


Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.
In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly. Along with a wide range of accessories designed and built to the high quality standards you would expect, from specialist cookware to cutlery baskets, from bottle holders to delicate laundry bags…
We recommend the use of original spare parts.
When contacting Service, ensure that you have the following data available. The information can be found on the rating plate.
Model · Serial Number

Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not re- sponsible if an incorrect installation and use causes injuries and damages. Al- ways keep the instructions with the ap- pliance for future reference.
The water inlet hose has a safety valve and a sheath with an inner mains cable. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact Service to replace the water inlet hose.
Water connection · Electrical connection

The LED is CLASS 2 and agrees with IEC 60825-1: 1993 + A1:1997 + A2:2001. Emission wave length: 450 nm Maximum emitted power: 548 μW To replace the internal light, contact Service.



4 Filters


1 2 3 4 5 6 7 8 9
Salt indicator. This indicator is off while the programme operates.
Rinse aid indicator. This indicator is off while the programme op- erates.


Prewash Wash 45 °C or 70 °C Rinses Dry
7 Normal or light soil Delicate crockery and glassware
1) The appliance senses the type of soil and the quantity of items in the baskets. It automatically adjusts the temperature and quantity of the water, the energy consumption and the programme duration. 2) This programme includes the ExtraHygiene option. 3) This is the most silent washing programme. The pump works at a very low speed to decrease the level of noise. Because of the low speed, the programme duration is long. 4) With this programme you can wash a load with fresh soil. It gives good washing results in a short time. 5) This is the standard programme for test institutes. With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. Refer to the supplied leaflet for test information. 6) Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance. Do not use detergent with this programme.


1 90 - 160 0.9 - 1.7 8 - 15
2 140 - 160 1.4 - 1.6 13 - 14
3 200 - 220 1.1 - 1.2 9 - 11
5 160 - 170 0.9 - 1.0 9 - 11
6 50 - 60 1.0 - 1.1 10 - 11
7 70 - 80 0.8 - 0.9 11 - 12
Consumption values

temperature stays at 70 °C for 10 to 14 minutes.
Activate this function only when you use the combi detergent tablets. This function deactivates the flow of rinse aid and salt. The related indicators are off. The programme duration can increase.
This function decreases the tempera- ture in the drying phase. The energy consumption decreases by 25%. The dishes can be wet at the end of the programme. We recommend that you keep the door ajar and let the dishes dry.
Activating the multitab function
Activate or deactivate the multi- tab function before the start of a programme. You cannot acti- vate or deactivate this function when a programme operates.
Factory setting: on. You can de- activate the acoustic signals.
The function stays on until you deactivate it. Press the multitab touchpad, the multitab indicator goes off.
If you stop to use the combi detergent tablets, before you start to use separately detergent, rinse aid and dishwasher salt, do these steps: 1. Deactivate the multitab function. 2. Set the water softener to the high- est level. 3. Make sure that the salt container and the rinse aid dispenser are full. 4. Start the shortest programme with a rinsing phase, without detergent and without dishes. 5. Adjust the water softener to the wa- ter hardness in your area. 6. Adjust the released quantity of rinse aid.
This function gives better results for the hygiene. During the rinsing phase, the
On · Off

Nine colours are available for this light beam. You can change the colour or deactivate it. 1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold touchpads (4) and (5) at the same time until the indica- tors of touchpads (3), (4), (5) and (6) flash.

Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results. The water softener neutralises these miner- als. The dishwasher salt keeps the water softener clean and in good conditions. Refer to the table to adjust the water softener to the right level. It makes sure that the water softener uses the correct quantity of dishwasher salt and water.
If you use the combi detergent tablets, activate the multitab function. These tablets contain detergent, rinse aid and other added agents. Be sure that these tablets are applicable to the water hardness in your area. Refer to the instructions on the packaging of the products.
You must adjust the water soft- ener manually and electronical- ly.

< 4 < 7 < 0.7 < 5 12) 12)


Turn the water hardness dial to the po- sition 1 or 2.
1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold touchpads (4) and (5) at the same time until the indica- tors of touchpads (3), (4), (5) and (6) flash. 4. Press touchpad (3). • The indicators of touchpads (4), (5) and (6) go off.

Manual adjustment · Electronic adjustment

A B
A
The rinse aid, during the last rinsing phase, helps to dry the dishes without streaks and stains.
You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 (highest quantity).
+ -

Refer to the supplied leaflet with examples of the load of the bas- kets.

A B
A
Do not use more than the cor- rect quantity of detergent. Refer to the instructions on the deter- gent packaging.
Detergent tablets do not fully dissolve with short programmes and detergent residues can stay on the dishes. We recommend that you use detergent tablets with long pro- grammes.
The appliance must be in setting mode to accept some operations. The appliance is in setting mode when, after the activation: • The display shows two horizontal sta- tus bars. If the control panel shows other condi- tions, press RESET until the appliance is in setting mode.
Starting a programme without delay start
Starting a programme with delay start
+ - · Setting mode

Make sure that there is deter- gent in the detergent dispenser before you start a new pro- gramme.
At the end of the programme
If you do not press the on/off button, the AUTO OFF device automatically deactivates the appliance after some minutes. This helps to decrease the ener- gy consumption.
Opening the door while the appliance operates
If you open the door, the appliance stops. When you close the door, the appliance continues from the point of interruption.
Cancelling the delay start while the countdown operates
There can be water on the sides and on the door of the appli- ance. Stainless steel becomes cool more quickly than the dishes.
Press RESET until: • The display shows two horizontal sta- tus bars.
Cancelling the programme

Dirty filters and clogged spray arms decrease the washing re- sults. Make a check regularly and, if necessary, clean them.
Before maintenance, deactivate the ap- pliance and disconnect the mains plug from the mains socket.

1. Turn the filter (A) counter- clockwise and remove it. 2. To disassemble the filter (A), pull apart (A1) and (A2). 3. Remove the filter (B). 4. Wash the filters with water. 5. Put the filter (B) to its initial position. Make sure that it assembles correctly under the two guides (C). 6. Assemble the filter (A) and put it into position in filter (B). Turn it clockwise until it locks.
An incorrect position of the filters can cause bad washing results and dam- age to the appliance.
Only use neutral detergents. Do not use abrasive products, abrasive clean- ing pads or solvents.
Do not remove the spray arms. If the holes in the spray arms are clog- ged, remove remaining parts of soil with a thin pointed object.
Clean the appliance with a moist soft cloth.

The appliance does not start or it stops during operation. First try to find a solution to the prob- lem (refer to the table). If not, contact Service. With some problems, the display shows an alarm code: • - The appliance does not fill with water.
Problem Possible cause Possible solution
The programme does not start.
The mains plug is not con- nected in the mains socket.
Connect the mains plug.
The appliance door is open. Close the appliance door.
The fuse in the fuse box is damaged.
Replace the fuse.
The delay start is set. Cancel the delay start or wait for the end of the countdown.
The appliance does not fill with water.
The water tap is closed. Open the water tap.
The water pressure is too low.
Contact your local water au- thority.
The water tap is clogged or there is limescale on it.
Clean the water tap.
The filter in the water inlet hose is clogged.
Clean the filter.
The water inlet hose has a kink or a bend.
Make sure that the position of the hose is correct.
The anti-flood device is on. There are water leakages in the appliance.
Close the water tap and contact Service.
The appliance does not drain the water.
The sink spigot is clogged. Clean the sink spigot.
The water drain hose has a kink or a bend.
Make sure that the position of the hose is correct.
After the checks are completed, acti- vate the appliance. The programme continues from the point of interrup- tion.
If the problem occurs again, contact Service. If the display shows other alarm codes, contact Service.

THE WASHING RESULTS AND DRYING RESULTS ARE NOT SATISFACTORY
Problem Possible cause Possible solution
The dishes are not clean.
The filters are clogged. Clean the filters.
The filters are not correctly assembled and installed.
Make sure that the filters are correctly assembled and in- stalled.
The spray arms are clog- ged.
Remove remaining soil with a thin pointed object.
The programme was not applicable for the type of load and soil.
Make sure that the pro- gramme is applicable for the type of load and soil.
Incorrect position of the items in the baskets. Water could not wash all items.
Make sure that the position of the items in the baskets is correct and that the water can easily wash all items.
The spray arms could not turn freely.
Make sure that the position of the items in the baskets is correct and does not cause the blockage of the spray arms.
The quantity of detergent was not sufficient.
Make sure that you add the correct quantity of detergent in the dispenser before you start a programme.
There was no detergent in the detergent dispenser.
Make sure that you add de- tergent in the dispenser be- fore you start a programme.
Limescale particles on the dishes.
The salt container is empty. Make sure that there is dish- washer salt in the salt con- tainer.
The set level of the water softener is incorrect.
Make sure that the set level of the water softener agrees with the water hardness in your area.
The cap of the salt contain- er is loose.
Tighten the cap.
Whitish streaks and stains or bluish lay- ers on glasses and dishes.
The released quantity of rinse aid is too much.
Decrease the released quan- tity of rinse aid .

Problem Possible cause Possible solution
The quantity of detergent was too much.
Make sure that you add the correct quantity of detergent in the dispenser before you start a programme.
Dry water drop stains on glasses and dishes.
The released quantity of rinse aid was not sufficient .
Increase the released quanti- ty of rinse aid.
The quality of the detergent can be the cause.
Try a different brand of de- tergent.
For better drying results, keep the door ajar for some minutes.
The dishes are wet and matt.
The rinse aid dispenser is empty.
Make sure that there is rinse aid in the rinse aid dispenser.
The quality of the rinse aid can be the cause.
Try a different brand of rinse aid.
The quality of the combi detergent tablets can be the cause.
Activating the rinse aid dispenser with the multitab function activated
1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold touchpads (4) and (5) at the same time until the indica- tors of touchpads (3), (4), (5) and (6) flash. 4. Press touchpad (4). • The indicators of touchpads (3), (5) and (6) go off.
Dimensions Width / Height / Depth (mm) 596 / 818 - 898 / 550
Electrical connection Refer to the rating plate.
Water supply pressure Min. / max. (bar / MPa) (0.5 / 0.05 ) / (8 / 0.8 )
Off · On

Water supply 1) Cold water or hot water2) max. 60 °C
Capacity Place settings 12
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| The programme does not start. | The mains plug is not con- nected in the mains socket. | Connect the mains plug. | p.18 |
| The programme does not start. | The appliance door is open. | Close the appliance door. | p.18 |
| The programme does not start. | The fuse in the fuse box is damaged. | Replace the fuse. | p.18 |
| The programme does not start. | The delay start is set. | Cancel the delay start or wait for the end of the countdown. | p.18 |
| The appliance does not fill with water. | The water tap is closed. | Open the water tap. | p.18 |
| The appliance does not fill with water. | The water pressure is too low. | Contact your local water au- thority. | p.18 |
| The appliance does not fill with water. | The water tap is clogged or there is limescale on it. | Clean the water tap. | p.18 |
| The appliance does not fill with water. | The filter in the water inlet hose is clogged. | Clean the filter. | p.18 |
| The appliance does not fill with water. | The water inlet hose has a kink or a bend. | Make sure that the position of the hose is correct. | p.18 |
| The appliance does not fill with water. | The anti-flood device is on. There are water leakages in the appliance. | Close the water tap and contact Service. | p.18 |
| The appliance does not drain the water. | The sink spigot is clogged. | Clean the sink spigot. | p.18 |
| The appliance does not drain the water. | The water drain hose has a kink or a bend. | Make sure that the position of the hose is correct. | p.18 |
| The dishes are not clean. | The filters are clogged. | Clean the filters. | p.19 |
| The dishes are not clean. | The filters are not correctly assembled and installed. | Make sure that the filters are correctly assembled and in- stalled. | p.19 |
| The dishes are not clean. | The spray arms are clog- ged. | Remove remaining soil with a thin pointed object. | p.19 |
| The dishes are not clean. | The programme was not applicable for the type of load and soil. | Make sure that the pro- gramme is applicable for the type of load and soil. | p.19 |
| The dishes are not clean. | Incorrect position of the items in the baskets. Water could not wash all items. | Make sure that the position of the items in the baskets is correct and that the water can easily wash all items. | p.19 |
| The dishes are not clean. | The spray arms could not turn freely. | Make sure that the position of the items in the baskets is correct and does not cause the blockage of the spray arms. | p.19 |
| The dishes are not clean. | The quantity of detergent was not sufficient. | Make sure that you add the correct quantity of detergent in the dispenser before you start a programme. | p.19 |
| The dishes are not clean. | There was no detergent in the detergent dispenser. | Make sure that you add de- tergent in the dispenser be- fore you start a programme. | p.19 |
| Limescale particles on the dishes. | The salt container is empty. | Make sure that there is dish- washer salt in the salt con- tainer. | p.19 |
| Limescale particles on the dishes. | The set level of the water softener is incorrect. | Make sure that the set level of the water softener agrees with the water hardness in your area. | p.19 |
| Limescale particles on the dishes. | The cap of the salt contain- er is loose. | Tighten the cap. | p.19 |
| Whitish streaks and stains or bluish lay- ers on glasses and dishes. | The released quantity of rinse aid is too much. | Decrease the released quan- tity of rinse aid . | p.19 |
| The quantity of detergent was too much. | Make sure that you add the correct quantity of detergent in the dispenser before you start a programme. | p.20 | |
| Dry water drop stains on glasses and dishes. | The released quantity of rinse aid was not sufficient . | Increase the released quanti- ty of rinse aid. | p.20 |
| Dry water drop stains on glasses and dishes. | The quality of the detergent can be the cause. | Try a different brand of de- tergent. | p.20 |
| The dishes are wet. | • The programme had no drying phase. • The programme had a low temperature drying phase. | For better drying results, keep the door ajar for some minutes. | p.20 |
| The dishes are wet and matt. | The rinse aid dispenser is empty. | Make sure that there is rinse aid in the rinse aid dispenser. | p.20 |
| The dishes are wet and matt. | The quality of the rinse aid can be the cause. | Try a different brand of rinse aid. | p.20 |
| The dishes are wet and matt. | The quality of the combi detergent tablets can be the cause. | • Try a different brand of combi detergent tablets. • Activate the rinse aid dis- penser and use the rinse aid together with the com- bi detergent tablets. | p.20 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.