Check if the tray is available in the printer driver.
Is the tray available in the printer driver?

a Turn on jam recovery.
The problem is solved.
Contact customer support.
1 From the printer control panel, navigate to: Settings > General Settings > Print Recovery > Jam Recovery 2 Select On or Auto.
3 Depending on your printer model, press or touch Submit. b Resend the pages that did not print.
Were the jammed pages reprinted?
Go to step 2. The problem is solved.
a Pull out the tray, and then do one or more of the following:
If jam recovery is enabled, then the print jobs will reprint automatically.
Do paper jams still occur frequently?
Go to step 3. The problem is solved.
a Load paper from a fresh package.
Do paper jams still occur frequently?

Contact customer support.
The problem is solved.
a Review the tips on avoiding jams. For more information, see
“Avoiding jams” on page 137. b Follow the recommendations, and then resend the print job.
Do paper jams still occur frequently?
a Do either of the following:
Contact customer support.
The problem is solved.
or Done.
Clear the jam, press OK > . b Follow the instructions on the printer display.
Does the paper jam message remain?
Go to step 2. Contact customer support.
Check the system log for relevant details.
a Open a Web browser, and then type the printer IP address in
the address field.
If you do not know the IP address of the printer, then you can:
Log. c From the Filter menu, select an application status. d From the Application menu, select an application, and then
click Submit.
Does an error message appear in the log?

The problem is solved.
Contact customer support.
Resolve the error. Is the application working now?
Step 1 Make sure the printer is not in Hex Trace mode.
Deactivate Hex Trace mode.
Go to step 2.
Is the printer in Hex Trace mode?
Contact customer support.
The problem is solved.
a From the printer control panel, select Standard Network or
Network [x], and then set SmartSwitch to On. b Resend the print job.
Do incorrect characters print?
The problem is solved.
Go to step 2.
a Check if you are printing on paper that is supported by the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved.
Go to step 3.
a From the Paper menu on the printer control panel, set the paper
size and type to match the paper loaded in the tray. b Resend the print job.
Did the job print from the correct tray or on the correct paper?

The problem is solved.
Go to step 4.
a Depending on your operating system, open Printing
Preferences or the Print dialog, and then specify the paper type. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved.
Contact customer support.
a Check if the trays are not linked. b Resend the print job.
Did the job print from the correct tray or on the correct paper?
The problem is solved.
Go to step 2.
a From the Finishing menu on the printer control panel, set
Collate to (1,2,3) (1,2,3). b Resend the print job.
Did the job print and collate correctly?
The problem is solved.
Go to step 3.
a From the printer software, set Collate to (1,2,3) (1,2,3).
Did the job print and collate correctly?
Step 3 Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
The problem is solved.
Contact customer support.
Did the job print and collate correctly?

Place letter‑ or A4‑size paper in the tray, and then resend the print job.
The problem is solved.
Contact customer support.
Does the print speed increase?
The problem is solved.
Go to step 2.
a From the document you are trying to print, open the Print dialog
and check if you have selected the correct printer.
Do the jobs print?
The problem is solved.
Go to step 3.
a Check if the printer is plugged in and turned on, and if Ready
appears on the printer display. b Resend the print job.
Do the jobs print?
The problem is solved.
Go to step 4.
If an error message appears on the printer display, then clear the message.
Do the jobs print?
The problem is solved.
Go to step 5.
a Check if the ports (USB, serial, or Ethernet) are working and if
the cables are securely connected to the computer and the printer.
Do the jobs print?

The problem is solved.
Go to step 6.
a Turn off the printer, then wait for about 10 seconds, and then
turn the printer back on. b Resend the print job.
Do the jobs print?
The problem is solved.
Contact customer support.
a Remove, and then reinstall the printer software. For more
information, see “Installing the printer software” on page 26.
Do the jobs print?
Step 1 Change the environmental settings of the printer.
The problem is solved.
Go to step 2.
a From the printer control panel, navigate to:
Settings > General Settings b Select Eco‑Mode or Quiet Mode, and then select Off.
Did the job print?
The problem is solved.
Go to step 3.
Reduce the number and size of fonts, the number and complexity of images, and the number of pages in the print job, and then resend the job
Did the job print?
The problem is solved.
Go to step 4.
a Remove held jobs stored in the printer memory. b Resend the print job.
Did the job print?

The problem is solved.
Go to step 5.
a Disable the Page Protect feature.
From the printer control panel, navigate to: Settings > General Settings > Print Recovery > Page Protect > Off b Resend the print job.
Did the job print?
The problem is solved.
Go to step 6.
a Check if the cable connections to the printer and print server
are secure. For more information, see the setup documentation that came with the printer. b Resend the print job.
Did the job print?
The problem is solved.
Contact customer support.
Install additional printer memory, and then resend the print job.
Did the job print?

a Check if the distance between the defects is equal to one of
1 Check if the distance between the defects is equal to one of the following:
The problem is solved.
the following:
29.8 mm (1.17 in.), or 94.2 mm (3.70 in.), then replace the photoconductor unit. c If the distance between the defects equals 43.9 mm (1.72 in.) or
45.5 mm (1.79 in.), then replace the developer unit.
Do the repeating defects still appear?
The problem is solved.
Go to step 2.
a Open the trays, and then check if they contain paper of the
same size and type.
Do the trays link correctly?

The problem is solved.
Contact customer support.
a From the printer control panel, set the paper size and type in
the Paper menu to match the paper loaded in the trays to be linked.
Do the trays link correctly?
Step 1 Adjust the print timeout settings.
The problem is solved.
Go to step 2.
a From the printer control panel, navigate to:
Settings > General Settings > Timeouts > Print Timeout b Select a higher setting and then, depending on your printer
model, select or Submit. c Resend the print job.
Did the file print correctly?
The problem is solved.
Contact customer support.
a Check the original file for manual page breaks. b Resend the print job.
Did the file print correctly?


Go to step 2. Select a font that is supported by the printer.
a Print a font sample list to check if the fonts you are using are
1 From the printer control panel, navigate to any of the following:
> Reports > Print Fonts • Settings > Reports > Print Fonts 2 Select PCL Fonts or PostScript Fonts. b Resend the print job.
Are you using fonts that are supported by the printer?
Check if the fonts installed on the computer are supported by the printer.
Are the fonts installed on the computer supported by the printer?

a Move the width and length guides in the tray to the correct
positions for the paper loaded. b Resend the print job.
Troubleshooting 170

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper size
from Printing Preferences or from the Print dialog. b Resend the print job.
Is the page or image clipped?
Contact customer support.
The problem is solved.
a Remove, and then reinstall the imaging kit.
Is the page or image clipped?
ABCDE
ABCDE ABCDE


a From the Quality menu on the printer control panel, reduce the

a Make sure your software program is using a correct fill pattern. b Resend the print job.
a Load the specified tray or feeder with a recommended type of
Troubleshooting 172

Go to step 4. The problem is solved.
a Remove, and then reinstall the imaging kit.
Do horizontal voids appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do horizontal voids appear on prints?
ABCD ABCD ABCD
The problem is solved.
Go to step 2.
a Move the width and length guides in the tray to the correct
positions for the paper size loaded. b Resend the print job.
Are the margins correct?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size in the Paper menu to match the paper loaded in the tray.
Does the paper size match the paper loaded in the tray?

The problem is solved.
Contact customer support.
a Depending on your operating system, specify the paper size
from Printing Preferences or from the Print dialog. b Resend the print job.
Are the margins correct?
Go to step 2. Adjust the width and length guides.
Move the width and length guides in the tray to the correct positions for the size of the paper loaded.
Are the width and length guides positioned correctly?
Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the type and weight of the paper in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the paper still curled?
Go to step 5. The problem is solved.
a Remove the paper from the tray, and then turn it over. b Resend the print job.
Is the paper still curled?
Contact customer support.
The problem is solved.
a Load paper from a fresh package.
Is the paper still curled?

Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, select
Color Adjust. b Resend the print job.
Is the print still too dark?
Go to step 3. The problem is solved.
a From the Quality menu on the printer control panel, reduce the
toner darkness.
Is the print still too dark?
Go to step 4. Change the paper loaded in the tray to match the paper type, texture, and weight specified in the tray settings.
a From the printer control panel, set the paper type, texture, and
weight in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Is the tray set to the type, texture, and weight of the paper loaded?
Go to step 5. The problem is solved.
a Depending on your operating system, specify the paper type,
texture and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Is the print still too dark?
Step 5 Check if the paper loaded in the tray has texture or rough finishes.
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded on the tray.
Go to step 6.
Are you printing on textured or rough paper?

Go to step 7. The problem is solved.
a Load paper from a fresh package.
Is the print still too dark?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the print still too dark?
Go to step 2. The problem is solved.
a From the Quality menu on the printer control panel, select
Color Adjust. b Resend the print job.
Is the print still too light?
Go to step 3. The problem is solved.
a From the Quality menu on the printer control panel, increase
the toner darkness.
Is the print still too light?
Go to step 4. Specify the paper type, texture, and weight from the tray settings to match the paper loaded in the tray.
From the printer control panel, set the paper type, texture, and weight in the Paper menu to match the paper loaded in the tray.
Is the tray set to the type, texture, and weight of the paper loaded?


a Depending on your operating system, specify the paper type,
texture, and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Step 5 Make sure that the paper has no texture or rough finishes.
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray
Replace the imaging kit, and then resend the print job.

a Move the width and length guides in the tray to the correct
positions for the size of the paper loaded in the tray. b Resend the print job.
Troubleshooting 177

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Is the tray set to the size and type of the paper loaded in the tray?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do print irregularities still appear?
Step 4 Check if the paper loaded in the tray has texture or rough finishes.
From the printer control panel, set the paper texture in the Paper menu to match the paper loaded in the tray.
Go to step 5.
Are you printing on textured or rough paper?
Go to step 6. The problem is solved.
a Load paper from a fresh package.
Do print irregularities still appear?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do print irregularities still appear?


Go to step 2. The problem is solved.
a Check if there is packing material left on the imaging kit.
1 Remove the imaging kit. 2 Check if the packing material is properly removed from the imaging kit.
Is the printer still printing blank pages?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the printer still printing blank pages?

Go to step 2. The problem is solved.
a Remove, and then reinstall the imaging kit.
Is the printer printing solid black pages?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Is the printer printing solid black pages?

ABCD ABCD ABCD ABCD

Go to step 2. Load paper with the correct paper type and weight in the tray.
Check if the paper loaded in the tray has the correct paper type and weight.
Is paper with the correct paper type and weight loaded in the tray?
Step 2 From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Go to step 3. Change the paper type and weight to match the paper loaded in the tray.
Do the printer settings match the type and weight of the paper loaded?
Go to step 4. The problem is solved.
a Depending on your operating system, specify the paper type
and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Do shadow images still appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do shadow images still appear on prints?
) ) ABCDE
ABCDE ABCDE

Go to step 2. The problem is solved.
a Move the width and length guides in the tray to the correct
positions for the size of the paper loaded. b Resend the print job.
Is the print still skewed?
Contact customer support.
The problem is solved.
a Check if you are printing on a paper that is supported by the
tray. b Resend the print job.
Is the print still skewed?
ABCDE ABCDE ABCDE
Go to step 2. The problem is solved.
a Depending on your operating system, specify the tray or feeder
from Printing Preferences or the Print dialog. b Resend the print job.
Do streaked horizontal lines appear on prints?
Go to step 3. Do one or more of the following:
From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray.
Do the paper type and weight match the paper in the tray?


Replace the imaging kit, and then resend the print job.

a Depending on your operating system, specify the paper type,
texture, and weight from Printing Preferences or from the Print dialog. b Resend the print job.
Troubleshooting 182

Go to step 3. Do one or more of the following:
From the printer control panel, set the paper texture, type, and weight in the Paper menu to match the paper loaded in the tray.
Do the paper texture, type, and weight match the paper in the tray?
Go to step 4. The problem is solved.
a Load paper from a fresh package.
Do streaked vertical lines appear on prints?
Go to step 5. The problem is solved.
a Remove, and then reinstall the imaging kit.
Do streaked vertical lines appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do streaked vertical lines appear on prints?

Go to step 2. Set the paper type to Transparency.
From the printer control panel, set the paper type in the Paper menu to match the paper loaded in the tray.
Is the paper type for the tray set to Transparency?
Contact customer support.
The problem is solved.
a Check if you are using a recommended type of transparency. b Resend the print job.
Is the print quality still poor?
ABCDE
ABCDE ABCDE
The problem is solved.
Go to step 2.
a Remove, and then reinstall the imaging kit.
Does fog or shading disappear from the prints?
The problem is solved.
Contact customer support.
Replace the imaging kit, and then resend the print job.
Does fog or shading disappear from the prints?


Go to step 2. Specify the paper type, texture, and weight from the tray settings to match the paper loaded in the tray.
From the Paper menu on the printer control panel, check the paper type, texture, and weight.
Do the paper type, texture, and weight match the paper loaded in the tray?

a Check if your software program is using a correct fill pattern. b Resend the print job.
a From the Paper Menu on the printer control panel, check the
paper type and paper weight. b Resend the print job.
Troubleshooting 185

Go to step 4. The problem is solved.
Check if you are using a recommended type of paper.
a Load paper source with a recommended type of paper. b Resend the print job.
Do vertical voids appear on prints?
Go to step 5. The problem is solved.
a Remove, and then reinstall the imaging kit.
Do vertical voids appear on prints?
Contact customer support.
The problem is solved.
Replace the imaging kit, and then resend the print job.
Do vertical voids appear on prints?
Replace the imaging kit, and then resend the print job.
Contact customer support.
The problem is solved.
Is the print density uneven?

What is RGB color?
Red, green, and blue light can be added together in various amounts to produce a large range of colors observed in nature. For example, red and green can be combined to create yellow. Televisions and computer monitors create colors in this manner. RGB color is a method of describing colors by indicating the amount of red, green, or blue needed to produce a certain color.
What is CMYK color?
Cyan, magenta, yellow, and black inks or toners can be printed in various amounts to produce a large range of colors observed in nature. For example, cyan and yellow can be combined to create green. Printing presses, inkjet printers, and color laser printers create colors in this manner. CMYK color is a method of describing colors by indicating the amount of cyan, magenta, yellow, and black needed to reproduce a particular color.
How is color specified in a document to be printed?
Software programs typically specify the document color using RGB or CMYK color combinations. Additionally, they let users modify the color of each object in a document. For more information, see the help information of your operating system.
How does the printer know what color to print?
When a user prints a document, information describing the type and color of each object is sent to the printer. The color information is passed through color conversion tables that translate the color into the appropriate amounts of cyan, magenta, yellow, and black toner needed to produce the color you want. The object information determines the application of color conversion tables. For example, it is possible to apply one type of color conversion table to text while applying a different color conversion table to photographic images.
What is manual color correction?
When manual color correction is enabled, the printer employs user‑selected color conversion tables to process objects. However, Color Correction must be set to Manual, or no user‑defined color conversion will be implemented. Manual color correction settings are specific to the type of object being printed (text, graphics, or images), and how the color of the object is specified in the software program (RGB or CMYK combinations).
To manually apply a different color conversion table, do the following:
1 From the Quality menu on the printer control panel, select Color Correction, and then select Manual.
2 From the Quality menu on the printer control panel, select Manual Color, and then select the appropriate color conversion table for the affected object type.
Troubleshooting 187

Object type Color conversion tables
RGB Image RGB Text
CMYK Image CMYK Text
How can I match a particular color (such as a corporate logo)?
Nine types of Color Samples sets are available from the Quality menu on the printer control panel. These are also available from the Color Samples page of the Embedded Web Server. Selecting any sample set generates a multiple‑page printout consisting of hundreds of colored boxes. Either a CMYK or RGB combination is located on each box, depending on the table selected. The observed color of each box is obtained by passing the CMYK or RGB combination labeled on the box through the selected color conversion table.
By examining Color Samples sets, you can identify the box whose color is the closest to the color you want. The color combination labeled on the box can then be used for modifying the color of the object in a software program. For more information, see the help information of your operating system.
Selecting which Color Samples set to use for a particular color‑matching problem depends on the Color Correction setting being used , the type of object being printed, and how the color of the object is specified in the software program. When Color Correction is set to Off, the color is based on the print job information, and no color conversion is implemented.
Note: The Color Samples pages are not useful if the software program does not specify colors with RGB or CMYK combinations. Additionally, certain situations exist in which the software program or the computer operating system adjusts the RGB or CMYK combinations specified in the program through color management. The resulting printed color may not be an exact match of the Color Samples pages.
Troubleshooting 188 · RGB Graphics · CMYK Graphics

What are detailed color samples and how do I access them?
Detailed color samples sets are available only through the Embedded Web Server of a network printer. A detailed Color Samples set contains a range of shades that are similar to a user‑defined RGB or CMYK value. The likeness of the colors in the set is dependent on the value entered in the RGB or CMYK Increment box.
To access a detailed Color Samples set from the Embedded Web Server, do the following:
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Configuration > Color Samples > Detailed Options.
3 Select a color conversion table.
4 Enter the RGB or CMYK color number.
5 Enter an increment value from 1 to 255.
6 Click Print.
Step 1 From the printer control panel, make sure the paper type setting is set to Transparency.
Go to step 2. Set the paper type to Transparency.
Is the paper type setting correct?
Step 2 Reduce the toner darkness, and then resend the print job.
The problem is solved.
Go to step 3.
Does the print on the color transparency look lighter?
The problem is solved.
Contact customer support.
Make sure you are using a recommended type of color transparency, and then resend the print job.
Does the print on the color transparency look lighter?
Troubleshooting 189 · Action Yes No · Step 3

The color of the print does not match the color of the original file
The problem is solved.
Go to step 2.
a Set Color Correction to Off.
Does the color of the print match the color of the file on the computer screen?
The problem is solved.
Contact customer support.
From the Quality menu on the printer control panel, do the following:
a Select Color Correction, and then select Manual. b Select Manual Color, and then select the appropriate color
conversion table for the affected object type. c Resend the print job.
Does the color of the print match the color of the file on the computer screen?
Adjust the color balance.
The problem is solved.
Contact customer support.
a From the Color Balance menu on the printer control panel,
increase or decrease the values for cyan, magenta, yellow, and black. b Resend the print job.
Does the print still appear tinted?

The problem is solved.
Go to step 2.
a Turn on the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?
The problem is solved.
Go to step 3.
Make sure the printer IP address is correct.
a View the printer IP address:
Does the Embedded Web Server open?
The problem is solved.
Go to step 4.
Check if the network is working.
a Print a network setup page. b Check the first section of the network setup page and confirm
that the status is Connected.
Does the Embedded Web Server open?

The problem is solved.
Go to step 5.
Check if the cable connections to the printer and print server are secure.
a Connect the cables properly. For more information, see the
setup documentation that came with the printer. b Open a Web browser, and then type the printer IP address.
c Press Enter.
Does the Embedded Web Server open?
The problem is solved.
Contact your system support person.
Temporarily disable the Web proxy servers.
Proxy servers may block or restrict you from accessing certain Web sites including the Embedded Web Server.
Does the Embedded Web Server open?
Before contacting customer support, make sure to have the following information:
Go to http://support.lexmark.com to receive e‑mail or chat support, or browse through the library of manuals, support documentation, drivers, and other downloads.
Technical support via telephone is also available. In the U.S. or Canada, call 1-800-539-6275. For other countries or regions, go to http://support.lexmark.com.

Product name:
Lexmark CS410n, CS410dn. CS417dn
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2012 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
410, 430 · November 2017

All licensing notices associated with this product can be viewed from the root directory of the installation software CD.
Lexmark, the Lexmark logo, MarkNet, and MarkVision are trademarks or registered trademarks of Lexmark International, Inc. in the United States and/or other countries.
Google Cloud Print is a trademark of Google Inc.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
Microsoft and Windows are either registered trademarks or trademarks of the Microsoft group of companies in the United States and other countries.
Mopria®, the Mopria® logo, and the Mopria® Alliance logo are registered trademarks and service marks of Mopria Alliance, Inc. in the United States and other countries. Unauthorized use is strictly prohibited.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
PostScript is a registered trademark of Adobe Systems Incorporated in the United States and/or other countries.
The following terms are trademarks or registered trademarks of these companies:
Albertus The Monotype Corporation plc
Antique Olive Monsieur Marcel OLIVE
Apple-Chancery Apple Computer, Inc.
Arial The Monotype Corporation plc
CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation
Chicago Apple Computer, Inc.
Clarendon Linotype-Hell AG and/or its subsidiaries
Geneva Apple Computer, Inc.
GillSans The Monotype Corporation plc
Helvetica Linotype-Hell AG and/or its subsidiaries
Hoefler Jonathan Hoefler Type Foundry
ITC Avant Garde Gothic International Typeface Corporation
ITC Bookman International Typeface Corporation
ITC Mona Lisa International Typeface Corporation
ITC Zapf Chancery International Typeface Corporation
Joanna The Monotype Corporation plc
Eurostile Nebiolo

Monaco Apple Computer, Inc.
New York Apple Computer, Inc.
Palatino Linotype-Hell AG and/or its subsidiaries
Stempel Garamond Linotype-Hell AG and/or its subsidiaries
Times New Roman The Monotype Corporation plc
Univers Linotype-Hell AG and/or its subsidiaries
All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
statement
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Marigold Arthur Baker · Oxford Arthur Baker · Taffy Agfa Corporation

Any questions regarding this compliance information statement should be directed to:
Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 232–3000
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
This product complies with the India E-Waste (Management and Handling) Rules, 2011, which prohibit use of lead, mercury, hexavalent chromium, polybrominated biphenyls, or polybrominated diphenyl ethers in concentrations exceeding 0.1% by weight and 0.01% by weight for cadmium, except for the exemption set in Schedule II of the Rules.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
Printing 50 · Ready 16

This symbol identifies static-sensitive parts. Do not touch the areas near these symbols without first touching a metal surface in an area away from the symbol.
Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient operating temperature 15.6 to 32.2°C (60 to 90°F)
Shipping temperature -40 to 43.3°C (-40 to 110°F)
Storage temperature and relative humidity 1 to 35°C (34 to 95°F)
8 to 80% RH
Consumo de energía en operación:
Consumo de energía en modo de espera:
0.2 Wh
Cantidad de producto por unidad de energía consumida:
2.78 páginas / Wh
540 Wh

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1: 2014.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 12‑milliwatt gallium arsenide laser operating in the wavelength of 655–675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:
Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku. FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista. GEFAHR - Unsichtbare Laserstrahlung beim Herausnehmen von Druckkassetten und offener Sicherheitssperre. Laserstrahl meiden.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser. VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget.
FARE – Usynlig laserstråling når kassettene tas ut og sperren er satt ut av spill. Unngå eksponering for laserstrålen. NIEBEZPIECZEŃSTWO - niewidzialne promieniowanie laserowe podczas usuwania kaset i blokady. Należy unikać naświetlenia promieniem lasera.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей. Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危險 - 移除碳粉匣與安全連續開關失效時會產生看不見的雷射輻射。請避免曝露在雷射光束下。 危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 580 (one-sided); 360 (two- sided)
Copy The product is generating hard‑copy output from hard‑copy original documents.

Mode Description Power consumption (Watts)
Scan The product is scanning hard‑copy documents. N/A
Ready The product is waiting for a print job. 30
Sleep Mode The product is in a high‑level energy‑saving mode. 3
Hibernate The product is in a low‑level energy‑saving mode. 0.5
Off The product is plugged into an electrical outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 20
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 120 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
This product is designed with an ultra‑low power operating mode called Hibernate mode. When operating in Hibernate Mode, all other systems and devices are powered down safely.
The Hibernate mode can be entered in any of the following methods:
Factory default Hibernate Timeout for this product in all countries or regions 3 days
The amount of time the printer waits after a job is printed before it enters Hibernate mode can be modified between one hour and one month.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.

It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをしてください。
VCCI-B
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 2014/30/EU, 2014/35/EU, 2009/125/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, the ecodesign of energy-related products, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative or may be obtained at www.lexmark.com/en_us/about/regulatory-compliance/european-union-declaration-of-conformity.html.
This product satisfies the Class B limits of EN 55022 and EN55032 and safety requirements of EN 60950‑1 or EN 62368-1.

STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country-specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.

As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.

This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.




Load [paper source] with [paper
[Color] cartridge low [88.xy] 146 [Color] cartridge nearly low
size] 149 Load [paper source] with [paper
cartridge [32.xy] 154 Replace unsupported [type]
[88.xy] 146 [Color] cartridge very low, [x]
type] [paper size] 149 Load Manual Feeder with
imaging kit [32.xy] 154 Replace waste toner bottle
estimated pages remain [88.xy] 146 [Type] imaging kit low
[custom string] 150 Load Manual Feeder with
[82.xy] 154 Restore held jobs? 154 Some held jobs were not
[custom type name] 150 Load Manual Feeder with [paper
[84.xy] 146 [Type] imaging kit nearly low
restored 154 Standard network software
size] 150 Load Manual Feeder with [paper
[84.xy] 146 [Type] imaging kit very low, [x]
error [54] 155 Standard USB port disabled
type] [paper size] 150 Maintenance kit low [80.xy] 150 Maintenance kit nearly low
estimated pages remain [84.xy] 146 Adjusting color 145 Change [paper source] to
[56] 155 Supply needed to complete
[80.xy] 150 Maintenance kit very low
job 155 Too many flash options installed
[custom string] 145 Change [paper source] to
[80.xy] 151 Memory full [38] 151 Network [x] software error
[58] 155 Too many trays attached
[custom type name] 145 Change [paper source] to
[58] 155 Unformatted flash detected
[54] 151 Non-Lexmark [supply type], see
[paper type] [paper size] 145 Close door 145 Complex page, some data may
[53] 156 Unsupported USB hub, please
User's Guide [33.xy] 151 Not enough free space in flash
remove 147 Waste toner bottle nearly full
not have printed [39] 147 Configuration change, some
memory for resources [52] 151 Printer had to restart. Last job
[82.xy] 156 printer options troubleshooting
held jobs were not restored [57] 147 Defective flash detected
may be incomplete. 152 Reinstall missing or
internal option is not
unresponsive [color] cartridge [31.xy] 152 Reload printed pages in Tray
detected 159 memory card 158 tray problems 160 printer problems, solving basic 156 printer security
[51] 147 Error reading USB drive.
Remove USB. 147 Error reading USB hub. Remove
[x] 153 Remove packaging material,
hub. 147 Incompatible tray [x] [59] 147 Incorrect paper size, open
[area name] 153 Remove paper from standard
information on 108 printer software, installing 26 printer status
output bin 153 Replace [type] imaging kit, 0
[paper source] [34] 148 Insert Tray [x] 148 Insufficient memory to collate
estimated pages remain [84.xy] 153 Replace defective [color]
checking, using the Embedded
Web Server 133 printing
job [37] 148 Insufficient memory to support
cartridge [31.xy] 153 Replace maintenance kit
black‑and‑white 53 directory list 59 faster speed vs. higher yield 54 font sample list 59 from a computer 53 from a mobile device 56, 57 from flash drive 55 Max Speed and Max Yield 54 menu settings page 31 network setup page 31 printing a network setup page 31 printing from a flash drive 55
Resource Save feature [35] 148 Insufficient memory, some Held
[80.xy] 153 Replace missing [color]
Jobs were deleted [37] 148 Insufficient memory, some held
cartridge [31.xy] 153 Replace missing [type] imaging
jobs will not be restored [37] 148 Load [paper source] with
kit [31.xy] 154 Replace missing or
unresponsive black and color imaging kit and all cartridges [31.xy] 152 Replace missing waste toner
[custom string] 149 Load [paper source] with
[custom type name] 149
bottle [31.xyz] 154
Index 208 · printer messages · Replace unsupported [color]


Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.